If we encounter a situation where the CPU blocks waiting for results
from the GPU, give the GPU a kick to boost its the frequency.
This should work to reduce user interface stalls and to quickly promote
mesa to high frequencies - but the cost is that our requested frequency
stalls high (as we do not idle for long enough before rc6 to start
reducing frequencies, nor are we aggressive at down clocking an
underused GPU). However, this should be mitigated by rc6 itself powering
off the GPU when idle, and that energy use is dependent upon the workload
of the GPU in addition to its frequency (e.g. the math or sampler
functions only consume power when used). Still, this is likely to
adversely affect light workloads.
In particular, this nearly eliminates the highly noticeable wake-up lag
in animations from idle. For example, expose or workspace transitions.
(However, given the situation where we fail to downclock, our requested
frequency is almost always the maximum, except for Baytrail where we
manually downclock upon idling. This often masks the latency of
upclocking after being idle, so animations are typically smooth - at the
cost of increased power consumption.)
Stéphane raised the concern that this will punish good applications and
reward bad applications - but due to the nature of how mesa performs its
client throttling, I believe all mesa applications will be roughly
equally affected. To address this concern, and to prevent applications
like compositors from permanently boosting the RPS state, we ratelimit the
frequency of the wait-boosts each client recieves.
Unfortunately, this techinique is ineffective with Ironlake - which also
has dynamic render power states and suffers just as dramatically. For
Ironlake, the thermal/power headroom is shared with the CPU through
Intelligent Power Sharing and the intel-ips module. This leaves us with
no GPU boost frequencies available when coming out of idle, and due to
hardware limitations we cannot change the arbitration between the CPU and
GPU quickly enough to be effective.
v2: Limit each client to receiving a single boost for each active period.
Tested by QA to only marginally increase power, and to demonstrably
increase throughput in games. No latency measurements yet.
v3: Cater for front-buffer rendering with manual throttling.
v4: Tidy up.
v5: Sadly the compositor needs frequent boosts as it may never idle, but
due to its picking mechanism (using ReadPixels) may require frequent
waits. Those waits, along with the waits for the vrefresh swap, conspire
to keep the GPU at low frequencies despite the interactive latency. To
overcome this we ditch the one-boost-per-active-period and just ratelimit
the number of wait-boosts each client can receive.
Reported-and-tested-by: Paul Neumann <paul104x@yahoo.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68716
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Cc: Stéphane Marchesin <stephane.marchesin@gmail.com>
Cc: Owen Taylor <otaylor@redhat.com>
Cc: "Meng, Mengmeng" <mengmeng.meng@intel.com>
Cc: "Zhuang, Lena" <lena.zhuang@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: No extern for function prototypes in headers.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we switched to always using a timeout in conjunction with
wait_seqno, we lost the ability to detect missed interrupts. Since, we
have had issues with interrupts on a number of generations, and they are
required to be delivered in a timely fashion for a smooth UX, it is
important that we do log errors found in the wild and prevent the
display stalling for upwards of 1s every time the seqno interrupt is
missed.
Rather than continue to fix up the timeouts to work around the interface
impedence in wait_event_*(), open code the combination of
wait_event[_interruptible][_timeout], and use the exposed timer to
poll for seqno should we detect a lost interrupt.
v2: In order to satisfy the debug requirement of logging missed
interrupts with the real world requirments of making machines work even
if interrupts are hosed, we revert to polling after detecting a missed
interrupt.
v3: Throw in a debugfs interface to simulate broken hw not reporting
interrupts.
v4: s/EGAIN/EAGAIN/ (Imre)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Don't use the struct typedef in new code.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We missed adding a few cleanup steps for recent additions.
Reviewer: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch attempts to clean up the ring/IA scaling programming in the
following ways.
1. Fix the comment about the DDR frequency. The math is 266MHz, not
133MHz. Formula was right, docs are wrong.
2. Mask the DCLK register since I don't know how it is defined on future
platforms.
3. use mult_frac instead of magic math.
