Commit graph

78771 commits

Author SHA1 Message Date
Ken Kawasaki
ceba0b29e0 axnet_cs: remove unnecessary spin_unlock_irqrestore
axnet_cs:
    remove unnecessary spin_unlock_irqrestore,spin_lock_irqsave.

Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03 21:52:44 -08:00
Julia Lawall
75ed0a8972 drivers/net/cxgb3: Use kzalloc for allocating only one thing
Use kzalloc rather than kcalloc(1,...)

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
@@

- kcalloc(1,
+ kzalloc(
          ...)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03 21:22:28 -08:00
Andy Gospodarek
1f3c8804ac bonding: allow arp_ip_targets on separate vlans to use arp validation
This allows a bond device to specify an arp_ip_target as a host that is
not on the same vlan as the base bond device and still use arp
validation.  A configuration like this, now works:

BONDING_OPTS="mode=active-backup arp_interval=1000 arp_ip_target=10.0.100.1 arp_validate=3"

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: eth1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000
    link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
3: eth0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000
    link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
8: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue
    link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
    inet6 fe80::213:21ff:febe:33e9/64 scope link
       valid_lft forever preferred_lft forever
9: bond0.100@bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue
    link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
    inet 10.0.100.2/24 brd 10.0.100.255 scope global bond0.100
    inet6 fe80::213:21ff:febe:33e9/64 scope link
       valid_lft forever preferred_lft forever

Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)

Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth1
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
ARP Polling Interval (ms): 1000
ARP IP target/s (n.n.n.n form): 10.0.100.1

Slave Interface: eth1
MII Status: up
Link Failure Count: 1
Permanent HW addr: 00:40:05:30:ff:30

Slave Interface: eth0
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:13:21:be:33:e9

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03 21:17:16 -08:00
David S. Miller
3a999e6eb5 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 2009-12-30 13:51:29 -08:00
John W. Linville
891dc5e737 Merge git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
Conflicts:
	drivers/net/wireless/libertas/scan.c
2009-12-30 15:25:08 -05:00
H Hartley Sweeten
6cd9b49d73 Subject: drivers/net/sh_eth.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-29 20:10:35 -08:00
H Hartley Sweeten
30a6ae8d47 drivers/net/r8169.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-29 20:10:01 -08:00
H Hartley Sweeten
e583482091 drivers/net/octeon/octeon_mgmt.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-29 20:09:07 -08:00
H Hartley Sweeten
fa876b474a drivers/net/smc911x.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-29 20:08:09 -08:00
H Hartley Sweeten
b18fe4777f drivers/net/sunvnet.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-29 20:07:27 -08:00
H Hartley Sweeten
3b8dff3622 drivers/net/usb/catc.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-29 20:06:45 -08:00
H Hartley Sweeten
d998ab0bd7 drivers/s390/net/qeth_l2_main.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-29 20:05:37 -08:00
H Hartley Sweeten
5491f3a562 drivers/net/xilinx_emaclite.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-29 20:04:53 -08:00
H Hartley Sweeten
aa7c68a5f7 drivers/net/via-velocity.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-29 20:04:14 -08:00
H Hartley Sweeten
d649a2844e drivers/net/usb/rtl8150.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-29 20:03:28 -08:00
H Hartley Sweeten
753cdc3304 drivers/net/igbvf/netdev.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-29 20:02:29 -08:00
H Hartley Sweeten
557b0bbd62 drivers/net/lib82596.c: use %pM to shown MAC address
Use the %pM kernel extension to display the MAC address.

The only difference in the output is that the MAC address is
shown in the usual colon-separated hex notation instead of
space-separated.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-29 20:01:46 -08:00
John W. Linville
55afc80b2a Revert "b43: Enforce DMA descriptor memory constraints"
This reverts commit 9bd568a50c.

That commit is shown to cause allocation failures during initialization
on some machines.

http://bugzilla.kernel.org/show_bug.cgi?id=14844

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-29 14:07:42 -05:00
Johannes Berg
1ed32e4fc8 mac80211: remove struct ieee80211_if_init_conf
All its members (vif, mac_addr, type) are now available
in the vif struct directly, so we can pass that instead
of the conf struct. I generated this patch (except the
mac80211 and header file changes) with this semantic
patch:

@@
identifier conf, fn, hw;
type tp;
@@
tp fn(struct ieee80211_hw *hw,
-struct ieee80211_if_init_conf *conf)
+struct ieee80211_vif *vif)
{
<...
(
-conf->type
+vif->type
|
-conf->mac_addr
+vif->addr
|
-conf->vif
+vif
)
...>
}

