Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 4960 Errata 3.27 identifies that ssthresh should be adjusted to cwnd
because otherwise it could cause the transport to lock into congestion
avoidance phase specially if ssthresh was previously reduced by some
packet drop, leading to poor performance.
The Errata says to adjust ssthresh to cwnd only once, though the same
goal is achieved by updating it every time we update cwnd too. The
caveat is that we could take longer to get back up to speed but that
should be compensated by the fact that we don't adjust on RTO basis (as
RFC says) but based on Heartbeats, which are usually way longer.
See-also: https://tools.ietf.org/html/draft-ietf-tsvwg-rfc4960-errata-01#section-3.27
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC4960 Errata 3.26 identified that at the same time RFC4960 states that
cwnd should never grow more than 1*MTU per RTT, Section 7.2.2 was
underspecified and as described could allow increasing cwnd more than
that.
This patch updates it so partial_bytes_acked is maxed to cwnd if
flight_size doesn't reach cwnd, protecting it from such case.
See-also: https://tools.ietf.org/html/draft-ietf-tsvwg-rfc4960-errata-01#section-3.26
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per RFC4960 Errata 3.22, this condition is not needed anymore as it
could cause the partial_bytes_acked to not consider the TSNs acked in
the Gap Ack Blocks although they were received by the peer successfully.
This patch thus drops the check for new Cumulative TSN Ack Point,
leaving just the flight_size < cwnd one.
See-also: https://tools.ietf.org/html/draft-ietf-tsvwg-rfc4960-errata-01#section-3.22
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC4960 Errata 3.12 says RFC4960 is unclear about the order of
adjustments applied to partial_bytes_acked and cwnd in the congestion
avoidance phase, and that the actual order should be:
partial_bytes_acked is reset to (partial_bytes_acked - cwnd). Next, cwnd
is increased by MTU.
We were first increasing cwnd, and then subtracting the new value pba,
which leads to a different result as pba is smaller than what it should
and could cause cwnd to not grow as much.
See-also: https://tools.ietf.org/html/draft-ietf-tsvwg-rfc4960-errata-01#section-3.12
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify that the caller-provided sockaddr structure is large enough to
contain the sa_family field, before accessing it in bind() and connect()
handlers of the AF_IUCV socket. Since neither syscall enforces a minimum
size of the corresponding memory region, very short sockaddrs (zero or
one byte long) result in operating on uninitialized memory while
referencing .sa_family.
Fixes: 52a82e23b9 ("af_iucv: Validate socket address length in iucv_sock_bind()")
Signed-off-by: Mateusz Jurczyk <mjurczyk@google.com>
[jwi: removed unneeded null-check for addr]
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use proper endianness conversion for an skb protocol assignment. Given
that IUCV is only available on big endian systems (s390), this simply
avoids an endianness warning reported by sparse.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switches and modern SR-IOV enabled NICs may multiplex traffic from Port
representators and control messages over single set of hardware queues.
Control messages and muxed traffic may need ordered delivery.
Those requirements make it hard to comfortably use TC infrastructure today
unless we have a way of attaching metadata to skbs at the upper device.
Because single set of queues is used for many netdevs stopping TC/sched
queues of all of them reliably is impossible and lower device has to
retreat to returning NETDEV_TX_BUSY and usually has to take extra locks on
the fastpath.
This patch attempts to enable port/representative devs to attach metadata
to skbs which carry port id. This way representatives can be queueless and
all queuing can be performed at the lower netdev in the usual way.
Traffic arriving on the port/representative interfaces will be have
metadata attached and will subsequently be queued to the lower device for
transmission. The lower device should recognize the metadata and translate
it to HW specific format which is most likely either a special header
inserted before the network headers or descriptor/metadata fields.
Metadata is associated with the lower device by storing the netdev pointer
along with port id so that if TC decides to redirect or mirror the new
netdev will not try to interpret it.
This is mostly for SR-IOV devices since switches don't have lower netdevs
today.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The copy_to_user() function returns the number of bytes remaining but we
want to return -EFAULT here.
Fixes: 3c4d755915 ("tls: kernel TLS support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-06-23
1) Use memdup_user to spmlify xfrm_user_policy.
From Geliang Tang.
2) Make xfrm_dev_register static to silence a sparse warning.
