Add support to emulate the CXL the "Secure Erase" operation.
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Link: https://lore.kernel.org/r/20230612181038.14421-8-dave@stgolabs.net
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add support to emulate the "Sanitize" operation, without
incurring in the background.
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Link: https://lore.kernel.org/r/20230612181038.14421-6-dave@stgolabs.net
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
commit eb0764b822 ("cxl/port: Enable the HDM decoder capability for switch ports")
...was added on the observation of CXL memory not being accessible after
setting up a region on a "cold-plugged" device. A "cold-plugged" CXL
device is one that was not present at boot, so platform-firmware/BIOS
has no chance to set it up.
While it is true that the debug found the enable bit clear in the
host-bridge's instance of the global control register (CXL 3.0
8.2.4.19.2 CXL HDM Decoder Global Control Register), that bit is
described as:
"This bit is only applicable to CXL.mem devices and shall
return 0 on CXL Host Bridges and Upstream Switch Ports."
So it is meant to be zero, and further testing confirmed that this "fix"
had no effect on the failure. Revert it, and be more vigilant about
proposed fixes in the future. Since the original copied stable@, flag
this revert for stable@ as well.
Cc: <stable@vger.kernel.org>
Fixes: eb0764b822 ("cxl/port: Enable the HDM decoder capability for switch ports")
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/168685882012.3475336.16733084892658264991.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for support for HDM-D and HDM-DB configuration
(device-memory, and device-memory with back-invalidate). Rename the current
type designators to use HOSTONLYMEM and DEVMEM as a suffix.
HDM-DB can be supported by devices that are not accelerators, so DEVMEM is
a more generic term for that case.
Fixup one location where this type value was open coded.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/168679261369.3436160.7042443847605280593.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
'struct cxl_dev_state' makes too many assumptions about the capabilities
of a CXL device. In particular it assumes a CXL device has a mailbox and
all of the infrastructure and state that comes along with that.
In preparation for supporting accelerator / Type-2 devices that may not
have a mailbox and in general maintain a minimal core context structure,
make mailbox functionality a super-set of 'struct cxl_dev_state' with
'struct cxl_memdev_state'.
With this reorganization it allows for CXL devices that support HDM
decoder mapping, but not other general-expander / Type-3 capabilities,
to only enable that subset without the rest of the mailbox
infrastructure coming along for the ride.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/168679260240.3436160.15520641540463704524.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for plumbing a 'struct cxl_memdev_state' as a superset of
a 'struct cxl_dev_state' cleanup the usage of @cxlds in the unit test
infrastructure.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/168679258640.3436160.7641308222525246728.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For symmetry with the recent rename of ->dport_dev for a 'struct
cxl_dport', add the "_dev" suffix to the ->uport property of a 'struct
cxl_port'. These devices represent the downstream-port-device and
upstream-port-device respectively in the CXL/PCIe topology.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20230622205523.85375-6-terry.bowman@amd.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Prepare cxl_probe_rcrb() for retrieving more than just the component
register block. The RCH AER handling code wants to get back to the AER
capability that happens to be MMIO mapped rather then configuration
cycles.
Move RCRB specific downstream port data, like the RCRB base and the
AER capability offset, into its own data structure ('struct
cxl_rcrb_info') for cxl_probe_rcrb() to fill. Extend 'struct
cxl_dport' to include a 'struct cxl_rcrb_info' attribute.
This centralizes all RCRB scanning in one routine.
Co-developed-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20230622205523.85375-4-terry.bowman@amd.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The RCRB is extracted already during ACPI CEDT table parsing while the
data of this is needed not earlier than dport creation. This
implementation comes with drawbacks: During ACPI table scan there is
already MMIO access including mapping and unmapping, but only ACPI
data should be collected here. The collected data must be transferred
through a couple of interfaces until it is finally consumed when
creating the dport. This causes complex data structures and function
interfaces. Additionally, RCRB parsing will be extended to also
extract AER data, it would be much easier do this at a later point
during port and dport creation when the data structures are available
to hold that data.
To simplify all that, probe the RCRB at a later point during RCH
downstream port creation. Change ACPI table parser to only extract the
base address of either the component registers or the RCRB. Parse and
extract the RCRB in devm_cxl_add_rch_dport().
This is in preparation to centralize all RCRB scanning.
Signed-off-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20230622205523.85375-2-terry.bowman@amd.com
Co-developed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/20230622205523.85375-3-terry.bowman@amd.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Spell "transmissions" properly.
Found by searching for keyword "tranm".
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Yueh-Shun Li <shamrocklee@posteo.net>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20230623-send-net-next-20230623-v1-8-a883213c8ba9@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch moves endpoint settings out of do_transfer() into a new
helper pm_nl_set_endpoint(). And invoke this helper in do_transfer().
This makes the code much more clearer.
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20230623-send-net-next-20230623-v1-7-a883213c8ba9@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
run_tests() accepts too many optional parameters. Before this modification,
it was required to set all of then when only the last one had to be
changed. That's not clear to see all these 0 and it makes the maintenance
harder:
run_tests $ns1 $ns2 10.0.1.1 1 2 3 slow
Instead, the parameter can be set as an env var with a limited scope:
foo=1 bar=2 next=3 \
run_tests $ns1 $ns2 10.0.1.1 slow
This patch switches to key/value "sflags=*" instead of positional parameter
sflags of do_transfer() and run_tests().
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20230623-send-net-next-20230623-v1-6-a883213c8ba9@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
run_tests() accepts too many optional parameters. Before this modification,
it was required to set all of then when only the last one had to be
changed. That's not clear to see all these 0 and it makes the maintenance
harder:
run_tests $ns1 $ns2 10.0.1.1 1 2 3 slow
Instead, the parameter can be set as an env var with a limited scope:
foo=1 bar=2 next=3 \
run_tests $ns1 $ns2 10.0.1.1 slow
This patch switches to key/value "addr_nr_ns1=*, addr_nr_ns2=*" instead
of positional parameters addr_nr_ns1 and addr_nr_ns2 of do_transfer()
and run_tests().
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20230623-send-net-next-20230623-v1-5-a883213c8ba9@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
run_tests() accepts too many optional parameters. Before this modification,
it was required to set all of then when only the last one had to be
changed. That's not clear to see all these 0 and it makes the maintenance
harder:
run_tests $ns1 $ns2 10.0.1.1 1 2 3 slow
Instead, the parameter can be set as an env var with a limited scope:
foo=1 bar=2 next=3 \
run_tests $ns1 $ns2 10.0.1.1 slow
This patch switches to key/value "test_linkfail=*" instead of positional
parameter test_linkfail of do_transfer() and run_tests().
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20230623-send-net-next-20230623-v1-4-a883213c8ba9@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Set FAILING_LINKS as an env var with a limited scope only when calling
run_tests().
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20230623-send-net-next-20230623-v1-3-a883213c8ba9@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
New MPTCP info are being checked in multiple places to improve the code
coverage when using the userspace PM.
This patch makes chk_mptcp_info() more generic to be able to check
subflows, add_addr_signal and add_addr_accepted info (and even more
later). New arguments are now required to get different infos from the
two namespaces because some counters are specific to the client or the
server.
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20230623-send-net-next-20230623-v1-2-a883213c8ba9@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch moves userspace pm tests out of do_transfer(). Move add address
test into a new function userspace_pm_add_addr(), and remove address test
into userspace_pm_rm_sf_addr_ns1(). Move add subflow test into
userspace_pm_add_sf() and remove subflow into
userspace_pm_rm_sf_addr_ns2().
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20230623-send-net-next-20230623-v1-1-a883213c8ba9@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On systems where netdevsim is built-in or loaded before the test
starts, kci_test_ipsec_offload doesn't remove the netdevsim device it
created during the test.
Fixes: e05b2d141f ("netdevsim: move netdev creation/destruction to dev probe")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/e1cb94f4f82f4eca4a444feec4488a1323396357.1687466906.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCZJX+ygAKCRDbK58LschI
g0/2AQDHg12smf9mPfK9wOFDNRIIX8r2iufB8LUFQMzCwltN6gEAkAdkAyfbof7P
TMaNUiHABijAFtChxoSI35j3OOSRrwE=
=GJgN
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:
====================
pull-request: bpf-next 2023-06-23
We've added 49 non-merge commits during the last 24 day(s) which contain
a total of 70 files changed, 1935 insertions(+), 442 deletions(-).
The main changes are:
1) Extend bpf_fib_lookup helper to allow passing the route table ID,
from Louis DeLosSantos.
2) Fix regsafe() in verifier to call check_ids() for scalar registers,
from Eduard Zingerman.
3) Extend the set of cpumask kfuncs with bpf_cpumask_first_and()
and a rework of bpf_cpumask_any*() kfuncs. Additionally,
add selftests, from David Vernet.
4) Fix socket lookup BPF helpers for tc/XDP to respect VRF bindings,
from Gilad Sever.
5) Change bpf_link_put() to use workqueue unconditionally to fix it
under PREEMPT_RT, from Sebastian Andrzej Siewior.
6) Follow-ups to address issues in the bpf_refcount shared ownership
implementation, from Dave Marchevsky.
7) A few general refactorings to BPF map and program creation permissions
checks which were part of the BPF token series, from Andrii Nakryiko.
8) Various fixes for benchmark framework and add a new benchmark
for BPF memory allocator to BPF selftests, from Hou Tao.
9) Documentation improvements around iterators and trusted pointers,
from Anton Protopopov.
10) Small cleanup in verifier to improve allocated object check,
from Daniel T. Lee.
11) Improve performance of bpf_xdp_pointer() by avoiding access
to shared_info when XDP packet does not have frags,
from Jesper Dangaard Brouer.
12) Silence a harmless syzbot-reported warning in btf_type_id_size(),
from Yonghong Song.
13) Remove duplicate bpfilter_umh_cleanup in favor of umd_cleanup_helper,
from Jarkko Sakkinen.
14) Fix BPF selftests build for resolve_btfids under custom HOSTCFLAGS,
from Viktor Malik.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (49 commits)
bpf, docs: Document existing macros instead of deprecated
bpf, docs: BPF Iterator Document
selftests/bpf: Fix compilation failure for prog vrf_socket_lookup
selftests/bpf: Add vrf_socket_lookup tests
bpf: Fix bpf socket lookup from tc/xdp to respect socket VRF bindings
bpf: Call __bpf_sk_lookup()/__bpf_skc_lookup() directly via TC hookpoint
bpf: Factor out socket lookup functions for the TC hookpoint.
selftests/bpf: Set the default value of consumer_cnt as 0
selftests/bpf: Ensure that next_cpu() returns a valid CPU number
selftests/bpf: Output the correct error code for pthread APIs
selftests/bpf: Use producer_cnt to allocate local counter array
xsk: Remove unused inline function xsk_buff_discard()
bpf: Keep BPF_PROG_LOAD permission checks clear of validations
bpf: Centralize permissions checks for all BPF map types
bpf: Inline map creation logic in map_create() function
bpf: Move unprivileged checks into map_create() and bpf_prog_load()
bpf: Remove in_atomic() from bpf_link_put().
selftests/bpf: Verify that check_ids() is used for scalars in regsafe()
bpf: Verify scalar ids mapping in regsafe() using check_ids()
selftests/bpf: Check if mark_chain_precision() follows scalar ids
...
====================
Link: https://lore.kernel.org/r/20230623211256.8409-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previously used to specify symbol_name_rb_node was in use.
Signed-off-by: Ian Rogers <irogers@google.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Carsten Haitzler <carsten.haitzler@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Jason Wang <wangborong@cdjrlc.com>
Cc: Changbin Du <changbin.du@huawei.com>
Cc: Yang Jihong <yangjihong1@huawei.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20230623054520.4118442-4-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Most perf commands want to sort symbols by name and this is done via
an invasive rbtree that on 64-bit systems costs 24 bytes. Sorting the
symbols in a DSO by name is optional and not done by default, however,
if sorting is requested the 24 bytes is allocated for every
symbol.
This change removes the rbtree and uses a sorted array of symbol
pointers instead (costing 8 bytes per symbol). As the array is created
on demand then there are further memory savings. The complexity of
sorting the array and using the rbtree are the same.
To support going to the next symbol, the index of the current symbol
needs to be passed around as a pair with the current symbol. This
requires some API changes.
Signed-off-by: Ian Rogers <irogers@google.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Carsten Haitzler <carsten.haitzler@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Jason Wang <wangborong@cdjrlc.com>
Cc: Changbin Du <changbin.du@huawei.com>
Cc: Yang Jihong <yangjihong1@huawei.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20230623054520.4118442-3-irogers@google.com
[ minimize change in symbols__sort_by_name() ]
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Determine if symbols are sorted, set the sorted flag and sort under
the dso lock. Done in the interest of thread safety.
