The Multi Innotechnology is a 10.1" 1280x800 panel.
The datasheet did not specify specific values for sync, back, front porch.
The values are a best guess based on values for similar panels.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Co-developed-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210805111944.13533-2-o.rempel@pengutronix.de
The Gopher 2b LCD panel is used in Gopher 2b handhelds.
It's simple panel with NewVision NV3047 driver, but SPI lines are not
connected. It has no specific name, since it's unique to that handheld.
lot name at AliExpress: 4.3 inch 40PIN TFT LCD Screen COG NV3047 Drive
IC 480(RGB)*272 No Touch 24Bit RGB Interface
Signed-off-by: Artjom Vejsel <akawolf0@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20210804002353.76385-4-akawolf0@gmail.com
This reverts commit 18a1488bf1.
Those delays were added to support the Samsung ATNA33XC20
panel. However, we've moving that to its own panel driver and out of
panel-simple. That means we don't need the ability to specify this
delay.
NOTE: it's unlikely we want to keep this delay "just in case" some
other panel needs it. The enable-gpio and the power supply are really
supposed to be different ways to specify the same thing: the main
enable of the panel. Supporting a delay between them doesn't really
make sense.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730084534.v2.5.Ie44e3e5b7a926392541d575ca84c56931596513f@changeid
This reverts commit 4bfe6c8f7c.
This panel's power sequencing really can't be handled properly by
panel-simple because of the special sequencing needed for the EL_ON3
GPIO. The only way it was sorta working in the past was by trying to
jam that signal into the "enable-gpio", but that really wasn't a good
fit. We'll add a custom panel driver for this panel to do it right.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730084534.v2.4.Id9f076ec5f35633f8ce931051af268a04c45c075@changeid
Many of the DSI flags have names opposite to their actual effects,
e.g. MIPI_DSI_MODE_EOT_PACKET means that EoT packets will actually
be disabled. Fix this by including _NO_ in the flag names, e.g.
MIPI_DSI_MODE_NO_EOT_PACKET.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@samsung.com>
Reviewed-by: Xin Ji <xji@analogixsemi.com> # anx7625.c
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> # msm/dsi
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727094435.v3.1.I629b2366a6591410359c7fcf6d385b474b705ca2@changeid
When I tried booting up a device that needed the DP AUX backlight, I
found an error in the logs:
panel-simple-dp-aux: probe of aux-ti_sn65dsi86.aux.0 failed with error -110
The aux transfers were failing because the panel wasn't powered. Just
like when reading the EDID we need to power the panel when trying to
talk to it. Add the needed pm_runtime calls.
After I do this I can successfully probe the panel and adjust the
backlight on my board.
Fixes: bfd451403d ("drm/panel-simple: Support DP AUX backlight")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210714093334.1.Idb41f87e5abae4aee0705db7458b0097fc50e7ab@changeid
This patch adds support for the EDT ETM0350G0DH6 3.5" (320x240) lcd
panel to DRM simple panel driver.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Yunus Bas <y.bas@phytec.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210709200349.2665205-2-y.bas@phytec.de
This patch adds support for the EDT ETMV570G2DHU 5.7" (640x480) lcd panel
to DRM simple panel driver.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Yunus Bas <y.bas@phytec.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210709200349.2665205-1-y.bas@phytec.de
Do not give a warning for the eDP panels if the "bus_format" is
not specified, since most eDP panels can support more than one
bus formats and this can be auto-detected.
Also, update the check to include bpc=10 for the eDP panel.
Signed-off-by: Rajeev Nandan <rajeevny@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1624726268-14869-5-git-send-email-rajeevny@codeaurora.org
If there is no backlight specified in the device tree and the panel
has access to the DP AUX channel then create a DP AUX backlight if
supported by the panel.
Signed-off-by: Rajeev Nandan <rajeevny@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1624726268-14869-3-git-send-email-rajeevny@codeaurora.org
The connector_type for following two EDT displays is missing:
- EDT ETM0430G0DH6
- EDT ETM0700G0BDH6
Both are parallel displays thus add the corresponding connector_type.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210621150930.86617-2-s.riedmueller@phytec.de
The AUO G104SN02 V2 is an LVDS display which supports 6 and 8 bpc PSWG.
Add the corresponding connector type and 8 bpc as default bus_format.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210621150930.86617-1-s.riedmueller@phytec.de
If panel-simple is instantiated as a DP AUX bus endpoint then we have
access to the DP AUX bus. Let's stash it in the panel-simple
structure, leaving it NULL for the cases where the panel is
instantiated in other ways.
