driver (Christophe Jaillet)
- Fix control buffer enablement regression on Meditek MT7896 (Frank
Wunderlich)
- Drop spaces before TABs in different places: thermal-of, ST drivers
and Makefile (Geert Uytterhoeven)
- Adjust DT binding for NXP as fsl,tmu-range min/maxItems can vary
among several SoC versions (Fabio Estevam)
- Add support for H616 THS controller for the Sun8i platforms. Note
that this change relies on another change in the SoC specific code
which is included in this branch (Martin Botka)
- Don't fail probe due to zone registration failure because there is
no trip points defined in the DT (Mark Brown)
- Support variable TMU array size for new platforms (Peng Fan)
- Adjust the DT binding for thermal-of and make the polling time not
required and assume it is zero when not found in the DT (Konrad
Dybcio)
- Add r8a779h0 support in both the DT and the driver (Geert Uytterhoeven)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAmXxqsUACgkQqDIjiipP
6E9jDgf+NpBl2l9Wb8EhFcB+QRcOY79rn8KzifM4XdU1qwoog3I64lt5mAcznpbf
7hLK9DQJYjuIx8oi/uxKaYSCno1bwuY/Vpi0/BBQ2DxhhX26C7XfZ+D4o1M3/ciZ
/jsoaXg3WMKYVeywaHohWxjWH+rLGXxmxDlfcAXlKdAZkbEKLCzsbaRaSy/H8Xhc
zk9Cr2RdV+HHcuAWK1TGEHUGXINSR5tk5TvY7QCfvLYsloGpSLi6vr68CAEpvBQB
6pxW8BkAWAVQy6pgP3WthzpE+ZkEnv1vhu7fn0uoEjuxedqvdj+PKDC4svm1k/pA
+8sV89A5RZi1zOoWWYj8TnH/K2W85w==
=rTh4
-----END PGP SIGNATURE-----
Merge tag 'thermal-v6.9-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Merge additional thermal control changes for 6.9-rc1 from Daniel Lezcano:
"- Fix memory leak in the error path at probe time in the Mediatek LVTS
driver (Christophe Jaillet)
- Fix control buffer enablement regression on Meditek MT7896 (Frank
Wunderlich)
- Drop spaces before TABs in different places: thermal-of, ST drivers
and Makefile (Geert Uytterhoeven)
- Adjust DT binding for NXP as fsl,tmu-range min/maxItems can vary
among several SoC versions (Fabio Estevam)
- Add support for H616 THS controller for the Sun8i platforms. Note
that this change relies on another change in the SoC specific code
which is included in this branch (Martin Botka)
- Don't fail probe due to zone registration failure because there is
no trip points defined in the DT (Mark Brown)
- Support variable TMU array size for new platforms (Peng Fan)
- Adjust the DT binding for thermal-of and make the polling time not
required and assume it is zero when not found in the DT (Konrad
Dybcio)
- Add r8a779h0 support in both the DT and the driver (Geert Uytterhoeven)"
* tag 'thermal-v6.9-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
thermal/drivers/rcar_gen3: Add support for R-Car V4M
dt-bindings: thermal: rcar-gen3-thermal: Add r8a779h0 support
thermal/of: Assume polling-delay(-passive) 0 when absent
dt-bindings: thermal-zones: Don't require polling-delay(-passive)
thermal/drivers/qoriq: Fix getting tmu range
thermal/drivers/sun8i: Don't fail probe due to zone registration failure
thermal/drivers/sun8i: Add support for H616 THS controller
thermal/drivers/sun8i: Add SRAM register access code
thermal/drivers/sun8i: Extend H6 calibration to support 4 sensors
thermal/drivers/sun8i: Explain unknown H6 register value
dt-bindings: thermal: sun8i: Add H616 THS controller
soc: sunxi: sram: export register 0 for THS on H616
dt-bindings: thermal: qoriq-thermal: Adjust fsl,tmu-range min/maxItems
thermal: Drop spaces before TABs
thermal/drivers/mediatek: Fix control buffer enablement on MT7896
thermal/drivers/mediatek/lvts_thermal: Fix a memory leak in an error handling path
- Store zone trips table and zone operations directly in struct
thermal_zone_device (Rafael Wysocki).
- Fix up flex array initialization during thermal zone device
registration (Nathan Chancellor).
- Rework writable trip points handling in the thermal core and
several drivers (Rafael Wysocki).
- Thermal core code cleanups (Dan Carpenter, Flavio Suligoi).
- Use thermal zone accessor functions in the int340x Intel thermal
driver (Rafael Wysocki).
- Add Lunar Lake-M PCI ID to the int340x Intel thermal driver (Srinivas
Pandruvada).
- Minor fixes for thermal governors (Rafael Wysocki, Di Shen).
- Trip point handling fixes for the iwlwifi wireless driver (Rafael
Wysocki).
- Code cleanups (Rafael J. Wysocki, AngeloGioacchino Del Regno).
-----BEGIN PGP SIGNATURE-----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=Is/Y
-----END PGP SIGNATURE-----
Merge tag 'thermal-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"These mostly change the thermal core in a few ways allowing thermal
drivers to be simplified, in particular in their removal and failing
probe handling parts that are notoriously prone to errors, and
propagate the changes to several drivers.
Apart from that, support for a new platform is added (Intel Lunar
Lake-M), some bugs are fixed and some code is cleaned up, as usual.