Signed-off-by: Ian Rogers <irogers@google.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Carsten Haitzler <carsten.haitzler@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Jason Wang <wangborong@cdjrlc.com>
Cc: Changbin Du <changbin.du@huawei.com>
Cc: Yang Jihong <yangjihong1@huawei.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20230623054520.4118442-2-irogers@google.com
[ handle the similar code in util/probe-event.c ]
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
If generating vmlinux.h, make the code to generate it more tolerant by
filtering out paths to kernels that lack a .BTF section.
Signed-off-by: Ian Rogers <irogers@google.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: James Clark <james.clark@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Yang Jihong <yangjihong1@huawei.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Tiezhu Yang <yangtiezhu@loongson.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: bpf@vger.kernel.org
Link: https://lore.kernel.org/r/20230623041405.4039475-5-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Add tests with and without generating vmlinux.h.
Signed-off-by: Ian Rogers <irogers@google.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: James Clark <james.clark@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Yang Jihong <yangjihong1@huawei.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Tiezhu Yang <yangtiezhu@loongson.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: bpf@vger.kernel.org
Link: https://lore.kernel.org/r/20230623041405.4039475-4-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
struct rq is defined in vmlinux.h when the vmlinux.h is generated,
this causes a redefinition failure if it is declared in
lock_contention.bpf.c. Move the definition to vmlinux.h for
consistency with the generated version.
Fixes: 760ebc4574 ("perf lock contention: Add empty 'struct rq' to satisfy libbpf 'runqueue' type verification")
Signed-off-by: Ian Rogers <irogers@google.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: James Clark <james.clark@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Yang Jihong <yangjihong1@huawei.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Tiezhu Yang <yangtiezhu@loongson.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: bpf@vger.kernel.org
Link: https://lore.kernel.org/r/20230623041405.4039475-3-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
This test checks if the output of perf stat to match event names and
metrics. So it wants the output lines to have both event name and
metric. Otherwise it should skip the line.
On AMD machines, the instruction event has two metrics and they are printed
in separate lines. It makes the line without event name like below:
# perf stat -a sleep 1
Performance counter stats for 'system wide':
64,383.34 msec cpu-clock # 64.048 CPUs utilized
14,526 context-switches # 225.617 /sec
112 cpu-migrations # 1.740 /sec
190 page-faults # 2.951 /sec
807,558,652 cycles # 0.013 GHz (83.30%)
69,809,799 stalled-cycles-frontend # 8.64% frontend cycles idle (83.30%)
196,983,266 stalled-cycles-backend # 24.39% backend cycles idle (83.30%)
424,876,008 instructions # 0.53 insn per cycle
(here) ---> # 0.46 stalled cycles per insn (83.30%)
97,788,321 branches # 1.519 M/sec (83.34%)
4,147,377 branch-misses # 4.24% of all branches (83.46%)
1.005241409 seconds time elapsed
Also modern Intel machines have TopDown metrics which also don't have
event names.
# perf stat -a sleep 1
Performance counter stats for 'system wide':
8,015.39 msec cpu-clock # 7.996 CPUs utilized
5,823 context-switches # 726.477 /sec
189 cpu-migrations # 23.580 /sec
139 page-faults # 17.342 /sec
435,139,308 cycles # 0.054 GHz
193,891,345 instructions # 0.45 insn per cycle
42,773,028 branches # 5.336 M/sec
2,298,113 branch-misses # 5.37% of all branches
TopdownL1 # 25.5 % tma_backend_bound
/--> # 7.9 % tma_bad_speculation
(here) --+ # 55.7 % tma_frontend_bound
\--> # 10.9 % tma_retiring
1.002395924 seconds time elapsed
There is a check to skip TopdownL1 and TopdownL2 specifically but it
does not cover every affected lines.
So there is another check to skip the line if it has nothing on the left
side of # sign. Well.. it seems ok but that's not enough too.
When aggregation mode (like --per-socket or --per-thread) is used, it
adds some prefix (e.g. CPU socket, task name and PID) in the output
line. So the test code ignores them to normalize result.
A problem can happen for per-thread mode when task name contains one or
more spaces. It'd only ignore the first part of the task name, and it
thinks there's something more in the line so it would not skip.
# perf stat -a --perf-thread sleep 1
...
perf-21276 # 70.2 % tma_backend_bound
perf-21276 # 3.9 % tma_bad_speculation
perf-21276 # 10.5 % tma_frontend_bound
perf-21276 # 15.3 % tma_retiring
^^^^^^^^^^
(ignored)
my task-21328 # 70.2 % tma_backend_bound
my task-21328 # 3.9 % tma_bad_speculation
my task-21328 # 10.5 % tma_frontend_bound
my task-21328 # 15.3 % tma_retiring
^^
(ignored)
So I think it should look at the metric names instead. Add skip_metric
to hold the list of names to skip. It would contain 'stalled cycles per
insn' and metrics started by 'tma_'.
Fixes: 99a04a48f2 ("perf test: Add test case for the standard 'perf stat' output")
Acked-by: Ian Rogers <irogers@google.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230623230139.985594-2-namhyung@kernel.org
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Commit a887466562 ("perf bpf skels: Stop using vmlinux.h generated
from BTF, use subset of used structs + CO-RE") made it so that
vmlinux.h was uncondtionally included from
tools/perf/util/vmlinux.h. This change reverts part of that change (so
that vmlinux.h is once again generated) and makes it so that the
vmlinux.h used at build time is selected from the VMLINUX_H
variable. By default the VMLINUX_H variable is set to the vmlinux.h
added in change a887466562, but if GEN_VMLINUX_H=1 is passed on the
build command line then the previous generation behavior kicks in.
The build with GEN_VMLINUX_H=1 currently fails with:
util/bpf_skel/lock_contention.bpf.c:419:8: error: redefinition of 'rq'
struct rq {};
^
/tmp/perf/util/bpf_skel/.tmp/../vmlinux.h:45630:8: note: previous definition is here
struct rq {
^
1 error generated.
Signed-off-by: Ian Rogers <irogers@google.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: James Clark <james.clark@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Yang Jihong <yangjihong1@huawei.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Tiezhu Yang <yangtiezhu@loongson.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: bpf@vger.kernel.org
Link: https://lore.kernel.org/r/20230623041405.4039475-2-irogers@google.com
[ Format the error message and add a comment for GEN_VMLINUX_H ]
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
On AMD machines, the perf stat STD output test failed like below:
$ sudo ./perf test -v 98
98: perf stat STD output linter :
--- start ---
test child forked, pid 1841901
Checking STD output: no argswrong event metric.
expected 'GHz' in 108,121 stalled-cycles-frontend # 10.88% frontend cycles idle
test child finished with -1
---- end ----
perf stat STD output linter: FAILED!
This is because there are stalled-cycles-{frontend,backend} events are
used by default. The current logic checks the event_name array to find
which event it's running. But 'cycles' event comes before those stalled
cycles event and it matches first. So it tries to find 'GHz' metric
in the output (which is for the 'cycles') and fails.
Move the stalled-cycles-{frontend,backend} events before 'cycles' so
that it can find the stalled cycles events first.
Also add a space after 'no args' test name for consistency.
Fixes: 99a04a48f2 ("perf test: Add test case for the standard 'perf stat' output")
Acked-by: Ian Rogers <irogers@google.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230623230139.985594-1-namhyung@kernel.org
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Before server got a client connection, there were some memory allocations
in the test memcg, such as user stack. So do not count those allocations
which are not related to socket when checking socket memory accounting.
Link: https://lkml.kernel.org/r/20230619124735.2124-1-haifeng.xu@shopee.com
Signed-off-by: Haifeng Xu <haifeng.xu@shopee.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Michal Koutný <mkoutny@suse.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
* arm64/for-next/perf:
docs: perf: Fix warning from 'make htmldocs' in hisi-pmu.rst
docs: perf: Add new description for HiSilicon UC PMU
drivers/perf: hisi: Add support for HiSilicon UC PMU driver
drivers/perf: hisi: Add support for HiSilicon H60PA and PAv3 PMU driver
perf: arm_cspmu: Add missing MODULE_DEVICE_TABLE
perf/arm-cmn: Add sysfs identifier
perf/arm-cmn: Revamp model detection
perf/arm_dmc620: Add cpumask
dt-bindings: perf: fsl-imx-ddr: Add i.MX93 compatible
drivers/perf: imx_ddr: Add support for NXP i.MX9 SoC DDRC PMU driver
perf/arm_cspmu: Decouple APMT dependency
perf/arm_cspmu: Clean up ACPI dependency
ACPI/APMT: Don't register invalid resource
perf/arm_cspmu: Fix event attribute type
perf: arm_cspmu: Set irq affinitiy only if overflow interrupt is used
drivers/perf: hisi: Don't migrate perf to the CPU going to teardown
drivers/perf: apple_m1: Force 63bit counters for M2 CPUs
perf/arm-cmn: Fix DTC reset
perf: qcom_l2_pmu: Make l2_cache_pmu_probe_cluster() more robust
perf/arm-cci: Slightly optimize cci_pmu_sync_counters()
* for-next/kpti:
: Simplify KPTI trampoline exit code
arm64: entry: Simplify tramp_alias macro and tramp_exit routine
arm64: entry: Preserve/restore X29 even for compat tasks
* for-next/missing-proto-warn:
: Address -Wmissing-prototype warnings
arm64: add alt_cb_patch_nops prototype
arm64: move early_brk64 prototype to header
arm64: signal: include asm/exception.h
arm64: kaslr: add kaslr_early_init() declaration
arm64: flush: include linux/libnvdimm.h
arm64: module-plts: inline linux/moduleloader.h
arm64: hide unused is_valid_bugaddr()
arm64: efi: add efi_handle_corrupted_x18 prototype
arm64: cpuidle: fix #ifdef for acpi functions
arm64: kvm: add prototypes for functions called in asm
arm64: spectre: provide prototypes for internal functions
arm64: move cpu_suspend_set_dbg_restorer() prototype to header
arm64: avoid prototype warnings for syscalls
arm64: add scs_patch_vmlinux prototype
arm64: xor-neon: mark xor_arm64_neon_*() static
* for-next/iss2-decode:
: Add decode of ISS2 to data abort reports
arm64/esr: Add decode of ISS2 to data abort reporting
arm64/esr: Use GENMASK() for the ISS mask
* for-next/kselftest:
: Various arm64 kselftest improvements
kselftest/arm64: Log signal code and address for unexpected signals
kselftest/arm64: Add a smoke test for ptracing hardware break/watch points
* for-next/misc:
: Miscellaneous patches
arm64: alternatives: make clean_dcache_range_nopatch() noinstr-safe
arm64: hibernate: remove WARN_ON in save_processor_state
arm64/fpsimd: Exit streaming mode when flushing tasks
arm64: mm: fix VA-range sanity check
arm64/mm: remove now-superfluous ISBs from TTBR writes
arm64: consolidate rox page protection logic
arm64: set __exception_irq_entry with __irq_entry as a default
arm64: syscall: unmask DAIF for tracing status
arm64: lockdep: enable checks for held locks when returning to userspace
arm64/cpucaps: increase string width to properly format cpucaps.h
arm64/cpufeature: Use helper for ECV CNTPOFF cpufeature
* for-next/feat_mops:
: Support for ARMv8.8 memcpy instructions in userspace
kselftest/arm64: add MOPS to hwcap test
arm64: mops: allow disabling MOPS from the kernel command line
arm64: mops: detect and enable FEAT_MOPS
arm64: mops: handle single stepping after MOPS exception
arm64: mops: handle MOPS exceptions
KVM: arm64: hide MOPS from guests
arm64: mops: don't disable host MOPS instructions from EL2
arm64: mops: document boot requirements for MOPS
KVM: arm64: switch HCRX_EL2 between host and guest
arm64: cpufeature: detect FEAT_HCX
KVM: arm64: initialize HCRX_EL2
* for-next/module-alloc:
: Make the arm64 module allocation code more robust (clean-up, VA range expansion)
arm64: module: rework module VA range selection
arm64: module: mandate MODULE_PLTS
arm64: module: move module randomization to module.c
arm64: kaslr: split kaslr/module initialization
arm64: kasan: remove !KASAN_VMALLOC remnants
arm64: module: remove old !KASAN_VMALLOC logic
* for-next/sysreg: (21 commits)
: More sysreg conversions to automatic generation
arm64/sysreg: Convert TRBIDR_EL1 register to automatic generation
arm64/sysreg: Convert TRBTRG_EL1 register to automatic generation
arm64/sysreg: Convert TRBMAR_EL1 register to automatic generation
arm64/sysreg: Convert TRBSR_EL1 register to automatic generation
arm64/sysreg: Convert TRBBASER_EL1 register to automatic generation
arm64/sysreg: Convert TRBPTR_EL1 register to automatic generation
arm64/sysreg: Convert TRBLIMITR_EL1 register to automatic generation
arm64/sysreg: Rename TRBIDR_EL1 fields per auto-gen tools format
arm64/sysreg: Rename TRBTRG_EL1 fields per auto-gen tools format
arm64/sysreg: Rename TRBMAR_EL1 fields per auto-gen tools format
arm64/sysreg: Rename TRBSR_EL1 fields per auto-gen tools format
arm64/sysreg: Rename TRBBASER_EL1 fields per auto-gen tools format
arm64/sysreg: Rename TRBPTR_EL1 fields per auto-gen tools format
arm64/sysreg: Rename TRBLIMITR_EL1 fields per auto-gen tools format
arm64/sysreg: Convert OSECCR_EL1 to automatic generation
arm64/sysreg: Convert OSDTRTX_EL1 to automatic generation
arm64/sysreg: Convert OSDTRRX_EL1 to automatic generation
arm64/sysreg: Convert OSLAR_EL1 to automatic generation
arm64/sysreg: Standardise naming of bitfield constants in OSL[AS]R_EL1
arm64/sysreg: Convert MDSCR_EL1 to automatic register generation
...
