Commit Graph

54 Commits

Author SHA1 Message Date
Josh Durgin c666601a93 rbd: move snap_rwsem to the device, rename to header_rwsem
A new temporary header is allocated each time the header changes, but
only the changed properties are copied over. We don't need a new
semaphore for each header update.

This addresses http://tracker.newdream.net/issues/2174

Signed-off-by: Josh Durgin <josh.durgin@dreamhost.com>
Reviewed-by: Alex Elder <elder@dreamhost.com>
2012-03-22 10:47:52 -05:00
Alex Elder 32eec68d2f rbd: don't drop the rbd_id too early
Currently an rbd device's id is released when it is removed, but it
is done before the code is run to clean up sysfs-related files (such
as /sys/bus/rbd/devices/1).

It's possible that an rbd is still in use after the rbd_remove()
call has been made.  It's essentially the same as an active inode
that stays around after it has been removed--until its final close
operation.  This means that the id shows up as free for reuse at a
time it should not be.

The effect of this was seen by Jens Rehpoehler, who:
    - had a filesystem mounted on an rbd device
    - unmapped that filesystem (without unmounting)
    - found that the mount still worked properly
    - but hit a panic when he attempted to re-map a new rbd device

This re-map attempt found the previously-unmapped id available.
The subsequent attempt to reuse it was met with a panic while
attempting to (re-)install the sysfs entry for the new mapped
device.

Fix this by holding off "putting" the rbd id, until the rbd_device
release function is called--when the last reference is finally
dropped.

Note: This fixes: http://tracker.newdream.net/issues/1907

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-03-22 10:47:50 -05:00
Alex Elder 593a9e7b34 rbd: small changes
Here is another set of small code tidy-ups:
    - Define SECTOR_SHIFT and SECTOR_SIZE, and use these symbolic
      names throughout.  Tell the blk_queue system our physical
      block size, in the (unlikely) event we want to use something
      other than the default.
    - Delete the definition of struct rbd_info, which is never used.
    - Move the definition of dev_to_rbd() down in its source file,
      just above where it gets first used, and change its name to
      dev_to_rbd_dev().
    - Replace an open-coded operation in rbd_dev_release() to use
      dev_to_rbd_dev() instead.
    - Calculate the segment size for a given rbd_device just once in
      rbd_init_disk().
    - Use the '%zd' conversion specifier in rbd_snap_size_show(),
      since the value formatted is a size_t.
    - Switch to the '%llu' conversion specifier in rbd_snap_id_show().
      since the value formatted is unsigned.

Signed-off-by: Alex Elder <elder@dreamhost.com>
2012-03-22 10:47:50 -05:00
Alex Elder 00f1f36ffa rbd: do some refactoring
A few blocks of code are rearranged a bit here:
    - In rbd_header_from_disk():
	- Don't bother computing snap_count until we're sure the
	  on-disk header starts with a good signature.
	- Move a few independent lines of code so they are *after* a
	  check for a failed memory allocation.
	- Get rid of unnecessary local variable "ret".
    - Make a few other changes in rbd_read_header(), similar to the
      above--just moving things around a bit while preserving the
      functionality.
    - In rbd_rq_fn(), just assign rq in the while loop's controlling
      expression rather than duplicating it before and at the end of
      the loop body.  This allows the use of "continue" rather than
      "goto next" in a number of spots.
    - Rearrange the logic in snap_by_name().  End result is the same.

Signed-off-by: Alex Elder <elder@dreamhost.com>
2012-03-22 10:47:50 -05:00
Alex Elder fed4c143ba rbd: fix module sysfs setup/teardown code
Once rbd_bus_type is registered, it allows an "add" operation via
the /sys/bus/rbd/add bus attribute, and adding a new rbd device that
way establishes a connection between the device and rbd_root_dev.
But rbd_root_dev is not registered until after the rbd_bus_type
registration is complete.  This could (in principle anyway) result
in an invalid state.

Since rbd_root_dev has no tie to rbd_bus_type we can reorder these
two initializations and never be faced with this scenario.

In addition, unregister the device in the event the bus registration
fails at module init time.

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-03-22 10:47:50 -05:00
Alex Elder 7ef3214af2 rbd: don't allocate mon_addrs buffer in rbd_add()
The mon_addrs buffer in rbd_add is used to hold a copy of the
monitor IP addresses supplied via /sys/bus/rbd/add.  That is
passed to rbd_get_client(), which never modifies it (nor do
any of the functions it gets passed to thereafter)--the mon_addr
parameter to rbd_get_client() is a pointer to constant data, so it
can't be modifed.  Furthermore, rbd_get_client() has the length of
the mon_addrs buffer and that is used to ensure nothing goes beyond
its end.