Specifics:
- Store zone trips table and zone operations directly in struct
thermal_zone_device (Rafael Wysocki)
- Fix up flex array initialization during thermal zone device
registration (Nathan Chancellor)
- Rework writable trip points handling in the thermal core and
several drivers (Rafael Wysocki)
- Thermal core code cleanups (Dan Carpenter, Flavio Suligoi)
- Use thermal zone accessor functions in the int340x Intel thermal
driver (Rafael Wysocki)
- Add Lunar Lake-M PCI ID to the int340x Intel thermal driver
(Srinivas Pandruvada)
- Minor fixes for thermal governors (Rafael Wysocki, Di Shen)
- Trip point handling fixes for the iwlwifi wireless driver (Rafael
Wysocki)
- Code cleanups (Rafael J. Wysocki, AngeloGioacchino Del Regno)"
* tag 'thermal-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (29 commits)
thermal: core: remove unnecessary check in trip_point_hyst_store()
thermal: intel: int340x_thermal: Use thermal zone accessor functions
thermal: core: Remove excess empty line from a comment
thermal: int340x: processor_thermal: Add Lunar Lake-M PCI ID
thermal: core: Eliminate writable trip points masks
thermal: of: Set THERMAL_TRIP_FLAG_RW_TEMP directly
thermal: imx: Set THERMAL_TRIP_FLAG_RW_TEMP directly
wifi: iwlwifi: mvm: Set THERMAL_TRIP_FLAG_RW_TEMP directly
mlxsw: core_thermal: Set THERMAL_TRIP_FLAG_RW_TEMP directly
thermal: intel: Set THERMAL_TRIP_FLAG_RW_TEMP directly
thermal: core: Drop the .set_trip_hyst() thermal zone operation
thermal: core: Add flags to struct thermal_trip
thermal: core: Move initial num_trips assignment before memcpy()
thermal: Get rid of CONFIG_THERMAL_WRITABLE_TRIPS
thermal: intel: Adjust ops handling during thermal zone registration
thermal: ACPI: Constify acpi_thermal_zone_ops
thermal: core: Store zone ops in struct thermal_zone_device
thermal: intel: Discard trip tables after zone registration
thermal: ACPI: Discard trips table after zone registration
thermal: core: Store zone trips table in struct thermal_zone_device
...
- Allow the Energy Model to be updated dynamically (Lukasz Luba).
- Add support for LZ4 compression algorithm to the hibernation image
creation and loading code (Nikhil V).
- Fix and clean up system suspend statistics collection (Rafael
Wysocki).
- Simplify device suspend and resume handling in the power management
core code (Rafael Wysocki).
- Fix PCI hibernation support description (Yiwei Lin).
- Make hibernation take set_memory_ro() return values into account as
appropriate (Christophe Leroy).
- Set mem_sleep_current during kernel command line setup to avoid an
ordering issue with handling it (Maulik Shah).
- Fix wake IRQs handling when pm_runtime_force_suspend() is used as a
driver's system suspend callback (Qingliang Li).
- Simplify pm_runtime_get_if_active() usage and add a replacement for
pm_runtime_put_autosuspend() (Sakari Ailus).
- Add a tracepoint for runtime_status changes tracking (Vilas Bhat).
- Fix section title markdown in the runtime PM documentation (Yiwei
Lin).
- Enable preferred core support in the amd-pstate cpufreq driver (Meng
Li).
- Fix min_perf assignment in amd_pstate_adjust_perf() and make the
min/max limit perf values in amd-pstate always stay within the
(highest perf, lowest perf) range (Tor Vic, Meng Li).
- Allow intel_pstate to assign model-specific values to strings used in
the EPP sysfs interface and make it do so on Meteor Lake (Srinivas
Pandruvada).
- Drop long-unused cpudata::prev_cummulative_iowait from the
intel_pstate cpufreq driver (Jiri Slaby).
- Prevent scaling_cur_freq from exceeding scaling_max_freq when the
latter is an inefficient frequency (Shivnandan Kumar).
- Change default transition delay in cpufreq to 2ms (Qais Yousef).
- Remove references to 10ms minimum sampling rate from comments in the
cpufreq code (Pierre Gondois).
- Honour transition_latency over transition_delay_us in cpufreq (Qais
Yousef).
- Stop unregistering cpufreq cooling on CPU hot-remove (Viresh Kumar).
- General enhancements / cleanups to ARM cpufreq drivers (tianyu2,
Nícolas F. R. A. Prado, Erick Archer, Arnd Bergmann, Anastasia
Belova).
- Update cpufreq-dt-platdev to block/approve devices (Richard Acayan).
- Make the SCMI cpufreq driver get a transition delay value from
firmware (Pierre Gondois).
- Prevent the haltpoll cpuidle governor from shrinking guest
poll_limit_ns below grow_start (Parshuram Sangle).
- Avoid potential overflow in integer multiplication when computing
cpuidle state parameters (C Cheng).
- Adjust MWAIT hint target C-state computation in the ACPI cpuidle
driver and in intel_idle to return a correct value for C0 (He
Rongguang).
- Address multiple issues in the TPMI RAPL driver and add support for
new platforms (Lunar Lake-M, Arrow Lake) to Intel RAPL (Zhang Rui).
- Fix freq_qos_add_request() return value check in dtpm_cpu (Daniel
Lezcano).
