Previously both link-frequency and pixel-rate reported by
the sensor was incorrect, resulting in incorrect FPS.
Report link-frequency in Hz rather than link data rate in bps.
Calculate pixel-rate from link-frequency.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously, initial exposure max was set incorrectly to (0x7fff - 8).
Now, limit exposure max to current resolution (VTS - 8).
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On format change, sometimes, sensor was streaming at a much higher
FPS than the default. This was resulting in various problems like
frame drops/corruption.
Upon format change, set default vblank as current vblank. This will
ensure that sensor will start streaming at default fps.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This prevents potentially scary debug messages from the i2c core.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Amlogic SoC embeds a standalone CEC controller, this patch adds a driver
for such controller.
The controller does not need HPD to be active, and could support up to max
5 logical addresses, but only 1 is handled since the Suspend firmware can
make use of this unique logical address to wake up the device.
The Suspend firmware configuration will be added in an other patchset.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com:s/if (ret)/if (res)/ to fix obvious typo]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Certain syscalls like recvmmsg support 64 bit timespec values for the
X32 ABI. The helper function compat_put_timespec converts a timespec
value to a 32 bit or 64 bit value depending on what ABI is used. The
v4l2 compat layer, however, is not designed to support 64 bit timespec
values and always uses 32 bit values. Hence, compat_put_timespec must
not be used.
Without this patch, user space will be provided with bad timestamp
values from the VIDIOC_DQEVENT ioctl. Also, fields of the struct
v4l2_event32 that come immediately after timestamp get overwritten,
namely the field named id.
Fixes: 81993e81a9 ("compat: Get rid of (get|put)_compat_time(val|spec)")
Cc: stable@vger.kernel.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Tiffany Lin <tiffany.lin@mediatek.com>
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Daniel Mentz <danielmentz@google.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit b2787845fb ("V4L/DVB (5289): Add support for video output
overlays.") added the field global_alpha to struct v4l2_window but did
not update the compat layer accordingly. This change adds global_alpha
to struct v4l2_window32 and copies the value for global_alpha back and
forth.
Signed-off-by: Daniel Mentz <danielmentz@google.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These can only be accessed with CAP_SYS_ADMIN so it's not a critical
security issue. The problem is that "page" is controlled by the user in
the ioctl(). The test to see if the bit is set in state->info->page_mask
is not sufficient because "page" can be very high and shift wrap around
to a bit which is set.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
vpbe_dev_ops is only copied into the ops field at the end of a vpbe_device
structure, so it can be const.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
24 GPIO pins from 32 available on solo6x10 chips are exported
to gpiolib. First 8 GPIOs are reserved for internal use on capture card
boards, GPIOs in range 8:15 are configured as outputs to control relays,
remaining 16:31 are configured as inputs to read sensor states.
Now with this patch userspace DVR software can switch relays and read
sensor states when GPIO extension cards are attached to Softlogic solo6x10
based video capture cards.
Signed-off-by: Anton Sviridenko <anton@corp.bluecherry.net>
Signed-off-by: Ismael Luceno <ismael@iodev.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
No one cares anyway.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While at it, change the type of the previously always-zero i2c_rc
member to int, matching the returned type from i2c_add_adapter.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <media/drv-intf/saa7146.h>
and <linux/pci.h> work with const pci_device_id. So mark the non-const
structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <media/drv-intf/saa7146.h>
and <linux/pci.h> work with const pci_device_id. So mark the non-const
structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <media/drv-intf/saa7146.h>
and <linux/pci.h> work with const pci_device_id. So mark the non-const
structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <media/drv-intf/saa7146.h>
and <linux/pci.h> work with const pci_device_id. So mark the non-const
structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <media/drv-intf/saa7146.h>
and <linux/pci.h> work with const pci_device_id. So mark the non-const
structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <media/drv-intf/saa7146.h>
and <linux/pci.h> work with const pci_device_id. So mark the non-const
structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <media/drv-intf/saa7146.h>
and <linux/pci.h> work with const pci_device_id. So mark the non-const
structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <media/drv-intf/saa7146.h>
and <linux/pci.h> work with const pci_device_id. So mark the non-const
structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If cec_debug >= 1 then log why the requested mode returned -EINVAL.
It can be hard to debug this since -EINVAL can be returned for many
reasons. So this should help.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use the new CEC_CAP_DEFAULTS define in the adv, vivid, pulse8 and
rainshadow CEC drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The SMPTE-2084 transfer functions maps to the luminance range of
0-10000 cd/m^2. Other transfer functions use the traditional range of
0-100 cd/m^2.
I didn't take this into account so the luminance was off by a factor of
100.
Since qv4l2 made the same mistake in reverse I never noticed this until
I tested with actual SMPTE-2084 video.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The on-chip SRAM of i.MX6S is only 128 KiB. 4 KiB of that are allocated
for suspend to RAM since commit df595746fa ("ARM: imx: add suspend in
ocram support for i.mx6q"). Reduce the requested IRAM size to 124 KiB to
avoid an allocation failure that causes the coda driver to not use the
SRAM at all.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
coda_command_sync calls coda_command_async, which writes the
bit_stream_param context variable into the BIT_STREAM_PARAM register,
overwriting the previously set value during coda_start_decoding. Instead
of writing to the register, set bit_stream_param to ensure that the
decoder sequence init command is executed with the escape flag set.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some debug output whose log level is set 1 flooded the log.
Their log level is lowered to find the important log easily.
Signed-off-by: Hirokazu Honda <hiroh@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Passing uninitialized flags into device_prep_interleaved_dma is clearly
a bad idea, and we get a compiler warning for it:
drivers/media/platform/omap/omap_vout_vrfb.c: In function 'omap_vout_prepare_vrfb':
drivers/media/platform/omap/omap_vout_vrfb.c:273:5: error: 'flags' may be used uninitialized in this function [-Werror=maybe-uninitialized]
It seems that the OMAP dmaengine ignores the flags, but we should
pick the right ones anyway. This sets the flags I guessed based
on what other drivers used, and Peter confirmed that they are the
right ones.
Fixes: 6a1560ecaa ("media: v4l: omap_vout: vrfb: Convert to dmaengine")
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
__WARN() cannot be used in portable code, since it is only
available on some architectures and configurations:
drivers/media/platform/pxa_camera.c: In function 'pxa_mbus_config_compatible':
drivers/media/platform/pxa_camera.c:642:3: error: implicit declaration of function '__WARN'; did you mean '__WALL'? [-Werror=implicit-function-declaration]
The common way to express an unconditional warning is WARN_ON(1),
so let's use that here.
Fixes: 97bbdf02d9 ("media: v4l: Add support for CSI-1 and CCP2 busses")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The new ov5670 driver fails to build when VIDEO_V4L2_SUBDEV_API
or MEDIA_CONTROLLER are disabled:
drivers/media/i2c/ov5670.c: In function 'ov5670_open':
drivers/media/i2c/ov5670.c:1917:5: error: implicit declaration of function 'v4l2_subdev_get_try_format'; did you mean 'v4l2_subdev_notify_event'? [-Werror=implicit-function-declaration]
v4l2_subdev_get_try_format(sd, fh->pad, 0);
^~~~~~~~~~~~~~~~~~~~~~~~~~
v4l2_subdev_notify_event
drivers/media/i2c/ov5670.c:1917:38: error: 'struct v4l2_subdev_fh' has no member named 'pad'
v4l2_subdev_get_try_format(sd, fh->pad, 0);
^~
drivers/media/i2c/ov5670.c: In function 'ov5670_do_get_pad_format':
drivers/media/i2c/ov5670.c:2198:17: error: invalid type argument of unary '*' (have 'int')
fmt->format = *v4l2_subdev_get_try_format(&ov5670->sd, cfg,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
fmt->pad);
~~~~~~~~~
drivers/media/i2c/ov5670.c: At top level:
drivers/media/i2c/ov5670.c:2444:19: error: 'v4l2_subdev_link_validate' undeclared here (not in a function); did you mean 'v4l2_subdev_init'?
.link_validate = v4l2_subdev_link_validate,
^~~~~~~~~~~~~~~~~~~~~~~~~
v4l2_subdev_init
drivers/media/i2c/ov5670.c: In function 'ov5670_probe':
drivers/media/i2c/ov5670.c:2492:12: error: 'struct v4l2_subdev' has no member named 'entity'
This adds both to the Kconfig entry.
Fixes: 5de35c9b8d ("media: i2c: Add Omnivision OV5670 5M sensor support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now, we can use of_graph_get_remote_endpoint(). Let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Without this header, we get a build error in some configurations:
drivers/media/platform/omap/omap_vout_vrfb.c: In function 'omap_vout_setup_vrfb_bufs':
drivers/media/platform/omap/omap_vout_vrfb.c:143:26: error: implicit declaration of function 'kzalloc'; did you mean 'vzalloc'? [-Werror=implicit-function-declaration]
Fixes: 6a1560ecaa ("media: v4l: omap_vout: vrfb: Convert to dmaengine")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix missing mutex_destroy() when probe fails and
when driver is removed.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix The camera has a blurry screen phenomenon when
we video chat with apprtc using vp9 codec
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
Reviewed-by: Wu-Cheng Li <wuchengli@chromium.org>
Tested-by: Wu-Cheng Li <wuchengli@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When devm_clk_get() fails the real error code should be propagated,
instead of always returning -EPROBE_DEFER.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
My eye fell on this wrong coefficient in the bt2020_full matrix.
The bt2020 matrix (limited range) is OK.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Set media_version to LINUX_VERSION_CODE, just as we did for
driver_version.
Nobody ever rememebers to update the version number, but
LINUX_VERSION_CODE will always be updated.
Move the MEDIA_API_VERSION define to the ifndef __KERNEL__ section of the
media.h header. That way kernelspace can't accidentally start to use
it again.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since the driver_version field in struct media_device is no longer
used, just remove it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This field will be removed as it is not needed anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This field will be removed as it is not needed anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't use driver_version from struct media_device, just return
LINUX_VERSION_CODE as the other media subsystems do.
The driver_version field in struct media_device will be removed
in the following patches.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver recently switched from handling page flip completion in the
DU vertical blanking handler to the VSP frame end handler to fix a race
condition. This unfortunately resulted in incorrect timestamps in the
vertical blanking events sent to userspace as vertical blanking is now
handled after sending the event.
To fix this we must reverse the order of the two operations. The easiest
way is to handle vertical blanking in the VSP frame end handler before
sending the event. The VSP frame end interrupt occurs approximately 50µs
earlier than the DU frame end interrupt, but this should not cause any
undue harm.
As we need to handle vertical blanking even when page flip completion is
delayed, the VSP driver now needs to call the frame end completion
callback unconditionally, with a new argument to report whether page
flip has completed.
With this new scheme the DU vertical blanking interrupt isn't needed
anymore, so we can stop enabling it.
Fixes: d503a43ac0 ("drm: rcar-du: Register a completion callback with VSP1")
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The VSP supports both header and headerless display lists. The latter is
easier to use when the VSP feeds data directly to the DU in continuous
mode, and the driver thus uses headerless display lists for DU operation
and header display lists otherwise.
Headerless display lists are only available on WPF.0. This has never
been an issue so far, as only WPF.0 is connected to the DU. However, on
H3 ES2.0, the VSP-DL instance has both WPF.0 and WPF.1 connected to the
DU. We thus can't use headerless display lists unconditionally for DU
operation.
Implement support for continuous mode with header display lists, and use
it for DU operation on WPF outputs that don't support headerless mode.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The R-Car H3 ES2.0 VSP-DL instance has two LIF entities and can drive
two display pipelines at the same time. Refactor the VSP DRM code to
support that by introducing a vsp_drm_pipeline object that models one
display pipeline.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The VSP2-DL instance (present in the H3 ES2.0 and M3-N SoCs) has two LIF
instances. Adapt the driver infrastructure to support multiple LIFs.
Support for multiple display pipelines will be added separately.
The change to the entity routing table removes the ability to connect
the LIF output to the HGO or HGT histogram generators. This feature is
only available on Gen2 hardware, isn't supported by the rest of the
driver, and has no known use case, so this isn't an issue.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
New Gen3 SoCs come with two new VSP2 variants names VSP2-BS and VSP2-DL,
as well as a new VSP2-D variant on V3M and V3H SoCs. Add new entries for
them in the VSP device info table.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Blend/ROP Sub Unit (BRS) is a stripped-down version of the BRU found
in several VSP2 instances. Compared to a regular BRU, it supports two
inputs only, and thus has no ROP unit.