Based on all this, there is no reason that a buffer needs to
be used to hold a copy of the mon_addrs provided via
/sys/bus/rbd/add.   Instead, the location within that passed-in
buffer can be provided, along with the length of the "token"
therein which represents the monitor IP's.

A small change to rbd_add_parse_args() allows the address within the
buffer to be passed back, and the length is already returned.  This
now means that, at least from the perspective of this interface,
there is no such thing as a list of monitor addresses that is too
long.

Signed-off-by: Alex Elder <elder@dreamhost.com>
2012-03-22 10:47:50 -05:00
Alex Elder 5214ecc45c rbd: have rbd_parse_args() report found mon_addrs size
The argument parsing routine already computes the size of the
mon_addrs buffer it extracts from the "command."  Pass it to the
caller so it can use it to provide the length to rbd_get_client().

Signed-off-by: Alex Elder <elder@dreamhost.com>
2012-03-22 10:47:49 -05:00
Alex Elder 81a8979378 rbd: do a few checks at build time
This is a bit gratuitous, but there are a few things that can be
verified at build time rather than run time, so do that.

Signed-off-by: Alex Elder <elder@dreamhost.com>
2012-03-22 10:47:49 -05:00
Alex Elder e28fff268e rbd: don't use sscanf() in rbd_add_parse_args()
Make use of a few simple helper routines to parse the arguments
rather than sscanf().  This will treat both missing and too-long
arguments as invalid input (rather than silently truncating the
input in the too-long case).  In time this can also be used by
rbd_add() to use the passed-in buffer in place, rather than copying
its contents into new buffers.

It appears to me that the sscanf() previously used would not
correctly handle a supplied snapshot--the two final "%s" conversion
specifications were not separated by a space, and I'm not sure
how sscanf() handles that situation.  It may not be well-defined.
So that may be a bug this change fixes (but I didn't verify that).

The sizes of the mon_addrs and options buffers are now passed to
rbd_add_parse_args(), so they can be supplied to copy_token().

Signed-off-by: Alex Elder <elder@dreamhost.com>
2012-03-22 10:47:49 -05:00
Alex Elder a725f65e52 rbd: encapsulate argument parsing for rbd_add()
Move the code that parses the arguments provided to rbd_add() (which
are supplied via /sys/bus/rbd/add) into a separate function.

Also rename the "mon_dev_name" variable in rbd_add() to be
"mon_addrs".   The variable represents a list of one or more
comma-separated monitor IP addresses, each with an optional port
number.  I think "mon_addrs" captures that notion a little better.

Signed-off-by: Alex Elder <elder@dreamhost.com>
2012-03-22 10:47:48 -05:00
Alex Elder 27cc25943f rbd: simplify error handling in rbd_add()
If a couple pointers are initialized to NULL then a single
"out_nomem" label can be used for all of the memory allocation
failure cases in rbd_add().

Also, get rid of the "irc" local variable there.  There is no
real need for "rc" to be type ssize_t, and it can be used in
the spot "irc" was.

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-03-22 10:47:48 -05:00
Alex Elder 60571c7d55 rbd: reduce memory used for rbd_dev fields
The length of the string containing the monitor address
specification(s) will never exceed the length of the string passed
in to rbd_add().  The same holds true for the ceph + rbd options
string.  So reduce the amount of memory allocated for these to
that length rather than the maximum (1024 bytes).

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-03-22 10:47:48 -05:00
Alex Elder d720bcb0a8 rbd: have rbd_get_client() return a rbd_client
Since rbd_get_client() currently returns an error code.  It assigns
the rbd_client field of the rbd_device structure it is passed if
successful.  Instead, have it return the created rbd_client
structure and return a pointer-coded error if there is an error.
This makes the assignment of the client pointer more obvious at the
call site.

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-03-22 10:47:48 -05:00
Alex Elder f0f8cef5a3 rbd: a few simple changes
Here are a few very simple cleanups:
    - Add a "RBD_" prefix to the two driver name string definitions.
    - Move the definition of struct rbd_request below struct rbd_req_coll
      to avoid the need for an empty declaration of the latter.
    - Move and group the definitions of rbd_root_dev_release() and
      rbd_root_dev, as well as rbd_bus_type and rbd_bus_attrs[],
      close to the top of the file.  Arrange the latter so
      rbd_bus_type.bus_attrs can be initialized statically.
    - Get rid of an unnecessary local variable in rbd_open().
    - Rework some hokey logic in rbd_bus_add_dev(), so the value of
      "ret" at the end is either 0 or -ENOENT to avoid the need for
      the code duplication that was there.
    - Rename a goto target in rbd_add().