- Fix kernel-doc for dtpm_create_hierarchy() (Yang Li).
- Fix file leak in get_pkg_num() in x86_energy_perf_policy (Samasth
Norway Ananda).
- Fix cpupower-frequency-info.1 man page typo (Jan Kratochvil).
- Fix a couple of warnings in the OPP core code related to W=1
builds (Viresh Kumar).
- Move dev_pm_opp_{init|free}_cpufreq_table() to pm_opp.h (Viresh
Kumar).
- Extend dev_pm_opp_data with turbo support (Sibi Sankar).
- dt-bindings: drop maxItems from inner items (David Heidelberg).
-----BEGIN PGP SIGNATURE-----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=UePT
-----END PGP SIGNATURE-----
Merge tag 'pm-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"From the functional perspective, the most significant change here is
the addition of support for Energy Models that can be updated
dynamically at run time.
There is also the addition of LZ4 compression support for hibernation,
the new preferred core support in amd-pstate, new platforms support in
the Intel RAPL driver, new model-specific EPP handling in intel_pstate
and more.
Apart from that, the cpufreq default transition delay is reduced from
10 ms to 2 ms (along with some related adjustments), the system
suspend statistics code undergoes a significant rework and there is a
usual bunch of fixes and code cleanups all over.
Specifics:
- Allow the Energy Model to be updated dynamically (Lukasz Luba)
- Add support for LZ4 compression algorithm to the hibernation image
creation and loading code (Nikhil V)
- Fix and clean up system suspend statistics collection (Rafael
Wysocki)
- Simplify device suspend and resume handling in the power management
core code (Rafael Wysocki)
- Fix PCI hibernation support description (Yiwei Lin)
- Make hibernation take set_memory_ro() return values into account as
appropriate (Christophe Leroy)
- Set mem_sleep_current during kernel command line setup to avoid an
ordering issue with handling it (Maulik Shah)
- Fix wake IRQs handling when pm_runtime_force_suspend() is used as a
driver's system suspend callback (Qingliang Li)
- Simplify pm_runtime_get_if_active() usage and add a replacement for
pm_runtime_put_autosuspend() (Sakari Ailus)
- Add a tracepoint for runtime_status changes tracking (Vilas Bhat)
- Fix section title markdown in the runtime PM documentation (Yiwei
Lin)
- Enable preferred core support in the amd-pstate cpufreq driver
(Meng Li)
- Fix min_perf assignment in amd_pstate_adjust_perf() and make the
min/max limit perf values in amd-pstate always stay within the
(highest perf, lowest perf) range (Tor Vic, Meng Li)
- Allow intel_pstate to assign model-specific values to strings used
in the EPP sysfs interface and make it do so on Meteor Lake
(Srinivas Pandruvada)
- Drop long-unused cpudata::prev_cummulative_iowait from the
intel_pstate cpufreq driver (Jiri Slaby)
- Prevent scaling_cur_freq from exceeding scaling_max_freq when the
latter is an inefficient frequency (Shivnandan Kumar)
- Change default transition delay in cpufreq to 2ms (Qais Yousef)
- Remove references to 10ms minimum sampling rate from comments in
the cpufreq code (Pierre Gondois)
- Honour transition_latency over transition_delay_us in cpufreq (Qais
Yousef)
- Stop unregistering cpufreq cooling on CPU hot-remove (Viresh Kumar)
- General enhancements / cleanups to ARM cpufreq drivers (tianyu2,
Nícolas F. R. A. Prado, Erick Archer, Arnd Bergmann, Anastasia
Belova)
- Update cpufreq-dt-platdev to block/approve devices (Richard Acayan)
- Make the SCMI cpufreq driver get a transition delay value from
firmware (Pierre Gondois)
- Prevent the haltpoll cpuidle governor from shrinking guest
poll_limit_ns below grow_start (Parshuram Sangle)
- Avoid potential overflow in integer multiplication when computing
cpuidle state parameters (C Cheng)
- Adjust MWAIT hint target C-state computation in the ACPI cpuidle
driver and in intel_idle to return a correct value for C0 (He
Rongguang)
- Address multiple issues in the TPMI RAPL driver and add support for
new platforms (Lunar Lake-M, Arrow Lake) to Intel RAPL (Zhang Rui)
- Fix freq_qos_add_request() return value check in dtpm_cpu (Daniel
Lezcano)
- Fix kernel-doc for dtpm_create_hierarchy() (Yang Li)
- Fix file leak in get_pkg_num() in x86_energy_perf_policy (Samasth
Norway Ananda)
- Fix cpupower-frequency-info.1 man page typo (Jan Kratochvil)
- Fix a couple of warnings in the OPP core code related to W=1 builds
(Viresh Kumar)
- Move dev_pm_opp_{init|free}_cpufreq_table() to pm_opp.h (Viresh
Kumar)
- Extend dev_pm_opp_data with turbo support (Sibi Sankar)
- dt-bindings: drop maxItems from inner items (David Heidelberg)"
* tag 'pm-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (95 commits)
dt-bindings: opp: drop maxItems from inner items
OPP: debugfs: Fix warning around icc_get_name()
OPP: debugfs: Fix warning with W=1 builds
cpufreq: Move dev_pm_opp_{init|free}_cpufreq_table() to pm_opp.h
OPP: Extend dev_pm_opp_data with turbo support
Fix cpupower-frequency-info.1 man page typo
cpufreq: scmi: Set transition_delay_us
firmware: arm_scmi: Populate fast channel rate_limit
firmware: arm_scmi: Populate perf commands rate_limit
cpuidle: ACPI/intel: fix MWAIT hint target C-state computation
PM: sleep: wakeirq: fix wake irq warning in system suspend
powercap: dtpm: Fix kernel-doc for dtpm_create_hierarchy() function
cpufreq: Don't unregister cpufreq cooling on CPU hotplug
PM: suspend: Set mem_sleep_current during kernel command line setup
cpufreq: Honour transition_latency over transition_delay_us
cpufreq: Limit resolving a frequency to policy min/max
Documentation: PM: Fix runtime_pm.rst markdown syntax
cpufreq: amd-pstate: adjust min/max limit perf
cpufreq: Remove references to 10ms min sampling rate
cpufreq: intel_pstate: Update default EPPs for Meteor Lake
...