Add support for the BRS by modelling it as a new entity type, but reuse
the vsp1_bru object underneath. Chaining the BRU and BRS entities seems
to be supported by the hardware but isn't implemented yet as it isn't
the primary use case for the BRS.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In the H3 ES2.0 SoC the VSP2-DL instance has two connections to DU
channels that need to be configured independently. Extend the VSP-DU API
with a pipeline index to identify which pipeline the caller wants to
operate on.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the VSP1 is used in a DRM pipeline the driver doesn't register the
media device. Links between entities are not exposed to userspace, but
are still used internally for the sole purpose of setting up internal
source to sink pointers through the link setup handler.
Instead of going through this complex procedure, remove link creation
and set the sink pointers directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The internal VSP entity source and sink pointers are stored as
media_entity pointers, which are then cast to a vsp1_entity. As all
sources and sinks are vsp1_entity instances, we can store the
vsp1_entity pointers directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The sink pointer is used to configure routing inside the VSP, and as
such must point to the next VSP entity in the pipeline. The WPF being a
pipeline terminal sink, its output route can't be configured. The
routing configuration code already handles this correctly without
referring to the sink pointer, which thus doesn't need to be set.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the display start interrupt occurs, we know that the hardware has
finished loading the active display list. The driver then proceeds to
recycle the list, assuming it won't be needed anymore.
This assumption holds true for headerless display lists, as the VSP
doesn't reload the list for the next frame if it hasn't changed.
However, this isn't true anymore for header display lists, as they are
loaded at every frame start regardless of whether they have been
updated.
To prepare for header display lists usage in display pipelines, we need
to postpone recycling the list until it gets replaced by a new one
through a page flip. The driver already does so in the frame end
interrupt handler, so all we need is to skip list recycling in the
display start interrupt handler.
While the active list can be recycled at display start for headerless
display lists, there's no real harm in postponing that to the frame end
interrupt handler in all cases. This simplifies interrupt handling as we
don't need to process the display start interrupt anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The display list headers are filled using information from the display
list only. Lower the display list manager spinlock contention by filling
the headers without holding the lock.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Disabling the BWB works around hangups observed while decoding. Since no
issues have been observed while encoding, and disabling BWB also reduces
encoding performance, reenable it for encoding.
Fixes: 89ed025d5c ("[media] coda: disable BWB for all codecs on CODA 960")
Reported-by: Ian Arkver <ian.arkver.dev@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Ian Arkver <ian.arkver.dev@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The OMAP3 ISP supports both external and embedded BT.656 synchronization
for parallel buses. It currently gets the bus type information from the
source subdev through the .g_mbus_config() operation, but should instead
get it from DT as that's the authoritative source of bus configuration
information.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
None of the flash operations are mandatory and therefore there should be
no need for the flash ops structure either. Accept NULL.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The V4L2 flash class initialisation expects struct led_classdev_flash that
describes an indicator but only uses struct led_classdev which is a field
iled_cdev in the struct. Use struct iled_cdev only.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_fwnode_endpoint_alloc_parse() is intended as a replacement for
v4l2_fwnode_endpoint_parse(). It parses the "link-frequency" property and
if the property isn't found, it returns an error. However,
"link-frequency" is an optional property and if it does not exist is not
an error. Instead, the number of link frequencies is simply zero in that
case.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
dev_pm_ops are not supposed to change at runtime. All functions
working with dev_pm_ops provided by <linux/device.h> work with
const dev_pm_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
1195 376 0 1571 623 fimc-is-i2c.o
File size After adding 'const':
text data bss dec hex filename
1403 176 0 1579 62b fimc-is-i2c.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove unnecessary static on local variable rtype. Such variable
is initialized before being used, on every execution path throughout
the function. The static has no benefit and, removing it reduces
the code size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see the difference in the code size. Also,
there is a significant difference in the bss segment. This log is the
output of the size command, before and after the code change:
before:
text data bss dec hex filename
27765 5656 320 33741 83cd drivers/media/i2c/s5k5baf.o
after:
text data bss dec hex filename
27733 5600 256 33589 8335 drivers/media/i2c/s5k5baf.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On Exynos5420, the STREAM_STAT bit raised on the JPGINTST register means
there is a syntax error or an unrecoverable error on compressed file
when ERR_INT_EN is set to 1.
Fix this case and report BUF_STATE_ERROR to videobuf2.
Signed-off-by: Henry-Ruey Hsu <henryhsu@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds support for resolution change event to notify clients so
they can prepare correct output buffer. When resolution change happened,
G_FMT for CAPTURE should return old resolution and format before CAPTURE
queues streamoff.
This event is used in the Chromium browser project by the V4L2 JPEG
Decode Accelerator (V4L2JDA) to allocate output buffer.
Signed-off-by: Henry-Ruey Hsu <henryhsu@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds support for decoding 4:1:1 chroma subsampling in the
JPEG header parsing function.
Signed-off-by: Tony K Nadackal <tony.kn@samsung.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch moves the subsampling value decoding read from the JPEG
header into its own function. This new function is called
s5p_jpeg_subsampling_decode() and returns true if it successfully
decodes the subsampling value, false otherwise.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If s5p_jpeg_parse_hdr() fails to parse the JPEG header, the passed
s5p_jpeg_q_data structure is not modified so there is no need to use a
temporary structure and the field-by-field copy can be avoided.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch modifies the s5p_jpeg_parse_hdr() function so it only
modifies the passed s5p_jpeg_q_data structure if the jpeg header parsing
is successful.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Correct the WARN_ON statement for subsampling based on the
JPEG hardware version.
Signed-off-by: Tony K Nadackal <tony.kn@samsung.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When queuing an OUTPUT buffer for decoder, s5p_jpeg_parse_hdr()
function parses the input jpeg file and takes the width and height
parameters from its header. These new width/height values will be used
for the calculation of stride. HX_JPEG Hardware needs the width and
height values aligned on a 16 bits boundary. This width/height alignment
is handled in the s5p_jpeg_s_fmt_vid_cap() function during the S_FMT
ioctl call.
But if user space calls the QBUF of OUTPUT buffer after the S_FMT of
CAPTURE buffer, these aligned values will be replaced by the values in
jpeg header. If the width/height values of jpeg are not aligned, the
decoder output will be corrupted. So in this patch we call
jpeg_bound_align_image() to align the width/height values of Capture
buffer in s5p_jpeg_buf_queue().
Signed-off-by: Tony K Nadackal <tony.kn@samsung.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drop VPFE_CMD_S_CCDC_RAW_PARAMS ioctl from dm355/dm644x following reasons:
- This ioctl was never in public api and was only defined in kernel header.
- The function set_params constantly mixes up pointers and phys_addr_t
numbers.
- This is part of a 'VPFE_CMD_S_CCDC_RAW_PARAMS' ioctl command that is
described as an 'experimental ioctl that will change in future kernels'.
- The code to allocate the table never gets called after we copy_from_user
the user input over the kernel settings, and then compare them
for inequality.
- We then go on to use an address provided by user space as both the
__user pointer for input and pass it through phys_to_virt to come up
with a kernel pointer to copy the data to. This looks like a trivially
exploitable root hole.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
this patch makes sure VPFE_CMD_S_CCDC_RAW_PARAMS ioctl no longer works
for vpfe_capture driver with a minimal patch suitable for backporting.
- This ioctl was never in public api and was only defined in kernel header.
- The function set_params constantly mixes up pointers and phys_addr_t
numbers.
- This is part of a 'VPFE_CMD_S_CCDC_RAW_PARAMS' ioctl command that is
described as an 'experimental ioctl that will change in future kernels'.
- The code to allocate the table never gets called after we copy_from_user
the user input over the kernel settings, and then compare them
for inequality.
- We then go on to use an address provided by user space as both the
__user pointer for input and pass it through phys_to_virt to come up
with a kernel pointer to copy the data to. This looks like a trivially
exploitable root hole.
Due to these reasons we make sure this ioctl now returns -EINVAL and backport
this patch as far as possible.
Fixes: 5f15fbb68f ("V4L/DVB (12251): v4l: dm644x ccdc module for vpfe capture driver")
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: <stable@vger.kernel.org> # for v3.7 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In venus_boot(), we pass a pointer to a phys_addr_t
into dmam_alloc_coherent, which the compiler warns about:
platform/qcom/venus/firmware.c: In function 'venus_boot':
platform/qcom/venus/firmware.c:63:49: error: passing argument 3 of 'dmam_alloc_coherent' from incompatible pointer type [-Werror=incompatible-pointer-types]
To avoid the error refactor venus_boot function by discard
dma_alloc_coherent invocation because we don't want to map the
memory for the device. Something more, the usage of
DMA mapping API is actually wrong and the current
implementation relies on several bugs in DMA mapping code.
When these bugs are fixed that will break firmware loading,
so fix this now to avoid future troubles.
The meaning of venus_boot is to copy the content of the
firmware buffer into reserved (and memblock removed)
block of memory and pass that physical address to the
trusted zone for authentication and mapping through iommu
form the secure world. After iommu mapping is done the iova
is passed as ane entry point to the remote processor.
After this change memory-region property is parsed manually
and the physical address is memremap to CPU, call mdt_load to
load firmware segments into proper places and unmap
reserved memory.
Fixes: af2c3834c8 ("[media] media: venus: adding core part and helper functions")
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Not entirely sure what triggers it, but with venus build as kernel
module and in initrd, we hit this crash:
Unable to handle kernel paging request at virtual address ffff80003c039000
pgd = ffff00000a14f000
[ffff80003c039000] *pgd=00000000bd9f7003, *pud=00000000bd9f6003, *pmd=00000000bd9f0003, *pte=0000000000000000
Internal error: Oops: 96000007 [#1] SMP
Modules linked in: qcom_wcnss_pil(E+) crc32_ce(E) qcom_common(E) venus_core(E+) remoteproc(E) snd_soc_msm8916_digital(E) virtio_ring(E) cdc_ether(E) snd_soc_lpass_apq8016(E) snd_soc_lpass_cpu(E) snd_soc_apq8016_sbc(E) snd_soc_lpass_platform(E) v4l2_mem2mem(E) virtio(E) snd_soc_core(E) ac97_bus(E) snd_pcm_dmaengine(E) snd_seq(E) leds_gpio(E) videobuf2_v4l2(E) videobuf2_core(E) snd_seq_device(E) snd_pcm(E) videodev(E) media(E) nvmem_qfprom(E) msm(E) snd_timer(E) snd(E) soundcore(E) spi_qup(E) mdt_loader(E) qcom_tsens(E) qcom_spmi_temp_alarm(E) nvmem_core(E) msm_rng(E) uas(E) usb_storage(E) dm9601(E) usbnet(E) mii(E) mmc_block(E) adv7511(E) drm_kms_helper(E) syscopyarea(E) sysfillrect(E) sysimgblt(E) fb_sys_fops(E) qcom_spmi_vadc(E) qcom_vadc_common(PE) industrialio(E) pinctrl_spmi_mpp(E)
pinctrl_spmi_gpio(E) rtc_pm8xxx(E) clk_smd_rpm(E) sdhci_msm(E) sdhci_pltfm(E) qcom_smd_regulator(E) drm(E) smd_rpm(E) qcom_spmi_pmic(E) regmap_spmi(E) ci_hdrc_msm(E) ci_hdrc(E) usb3503(E) extcon_usb_gpio(E) phy_msm_usb(E) udc_core(E) qcom_hwspinlock(E) extcon_core(E) ehci_msm(E) i2c_qup(E) sdhci(E) mmc_core(E) spmi_pmic_arb(E) spmi(E) qcom_smd(E) smsm(E) rpmsg_core(E) smp2p(E) smem(E) hwspinlock_core(E) gpio_keys(E)
CPU: 2 PID: 551 Comm: irq/150-venus Tainted: P E 4.12.0+ #1625
Hardware name: qualcomm dragonboard410c/dragonboard410c, BIOS 2017.07-rc2-00144-ga97bdbdf72-dirty 07/08/2017
task: ffff800037338000 task.stack: ffff800038e00000
PC is at hfi_sys_init_done+0x64/0x140 [venus_core]
LR is at hfi_process_msg_packet+0xcc/0x1e8 [venus_core]
pc : [<ffff00000118b384>] lr : [<ffff00000118c11c>] pstate: 20400145
sp : ffff800038e03c60
x29: ffff800038e03c60 x28: 0000000000000000
x27: 00000000000df018 x26: ffff00000118f4d0
x25: 0000000000020003 x24: ffff80003a8d3010
x23: ffff00000118f760 x22: ffff800037b40028
x21: ffff8000382981f0 x20: ffff800037b40028
x19: ffff80003c039000 x18: 0000000000000020
x17: 0000000000000000 x16: ffff800037338000
x15: ffffffffffffffff x14: 0000001000000014
x13: 0000000100001007 x12: 0000000100000020
x11: 0000100e00000000 x10: 0000000000000001
x9 : 0000000200000000 x8 : 0000001400000001
x7 : 0000000000001010 x6 : 0000000000000148
x5 : 0000000000001009 x4 : ffff80003c039000
x3 : 00000000cd770abb x2 : 0000000000000042
x1 : 0000000000000788 x0 : 0000000000000002
Process irq/150-venus (pid: 551, stack limit = 0xffff800038e00000)
Call trace:
[<ffff00000118b384>] hfi_sys_init_done+0x64/0x140 [venus_core]
[<ffff00000118c11c>] hfi_process_msg_packet+0xcc/0x1e8 [venus_core]
[<ffff00000118a2b4>] venus_isr_thread+0x1b4/0x208 [venus_core]
[<ffff00000118e750>] hfi_isr_thread+0x28/0x38 [venus_core]
[<ffff000008161550>] irq_thread_fn+0x30/0x70
[<ffff0000081617fc>] irq_thread+0x14c/0x1c8
[<ffff000008105e68>] kthread+0x138/0x140
[<ffff000008083590>] ret_from_fork+0x10/0x40
Code: 52820125 52820207 7a431820 54000249 (b9400263)
---[ end trace c963460f20a984b6 ]---
The problem is that in the error case, we've incremented the data ptr
but not decremented rem_bytes, and keep reading (presumably garbage)
until eventually we go beyond the end of the buffer.