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-03-22 10:47:48 -05:00
Alex Elder 432b858749 rbd: rename "node_lock"
The spinlock used to protect rbd_client_list is named "node_lock".
Rename it to "rbd_client_list_lock" to make it more obvious what
it's for.

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-03-22 10:47:48 -05:00
Alex Elder bc534d86be rbd: move ctl_mutex lock inside rbd_client_create()
Since rbd_client_create() is only called in one place, move the
acquisition of the mutex around that call inside that function.

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-03-22 10:47:47 -05:00
Alex Elder d97081b0c7 rbd: move ctl_mutex lock inside rbd_get_client()
Since rbd_get_client() is only called in one place, move the
acquisition of the mutex around that call inside that function.

Furthermore, within rbd_get_client(), it appears the mutex only
needs to be held while calling rbd_client_create().  (Moving
the lock inside that function will wait for the next patch.)

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-03-22 10:47:47 -05:00
Alex Elder e6994d3dde rbd: release client list lock sooner
In rbd_get_client(), if a client is reused, a number of things
get done while still holding the list lock unnecessarily.

This just moves a few things that need no lock protection outside
the lock.

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-03-22 10:47:47 -05:00
Alex Elder d184f6bfde rbd: restore previous rbd id sequence behavior
It used to be that selecting a new unique identifier for an added
rbd device required searching all existing ones to find the highest
id is used.  A recent change made that unnecessary, but made it
so that id's used were monotonically non-decreasing.  It's a bit
more pleasant to have smaller rbd id's though, and this change
makes ids get allocated as they were before--each new id is one more
than the maximum currently in use.

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-03-22 10:47:47 -05:00
Alex Elder 499afd5b8e rbd: tie rbd_dev_list changes to rbd_id operations
The only time entries are added to or removed from the global
rbd_dev_list is exactly when a "put" or "get" operation is being
performed on a rbd_dev's id.  So just move the list management code
into get/put routines.

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-03-22 10:47:47 -05:00
Alex Elder e124a82f3c rbd: protect the rbd_dev_list with a spinlock
The rbd_dev_list is just a simple list of all the current
rbd_devices.  Using the ctl_mutex as a concurrency guard is
overkill.  Instead, use a spinlock for that specific purpose.

This also reduces the window that the ctl_mutex needs to be held in
rbd_add().

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-03-22 10:47:47 -05:00
Alex Elder 1ddbe94eda rbd: rework calculation of new rbd id's
In order to select a new unique identifier for an added rbd device,
the list of all existing ones is searched and a value one greater
than the highest id is used.

The list search can be avoided by using an atomic variable that
keeps track of the current highest id.  Using a get/put model for
id's we can limit the boundless growth of id numbers a bit by
arranging to reuse the current highest id once it gets released.
Add these calls to "put" the id when an rbd is getting removed.

Note that this changes the pattern of device id's used--new values
will never be below the highest one seen so far (even if there
exists an unused lower one).  I assert this is OK because the key
property of an rbd id is its uniqueness, not its magnitude.

Regardless, a follow-on patch will restore the old way of doing
things, I just think this commit just makes the incremental change
to atomics a little easier to understand.

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-03-22 10:47:47 -05:00
Alex Elder b7f23c361b rbd: encapsulate new rbd id selection
Move the loop that finds a new unique rbd id to use into
its own helper function.

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-03-22 10:47:47 -05:00
Josh Durgin cc9d734c3d rbd: use a single value of snap_name to mean no snap
There's already a constant for this anyway.

Since rbd_header_set_snap() is only used to set the rbd device
snap_name field, just do that within that function rather than
having it take the snap_name as an argument.

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>

v2: Changed interface rbd_header_set_snap() so it explicitly updates
    the snap_name in the rbd_device.  Also added a BUILD_BUG_ON()
    to verify the size of the snap_name field is sufficient for
    SNAP_HEAD_NAME.
2012-03-22 10:47:47 -05:00
Alex Elder 1dbb439913 rbd: do not duplicate ceph_client pointer in rbd_device
The rbd_device structure maintains a duplicate copy of the
ceph_client pointer maintained in its rbd_client structure.  There
appears to be no good reason for this, and its presence presents a
risk of them getting out of synch or otherwise misused.  So kill it
off, and use the rbd_client copy only.

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-03-22 10:47:47 -05:00
Alex Elder ee57741c52 rbd: make ceph_parse_options() return a pointer
ceph_parse_options() takes the address of a pointer as an argument
and uses it to return the address of an allocated structure if
successful.  With this interface is not evident at call sites that
the pointer is always initialized.  Change the interface to return
the address instead (or a pointer-coded error code) to make the
validity of the returned pointer obvious.