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:55:07 -05:00
Johannes Berg
a80f7c0b08 mac80211: introduce flush operation
We've long lacked a good confirmation that frames
have really gone out, e.g. before going off-channel
for a scan. Add a flush() operation that drivers
can implement to provide that confirmation, and use
it in a few places:
 * before scanning sends the nullfunc frames
 * after scanning sends the nullfunc frames, if any
 * when going idle, to send any pending frames

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:54:51 -05:00
John W. Linville
d30506e035 rtl8187: remove priv->mode
It is checked in add_interface, but there it is easily replaced with
a check of priv->vif.  If that information should become necessary,
it is available in vif->type anyway.

It is also checked in led_turn_on and led_turn_off, where I made the
substitutions as described above.  Of course, these checks seem to
have been incorrect since the driver was using NL80211_IFTYPE_MONITOR
to indicate no interface rather than NL80211_IFTYPE_UNSPECIFIED.
Anyway, I think these checks may be extraneous...?

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:38 -05:00
John W. Linville
643aab6733 rtl8180: remove priv->mode
It is only checked in add_interface, and there it is easily replaced
with a check of priv->vif.  If that information should become necessary,
it is available in vif->type anyway.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:38 -05:00
Gertjan van Wingerde
5122d89862 rt2x00: Cleanup chip handling helper functions.
Let each of them take a struct rt2x00_dev pointer as argument instead of
a mixture of struct rt2x00_chip and struct rt2x00_dev pointers.
Preparation for further clean ups in the rt2x00 chip handling, especially
for rt2800 devices.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:38 -05:00
Gertjan van Wingerde
73a2f1259e rt2x00: convert RT2800PCI_PCI and RT2800PCI_SOC Kconfig symbols to booleans.
There is no need for Kconfig symbols RT2800PCI_PCI and RT2800PCI_SOC to be
tristates, as they are only used to check whether RT2800 PCI or SOC support
is to be compiled in.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:37 -05:00
Gertjan van Wingerde
ac394917f5 rt2x00: Let rt2800lib check CONFIG_RT2X00_LIB_USB instead of CONFIG_RT2800USB
rt2800lib currently checks whether RT2800USB is enabled in the configuration.
Strictly speaking this is not necessary, it only needs to know whether the
generic rt2x00usb library functions are available. Therefore check for
RT2X00_LIB_USB instead.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:37 -05:00
Gertjan van Wingerde
00e23ce219 rt2x00: Fix checks for rt2800 SOC support.
Fix checking for SOC support in rt2800pci. The wrong config (an unexisting
one) was checked.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:37 -05:00
Juuso Oikarinen
8f648c0003 wl1271: Prevent performing "join" before association
There is a minor bug in the code causing a "join" to be performed before
there is an intention to associate. Fix this.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:36 -05:00
Juuso Oikarinen
04477bf095 wl1271: Check vif for NULL when indicating beacon-loss
Because the interface is started and the vif are created and destroyed
separately, there is a slim possibility beacon-loss indications occur while
there is no vif - causing a kernel-oops unless checked.

