stop sched scan isn't an immediate operation
and we need to wait for PERIODIC_SCAN_COMPLETE_EVENT_ID
after sending a stop before changing internal state
and notifying upper layers.
Not doing this caused problems when canceling an existing sched
scan and immediately requesting to start a new one
with a different configuration as the FW was still
in the middle of the previous sched scan.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
DFS channels weren't scanned properly because
min/max_duration weren't set for these channels
even though they're required by the FW.
The change sets passive_duration and min/max_duration
for all channels as the FW uses the correct parameters
according to the channel type.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The current wl1271_dev_notify implementation sets the
new operstate to all associated stations (while only
a specific vif was changed).
Until we'll have a method to get the actual vif from
the given dev, check the current operstate of each vif.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When removing a sta/ibss role, the device role has to
stopped (and disabled) as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
dev_role_id only indicates whether the dev role
is enabled, not started (e.g. on IBSS merge,
the device role is enabled, but not started).
Checking for any role in ROC (in order to determine
whether dev role was started) is wrong as well,
especially in multi-vif env.
Check for started dev role only by checking the dev_hlid.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
During sta disconnection, a deauth packet is being queued to
the dev role queue. However, the dev role is being stopped
before the packet was sent.
Flush the tx queue before stopping the dev role.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This flag should be set per-vif, rather than globally.
Rename the flag to indicate IN_USE (rather than IDLE), as
in the default configuration (i.e. flag is clear) the vif
should be idle.
Change all the bit operations (and elp conditions) appropriately.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Since the conf_tx callback passes the vif as param,
we must have been added first (and mac80211 verifies it).
Remove the handling of such case.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Implement the change_interface callback by simply removing the
current vif and adding a new one after updating the vif type.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When compiling wl12xx for x86, there was a warning complaining about
the size of the buffer we were allocating in the stack:
drivers/net/wireless/wl12xx/debugfs.c: In function 'driver_state_read':
drivers/net/wireless/wl12xx/debugfs.c:380:1: warning: the frame size of 1040 bytes is larger than 1024 bytes
To prevent this, allocate the buffer in the heap instead.
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl1271_configure_suspend_sta leaves a stale stack declared
completion in wlvif->ps_compl. Set it to NULL before returning.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
[small fix to use wlvif->ps_compl instead of wl->ps_compl]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use the newly introduced ieee80211_free_txskb() instead
of dev_kfree_skb() for failed tx packets.
Additionally, if the skb is a dummy packet, re-enqueue
it (as the fw expects it) instead of freeing it.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We need to set the extended radio parameters for wl127x only.
Currently, we were only calling this command with wl127x STA mode, but
we should also do it for AP mode.
Move the call to the extended radio paramaters to the common hw_init
and use a single if for the chip type to do everything at once.
Signed-off-by: Luciano Coelho <coelho@ti.com>
We should not get an hlid value bigger than WL12XX_MAX_LINKS from
wl1271_rx_handle_data(). We have a WARN_ON in case it happens. But
despite the warning, we would still go ahead and write the hlid bit
into active_hlids (a stack variable). This would cause us to
overwrite other data in the stack.
To avoid this problem, we now skip the write when issuing the warning,
so at least we don't corrupt data.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Commit 80900d0140 accidently broke
the ABI for testmode commands. Restore the ABI again.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Luciano Coelho <coelho@ti.com>
CC [M] drivers/net/wireless/wl12xx/tx.o
drivers/net/wireless/wl12xx/tx.c: In function ‘wl1271_tx_fill_hdr’:
drivers/net/wireless/wl12xx/tx.c:288:6: warning: ‘tx_attr’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The user can pass broadcast SSID (ssid="") in the list of SSIDs for active scan.
In this case the loop was attempting to match SSIDs in the filter
list to this empty entry and marking them as HIDDEN (sending probe
request) by mistake
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
During plt init we configure some redundant commands,
which are not needed for plt (specifically, we shouldn't
configure any role-specific params, as there are no
active roles). remove them.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
fix several issues in testmode test/interrogate commands:
1. check the driver state is not OFF.
2. wakeup the chip from elp (if needed)
3. fix memory leak in wl1271_tm_cmd_interrogate()
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
After the ibss carrier issue was fixed, we can revert
the following patch:
commit 48309fd477
Author: Shahar Lev <shahar@wizery.com>
Date: Fri Oct 7 18:17:25 2011 +0200
wl12xx: remove warning message during IBSS Tx
mac80211 sets the carrier on an IBSS interface even when no network is
joined. Ignore garbage frames transmitted on a disconnected IBSS
interface without printing warnings.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use an appropriate mac80211 flags in CCMP keys to indicate we are
calculating the CCMP IV in HW, but require room for the IV to be reserved
in the skb. The space is reserved by mac80211.
depends on "mac80211: support adding IV-room in the skb for CCMP keys".