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-03-22 10:47:47 -05:00
Alex Elder 2107978668 rbd: a few small cleanups
Some minor cleanups in "drivers/block/rbd.c:
    - Use the more meaningful "RBD_MAX_OBJ_NAME_LEN" in place if "96"
      in the definition of RBD_MAX_MD_NAME_LEN.
    - Use DEFINE_SPINLOCK() to define and initialize node_lock.
    - Drop a needless (char *) cast in parse_rbd_opts_token().
    - Make a few minor formatting changes.

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-03-22 10:47:46 -05:00
Linus Torvalds 6c073a7ee2 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: fix safety of rbd_put_client()
  rbd: fix a memory leak in rbd_get_client()
  ceph: create a new session lock to avoid lock inversion
  ceph: fix length validation in parse_reply_info()
  ceph: initialize client debugfs outside of monc->mutex
  ceph: change "ceph.layout" xattr to be "ceph.file.layout"
2012-02-02 15:47:33 -08:00
Alex Elder d23a4b3fd6 rbd: fix safety of rbd_put_client()
The rbd_client structure uses a kref to arrange for cleaning up and
freeing an instance when its last reference is dropped.  The cleanup
routine is rbd_client_release(), and one of the things it does is
delete the rbd_client from rbd_client_list.  It acquires node_lock
to do so, but the way it is done is still not safe.

The problem is that when attempting to reuse an existing rbd_client,
the structure found might already be in the process of getting
destroyed and cleaned up.

Here's the scenario, with "CLIENT" representing an existing
rbd_client that's involved in the race:

 Thread on CPU A                | Thread on CPU B
 ---------------                | ---------------
 rbd_put_client(CLIENT)         | rbd_get_client()
   kref_put()                   |   (acquires node_lock)
     kref->refcount becomes 0   |   __rbd_client_find() returns CLIENT
     calls rbd_client_release() |   kref_get(&CLIENT->kref);
                                |   (releases node_lock)
       (acquires node_lock)     |
       deletes CLIENT from list | ...and starts using CLIENT...
       (releases node_lock)     |
       and frees CLIENT         | <-- but CLIENT gets freed here

Fix this by having rbd_put_client() acquire node_lock.  The result
could still be improved, but at least it avoids this problem.

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-02-02 12:56:59 -08:00
Alex Elder 97bb59a03d rbd: fix a memory leak in rbd_get_client()
If an existing rbd client is found to be suitable for use in
rbd_get_client(), the rbd_options structure is not being
freed as it should.  Fix that.

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-02-02 12:49:27 -08:00
Alex Elder 0e805a1d85 rbd: initialize snap_rwsem in rbd_add()
New rbd device structures get initialized in rbd_add().  Many of
the fields rely on being initially zero-filled.  However we lockdep
was noticing that the rw_semaphore embedded in the header field
was not getting properly initialized.  Fix that.

Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2012-01-12 11:00:50 -08:00
Josh Durgin 51703306b3 rbd: remove buggy rollback functionality
This doesn't interact with resizing well, since it doesn't set the
size of the device to the size at the snapshot. It's also an expensive
operation to be synchronous. Rollback can still be done with the
userspace rbd tool.

Signed-off-by: Josh Durgin <josh.durgin@dreamhost.com>
2011-12-07 10:46:19 -08:00
Josh Durgin 81e759fbf7 rbd: return an error when an invalid header is read
This protects against opening future rbd images that have incompatible format changes.

Signed-off-by: Josh Durgin <josh.durgin@dreamhost.com>
2011-12-07 10:46:10 -08:00
Linus Torvalds 97d2eb13a0 Merge branch 'for-linus' of git://ceph.newdream.net/git/ceph-client
* 'for-linus' of git://ceph.newdream.net/git/ceph-client:
  libceph: fix double-free of page vector
  ceph: fix 32-bit ino numbers
  libceph: force resend of osd requests if we skip an osdmap
  ceph: use kernel DNS resolver
  ceph: fix ceph_monc_init memory leak
  ceph: let the set_layout ioctl set single traits
  Revert "ceph: don't truncate dirty pages in invalidate work thread"
  ceph: replace leading spaces with tabs
  libceph: warn on msg allocation failures
  libceph: don't complain on msgpool alloc failures
  libceph: always preallocate mon connection
  libceph: create messenger with client
  ceph: document ioctls
  ceph: implement (optional) max read size
  ceph: rename rsize -> rasize
  ceph: make readpages fully async
2011-10-28 16:42:18 -07:00
Sage Weil 6ab00d465a libceph: create messenger with client
This simplifies the init/shutdown paths, and makes client->msgr available
during the rest of the setup process.

