Shahed Shaikh says:
====================
This patch series includes following changes:
* Support for spoof check configuration per VF using
iproute2 tool.
* Set HW mask for 8300 adapter in INT-x mode to stop generating
interrupts.
* Updated IRQ name for 8200 and 8300 Series adapter as per
format used by other multiqueue drivers.
* Remove qlcnic_config_npars module parameter.
* Initialize trans_work and idc_aen_work at VF probe.
* Convert netsted if-else into switch-case statement.
* Change in diagnostics routine.
* Modify reset recovery path in diag mode by providing diagnostics
routines enough time to unwind before proceeding with reset recovery.
* Implement GET_LED_STATUS command for 82xx adapter and refactor
qlcnic_store_beacon() to split 8200 and 8300 specific calls.
* Some cleanup and log enhancements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o GET_LED_STATUS command will be used by driver to get
current beacon state from 82xx adapter.
o Refactored qlcnic_store_beacon() to split 8200 and 8300
specific calls.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide diagnostics routines enough time to unwind before
proceeding with reset recovery.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test and set diagnostics mode bit before starting
diagnostics tests. Stop diagnostics tests if adapter is resetting.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o work_struct should be initialized before cancel_delayed_work
call to destroy it.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic_config_npars module parameter is used to configure NPAR
operational modes where NPAR function is used for PCI passthrough.
Removing this paramter as PCI passthrough is not supported for
NPAR functions.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Updated IRQ name for 8200 and 8300 Series adapter as per
format used by other multiqueue drivers.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Set HW mask for 8300 Series adapter, in INT-x mode, to
stop generating interrupt during driver unload.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add support for spoof check configuration per VF using
iproute2 tool.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spinlock was needed when flags used to be a u32 and set/cleared
using bit operations. Now that we use the atomic set_bit, this lock
isn't needed.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the rings reset function and increase readability by moving the
control block disable code into separate functions.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code calls tg3_set_bdinfo() separately on napi0, followed by
a loop that does napi1+. Simplify it by setting bdinfo in the loop for
all napi contexts.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike the boot signature that needs to be set before every reset, the
ape state only needs to be updated to tell the firmware that the driver
is now taking/releasing control of the hardware. Move the calls to
tg3_ape_driver_state_change() to better, more appropriate places.
Also, the firmware does not distinguish between SUSPEND and START states
anymore. Remove the SUSPEND case in the switch.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge net into net-next because some upcoming net-next changes
build on top of bug fixes that went into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull gfs2 fixes from Steven Whitehouse:
"This time there are just four fixes. There are a couple of minor
updates to the quota code, a fix for KConfig to ensure that only valid
combinations including GFS2 can be built, and a fix for a typo
affecting end i/o processing when writing the journal.
Also, there is a temporary fix for a performance regression relating
to block reservations and directories. A longer fix will be applied
in due course, but this deals with the most immediate problem for now"
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
GFS2: Fix typo in gfs2_log_end_write loop
GFS2: fix DLM depends to fix build errors
GFS2: Use single-block reservations for directories
GFS2: two minor quota fixups
Pull powerpc fixes from Benjamin Herrenschmidt:
"Some more P8 related bits, a bunch of fixes for our P7+/P8 HW crypto
drivers, some added workarounds for those radeons that don't do proper
64-bit MSIs and a couple of other trivialities by myself."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pseries: Make 32-bit MSI quirk work on systems lacking firmware support
powerpc/powernv: Build a zImage.epapr
powerpc: Make radeon 32-bit MSI quirk work on powernv
powerpc: Context switch more PMU related SPRs
powerpc/powernv: Fix condition for when to invalidate the TCE cache
powerpc/pci: Fix bogus message at boot about empty memory resources
powerpc: Fix TLB cleanup at boot on POWER8
drivers/crypto/nx: Fixes for multiple races and issues
Pull networking fixes from David Miller:
"It's been a while since my last pull request so quite a few fixes have
piled up."