Instead, on first error, we should probably just bail out. Other
option is to increment read_bytes by sizeof(u32) before the switch,
rather than only accounting for the ptype header in the non-error
case. Note that in this case it is HFI_ERR_SYS_INVALID_PARAMETER,
ie. an unrecognized/unsupported parameter, so interpreting the next
word as a property type would be bogus. The other error cases are
due to truncated buffer, so there isn't likely to be anything valid
to interpret in the remainder of the buffer. So just bailing seems
like a reasonable solution.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If QCOM_MDT_LOADER is enabled, but ARCH_QCOM is not, we run into
a build error:
ERROR: "qcom_mdt_load" [drivers/media/platform/qcom/venus/venus-core.ko] undefined!
ERROR: "qcom_mdt_get_size" [drivers/media/platform/qcom/venus/venus-core.ko] undefined!
This changes the 'select' statement again, so we only try to enable
those symbols when the drivers will actually get built, and explicitly
test for QCOM_MDT_LOADER to be enabled before calling into it.
Fixes: 76724b30f2 ("[media] media: venus: enable building with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Without PM support, gcc warns about two unused functions:
platform/qcom/venus/core.c:146:13: error: 'venus_clks_disable' defined but not used [-Werror=unused-function]
platform/qcom/venus/core.c:126:12: error: 'venus_clks_enable' defined but not used [-Werror=unused-function]
The problem as usual are incorrect #ifdefs, so the easiest fix
is to do away with the #ifdef completely and mark the suspend/resume
handlers as __maybe_unused, which they are.
Fixes: af2c3834c8 ("[media] media: venus: adding core part and helper functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Allow calling cec_notifier_set_phys_addr and
cec_notifier_set_phys_addr_from_edid with a NULL notifier, in which
case these functions do nothing.
Add a cec_notifier_phys_addr_invalidate helper function (the notifier
equivalent of cec_phys_addr_invalidate).
These changes simplify drm CEC driver support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The persistent_config option is used to make the CEC settings persistent by using
the eeprom inside the device to store this information. This was on by default, which
caused confusion since this device now behaves differently from other CEC devices
which all come up unconfigured.
Another reason for doing this now is that I hope a more standard way of selecting
persistent configuration will be created in the future. And for that to work all
CEC drivers should behave the same and come up unconfigured by default.
None of the open source CEC applications are using this CEC framework at the moment
so change this behavior before it is too late.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.10 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The switch in cec_transmit_attempt_done() should ignore the
CEC_TX_STATUS_MAX_RETRIES status bit.
Calling this function with e.g. CEC_TX_STATUS_NACK | CEC_TX_STATUS_MAX_RETRIES
is perfectly legal and should not trigger the WARN(1).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit e8f4818895 ("[media] lirc: advertise
LIRC_CAN_GET_REC_RESOLUTION and improve") lircd uses the ioctl
LIRC_GET_REC_RESOLUTION to determine the shortest pulse or space that
the hardware can detect. This breaks decoding in lirc because lircd
expects the answer in microseconds, but nanoseconds is returned.
Cc: <stable@vger.kernel.org> # v2.6.36+
Reported-by: Derek <user.vdr@gmail.com>
Tested-by: Derek <user.vdr@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The vimc platform drivers define a platform device ID table but these
are not set to the .id_table field in the platform driver structure.
So the platform device ID table is only used to fill the aliases in
the module but are not used for matching (works because the platform
subsystem fallbacks to the driver's name if no .id_table is set).
But this also means that the platform device ID table isn't used if
the driver is built-in, which leads to the following build warning:
This causes the following build warnings when the driver is built-in:
drivers/media/platform/vimc//vimc-capture.c:528:40: warning: ‘vimc_cap_driver_ids’ defined but not used [-Wunused-const-variable=]
static const struct platform_device_id vimc_cap_driver_ids[] = {
^~~~~~~~~~~~~~~~~~~
drivers/media/platform/vimc//vimc-debayer.c:588:40: warning: ‘vimc_deb_driver_ids’ defined but not used [-Wunused-const-variable=]
static const struct platform_device_id vimc_deb_driver_ids[] = {
^~~~~~~~~~~~~~~~~~~
drivers/media/platform/vimc//vimc-scaler.c:442:40: warning: ‘vimc_sca_driver_ids’ defined but not used [-Wunused-const-variable=]
static const struct platform_device_id vimc_sca_driver_ids[] = {
^~~~~~~~~~~~~~~~~~~
drivers/media/platform/vimc//vimc-sensor.c:376:40: warning: ‘vimc_sen_driver_ids’ defined but not used [-Wunused-const-variable=]
static const struct platform_device_id vimc_sen_driver_ids[] = {
^~~~~~~~~~~~~~~~~~~
Reported-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Suggested-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix this kernel-doc warning:
WARNING: kernel-doc 'media-git/scripts/kernel-doc -rst -enable-lineno media-git/drivers/media/dvb-core/demux.h' processing failed with: 'ascii' codec can't decode byte 0xe2 in position 6368: ordinal
not in range(128)
Caused by using fancy quotes instead of regular quotes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The local pad parameter in media_entity_remote_pad() is not modified.
Make that explicit by adding a const modifier.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Declare v4l2_file_operations structures as const as they are only stored
in the fops field of video_device structures. This field is of type
const, so declare v4l2_file_operations structures with similar properties
as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This function is used only internally. So, make it static.
Shuts up this warning:
drivers/media/v4l2-core/v4l2-fwnode.c:153:6: warning: no previous prototype for 'v4l2_fwnode_endpoint_parse_csi1_bus' [-Wmissing-prototypes]
void v4l2_fwnode_endpoint_parse_csi1_bus(struct fwnode_handle *fwnode,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
smatch produce this warning:
drivers/media/v4l2-core/v4l2-fwnode.c:76 v4l2_fwnode_endpoint_parse_csi_bus() error: buffer overflow 'array' 5 <= u16max
That's because, in thesis, the routine might have called with
some value at bus->num_data_lanes. That's not the current
case.
Yet, better to shut up this warning, and make the code more
reliable if some future changes might cause a bug.
While here, simplify the code a little bit by reading only
once from lanes-properties array.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As reported by this warning:
drivers/media/usb/pvrusb2/pvrusb2-encoder.c:263 pvr2_encoder_cmd() warn: continue to end of do { ... } while(0); loop
There's an issue at the retry logic there: the current logic is:
do {
if (need_to_retry)
continue;
some_code();
} while (0);
Well, that won't work, as continue will make it test for zero, and
abort the loop. So, change the loop to:
while (1) {
if (need_to_retry)
continue;
some_code();
break;
};
With seems to be what's actually expected there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is used just for printing a version number. As this is
never incremented, it makes no sense to keep it :-)
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We seldomly increment version numbers on drivers, because... we
usually forget ;-)
So, instead, just make it identical to the Kernel version, as what
we do on all other drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Sylwester Nawrocki <snawrocki@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drop VPFE_CMD_S_CCDC_RAW_PARAMS ioctl from dm355/dm644x following reasons:
- This ioctl was never in public api and was only defined in kernel header.
- The function set_params constantly mixes up pointers and phys_addr_t
numbers.
- This is part of a 'VPFE_CMD_S_CCDC_RAW_PARAMS' ioctl command that is
described as an 'experimental ioctl that will change in future kernels'.
- The code to allocate the table never gets called after we copy_from_user
the user input over the kernel settings, and then compare them
for inequality.
- We then go on to use an address provided by user space as both the
__user pointer for input and pass it through phys_to_virt to come up
with a kernel pointer to copy the data to. This looks like a trivially
exploitable root hole.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
this patch makes sure VPFE_CMD_S_CCDC_RAW_PARAMS ioctl no longer works
for vpfe_capture driver with a minimal patch suitable for backporting.
- This ioctl was never in public api and was only defined in kernel header.
- The function set_params constantly mixes up pointers and phys_addr_t
numbers.
- This is part of a 'VPFE_CMD_S_CCDC_RAW_PARAMS' ioctl command that is
described as an 'experimental ioctl that will change in future kernels'.
- The code to allocate the table never gets called after we copy_from_user
the user input over the kernel settings, and then compare them
for inequality.
- We then go on to use an address provided by user space as both the
__user pointer for input and pass it through phys_to_virt to come up
with a kernel pointer to copy the data to. This looks like a trivially
exploitable root hole.
Due to these reasons we make sure this ioctl now returns -EINVAL and backport
this patch as far as possible.
Fixes: 5f15fbb68f ("V4L/DVB (12251): v4l: dm644x ccdc module for vpfe capture driver")
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: <stable@vger.kernel.org> # for v3.7 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In venus_boot(), we pass a pointer to a phys_addr_t
into dmam_alloc_coherent, which the compiler warns about:
platform/qcom/venus/firmware.c: In function 'venus_boot':
platform/qcom/venus/firmware.c:63:49: error: passing argument 3 of 'dmam_alloc_coherent' from incompatible pointer type [-Werror=incompatible-pointer-types]
To avoid the error refactor venus_boot function by discard
dma_alloc_coherent invocation because we don't want to map the
memory for the device. Something more, the usage of
DMA mapping API is actually wrong and the current
implementation relies on several bugs in DMA mapping code.
When these bugs are fixed that will break firmware loading,
so fix this now to avoid future troubles.
The meaning of venus_boot is to copy the content of the
firmware buffer into reserved (and memblock removed)
block of memory and pass that physical address to the
trusted zone for authentication and mapping through iommu
form the secure world. After iommu mapping is done the iova
is passed as ane entry point to the remote processor.
After this change memory-region property is parsed manually
and the physical address is memremap to CPU, call mdt_load to
load firmware segments into proper places and unmap
reserved memory.