Add support for the Thermal Sensor/Chip Internal Voltage Monitor/Core
Voltage Monitor (THS/CIVM/CVM) on the Renesas R-Car V4M (R8A779H0) SoC.
The conversion formulas for R-Car V4M are the same as for other R-Car
Gen4 SoCs.
Based on a patch in the BSP by Duy Nguyen.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/bd5b002a802c1e058e0048592f17862db1d04263.1709722342.git.geert+renesas@glider.be
Currently, thermal zones associated with providers that have interrupts
for signaling hot/critical trips are required to set a polling-delay
of 0 to indicate no polling. This feels a bit backwards.
Change the code such that "no polling delay" also means "no polling".
Suggested-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240125-topic-thermal-v1-2-3c9d4dced138@linaro.org
TMU Version 1 has 4 TTRCRs, while TMU Version >=2 has 16 TTRCRs.
So limit the len to 4 will report "invalid range data" for i.MX93.
This patch drop the local array with allocated ttrcr array and
able to support larger tmu ranges.
Fixes: f12d60c81f ("thermal/drivers/qoriq: Support version 2.1")
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240226003657.3012880-1-peng.fan@oss.nxp.com
Currently the sun8i thermal driver will fail to probe if any of the
thermal zones it is registering fails to register with the thermal core.
Since we currently do not define any trip points for the GPU thermal
zones on at least A64 or H5 this means that we have no thermal support
on these platforms:
[ 1.698703] thermal_sys: Failed to find 'trips' node
[ 1.698707] thermal_sys: Failed to find trip points for thermal-sensor id=1
even though the main CPU thermal zone on both SoCs is fully configured.
This does not seem ideal, while we may not be able to use all the zones
it seems better to have those zones which are usable be operational.
Instead just carry on registering zones if we get any non-deferral
error, allowing use of those zones which are usable.
This means that we also need to update the interrupt handler to not
attempt to notify the core for events on zones which we have not
registered, I didn't see an ability to mask individual interrupts and
I would expect that interrupts would still be indicated in the ISR even
if they were masked.
Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240123-thermal-sun8i-registration-v3-1-3e5771b1bbdd@kernel.org
Add support for the thermal sensor found in H616 SoCs, is the same as
the H6 thermal sensor controller, but with four sensors.
Also the registers readings are wrong, unless a bit in the first SYS_CFG
register cleared, so set exercise the SRAM regmap to take care of that.
Signed-off-by: Martin Botka <martin.botka@somainline.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240219153639.179814-7-andre.przywara@arm.com
The Allwinner H616 SoC needs to clear a bit in one register in the SRAM
controller, to report reasonable temperature values. On reset, bit 16 in
register 0x3000000 is set, which leads to the driver reporting
temperatures around 200C. Clearing this bit brings the values down to the
expected range. The BSP code does a one-time write in U-Boot, with a
comment just mentioning the effect on the THS, but offering no further
explanation.
To not rely on firmware to set things up for us, add code that queries
the SRAM controller device via a DT phandle link, then clear just this
single bit.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240219153639.179814-6-andre.przywara@arm.com
The H616 SoC resembles the H6 thermal sensor controller, with a few
changes like four sensors.
Extend sun50i_h6_ths_calibrate() function to support calibration of
these sensors.
Co-developed-by: Martin Botka <martin.botka@somainline.org>
Signed-off-by: Martin Botka <martin.botka@somainline.org>
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240219153639.179814-5-andre.przywara@arm.com
So far we were ORing in some "unknown" value into the THS control
register on the Allwinner H6. This part of the register is not explained
in the H6 manual, but the H616 manual details those bits, and on closer
inspection the THS IP blocks in both SoCs seem very close:
- The BSP code for both SoCs writes the same values into THS_CTRL.
- The reset values of at least the first three registers are the same.
Replace the "unknown" value with its proper meaning: "acquire time",
most probably the sample part of the sample & hold circuit of the ADC,
according to its explanation in the H616 manual.
No functional change, just a macro rename and adjustment.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240219153639.179814-4-andre.przywara@arm.com
Reading thermal sensor on mt7986 devices returns invalid temperature:
bpi-r3 ~ # cat /sys/class/thermal/thermal_zone0/temp
-274000
Fix this by adding missing members in mtk_thermal_data struct which were
used in mtk_thermal_turn_on_buffer after commit 33140e668b.
Cc: stable@vger.kernel.org
Fixes: 33140e668b ("thermal/drivers/mediatek: Control buffer enablement tweaks")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230907112018.52811-1-linux@fw-web.de
If devm_krealloc() fails, then 'efuse' is leaking.