* for-next/cpucap:
: arm64 cpucap clean-up
arm64: cpufeature: fold cpus_set_cap() into update_cpu_capabilities()
arm64: cpufeature: use cpucap naming
arm64: alternatives: use cpucap naming
arm64: standardise cpucap bitmap names
* for-next/acpi:
: Various arm64-related ACPI patches
ACPI: bus: Consolidate all arm specific initialisation into acpi_arm_init()
* for-next/kdump:
: Simplify the crashkernel reservation behaviour of crashkernel=X,high on arm64
arm64: add kdump.rst into index.rst
Documentation: add kdump.rst to present crashkernel reservation on arm64
arm64: kdump: simplify the reservation behaviour of crashkernel=,high
* for-next/acpi-doc:
: Update ACPI documentation for Arm systems
Documentation/arm64: Update ACPI tables from BBR
Documentation/arm64: Update references in arm-acpi
Documentation/arm64: Update ARM and arch reference
* for-next/doc:
: arm64 documentation updates
Documentation/arm64: Add ptdump documentation
* for-next/tpidr2-fix:
: Fix the TPIDR2_EL0 register restoring on sigreturn
kselftest/arm64: Add a test case for TPIDR2 restore
arm64/signal: Restore TPIDR2 register rather than memory state
Due to the fact that TPIDR2 is intended to be managed by libc we don't
currently test modifying it via the signal context since that might
disrupt libc's usage of it and cause instability. We can however test the
opposite case with less risk, modifying TPIDR2 in a signal handler and
making sure that the original value is restored after returning from the
signal handler. Add a test which does this.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230621-arm64-fix-tpidr2-signal-restore-v2-2-c8e8fcc10302@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add new test case kprobe_opt_types.tc which enables and checks
if each probe has been optimized in order to test potential issues with
optimized probes.
The '|| continue' is added with the echo statement to ignore errors that
are caused by trying to add kprobes to non probeable lines and continue
with the test.
Link: Link: https://lore.kernel.org/linux-trace-kernel/20230428163842.95118-3-akanksha@linux.ibm.com
Signed-off-by: Akanksha J N <akanksha@linux.ibm.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
The property of "cpu" when it has no cpu map is true on S390 with the
PMU cpum_cf. Rather than maintain a list of such PMUs, reuse the
is_core test result from the caller.
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: Thomas Richter <tmricht@linux.ibm.com>
Cc: Ravi Bangoria <ravi.bangoria@amd.com>
Cc: James Clark <james.clark@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-perf-users@vger.kernel.org
Link: https://lore.kernel.org/r/20230623043843.4080180-2-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
JSON events created in pmu-events.c by jevents.py may not specify a
PMU they are associated with, in which case it is implied that it is
the first core PMU. Care is needed to select this for regular 'cpu',
s390 'cpum_cf' and ARMs many names as at the point the name is first
needed the core PMUs list hasn't been initialized. Add a helper in
perf_pmus to create this value, in the worst case by scanning sysfs.
v2. Add missing close if fdopendir fails.
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: Thomas Richter <tmricht@linux.ibm.com>
Cc: Ravi Bangoria <ravi.bangoria@amd.com>
Cc: James Clark <james.clark@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Link: https://lore.kernel.org/r/20230623043843.4080180-1-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The result of thread__find_map is the map in the passed in
addr_location. Calling addr_location__exit puts that map and so copies
need to do a map__get. Add in the corresponding map__puts.
v2. Add missing map__put when dso is missing.
Signed-off-by: Ian Rogers <irogers@google.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ivan Babrou <ivan@cloudflare.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Link: https://lore.kernel.org/r/20230623043107.4077510-1-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The task-analyzer.py script (actually every other scripts too) requires
PERF_EXEC_PATH env to find dependent libraries and scripts. For scripts
test to run correctly, it needs to set PERF_EXEC_PATH to the perf tool
source directory.
Instead of blindly update the env, let's check the directory structure
to make sure it points to the correct location.
Fixes: e8478b84d6 ("perf test: add new task-analyzer tests")
Cc: Petar Gligoric <petar.gligoric@rohde-schwarz.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Aditya Gupta <adityag@linux.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Acked-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The buffer is used to save register mapping in a sample. Normally
perf samples don't have any register so the string should be empty.
But it missed to initialize the buffer when the size is 0. And it's
passed to PyUnicode_FromString() with a garbage data.
So it returns NULL due to invalid input (instead of an empty unicode
string object) which causes a segfault like below:
Thread 2.1 "perf" received signal SIGSEGV, Segmentation fault.
[Switching to Thread 0x7ffff7c83780 (LWP 193775)]
0x00007ffff6dbca2e in PyDict_SetItem () from /lib/x86_64-linux-gnu/libpython3.11.so.1.0
(gdb) bt
#0 0x00007ffff6dbca2e in PyDict_SetItem () from /lib/x86_64-linux-gnu/libpython3.11.so.1.0
#1 0x00007ffff6dbf848 in PyDict_SetItemString () from /lib/x86_64-linux-gnu/libpython3.11.so.1.0
#2 0x000055555575824d in pydict_set_item_string_decref (val=0x0, key=0x5555557f96e3 "iregs", dict=0x7ffff5f7f780)
at util/scripting-engines/trace-event-python.c:145
#3 set_regs_in_dict (evsel=0x555555efc370, sample=0x7fffffffb870, dict=0x7ffff5f7f780)
at util/scripting-engines/trace-event-python.c:776
#4 get_perf_sample_dict (sample=sample@entry=0x7fffffffb870, evsel=evsel@entry=0x555555efc370, al=al@entry=0x7fffffffb2e0,
addr_al=addr_al@entry=0x0, callchain=callchain@entry=0x7ffff63ef440) at util/scripting-engines/trace-event-python.c:923
#5 0x0000555555758ec1 in python_process_tracepoint (sample=0x7fffffffb870, evsel=0x555555efc370, al=0x7fffffffb2e0, addr_al=0x0)
at util/scripting-engines/trace-event-python.c:1044
#6 0x00005555555c5db8 in process_sample_event (tool=<optimized out>, event=<optimized out>, sample=<optimized out>,
evsel=0x555555efc370, machine=0x555555ef4d68) at builtin-script.c:2421
#7 0x00005555556b7793 in perf_session__deliver_event (session=0x555555ef4b60, event=0x7ffff62ff7d0, tool=0x7fffffffc150,
file_offset=30672, file_path=0x555555efb8a0 "perf.data") at util/session.c:1639
#8 0x00005555556bc864 in do_flush (show_progress=true, oe=0x555555efb700) at util/ordered-events.c:245
#9 __ordered_events__flush (oe=oe@entry=0x555555efb700, how=how@entry=OE_FLUSH__FINAL, timestamp=timestamp@entry=0)
at util/ordered-events.c:324
#10 0x00005555556bd06e in ordered_events__flush (oe=oe@entry=0x555555efb700, how=how@entry=OE_FLUSH__FINAL)
at util/ordered-events.c:342
#11 0x00005555556b9d63 in __perf_session__process_events (session=0x555555ef4b60) at util/session.c:2465
#12 perf_session__process_events (session=0x555555ef4b60) at util/session.c:2627
#13 0x00005555555cb1d0 in __cmd_script (script=0x7fffffffc150) at builtin-script.c:2839
#14 cmd_script (argc=<optimized out>, argv=<optimized out>) at builtin-script.c:4365
#15 0x0000555555650811 in run_builtin (p=p@entry=0x555555ed8948 <commands+456>, argc=argc@entry=4, argv=argv@entry=0x7fffffffe240)
at perf.c:323
#16 0x0000555555597eb3 in handle_internal_command (argv=0x7fffffffe240, argc=4) at perf.c:377
#17 run_argv (argv=<synthetic pointer>, argcp=<synthetic pointer>) at perf.c:421
#18 main (argc=4, argv=0x7fffffffe240) at perf.c:537
Fixes: 51cfe7a3e8 ("perf python: Avoid 2 leak sanitizer issues")
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Acked-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
$TEST_PROGRAM is a command with spaces so it's supposed to be word
split. The referenced fix to fix the shellcheck warnings incorrectly
quoted this string so unquote it to fix the test.
At the same time silence the shellcheck warning for that line and fix
two more shellcheck errors at the end of the script.
Fixes: 1bb17b4c6c ("perf tests arm_callgraph_fp: Address shellcheck warnings about signal names and adding double quotes for expression")
Signed-off-by: James Clark <james.clark@arm.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Rogers <irogers@google.com>
Cc: spoorts2@in.ibm.com
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Link: https://lore.kernel.org/r/20230622101809.2431897-1-james.clark@arm.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Przemek suggests that I shouldn't accuse GCC of witchcraft,
there is a simpler explanation for why we need manual define.
scripts/headers_install.sh modifies the guard, removing _UAPI.
That's why including a kernel header from the tree and from
/usr leads to duplicate definitions.
This also solves the mystery of why I needed to include
the header conditionally. I had the wrong guards for most
cases but ethtool.
Suggested-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/20230621231719.2728928-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mptcp and netfilter.
Current release - regressions:
- netfilter: add NFT_TRANS_PREPARE_ERROR to deal with bound set/chain
- eth: mlx5e:
- fix scheduling of IPsec ASO query while in atomic
- free IRQ rmap and notifier on kernel shutdown
Current release - new code bugs:
- phy: manual remove LEDs to ensure correct ordering
Previous releases - regressions:
- mptcp: fix possible divide by zero in recvmsg()
- dsa: revert "net: phy: dp83867: perform soft reset and retain established link"
Previous releases - always broken:
- sched: netem: acquire qdisc lock in netem_change()
- bpf:
- fix verifier id tracking of scalars on spill
- fix NULL dereference on exceptions
- accept function names that contain dots
- netfilter: disallow element updates of bound anonymous sets
- mptcp: ensure listener is unhashed before updating the sk status
- xfrm:
- add missed call to delete offloaded policies
- fix inbound ipv4/udp/esp packets to UDPv6 dualstack sockets
- selftests: fixes for FIPS mode
- dsa: mt7530: fix multiple CPU ports, BPDU and LLDP handling
- eth: sfc: use budget for TX completions
Misc:
- wifi: iwlwifi: add support for SO-F device with PCI id 0x7AF0
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEEg1AjqC77wbdLX2LbKSR5jcyPE6QFAmSUZO0SHHBhYmVuaUBy
ZWRoYXQuY29tAAoJECkkeY3MjxOkBjAP/RfTUYdlPqz9jSvz0HmQt2Er39HyVb9I
pzEpJSQGfO+eyIrlxmleu8cAaW5HdvyfMcBgr04uh+Jf06s+VJrD95IO9zDHHKoC
86itYNKMS3fSt1ivzg49i5uq66MhjtAcfIOB9HMOAQ2Jd+DYlzyWOOHw28ZAxsBZ
Q6TU97YEMuU4FdLkoKob1aVswC5cPxNx2IH9NagfbtijaYZqeN9ZX9EI5yMUyH8f
5gboqOhXUQK0MQLM5TFySHeoayyQ+tRBz24nF0/6lWiRr+xzMTEKdkFpRza7Mxzj
S8NxN3C+zOf96gic6kYOXmM6y0sOlbwC9JoeWTp8Tuh6DEYi6xLC2XkiYJ51idZg
PElgRpkM1ddqvvFWFgZlNik5z0vbGnJH7pt0VuOSNntxE60cdQwvWEOr09vvPcS5
0nMVD0uc8pds2h4hit+sdLltcVnOgoNUYr1/sI6oydofa1BrLnhFPF7z/gUs9foD
NuCchiaBF11yBGKufcNBNEB4w35g3Kcu6TGhHb168OJi+UnSnwlI0Ccw7iO10pkv
RjefhR60+wZC6+leo57nZeYqaLQJuALY0QYFsyeM+T0MGSYkbH24CmbNdSmO4MRr
+VX2CwIqeIds4Hx31o0Feu+FaJqXw46/2nrSDxel/hlCJnGSMXZTw+b/4pFEHLP+
l71ijZpJqV1S
=GH2b
-----END PGP SIGNATURE-----
Merge tag 'net-6.4-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from ipsec, bpf, mptcp and netfilter.