Fixes: af2c3834c8 ("[media] media: venus: adding core part and helper functions")
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Not entirely sure what triggers it, but with venus build as kernel
module and in initrd, we hit this crash:
Unable to handle kernel paging request at virtual address ffff80003c039000
pgd = ffff00000a14f000
[ffff80003c039000] *pgd=00000000bd9f7003, *pud=00000000bd9f6003, *pmd=00000000bd9f0003, *pte=0000000000000000
Internal error: Oops: 96000007 [#1] SMP
Modules linked in: qcom_wcnss_pil(E+) crc32_ce(E) qcom_common(E) venus_core(E+) remoteproc(E) snd_soc_msm8916_digital(E) virtio_ring(E) cdc_ether(E) snd_soc_lpass_apq8016(E) snd_soc_lpass_cpu(E) snd_soc_apq8016_sbc(E) snd_soc_lpass_platform(E) v4l2_mem2mem(E) virtio(E) snd_soc_core(E) ac97_bus(E) snd_pcm_dmaengine(E) snd_seq(E) leds_gpio(E) videobuf2_v4l2(E) videobuf2_core(E) snd_seq_device(E) snd_pcm(E) videodev(E) media(E) nvmem_qfprom(E) msm(E) snd_timer(E) snd(E) soundcore(E) spi_qup(E) mdt_loader(E) qcom_tsens(E) qcom_spmi_temp_alarm(E) nvmem_core(E) msm_rng(E) uas(E) usb_storage(E) dm9601(E) usbnet(E) mii(E) mmc_block(E) adv7511(E) drm_kms_helper(E) syscopyarea(E) sysfillrect(E) sysimgblt(E) fb_sys_fops(E) qcom_spmi_vadc(E) qcom_vadc_common(PE) industrialio(E) pinctrl_spmi_mpp(E)
pinctrl_spmi_gpio(E) rtc_pm8xxx(E) clk_smd_rpm(E) sdhci_msm(E) sdhci_pltfm(E) qcom_smd_regulator(E) drm(E) smd_rpm(E) qcom_spmi_pmic(E) regmap_spmi(E) ci_hdrc_msm(E) ci_hdrc(E) usb3503(E) extcon_usb_gpio(E) phy_msm_usb(E) udc_core(E) qcom_hwspinlock(E) extcon_core(E) ehci_msm(E) i2c_qup(E) sdhci(E) mmc_core(E) spmi_pmic_arb(E) spmi(E) qcom_smd(E) smsm(E) rpmsg_core(E) smp2p(E) smem(E) hwspinlock_core(E) gpio_keys(E)
CPU: 2 PID: 551 Comm: irq/150-venus Tainted: P E 4.12.0+ #1625
Hardware name: qualcomm dragonboard410c/dragonboard410c, BIOS 2017.07-rc2-00144-ga97bdbdf72-dirty 07/08/2017
task: ffff800037338000 task.stack: ffff800038e00000
PC is at hfi_sys_init_done+0x64/0x140 [venus_core]
LR is at hfi_process_msg_packet+0xcc/0x1e8 [venus_core]
pc : [<ffff00000118b384>] lr : [<ffff00000118c11c>] pstate: 20400145
sp : ffff800038e03c60
x29: ffff800038e03c60 x28: 0000000000000000
x27: 00000000000df018 x26: ffff00000118f4d0
x25: 0000000000020003 x24: ffff80003a8d3010
x23: ffff00000118f760 x22: ffff800037b40028
x21: ffff8000382981f0 x20: ffff800037b40028
x19: ffff80003c039000 x18: 0000000000000020
x17: 0000000000000000 x16: ffff800037338000
x15: ffffffffffffffff x14: 0000001000000014
x13: 0000000100001007 x12: 0000000100000020
x11: 0000100e00000000 x10: 0000000000000001
x9 : 0000000200000000 x8 : 0000001400000001
x7 : 0000000000001010 x6 : 0000000000000148
x5 : 0000000000001009 x4 : ffff80003c039000
x3 : 00000000cd770abb x2 : 0000000000000042
x1 : 0000000000000788 x0 : 0000000000000002
Process irq/150-venus (pid: 551, stack limit = 0xffff800038e00000)
Call trace:
[<ffff00000118b384>] hfi_sys_init_done+0x64/0x140 [venus_core]
[<ffff00000118c11c>] hfi_process_msg_packet+0xcc/0x1e8 [venus_core]
[<ffff00000118a2b4>] venus_isr_thread+0x1b4/0x208 [venus_core]
[<ffff00000118e750>] hfi_isr_thread+0x28/0x38 [venus_core]
[<ffff000008161550>] irq_thread_fn+0x30/0x70
[<ffff0000081617fc>] irq_thread+0x14c/0x1c8
[<ffff000008105e68>] kthread+0x138/0x140
[<ffff000008083590>] ret_from_fork+0x10/0x40
Code: 52820125 52820207 7a431820 54000249 (b9400263)
---[ end trace c963460f20a984b6 ]---
The problem is that in the error case, we've incremented the data ptr
but not decremented rem_bytes, and keep reading (presumably garbage)
until eventually we go beyond the end of the buffer.
Instead, on first error, we should probably just bail out. Other
option is to increment read_bytes by sizeof(u32) before the switch,
rather than only accounting for the ptype header in the non-error
case. Note that in this case it is HFI_ERR_SYS_INVALID_PARAMETER,
ie. an unrecognized/unsupported parameter, so interpreting the next
word as a property type would be bogus. The other error cases are
due to truncated buffer, so there isn't likely to be anything valid
to interpret in the remainder of the buffer. So just bailing seems
like a reasonable solution.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If QCOM_MDT_LOADER is enabled, but ARCH_QCOM is not, we run into
a build error:
ERROR: "qcom_mdt_load" [drivers/media/platform/qcom/venus/venus-core.ko] undefined!
ERROR: "qcom_mdt_get_size" [drivers/media/platform/qcom/venus/venus-core.ko] undefined!
This changes the 'select' statement again, so we only try to enable
those symbols when the drivers will actually get built, and explicitly
test for QCOM_MDT_LOADER to be enabled before calling into it.
Fixes: 76724b30f2 ("[media] media: venus: enable building with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Without PM support, gcc warns about two unused functions:
platform/qcom/venus/core.c:146:13: error: 'venus_clks_disable' defined but not used [-Werror=unused-function]
platform/qcom/venus/core.c:126:12: error: 'venus_clks_enable' defined but not used [-Werror=unused-function]
The problem as usual are incorrect #ifdefs, so the easiest fix
is to do away with the #ifdef completely and mark the suspend/resume
handlers as __maybe_unused, which they are.
Fixes: af2c3834c8 ("[media] media: venus: adding core part and helper functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As we're already touching on dvb_ca_en50221 to cleanup
checkpatch issues, do that also for its header file, with:
$ ./scripts/checkpatch.pl --strict --fix-inplace -f drivers/media/dvb-core/dvb_ca_en50221.h
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- Running "checkpatch.pl -strict -f ..." gave more checks to fix.
* Blank lines aren't necessary after an open brace '{'
* Comparison to NULL written as "!<var>"
* CHECK: Blank lines aren't necessary before a close brace '}'
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some EXPORT_SYMBOL() on this file don't match the name of functions
that precedes them.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixed most of:
WARNING: line over 80 characters
The remaining lines are printk strings, which should not be split and
lines where I thing they should stay as they are.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- The STATUSREG_TXERR definition is not used and it has style
problems, too. Removing it seems to solve both issues.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Used a helper variable "struct dvb_ca_slot *sl" instead of
"ca->slot_info[slot]". This reduces the line length and simplifies
code reading.
Fixed also "-strict" checks in this patch:
- Comparison to NULL written as "!<var>".
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixed all:
ERROR: do not use assignment in if condition
Fixed also "-strict" checks in this patch:
- Changed "if (ret != 0)" to "if (ret)".
- Camel case variables have been converted to kernel_case.
- Comparison to NULL written as "!<var>".
- No space is necessary after a cast.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixed all:
WARNING: msleep < 20ms can sleep for up to 20ms
by using usleep_range.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CAM poll code for the budget-av is exactly the same on several
places. Extracting the code to a new function improves maintainability.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Refactored "dvb_ca_en50221_thread" by moving the state machine into the
new function "dvb_ca_en50221_thread_state_machine". This reduces the
thread function size and reduces the structural complexity and of course
gives us more space to meet the line length goal in the new function.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While cab_state->state gives a quite accurate indication of the demod
signal status, it might be incorrect if cab_algo() wasn't able to
determine the exact status, with cab_algo() being the only place where
this status was updated from, and it is only called upon tuning to new
parameters passed to set_frontend(). Thus, the status will be wrong
until the demod is retuned. With the cab_signal_type parsing in
read_status(), this results in unusual fe_states like FE_HAS_SIGNAL |
FE_HAS_CARRIER | FE_HAS_LOCK, which, while userspace applications check
for FE_HAS_LOCK and work fine, leads to missing CNR or UCB stats.
Fix this by re-reading CAB_FSM_STATUS and updating cab_state->state() in
read_status(). While at it, refactor the fsm/qamfeclock and the
fsm->signaltype parsing into separate functions to make things cleaner
and deduplicate code. Also, assume full QAM FEC lock equals full
FE_STATUS.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Historically, mdev argument name was being used on both struct
media_device and struct media_devnode. Recently most occurrences of mdev
referring to struct media_devnode were replaced by devnode, which makes
more sense. Fix the last remaining occurrence.
Fixes: 163f1e93e9 ("[media] media-devnode: fix namespace mess")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Simplify the code to satisfy Linux coding style.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate array dib0090_tuning_table_cband_7090e_aci on the stack but
instead make it static. Makes the object code smaller by over 180 bytes:
Before:
text data bss dec hex filename
40052 7320 192 47564 b9cc dib0090.o
After:
text data bss dec hex filename
39780 7408 192 47380 b914 dib0090.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate const arrays on the stack but instead make them static.
Makes the object code smaller by over 1800 bytes:
Before:
text data bss dec hex filename
94100 9160 0 103260 1935c drxj.o
After:
text data bss dec hex filename
91044 10400 0 101444 18c44 drxj.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate arrays slowIncrDecLUT and fastIncrDecLUT on the stack but
instead make them static. Makes the object code smaller by over 100 bytes:
text data bss dec hex filename
27776 832 64 28672 7000 drxd_hard.o
text data bss dec hex filename
27530 976 64 28570 6f9a drxd_hard.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Discovered using w_scan when scanning DVB-T/T2: When w_scan goes from -T
to -T2, it does so without stopping the frontend using .sleep. Due to
this, the demod operation mode isn't re-setup, but as it still is in
STATE_ACTIVE_TC, PLP and T2 Profile are set up, but only retune_active()
is called, leaving the demod in T mode, thus not operable on any T2
frequency.
Fix this by putting the demod to sleep if priv->system isn't equal to
p->delsys. To properly accomplish this, sleep_tc() is split into
sleep_tc() and shutdown_tc(), where sleep_tc() will only perform the
sleep operation, while shutdown_tc() additionally performs the full
demod shutdown (to keep the behaviour when the .sleep FE_OP is called).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate array gamma_par_mask on the stack but instead make it
static. Makes the object code smaller by 148 bytes:
Before:
text data bss dec hex filename
2993 1104 0 4097 1001 drivers/staging/fbtft/fb_st7789v.o
After:
text data bss dec hex filename
2757 1192 0 3949 f6d drivers/staging/fbtft/fb_st7789v.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate arrays on the stack but make them static. Makes
the object code smaller:
Before:
text data bss dec hex filename
89299 21704 64 111067 1b1db cxd2841er.o
After:
text data bss dec hex filename
85823 23432 64 109319 1ab07 cxd2841er.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When a user starts and stops filtering at a demux device too quickly
in a very short interval, the user process hangs in uninterruptible sleep,
due to an inconsistency of kthread status in the driver.
The kthread can be stopped before it starts running its thread function,
but the invocation status was partly managed in the kthread function,
which resulted in a double kthread_stop() of one kthread.
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Return 0 instead of -EINVAL in get_frontend if no demod mode is active.
This fixes ie. dvb-fe-tool getting confused and assuming a DVBv3 FE on idle
frontends when the FE has been put to sleep using sleep().
Also, in read_status(), don't immediately return when no demod is active,
so the remaining code has a chance to clear the signal statistics.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds a stv0910_single modparm which, when set, configures the stv0910 to
run in single demodulator mode, currently intended for high bit rate
testing.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds all required glue code to support - in conjunction with the new
stv0910 and stv6111 demod/tuner drivers and additionally the lnbh25 LNB
controller driver - all current DVB-S/S2 hardware (bridges and flex
modules) from Digital Devices like the DD CineS2 V7 and V7A, current
S2 V4 DuoFlex modules, and probably all upcoming devices based on this
STV0910/STV6111/LNBH25 hardware stack.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The returned value is required for further evaluation of the exact
demodulator chip (stv090x or stv0910).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds a frontend driver for the ST STV6111 DVB-S/S2 tuners. Like the
stv0910 demod frontend driver, this driver originates from the Digital
Devices' dddvb vendor driver package as of version 0.9.29, and was cleaned
up aswell. No functionality had to be removed though. Any camel case has
been converted to kernel_case, fixup patch has been proposed upstream.