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Print the name of nvs/fw if request_firmware fails. This will make
troubleshooting a bit easier.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
During reconfig we can get the BSS_CHANGED_AP_PROBE_RESP indication
even if a probe-resp has not been set in the first place. Therefore
ignore the error when not getting a probe-resp from mac80211. Resort to
the legacy probe-resp in this case.
Also take this opportunity to add a vif argument to the set_probe_resp
function.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The keep alive template should have a max size of
sizeof(struct ieee80211_qos_hdr).
Additionally, Remove the redundant wl12xx_qos_null_data_template
struct.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl12xx driver supports probe-response offloading, and the WPS, WPS2
and P2P special cases as well.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When operating in AP-mode, replace our probe-response template when a
notification is recieved from mac80211. We preserve the "legacy" way of
configuring a probe-response according to beacon for IBSS mode and for
versions of hostapd that do not support this feature.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
An nvs with malformed contents could cause the processing of the
calibration data to read beyond the end of the buffer. Prevent this
from happening by adding bound checking.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Cc: stable@kernel.org
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Check for out of bound FEM index to prevent reading beyond ini
memory end.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Cc: stable@kernel.org
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Dan Williams <dcbw@redhat.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Luciano Coelho <coelho@ti.com>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A minor fix for the check that verifies that all given SSIDs (in req) exist
in the filters (the match sets)
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1271_suspend/resume() accessed the wrong struct and not wl1271
which caused it to think that wow was enabled when it wasn't.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Idle changes are currently handled per hardware.
However, some operations should be done only per-interface.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If the skb contains the NO_CCK flag, use the p2p rate index
(which contains only the OFDM rates)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Set the TX rate of probe requests during scanning according to the
no_cck flag in the scan request struct.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The chunk size used during firmware upload was set to 512, which is
the size of a single SDIO block (or two). This is very inneficient
because we send one or two blocks only per SDIO transaction and don't
get the full benefits of sdio block transfers.
This patch increases the chunk size to 16K. This more than doubles
the transfer speed both in wl127x and wl128x chips, with greater
impact on the latter:
wl127x: 512 bytes chunk -> ~132ms
16384 bytes chunk -> ~57ms
wl128x: 512 bytes chunk -> ~216ms
16384 bytes chunk -> ~37ms
Signed-off-by: Luciano Coelho <coelho@ti.com>
The sdio driver uses a block size of 512 bytes by default. With our
card, this doesn't work correctly because it sets the block size FBR
in the chip too early (ie. before the chip is powered on). Thus, if
we don't set it explicitly, block mode remains disabled in the chip.
If we try to send more data than fits in one block, the sdio driver
will split it into separate blocks before sending to the chip. This
causes problems because the chip is not expecting multiple blocks.
At the moment this is not a problem, because we use chunks of 512
bytes for firmware upload and the data is always sent in byte mode.
In the next patch, we will change the chunk size to a bigger value, so
this patch is a preparation for that.
Signed-off-by: Luciano Coelho <coelho@ti.com>
SDIO blocksize alignment support is now the rule, not the exception.
To simplify the code in patches to come, invert the meaning of the
quirk to be negative (ie. the quirk is set if the device does _not_
support blocksize alignment).
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl->vif should be cleared on remove_interface()
(rather than on stop()) even when only a single
vif is supported, because during vif mode change
stop() might not get called (e.g. because of
monitor interface existence)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add debugfs key to dump information regarding the
active vifs (similar to the driver_state debugfs key)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Enable beacon filtering on STA init, and don't disable it when entering
active mode. Otherwise dynamic-PS supports means we receive beacons from
the current AP during any Tx/Rx performed by the driver.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The rate policies are configured only after association,
resulting in auth req being sent in wrong rates.
Reconfigure rate policies on bitrate mask change.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Device role is always started along with ROC.
Couple them together by introducing new wl12xx_start_dev
and wl12xx_stop_dev functions.
By using these functions, we solve a bug that occured during
channel switch - we started the dev role on one channel, and
ROCed on a different one.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
These were getting the macros from an implicit module.h
include via device.h, but we are planning to clean that up.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
drivers/net: Add export.h to wireless/brcm80211/brcmfmac/bcmsdh.c
This relatively recently added file uses EXPORT_SYMBOL and hence
needs export.h included so that it is compatible with the module.h
split up work.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Injected packets are sent with no vif, causing the wl12xx
to NULL-dereference in multiple places.
Furthermore, injected packets are currently not sent at all,
as system_hlid doesn't belong to any specific role, so
wl1271_skb_dequeue() never return its packets.
Handle both these problems.
Reported-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