Current release - regressions:
- netfilter: add NFT_TRANS_PREPARE_ERROR to deal with bound set/chain
- eth: mlx5e:
- fix scheduling of IPsec ASO query while in atomic
- free IRQ rmap and notifier on kernel shutdown
Current release - new code bugs:
- phy: manual remove LEDs to ensure correct ordering
Previous releases - regressions:
- mptcp: fix possible divide by zero in recvmsg()
- dsa: revert "net: phy: dp83867: perform soft reset and retain
established link"
Previous releases - always broken:
- sched: netem: acquire qdisc lock in netem_change()
- bpf:
- fix verifier id tracking of scalars on spill
- fix NULL dereference on exceptions
- accept function names that contain dots
- netfilter: disallow element updates of bound anonymous sets
- mptcp: ensure listener is unhashed before updating the sk status
- xfrm:
- add missed call to delete offloaded policies
- fix inbound ipv4/udp/esp packets to UDPv6 dualstack sockets
- selftests: fixes for FIPS mode
- dsa: mt7530: fix multiple CPU ports, BPDU and LLDP handling
- eth: sfc: use budget for TX completions
Misc:
- wifi: iwlwifi: add support for SO-F device with PCI id 0x7AF0"
* tag 'net-6.4-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (74 commits)
revert "net: align SO_RCVMARK required privileges with SO_MARK"
net: wwan: iosm: Convert single instance struct member to flexible array
sch_netem: acquire qdisc lock in netem_change()
selftests: forwarding: Fix race condition in mirror installation
wifi: mac80211: report all unusable beacon frames
mptcp: ensure listener is unhashed before updating the sk status
mptcp: drop legacy code around RX EOF
mptcp: consolidate fallback and non fallback state machine
mptcp: fix possible list corruption on passive MPJ
mptcp: fix possible divide by zero in recvmsg()
mptcp: handle correctly disconnect() failures
bpf: Force kprobe multi expected_attach_type for kprobe_multi link
bpf/btf: Accept function names that contain dots
Revert "net: phy: dp83867: perform soft reset and retain established link"
net: mdio: fix the wrong parameters
netfilter: nf_tables: Fix for deleting base chains with payload
netfilter: nfnetlink_osf: fix module autoload
netfilter: nf_tables: drop module reference after updating chain
netfilter: nf_tables: disallow timeout for anonymous sets
netfilter: nf_tables: disallow updates of anonymous sets
...
We can see the following definitions in bfd/elfnn-loongarch.c:
#define PLT_HEADER_INSNS 8
#define PLT_HEADER_SIZE (PLT_HEADER_INSNS * 4)
#define PLT_ENTRY_INSNS 4
#define PLT_ENTRY_SIZE (PLT_ENTRY_INSNS * 4)
so plt header size is 32 and plt entry size is 16 on LoongArch,
let us add LoongArch case in get_plt_sizes().
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: loongarch@lists.linux.dev
Cc: loongson-kernel@lists.loongnix.cn
Cc: Ingo Molnar <mingo@redhat.com>
Link: https://sourceware.org/git/?p=binutils-gdb.git;a=blob;f=bfd/elfnn-loongarch.c
Link: https://lore.kernel.org/r/1684835873-15956-1-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The commit fc51fc87b1 factored out the helper functions to a library
but the new file had execute permission. Due to the way it detects
the shell test scripts, it showed up in the perf test list unexpectedly.
$ ./perf test list 2>&1 | grep 86
76: x86 bp modify
77: x86 Sample parsing
78: x86 hybrid
86: <---- (here)
$ ./perf test -v 86
86: :
--- start ---
test child forked, pid 1932207
test child finished with 0
---- end ----
: Ok
As it's a collection of library functions, it should not run as is.
Let's remove the execute permission.
Fixes: fc51fc87b1 ("perf test: Move all the check functions of stat CSV output to lib")
Acked-by: Ian Rogers <irogers@google.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230622055832.83476-1-namhyung@kernel.org
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Source file locations for syscall definitions can change over a period
of time. File paths in comments get stale and are hard to maintain long
term. Also, their usefulness is questionable since it would be easier to
locate a syscall definition using the SYSCALL_DEFINEx() macro.
Remove all source file path comments from the syscall headers. Also,
equalize the uneven line spacing (some of which is introduced due to the
deletions).
Signed-off-by: Sohil Mehta <sohil.mehta@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
After the following two commits:
commit 872e24d5c6 ("hexagon: remove asm/bitsperlong.h")
commit 83f0124ad8 ("microblaze: remove asm-generic wrapper headers")
the arch-specific headers of hexagon and microblaze have been removed,
the tools arch uapi headers are useless too, remove them.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now we specify the minimal version of GCC as 5.1 and Clang/LLVM as 11.0.0
in Documentation/process/changes.rst, __CHAR_BIT__ and __SIZEOF_LONG__ are
usable, it is probably fine to unify the definition of __BITS_PER_LONG as
(__CHAR_BIT__ * __SIZEOF_LONG__) in asm-generic uapi bitsperlong.h.
In order to keep safe and avoid regression, only unify uapi bitsperlong.h
for some archs such as arm64, riscv and loongarch which are using newer
toolchains that have the definitions of __CHAR_BIT__ and __SIZEOF_LONG__.
Suggested-by: Xi Ruoyao <xry111@xry111.site>
Link: https://lore.kernel.org/all/d3e255e4746de44c9903c4433616d44ffcf18d1b.camel@xry111.site/
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/linux-arch/a3a4f48a-07d4-4ed9-bc53-5d383428bdd2@app.fastmail.com/
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When building the latest kernel/selftest with clang17 compiler:
make LLVM=1 -j <== for kernel
make -C tools/testing/selftests/bpf LLVM=1 -j <== for selftest
I hit the following compilation error:
[...]
In file included from progs/vrf_socket_lookup.c:3:
In file included from /usr/include/linux/ip.h:21:
In file included from /usr/include/asm/byteorder.h:5:
In file included from /usr/include/linux/byteorder/little_endian.h:13:
/usr/include/linux/swab.h:136:8: error: unknown type name '__always_inline'
136 | static __always_inline unsigned long __swab(const unsigned long y)
| ^
/usr/include/linux/swab.h:171:8: error: unknown type name '__always_inline'
171 | static __always_inline __u16 __swab16p(const __u16 *p)
| ^
/usr/include/linux/swab.h:171:29: error: expected ';' after top level declarator
171 | static __always_inline __u16 __swab16p(const __u16 *p)
| ^
[...]
Basically, with header files in my local host which is based on 5.12 kernel,
__always_inline is not defined and this caused compilation failure.
Since __always_inline is defined in bpf_helpers.h, let us move bpf_helpers.h
to an early position which fixed the problem.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230622061921.816772-1-yhs@fb.com
When mirroring to a gretap in hardware the device expects to be
programmed with the egress port and all the encapsulating headers. This
requires the driver to resolve the path the packet will take in the
software data path and program the device accordingly.
If the path cannot be resolved (in this case because of an unresolved
neighbor), then mirror installation fails until the path is resolved.
This results in a race that causes the test to sometimes fail.
Fix this by setting the neighbor's state to permanent in a couple of
tests, so that it is always valid.
Fixes: 35c31d5c32 ("selftests: forwarding: Test mirror-to-gretap w/ UL 802.1d")
Fixes: 239e754af8 ("selftests: forwarding: Test mirror-to-gretap w/ UL 802.1q")
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/268816ac729cb6028c7a34d4dda6f4ec7af55333.1687264607.git.petrm@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the MPTCP MIB counters introduced in commit fc518953bc
("mptcp: add and use MIB counter infrastructure") and more later. The
MPTCP Join selftest heavily relies on these counters.
If a counter is not supported by the kernel, it is not displayed when
using 'nstat -z'. We can then detect that and skip the verification. A
new helper (get_counter()) has been added recently in the -net tree to
do the required checks and return an error if the counter is not
available.
This commit is similar to the one with the same title applied in the
-net tree but it modifies code only present in net-next for the moment,
see the Fixes commit below.
While at it, we can also remove the use of ${extra_msg} variable which
is never assigned in chk_rm_tx_nr() function and use 'echo' without '-n'
parameter.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 0639fa230a ("selftests: mptcp: add explicit check for new mibs")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update the existing sockopt test-case to do some basic checks
on the newly added counters.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/385
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rerun failed metrics with longer workload to avoid false failure because
sometimes metric value test fails when running in very short amount of
time. Skip rerun if equal to or more than 20 metrics fail.
Signed-off-by: Weilin Wang <weilin.wang@intel.com>
Tested-by: Namhyung Kim <namhyung@kernel.org>
Cc: ravi.bangoria@amd.com
Cc: Ian Rogers <irogers@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Caleb Biggers <caleb.biggers@intel.com>
Cc: Perry Taylor <perry.taylor@intel.com>
Cc: Samantha Alt <samantha.alt@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Link: https://lore.kernel.org/r/20230620170027.1861012-4-weilin.wang@intel.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Add skip list for metrics known would fail because some of the metrics are
very likely to fail due to multiplexing or other errors. So add all of the
flaky tests into the skip list.
Signed-off-by: Weilin Wang <weilin.wang@intel.com>
Tested-by: Namhyung Kim <namhyung@kernel.org>
Cc: ravi.bangoria@amd.com
Cc: Ian Rogers <irogers@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Caleb Biggers <caleb.biggers@intel.com>
Cc: Perry Taylor <perry.taylor@intel.com>
Cc: Samantha Alt <samantha.alt@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Link: https://lore.kernel.org/r/20230620170027.1861012-3-weilin.wang@intel.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Add metric value validation test to check if metric values are with in
correct value ranges. There are three types of tests included: 1)
positive-value test checks if all the metrics collected are non-negative;
2) single-value test checks if the list of metrics have values in given
value ranges; 3) relationship test checks if multiple metrics follow a
given relationship, e.g. memory_bandwidth_read + memory_bandwidth_write =
memory_bandwidth_total.
Signed-off-by: Weilin Wang <weilin.wang@intel.com>
Tested-by: Namhyung Kim <namhyung@kernel.org>
Cc: ravi.bangoria@amd.com
Cc: Ian Rogers <irogers@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Caleb Biggers <caleb.biggers@intel.com>
Cc: Perry Taylor <perry.taylor@intel.com>
Cc: Samantha Alt <samantha.alt@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Link: https://lore.kernel.org/r/20230620170027.1861012-2-weilin.wang@intel.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Add the test for additional reference to chains that are explicitly
created by RTM_NEWCHAIN message.
The test result:
1..1
ok 1 c2b4 - soft lockup alarm will be not generated after delete the prio 0
filter of the chain
This is a follow up to commit c9a82bec02 ("net/sched: cls_api: Fix lockup on flushing explicitly created chain").
Signed-off-by: Mingshuai Ren <renmingshuai@huawei.com>
Acked-by: Pedro Tammela <pctammela@mojatatu.com>
Acked-by: Victor Nogueira <victor@mojatatu.com>
Link: https://lore.kernel.org/r/20230620014939.2034054-1-renmingshuai@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Verify that socket lookup via TC/XDP with all BPF APIs is VRF aware.
Signed-off-by: Gilad Sever <gilad9366@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Eyal Birger <eyal.birger@gmail.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20230621104211.301902-5-gilad9366@gmail.com
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.
