The i2c_imx_trx_complete() function is using
wait_event_interruptible_timeout() to wait for the I2C controller to
signal that it has completed an I2C bus operation. If the process that
causes the I2C operation receives a signal, the wait will be
interrupted, returning an error. It is better to let the I2C operation
finished before handling the signal (i.e. returning into userspace).
It is safe to use wait_event_timeout() instead, because the timeout
will allow the process to exit if the I2C bus hangs. It's also better
to allow the I2C operation to finish, because unacknowledged I2C
operations can cause the I2C bus to hang.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch is an improvement to 4bba0fd8d1
which got to mainline a little early.
Sudhakar Rajashekhara explains that at least OMAP-L138 requires MDR mode
settings before DXR for correct behaviour, so load MDR first with
STT cleared and later load again with STT set.
Tested on DM355 connected to Techwell TW2836 and Wolfson WM8985
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
of/i2c: Fix module load order issue caused by of_i2c.c
i2c: Fix checks which cause legacy suspend to never get called
i2c-pca: Fix waitforcompletion() return value
i2c: Fix for suspend/resume issue
i2c: Remove obsolete cleanup for clientdata
S3C2440 style I2C controller uses PCLK to calculate the SDA line delay.
The driver wrongly assumed that this delay is calculated from the
frequency that the controller is operating on. This patch fixes this
issue.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit 959e85f7, "i2c: add OF-style registration and binding" caused a
module dependency loop where of_i2c.c calls functions in i2c-core, and
i2c-core calls of_i2c_register_devices() in of_i2c. This means that
when i2c support is built as a module when CONFIG_OF is set, then
neither i2c_core nor of_i2c are able to be loaded.
This patch fixes the problem by moving the of_i2c_register_devices()
calls back into the device drivers. Device drivers already
specifically request the core code to parse the device tree for
devices anyway by setting the of_node pointer, so it isn't a big
deal to also call the registration function. The drivers just become
slightly more verbose.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
ret is still -1, if during the polling read_byte() returns at once
with I2C_PCA_CON_SI set. So ret > 0 would lead *_waitforcompletion()
to return 0, in spite of the proper behavior.
The routine was rewritten, so that ret has always a proper value,
before returning.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When setting up to transmit, a race exists between the ISR and
i2c_davinci_xfer_msg() trying to load the first byte and adjust counters.
This is mostly visible for transmits > 1 byte long.
The hardware starts sending immediately that MDR is loaded. IMR trickery
doesn't work because if we start sending, finish the first byte and an
XRDY event occurs before we load IMR to unmask it, we never get an
interrupt, and we timeout.
Move the MDR load after DXR,IMR loads to avoid this race without locking.
Tested on DM355 connected to Techwell TW2836 and Wolfson WM8985
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
It doesn't make sense to set result to -ETIMEDOUT but return 0 (success)
afterwards. Since there's code in octeon_i2c_start() to handle the
error, it should be called.
Signed-off-by: Bernhard Walle <walle@corscience.de>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
If the i2c bus receives an interrupt with both BB (bus busy) and
ARDY (register access ready) statuses set during the tranfer of the last message
the bus was put to idle while still busy.
This caused bus to timeout.
Signed-off-by: Mathias Nyman <mathias.nyman@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'for-linus/i2c-2636' of git://git.fluff.org/bjdooks/linux:
i2c/nuc900: add i2c driver support for nuc900
i2c: Enable NXP LPC support in Kconfig
i2c-pxa: fix compiler warning, due to missing const
i2c: davinci: bus recovery procedure to clear the bus
i2c: davinci: Add cpufreq support
i2c: davinci: Add suspend/resume support
i2c: davinci: Add helper functions for power management
i2c: davinci: misc. cleanups: remove MOD_REG_BIT and IO_ADDRESS usage
i2c: davinci: Fix smbus Oops with AIC33 usage
This patch is to add i2c driver support for nuc900.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
NXP LPC series processors use the IP3204 I2C block shared with the
Philips PNX4008 processor.
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds the missing const to "struct platform_device_id" to fix
this warning:
/home/frogger/pengutronix/linux/linux-2.6/drivers/i2c/busses/i2c-pxa.c:
In function 'i2c_pxa_probe':
/home/frogger/pengutronix/linux/linux-2.6/drivers/i2c/busses/i2c-pxa.c:1004:
warning: initialization discards qualifiers from pointer target type
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Roel Kluin <roel.kluin@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (63 commits)
of/platform: Register of_platform_drivers with an "of:" prefix
of/address: Clean up function declarations
of/spi: call of_register_spi_devices() from spi core code
of: Provide default of_node_to_nid() implementation.
of/device: Make of_device_make_bus_id() usable by other code.
of/irq: Fix endian issues in parsing interrupt specifiers
of: Fix phandle endian issues
of/flattree: fix of_flat_dt_is_compatible() to match the full compatible string
of: remove of_default_bus_ids
of: make of_find_device_by_node generic
microblaze: remove references to of_device and to_of_device
sparc: remove references to of_device and to_of_device
powerpc: remove references to of_device and to_of_device
of/device: Replace of_device with platform_device in includes and core code
of/device: Protect against binding of_platform_drivers to non-OF devices
of: remove asm/of_device.h
of: remove asm/of_platform.h
of/platform: remove all of_bus_type and of_platform_bus_type references
of: Merge of_platform_bus_type with platform_bus_type
drivercore/of: Add OF style matching to platform bus
...