This helps for future platform enabling.
v2: Actually use the right patch. The v1 was a mix of things, none of
which was right. Note that due to rounding, we actually get different
values (slightly higher) for the effective ring frequency.
v3: Use 1.25 instead of 1.33 as the original code did. (Jesse)
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we ever end up doing the retry loop due to bandwidth constraints, we
would rewrite pipe_src_{w,n} based on adjusted_mode timings. But by that
time the encoder may have already replaced the adjusted_mode with a
fixed panel mode, which would then corrupt pipe_src_{w,h}.
v2: Use requested_mode and slap on a big comment from Daniel
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This workaround is described in the mode set sequence documentation.
When enabling planes for the second pipe, we need to wait for 2
vblanks on the first pipe. This should solve "a flash of screen
corruption if planes are enabled on second/third pipe during the time
that big FIFO mode is exiting". Watermarks are fun :)
v2: Save indentation levels
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Refactor the plane enabling/disabling into helper functions and move
the calls to happen as the first thing during .crtc_disable, and the
last thing during .crtc_enable.
Those are the two clear points where we are sure that the pipe is
actually running regardless of the encoder type or hardware
generation.
v2: Made by Paulo:
Remove the code touching everything but the Haswell functions. We
need this change on Haswell right now since it fixes a FIFO underrun
that we get on pipe A while we enable pipe B (see the workaround
notes on the Haswell mode set sequence documentation). We can bring
back the code to gens 2-7 later, once they're tested.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The global integrated clock source bit resides in DPLL B on VLV, but we
were treating it as a per-pipe resource. It needs to be set whenever
any PLL is active, so pull setting the bit out of vlv_update_pll and
into vlv_enable_pll. Also add a vlv_disable_pll to prevent disabling it
when pipe B shuts down.
I'm guessing on the references here, I expect this to bite any config
where multiple displays are active or displays are moved from pipe to
pipe.
v2: re-add bits in vlv_update_pll to keep from confusing the state checker
v3: use enum pipe checks (Daniel)
set CRI clock source early (Ville)
consistently set CRI clock source everywhere (Ville)
v4: drop unnecessary setting of bit in vlv enable pll (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=67245
References: https://bugs.freedesktop.org/show_bug.cgi?id=69693
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: s/1/PIPE_B/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For some reason, every single time I try to run module_reload
something tries to read the connector sysfs files. This happens
after we destroy the encoders and before we destroy the connectors, so
when the sysfs read triggers the connector detect() function,
intel_conector->encoder points to memory that was already freed.
The bad backtrace is just:
[<ffffffff8163ca9a>] dump_stack+0x54/0x74
[<ffffffffa00c2c8e>] intel_dp_detect+0x1e/0x4b0 [i915]
[<ffffffffa001913d>] status_show+0x3d/0x80 [drm]
[<ffffffff813d5340>] dev_attr_show+0x20/0x60
[<ffffffff81221f50>] ? sysfs_read_file+0x80/0x1b0
[<ffffffff81221f79>] sysfs_read_file+0xa9/0x1b0
[<ffffffff811aaf1e>] vfs_read+0x9e/0x170
[<ffffffff811aba4c>] SyS_read+0x4c/0xa0
[<ffffffff8164e392>] system_call_fastpath+0x16/0x1b
But if you add tons of memory checking debug options to your Kernel
you'll also see:
- general protection fault: 0000
- BUG kmalloc-4096 (Tainted: G D W ): Poison overwritten
- INFO: Allocated in intel_ddi_init+0x65/0x270 [i915]
- INFO: Freed in intel_dp_encoder_destroy+0x69/0xb0 [i915]
Among a bunch of other error messages.
So this commit just destroys the sysfs files before both the encoder
and connectors are freed.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Neither the DP spec nor the compliance test spec state or imply that we
should write the DP_TRAINING_PATTERN_SET at every voltage swing and
pre-emphasis change. Indeed we probably shouldn't. So don't.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49402
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Smoke-tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Per DP1.2 spec.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It indicates a probable BIOS bug, but it appears to be harmless, and
there's nothing the user can do about it anyway, so reduce to a debug
msg. I've filed a bug with the BIOS folks about it anyway, so hopefully
they'll fix whatever GT SB read they were doing when the GT was off.
References: https://bugs.freedesktop.org/show_bug.cgi?id=69396
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The kernel shouldn't accept invalid modes, just say No.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the coding of stereo layout has changed from a bit field to an
enum, we need remove that check.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows us to use fewer bits in the mode structure, leaving room for
future work while allowing more stereo layouts types than we could have
ever dreamt of.