If we happen to have access to the DP AUX bus and we weren't provided
the ddc-i2c-bus in some other manner, let's use the DP AUX bus for it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210611101711.v10.6.I18e60221f6d048d14d6c50a770b15f356fa75092@changeid
The panel-simple driver can already have devices instantiated as
platform devices or MIPI DSI devices. Let's add a 3rd way to
instantiate it: as DP AUX endpoint devices.
At the moment there is no benefit to instantiating it in this way,
but:
- In the next patch we'll give it access to the DDC channel via the DP
AUX bus.
- Possibly in the future we may use this channel to configure the
backlight.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210611101711.v10.5.Iada41f76a7342354bae929d0bb3ceba40f27f0ea@changeid
The PM Runtime docs specifically call out the need to call
pm_runtime_dont_use_autosuspend() in the remove() callback if
pm_runtime_use_autosuspend() was called in probe():
> Drivers in ->remove() callback should undo the runtime PM changes done
> in ->probe(). Usually this means calling pm_runtime_disable(),
> pm_runtime_dont_use_autosuspend() etc.
We should do this. This fixes a warning splat that I saw when I was
testing out the panel-simple's remove().
Fixes: 3235b0f20a ("drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210517130450.v7.1.I9e947183e95c9bd067c9c1d51208ac6a96385139@changeid
It doesn't make sense to go out to the bus and read the EDID over and
over again. Let's cache it and throw away the cache when we turn power
off from the panel. Autosuspend means that even if there are several
calls to read the EDID before we officially turn the power on then we
should get good use out of this cache.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.18.If050957eaa85cf45b10bcf61e6f7fa61c9750ebf@changeid
I don't believe that it ever makes sense to read the EDID when a panel
is not powered and the powering on of the panel is the job of
prepare(). Let's make sure that this happens before we try to read the
EDID. We use the pm_runtime functions directly rather than directly
calling the normal prepare() function because the pm_runtime functions
are definitely refcounted whereas it's less clear if the prepare() one
is.
NOTE: I'm not 100% sure how EDID reading was working for folks in the
past, but I can only assume that it was failing on the initial attempt
and then working only later. This patch, presumably, will fix that. If
some panel out there really can read the EDID without powering up and
it's a big advantage to preserve the old behavior we can add a
per-panel flag. It appears that providing the DDC bus to the panel in
the past was somewhat uncommon in any case.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.17.Ibd31b8f7c73255d68c5c9f5b611b4bfaa036f727@changeid
As of commit 5186421cbf ("drm: Introduce epoch counter to
drm_connector") the drm_get_edid() function calls
drm_connector_update_edid_property() for us. There's no reason for us
to call it again.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.16.Icb581b0273d95cc33ca38676c61ae6d7d2e75357@changeid
When I added support for the hpd-gpio to simple-panel in commit
48834e6084 ("drm/panel-simple: Support hpd-gpios for delaying
prepare()"), I added a special case to handle a circular dependency I
was running into on the ti-sn65dsi86 bridge chip. On my board the
hpd-gpio is actually provided by the bridge chip. That was causing
some circular dependency problems that I had to work around by getting
the hpd-gpio late.
I've now reorganized the ti-sn65dsi86 bridge chip driver to be a
collection of sub-drivers. Now the GPIO part can probe separately and
that breaks the chain. Let's get rid of the old code to clean things
up.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.10.I40eeedc23459d1e3fc96fa6cdad775d88c6e706c@changeid
In commit 3235b0f20a ("drm/panel: panel-simple: Use runtime pm to
avoid excessive unprepare / prepare") we started using pm_runtime, but
my patch neglected to add the proper pm_runtime_disable(). Doh! Add
them now.
Fixes: 3235b0f20a ("drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare")
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.1.I9e6af2529d6c61e5daf86a15a1211121c5223b9a@changeid
Unpreparing and re-preparing a panel can be a really heavy
operation. Panels datasheets often specify something on the order of
500ms as the delay you should insert after turning off the panel
before turning it on again. In addition, turning on a panel can have
delays on the order of 100ms - 200ms before the panel will assert HPD
(AKA "panel ready"). The above means that we should avoid turning a
panel off if we're going to turn it on again shortly.