Indeed.
1) Fix nf_{log,queue} compilation with PROC_FS disabled, from Pablo
Neira Ayuso.
2) Fix data corruption on some tg3 chips with TSO enabled, from Michael
Chan.
3) Fix double insertion of VLAN tags in be2net driver, from Sarveshwar
Bandi.
4) Don't have TCP's MD5 support pass > PAGE_SIZE page offsets in
scatter-gather entries into the crypto layer, the crypto layer can't
handle that. From Eric Dumazet.
5) Fix lockdep splat in 802.1Q MRP code, also from Eric Dumazet.
6) Fix OOPS in netfilter log module when called from conntrack, from
Hans Schillstrom.
7) FEC driver needs to use netif_tx_{lock,unlock}_bh() rather than the
non-BH disabling variants. From Fabio Estevam.
8) TCP GSO can generate out-of-order packets, fix from Eric Dumazet.
9) vxlan driver doesn't update 'used' field of fdb entries when it
should, from Sridhar Samudrala.
10) ipv6 should use kzalloc() to allocate inet6 socket cork options,
otherwise we can OOPS in ip6_cork_release(). From Eric Dumazet.
11) Fix races in bonding set mode, from Nikolay Aleksandrov.
12) Fix checksum generation regression added by "r8169: fix 8168evl
frame padding.", from Francois Romieu.
13) ip_gre can look at stale SKB data pointer, fix from Eric Dumazet.
14) Fix checksum handling when GSO is enabled in bnx2x driver with
certain chips, from Yuval Mintz.
15) Fix double free in batman-adv, from Martin Hundebøll.
16) Fix device startup synchronization with firmware in tg3 driver, from
Nithin Sujit.
17) perf networking dropmonitor doesn't work at all due to mixed up
trace parameter ordering, from Ben Hutchings.
18) Fix proportional rate reduction handling in tcp_ack(), from Nandita
Dukkipati.
19) IPSEC layer doesn't return an error when a valid state is detected,
causing an OOPS. Fix from Timo Teräs.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (85 commits)
be2net: bug fix on returning an invalid nic descriptor
tcp: xps: fix reordering issues
net: Revert unused variable changes.
xfrm: properly handle invalid states as an error
virtio_net: enable napi for all possible queues during open
tcp: bug fix in proportional rate reduction.
net: ethernet: sun: drop unused variable
net: ethernet: korina: drop unused variable
net: ethernet: apple: drop unused variable
qmi_wwan: Added support for Cinterion's PLxx WWAN Interface
perf: net_dropmonitor: Remove progress indicator
perf: net_dropmonitor: Use bisection in symbol lookup
perf: net_dropmonitor: Do not assume ordering of dictionaries
perf: net_dropmonitor: Fix symbol-relative addresses
perf: net_dropmonitor: Fix trace parameter order
net: fec: use a more proper compatible string for MVF type device
qlcnic: Fix updating netdev->features
qlcnic: remove netdev->trans_start updates within the driver
qlcnic: Return proper error codes from probe failure paths
tg3: Update version to 3.132
...
Fix build errors by correcting DLM dependencies in GFS2.