The bridge eventually inherits MAC address from its first member, after the
enslavement is acked. A number of (mainly VXLAN) selftests already work
around the problem by setting the MAC address to whatever it will
eventually be anyway. Do the same for this selftest.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge (this holds
for all bridges used here), the bridge MAC address does not have the same
prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all
the RIFs have to have the same 38-bit MAC address prefix. Since the bridge
does not obey this limitation, the RIF cannot be created, and the
enslavement attempt is vetoed on the grounds of the configuration not being
offloadable.
The selftest itself however checks various aspects of VXLAN offloading and
the bridges do not need to participate in routing traffic. The IP addresses
or the RIFs are irrelevant.
Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridges in this selftest, thus exempting them from mlxsw router attention.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.
The selftest itself however checks vetoing of a different aspect of the
configuration and the bridge does not need to participate in routing
traffic. The IP address or the RIF are irrelevant.
Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridge in this selftest, thus exempting it from mlxsw router attention.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge (this holds
for both bridges used here), the bridge MAC address does not have the same
prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all
the RIFs have to have the same 38-bit MAC address prefix. Since the bridge
does not obey this limitation, the RIF cannot be created, and the
enslavement attempt is vetoed on the grounds of the configuration not being
offloadable.
The selftest itself however checks traffic prioritization and scheduling,
and the bridges serve for their L2 forwarding capabilities, and do not need
to participate in routing traffic. The IP addresses or the RIFs are
irrelevant.
Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridges in this selftest, thus exempting them from mlxsw router attention.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge (this holds
for both bridges used here), the bridge MAC address does not have the same
prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all
the RIFs have to have the same 38-bit MAC address prefix. Since the bridge
does not obey this limitation, the RIF cannot be created, and the
enslavement attempt is vetoed on the grounds of the configuration not being
offloadable.
The selftest itself however checks traffic prioritization and scheduling,
and the bridges serve for their L2 forwarding capabilities, and do not need
to participate in routing traffic. The IP addresses or the RIFs are
irrelevant.
Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridges in this selftest, thus exempting them from mlxsw router attention.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.
The selftest itself however checks DCB DSCP-based prioritization, and the
bridge serves for its L2 forwarding capabilities, and does not need to
participate in routing traffic. The IP address or the RIF are irrelevant.
Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridge in this selftest, thus exempting it from mlxsw router attention.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.
The selftest itself however checks how many mirroring sessions a machine is
capable of offloading. The IP address or the RIF are irrelevant.
Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridge in this selftest, thus exempting it from mlxsw router attention.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge (this holds
for all bridges used here), the bridge MAC address does not have the same
prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all
the RIFs have to have the same 38-bit MAC address prefix. Since the bridge
does not obey this limitation, the RIF cannot be created, and the
enslavement attempt is vetoed on the grounds of the configuration not being
offloadable.
The selftest itself however checks whether a different vetoed aspect of the
configuration provides an extack. The IP address or the RIF are irrelevant.
Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridges in this selftest, thus exempting them from mlxsw router attention.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
The swp enslavement to the 802.1ad bridge is not allowed, because RIFs are
not allowed to be created for 802.1ad bridges, but the address indicates
one needs to be created. Thus the veto selftests fail already during the
port enslavement. Then the attempt to create a VLAN on top of the same
bridge is not vetoed, because the bridge is not related to mlxsw, and the
selftest fails.
Fix by disabling automatic IPv6 address generation for the bridges in this
selftest, thus exempting them from the mlxsw router attention.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.
The bridge eventually inherits MAC address from its first member, after the
enslavement is acked. A number of (mainly VXLAN) selftests already work
around the problem by setting the MAC address to whatever it will
eventually be anyway. Do the same here.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.
The bridge eventually inherits MAC address from its first member, after the
enslavement is acked. A number of (mainly VXLAN) selftests already work
around the problem by setting the MAC address to whatever it will
eventually be anyway. Do the same for several mirror_gre selftests.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.
These two selftests however check mirroring traffic to a gretap netdevice.
The bridge here does not participate in routing traffic and the IP address
or the RIF are irrelevant.
Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridges in these selftests, thus exempting them from mlxsw router
attention. Since the bridges are only used for L2 forwarding, this change
should not hinder usefulness of this selftest for testing SW datapath or HW
datapaths in other devices.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.
The selftest itself however checks whether skbedit changes packet priority
as appropriate. The bridge thus does not need to participate in routing
traffic and the IP address or the RIF are irrelevant.
Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridge in this selftest, thus exempting it from mlxsw router attention.
Since the bridge is only used for L2 forwarding, this change should not
hinder usefulness of this selftest for testing SW datapath or HW datapaths
in other devices.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.
The selftest itself however checks operation of pedit on IPv4 and IPv6
dsfield and its parts. The bridge thus does not need to participate in
routing traffic and the IP address or the RIF are irrelevant.
Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridge in this selftest, thus exempting it from mlxsw router attention.
Since the bridge is only used for L2 forwarding, this change should not
hinder usefulness of this selftest for testing SW datapath or HW datapaths
in other devices.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
This will cause this selftest to fail spuriously. The swp enslavement to
the 802.1ad bridge is not allowed, because RIFs are not allowed to be
created for 802.1ad bridges, but the address indicates one needs to be
created.
Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridge in this selftest, thus exempting it from mlxsw router attention.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
This will cause this selftest to fail spuriously. The swp enslavement to
the 802.1ad bridge is not allowed, because RIFs are not allowed to be
created for 802.1ad bridges, but the address indicates one needs to be
created.
Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridge in this selftest, thus exempting it from mlxsw router attention.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCZJK5DwAKCRDbK58LschI
gyUtAQD4gT4BEVHRqvniw9yyqYo0BvElAznutDq7o9kFHFep2gEAoksEWS84OdZj
0L5mSKjXrpHKzmY/jlMrVIcTb3VzOw0=
=gAYE
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2023-06-21
We've added 7 non-merge commits during the last 14 day(s) which contain
a total of 7 files changed, 181 insertions(+), 15 deletions(-).
The main changes are:
1) Fix a verifier id tracking issue with scalars upon spill,
from Maxim Mikityanskiy.
2) Fix NULL dereference if an exception is generated while a BPF
subprogram is running, from Krister Johansen.
3) Fix a BTF verification failure when compiling kernel with LLVM_IAS=0,
from Florent Revest.
4) Fix expected_attach_type enforcement for kprobe_multi link,
from Jiri Olsa.
5) Fix a bpf_jit_dump issue for x86_64 to pick the correct JITed image,
from Yonghong Song.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Force kprobe multi expected_attach_type for kprobe_multi link
bpf/btf: Accept function names that contain dots
selftests/bpf: add a test for subprogram extables
bpf: ensure main program has an extable
bpf: Fix a bpf_jit_dump issue for x86_64 with sysctl bpf_jit_enable.
selftests/bpf: Add test cases to assert proper ID tracking on spill
bpf: Fix verifier id tracking of scalars on spill
====================
Link: https://lore.kernel.org/r/20230621101116.16122-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The arm64 documentation has moved under Documentation/arch/. Fix up a
dangling reference to match.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Fixes an issue where an incorrect filename was added in the DWARF line table of
an ELF object file when calling 'perf inject --jit' due to not checking the
filename of a debug entry against the repeated name marker (/xff/0).
The marker is mentioned in the tools/perf/util/jitdump.h header, which describes
the jitdump binary format, and indicitates that the filename in a debug entry
is the same as the previous enrty.
In the function emit_lineno_info(), in the file tools/perf/util/genelf-debug.c,
the debug entry filename gets compared to the previous entry filename. If they
are not the same, a new filename is added to the DWARF line table. However,
since there is no check against '\xff\0', in some cases '\xff\0' is inserted
as the filename into the DWARF line table.
This can be seen with `objdump --dwarf=line` on the ELF file after `perf inject --jit`.
It also makes no source code information show up in 'perf annotate'.
Signed-off-by: Elisabeth Panholzer <elisabeth@leaningtech.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20230602123815.255001-1-paniii94@gmail.com
[ Fixed a trailing white space, removed a subject prefix ]
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
This includes a wholesale reversion of the post-6.4 series "make slab shrink
lockless". After input from Dave Chinner it has been decided that we
should go a different way. Thread starts at
https://lkml.kernel.org/r/ZH6K0McWBeCjaf16@dread.disaster.area.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZJH/qAAKCRDdBJ7gKXxA
jq7uAP9AtDGHfvOuW5jlHdYfpUBnbfuQDKjiik71UuIxyhtwQQEAqpOBv7UDuhHj
NbNIGTIi/xM5vkpjV6CBo9ymR7qTKwo=
=uGuc
-----END PGP SIGNATURE-----
Merge tag 'mm-hotfixes-stable-2023-06-20-12-31' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull hotfixes from Andrew Morton:
"19 hotfixes. 8 of these are cc:stable.
This includes a wholesale reversion of the post-6.4 series 'make slab
shrink lockless'. After input from Dave Chinner it has been decided
that we should go a different way [1]"
Link: https://lkml.kernel.org/r/ZH6K0McWBeCjaf16@dread.disaster.area [1]
* tag 'mm-hotfixes-stable-2023-06-20-12-31' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
selftests/mm: fix cross compilation with LLVM
mailmap: add entries for Ben Dooks
nilfs2: prevent general protection fault in nilfs_clear_dirty_page()
Revert "mm: vmscan: make global slab shrink lockless"
Revert "mm: vmscan: make memcg slab shrink lockless"
Revert "mm: vmscan: add shrinker_srcu_generation"
Revert "mm: shrinkers: make count and scan in shrinker debugfs lockless"
Revert "mm: vmscan: hold write lock to reparent shrinker nr_deferred"
Revert "mm: vmscan: remove shrinker_rwsem from synchronize_shrinkers()"
Revert "mm: shrinkers: convert shrinker_rwsem to mutex"
nilfs2: fix buffer corruption due to concurrent device reads
scripts/gdb: fix SB_* constants parsing
scripts: fix the gfp flags header path in gfp-translate
udmabuf: revert 'Add support for mapping hugepages (v4)'
mm/khugepaged: fix iteration in collapse_file
memfd: check for non-NULL file_seals in memfd_create() syscall
mm/vmalloc: do not output a spurious warning when huge vmalloc() fails
mm/mprotect: fix do_mprotect_pkey() limit check
writeback: fix dereferencing NULL mapping->host on writeback_page_template
Remove the "struct mutex lock" variable from annotation that is
allocated per symbol. This removes in the region of 40 bytes per
symbol allocation. Use a sharded mutex where the number of shards is
set to the number of CPUs. Assuming good hashing of the annotation
(done based on the pointer), this means in order to contend there
needs to be more threads than CPUs, which is not currently true in any
perf command. Were contention an issue it is straightforward to
increase the number of shards in the mutex.
On my Debian/glibc based machine, this reduces the size of struct
annotation from 136 bytes to 96 bytes, or nearly 30%.
Signed-off-by: Ian Rogers <irogers@google.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Andres Freund <andres@anarazel.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Yuan Can <yuancan@huawei.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Link: https://lore.kernel.org/r/20230615040715.2064350-2-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Per object mutexes may come with significant memory cost while a
global mutex can suffer from unnecessary contention. A sharded mutex
is a compromise where objects are hashed and then a particular mutex
for the hash of the object used. Contention can be controlled by the
number of shards.
v2. Use hashmap.h's hash_bits in case of contention from alignment of
objects.
Signed-off-by: Ian Rogers <irogers@google.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Andres Freund <andres@anarazel.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Yuan Can <yuancan@huawei.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Link: https://lore.kernel.org/r/20230615040715.2064350-1-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
What we need to calculate is the size of the object, not the size of the
pointer.
Fixed: 51cfe7a3e8 ("perf python: Avoid 2 leak sanitizer issues")
Signed-off-by: Li Dong <lidong@vivo.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Sean Christopherson <seanjc@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: opensource.kernel@vivo.com
Link: https://lore.kernel.org/r/20230619082036.410-1-lidong@vivo.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The malloc() function may return NULL when it fails,
which may cause null pointer deference in add_cmdname(),
add Null check for return value of malloc().
Found by our static analysis tool.
Signed-off-by: Chenyuan Mi <cymi20@fudan.edu.cn>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20230614150118.115208-1-cymi20@fudan.edu.cn
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The newline is missing for error messages in add_default_attributes()
Before:
# perf stat --topdown
Topdown requested but the topdown metric groups aren't present.
(See perf list the metric groups have names like TopdownL1)#
After:
# perf stat --topdown
Topdown requested but the topdown metric groups aren't present.