So free it to avoid a leak.
Fixes: f5f633b182 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/481d345233862d58c3c305855a93d0dbc2bbae7e.1706431063.git.christophe.jaillet@wanadoo.fr
Merge Enery Model changes for 6.9-rc1:
- Allow the Energy Model to be updated dynamically (Lukasz Luba).
* pm-em: (24 commits)
PM: EM: Fix nr_states warnings in static checks
Documentation: EM: Update with runtime modification design
PM: EM: Add em_dev_compute_costs()
PM: EM: Remove old table
PM: EM: Change debugfs configuration to use runtime EM table data
drivers/thermal/devfreq_cooling: Use new Energy Model interface
drivers/thermal/cpufreq_cooling: Use new Energy Model interface
powercap/dtpm_devfreq: Use new Energy Model interface to get table
powercap/dtpm_cpu: Use new Energy Model interface to get table
PM: EM: Optimize em_cpu_energy() and remove division
PM: EM: Support late CPUs booting and capacity adjustment
PM: EM: Add performance field to struct em_perf_state and optimize
PM: EM: Add em_perf_state_from_pd() to get performance states table
PM: EM: Introduce em_dev_update_perf_domain() for EM updates
PM: EM: Add functions for memory allocations for new EM tables
PM: EM: Use runtime modified EM for CPUs energy estimation in EAS
PM: EM: Introduce runtime modifiable table
PM: EM: Split the allocation and initialization of the EM table
PM: EM: Check if the get_cost() callback is present in em_compute_costs()
PM: EM: Introduce em_compute_costs()
...
Merge thermal core changes and Intel thermal drivers changes for
6.9-rc1:
- Store zone trips table and zone operations directly in struct
thermal_zone_device (Rafael Wysocki).
- Rework writable trip points handling (Rafael Wysocki).
- Thermal core code cleanups (Dan Carpenter, Flavio Suligoi).
- Use thermal zone accessor functions in the int340x Intel thermal
driver (Rafael Wysocki).
- Add Lunar Lake-M PCI ID to the int340x Intel thermal driver (Srinivas
Pandruvada).
* thermal-core:
thermal: core: remove unnecessary check in trip_point_hyst_store()
thermal: core: Remove excess empty line from a comment
thermal: core: Eliminate writable trip points masks
thermal: of: Set THERMAL_TRIP_FLAG_RW_TEMP directly
thermal: imx: Set THERMAL_TRIP_FLAG_RW_TEMP directly
wifi: iwlwifi: mvm: Set THERMAL_TRIP_FLAG_RW_TEMP directly
mlxsw: core_thermal: Set THERMAL_TRIP_FLAG_RW_TEMP directly
thermal: intel: Set THERMAL_TRIP_FLAG_RW_TEMP directly
thermal: core: Drop the .set_trip_hyst() thermal zone operation
thermal: core: Add flags to struct thermal_trip
thermal: core: Move initial num_trips assignment before memcpy()
thermal: Get rid of CONFIG_THERMAL_WRITABLE_TRIPS
thermal: intel: Adjust ops handling during thermal zone registration
thermal: ACPI: Constify acpi_thermal_zone_ops
thermal: core: Store zone ops in struct thermal_zone_device
thermal: intel: Discard trip tables after zone registration
thermal: ACPI: Discard trips table after zone registration
thermal: core: Store zone trips table in struct thermal_zone_device
* thermal-intel:
thermal: intel: int340x_thermal: Use thermal zone accessor functions
thermal: int340x: processor_thermal: Add Lunar Lake-M PCI ID
This code was shuffled around a bit recently. We no longer need to
check the value of "ret" because we know it's zero.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make int340x_thermal use the dedicated accessor functions for the
thermal zone device object address and the thermal zone type string.
This is requisite for future thermal core improvements.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
The first and the third lines of the kerneldoc comment for:
thermal_zone_device_set_polling()
belong to the same sentences, so join them together.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add Lunar Lake-M PCI ID for processor thermal device.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
All of the thermal_zone_device_register_with_trips() callers pass zero
writable trip points masks to it, so drop the mask argument from that
function and update all of its callers accordingly.
This also removes the artificial trip points per zone limit of 32,
related to using writable trip points masks.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
It is now possible to flag trip points with THERMAL_TRIP_FLAG_RW_TEMP
to allow their temperature to be set from user space via sysfs instead
of using a nonzero writable trips mask during thermal zone registration,
so make the OF thermal code do that.
No intentional functional impact.
Note that this change is requisite for dropping the mask argument from
thermal_zone_device_register_with_trips() going forward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
It is now possible to flag trip points with THERMAL_TRIP_FLAG_RW_TEMP
to allow their temperature to be set from user space via sysfs instead
of using a nonzero writable trips mask during thermal zone registration,
so make the imx thermal code do that.
No intentional functional impact.
Note that this change is requisite for dropping the mask argument from
thermal_zone_device_register_with_trips() going forward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Some Intel thermal drivers need/want the temperature of their trip
points to be set by user space via sysfs and so they pass nonzero
writable trip masks during thermal zone registration for this purpose.
It is now possible to achieve the same result by setting the
THERMAL_TRIP_FLAG_RW_TEMP trip flag directly, so modify the drivers
in question to do that instead of using a nonzero writable trips mask.