The above becomes a problem when we want to read the EDID of a
panel. The way that ordering works is that userspace wants to read the
EDID of the panel _before_ fully enabling it so that it can set the
initial mode correctly. However, we can't read the EDID until we power
it up. This leads to code that does this dance (like
ps8640_bridge_get_edid()):
1. When userspace requests EDID / the panel modes (through an ioctl),
we power on the panel just enough to read the EDID and then power
it off.
2. Userspace then turns the panel on.
There's likely not much time between step #1 and #2 and so we want to
avoid powering the panel off and on again between those two steps.
Let's use Runtime PM to help us. We'll move the existing prepare() and
unprepare() to be runtime resume() and runtime suspend(). Now when we
want to prepare() or unprepare() we just increment or decrement the
refcount. We'll default to a 1 second autosuspend delay which seems
sane given the typical delays we see for panels.
A few notes:
- It seems the existing unprepare() and prepare() are defined to be
no-ops if called extra times. We'll preserve that behavior but may
try to remove it in a future patch.
- This is a slight change in the ABI of simple panel. If something was
absolutely relying on the unprepare() to happen instantly that
simply won't be the case anymore. I'm not aware of anyone relying on
that behavior, but if there is someone then we'll need to figure out
how to enable (or disable) this new delayed behavior selectively.
- In order for this to work we now have a hard dependency on
"PM". From memory this is a legit thing to assume these days and we
don't have to find some fallback to keep working if someone wants to
build their system without "PM".
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210416153909.v4.7.I9e8bd33b49c496745bfac58ea9ab418bd3b6f5ce@changeid
Panel power sequence says timing T8 (time from link idle to turn on
the backlight) should be at least 50 ms. This is what the .enable
delay in simple-panel is for, so set it. NOTE: this overlaps with the
80 ms .prepare_to_enable delay on purpose. The data sheet says that
at least 80 ms needs to pass between HPD going high and turning on the
backlight and that at least 50 ms needs to pass between the link idle
and the backlight going on. Thus it works like this on the system in
front of me:
* In bridge chip pre_enable call drm_panel_prepare()
* drm_panel_prepare() -> panel_simple_prepare()
* Wait for HPD GPIO to go high.
* Start counting for 80 ms (store in prepared_time)
* In bridge chip enable, train link then call drm_panel_enable()
* drm_panel_enable() -> panel_simple_enable()
* panel_simple_enable() does hardcoded 50 ms delay then enforces 80 ms
from HPD going high (in case the bridge took less than 30 ms to
enable / link train).
* drm_panel_enable() -> backlight_enable().
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210222081716.1.I1a45aece5d2ac6a2e73bbec50da2086e43e0862b@changeid
This panel is quite similar to the similarly named N116BGE panel (the
nominal timings are, in fact identical). However, let's add a new
entry because the full range of clocks listed for N116BGE aren't
supported for N116BCA-EA1, at least according to the datasheet.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210115144345.v2.5.I3c01f3aab8335cb509da7009d8938c1a27a266dc@changeid
On an Innolux N116BCA panel that I have in front of me, sometimes HPD
simply doesn't assert no matter how long you wait for it. As per the
very wise advice of The IT Crowd ("Have you tried turning it off and
on again?") it appears that power cycling is enough to kick this panel
back into a sane state.
>From tests on this panel, it appears that leaving it powered off for a
while stimulates the problem. Adding a 6 second sleep at the start of
panel_simple_prepare_once() makes it happen fairly reliably and, with
this delay, I saw up to 3 retries needed sometimes. Without the 6
second sleep, however, the panel came up much more reliably the first
time or after only 1 retry.
While it's unknown what the problems are with this panel (and probably
the hardware should be debugged), adding a few retries to the power on
routine doesn't seem insane. Even if this panel's problems are
attributed to the fact that it's pre-production and/or can be fixed,
retries clearly can help in some cases and really don't hurt.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210115144345.v2.3.I6916959daa7c5c915e889442268d23338de17923@changeid
If a panel has an hpd_absent_delay specified then we know exactly how
long the maximum time is before HPD must be asserted. That means we
can use it as a timeout for polling the HPD pin instead of using an
arbitrary timeout. This is especially useful for dealing with panels
that periodically fail to power on and need to be retried. We can
detect the problem sooner.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210115144345.v2.2.I183b1817610d7a82fdd3bc852e96d2985df9623f@changeid
If the HPD signal never asserts in panel_simple_prepare() and we
return an error, we should unset the enable GPIO and disable the
regulator to make it consistent for the caller.