From Wei Yongjun.
3) Use crypto_memneq to check the ICV in the AH protocol.
From Sabrina Dubroca.
4) Remove some unused variables in esp6.
From Stephen Hemminger.
5) Extend XFRM MIGRATE to allow to change the UDP encapsulation port.
From Antony Antony.
6) Include the UDP encapsulation port to km_migrate announcements.
From Antony Antony.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
KASAN reports out-of-bound access in proc_dostring() coming from
proc_tcp_available_ulp() because in case TCP ULP list is empty
the buffer allocated for the response will not have anything
printed into it. Set the first byte to zero to avoid strlen()
going out-of-bounds.
Fixes: 734942cc4e ("tcp: ULP infrastructure")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 31fd85816d ("bpf: permits narrower load from bpf program
context fields") permits narrower load for certain ctx fields.
The commit however will already generate a masking even if
the prog-specific ctx conversion produces the result with
narrower size.
For example, for __sk_buff->protocol, the ctx conversion
loads the data into register with 2-byte load.
A narrower 2-byte load should not generate masking.
For __sk_buff->vlan_present, the conversion function
set the result as either 0 or 1, essentially a byte.
The narrower 2-byte or 1-byte load should not generate masking.
To avoid unnecessary masking, prog-specific *_is_valid_access
now passes converted_op_size back to verifier, which indicates
the valid data width after perceived future conversion.
Based on this information, verifier is able to avoid
unnecessary marking.
Since we want more information back from prog-specific
*_is_valid_access checking, all of them are packed into
one data structure for more clarity.
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the XDP_ATTACHED_* values to include offloaded mode.
Let drivers report whether program is installed in the driver
or the HW by changing the prog_attached field from bool to
u8 (type of the netlink attribute).
Exploit the fact that the value of XDP_ATTACHED_DRV is 1,
therefore since all drivers currently assign the mode with
double negation:
mode = !!xdp_prog;
no drivers have to be modified.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an installation-time flag for requesting that the program
be installed only if it can be offloaded to HW.
Internally new command for ndo_xdp is added, this way we avoid
putting checks into drivers since they all return -EINVAL on
an unknown command.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass XDP flags to the xdp ndo. This will allow drivers to look
at the mode flags and make decisions about offload.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael reported an UDP breakage caused by the commit b65ac44674
("udp: try to avoid 2 cache miss on dequeue").
The function __first_packet_length() can update the checksum bits
of the pending skb, making the scratched area out-of-sync, and
setting skb->csum, if the skb was previously in need of checksum
validation.
On later recvmsg() for such skb, checksum validation will be
invoked again - due to the wrong udp_skb_csum_unnecessary()
value - and will fail, causing the valid skb to be dropped.
This change addresses the issue refreshing the scratch area in
__first_packet_length() after the possible checksum update.
Fixes: b65ac44674 ("udp: try to avoid 2 cache miss on dequeue")
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
very similar to commit dd99e425be ("udp: prefetch
rmem_alloc in udp_queue_rcv_skb()"), this allows saving a cache
miss when the BH is bottle-neck for UDP over ipv6 packet
processing, e.g. for small packets when a single RX NIC ingress
queue is in use.
Performances under flood when multiple NIC RX queues used are
unaffected, but when a single NIC rx queue is in use, this
gives ~8% performance improvement.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we are unloading the rds_tcp module, we can set linger to 1
and drop pending packets to accelerate reconnect. The peer will
end up resetting the connection based on new generation numbers
of the new incarnation, so hanging on to unsent TCP packets via
linger is mostly pointless in this case.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Jenny Xu <jenny.x.xu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RDS handshake ping probe added by commit 5916e2c155
("RDS: TCP: Enable multipath RDS for TCP") is sent from rds_sendmsg()
before the first data packet is sent to a peer. If the conversation
is not bidirectional (i.e., one side is always passive and never
invokes rds_sendmsg()) and the passive side restarts its rds_tcp
module, a new HS ping probe needs to be sent, so that the number
of paths can be re-established.
This patch achieves that by sending a HS ping probe from
rds_tcp_accept_one() when c_npaths is 0 (i.e., we have not done
a handshake probe with this peer yet).