Build errors happen when CONFIG_GFS2_FS_LOCKING_DLM=y and CONFIG_DLM=m:
fs/built-in.o: In function `gfs2_lock':
file.c:(.text+0xc7abd): undefined reference to `dlm_posix_get'
file.c:(.text+0xc7ad0): undefined reference to `dlm_posix_unlock'
file.c:(.text+0xc7ad9): undefined reference to `dlm_posix_lock'
fs/built-in.o: In function `gdlm_unmount':
lock_dlm.c:(.text+0xd6e5b): undefined reference to `dlm_release_lockspace'
fs/built-in.o: In function `sync_unlock':
lock_dlm.c:(.text+0xd6e9e): undefined reference to `dlm_unlock'
fs/built-in.o: In function `sync_lock':
lock_dlm.c:(.text+0xd6fb6): undefined reference to `dlm_lock'
fs/built-in.o: In function `gdlm_put_lock':
lock_dlm.c:(.text+0xd7238): undefined reference to `dlm_unlock'
fs/built-in.o: In function `gdlm_mount':
lock_dlm.c:(.text+0xd753e): undefined reference to `dlm_new_lockspace'
lock_dlm.c:(.text+0xd79d3): undefined reference to `dlm_release_lockspace'
fs/built-in.o: In function `gdlm_lock':
lock_dlm.c:(.text+0xd8179): undefined reference to `dlm_lock'
fs/built-in.o: In function `gdlm_cancel':
lock_dlm.c:(.text+0xd6b22): undefined reference to `dlm_unlock'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch changes the multi-block allocation code, such that
directory inodes only get a single block reserved in the bitmap.
That way, the bitmaps are more tightly packed together, and there
are fewer spans of free blocks for in-use block reservations.
This means it takes less time to find a free span of blocks in the
bitmap, which speeds things up. This increases the performance of
some workloads by almost 2X. In Nate's mockup.py script (which does
(1) create dir, (2) create dir in dir, (3) create file in that dir)
the test executes in 23 steps rather than 43 steps, a 47%
performance improvement.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch fixes two regression problems that Abhi found in the
GFS2 quota code.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Recent commit e61133dda4 added support
for a new firmware feature to force an adapter to use 32 bit MSIs.
However, this firmware is not available for all systems. The hack below
allows devices needing 32 bit MSIs to work on these systems as well.
It is careful to only enable this on Gen2 slots, which should limit
this to configurations where this hack is needed and tested to work.
[Small change to factor out the hack into a separate function -- BenH]
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The zImage.epapr wrapper allows to use zImages when booting via a flat
device-tree which can be used on powernv.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This moves the quirk itself to pci_64.c as to get built on all ppc64
platforms (the only ones with a pci_dn), factors the two implementations
of get_pdn() into a single pci_get_dn() and use the quirk to do 32-bit
MSIs on IODA based powernv platforms.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In commit 9353374 "Context switch the new EBB SPRs" we added support for
context switching some new EBB SPRs. However despite four of us signing
off on that patch we missed some. To be fair these are not actually new
SPRs, but they are now potentially user accessible so need to be context
switched.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We use two flags, one to indicate an invalidation is needed after
creating a new entry and one to indicate an invalidation is needed
after removing an entry. However we were testing the wrong flag
in the remove case.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The message is only meant to be displayed if resource 0 is empty,
but was displayed if any is.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The TLB has 512 congruence classes (2048 entries 4 way set associative)
while P7 had 128
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes a race on driver init with registering algorithms where the
driver status flag wasn't being set before self testing started.
Added the cra_alignmask field for CBC and ECB modes.
Fixed a bug in GCM where AES block size was being used instead of
authsize.
Removed use of blkcipher_walk routines for scatterlist processing.
Corner cases in the code prevent us from processing an entire
scatterlist at a time and walking the buffers in block sized chunks
turns out to be unecessary anyway.
Fixed off-by-one error in saving off extra data in the sha code.
Fixed accounting error for number of bytes processed in the sha code.
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Refactor all TX HW workarounds into a separate routine called
be_xmit_workarounds().
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function be_get_nic_desc(), it will go through the descriptor array
returned from f/w. By comparing the desc_type field, it determines whether
there is a nic descriptor in the array or not. In the case of no nic
descriptor, this function should return NULL.
The code may return an invalide descriptor, when there is no nic descriptor
in the array and the desc_count is less than MAX_RESOURCE_DESC. In this case,
even there is no nic descriptor, it will still return the lase descriptor
since the i doesn't equal to MAX_RESOURCE_DESC.