At the moment I have some hardware where HPD sometimes doesn't assert.
Obviously that needs to be debugged, but this patch makes it so that
if I add a retry that I can make things work.
Fixes: 48834e6084 ("drm/panel-simple: Support hpd-gpios for delaying prepare()")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210115144345.v2.1.I33fcbd64ab409cfe4f9491bf449f51925a4d3281@changeid
In commit 131f909ad5 ("drm: panel: simple: Fixup the struct
panel_desc kernel doc") I transitioned the more deeply nested
kerneldoc comments into the inline style. Apparently it is desirable
to continue the job and move _everything_ in this struct to inline.
Let's do it.
While doing this, we also add a short summary for the whole struct to
fix a warning when we run with extra warnings, AKA:
scripts/kernel-doc -v -rst drivers/gpu/drm/panel/panel-simple.c
The warning was:
drivers/gpu/drm/panel/panel-simple.c:42: warning: missing initial short description on line:
* struct panel_desc
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201201125822.1.I3c4191336014bd57364309439e56f600c94bb12b@changeid
Add support for the BOE NV110WTM-N61 panel. The EDID lists two modes
(one for 60 Hz refresh rate and one for 40 Hz), so we'll list both of
them here.
Note that the panel datasheet requires 80 ms between HPD asserting and
the backlight power being turned on. We'll use the new timing
constraints structure to do this cleanly. This assumes that the
backlight will be enabled _after_ the panel enable finishes. This is
how it works today and seems a sane assumption.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201109170018.v4.4.I71b2118dfc00fd7b43b02d28e7b890081c2acfa2@changeid
On the panel I'm looking at, there's an 80 ms minimum time between HPD
being asserted by the panel and setting the backlight enable GPIO.
While we could just add an 80 ms "enable" delay, this is not ideal.
Link training is allowed to happen in parallel with this delay so the
fixed 80 ms delay over-delays.
We'll support this by logging the time at the end of prepare and then
delaying in enable if enough time hasn't passed.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201109170018.v4.3.Ib9ce3c6482f464bf594161581521ced46bbd54ed@changeid
It is believed that all of the current users of the "unprepare" delay
don't actually need to wait the amount of time specified directly in
the unprepare phase. The purpose of the delay that's specified is to
allow the panel to fully power off so that we don't try to power it
back on before it's managed to full power down.
Let's use this observation to avoid the fixed delay that we currently
have. Instead of delaying, we'll note the current time when the
unprepare happens. If someone then tries to prepare the panel later
and not enough time has passed, we'll do the delay before starting the
prepare phase.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201109170018.v4.2.I06a95d83e7fa1bd919c8edd63dacacb5436e495a@changeid
When I run:
scripts/kernel-doc -rst drivers/gpu/drm/panel/panel-simple.c
I see that several of the kernel-doc entries aren't showing up because
they don't specify the full path down the hierarchy. Let's fix that
and also move to inline kernel docs.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201109170018.v4.1.Icaa86f0a4ca45a9a7184da4bc63386b29792d613@changeid
Reading the EDID of this panel shows that these flags should be set. Set
them so that we match what is in the EDID.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: b0c664cc80 ("panel: simple: Add BOE NV133FHM-N61")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201106182333.3080124-1-swboyd@chromium.org
Add the missing platform_driver_unregister() before return
from panel_simple_init in the error handling case when failed
to register panel_simple_dsi_driver with CONFIG_DRM_MIPI_DSI
enabled.
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201031011856.137307-1-miaoqinglang@huawei.com
Struct headers should start with 'struct <name>'
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/panel/panel-simple.c:42: warning: Cannot understand * @modes: Pointer to array of fixed modes appropriate for this panel. If
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201105144517.1826692-12-lee.jones@linaro.org
The OrtusTech COM43H4M85ULC panel is a 18-bit RGB panel. Commit
f098f168e9 ("drm: panel: Fix bus format for OrtusTech COM43H4M85ULC
panel") has fixed the bus formats, but forgot to address the bpc value.
Set it to 6.
Fixes: f098f168e9 ("drm: panel: Fix bus format for OrtusTech COM43H4M85ULC panel")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200824003254.21904-1-laurent.pinchart@ideasonboard.com
The panel orientation needs to parsed from a device-tree and assigned to
the panel's connector in order to make orientation property available to
userspace. That's what this patch does for the panel-simple driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200813215609.28643-5-digetx@gmail.com
Sam Ravnborg