(See perf list the metric groups have names like TopdownL1)
#
In addition, perf_stat_init_aggr_mode() and perf_stat_init_aggr_mode_file()
have the same problem, fixed by the way.
Signed-off-by: Yang Jihong <yangjihong1@huawei.com>
Acked-by: Ian Rogers <irogers@google.com>
Reviewed-by: James Clark <james.clark@arm.com>
Link: https://lore.kernel.org/r/20230614021505.59856-1-yangjihong1@huawei.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
- Fix MAINTAINERS file to point to proper mailing list for rtla and rv
The mailing list pointed to linux-trace-devel instead of
linux-trace-kernel. The former is for the tracing libraries
and the latter is for anything in the Linux kernel tree.
The wrong mailing list was used because linux-trace-kernel did not
exist when rtla and rv were created.
- User events:
. Fix matching of dynamic events to their user events
When user writes to dynamic_events file, a lookup of the
registered dynamic events are made, but there were some cases
that a match could be incorrectly made.
. Add auto cleanup of user events
Have the user events automatically get removed when the last
reference (file descriptor) is closed. This was asked for to
prevent leaks of user events hanging around needing admins
to clean them up.
. Add persistent logic (but not let user space use it yet)
In some cases, having a persistent user event (one that does not
get cleaned up automatically) is useful. But there's still
debates about how to expose this to user space. The infrastructure
is added, but the API is not.
. Update the selftests
Update the user event selftests to reflect the above changes.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCZJGrABQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qgRDAQDvF8ktlcn+gqyUxt2OcTlbBh0jqS0b
FKXYdq6FTgfWYQD/ctunFbPdzn4D6Kc/lG8p4QxpMmtA19BUOPwEt3CkAwM=
=CDzr
-----END PGP SIGNATURE-----
Merge tag 'trace-v6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Fix MAINTAINERS file to point to proper mailing list for rtla and rv
The mailing list pointed to linux-trace-devel instead of
linux-trace-kernel. The former is for the tracing libraries and the
latter is for anything in the Linux kernel tree. The wrong mailing
list was used because linux-trace-kernel did not exist when rtla and
rv were created.
- User events:
- Fix matching of dynamic events to their user events
When user writes to dynamic_events file, a lookup of the
registered dynamic events is made, but there were some cases that
a match could be incorrectly made.
- Add auto cleanup of user events
Have the user events automatically get removed when the last
reference (file descriptor) is closed. This was asked for to
prevent leaks of user events hanging around needing admins to
clean them up.
- Add persistent logic (but not let user space use it yet)
In some cases, having a persistent user event (one that does not
get cleaned up automatically) is useful. But there's still debates
about how to expose this to user space. The infrastructure is
added, but the API is not.
- Update the selftests
Update the user event selftests to reflect the above changes"
* tag 'trace-v6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing/user_events: Document auto-cleanup and remove dyn_event refs
selftests/user_events: Adapt dyn_test to non-persist events
selftests/user_events: Ensure auto cleanup works as expected
tracing/user_events: Add auto cleanup and future persist flag
tracing/user_events: Track refcount consistently via put/get
tracing/user_events: Store register flags on events
tracing/user_events: Remove user_ns walk for groups
selftests/user_events: Add perf self-test for empty arguments events
selftests/user_events: Clear the events after perf self-test
selftests/user_events: Add ftrace self-test for empty arguments events
tracing/user_events: Fix the incorrect trace record for empty arguments events
tracing: Modify print_fields() for fields output order
tracing/user_events: Handle matching arguments that is null from dyn_events
tracing/user_events: Prevent same name but different args event
tracing/rv/rtla: Update MAINTAINERS file to point to proper mailing list
Enables advertisement of the maximum offset supported by the phase control
functionality of PHCs. The callback is used to return an error if an offset
not supported by the PHC is used in ADJ_OFFSET. The ioctls
PTP_CLOCK_GETCAPS and PTP_CLOCK_GETCAPS2 now advertise the maximum offset a
PHC's phase control functionality is capable of supporting. Introduce new
sysfs node, max_phase_adjustment.
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Maciek Machnikowski <maciek@machnikowski.net>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Invoke clock_adjtime syscall with tx.modes set with ADJ_OFFSET when testptp
is invoked with a phase adjustment offset value. Support seconds and
nanoseconds for the offset value.
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Maciek Machnikowski <maciek@machnikowski.net>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use existing NSEC_PER_SEC declaration in place of hardcoded magic numbers.
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Maciek Machnikowski <maciek@machnikowski.net>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove all defines which aren't needed after correctly including the
kernel header files.
Link: https://lkml.kernel.org/r/20230612095347.996335-2-usama.anjum@collabora.com
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stefan Roesch <shr@devkernel.io>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
It is wrong to include unprocessed user header files directly. They are
processed to "<source_tree>/usr/include" by running "make headers" and
they are included in selftests by kselftest makefiles automatically with
help of KHDR_INCLUDES variable. These headers should always bulilt first
before building kselftests.
Link: https://lkml.kernel.org/r/20230612095347.996335-1-usama.anjum@collabora.com
Fixes: 07115fcc15 ("selftests/mm: add new selftests for KSM")
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stefan Roesch <shr@devkernel.io>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Building and running the subsuite 'damon' of kselftest, shows the
following issues:
selftests: damon: debugfs_attrs.sh
/sys/kernel/debug/damon not found
By creating a config file enabling DAMON fragments in the
selftests/damon/ directory the tests pass.
Link: https://lkml.kernel.org/r/20230412092854.3306197-1-anders.roxell@linaro.org
Fixes: b348eb7abd ("mm/damon: add user space selftests")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reviewed-by: SeongJae Park <sj@kernel.org>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
As per a discussion with Muhammad Usama Anjum [1], the following is how
one is supposed to build selftests:
make headers && make -C tools/testing/selftests/mm
Change the selftest build system's lib.mk to fail out with a helpful
message if that prerequisite "make headers" has not been done yet.
[1] https://lore.kernel.org/all/bf910fa5-0c96-3707-cce4-5bcc656b6274@collabora.com/
[jhubbard@nvidia.com: abort the make process the first time headers aren't detected]
Link: https://lkml.kernel.org/r/14573e7e-f2ad-ff34-dfbd-3efdebee51ed@nvidia.com
[anders.roxell@linaro.org: fix out-of-tree builds]
Link: https://lkml.kernel.org/r/20230613074931.666966-1-anders.roxell@linaro.org
Link: https://lkml.kernel.org/r/20230606071637.267103-12-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
There are only three uffd*() routines that are used outside of the uffd
selftests. Leave these in vm_util.c, where they are available to any mm
selftest program:
uffd_register()
uffd_unregister()
uffd_register_with_ioctls().
A few other uffd*() routines, however, are only used by the uffd-focused
tests found in uffd-stress.c and uffd-unit-tests.c. Move those routines
into uffd-common.c.
Link: https://lkml.kernel.org/r/20230606071637.267103-10-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: David Hildenbrand <david@redhat.com>
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
MADV_PAGEOUT, MADV_POPULATE_READ, MADV_COLLAPSE are conditionally
defined as necessary. However, that was being done in .c files, and a
new build failure came up that would have been automatically avoided had
these been in a common header file.
So consolidate and move them all to vm_util.h, which fixes the build
failure.
An alternative approach from Muhammad Usama Anjum was: rely on "make
headers" being required, and include asm-generic/mman-common.h. This
works in the sense that it builds, but it still generates warnings about
duplicate MADV_* symbols, and the goal here is to get a fully clean (no
warnings) build here.
Link: https://lkml.kernel.org/r/20230606071637.267103-9-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This fixes a real bug, too, because xstate_size() was assuming that
the stack variable xstate_size was initialized to zero. That's not
guaranteed nor even especially likely.
Link: https://lkml.kernel.org/r/20230606071637.267103-8-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The uffd tests generate two compile time warnings from clang's
-Wformat-security setting. These trigger at the call sites for
uffd_test_start() and uffd_test_skip().
1) Fix the uffd_test_start() issue by removing the intermediate
test_name variable (thanks to David Hildenbrand for showing how to do
this).
2) Fix the uffd_test_skip() issue by observing that there is no need for
a macro and a variable args approach, because all callers of
uffd_test_skip() pass in a simple char* string, without any format
specifiers. So just change uffd_test_skip() into a regular C function.
Link: https://lkml.kernel.org/r/20230606071637.267103-7-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
These new build products were left out of .gitignore, so add them now.
Link: https://lkml.kernel.org/r/20230606071637.267103-6-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
We cannot depend upon git to reliably retain the executable bit on shell
scripts, or so I was told several years ago while working on this same
run_vmtests.sh script. And sure enough, things such as test_hmm.sh are
lately failing to run, due to lacking execute permissions.
Fix this by explicitly adding "bash" to each of the shell script
invocations. Leave fixing the overall approach to another day.
Link: https://lkml.kernel.org/r/20230606071637.267103-5-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: David Hildenbrand <david@redhat.com>
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The stop variable is a char*, and the code was assigning a char value to
it. This was generating a warning when compiling with clang.
However, as both David and Peter pointed out, stop is not even used
after the problematic assignment to a char type. So just delete that
line entirely.
Link: https://lkml.kernel.org/r/20230606071637.267103-4-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Dummy variables are required in order to make these two (similar)
routines work, so in both cases, declare the variables as volatile in
order to avoid the clang compiler warning.
Furthermore, in order to ensure that each test actually does what is
intended, add an asm volatile invocation (thanks to David Hildenbrand
for the suggestion), with a clarifying comment so that it survives
future maintenance.
Link: https://lkml.kernel.org/r/20230606071637.267103-3-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "A minor flurry of selftest/mm fixes", v3.
A series that fixes up build errors and warnings for at least the 64-bit
builds on x86 with clang.
The series also includes an optional "improvement" of moving some uffd
code into uffd-common.[ch], which is proving to be somewhat controversial,
and so if that doesn't get resolved, then patches 9 and 10 may just get
dropped. They are not required in order to get a clean build, now that
"make headers" is happening.
[1]: https://lore.kernel.org/all/20230602013358.900637-1-jhubbard@nvidia.com/
This patch (of 11):
uffd_minor_feature() was unused. Remove it in order to fix the associated
clang build warning.
Link: https://lkml.kernel.org/r/20230606071637.267103-1-jhubbard@nvidia.com
Link: https://lkml.kernel.org/r/20230606071637.267103-2-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Considering that only bench_ringbufs.c supports consumer, just set the
default value of consumer_cnt as 0. After that, update the validity
check of consumer_cnt, remove unused consumer_thread code snippets and
set consumer_cnt as 1 in run_bench_ringbufs.sh accordingly.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20230613080921.1623219-5-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When using option -a without --prod-affinity or --cons-affinity, if the
number of producers and consumers is greater than the number of online
CPUs, the benchmark will fail to run as shown below:
$ getconf _NPROCESSORS_ONLN
8
$ ./bench bpf-loop -a -p9
Setting up benchmark 'bpf-loop'...
setting affinity to CPU #8 failed: -22
Fix it by returning the remainder of next_cpu divided by the number of
online CPUs in next_cpu().
Signed-off-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20230613080921.1623219-4-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The return value of pthread API is the error code when the called
API fails, so output the return value instead of errno.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20230613080921.1623219-3-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Currently the MM selftests attempt to work out the target architecture by
using CROSS_COMPILE or otherwise querying the host machine, storing the
target architecture in a variable called MACHINE rather than the usual
ARCH though as far as I can tell (including for x86_64) the value is the
same as we would use for architecture.
When cross compiling with LLVM we don't need a CROSS_COMPILE as LLVM can
support many target architectures in a single build so this logic does not
work, CROSS_COMPILE is not set and we end up selecting tests for the host
rather than target architecture. Fix this by using the more standard ARCH
to describe the architecture, taking it from the environment if specified.
Link: https://lkml.kernel.org/r/20230614-kselftest-mm-llvm-v1-1-180523f277d3@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Tom Rix <trix@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This allows to do more centralized decisions later on, and generally
makes it very explicit which maps are privileged and which are not
(e.g., LRU_HASH and LRU_PERCPU_HASH, which are privileged HASH variants,
as opposed to unprivileged HASH and HASH_PERCPU; now this is explicit
and easy to verify).
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20230613223533.3689589-4-andrii@kernel.org
Assertions reports are split into two parts, the exact file and location
of the condition and then the stack trace printed from
btrfs_assertfail(). This means all the stack traces report the same line
and this is what's typically reported by various tools, making it harder
to distinguish the reports.