Add checking for the vif.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:36 -05:00
Juuso Oikarinen
38ad2d87d4 wl1271: Add support for acx_pm_config
This acx configures host clock parameters in correspondence with the clock
request line - the settling time of the clock, and whether fast wake-up is
supported.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:36 -05:00
Juuso Oikarinen
71449f8d70 wl1271: Change booleans in struct wl1271 into a flags bitmask
For cleaner implementation, change the bunch of booleans in the struct wl1271
structure into a flags bitmask.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:35 -05:00
Juuso Oikarinen
830fb67b8e wl1271: Fix supported rate management
Previously, only basic rates were used for data transmission - resulting in
reduced transfer rates. This patch takes enables the firmware to take advantage
of the full set of data rates supported by the AP.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:35 -05:00
Juuso Oikarinen
ec078d943b wl1271: Change rates configured for templates
Previously a "firmware chooses" value was used for the rates of all control
message templates set to the firmware. This resulted in a too high rate to be
chosen to transmit those messages. Change this by configuring a fixed low rate
for the templates.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:35 -05:00
Juuso Oikarinen
e0d8bbf0d2 wl1271: Add rudimentary ad-hoc support
This patch adds rudimentary a-hoc support for the driver. It will allow
setting up ad-hoc, and for other devices to scan and join. The beacon and probe
response template setting is slightly dirty, and need to be properly
implemented with support from mac80211. Also, the SSID is not configured to the
firmware - the FW will not be able to respond to probe requests autonomously.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:35 -05:00
Juuso Oikarinen
26a63f6af5 wl1271: Remove beacon-loss-ind from PSM entry failure handling
Remove the beacon-loss indication to stack from PSM entry failure handling -
this will cause more problems than it will solve due to the design of the
mac80211.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:35 -05:00
Juuso Oikarinen
01ac17ecb6 wl1271: Add pre-power-on sleep
This patch adds a short delay before powering on the wl1271. Normally, it is
not needed, but if the wl1271 has been powered off shortly before, for reliable
firmware-booting this small stabilization delay is required.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:34 -05:00
Juuso Oikarinen
9ccd921792 wl1271: Implement chipset boot retry
The wl1271 has a hardware bug which causes it to randomly (very infrequently)
to fail powering up properly. This patch implements retry for the chipset boot
sequence, to work around the hardware problem.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:34 -05:00
Juuso Oikarinen
af5e084b32 wl1271: prevent power save entry while not associated
The mac80211 sometimes requests power save entry while not associated - this
will cause problems, so prevent it if not associated. Go to powersave once
association is complete.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:34 -05:00
Juuso Oikarinen
13f2dc52c6 wl1271: Fix event acknowledging functionality
In reference source, events are acknowledged separately - fix the driver to
do the same.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:34 -05:00
Juuso Oikarinen
a6fe231361 wl1271: Use slow rates for association messages
While not associated, default the data rates to 1 and 2mbps, so that only
those rates will be used for association related message transfer. Once
associated, configure the full rate-set supported by the AP.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:33 -05:00
Juuso Oikarinen
018b171c40 wl1271: Remove smart reflex ACX
Remove the smart-reflex ACX - the associated parameters are now configured
in the radio parameters config.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:33 -05:00
Juuso Oikarinen
149e38789f wl1271: Configure smart-reflex paramter values.
Configure correct values to be used with the smart-reflex configuration of the
firmware.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:33 -05:00
Luciano Coelho
94210897e2 wl1271: use channel 1 when configuring the data path
In the data path configuration, one of the parameters is the channel.  We
have been setting it to wl->channel, which is not correct in this case.  This
channel has nothing to do with the channel we're currently tuned to, since it
is only used for calibration during this phase.  Hardcoded the channel to 1,
according to the reference driver.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:33 -05:00
Luciano Coelho
3ed8f2c614 wl1271: some new configuration values according to new reference
In the new reference driver, some of the firmware configuration values have
been changed.  This patch changes them in the wl1271 driver accordingly.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:32 -05:00
Luciano Coelho
8cf5e8e509 wl1271: upload only the first 468 bytes from the NVS file
We were uploading the whole NVS file, but that is wrong, because the same
file also contains the initialization values.  For the latest firmwares, we
should upload only the initial 468 bytes from the file.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:32 -05:00
Luciano Coelho
98b2a68473 wl1271: add gpio_power file in debugfs to power the chip on and off
Some debugging tools require the chip to be powered on before they can work.
With these tools, we shouldn't upload the firmware nor boot the firmware
ourselves, so this debufs file is provided.  It always contains the gpio
power setting (0 = off, 1 = on).  To change the power setting, just write 0
or 1 to the file.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:32 -05:00
Luciano Coelho
1b38ea8858 wl1271: fix one typo in the rx_rssi_and_proc_compens values
There was a typo in one of the values in the rx_rssi_and_proc_compens elemt
of the Radio Parameters struct.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:32 -05:00
Luciano Coelho
6e92b416b0 wl1271: implement dco itrim parameters setting
Newer firmwares require the dco itrim parameters to be set during
initialization.  This patch implements the new ACX function and calls it.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:31 -05:00
Luciano Coelho
ac9b40fac6 wl1271: use the correct macro when setting the basic rates
We were using CONF_TX_RATE_MASK_ALL when calling wl1271_acx_rate_policies()
during init.  We should use WL1271_DEFAULT_BASIC_RATE_SET instead.  The
values are the same, but the latter is just the correct macro to use.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:31 -05:00
Luciano Coelho
bdcbbb947b wl1271: set null data template when BSSID is known
The call to wl1271_cmd_build_null_data() was missing when we got associated,
this was causing PS to fail.  This patch adds the call and now PS seems to
work.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:31 -05:00
Luciano Coelho
cd264769f7 wl1271: check result code from the join command
We were not checking the return value from the call to wl1271_cmd_join().
Added a check to make things more reliable.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:30 -05:00