Permission to reuse and mainline the driver code was formally granted by
Ralph Metzler <rjkm@metzlerbros.de>.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This was missing from the frontend_ops.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Original code at least has some signed/unsigned issues, resulting in
values like 32dBm. Implement signal strength readout to work without
asking the attached tuner, and use a lookup table instead of log calc.
Values reported appear plausible, gathered from feedback from several
testers.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implements stream_id filter and scrambling code setup in start() and also
sets FE_CAN_MULTISTREAM in frontend_ops. This enables the driver to
properly receive and handle multistream transponders, functionality has
been reported working fine by testers with access to such streams, in
conjunction with VDR on the userspace side.
The code snippet originates from the original vendor's dddvb driver
package and has been made working properly with the current in-kernel
DVB core API.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixes smatch error:
drivers/media/dvb-frontends/stv0910.c:715 dvbs2_nbch() error: buffer overflow 'nbch[fectype]' 2 <= 28
Also, fixes the nbch array table by adding the DUMMY_PLF element at the top
to match the enums (table element order was off by one before).
Patch sent upstream aswell.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds a multi frontend driver for the ST STV0910 DVB-S/S2 demodulator
frontends. The driver code originates from the Digital Devices' dddvb
vendor driver package as of version 0.9.29, and has been cleaned up from
core API usage which isn't supported yet in the kernel, and additionally
all obvious style issues have been resolved. All camel case and allcaps
have been converted to kernel_case and lowercase. Patches have been sent
to the vendor package maintainers to fix this aswell. Signal statistics
acquisition has been refactored to comply with standards.
Permission to reuse and mainline the driver code was formally granted by
Ralph Metzler <rjkm@metzlerbros.de>.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that the multiplexer framework is merged, drop the temporary
mmio-mux implementation from the video-mux driver and convert it to use
the multiplexer API.
[mchehab@s-opensource.com: fix a merge conflict at Kconfig]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
gcc-7 notices that we copy a fixed length string into another
string of the same size, with additional characters:
drivers/media/usb/usbvision/usbvision-i2c.c: In function 'usbvision_i2c_register':
drivers/media/usb/usbvision/usbvision-i2c.c:190:36: error: '%d' directive writing between 1 and 11 bytes into a region of size between 0 and 47 [-Werror=format-overflow=]
sprintf(usbvision->i2c_adap.name, "%s-%d-%s", i2c_adap_template.name,
^~~~~~~~~~
drivers/media/usb/usbvision/usbvision-i2c.c:190:2: note: 'sprintf' output between 4 and 76 bytes into a destination of size 48
Using snprintf() makes the code more robust in general, but will still
trigger a possible warning about truncation in the string.
We know this won't happen as the template name is always "usbvision", so
we can easily avoid the warning as well by using this as the format string
directly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch enables support for non-Bluecherry labeled solo6110
based PCI cards which have 3 x TW2864B chips and one TW2865.
These cards are displayed by lspci -nn as
"Softlogic Co., Ltd. SOLO6110 H.264 Video encoder/decoder [9413:6110]"
Bluecherry cards have 4 x TW2864A. According to datasheet register 0xFF
of TW2864B chips contains value 0x6A or 0x6B depending on revision
which being shifted 3 bits right gives value 0x0d.
Existing version of solo6x10 fails on these cards with
[276582.344942] solo6x10 0000:07:00.0: Probing Softlogic 6110
[276582.402151] solo6x10 0000:07:00.0: Could not initialize any techwell chips
[276582.402781] solo6x10: probe of 0000:07:00.0 failed with error -22
Signed-off-by: Anton Sviridenko <anton@corp.bluecherry.net>
Acked-by: Andrey Utkin <andrey_utkin@fastmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drivers/media/i2c/adv748x/adv748x-csi2.c: In function 'adv748x_csi2_init_controls':
drivers/media/i2c/adv748x/adv748x-csi2.c:251:20: warning: variable 'ctrl' set but not used [-Wunused-but-set-variable]
struct v4l2_ctrl *ctrl;
^~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Provide support for the ADV7481 and ADV7482.
The driver is modelled with 4 subdevices to allow simultaneous streaming
from the AFE (Analog front end) and HDMI inputs though two CSI TX
entities.
The HDMI entity is linked to the TXA CSI bus, whilst the AFE is linked
to the TXB CSI bus.
The driver is based on a prototype by Koji Matsuoka in the Renesas BSP,
and an earlier rework by Niklas Söderlund.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Provides single source pad with up to 2592x1944 pixels at 10-bit raw
bayer format over MIPI CSI2 two lanes at 840Mbps/lane.
The driver supports following features:
- up to 30fps at 5M pixels
- manual exposure
- digital/analog gain
- V-blank/H-blank
- test pattern
- media controller
- runtime pm
[mchehab@s-opensource.com: fix a trivial merge conflict at Makefile]
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate const arrays on the stack but instead make them static.
Makes the object code smaller and saves nearly 550 bytes.
Before:
text data bss dec hex filename
3638 752 0 4390 1126 smiapp-quirk.o
After:
text data bss dec hex filename
2802 1040 0 3842 f02 smiapp-quirk.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add suport for standard integer menu V4L2_CID_LINK_FREQ control.
The CSI2 link frequency value is specific for each sensor mode so the
sensor mode structure is extended to add this. The control is made
read-only and its value is updated when the sensor mode is changed -
on set_format.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add suport for standard V4L2_CID_PIXEL_RATE control. The pixel clock
frequency value is specific for each sensor mode so the sensor mode
structure is extended to add this. The control is read-only and its
value is updated when the sensor mode is changed - on set_format.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Set media entity function to MEDIA_ENT_F_CAM_SENSOR.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If endpoint has an invalid configuration, ignore it instead of happily
proceeding to use it nonetheless. Ignoring such an endpoint is better than
failing since there could be multiple endpoints, only some of which are
bad.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If regulator returns -EPROBE_DEFER, we need to return it too, so that
omap3isp will be re-probed when regulator is ready.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CSI-2 PHY power management is only needed for major version 15 of the ISP.
Additionally, set the CCP2 PHY for previous ISP versions as well.
These changes are necessary for CCP2 support.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The omap3isp driver extracts the CSI-2 lane configuration from the V4L2
fwnode endpoint but misses the number of lanes itself. Get this information
and use it in PHY configuration.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CSI-2 phy driver did initialise mutexes in its init function but there
was no corresponding cleanup function destroying them. Fix that. Also
clean up ISP module initialisation a little.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check that we do have a valid port in an endpoint, return an error if not.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for CCP2 connected SMIA sensors as found
on the Nokia N900.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CCP2 and CSI-1, are older single data lane serial busses.
[mchehab@s-opensource.com: don't use spaces for identation]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Just obtain it. It'll actually get used soon with CSI-1/CCP2.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The function to parse CSI2 bus parameters was called
v4l2_fwnode_endpoint_parse_csi_bus(), rename it as
v4l2_fwnode_endpoint_parse_csi2_bus() in anticipation of CSI1/CCP2
support.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If an encoder stop command is issued after the output queue has already
stopped streaming, the qsequence counter has been reset to 0. Always
wake up the capture queue if the output queue is not streaming.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Explicitly set MPEG-4 encoder class register instead of relying on the
default value of 0.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This fixes visual artifacts in the first macroblock row of encoded
MPEG-4 video output caused by 8 additional lines of luma data leaking
into the chroma planes of the internal reference framebuffers: the
buffer size is rounded up to a multiple of 16x16 macroblock size, same
as for the h.264 encoder.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Set the field of destination buffers properly.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CodaDx6 only accepts GOP sizes up to 60 frames, but CODA960 can handle
up to 99 frames. If we disable automatic I frame generation altogether
by setting GOP size to 0, we can let an application produce arbitrarily
large I frame intervals using the V4L2_CID_MPEG_VIDEO_FORCE_KEY_FRAME
control.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This smatch warning:
coda/coda-common.c:706 coda_s_fmt() warn: missing break? reassigning 'ctx->tiled_map_type'
can be silenced by moving the ctx->tiled_map_type assignment into the
breakout condition. That way the field is not reassigned when falling
through to the next switch statement.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CODA7541 supports H.264 BP level 3/3.1 and MPEG-4 SP level 5/6.
CODA960 supports H.264 BP level 4.0 and MPEG-4 SP level 5/6.
Implement the necessary profile and level controls to let userspace know
this.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix potential NULL pointer dereference in the error path of memory
allocation failure.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate the gain tables on the stack but make them static const.
Makes the object code smaller:
Before:
text data bss dec hex filename
7801 1408 0 9209 23f9 drivers/media/tuners/fc0012.o
8483 936 0 9419 24cb drivers/media/tuners/fc0013.o
After:
text data bss dec hex filename
7696 1464 0 9160 23c8 drivers/media/tuners/fc0012.o
8362 1024 0 9386 24aa drivers/media/tuners/fc0013.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate const array saa7128_regs_ntsc on the stack but insteaed make
it static. Makes the object code smaller and saves nearly 840 bytes
Before:
text data bss dec hex filename
9218 360 0 9578 256a solo6x10-tw28.o
After:
text data bss dec hex filename
8237 504 0 8741 2225 solo6x10-tw28.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Andrey Utkin <andrey_utkin@fastmail.com>
Signed-off-by: Ismael Luceno <ismael@iodev.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When CONFIG_V4L2 is built as a loadable module, the new video mux driver
fails to link as built-in code:
drivers/media/platform/video-mux.o: In function `video_mux_remove':
video-mux.c:(.text+0x24): undefined reference to `v4l2_async_unregister_subdev'
drivers/media/platform/video-mux.o: In function `video_mux_probe':
video-mux.c:(.text+0x800): undefined reference to `v4l2_subdev_init'
video-mux.c:(.text+0xa10): undefined reference to `v4l2_async_register_subdev'
This makes it use the same Kconfig dependency as all the other users of
the VIDEO_V4L2_SUBDEV_API symbol.
Fixes: 68803ad452 ("[media] platform: add video-multiplexer subdevice driver")
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove unnecessary static on local variable t_params.
Such variable is initialized before being used,
on every execution path throughout the function.
The static has no benefit and, removing it reduces
the code size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see the difference in the code size. Also,
there is a significant difference in the bss segment. This log is the
output of the size command, before and after the code change:
before:
text data bss dec hex filename
23314 3640 832 27786 6c8a drivers/media/tuners/tuner-simple.o
after:
text data bss dec hex filename
23257 3552 768 27577 6bb9 drivers/media/tuners/tuner-simple.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Trivial fix to spelling mistake in v4l2_dbg debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Trivial fix to spelling mistake in v4l2_info message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
dma_buf_ops are not supposed to change at runtime. All functions
working with dma_buf_ops provided by <linux/dma-buf.h> work with
const dma_buf_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
5238 112 4 5354 14ea drivers/media/v4l2-core/videobuf2-dma-sg.o
File size After adding 'const':
text data bss dec hex filename
5358 0 4 5362 14f2 drivers/media/v4l2-core/videobuf2-dma-sg.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
dma_buf_ops are not supposed to change at runtime. All functions
working with dma_buf_ops provided by <linux/dma-buf.h> work with
const dma_buf_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
3171 192 0 3363 d23 drivers/media/v4l2-core/videobuf2-vmalloc.o
File size After adding 'const':
text data bss dec hex filename
3291 80 0 3371 d2b drivers/media/v4l2-core/videobuf2-vmalloc.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
dma_buf_ops are not supposed to change at runtime. All functions
working with dma_buf_ops provided by <linux/dma-buf.h> work with
const dma_buf_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6035 272 0 6307 18a3 drivers/media/v4l2-core/videobuf2-dma-contig.o
File size After adding 'const':
text data bss dec hex filename
6155 160 0 6315 18ab drivers/media/v4l2-core/videobuf2-dma-contig.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Declare v4l2_file_operations structure as const as it is only stored
in the fops field of video_device structure. This field is of type
const, so declare v4l2_file_operations structures with similar properties
as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Declare v4l2_file_operations structures as const as they are only stored
in the fops field of video_device structures. This field is of type
const, so declare v4l2_file_operations structures with similar properties
as const.