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Jenny Xu <jenny.x.xu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in both ipv4 and ipv6 code path, the ack packet received when
sk at TCP_NEW_SYN_RECV state is not filtered by socket filter or cgroup
filter since it is handled from tcp_child_process and never reaches the
tcp_filter inside tcp_v4_rcv or tcp_v6_rcv. Adding a tcp_filter hooks
here can make sure all the ingress tcp packet can be correctly filtered.
Signed-off-by: Chenbo Feng <fengc@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two entries being added at the same time to the IFLA
policy table, whilst parallel bug fixes to decnet
routing dst handling overlapping with the dst gc removal
in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be able to retrieve the attached programs from cls_bpf
and act_bpf, we need to expose the prog ids via netlink so that
an application can later on get an fd based on the id through the
BPF_PROG_GET_FD_BY_ID command, and dump related prog info via
BPF_OBJ_GET_INFO_BY_FD command for bpf(2).
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the new getsockopt(2) option SO_PEERGROUPS on SOL_SOCKET to
retrieve the auxiliary groups of the remote peer. It is designed to
naturally extend SO_PEERCRED. That is, the underlying data is from the
same credentials. Regarding its syntax, it is based on SO_PEERSEC. That
is, if the provided buffer is too small, ERANGE is returned and @optlen
is updated. Otherwise, the information is copied, @optlen is set to the
actual size, and 0 is returned.
While SO_PEERCRED (and thus `struct ucred') already returns the primary
group, it lacks the auxiliary group vector. However, nearly all access
controls (including kernel side VFS and SYSVIPC, but also user-space
polkit, DBus, ...) consider the entire set of groups, rather than just
the primary group. But this is currently not possible with pure
SO_PEERCRED. Instead, user-space has to work around this and query the
system database for the auxiliary groups of a UID retrieved via
SO_PEERCRED.
Unfortunately, there is no race-free way to query the auxiliary groups
of the PID/UID retrieved via SO_PEERCRED. Hence, the current user-space
solution is to use getgrouplist(3p), which itself falls back to NSS and
whatever is configured in nsswitch.conf(3). This effectively checks
which groups we *would* assign to the user if it logged in *now*. On
normal systems it is as easy as reading /etc/group, but with NSS it can
resort to quering network databases (eg., LDAP), using IPC or network
communication.
Long story short: Whenever we want to use auxiliary groups for access
checks on IPC, we need further IPC to talk to the user/group databases,
rather than just relying on SO_PEERCRED and the incoming socket. This
is unfortunate, and might even result in dead-locks if the database
query uses the same IPC as the original request.
So far, those recursions / dead-locks have been avoided by using
primitive IPC for all crucial NSS modules. However, we want to avoid
re-inventing the wheel for each NSS module that might be involved in
user/group queries. Hence, we would preferably make DBus (and other IPC
that supports access-management based on groups) work without resorting
to the user/group database. This new SO_PEERGROUPS ioctl would allow us
to make dbus-daemon work without ever calling into NSS.
Cc: Michal Sekletar <msekleta@redhat.com>
Cc: Simon McVittie <simon.mcvittie@collabora.co.uk>
Reviewed-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On UDP packets processing, if the BH is the bottle-neck, it
always sees a cache miss while updating rmem_alloc; try to
avoid it prefetching the value as soon as we have the socket
available.
Performances under flood with multiple NIC rx queues used are
unaffected, but when a single NIC rx queue is in use, this
gives ~10% performance improvement.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Netlink notifications on cache reports in ip6mr, in addition to the
existing mrt6msg sent to mroute6_sk.
Send RTM_NEWCACHEREPORT notifications to RTNLGRP_IPV6_MROUTE_R.
MSGTYPE, MIF_ID, SRC_ADDR and DST_ADDR Netlink attributes contain the
same data as their equivalent fields in the mrt6msg header.
PKT attribute is the packet sent to mroute6_sk, without the added
mrt6msg header.
Suggested-by: Ryan Halbrook <halbrook@arista.com>
Signed-off-by: Julien Gomes <julien@arista.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Netlink notifications on cache reports in ipmr, in addition to the
existing igmpmsg sent to mroute_sk.
Send RTM_NEWCACHEREPORT notifications to RTNLGRP_IPV4_MROUTE_R.
MSGTYPE, VIF_ID, SRC_ADDR and DST_ADDR Netlink attributes contain the
same data as their equivalent fields in the igmpmsg header.