Fix up trivial conflicts in arch/microblaze/kernel/Makefile due to just
some obj-y removals by the devicetree branch, while the microblaze
updates added a new file.
Come out of i2c time out condition by following the
bus recovery procedure outlined in the i2c protocol v3 spec.
The kernel must be robust enough to gracefully recover
from i2c bus failure without having to reset the machine.
This is done by first NACKing the slave, pulsing the SCL
line 9 times and then sending the stop command.
This patch has been tested on a DM6446 and DM355
Signed-off-by: Philby John <pjohn@in.mvista.com>
Signed-off-by: Srinivasan, Nageswari <nageswari@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Add cpufreq support for DaVinci I2C driver.
Tested on DA850/OMAP-L138 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Add suspend and resume callbacks to DaVinci I2C driver.
This has been tested on DA850/OMAP-L138 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Add i2c reset control and clock divider calculation functions
which will be useful for power management features.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cleanup the DaVinci I2C driver. Remove MOD_REG_BIT macro.
Also use ioremap instead of IO_ADDRESS macro.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
This fixes Oops at kernel startup while "scanning" for TLV320AIC23IDx
addresses.
Additional fix from Sudhakar Rajashekhara: I think 'first byte set'
should come after the write because an I2C transaction is being
carried out before configuring the I2C mode register (which has bits
to configure Master, Start condition etc), which causes undefined
behavior.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Alexander Vasiliev <alexvasiljev@gmail.com>
Signed-off-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds HAVE_S3C2410_I2C to control inclusion of I2C bus driver
on Samsung SoCs and makes I2C bus driver dependency SoC specific instead
of machine specific. This will enalbe all machines using Samsung ARCH_S3C2410,
_S3C64XX, _S5P6440, _S5PC100, and _S5PV210 to select the I2C driver by default
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
This patch improves the recovery of the MPC's I2C bus from errors like bus
hangs resulting in timeouts:
1. make the bus timeout configurable, as it depends on the bus clock and
the attached slave chip(s); default is still 1 second;
2. detect any of the cases indicated by the CF, BB and RXAK MSR flags if a
timeout occurs, and add a missing (required) MAL reset;
3. use a more reliable method to fixup the bus if a hang has been detected.
The sequence is sent 9 times which seems to be necessary if a slave
"misses" more than one clock cycle. For 400 kHz bus speed, the fixup is
also ~70us (81us vs. 150us) faster.
Tested on a custom Lite5200b derived board, with a Dallas RTC, AD sensors
and NXP IO expander chips attached to the i2c.
Changes vs. v1:
- use improved bus fixup sequence for all chips (not only the 5200)
- calculate real clock from defaults if no clock is given in the device tree
- better description (I hope) of the changes.
I didn't split the changes in this file into three parts as recommended by
Grant, as they actually belong together (i.e. they address one single
problem, just in three places of one single source file).
Signed-off-by: Albrecht Dreß <albrecht.dress@arcor.de>
[grant.likely@secretlab.ca: fixup for ->node to ->dev.of_node transition]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: Fix autoloading of fschmd on recent Fujitsu machines
hwmon: (coretemp) Properly label the sensors
hwmon: (coretemp) Skip duplicate CPU entries
hwmon: (it87) Fix in7 on IT8720F
hwmon: (k8temp) Fix temperature reporting for ASB1 processor revisions
Sibyte i2c bus driver returns non-descriptive error values.
Update to return error values as defined in Documentation/i2c/fault-codes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fujitsu slightly changed the DMI strings in their recent machines,
(for example the D2778) and this breaks the automatic loading of the
needed fschmd driver. Being more tolerant on string comparison fixes
the issue.
This closes bug #15634:
https://bugzilla.kernel.org/show_bug.cgi?id=15634
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Sergey Spiridonov <sena@hurd.homeunix.org>
Cc: Hans de Goede <hdegoede@redhat.com>
This patch adds OF hooks to the i2c core so that devices can automatically
be registered based on device tree data.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch cleans up the i2c OF support code to make it selectable by
all architectures and allow for automatic registration of i2c devices.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
The ACPI subsystem strictly checks for resource conflicts. When there's
a conflict, it outputs a warning message with all the details needed to
properly diagnose the underlying issue. However, the i2c-nforce2 driver
also prints its own message. Not only is the message redundant, it is at
the KERN_ERR level, which overrides some bootsplash screens for no good
reason. This change removes the two lines that print out the error
messages.
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As warned by checkpatch.pl, <linux/io.h> should be used instead of
<asm/io.h>.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
GPIO driven I2C bus can be used for controlling the PMIC chip. The
example of such configuration is Samsung Aquila board.
This patch moves initialization code to subsys_initcall() to ensure
that the i2c bus is available early so the regulators can be quickly
probed and available for other devices on their probe() call.
Such solution has been proposed by Mark Brown to fix the problem of
the regulators not beeing available on the peripheral device probe():
http://lists.infradead.org/pipermail/linux-arm-kernel/2010-March/011971.html
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It is easier to adjust the flags when you know their default value.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Make PCI device ids constant as we just did for many other i2c bus
drivers already.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Márton Németh <nm127@freemail.hu>
Fix all checkpatch warnings. No functional changes are made.
Signed-off-by: Ivo Manca <pinkel@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