[403.2467] assertion failed: refcount_read(&block_group->refs) == 1, in fs/btrfs/block-group.c:4259
[403.2479] ------------[ cut here ]------------
[403.2484] kernel BUG at fs/btrfs/messages.c:259!
[403.2488] invalid opcode: 0000 [#1] PREEMPT SMP KASAN
[403.2493] CPU: 2 PID: 23202 Comm: umount Not tainted 6.2.0-rc4-default+ #67
[403.2499] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552-rebuilt.opensuse.org 04/01/2014
[403.2509] RIP: 0010:btrfs_assertfail+0x19/0x1b [btrfs]
...
[403.2595] Call Trace:
[403.2598] <TASK>
[403.2601] btrfs_free_block_groups.cold+0x52/0xae [btrfs]
[403.2608] close_ctree+0x6c2/0x761 [btrfs]
[403.2613] ? __wait_for_common+0x2b8/0x360
[403.2618] ? btrfs_cleanup_one_transaction.cold+0x7a/0x7a [btrfs]
[403.2626] ? mark_held_locks+0x6b/0x90
[403.2630] ? lockdep_hardirqs_on_prepare+0x13d/0x200
[403.2636] ? __call_rcu_common.constprop.0+0x1ea/0x3d0
[403.2642] ? trace_hardirqs_on+0x2d/0x110
[403.2646] ? __call_rcu_common.constprop.0+0x1ea/0x3d0
[403.2652] generic_shutdown_super+0xb0/0x1c0
[403.2657] kill_anon_super+0x1e/0x40
[403.2662] btrfs_kill_super+0x25/0x30 [btrfs]
[403.2668] deactivate_locked_super+0x4c/0xc0
By making btrfs_assertfail a macro we'll get the same line number for
the BUG output:
[63.5736] assertion failed: 0, in fs/btrfs/super.c:1572
[63.5758] ------------[ cut here ]------------
[63.5782] kernel BUG at fs/btrfs/super.c:1572!
[63.5807] invalid opcode: 0000 [#2] PREEMPT SMP KASAN
[63.5831] CPU: 0 PID: 859 Comm: mount Tainted: G D 6.3.0-rc7-default+ #2062
[63.5868] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a-rebuilt.opensuse.org 04/01/2014
[63.5905] RIP: 0010:btrfs_mount+0x24/0x30 [btrfs]
[63.5964] RSP: 0018:ffff88800e69fcd8 EFLAGS: 00010246
[63.5982] RAX: 000000000000002d RBX: ffff888008fc1400 RCX: 0000000000000000
[63.6004] RDX: 0000000000000000 RSI: ffffffffb90fd868 RDI: ffffffffbcc3ff20
[63.6026] RBP: ffffffffc081b200 R08: 0000000000000001 R09: ffff88800e69fa27
[63.6046] R10: ffffed1001cd3f44 R11: 0000000000000001 R12: ffff888005a3c370
[63.6062] R13: ffffffffc058e830 R14: 0000000000000000 R15: 00000000ffffffff
[63.6081] FS: 00007f7b3561f800(0000) GS:ffff88806c600000(0000) knlGS:0000000000000000
[63.6105] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[63.6120] CR2: 00007fff83726e10 CR3: 0000000002a9e000 CR4: 00000000000006b0
[63.6137] Call Trace:
[63.6143] <TASK>
[63.6148] legacy_get_tree+0x80/0xd0
[63.6158] vfs_get_tree+0x43/0x120
[63.6166] do_new_mount+0x1f3/0x3d0
[63.6176] ? do_add_mount+0x140/0x140
[63.6187] ? cap_capable+0xa4/0xe0
[63.6197] path_mount+0x223/0xc10
This comes at a cost of bloating the final btrfs.ko module due all the
inlining, as long as assertions are compiled in. This is a must for
debugging builds but this is often enabled on release builds too.
Release build:
text data bss dec hex filename
1251676 20317 16088 1288081 13a791 pre/btrfs.ko
1260612 29473 16088 1306173 13ee3d post/btrfs.ko
DELTA: +8936
CC: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: David Sterba <dsterba@suse.com>
Add a utility 'lsdexcr' to print the current DEXCR status. Useful for
quickly checking the status such as when debugging test failures or
verifying the new default DEXCR does what you want (for userspace at
least). Example output:
# ./lsdexcr
uDEXCR: 04000000 (NPHIE)
HDEXCR: 00000000
Effective: 04000000 (NPHIE)
SBHE (0): clear (Speculative branch hint enable)
IBRTPD (3): clear (Indirect branch recurrent target ...)
SRAPD (4): clear (Subroutine return address ...)
NPHIE * (5): set (Non-privileged hash instruction enable)
PHIE (6): clear (Privileged hash instruction enable)
DEXCR[NPHIE] enabled: hashst/hashchk working
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230616034846.311705-12-bgray@linux.ibm.com
Test the kernel DEXCR[NPHIE] interface and hashchk exception handling.
Introduces with it a DEXCR utils library for common DEXCR operations.
Volatile is used to prevent the compiler optimising away the signal
tests.
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230616034846.311705-11-bgray@linux.ibm.com
Adds _MSG assertion variants to provide more context behind why a
failure occurred. Also include unistd.h for _exit() and stdio.h for
fprintf(), and move ARRAY_SIZE macro to utils.h.
The _MSG variants and ARRAY_SIZE will be used by the following
DEXCR selftests.
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230616034846.311705-10-bgray@linux.ibm.com
Test that target gets created by register_sysctl_mount_point and that no
additional target can be created "on top" of a permanently empty sysctl
table.
Create a mount point target (mnt) in the sysctl test driver; try to
create another on top of that (mnt_error). Output an error if
"mnt_error" is present when we run the sysctl selftests.
Signed-off-by: Joel Granados <j.granados@samsung.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Tests were being skipped because the target was not present. Add a flag
that controls whether to skip a test based on the presence of the target.
Actually skip tests in the test_case function with a "return" instead of
a "continue".
Signed-off-by: Joel Granados <j.granados@samsung.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Add a test that checks that the unregistered directory is removed from
/proc/sys/debug
Signed-off-by: Joel Granados <j.granados@samsung.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
The functions get_test_{count,enabled,target} use awk to get the N'th
field in the ALL_TESTS variable. A variable with leading zeros (e.g.
0009) is misinterpreted as an entire line instead of the N'th field.
Remove the leading zeros so this does not happen. We can now use the
helper in tests 6, 7 and 8.
Signed-off-by: Joel Granados <j.granados@samsung.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
In some architectures we can't encode the PMU number in
perf_event_attr.type and thus can't just ask for the same event in
multiple CPUs (and thus PMUs), that is what we want in hybrid systems
but we can't when that encoding isn't understood by the kernel, such as
in ARM64's big.LITTLE.
If that is the case, fallback to the previous behaviour till we find a
better solution to have consistent output accross architectures with
hybrid CPU configurations.
Co-developed-with: Ian Rogers <irogers@google.com>
Cc: James Clark <james.clark@arm.com>
Cc: John Garry <john.g.garry@oracle.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Sumanth Korikkar <sumanthk@linux.ibm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/linux-perf-users/ZIzYgImv61OGK1wA@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Will be used when checking if we can encode the PMU number in
perf_event_attr.type, part of the logic to use in hybrid systems
(multiple types of CPUs, such as Intel's (Alder Lake, etc) or ARM's
big.LITTLE).
Co-developed-with: Ian Rogers <irogers@google.com>
Cc: James Clark <james.clark@arm.com>
Cc: John Garry <john.g.garry@oracle.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Sumanth Korikkar <sumanthk@linux.ibm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/linux-perf-users/ZIzYgImv61OGK1wA@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
There exists the following warning when executing 'perf test record+probe_libc_inet_pton.sh':
fgrep: warning: fgrep is obsolescent; using grep -F
This is tested on Fedora 38, the version of grep is 3.8, the latest
version of grep claims the fgrep is obsolete, use "grep -F" instead of
"fgrep" to silence the warning.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: loongson-kernel@lists.loongnix.cn
Link: https://lore.kernel.org/r/1686880567-30017-1-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Scanning only core PMUs is not sufficient on platforms like AMD since
perf mem on AMD uses IBS OP PMU, which is independent of core PMU.
Scan all PMUs instead of just core PMUs. There should be negligible
performance overhead because of scanning all PMUs, so we should be okay.
Reviewed-by: Ian Rogers <irogers@google.com>
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ali Saidi <alisaidi@amazon.com>
Cc: Ananth Narayan <ananth.narayan@amd.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sandipan Das <sandipan.das@amd.com>
Cc: Santosh Shukla <santosh.shukla@amd.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Link: https://lore.kernel.org/r/20230615051700.1833-4-ravi.bangoria@amd.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
perf mem/c2c on AMD internally uses IBS OP PMU, not the core PMU. Also,
AMD platforms does not have heterogeneous PMUs.
Reviewed-by: Ian Rogers <irogers@google.com>
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ali Saidi <alisaidi@amazon.com>
Cc: Ananth Narayan <ananth.narayan@amd.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sandipan Das <sandipan.das@amd.com>
Cc: Santosh Shukla <santosh.shukla@amd.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Link: https://lore.kernel.org/r/20230615051700.1833-3-ravi.bangoria@amd.com
[ Added the improved comment for perf_pmus__num_mem_pmus() as b4 didn't from the per-patch (not series) newer version ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Notion of 'core_pmus' and 'other_pmus' are independent of hw core and
uncore pmus. For example, AMD IBS PMUs are present in each SMT-thread
but they belongs to 'other_pmus'. Add a comment describing what these
list contains and how they are treated.
Reviewed-by: Ian Rogers <irogers@google.com>
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ali Saidi <alisaidi@amazon.com>
Cc: Ananth Narayan <ananth.narayan@amd.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sandipan Das <sandipan.das@amd.com>
Cc: Santosh Shukla <santosh.shukla@amd.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Link: https://lore.kernel.org/r/20230615051700.1833-2-ravi.bangoria@amd.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When -r option is used, perf stat runs the command multiple times and
update stats in the evsel->stats.res_stats for global aggregation. But
the value is never used and the value it prints at the end is just the
value from the last run. I think we should print the average number of
multiple runs.
Add evlist__copy_res_stats() to update the aggr counter (for display)
using the values in the evsel->stats.res_stats.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230616073211.1057936-2-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When it runs multiple times with -r option, it missed to reset the
aggregation counters and the values were added up. The aggregation
count has the values to be printed in the end. It should reset the
counters at the beginning of each run. But the current code does that
only when -I/--interval-print option is given.
Fixes: 91f85f98da ("perf stat: Display event stats using aggr counts")
Reported-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230616073211.1057936-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
In linux-next tree the many test cases fail on s390x when running the
perf test suite, sometime the perf tool dumps core.
Output before:
6.1: Test event parsing : FAILED!
10.3: Parsing of PMU event table metrics : FAILED!
10.4: Parsing of PMU event table metrics with fake PMUs: FAILED!
17: Setup struct perf_event_attr : FAILED!
24: Number of exit events of a simple workload : FAILED!
26: Object code reading : FAILED!
28: Use a dummy software event to keep tracking : FAILED!
35: Track with sched_switch : FAILED!
42.3: BPF prologue generation : FAILED!
66: Parse and process metrics : FAILED!
68: Event expansion for cgroups : FAILED!
69.2: Perf time to TSC : FAILED!
74: build id cache operations : FAILED!
86: Zstd perf.data compression/decompression : FAILED!
87: perf record tests : FAILED!
106: Test java symbol : FAILED!
The reason for all these failure is a missing PMU. On s390x the PMU is
named cpum_cf which is not detected as core PMU. A similar patch was
added before, see commit 9bacbced0e ("perf list: Add s390 support
for detailed PMU event description") which got lost during the recent
reworks. Add it again.
Output after:
10.2: PMU event map aliases : FAILED!
42.3: BPF prologue generation : FAILED!
Most test cases now work and there is not core dump anymore.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Sumanth Korikkar <sumanthk@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Link: https://lore.kernel.org/r/20230616081437.1932003-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It is currently possible to use --symfs along with a vmlinux which lies
outside of the symfs by passing an absolute path to --vmlinux, thanks to
the check in dso__load_vmlinux() which handles this explicitly.
However, the annotate code lacks this check and thus 'perf annotate'
does not work ("Internal error: Invalid -1 error code") for kernel
functions with this combination. Add the missing handling.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: kernel@axis.com
Link: https://lore.kernel.org/r/20221125114210.2353820-1-vincent.whitchurch@axis.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add a new test case to verify the standard 'perf stat' output with
different options.