Cross compiled bfin_capture.o for blackfin arch. vpbe_display.o file did
not cross compile for arm. Could not find any architecture matching the
configuraion symbol for fsl-viu.c file.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC adapter name used by the pulse8-cec and rainshadow-cec USB device drivers
was a fixed string, but it should be unique if you connect multiple of these devices
to the same computer.
Use dev_name(&serio->dev) instead, which make it unique again.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Especially the '0.10' version number is confusing since CEC_ADAP_G_CAPS
returns a completely different version number.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some hardware does more than one attempt. So when it calls
cec_transmit_done when an error occurred it will e.g. use an error count
of 2 instead of 1.
The framework always assumed a single attempt, but now it is smarter
and will sum the counters to detect how many attempts were made.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for CEC hardware that relies on low-level pin polling or
GPIO interrupts.
One example is the Allwinner SoC. But any GPIO-based CEC implementation can
use this as well.
A GPIO implementation is very suitable as well for debugging: it can use
interrupts to detect state changes and report it. Userspace can then verify
if the bus traffic is correct. This also makes error injection possible.
The disadvantage is that it is hard to get the timings right since linux
isn't a hard realtime system.
In general on an idle system it works quite well, but under load the timer
will miss its mark every so often.
The debugfs file /sys/kernel/debug/cec/cecX/status gives some statistics
with respect to the timer overruns.
When the adapter is unconfigured and the low-level driver supports
interrupts, then the interrupt will be used to detect changes. This should
be quite accurate. But when the adapter is configured a hrtimer has to be
used.
The hrtimer implements a state machine where for each state the code will
read the bus or drive the bus and go on to the next state. It will re-arm
the timer with a delay based on the next state.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for the new MONITOR_PIN mode.
Add the cec_pin_event function that the CEC pin code will call to queue pin
change events.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Event handling was always fairly simplistic since there were only
two events. With the addition of pin events this needed to be redesigned.
The state_change and lost_msgs events are now core events with the
guarantee that the last state is always available. The new pin events
are a queue of events (up to 64 for each event) and the oldest event
will be dropped if the application cannot keep up. Lost events are
marked with a new event flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is needed for CEC adapters that allocate resources that have
to be freed before the cec_adapter is deleted.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently the transmit_(attempt_)done and received_msg functions set
the timestamp themselves. For the upcoming low-level pin API we need
to pass this as an argument instead. So make _ts variants that allow
the caller to specify the timestamp.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Kernel logging messes up the upcoming low-level CEC monitoring support
which is very time-sensitive. So change the debug level of this message
but keep a counter that is shown in the debugfs status log.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The transmit code would increase the sequence number first thing, even though
CEC_TRANSMIT would return an error due to a malformatted cec_msg struct later
on.
While valid behavior, this had the disadvantage of producing holes in the
sequence list that made debugging harder.
Only increase the sequence number when the whole message is validated.
When debugging (i.e. with cec-ctl -M) the sequence numbering is now nicely
increasing by 1 per message.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC version, vendor ID and OSD name were not cleared when clearing the
current set of logical addresses. This was unexpected and somewhat confusing,
so reset all these fields to their default values. Also document this since
the documentation wasn't quite clear either.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove the soc_camera dependencies and move the diver to i2c
Lost features, fortunately not used or not critical on test platform:
- soc_camera power on/off callback - replaced with clock enable/disable
only, no support for platform provided regulators nor power callback,
- soc_camera sense request - replaced with arbitrarily selected default
master clock rate and pixel clock limit, no support for platform
requested values,
- soc_camera board flags - no support for platform requested mbus config
tweaks.
Tested on Amstrad Delta with now out of tree but still locally
maintained omap1_camera host driver.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The vimc platform drivers define a platform device ID table but these
are not set to the .id_table field in the platform driver structure.
So the platform device ID table is only used to fill the aliases in
the module but are not used for matching (works because the platform
subsystem fallbacks to the driver's name if no .id_table is set).
But this also means that the platform device ID table isn't used if
the driver is built-in, which leads to the following build warning:
This causes the following build warnings when the driver is built-in:
drivers/media/platform/vimc//vimc-capture.c:528:40: warning: ‘vimc_cap_driver_ids’ defined but not used [-Wunused-const-variable=]
static const struct platform_device_id vimc_cap_driver_ids[] = {
^~~~~~~~~~~~~~~~~~~
drivers/media/platform/vimc//vimc-debayer.c:588:40: warning: ‘vimc_deb_driver_ids’ defined but not used [-Wunused-const-variable=]
static const struct platform_device_id vimc_deb_driver_ids[] = {
^~~~~~~~~~~~~~~~~~~
drivers/media/platform/vimc//vimc-scaler.c:442:40: warning: ‘vimc_sca_driver_ids’ defined but not used [-Wunused-const-variable=]
static const struct platform_device_id vimc_sca_driver_ids[] = {
^~~~~~~~~~~~~~~~~~~
drivers/media/platform/vimc//vimc-sensor.c:376:40: warning: ‘vimc_sen_driver_ids’ defined but not used [-Wunused-const-variable=]
static const struct platform_device_id vimc_sen_driver_ids[] = {
^~~~~~~~~~~~~~~~~~~
Reported-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Suggested-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Get rid of those two warnings:
drivers/media/platform/davinci/vpif_capture.c: In function 'vpif_remove':
drivers/media/platform/davinci/vpif_capture.c:1722:21: warning: variable 'common' set but not used [-Wunused-but-set-variable]
struct common_obj *common;
^~~~~~
drivers/media/platform/davinci/vpif_display.c: In function 'vpif_remove':
drivers/media/platform/davinci/vpif_display.c:1342:21: warning: variable 'common' set but not used [-Wunused-but-set-variable]
struct common_obj *common;
^~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZapWhAAoJEHm+PkMAQRiGKb0IAJM6b7SbWaw69Og7+qiFB+zZ
xp29iXqbE9fPISC6a5BRQV1ONjeDM6opGixGHqGC8Hla6k2IYz25VDNoF8wd0MXN
cz/Ih20vd3C5afxXGe5cTT8lsPAlV0mWXxForlu6j8jPeL62FPfq6RhEkw7AcrYL
yfYy3k3qSdOrrvBdII0WAAUi46UfIs+we9BQgbsMbkHOiqV2K0MOrzKE84Xbgepq
RAy2xg6P4b4+hTx8xTrYc1MXwpnqjRc0oJ08gdmiwW3AOOU7LxYFn7zDkLPWi9Rr
g4x6r4YhBTGxT4wNvovLIiqd9QFs//dMCuPWYwEtTICG48umIqqq24beQ0mvCdg=
=08Ic
-----END PGP SIGNATURE-----
Merge tag 'v4.13-rc1' into patchwork
Linux v4.13-rc1
* tag 'v4.13-rc1': (11136 commits)
Linux v4.13-rc1
random: reorder READ_ONCE() in get_random_uXX
random: suppress spammy warnings about unseeded randomness
replace incorrect strscpy use in FORTIFY_SOURCE
kmod: throttle kmod thread limit
kmod: add test driver to stress test the module loader
MAINTAINERS: give kmod some maintainer love
xtensa: use generic fb.h
fault-inject: add /proc/<pid>/fail-nth
fault-inject: simplify access check for fail-nth
fault-inject: make fail-nth read/write interface symmetric
fault-inject: parse as natural 1-based value for fail-nth write interface
fault-inject: automatically detect the number base for fail-nth write interface
kernel/watchdog.c: use better pr_fmt prefix
MAINTAINERS: move the befs tree to kernel.org
lib/atomic64_test.c: add a test that atomic64_inc_not_zero() returns an int
mm: fix overflow check in expand_upwards()
ubifs: Set double hash cookie also for RENAME_EXCHANGE
ubifs: Massage assert in ubifs_xattr_set() wrt. init_xattrs
ubifs: Don't leak kernel memory to the MTD
...
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZYseIAAoJEAx081l5xIa+85kP/0zKzKKVzZXSXG2TAGb5jNfk
Ex+TELG8tWk9KBxA7lEE5c0WEsnP79cNoXZLQu8wlUzO8+kwQK5Bz0zgNUkpSuo1
RthwdsxBQX1++UxB+HoSG+dOa7hkKVqlgQR3z9qyhsBXzetkJV0DoYcpMV0A1EWd
6Jzt+AvCShVkcW+21LqHPlc5EIVewrDMoA3oU6aYCLhyAOUTVvvQB2ML8YApH7TM
JrSrzCFHTrQEBbGUrZQhzR0sZzZzk9byntb/I/mdVbHeCyIHiL8sC4PfWSOyyazm
GkPnA8G3aFAY9haBRz9jG/VBr1yVb0mCBjkWQ1lGfIAOCDDSc+d7PDXdG+i4AewK
jZheXlrDIdGgmJLy4W3rdEqJvdf7UQHZOs8594OL19l4+FxCTrol1JSHSMeavCvr
8bUNil9Jb/ONU/wmp+q55U0k4TCTyerUA7gKnuaJAwBvd4n78/PKmQnbrWinDyJc
GQXp6zESk9bKt5DXSnVZuVf4POTzpuAsQkkfX1V2y145EHTQYfS3jLENWqEjyZUy
QtKCHZvRkJfGaFU4Pr+vBo9Iu1GlA5OiOv08QadldTT4OxUI0T6yaLDobHCQfKPE
sc3wCuCM+/dAnqoKDcGC4hAmF8zDdO0kw65P2m7uC6T9Jm1G35CioKbzo+fzUhuL
fg5TBpbp2Wwe2oPA5iBm
=2S5N
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.13' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm, I think I've got one later
driver pull for mediatek SoC driver, I'm undecided on if it needs to
go to you yet.
Otherwise summary below:
Core drm:
- Atomic add driver private objects
- Deprecate preclose hook in modern drivers
- MST bandwidth tracking
- Use kvmalloc in more places
- Add mode_valid hook for crtc/encoder/bridge
- Reduce sync_file construction time
- Documentation updates
- New DRM synchronisation object support
New drivers:
- pl111 - pl111 CLCD display controller
Panel:
- Innolux P079ZCA panel driver
- Add NL12880B20-05, NL192108AC18-02D, P320HVN03 panels
- panel-samsung-s6e3ha2: Add s6e3hf2 panel support
i915:
- SKL+ watermark fixes
- G4x/G33 reset improvements
- DP AUX backlight improvements
- Buffer based GuC/host communication
- New getparam for (sub)slice infomation
- Cannonlake and Coffeelake initial patches
- Execbuf optimisations
radeon/amdgpu:
- Lots of Vega10 bug fixes
- Preliminary raven support
- KIQ support for compute rings
- MEC queue management rework
- DCE6 Audio support
- SR-IOV improvements
- Better radeon/amdgpu selection support
nouveau:
- HDMI stereoscopic support
- Display code rework for >= GM20x GPUs
msm:
- GEM rework for fine-grained locking
- Per-process pagetable work
- HDMI fixes for Snapdragon 820.
vc4:
- Remove 256MB CMA limit from vc4
- Add out-fence support
- Add support for cygnus
- Get/set tiling ioctls support
- Add T-format tiling support for scanout
zte:
- add VGA support.
etnaviv:
- Thermal throttle support for newer GPUs
- Restore userspace buffer cache performance
- dma-buf sync fix
stm:
- add stm32f429 display support
exynos:
- Rework vblank handling
- Fixup sw-trigger code
sun4i:
- V3s display engine support
- HDMI support for older SoCs
- Preliminary work on dual-pipeline SoCs.
rcar-du:
- VSP work
imx-drm:
- Remove counter load enable from PRE
- Double read/write reduction flag support
tegra:
- Documentation for the host1x and drm driver.