No intentional functional impact.
Note that this change is requisite for dropping the mask argument from
thermal_zone_device_register_with_trips() going forward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
None of the users of the thermal core provides a .set_trip_hyst()
thermal zone operation, so drop that callback from struct
thermal_zone_device_ops and update trip_point_hyst_store()
accordingly.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In order to allow thermal zone creators to specify the writability of
trip point temperature and hysteresis on a per-trip basis, add a flags
field to struct thermal_trip and define flags to represent the desired
trip properties.
Also make thermal_zone_device_register_with_trips() set the
THERMAL_TRIP_FLAG_RW_TEMP flag for all trips covered by the writable
trips mask passed to it and modify the thermal sysfs code to look at
the trip flags instead of using the writable trips mask directly or
checking the presence of the .set_trip_hyst() zone callback.
Additionally, make trip_point_temp_store() and trip_point_hyst_store()
fail with an error code if the trip passed to one of them has
THERMAL_TRIP_FLAG_RW_TEMP or THERMAL_TRIP_FLAG_RW_HYST,
respectively, clear in its flags.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When booting a CONFIG_FORTIFY_SOURCE=y kernel compiled with a toolchain
that supports __counted_by() (such as clang-18 and newer), there is a
panic on boot:
[ 2.913770] memcpy: detected buffer overflow: 72 byte write of buffer size 0
[ 2.920834] WARNING: CPU: 2 PID: 1 at lib/string_helpers.c:1027 __fortify_report+0x5c/0x74
...
[ 3.039208] Call trace:
[ 3.041643] __fortify_report+0x5c/0x74
[ 3.045469] __fortify_panic+0x18/0x20
[ 3.049209] thermal_zone_device_register_with_trips+0x4c8/0x4f8
This panic occurs because trips is counted by num_trips but num_trips is
assigned after the call to memcpy(), so the fortify checks think the
buffer size is zero because tz was allocated with kzalloc().
Move the num_trips assignment before the memcpy() to resolve the panic
and ensure that the fortify checks work properly.
Fixes: 9b0a627586 ("thermal: core: Store zone trips table in struct thermal_zone_device")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The only difference made by CONFIG_THERMAL_WRITABLE_TRIPS is whether or
not the writable trips mask passed during thermal zone registration
will take any effect, but whoever passes a non-zero writable trips mask
to thermal_zone_device_register_with_trips() can be forgiven thinking
that it will always work.
Moreover, some thermal drivers expect user space to set trip temperature
values, so they select CONFIG_THERMAL_WRITABLE_TRIPS, possibly overriding
a manual choice to unset it and going against the design purportedly
allowing system integrators to decide on the writability of trip points
for the given kernel build. It is also set in one platform's defconfig.
Forthermore, CONFIG_THERMAL_WRITABLE_TRIPS only affects trip temperature,
because trip hysteresis is writable as long as the thermal zone provides
a callback to update it, regardless of the CONFIG_THERMAL_WRITABLE_TRIPS
value.
The above means that the symbol in question is used inconsistently and
its purpose is at least moot, so remove it and always take the writable
trip mask passed to thermal_zone_device_register_with_trips() into
account.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Because thermal zone operations are now stored directly in struct
thermal_zone_device, thermal zone creators can discard the operations
structure after the zone registration is complete, or it can be made
read-only.
Accordingly, make int340x_thermal_zone_add() use a local variable to
represent thermal zone operations, so it is freed automatically upon the
function exit, and make the other Intel thermal drivers use const zone
operations structures.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The current code requires thermal zone creators to pass pointers to
writable ops structures to thermal_zone_device_register_with_trips()
which needs to modify the target struct thermal_zone_device_ops object
if the "critical" operation in it is NULL.
Moreover, the callers of thermal_zone_device_register_with_trips() are
required to hold on to the struct thermal_zone_device_ops object passed
to it until the given thermal zone is unregistered.
Both of these requirements are quite inconvenient, so modify struct
thermal_zone_device to contain struct thermal_zone_device_ops as field and
make thermal_zone_device_register_with_trips() copy the contents of the
struct thermal_zone_device_ops passed to it via a pointer (which can be
const now) to that field.
Also adjust the code using thermal zone ops accordingly and modify
thermal_of_zone_register() to use a local ops variable during
thermal zone registration so ops do not need to be freed in
thermal_of_zone_unregister() any more.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Because the thermal core creates and uses its own copy of the trips
table passed to thermal_zone_device_register_with_trips(), it is not
necessary to hold on to a local copy of it any more after the given
thermal zone has been registered.
Accordingly, modify Intel thermal drivers to discard the trips tables
passed to thermal_zone_device_register_with_trips() after thermal zone
registration, for example by storing them in local variables which are
automatically discarded when the zone registration is complete.
Also make some additional code simplifications unlocked by the above
changes.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The current code expects thermal zone creators to pass a pointer to a
writable trips table to thermal_zone_device_register_with_trips() and
that trips table is then used by the thermal core going forward.
Consequently, the callers of thermal_zone_device_register_with_trips()
are required to hold on to the trips table passed to it until the given
thermal zone is unregistered, at which point the trips table can be
freed, but at the same time they are not expected to access that table
directly. This is both error prone and confusing.