Reviewed-by: Ian Rogers <irogers@google.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ahmad Yasin <ahmad.yasin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20230616031420.3751973-5-kan.liang@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
These functions can be shared with the stat std output test.
There is no functional change.
Reviewed-by: Ian Rogers <irogers@google.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ahmad Yasin <ahmad.yasin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20230616031420.3751973-4-kan.liang@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
In the default mode, the current output of the metricgroup include both
events and metrics, which is not necessary and just makes the output
hard to read. Since different ARCHs (even different generations in the
same ARCH) may use different events. The output also vary on different
platforms.
For a metricgroup, only outputting the value of each metric is good
enough.
Add a new field default_metricgroup in evsel to indicate an event of the
default metricgroup. For those events, printout() should print the
metricgroup name rather than each event.
Add perf_stat__skip_metric_event() to skip the evsel in the Default
metricgroup, if it's not running or not the metric event.
Add print_metricgroup_header_t to pass the functions which print the
display name of each metricgroup in the Default metricgroup. Support all
three output methods.
Factor out perf_stat__print_shadow_stats_metricgroup() to print out each
metrics.
On SPR:
Before:
./perf_old stat sleep 1
Performance counter stats for 'sleep 1':
0.54 msec task-clock:u # 0.001 CPUs utilized
0 context-switches:u # 0.000 /sec
0 cpu-migrations:u # 0.000 /sec
68 page-faults:u # 125.445 K/sec
540,970 cycles:u # 0.998 GHz
556,325 instructions:u # 1.03 insn per cycle
123,602 branches:u # 228.018 M/sec
6,889 branch-misses:u # 5.57% of all branches
3,245,820 TOPDOWN.SLOTS:u # 18.4 % tma_backend_bound
# 17.2 % tma_retiring
# 23.1 % tma_bad_speculation
# 41.4 % tma_frontend_bound
564,859 topdown-retiring:u
1,370,999 topdown-fe-bound:u
603,271 topdown-be-bound:u
744,874 topdown-bad-spec:u
12,661 INT_MISC.UOP_DROPPING:u # 23.357 M/sec
1.001798215 seconds time elapsed
0.000193000 seconds user
0.001700000 seconds sys
After:
$ ./perf stat sleep 1
Performance counter stats for 'sleep 1':
0.51 msec task-clock:u # 0.001 CPUs utilized
0 context-switches:u # 0.000 /sec
0 cpu-migrations:u # 0.000 /sec
68 page-faults:u # 132.683 K/sec
545,228 cycles:u # 1.064 GHz
555,509 instructions:u # 1.02 insn per cycle
123,574 branches:u # 241.120 M/sec
6,957 branch-misses:u # 5.63% of all branches
TopdownL1 # 17.5 % tma_backend_bound
# 22.6 % tma_bad_speculation
# 42.7 % tma_frontend_bound
# 17.1 % tma_retiring
TopdownL2 # 21.8 % tma_branch_mispredicts
# 11.5 % tma_core_bound
# 13.4 % tma_fetch_bandwidth
# 29.3 % tma_fetch_latency
# 2.7 % tma_heavy_operations
# 14.5 % tma_light_operations
# 0.8 % tma_machine_clears
# 6.1 % tma_memory_bound
1.001712086 seconds time elapsed
0.000151000 seconds user
0.001618000 seconds sys
Reviewed-by: Ian Rogers <irogers@google.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ahmad Yasin <ahmad.yasin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20230616031420.3751973-3-kan.liang@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The new default mode will print the metrics as a metric group. The
metrics from the same metric group must be adjacent to each other in the
metric list. But the metric_list_cmp() sorts metrics by the number of
events.
Add a new sort for the Default metricgroup, which sorts by
default_metricgroup_name and metric_name.
Add is_default in the struct metric_event to indicate that it's from
the Default metricgroup.
Store the displayed metricgroup name of the Default metricgroup into
the metric expr for output.
Reviewed-by: Ian Rogers <irogers@google.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ahmad Yasin <ahmad.yasin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20230616031420.3751973-2-kan.liang@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
SYSFS_PATH can be used locally and globally, especially that has
the same content.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add a selftest for CMMA migration on s390.
The tests cover:
- interaction of dirty tracking and migration mode, see my recent patch
"KVM: s390: disable migration mode when dirty tracking is disabled" [1],
- several invalid calls of KVM_S390_GET_CMMA_BITS, for example: invalid
flags, CMMA support off, with/without peeking
- ensure KVM_S390_GET_CMMA_BITS initally reports all pages as dirty,
- ensure KVM_S390_GET_CMMA_BITS properly skips over holes in memslots, but
also non-dirty pages
Note that without the patch at [1] and the small fix in this series, the
selftests will fail.
[1] https://lore.kernel.org/all/20230127140532.230651-2-nrb@linux.ibm.com/
Signed-off-by: Nico Boehr <nrb@linux.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Message-Id: <20230324145424.293889-3-nrb@linux.ibm.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
[frankja@linux.ibm.com: squashed
20230606150510.671301-1-nrb@linux.ibm.com / "KVM: s390: selftests:
CMMA: don't run if CMMA not supported"]
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
There are some MD5 tests which fail when the kernel is in FIPS mode,
since MD5 is not FIPS compliant. Add a check and only run those tests
if FIPS mode is not enabled.
Fixes: f0bee1ebb5 ("fcnal-test: Add TCP MD5 tests")
Fixes: 5cad8bce26 ("fcnal-test: Add TCP MD5 tests for VRF")
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Magali Lemes <magali.lemes@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The vrf-xfrm-tests tests use the hmac(md5) and cbc(des3_ede)
algorithms for performing authentication and encryption, respectively.
This causes the tests to fail when fips=1 is set, since these algorithms
are not allowed in FIPS mode. Therefore, switch from hmac(md5) and
cbc(des3_ede) to hmac(sha1) and cbc(aes), which are FIPS compliant.
Fixes: 3f251d7411 ("selftests: Add tests for vrf and xfrms")
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Magali Lemes <magali.lemes@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
TLS selftests use the ChaCha20-Poly1305 and SM4 algorithms, which are not
FIPS compliant. When fips=1, this set of tests fails. Add a check and only
run these tests if not in FIPS mode.
Fixes: 4f336e88a8 ("selftests/tls: add CHACHA20-POLY1305 to tls selftests")
Fixes: e506342a03 ("selftests/tls: add SM4 GCM/CCM to tls selftests")
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Magali Lemes <magali.lemes@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before executing each test from a fixture, FIXTURE_SETUP is run once.
When SKIP is used in FIXTURE_SETUP, the setup function returns early
but the test still proceeds to run, unless another SKIP macro is used
within the test definition, leading to some code repetition. Therefore,
allow tests to be skipped directly from the setup function.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Magali Lemes <magali.lemes@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Selftests excluded - we have 58 patches and diff of +442/-199,
which isn't really small but perhaps with the exception of
the WiFi locking change it's old(ish) bugs.
We have no known problems with v6.4.
The selftest changes are rather large as MPTCP folks try to apply
Greg's guidance that selftest from torvalds/linux should be able
to run against stable kernels.
Last thing I should call out is the DCCP/UDP-lite deprecation notices,
we are fairly sure those are dead, but if we're wrong reverting them
back in won't be fun.
Current release - regressions:
- wifi:
- cfg80211: fix double lock bug in reg_wdev_chan_valid()
- iwlwifi: mvm: spin_lock_bh() to fix lockdep regression
Current release - new code bugs:
- handshake: remove fput() that causes use-after-free
Previous releases - regressions:
- sched: cls_u32: fix reference counter leak leading to overflow
- sched: cls_api: fix lockup on flushing explicitly created chain
Previous releases - always broken:
- nf_tables: integrate pipapo into commit protocol
- nf_tables: incorrect error path handling with NFT_MSG_NEWRULE,
fix dangling pointer on failure
- ping6: fix send to link-local addresses with VRF
- sched: act_pedit: parse L3 header for L4 offset, the skb may
not have the offset saved
- sched: act_ct: fix promotion of offloaded unreplied tuple
- sched: refuse to destroy an ingress and clsact Qdiscs if there
are lockless change operations in flight
- wifi: mac80211: fix handful of bugs in multi-link operation
- ipvlan: fix bound dev checking for IPv6 l3s mode
- eth: enetc: correct the indexes of highest and 2nd highest TCs
- eth: ice: fix XDP memory leak when NIC is brought up and down
Misc:
- add deprecation notices for UDP-lite and DCCP
- selftests: mptcp: skip tests not supported by old kernels
- sctp: handle invalid error codes without calling BUG()
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=oNA0
-----END PGP SIGNATURE-----
Merge tag 'net-6.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from wireless, and netfilter.
Selftests excluded - we have 58 patches and diff of +442/-199, which
isn't really small but perhaps with the exception of the WiFi locking
change it's old(ish) bugs.
We have no known problems with v6.4.
The selftest changes are rather large as MPTCP folks try to apply
Greg's guidance that selftest from torvalds/linux should be able to
run against stable kernels.
Last thing I should call out is the DCCP/UDP-lite deprecation notices.
We are fairly sure those are dead, but if we're wrong reverting them
back in won't be fun.
Current release - regressions:
- wifi:
- cfg80211: fix double lock bug in reg_wdev_chan_valid()
- iwlwifi: mvm: spin_lock_bh() to fix lockdep regression
Current release - new code bugs:
- handshake: remove fput() that causes use-after-free
Previous releases - regressions:
- sched: cls_u32: fix reference counter leak leading to overflow
- sched: cls_api: fix lockup on flushing explicitly created chain
Previous releases - always broken:
- nf_tables: integrate pipapo into commit protocol
- nf_tables: incorrect error path handling with NFT_MSG_NEWRULE, fix
dangling pointer on failure
- ping6: fix send to link-local addresses with VRF
- sched: act_pedit: parse L3 header for L4 offset, the skb may not
have the offset saved
- sched: act_ct: fix promotion of offloaded unreplied tuple
- sched: refuse to destroy an ingress and clsact Qdiscs if there are
lockless change operations in flight
- wifi: mac80211: fix handful of bugs in multi-link operation
- ipvlan: fix bound dev checking for IPv6 l3s mode
- eth: enetc: correct the indexes of highest and 2nd highest TCs
- eth: ice: fix XDP memory leak when NIC is brought up and down
Misc:
- add deprecation notices for UDP-lite and DCCP
- selftests: mptcp: skip tests not supported by old kernels
- sctp: handle invalid error codes without calling BUG()"
* tag 'net-6.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (91 commits)
dccp: Print deprecation notice.
udplite: Print deprecation notice.
octeon_ep: Add missing check for ioremap
selftests/ptp: Fix timestamp printf format for PTP_SYS_OFFSET
net: ethernet: stmicro: stmmac: fix possible memory leak in __stmmac_open
net: tipc: resize nlattr array to correct size
sfc: fix XDP queues mode with legacy IRQ
net: macsec: fix double free of percpu stats
net: lapbether: only support ethernet devices
MAINTAINERS: add reviewers for SMC Sockets
s390/ism: Fix trying to free already-freed IRQ by repeated ism_dev_exit()
net: dsa: felix: fix taprio guard band overflow at 10Mbps with jumbo frames
net/sched: cls_api: Fix lockup on flushing explicitly created chain
ice: Fix ice module unload
net/handshake: remove fput() that causes use-after-free
selftests: forwarding: hw_stats_l3: Set addrgenmode in a separate step
net/sched: qdisc_destroy() old ingress and clsact Qdiscs before grafting
net/sched: Refactor qdisc_graft() for ingress and clsact Qdiscs
net/sched: act_ct: Fix promotion of offloaded unreplied tuple
wifi: iwlwifi: mvm: spin_lock_bh() to fix lockdep regression
...
There may be multiplexing triggered, e.g., e-core of ADL.
Reviewed-by: Ian Rogers <irogers@google.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ahmad Yasin <ahmad.yasin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20230615135315.3662428-7-kan.liang@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Introduce a new metricgroup, Default, to tag all the metric groups which
will be collected in the default mode.
Add a new field, DefaultMetricgroupName, in the JSON file to indicate
the real metric group name. It will be printed in the default output
to replace the event names.
There is nothing changed for the output format.
On SPR, both TopdownL1 and TopdownL2 are displayed in the default
output.
On ARM, Intel ICL and later platforms (before SPR), only TopdownL1 is
displayed in the default output.
Suggested-by: Stephane Eranian <eranian@google.com>
Reviewed-by: Ian Rogers <irogers@google.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ahmad Yasin <ahmad.yasin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230615135315.3662428-4-kan.liang@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