This patch fix this issue by returning the descriptor when find it and return
NULL for other cases.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Acked-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Explain the mechanism and API of the recently merged
rps flow limit patch.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When vlan device is configured on top of the brige, it does
not support any offload capabilities because the bridge
device does not initiliaze vlan_fatures. Set vlan_fatures to
be equivalent to hw_fatures.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz says:
====================
This series contain several small enhancements - chief among those are
the implementation of ethtool's private flags callback to share information
about the storage offload capabilities of its network interfaces,
and the prevention of a link flap when booting from storage area networks.
Changes from V1:
- Patch 1, removed trailing whitespaces from private flag strings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In Multi-function mode, all functions should be able to utilize said function;
There's no reason why only the link owner should be able to do so.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During PCIe advanced error recovery, the secondary bus reset will cause FW
to reset; This will cause the shared memory between it and the driver to be
invalidated.
During the driver's recovery flow, the driver should not make any assumption
on the validity of that memory and instead re-initialize it.
This also removes a redundant re-initialization of a previously
initialized mutex.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the previous unload flow, probed devices will reset the chip
in order to clean the remains of the UNDI driver.
As a result, it's possible for the FW to toggle the link.
This toggling can prove fatal, as long periods without link can cause the
filesystem mount to fail as the storage protocol timeouts. This has been
observed against particular switches with long link re-establishment time.
This patch informs FW during the reset period that the link should not
be toggled - the FW will keep it alive until some interface will load and claim
the link as its own.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize ethtool's callback `get_priv_flags' - shed more light on the
feasibility of devices as storage interfaces.
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Liu says:
====================
This series adds a new feature called split event channels.
In the original implementation, only one event channel is setup between
frontend and backend. This is not ideal as TX notification interferes with RX
notification. Using dedicated event channels for TX and RX solves this issue.
Changes since V2:
* feature_split_event_channels -> separate_tx_rx_irq
* make separate_tx_rx_irq bool
* document this feature in header file
* don't report fatal if writing feature to xenstore fails
* frontend will fall back to single event channel if new feature setup fails
Changes since V1:
* change subject lines of commits to be more specific
* add parameter feature_split_event_channels for xen-netback
* remove two dev_info
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch synchronises documentation for feature-split-event-channels from
Xen canonical header file.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new feature called feature-split-event-channels for
netfront, enabling it to handle TX and RX events separately.
If netback does not support this feature, it falls back to use single event
channel.
If netfront fails to setup split event channels, it will try falling back to
single event channel.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netback and netfront only use one event channel to do TX / RX notification,
which may cause unnecessary wake-up of processing routines. This patch adds a
new feature called feature-split-event-channels to netback, enabling it to
handle TX and RX events separately.
Netback will use tx_irq to notify guest for TX completion, rx_irq for RX
notification.
If frontend doesn't support this feature, tx_irq equals to rx_irq.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 3853b5841c ("xps: Improvements in TX queue selection")
introduced ooo_okay flag, but the condition to set it is slightly wrong.
In our traces, we have seen ACK packets being received out of order,
and RST packets sent in response.
We should test if we have any packets still in host queue.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- An OMAP fix that makes ethernet work again.
- Fix for build problem when building the MCP23S08 driver
as module.
- IRQ conflicts in the Langwell driver.
- Fix IRQ coherency issues in the MXS driver.
- Return correct errorcode on errorpath when removing
GPIO chips.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=dxQl
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-v3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
- An OMAP fix that makes ethernet work again.
- Fix for build problem when building the MCP23S08 driver as module.
- IRQ conflicts in the Langwell driver.
- Fix IRQ coherency issues in the MXS driver.
- Return correct errorcode on errorpath when removing GPIO chips.
* tag 'gpio-fixes-v3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: Don't override the error code in probe error handling
gpio: mxs: Use set and clear capabilities of the gpio controller
gpio-langwell: fix irq conflicts when DT is not used
gpio: mcp23s08: Fix build error when CONFIG_SPI_MASTER=y && CONFIG_I2C=m
gpio/omap: ensure gpio context is initialised