PKT attribute is the packet sent to mroute_sk, without the added igmpmsg
header.
Suggested-by: Ryan Halbrook <halbrook@arista.com>
Signed-off-by: Julien Gomes <julien@arista.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add RTNLGRP_{IPV4,IPV6}_MROUTE_R as two new restricted groups for the
NETLINK_ROUTE family.
Binding to these groups specifically requires CAP_NET_ADMIN to allow
multicast of sensitive messages (e.g. mroute cache reports).
Suggested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Julien Gomes <julien@arista.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing from a memcpy to per-member comparison left the
size variable unused:
net/ipv4/tcp_ipv4.c: In function 'tcp_md5_do_lookup':
net/ipv4/tcp_ipv4.c:910:15: error: unused variable 'size' [-Werror=unused-variable]
This does not show up when CONFIG_IPV6 is enabled, but the
variable can be removed either way, along with the now unused
assignment.
Fixes: 6797318e62 ("tcp: md5: add an address prefix for key lookup")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey reported a lockdep warning on non-initialized
spinlock:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 1 PID: 4099 Comm: a.out Not tainted 4.12.0-rc6+ #9
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16
dump_stack+0x292/0x395 lib/dump_stack.c:52
register_lock_class+0x717/0x1aa0 kernel/locking/lockdep.c:755
? 0xffffffffa0000000
__lock_acquire+0x269/0x3690 kernel/locking/lockdep.c:3255
lock_acquire+0x22d/0x560 kernel/locking/lockdep.c:3855
__raw_spin_lock_bh ./include/linux/spinlock_api_smp.h:135
_raw_spin_lock_bh+0x36/0x50 kernel/locking/spinlock.c:175
spin_lock_bh ./include/linux/spinlock.h:304
ip_mc_clear_src+0x27/0x1e0 net/ipv4/igmp.c:2076
igmpv3_clear_delrec+0xee/0x4f0 net/ipv4/igmp.c:1194
ip_mc_destroy_dev+0x4e/0x190 net/ipv4/igmp.c:1736
We miss a spin_lock_init() in igmpv3_add_delrec(), probably
because previously we never use it on this code path. Since
we already unlink it from the global mc_tomb list, it is
probably safe not to acquire this spinlock here. It does not
harm to have it although, to avoid conditional locking.
Fixes: c38b7d327a ("igmp: acquire pmc lock for ip_mc_clear_src()")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network interface groups support added while ago, however
there is no IFLA_GROUP attribute description in policy
and netlink message size calculations until now.
Add IFLA_GROUP attribute to the policy.
Fixes: cbda10fa97 ("net_device: add support for network device groups")
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While commit 73ba57bfae ("ipv6: fix backtracking for throw routes")
does good job on error propagation to the fib_rules_lookup()
in fib rules core framework that also corrects throw routes
handling, it does not solve route reference leakage problem
happened when we return -EAGAIN to the fib_rules_lookup()
and leave routing table entry referenced in arg->result.
If rule with matched throw route isn't last matched in the
list we overwrite arg->result losing reference on throw
route stored previously forever.
We also partially revert commit ab997ad408 ("ipv6: fix the
incorrect return value of throw route") since we never return
routing table entry with dst.error == -EAGAIN when
CONFIG_IPV6_MULTIPLE_TABLES is on. Also there is no point
to check for RTF_REJECT flag since it is always set throw
route.
Fixes: 73ba57bfae ("ipv6: fix backtracking for throw routes")
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's a bad thing not to handle errors when updating asoc. The memory
allocation failure in any of the functions called in sctp_assoc_update()
would cause sctp to work unexpectedly.
This patch is to fix it by aborting the asoc and reporting the error when
any of these functions fails.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
local_cork is used to decide if it should uncork asoc outq after processing
some cmds, and it is set when replying or sending msgs. local_cork should
always have the same value with current asoc q->cork in some way.
