Some SD-cards from Sandisk that are SDA-6.0 compliant reports they supports
discard, while they actually don't. This might cause mk2fs to fail while
trying to format the card and revert it to a read-only mode.
To fix this problem, let's add a card quirk (MMC_QUIRK_BROKEN_SD_DISCARD)
to indicate that we shall fall-back to use the legacy erase command
instead.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220928095744.16455-1-avri.altman@wdc.com
[Ulf: Updated the commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In mmc_fixup_of_compatible_match(), we should call of_node_put()
when breaking out of for_each_child_of_node() which will increase
and decrease the refcount during one iteration.
Fixes: b360b11026 ("mmc: core: allow to match the device tree to apply quirks")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220719091051.1210806-1-windhl@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Until now, the SDIO quirks are applied directly from the driver.
However, it is better to apply the quirks before driver probing. So,
this patch relocate the quirks in the MMC framework.
Note that the WF200 has no valid SDIO VID/PID. Therefore, we match DT
rather than on the SDIO VID/PID.
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20220216093112.92469-3-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TiWi WL1251 WiFi chip needs special setup of the sdio
interface before it can be probed.
So far, this is done in omap_hsmmc_init_card() in omap_hsmmc.c
which makes it useable only if connected to omap devices
which use the omap_hsmmc. The OpenPandora is the most promient
example.
There are plans to switch to a newer sdhci-omap driver and
retire omap_hsmmc. Hence this quirk must be reworked or moved
somewhere else. Ideally to some location that is not dependent
on the specific SoC mmc host driver.
This is achieved by the new mmc_fixup_device() option introduced
by ("mmc: allow to match the device tree to apply quirks") to match
through device tree compatible string.
This quirk will be called early right after where host->ops->init_card()
and thus omap_hsmmc_init_card() was previously called.
Note that we do not need to transplant
card->ocr = 0x80;
because we rely on ("mmc: core: Fixup storing of OCR for MMC_QUIRK_NONSTD_SDIO").
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/774565df7f02124c003aaf8b879706352548f832.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This (initially empty) table allows to match quirks early based
on .compatible of the child node of some mmc/sdio interface.
This allows to add quirks based on device tree instead of having
card specific code in the host ops.
A new macro SDIO_FIXUP_COMPATIBLE makes the definition readable.
And we call mmc_fixup_device(sdio_card_init_methods) just after
where host->ops->init_card() can be optionally called.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/b13fd8b3eebc3c23b6816b254a518c224cbdcfd4.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC subsystem provides a way to apply quirks when a device match some
properties (VID, PID, etc...) Unfortunately, some SDIO devices do not
comply with the SDIO specification and does not provide reliable VID/PID
(eg. Silabs WF200).
So, the drivers for these devices rely on device tree to identify the
device.
This patch allows the MMC to also rely on the device tree to apply a
quirk.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/9e68e3d23e62a78527aabc1281f89e15200c7d09.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, mmc_fixup_device() is a bit difficult to read because of
particularly long condition.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/6515c1e8b3aa69ad273726f6e877d85c20f286ad.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Not all source files which include quirks.h make use of the all of
the available fixup information. When this happens the compiler
complains that some constant variables are defined by never used.
We can fix this by telling the compiler that this intentional by
simply marking them as __maybe_unused.
Fixes the following W=1 kernel build warnings:
In file included from drivers/mmc/core/sdio.c:22:
drivers/mmc/core/quirks.h:105:31: warning: ‘mmc_ext_csd_fixups’ defined but not used [-Wunused-const-variable=]
105 | static const struct mmc_fixup mmc_ext_csd_fixups[] = {
| ^~~~~~~~~~~~~~~~~~
drivers/mmc/core/quirks.h:17:31: warning: ‘mmc_blk_fixups’ defined but not used [-Wunused-const-variable=]
17 | static const struct mmc_fixup mmc_blk_fixups[] = {
| ^~~~~~~~~~~~~~
In file included from drivers/mmc/core/mmc.c:25:
drivers/mmc/core/quirks.h:123:31: warning: ‘sdio_fixup_methods’ defined but not used [-Wunused-const-variable=]
123 | static const struct mmc_fixup sdio_fixup_methods[] = {
| ^~~~~~~~~~~~~~~~~~
drivers/mmc/core/quirks.h:17:31: warning: ‘mmc_blk_fixups’ defined but not used [-Wunused-const-variable=]
17 | static const struct mmc_fixup mmc_blk_fixups[] = {
| ^~~~~~~~~~~~~~
Cc: Andrei Warkentin <andreiw@motorola.com>
Cc: Martin Mares <mj@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-2-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Marvell SDIO device ID 0x9134 is used in SDIO Common CIS (Card Information
Structure) and not in SDIO wlan function (with ID 1). SDIO Common CIS is
accessed by function ID 0.
So change this misleading macro name to SDIO_DEVICE_ID_MARVELL_8887_F0 as
it does not refer to wlan function. It refers to function 0.
Wlan module on this SDIO card is available at function ID 1 and is
identified by different SDIO device ID 0x9135. Kernel quirks for SDIO
devices are matched against device ID from SDIO Common CIS. Therefore
device ID used in quirk is correct, just has misleading name.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-2-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
wl1251 and wl1271 have different vendor id and device id.
So we need to handle both with sdio quirks.
Fixes: 884f386078 ("mmc: core: move some sdio IDs out of quirks file")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch uses limit clock rate quirk to reduce clock rate
for "SDR104" mode on IMX side for Marvell 8887
WiFi + Bluetooth chip side, as Marvell does not recommend
to use SDIO at the speed of higher than 150MHz.
Signed-off-by: Diwakar Sharma <diwakar.sharma@in.bosch.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Certain Micron eMMC v4.5 cards might get broken when HPI feature is used
and hence this patch disables the HPI feature for such buggy cards.
In U-Boot, these cards are reported as
Manufacturer: Micron (ID: 0xFE)
OEM: 0x4E
Name: MMC32G
Revision: 19 (0x13)
Serial: 959241022 Manufact. date: 8/2015 (0x82) CRC: 0x00
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.5
High Capacity: Yes
Capacity: 29.1 GiB
Boot Partition Size: 16 MiB
Bus Width: 8-bit
According to JEDEC JEP106 manufacturer 0xFE is Numonyx, which was bought by
Micron.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Cc: <stable@vger.kernel.org> # 4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That makes all the quirks table look more consistent.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's not appreciated to place quirks everywhere, let's
put them together just like what we do for USB, PCI etc.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rename mmc_fixup_methods to sdio_fixup_methods to better
reflect that it's for sdio devices. So we could also pass
on it from sdio card's probe sequence just like what we do
for eMMC and block there.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Consolidate all the sdio devices' IDs into sdio_ids.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rename quirks.c to quirks.h, and include it for
individual C files which need it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Avri Altman