To address it, turn the trips table pointer in struct thermal_zone_device
into a flex array (counted by its num_trips field), allocate it during
thermal zone device allocation and copy the contents of the trips table
supplied by the zone creator (which can be const now) into it, which
will allow the callers of thermal_zone_device_register_with_trips() to
drop their trip tables right after the zone registration.
This requires the imx thermal driver to be adjusted to store the new
temperature in its internal trips table in imx_set_trip_temp(), because
it will be separate from the core's trips table now and it has to be
explicitly kept in sync with the latter.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Merge thermal core changes for 6.9:
- Minor fixes for thermal governors (Rafael J. Wysocki, Di Shen).
- Trip point handling fixes for the iwlwifi wireless driver (Rafael J.
Wysocki).
- Code cleanups (Rafael J. Wysocki, AngeloGioacchino Del Regno).
* thermal-tmp:
thermal: gov_power_allocator: Avoid overwriting PID coefficients from setup time
thermal: sysfs: Fix up white space in trip_point_temp_store()
iwlwifi: mvm: Use for_each_thermal_trip() for walking trip points
iwlwifi: mvm: Populate trip table before registering thermal zone
iwlwifi: mvm: Drop unused fw_trips_index[] from iwl_mvm_thermal_device
thermal: core: Change governor name to const char pointer
thermal: gov_bang_bang: Fix possible cooling device state ping-pong
thermal: gov_fair_share: Fix dependency on trip points ordering
The RAPL framework uses CPU hotplug locking to protect the rapl_packages
list and rp->lead_cpu to guarantee that
1. the RAPL package device is not unprobed and freed
2. the cached rp->lead_cpu is always valid
for operations like powercap sysfs accesses.
Current RAPL APIs assume being called from CPU hotplug callbacks which
hold the CPU hotplug lock, but TPMI RAPL driver invokes the APIs in the
driver's .probe() function without acquiring the CPU hotplug lock.
Fix the problem by providing both locked and lockless versions of RAPL
APIs.
Fixes: 9eef7f9da9 ("powercap: intel_rapl: Introduce RAPL TPMI interface driver")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Cc: 6.5+ <stable@vger.kernel.org> # 6.5+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CPU temperature can be negative in some cases. Thus the negative CPU
temperature should not be considered as a failure.
Fix intel_tcc_get_temp() and its users to support negative CPU
temperature.
Fixes: a3c1f066e1 ("thermal/intel: Introduce Intel TCC library")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Cc: 6.3+ <stable@vger.kernel.org> # 6.3+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When the PID coefficients k_* are set via sysfs before the IPA
algorithm is triggered then the coefficients would be overwritten after
IPA throttle() is called. The old configuration values might be
different than the new values estimated by the IPA internal algorithm.
There might be a time delay when this overwriting happens. It
depends on the thermal zone temperature value. The temperature value
needs to cross the first trip point value then IPA algorithms start
operating. Although, the PID coefficients setup time should not be
affected or linked to any later operating phase and values must not be
overwritten.
This patch initializes params->sustainable_power when the governor
binds to thermal zone to avoid overwriting k_*. The basic function won't
be affected, as the k_* still can be estimated if the sustainable_power
is modified.
Signed-off-by: Di Shen <di.shen@unisoc.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove an excess tab character from an otherwise empty code line.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Energy Model framework support modifications at runtime of the power
values. Use the new EM table which is protected with RCU. Align the
code so that this RCU read section is short.
This change is not expected to alter the general functionality.
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Energy Model framework support modifications at runtime of the power
values. Use the new EM table which is protected with RCU. Align the
code so that this RCU read section is short.
This change is not expected to alter the general functionality.
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The current behavior of thermal_zone_trip_update() in the bang-bang
thermal governor may be problematic for trip points with 0 hysteresis,
because when the zone temperature reaches the trip temperature and
stays there, it will then cause the cooling device go "on" and "off"
alternately, which is not desirable.
Address this by requiring the zone temperature to actually fall below
trip->temperature - trip->hysteresis for the cooling device to go off.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The computation in the fair share governor's get_trip_level() function
currently works under the assumption that the temperature ordering of
trips[] in a thermal zone is ascending, which need not be the case.
However, get_trip_level() can be made work regardless of whether or not
the trips table is ordered by temperature in any way, so change it
accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After conversion of this driver to use powercap idle_inject core, this
driver doesn't use target_mwait value. So remove dead code.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h.
of_device.h isn't needed, but mod_devicetable.h and property.h were
implicitly included.
Signed-off-by: Rob Herring <robh@kernel.org>
- Add debugfs-based diagnostics support to the thermal core (Daniel
Lezcano, Dan Carpenter).
- Fix a power allocator thermal governor issue preventing it from
resetting cooling devices sometimes (Di Shen).
- Simplify the thermal netlink API and clean up related code (Rafael J.
Wysocki).
- Make the Intel HFI driver support hibernation and deep suspend
properly (Ricardo Neri).
-----BEGIN PGP SIGNATURE-----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=TPzj
-----END PGP SIGNATURE-----
Merge tag 'thermal-6.8-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more thermal control updates from Rafael Wysocki:
"These add support for debugfs-based diagnostics to the thermal core,
simplify the thermal netlink API, fix system-wide PM support in the
Intel HFI driver and clean up some code.