The thing is when changing to a new asoc by cmd SET_ASOC, local_cork may
not be consistent with the current asoc any more. The cmd seqs can be:
SCTP_CMD_UPDATE_ASSOC (asoc)
SCTP_CMD_REPLY (asoc)
SCTP_CMD_SET_ASOC (new_asoc)
SCTP_CMD_DELETE_TCB (new_asoc)
SCTP_CMD_SET_ASOC (asoc)
SCTP_CMD_REPLY (asoc)
The 1st REPLY makes OLD asoc q->cork and local_cork both are 1, and the cmd
DELETE_TCB clears NEW asoc q->cork and local_cork. After asoc goes back to
OLD asoc, q->cork is still 1 while local_cork is 0. The 2nd REPLY will not
set local_cork because q->cork is already set and it can't be uncorked and
sent out because of this.
To keep local_cork consistent with the current asoc q->cork, this patch is
to uncork the old asoc if local_cork is set before changing to the new one.
Note that the above cmd seqs will be used in the next patch when updating
asoc and handling errors in it.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch "call inet_add_protocol after register_pernet_subsys in dccp_v4_init"
fixed a null pointer dereference issue for dccp_ipv4 module.
The same fix is needed for dccp_ipv6 module.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now dccp_ipv4 works as a kernel module. During loading this module, if
one dccp packet is being recieved after inet_add_protocol but before
register_pernet_subsys in which v4_ctl_sk is initialized, a null pointer
dereference may be triggered because of init_net.dccp.v4_ctl_sk is 0x0.
Jianlin found this issue when the following call trace occurred:
[ 171.950177] BUG: unable to handle kernel NULL pointer dereference at 0000000000000110
[ 171.951007] IP: [<ffffffffc0558364>] dccp_v4_ctl_send_reset+0xc4/0x220 [dccp_ipv4]
[...]
[ 171.984629] Call Trace:
[ 171.984859] <IRQ>
[ 171.985061]
[ 171.985213] [<ffffffffc0559a53>] dccp_v4_rcv+0x383/0x3f9 [dccp_ipv4]
[ 171.985711] [<ffffffff815ca054>] ip_local_deliver_finish+0xb4/0x1f0
[ 171.986309] [<ffffffff815ca339>] ip_local_deliver+0x59/0xd0
[ 171.986852] [<ffffffff810cd7a4>] ? update_curr+0x104/0x190
[ 171.986956] [<ffffffff815c9cda>] ip_rcv_finish+0x8a/0x350
[ 171.986956] [<ffffffff815ca666>] ip_rcv+0x2b6/0x410
[ 171.986956] [<ffffffff810c83b4>] ? task_cputime+0x44/0x80
[ 171.986956] [<ffffffff81586f22>] __netif_receive_skb_core+0x572/0x7c0
[ 171.986956] [<ffffffff810d2c51>] ? trigger_load_balance+0x61/0x1e0
[ 171.986956] [<ffffffff81587188>] __netif_receive_skb+0x18/0x60
[ 171.986956] [<ffffffff8158841e>] process_backlog+0xae/0x180
[ 171.986956] [<ffffffff8158799d>] net_rx_action+0x16d/0x380
[ 171.986956] [<ffffffff81090b7f>] __do_softirq+0xef/0x280
[ 171.986956] [<ffffffff816b6a1c>] call_softirq+0x1c/0x30
This patch is to move inet_add_protocol after register_pernet_subsys in
dccp_v4_init, so that v4_ctl_sk is initialized before any incoming dccp
packets are processed.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no good reason to keep the flags twice in vxlan_dev and
vxlan_config.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 217f697436 ("net: busy-poll: allow preemption in
sk_busy_loop()") there is an explicit do_softirq() invocation after
local_bh_enable() has been invoked.
I don't understand why we need this because local_bh_enable() will
invoke do_softirq() once the softirq counter reached zero and we have
softirq-related work pending.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should avoid marking goto rules unresolved when their
target is actually reachable after rule deletion.
Consolder following sample scenario:
# ip -4 ru sh
0: from all lookup local
32000: from all goto 32100
32100: from all lookup main
32100: from all lookup default
32766: from all lookup main
32767: from all lookup default
# ip -4 ru del pref 32100 table main
# ip -4 ru sh
0: from all lookup local
32000: from all goto 32100 [unresolved]
32100: from all lookup default
32766: from all lookup main
32767: from all lookup default
After removal of first rule with preference 32100 we
mark all goto rules as unreachable, even when rule with
same preference as removed one still present.
Check if next rule with same preference is available
and make all rules with goto action pointing to it.