- Lots of staging ioctl fixes due to grate project work.
omapdrm:
- dma-buf fence support
- TILER rotation fixes"
* tag 'drm-for-v4.13' of git://people.freedesktop.org/~airlied/linux: (1270 commits)
drm: Remove unused drm_file parameter to drm_syncobj_replace_fence()
drm/amd/powerplay: fix bug fail to remove sysfs when rmmod amdgpu.
amdgpu: Set cik/si_support to 1 by default if radeon isn't built
drm/amdgpu/gfx9: fix driver reload with KIQ
drm/amdgpu/gfx8: fix driver reload with KIQ
drm/amdgpu: Don't call amd_powerplay_destroy() if we don't have powerplay
drm/ttm: Fix use-after-free in ttm_bo_clean_mm
drm/amd/amdgpu: move get memory type function from early init to sw init
drm/amdgpu/cgs: always set reference clock in mode_info
drm/amdgpu: fix vblank_time when displays are off
drm/amd/powerplay: power value format change for Vega10
drm/amdgpu/gfx9: support the amdgpu.disable_cu option
drm/amd/powerplay: change PPSMC_MSG_GetCurrPkgPwr for Vega10
drm/amdgpu: Make amdgpu_cs_parser_init static (v2)
drm/amdgpu/cs: fix a typo in a comment
drm/amdgpu: Fix the exported always on CU bitmap
drm/amdgpu/gfx9: gfx_v9_0_enable_gfx_static_mg_power_gating() can be static
drm/amdgpu/psp: upper_32_bits/lower_32_bits for address setup
drm/amd/powerplay/cz: print message if smc message fails
drm/amdgpu: fix typo in amdgpu_debugfs_test_ib_init
...
-----BEGIN PGP SIGNATURE-----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=RtxO
-----END PGP SIGNATURE-----
Merge tag 'media/v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- addition of fwnode support at V4L2 core
- addition of a few more SDR formats
- new imx driver to support i.MX6 cameras
- new driver for Qualcon venus codecs
- new I2C sensor drivers: dw9714, max2175, ov13858, ov5640
- new CEC driver: stm32-cec
- some improvements to DVB frontend documentation and a few fixups
- several driver improvements and fixups
* tag 'media/v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (361 commits)
[media] media: entity: Catch unbalanced media_pipeline_stop calls
[media] media/uapi/v4l: clarify cropcap/crop/selection behavior
[media] v4l2-ioctl/exynos: fix G/S_SELECTION's type handling
[media] vimc: sen: Declare vimc_sen_video_ops as static
[media] vimc: sca: Add scaler
[media] vimc: deb: Add debayer filter
[media] vimc: Subdevices as modules
[media] vimc: cap: Support several image formats
[media] vimc: sen: Support several image formats
[media] vimc: common: Add vimc_colorimetry_clamp
[media] vimc: common: Add vimc_link_validate
[media] vimc: common: Add vimc_pipeline_s_stream helper
[media] vimc: common: Add vimc_ent_sd_* helper
[media] vimc: Move common code from the core
[media] vimc: sen: Integrate the tpg on the sensor
[media] media: i2c: ov772x: Force use of SCCB protocol
[media] dvb uapi docs: enums are passed by value, not reference
[media] dvb: don't use 'time_t' in event ioctl
[media] media: venus: enable building with COMPILE_TEST
[media] af9013: refactor power control
...
This development cycle resulted in a fair amount of changes in both
core and driver sides. The most significant change in ALSA core is
about PCM. Also the support of of-graph card and the new DAPM widget
for DSP are noteworthy changes in ASoC core. And there're lots of
small changes splat over the tree, as you can see in diffstat.
Below are a few highlights:
ALSA core:
- Removal of set_fs() hackery from PCM core stuff, and the code
reorganization / optimization thereafter
- Improved support of PCM ack ops, and a new ABI for improved
control/status mmap handling
- Lots of constifications in various codes
ASoC core:
- The support of of-graph card, which may work as a better generic
device for a replacement of simple-card
- New widget types intended mainly for use with DSPs
ASoC drivers:
- New drivers for Allwinner V3s SoCs
- Ensonic ES8316 codec support
- More Intel SKL and KBL works
- More device support for Intel SST Atom (mostly for cheap tablets and
2-in-1 devices)
- Support for Rockchip PDM controllers
- Support for STM32 I2S and S/PDIF controllers
- Support for ZTE AUD96P22 codecs
HD-audio:
- Support of new Realtek codecs (ALC215/ALC285/ALC289), more quirks
for HP and Dell machines
- A few more fixes for i915 component binding
Note that of-graph change may bring the conflicts with a later pull
request of devicetree, as currently found in linux-next.
-----BEGIN PGP SIGNATURE-----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=PUEh
-----END PGP SIGNATURE-----
Merge tag 'sound-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This development cycle resulted in a fair amount of changes in both
core and driver sides. The most significant change in ALSA core is
about PCM. Also the support of of-graph card and the new DAPM widget
for DSP are noteworthy changes in ASoC core. And there're lots of
small changes splat over the tree, as you can see in diffstat.
Below are a few highlights:
ALSA core:
- Removal of set_fs() hackery from PCM core stuff, and the code
reorganization / optimization thereafter
- Improved support of PCM ack ops, and a new ABI for improved
control/status mmap handling
- Lots of constifications in various codes
ASoC core:
- The support of of-graph card, which may work as a better generic
device for a replacement of simple-card
- New widget types intended mainly for use with DSPs
ASoC drivers:
- New drivers for Allwinner V3s SoCs
- Ensonic ES8316 codec support
- More Intel SKL and KBL works
- More device support for Intel SST Atom (mostly for cheap tablets
and 2-in-1 devices)
- Support for Rockchip PDM controllers
- Support for STM32 I2S and S/PDIF controllers
- Support for ZTE AUD96P22 codecs
HD-audio:
- Support of new Realtek codecs (ALC215/ALC285/ALC289), more quirks
for HP and Dell machines
- A few more fixes for i915 component binding"
* tag 'sound-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (418 commits)
ALSA: hda - Fix unbalance of i915 module refcount
ASoC: Intel: Skylake: Remove driver debugfs exit
ASoC: Intel: Skylake: explicitly add the headers sst-dsp.h
ALSA: hda/realtek - Remove GPIO_MASK
ALSA: hda/realtek - Fix typo of pincfg for Dell quirk
ALSA: pcm: add a documentation for tracepoints
ALSA: atmel: ac97c: fix error return code in atmel_ac97c_probe()
ALSA: x86: fix error return code in hdmi_lpe_audio_probe()
ASoC: Intel: Skylake: Add support to read firmware registers
ASoC: Intel: Skylake: Add sram address to sst_addr structure
ASoC: Intel: Skylake: Debugfs facility to dump module config
ASoC: Intel: Skylake: Add debugfs support
ASoC: fix semicolon.cocci warnings
ASoC: rt5645: Add quirk override by module option
ASoC: rsnd: make arrays path and cmd_case static const
ASoC: audio-graph-card: add widgets and routing for external amplifier support
ASoC: audio-graph-card: update bindings for amplifier support
ASoC: rt5665: calibration should be done before jack detection
ASoC: rsnd: constify dev_pm_ops structures.
ASoC: nau8825: change crosstalk-bypass property to bool type
...
The big news with this release is the of-graph card, this provides a
replacement for simple-card that is much more flexibile and scalable,
allowing many more systems to use a generic sound card than was possible
before:
- The of-graph card, finally merged after a long and dedicated effort
by Morimoto-san.
- New widget types intended mainly for use with DSPs.
- New drivers for Allwinner V3s SoCs, Ensonic ES8316, several classes
of x86 machine, Rockchip PDM controllers, STM32 I2S and S/PDIF
controllers and ZTE AUD96P22 CODECs.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAllaa7wTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0MhRB/0cIuUi/SmMSGz7cNKdDDArdpxHUV0U
dJb6qqhXCKeDQcx/34b1m+BnZpeT9au4Nt8HxOlLRbumcnuesYqfeBeZvuJhsC4I
q3e8e+idQlOp3+WM+snUXhWM4P/UsA9H4BaV1jvYSQW/C9WhfuLxsOraRiebLH7u
WJkmfeVjpzHHWzfDtpWJLHVroRLLMbOaz0e0Pw8/R1dfof0u27zKknqHOUcwRg0N
4+IWvKn3p59VE6eM6QUmruMZZCCfn2Hv5RygWf3LaHVlhA28BZi0dyMMSSSzVG6o
Im1Wm5z0dmmTfQKdNDU3PPBEKG6amTqF+2uuXOsq1I7vuiT+akHZbgWW
=F5BP
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.13
The big news with this release is the of-graph card, this provides a
replacement for simple-card that is much more flexibile and scalable,
allowing many more systems to use a generic sound card than was possible
before:
- The of-graph card, finally merged after a long and dedicated effort
by Morimoto-san.
- New widget types intended mainly for use with DSPs.
- New drivers for Allwinner V3s SoCs, Ensonic ES8316, several classes
of x86 machine, Rockchip PDM controllers, STM32 I2S and S/PDIF
controllers and ZTE AUD96P22 CODECs.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZUGOmAAoJEHm+PkMAQRiGhX8H/3fIhingPD01MBf98U0xGrJo
yIXmhu6nFs7TM0lDVDcHsKgqLQIT69ll7PrSZrMkc1RGUIPINoCuJVuJqDre0kfB
of5TX2KegqSx8h1vOWjGBCBjdYfPGyMdf9icf6KsGc/SlIdhN6WA99kglAjJA0Ve
qPTNagF0ntUNg1lsXffxyfcHqFpyqw/Z/C4ie/byFsn9iJ1VG9mNlTWSud09vhuM
3tvHzTUVAIWWuRrrgrvgqQpnwL+q5BfSDsXScMjBau0EK3RGGqG8EN6Kbkfa7VQ6
aBoeboQjUijSJnVwvySdQ11MChTIOwZdfrNPra/1HD3WJNsSu4BIRt5JcAKcOhc=
=qmSg
-----END PGP SIGNATURE-----
Backmerge tag 'v4.12-rc7' into drm-next
Linux 4.12-rc7
Needed at least rc6 for drm-misc-next-fixes, may as well go to rc7
The buffer mode was already implemented in this driver, but it did not work
as expected. This has been fixed now, but it is still deactivated and can
be activated by removing a comment at the begin of the file.
Original code change by Ralph Metzler, modified by Jasmin Jessich and
Daniel Scheller to match Kernel code style.
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some lower level drivers may work better when sending blocks of data
instead byte per byte. For this we need new function pointers in the
dvb_ca_en50221 protocol structure (read_data, write_data) and the protocol
needs to execute them, if they are defined.
Block data transmission is done in all states except LINKINIT.
Original code change by Ralph Metzler, modified by Jasmin Jessich and
Daniel Scheller to match Kernel code style.
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some CAMs do a really slow initialization, which requires a longer timeout
for the first response.
Original code change by Ralph Metzler, modified by Jasmin Jessich to match
Kernel code style.
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In case of a linkinit failure change to state UNINITIALISED to re-init
the CAM.
Original code change by Ralph Metzler, modified by Jasmin Jessich to match
Kernel code style.
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The stv0367 driver provide a lot of status on its state machine.
Change the logic to provide more information about frontend locking
status. Also, while any detailed status isn't available, provide a more
complete FE_STATUS for DVB-T.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Provide QAM/DVB-C signal strength in decibel scale. Values returned from
stv0367cab_get_rf_lvl() are good but need to be multiplied as they're in
1dBm precision.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since the other statistics are read when fe_status conditions are TRUE,
change the ucblocks readout logic to match this aswell.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While there's a test at the SNR calculus to avoid division by
zero, it will still follow the path that would do the division.
So, add a missing break there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add signal-to-noise-ratio as provided by the demodulator in decibel scale.
QAM/DVB-C needs some intlog calculation to have usable dB values, OFDM/
DVB-T values from the demod look alright already and are provided as-is.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the demod driver puts the demod into sleep or shutdown state and it's
status is then polled e.g. via "dvb-fe-tool -m", i2c errors are printed
to the kernel log. If the last delsys was DVB-T/T2:
cxd2841er: i2c wr failed=-5 addr=6c reg=00 len=1
cxd2841er: i2c rd failed=-5 addr=6c reg=26
and if it was DVB-C:
cxd2841er: i2c wr failed=-5 addr=6c reg=00 len=1
cxd2841er: i2c rd failed=-5 addr=6c reg=49
This happens when read_status unconditionally calls into the
read_signal_strength() function which triggers the read_agc_gain_*()
functions, where these registered are polled.
This isn't a critical thing since when the demod is active again, no more
such errors are logged, however this might make users suspecting defects.