Signed-off-by: Sage Weil <sage@newdream.net>
2011-10-25 16:10:15 -07:00
Jiri Kosina e060c38434 Merge branch 'master' into for-next
Fast-forward merge with Linus to be able to merge patches
based on more recent version of the tree.
2011-09-15 15:08:18 +02:00
Justin P. Mattock 699324871f treewide: remove extra semicolons from various parts of the kernel
This is a resend from the original, changing the title from PATCH to
RFC(since this is a review for commit, and I should have put that the first go around).
and also removing some of the commit's with ia64 and bash since it is significant.
let me know if I might have missed anything etc..

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-09-15 14:50:49 +02:00
Josh Durgin 029bcbd8b0 rbd: set blk_queue request sizes to object size
This improves performance since more requests can be merged.

Reviewed-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Josh Durgin <josh.durgin@dreamhost.com>
2011-07-26 11:29:35 -07:00
Yehuda Sadeh 79e3057c4c rbd: cancel watch request when releasing the device
We were missing this cleanup, so when a device was released
the osd didn't clean up its watchers list, so following notifications
could be slow as osd needed to timeout on the client.

Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
2011-07-26 11:29:04 -07:00
Sage Weil 9db4b3e327 rbd: handle online resize of underlying rbd image
If we get a notification that the image header has changed, check for
a change in the image size.

Signed-off-by: Sage Weil <sage@newdream.net>
2011-05-24 11:52:08 -07:00
Sage Weil aedfec59ee rbd: use snprintf for disk->disk_name
Signed-off-by: Sage Weil <sage@newdream.net>
2011-05-24 11:52:03 -07:00
Sage Weil 916d4d6727 rbd: cleanup: make kfree match kmalloc
Signed-off-by: Sage Weil <sage@newdream.net>
2011-05-24 11:52:01 -07:00
Sage Weil 13143d2d1c rbd: warn on update_snaps failure on notify
Signed-off-by: Sage Weil <sage@newdream.net>
2011-05-19 11:25:05 -07:00
Yehuda Sadeh 1fec70932d rbd: fix split bio handling
The rbd driver currently splits bios when they span an object boundary.
However, the blk_end_request expects the completions to roll up the results
in block device order, and the split rbd/ceph ops can complete in any
order.  This patch adds a struct rbd_req_coll to track completion of split
requests and ensures that the results are passed back up to the block layer
in order.

This fixes errors where the file system gets completion of a read operation
that spans an object boundary before the data has actually arrived.  The
bug is easily reproduced with iozone with a working set larger than
available RAM.

Reported-by: Fyodor Ustinov <ufm@ufm.su>
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>
2011-05-13 13:52:57 -07:00
Sage Weil 11f770027b rbd: fix leak of ops struct
The ops vector must be freed by the rbd_do_request caller.

Signed-off-by: Sage Weil <sage@newdream.net>
2011-05-12 20:59:14 -07:00
Sage Weil 4ad12621e4 libceph: fix ceph_osdc_alloc_request error checks
ceph_osdc_alloc_request returns NULL on failure.

Signed-off-by: Sage Weil <sage@newdream.net>
2011-05-03 09:28:13 -07:00
Yehuda Sadeh 59c2be1e4d rbd: use watch/notify for changes in rbd header
Send notifications when we change the rbd header (e.g. create a snapshot)
and wait for such notifications.  This allows synchronizing the snapshot
creation between different rbd clients/rools.

Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>
2011-03-22 11:33:56 -07:00
Yehuda Sadeh 766fc43973 rbd: fix cleanup when trying to mount inexistent image
Previously we didn't clean up the sysfs entry that was just
created.

Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>
2011-01-12 15:15:18 -08:00
Yehuda Sadeh dfc5606dc5 rbd: replace the rbd sysfs interface
The new interface creates directories per mapped image
and under each it creates a subdir per available snapshot.
This allows keeping a cleaner interface within the sysfs
guidelines. The ABI documentation was updated too.

Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>
2010-12-01 15:53:22 -08:00
Dan Carpenter 85b5aaa624 rbd: passing wrong variable to bvec_kunmap_irq()
We should be passing "buf" here insead of "bv".  This is tricky because
it's not the same as kmap() and kunmap().  GCC does warn about it if you
compile on i386 with CONFIG_HIGHMEM.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sage Weil <sage@newdream.net>
2010-10-20 15:38:25 -07:00