I also exposed the previously private DRM_MODE_FLAG_3D_MASK to set in
stone that we are using 5 bits for the stereo layout enum, reserving 32
values.
Even with that reservation, we gain 3 bits from the previous encoding.
The code adding the mandatory stereo modes needeed to be adapted as it was
relying or being able to or stereo layouts together.
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to use the clock control reg to figure out how many CZ clks are in
30ns and use that as the basis for our RC6 residency calculations.
v2: use ULL everywhere for consistency (Chris)
factor out bias for clarity (Chris)
References: https://bugs.freedesktop.org/show_bug.cgi?id=69692
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And add some reg defines while we're at it. Since the units of the RC6
residency counter are actually in CZ clocks, we want to just use the
high bits or we'll overflow too frequently.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
vlv_find_best_dpll() has an open coded DIV_ROUND_CLOSEST(). Replace it
with the real thing.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use 'continue' to get rid of one indent level in vlv_find_best_dpll()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CDCLK is used to generate the gmbus clock. This is normally done by
BIOS. Program the value if the BIOS-less system doesn't do it.
v2: Move this to intel_i2c_reset to allow reprogram the gmbus frequency
during resume. (Daniel)
v3: Change GMBUS_FREQ to GMBUSFREQ_VLV, and use VLV_DISPLAY_BASE.
(Ville).
Remove cdclk_ratio[] table, and calculate the cdclk ratio instead.
(Ville).
Change the shift then mask for reg read, to mask first, then shift.
(Ville).
Remove the gmbus frequency calculation = cdclk/1.01. Based on BIOS
programming, gmbus frequency = cdclk frequency. (Ville)
Add get_disp_clk_div, which can use to get cdclk/czclk divide.
v4: Fix the mmio_offset base for CZCLK_CDCLK_FREQ_RATIO, gmbus_freq
calculation, and duplicate check for gmbus_freq. (Ville)
In VLV, the spec is wrong about 4Mhz reference frequency for GMBUS. It
should be 1Mhz.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[danvet: Add the comment Ville suggested. Also appease checkpatch a
bit.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Still digging up the actual VBT info for this, but wanted to get this
out there for testing, or in case others are also bugged by this.
This can happen if you boot with an external display connected. In that
case, the attached eDP backlight modulation frequency may not be
programmed, so we need to use something (in this case the value my BIOS
normally programs with just the internal display enabled).
v2: fix masking and magic value in read_blc_pwm_ctl (Jani)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67732
Tested-by: shui yangwei <yangweix.shui@intel.com> (v1)
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we ask to adjust the crtc timings for stereo modes, the correct
pipe_src_w and pipe_src_h can be found in crtc_vdisplay and crtc_hdisplay.
v2: Add comment about why pipe_src_w/h need to be set afert
set_crtcinfo() (Daniel Vetter)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When scanning out big stereo buffers that are actually bigger that their
natural 2D counterpart, we need to blow up the crtc timings as well.
Not that this is only done for frame packing as this is the only stereo
mode currently exposed needing this kind of ajdustements.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
struct drm_mode_display now has a separate crtc_ version of the clock to
be used when we're talking about the timings given to the harwadre (was
far as the mode is concerned).
This commit is really the result of a git grep adjusted_mode.*clock and
replacing those by adjusted_mode.crtc_clock. No functional change.
v2: Rebased on drm-intel-queued-next
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to dump the parameters given to the hardware, so let's use
crtc_clock here.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some stereo modes, like frame packing, need a larger CRTC viewport than
the "natural" underlying 2D mode and thus drm_crtc_check_viewport()
needs to query the adjusted mode to use the correct h/vdisplay.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both setcrtc and page_flip are checking that the framebuffer is big
enough for the defined crtc viewport (x, y, hdisplay, vdisplay). Factor
that code out in a single function.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When using the frame packing and a single big framebuffer, some hardware
requires that we do everything like if we were scanning out the big
buffer itself. Let's instrument drm_mode_set_crtcinfo() to be able to do
this adjustement if the driver is asking for it.
v2: Use crtc_vtotal and multiply the clock by 2 instead of
reconstructing it (Ville Syrjälä)
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like the various timings, make it possible to have a clock field
what we can tweak before giving it to hardware.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This field is unused. Garbage collect it.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This field was only accessed by the nouveau driver, but never set. So
concluded we can rid of this one.