Fix this by requiring STATE_ACTIVE_* in priv->state. If it isn't in any
active state, additionally set the strength scale to NOT_AVAILABLE.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Value assigned to variable _type_ at line 678 is overwritten at line 688
before it can be used. This makes such variable assignment useless.
Remove this variable assignment and fix some coding style issues.
Addresses-Coverity-ID: 1226968
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The read_snr() functions currently do some magic to return relative scale
values when called. Split out register readouts into separate functions
so the functionality can be reused in some other way.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds the basics to stv0367ddb_read_status() to be able to properly
provide signal statistics in DVBv5 format. Also adds UCB readout and
provides those values. Also, don't return -EINVAL in ddb_read_status()
if active_demod_state indicates no delivery system.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use dev_dbg() in conjunction with the %*ph format macro to print the vmon
status debug, thus hiding continuous hexdumping from default log levels.
Also, change the attach success log line from error to info severity.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The semaphore 'i2c_switch_mutex' is used as a simple mutex, so
it should be written as one. Semaphores are going away in the future.
Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The semaphore 'stream_mutex' is used as a simple mutex, so
it should be written as one. Also moving the mutex_[lock/unlock]
to the caller as it is anyway locked at the beginning of the
callee thus avoiding repetition.
Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The semaphore 'cmd_mutex' is used as a simple mutex, so
it should be written as one. Also, replace down with
mutex_destroy to ensure sane state when ngene_stop is
called.
Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As such macro will check if the expression is true, it may fall through, as
warned:
In file included from ./include/uapi/linux/stddef.h:1:0,
from ./include/linux/stddef.h:4,
from ./include/uapi/linux/posix_types.h:4,
from ./include/uapi/linux/types.h:13,
from ./include/linux/types.h:5,
from ./drivers/media/dvb-core/dvb_frontend.h:35,
from drivers/media/tuners/fc0011.h:4,
from drivers/media/tuners/fc0011.c:20:
drivers/media/tuners/fc0011.c: In function 'fc0011_set_params':
./include/linux/compiler.h:179:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:109:2: note: in expansion of macro 'unlikely'
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/media/tuners/fc0011.c:344:3: note: in expansion of macro 'WARN_ON'
WARN_ON(1);
^~~~~~~
drivers/media/tuners/fc0011.c:345:2: note: here
case 0:
^~~~
In file included from ./include/uapi/linux/stddef.h:1:0,
from ./include/linux/stddef.h:4,
from ./include/uapi/linux/posix_types.h:4,
from ./include/uapi/linux/types.h:13,
from ./include/linux/types.h:5,
from ./include/linux/list.h:4,
from ./include/linux/module.h:9,
from drivers/media/pci/tw5864/tw5864-video.c:17:
drivers/media/pci/tw5864/tw5864-video.c: In function 'tw5864_fmt_vid_cap':
./include/linux/compiler.h:179:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:68:2: note: in expansion of macro 'unlikely'
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/media/pci/tw5864/tw5864-video.c:547:3: note: in expansion of macro 'WARN_ON_ONCE'
WARN_ON_ONCE(1);
^~~~~~~~~~~~
drivers/media/pci/tw5864/tw5864-video.c:548:2: note: here
case STD_NTSC:
^~~~
On both cases, it means an error, so, let's return an error
code, to make gcc happy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
DRX_S9TOS16 and DRX_S24TODRXFREQ are simply not used. Furthermore,
sign_extend32() should be used for sign extension. (Also, the comment
describing DRX_S24TODRXFREQ was wrong). So remove these macros.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dmaengine driver for sDMA now have support for interleaved transfer.
This trasnfer type was open coded with the legacy omap-dma API, but now
we can move it to dmaengine.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While committing a change on em28xx, I got a warning of a
typo there. So, fix it on em28xx and on two other media drivers
with the same typo.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While testing support for Terratec H6 rev. 2, it was noticed
that reading from eeprom there causes a timeout error.
Apparently, this is due to the need of properly setting GPIOs.
In any case, the driver doesn't really require eeprom reading
to succeed, as this is currently used only for debug.
So, Ignore such errors.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mostly this adds some unlocks to error paths. But, if you see where
there were "break;" statements before, I changed those paths to return
error codes instead of returning success.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch mostly adds unlocks to error paths. But one additional small
change is that I made the first "break;" a "goto unlock;" which means
that now we return failure instead of success on that path.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Values assigned to variables Fmax and Fmin at lines 2740 and 2741 are
overwritten at lines 2754 and 2755 before they can be used. This makes
such variable assignments useless.
Addresses-Coverity-ID: 1226952
Addresses-Coverity-ID: 1226953
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Side effect: KERN_DEBUG messages aren't written to the kernel log anymore.
This also improves the tda18212_ping reporting a bit so users know that if
pinging wasn't successful, bad things will happen.
Since in module_init_ddbridge() there's no dev yet, pr_info is used
instead.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Reported by smatch:
drivers/media/pci/ddbridge/ddbridge-core.c:1246 input_tasklet() warn: this loop depends on readl() succeeding
drivers/media/pci/ddbridge/ddbridge-core.c:1768 flashio() warn: this loop depends on readl() succeeding
drivers/media/pci/ddbridge/ddbridge-core.c:1788 flashio() warn: this loop depends on readl() succeeding
Fix this by introducing safe_ddbreadl() which will wrap ddbreadl and checks
for all bits set in the return which indicates failure, and return 0 in
that case. Usable as drop-in-replacement in all affected while loops w/o
having to change the logic.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
I would have liked the the picture run timeout error handler to be renamed to
something a bit more descriptive in the original commit fb2be08f8c ("[media]
coda: first step at error recovery").
Somehow v1 [1] was merged instead of v2 [2].
[1] https://patchwork.kernel.org/patch/9663965/
[2] https://patchwork.kernel.org/patch/9774239/
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current pre-decrement is incorrect and should be replaced
with a post-decrement. Consider the case where the very first
clk_prepare_enable fails when i is 0; in this case the error
clean up will decrement the unsigned int which wraps to the
largest unsigned int value causing an array out of bounds read
on core->clks[i].
Detected by CoverityScan, CID#1446590 ("Out-of-bounds read")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check return value from call to core->write(), so in case of
error print error message, jump to goto label fail and eventually
return.
Addresses-Coverity-ID: 1226943
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Back in April I created a patch to address a false-positive warning:
drivers/media/usb/rainshadow-cec/rainshadow-cec.c: In function 'rain_irq_work_handler':
drivers/media/usb/rainshadow-cec/rainshadow-cec.c:171:31: error: 'data' may be used uninitialized in this function [-Werror=maybe-uninitialized]
My patch was totally wrong and introduced a real bug, and Colin Ian King thankfully
noticed it now and fixed my mistake. Unfortunately, fixing the actual uninitialized
data in this case brought back the original bogus warning.
This is a new version of the patch, which simplifies the code to the point where
gcc notices the behavior is correct.
Fixes: ca33784ba4 ("[media] rainshadow-cec: ensure exit_loop is intialized")
Fixes: ea6a69defd ("[media] rainshadow-cec: avoid -Wmaybe-uninitialized warning")
Cc: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit 680d87c0a9 ("[media] tuner-core: use pr_foo, instead of
internal printk macros") removed the use of PREFIX, remove the #define
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert STK_<LEVEL> to pr_<level> to use the typical kernel logging.
Add a define for pr_fmt. No change in logging output.
Miscellanea:
o Remove now unused PREFIX and STK_<LEVEL> macros
o Realign arguments
o Use pr_<level>_ratelimited
o Add a few missing newlines to formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This fixes a smatch warning:
drivers/media/platform/coda/coda-bit.c:415 coda_alloc_framebuffers()
error: we previously assumed 'ctx->codec' could be null (see line 396)
coda_alloc_framebuffers() is called from coda_start_encoding() and
__coda_start_decoding(). Both dereference ctx->codec before calling
coda_alloc_framebuffers() in lines 935 and 1649, so ctx->codec can not
be NULL.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This one got applied twice, causing a build error with clang:
drivers/media/i2c/et8ek8/et8ek8_driver.c:1499:1: error: redefinition of '__mod_of__et8ek8_of_table_device_table'
Fixes: 9ae05fd1e7 ("[media] et8ek8: Export OF device ID as module aliases")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Seven single characters (line breaks) should be put into a sequence.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drivers must not perform unbalanced calls to stop the entity pipeline,
however if they do they will fault in the core media code, as the
entity->pipe will be set as NULL. We handle this gracefully in the core
with a WARN for the developer.
Replace the erroneous check on zero streaming counts, with a check on
NULL pipe elements instead, as this is the symptom of unbalanced
media_pipeline_stop calls.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pincharts@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The type field in struct v4l2_selection is supposed to never use the
_MPLANE variants. E.g. if the driver supports V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE,
then userspace should still pass V4L2_BUF_TYPE_VIDEO_CAPTURE.
The reasons for this are lost in the mists of time, but it is really
annoying. In addition, the exynos drivers didn't follow this rule and
instead expected the _MPLANE type.
To fix that code is added to the v4l2 core that maps the _MPLANE buffer
types to their regular equivalents before calling the driver.
Effectively this allows for userspace to use either _MPLANE or the regular
buffer type. This keeps backwards compatibility while making things easier
for userspace.
Since drivers now never see the _MPLANE buffer types the exynos drivers
had to be adapted as well.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implement scaler and integrated with the core
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implement the debayer filter and integrate it with the core
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Change the core structure for adding subdevices in the topology.
Instead of calling the specific create function for each subdevice,
inject a child platform_device with the driver's name.
Each type of node in the topology (sensor, capture, debayer, scaler)
will register a platform_driver with the corresponding name through the
component subsystem.
Implementing a new subdevice type doesn't require vimc-core to be altered.
This facilitates future implementation of dynamic entities, where
hotpluging an entity in the topology is just a matter of
registering/unregistering a platform_device in the system.
It also facilitates other implementations of different nodes without
touching the core code and remove the need of a header file for each
type of node.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Allow user space to change the image format as the frame size, the
pixel format, colorspace, quantization, field YCbCr encoding
and the transfer function
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Allow user space to change the image format as the frame size, the
media bus pixel format, colorspace, quantization, field YCbCr encoding
and the transfer function
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Colorimetry value will always be checked in the same way. Adding a
helper macro for that
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
All links will be checked in the same way. Adding a helper function for
that
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move the vimc_cap_pipeline_s_stream from the vimc-cap.c to vimc-common.c
as this core will be reused by other subdevices to activate the stream
in their directly connected nodes
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As all the subdevices in the topology will be initialized in the same
way, to avoid code repetition the vimc_ent_sd_{register, unregister}
helper functions were created
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove helper functions from vimc-core and add it in vimc-common to
clean up the core.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Initialize the test pattern generator on the sensor
Generate a colored bar image instead of a grey one
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit e789029761 ("i2c: sh_mobile: don't send a stop condition by
default inside transfers") makes the i2c_sh_mobile I2C-adapter emit a
stop/start sequence between messages in a single transfer only when
explicitly requested with I2C_M_STOP.
This breaks the ov772x driver in the SH4 Migo-R board as the Omnivision
sensor uses the I2C-like SCCB protocol that doesn't support repeated
starts:
i2c-sh_mobile i2c-sh_mobile.0: Transfer request timed out
ov772x 0-0021: Product ID error 92:92
Fix it by marking the client as SCCB, forcing the emission of a
stop/start sequence between all messages.
As I2C_M_STOP requires the I2C adapter to support protocol mangling,
ensure that the I2C_FUNC_PROTOCOL_MANGLING functionality is available.
Tested on SH4 Migo-R board, with OV772x now successfully probing
soc-camera-pdrv soc-camera-pdrv.0: Probing soc-camera-pdrv.0
ov772x 0-0021: ov7725 Product ID 77:21 Manufacturer ID 7f:a2
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We want all media drivers to build with COMPILE_TEST, as the
Coverity instance we use on Kernel works only for x86. Also,
our test workflow relies on it, in order to identify git
bisect breakages.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Move power-up and power-down functionality to init/sleep ops and
get rid of old function.
Fixes and simplifies power-up functionality slightly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We need to wait 2nd demod power-up before download firmware. Move
that wait to more correct location.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Removed register writes are already chip defaults, are not required,
are set later or belong to AF9015 USB interface.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