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now before dumping a sock in sctp_diag, it only holds the sock while
the ep may be already destroyed. It can cause a use-after-free panic
when accessing ep->asocs.
This patch is to set sctp_sk(sk)->ep NULL in sctp_endpoint_destroy,
and check if this ep is already destroyed before dumping this ep.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdrver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace first padding in the tcp_md5sig structure with a new flag field
and address prefix length so it can be specified when configuring a new
key for TCP MD5 signature. The tcpm_flags field will only be used if the
socket option is TCP_MD5SIG_EXT to avoid breaking existing programs, and
tcpm_prefixlen only when the TCP_MD5SIG_FLAG_PREFIX flag is set.
Signed-off-by: Bob Gilligan <gilligan@arista.com>
Signed-off-by: Eric Mowat <mowat@arista.com>
Signed-off-by: Ivan Delalande <colona@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows the keys used for TCP MD5 signature to be used for whole
range of addresses, specified with a prefix length, instead of only one
address as it currently is.
Signed-off-by: Bob Gilligan <gilligan@arista.com>
Signed-off-by: Eric Mowat <mowat@arista.com>
Signed-off-by: Ivan Delalande <colona@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* remove wext calling ndo_do_ioctl, since nobody needs
that now and it makes the type change easier
* use struct iwreq instead of struct ifreq almost everywhere
in wireless extensions code
* copy only struct iwreq from userspace in dev_ioctl for the
wireless extensions, since it's smaller than struct ifreq
-----BEGIN PGP SIGNATURE-----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=O240
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-06-16' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here's just the fix for that ancient bug:
* remove wext calling ndo_do_ioctl, since nobody needs
that now and it makes the type change easier
* use struct iwreq instead of struct ifreq almost everywhere
in wireless extensions code
* copy only struct iwreq from userspace in dev_ioctl for the
wireless extensions, since it's smaller than struct ifreq
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Same as ip_gre, geneve and vxlan, use key->tos as traffic class value.
CC: Peter Dawson <petedaws@gmail.com>
Fixes: 0e9a709560 ("ip6_tunnel, ip6_gre: fix setting of DSCP on
encapsulated packets”)
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: Peter Dawson <peter.a.dawson@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 6d3c8c0dd8 ("net: dsa: Remove master_netdev and
use dst->cpu_dp->netdev") and a29342e739 ("net: dsa: Associate
slave network device with CPU port") we would be seeing NULL pointer
dereferences when accessing dst->cpu_dp->netdev too early. In the legacy
code, we actually know early in advance the master network device, so
pass it down to the relevant functions.
Fixes: 6d3c8c0dd8 ("net: dsa: Remove master_netdev and use dst->cpu_dp->netdev")
Fixes: a29342e739 ("net: dsa: Associate slave network device with CPU port")
Reported-by: Jason Cobham <jcobham@questertangent.com>
Tested-by: Jason Cobham <jcobham@questertangent.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Missing crypto deps for some platforms.
Default to n for new module.
config: m68k-amcore_defconfig (attached as .config)
compiler: m68k-linux-gcc (GCC) 4.9.0
make.cross ARCH=m68k
All errors (new ones prefixed by >>):
net/built-in.o: In function `tls_set_sw_offload':
>> (.text+0x732f8): undefined reference to `crypto_alloc_aead'
net/built-in.o: In function `tls_set_sw_offload':
>> (.text+0x7333c): undefined reference to `crypto_aead_setkey'
net/built-in.o: In function `tls_set_sw_offload':
>> (.text+0x73354): undefined reference to `crypto_aead_setauthsize'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DST_NOCACHE flag check has been removed from dst_release() and
dst_hold_safe() in a previous patch because all the dst are now ref
counted properly and can be released based on refcnt only.
Looking at the rest of the DST_NOCACHE use, all of them can now be
removed or replaced with other checks.
So this patch gets rid of all the DST_NOCACHE usage and remove this flag
completely.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all the components have been changed to release dst based on
refcnt only and not depend on dst gc anymore, we can remove the
temporary flag DST_NOGC.
Note that we also need to remove the DST_NOCACHE check in dst_release()
and dst_hold_safe() because now all the dst are released based on refcnt
and behaves as DST_NOCACHE.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matthias Schiffer