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like with interlaced or double scan modes, make stereo modes a
per-connector opt-in to give a chance to driver authors to make it work
before enabling it.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows to expose the alternate clock versions of the stereo modes.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When scanning out a stereo mode, the AVI infoframe vic field has to be
the underlyng 2D VIC. Before that commit, we weren't matching the CEA
mode because of the extra stereo flag and then were setting the VIC
field in the AVI infoframe to 0.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When scanning out a 3D mode on HDMI, we need to send an HDMI infoframe
with the corresponding layout to the sink.
v2: Make s3d_structure_from_display_mode() less subtle (Ville Syrjälä)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When setting a stereo 3D mode, there can be only one bit set describing
the layout of the frambuffer(s). So reject invalid modes early.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So we respect a nice design of having similar functions at the same
level, in this case:
do_hdmi_vsdb_modes()
- add_hdmi_mandatory_stereo_modes()
- add_hdmi_mode()
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For now, let's just look at the 3D_present flag of the CEA HDMI vendor
block to detect if the sink supports a small list of then mandatory 3D
formats.
See the HDMI 1.4a 3D extraction for detail:
http://www.hdmi.org/manufacturer/specification.aspx
v2: Rename freq to vrefresh, make the mandatory structure a bit more
compact, fix some white space issues and add a couple of const
(Ville Syrjälä)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This capability allows user space to control the delivery of modes with
the 3D flags set. This is to not play games with current user space
users not knowing anything about stereo 3D flags and that could try
to set a mode with one or several of those bits set.
So, the plan is to remove the stereo modes from the list of modes we
give to DRM clients by default, and let them through if we are being
told otherwise.
stereo_allowed is bound to the drm_file structure to make it a
per-client setting, not a global one.
v2: Replace clearing 3D flags by discarding the stereo modes now that
they are regular modes.
v3: SET_CAP -> SET_CLIENT_CAP rename (Chris Wilson)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HDMI 1.4a defines a few layouts that we'd like to expose. This commits
add new modeinfo flags that can be used to list the supported stereo
layouts (when querying the list of modes) and to set a given stereo 3D
mode (when setting a mode).
v2: Add a drm_mode_is_stereo() helper
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This ioctl can be used to turn some knobs in a DRM driver. The client
can ask the DRM core for an alternate view of the reality: it can be
useful to be able to instruct the core that the DRM client can handle
new functionnality that would otherwise break current ABI.
v2: Rename to ioctl from SET_CAP to SET_CLIENT_CAP (Chris Wilson)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's a tiny bit more logical to find the different capabilities you can
use with the GET_CAP ioctl next to the structure rather than putting
them at the end of the file.
v2: Tab align the litterals (David Herrmann)
v3: Make it clearer that DRM_PRIME_CAP_EXPORT/IMPORT are flags of
DRM_CAP_PRIME.
v4: Rebase on top of latest bits (DRM_CAP_ASYNC_PAGE_FLIP was
introduced)
Reviewed-by: David Herrmann <dh.herrmann@gmail.com> (for v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With some divider values we end up with the wrong result. So remove the
intermediates (like Ville suggested in the first place) to get the right
answer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Calculation is a little different than other platforms.
v2: update to use port_clock instead
rebase on top of Ville's changes
v3: update to new port_clock semantics - don't divide by
pixel_multiplier (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=67345
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So that we can find the callers who introduce a ring stall. A single
ring stall is not too unwelcome, the right issue becomes when they start
to interlock and prevent any concurrent work. That, however, is a little
tricker to detect with a mere tracepoint!
v2: Rebrand it as a ring event, rather than an object event.
v3: Include the seqno in the tracepoint for posterity or something.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add the missing cache-level to the describe_obj() function for debug and
error reporting.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the typo in previous commit for DP 1.62 divisor.
drm/i915: Move Valleyview DP DPLL divisor calc to intel_dp_set_clock v2
v2: sigh, the m1 div is 3.
Reported-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