Specifics:
- Add debugfs-based diagnostics support to the thermal core (Daniel
Lezcano, Dan Carpenter)
- Fix a power allocator thermal governor issue preventing it from
resetting cooling devices sometimes (Di Shen)
- Simplify the thermal netlink API and clean up related code (Rafael
J. Wysocki)
- Make the Intel HFI driver support hibernation and deep suspend
properly (Ricardo Neri)"
* tag 'thermal-6.8-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal/debugfs: Unlock on error path in thermal_debug_tz_trip_up()
thermal: intel: hfi: Add syscore callbacks for system-wide PM
thermal: gov_power_allocator: avoid inability to reset a cdev
thermal: helpers: Rearrange thermal_cdev_set_cur_state()
thermal: netlink: Rework notify API for cooling devices
thermal: core: Use kstrdup_const() during cooling device registration
thermal/debugfs: Add thermal debugfs information for mitigation episodes
thermal/debugfs: Add thermal cooling device debugfs information
thermal: netlink: Pass thermal zone pointer to notify routines
thermal: netlink: Drop thermal_notify_tz_trip_add/delete()
thermal: netlink: Pass pointers to thermal_notify_tz_trip_up/down()
thermal: netlink: Pass pointers to thermal_notify_tz_trip_change()
Merge additional updates for 6.8-rc1 in the thermal core and in the
Intel HFI thermal driver:
- Add debugfs-based diagnostics support to the thermal core (Daniel
Lezcano, Dan Carpenter).
- Fix a power allocator thermal governor issue preventing it from
resetting cooling devices sometimes (Di Shen).
- Simplify the thermal netlink API and clean up related code (Rafael J.
Wysocki).
- Make the Intel HFI driver support hibernation and deep suspend
properly (Ricardo Neri).
* thermal-core:
thermal/debugfs: Unlock on error path in thermal_debug_tz_trip_up()
thermal: gov_power_allocator: avoid inability to reset a cdev
thermal: helpers: Rearrange thermal_cdev_set_cur_state()
thermal: netlink: Rework notify API for cooling devices
thermal: core: Use kstrdup_const() during cooling device registration
thermal/debugfs: Add thermal debugfs information for mitigation episodes
thermal/debugfs: Add thermal cooling device debugfs information
thermal: netlink: Pass thermal zone pointer to notify routines
thermal: netlink: Drop thermal_notify_tz_trip_add/delete()
thermal: netlink: Pass pointers to thermal_notify_tz_trip_up/down()
thermal: netlink: Pass pointers to thermal_notify_tz_trip_change()
* thermal-intel:
thermal: intel: hfi: Add syscore callbacks for system-wide PM
Add a missing mutex_unlock(&thermal_dbg->lock) to this error path.
Fixes: 7ef01f228c ("thermal/debugfs: Add thermal debugfs information for mitigation episodes")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The kernel allocates a memory buffer and provides its location to the
hardware, which uses it to update the HFI table. This allocation occurs
during boot and remains constant throughout runtime.
When resuming from hibernation, the restore kernel allocates a second
memory buffer and reprograms the HFI hardware with the new location as
part of a normal boot. The location of the second memory buffer may
differ from the one allocated by the image kernel.
When the restore kernel transfers control to the image kernel, its HFI
buffer becomes invalid, potentially leading to memory corruption if the
hardware writes to it (the hardware continues to use the buffer from the
restore kernel).
It is also possible that the hardware "forgets" the address of the memory
buffer when resuming from "deep" suspend. Memory corruption may also occur
in such a scenario.
To prevent the described memory corruption, disable HFI when preparing to
suspend or hibernate. Enable it when resuming.
Add syscore callbacks to handle the package of the boot CPU (packages of
non-boot CPUs are handled via CPU offline). Syscore ops always run on the
boot CPU. Additionally, HFI only needs to be disabled during "deep" suspend
and hibernation. Syscore ops only run in these cases.
Cc: 6.1+ <stable@vger.kernel.org> # 6.1+
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
[ rjw: Comment adjustment, subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 0952177f2a ("thermal/core/power_allocator: Update once
cooling devices when temp is low") adds an update flag to avoid
triggering a thermal event when there is no need, and the thermal
cdev is updated once when the temperature is low.
But when the trips are writable, and switch_on_temp is set to be a
higher value, the cooling device state may not be reset to 0,
because last_temperature is smaller than switch_on_temp.
For example:
First:
switch_on_temp=70 control_temp=85;
Then userspace change the trip_temp:
switch_on_temp=45 control_temp=55 cur_temp=54
Then userspace reset the trip_temp:
switch_on_temp=70 control_temp=85 cur_temp=57 last_temp=54
At this time, the cooling device state should be reset to 0.
However, because cur_temp(57) < switch_on_temp(70)
last_temp(54) < switch_on_temp(70) ----> update = false,
update is false, the cooling device state can not be reset.
Using the observation that tz->passive can also be regarded as the
temperature status, set the update flag to the tz->passive value.
When the temperature drops below switch_on for the first time, the
states of cooling devices can be reset once, and tz->passive is updated
to 0. In the next round, because tz->passive is 0, cdev->state will not
be updated.
By using the tz->passive value as the "update" flag, the issue above
can be solved, and the cooling devices can be updated only once when the
temperature is low.
Fixes: 0952177f2a ("thermal/core/power_allocator: Update once cooling devices when temp is low")
Cc: 5.13+ <stable@vger.kernel.org> # 5.13+
Suggested-by: Wei Wang <wvw@google.com>
Signed-off-by: Di Shen <di.shen@unisoc.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
