This hack (affecting the non-PCIe models only) was introduced in 2004
to deal with link negotiation failures in 1GBit mode. Based on a
comment in the r8169 vendor driver I assume the issue affects RTL8169sb
in combination with particular 1GBit switch models.
Resetting the PHY every 10s and hoping that one fine day we will make
it to establish the link seems to be very hacky to me. I'd say:
If 1GBit doesn't work reliably in a users environment then the user
should remove 1GBit from the advertised modes, e.g. by using
ethtool -s <if> advertise <10/100 modes>
If the issue affects one chip version only and that with most link
partners, then we could also think of removing 1GBit from the
advertised modes for this chip version in the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru says:
====================
qed*: Fix series.
The patch series addresses few issues in the qed* drivers.
Please consider applying it to 'net' branch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When ptp clock is not available for a PF (e.g., higher PFs in NPAR mode),
get-tsinfo() callback should return the software timestamp capabilities
instead of returning the error.
Fixes: 4c55215c ("qede: Add driver support for PTP")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the correct size value while copying chassis/port id values.
Fixes: 6ad8c632e ("qed: Add support for query/config dcbx.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, driver sets the eswitch mode incorrectly as VEB (virtual
Ethernet bridging).
Need to set VEB eswitch mode only when sriov is enabled, and it should be
to set NONE by default. The patch incorporates this change.
Fixes: 0fefbfbaa ("qed*: Management firmware - notifications and defaults")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory size is limited in the kdump kernel environment. Allocation of more
msix-vectors (or queues) consumes few tens of MBs of memory, which might
lead to the kdump kernel failure.
This patch adds changes to limit the number of MSI-X vectors in kdump
kernel to minimum required value (i.e., 2 per engine).
Fixes: fe56b9e6a ("qed: Add module with basic common support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After we change the ipvlan mode from l3 to l2, or vice versa, we only
reset IFF_NOARP flag, but don't flush the ARP table cache, which will
cause eth->h_dest to be equal to eth->h_source in ipvlan_xmit_mode_l2().
Then the message will not come out of host.
Here is the reproducer on local host:
ip link set eth1 up
ip addr add 192.168.1.1/24 dev eth1
ip link add link eth1 ipvlan1 type ipvlan mode l3
ip netns add net1
ip link set ipvlan1 netns net1
ip netns exec net1 ip link set ipvlan1 up
ip netns exec net1 ip addr add 192.168.2.1/24 dev ipvlan1
ip route add 192.168.2.0/24 via 192.168.1.2
ping 192.168.2.2 -c 2
ip netns exec net1 ip link set ipvlan1 type ipvlan mode l2
ping 192.168.2.2 -c 2
Add the same configuration on remote host. After we set the mode to l2,
we could find that the src/dst MAC addresses are the same on eth1:
21:26:06.648565 00:b7:13:ad:d3:05 > 00:b7:13:ad:d3:05, ethertype IPv4 (0x0800), length 98: (tos 0x0, ttl 64, id 58356, offset 0, flags [DF], proto ICMP (1), length 84)
192.168.2.1 > 192.168.2.2: ICMP echo request, id 22686, seq 1, length 64
Fix this by calling dev_change_flags(), which will call netdevice notifier
with flag change info.
v2:
a) As pointed out by Wang Cong, check return value for dev_change_flags() when
change dev flags.
b) As suggested by Stefano and Sabrina, move flags setting before l3mdev_ops.
So we don't need to redo ipvlan_{, un}register_nf_hook() again in err path.
Reported-by: Jianlin Shi <jishi@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'mask' argument to crypto_alloc_shash() uses the CRYPTO_ALG_* flags,
not 'gfp_t'. So don't pass GFP_KERNEL to it.
Fixes: bf355b8d2c ("ipv6: sr: add core files for SR HMAC support")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if sa_idx is equal to NSIM_IPSEC_MAX_SA_COUNT then
an out-of-bounds read on ipsec->sa will occur. Fix the
incorrect bounds check by using >= rather than >.
Detected by CoverityScan, CID#1470226 ("Out-of-bounds-read")
Fixes: 7699353da8 ("netdevsim: add ipsec offload testing")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the addition of GRO for ESP, gro_receive can consume the skb and
return -EINPROGRESS. In that case, the lower layer GRO handler cannot
touch the skb anymore.
Commit 5f114163f2 ("net: Add a skb_gro_flush_final helper.") converted
some of the gro_receive handlers that can lead to ESP's gro_receive so
that they wouldn't access the skb when -EINPROGRESS is returned, but
missed other spots, mainly in tunneling protocols.
This patch finishes the conversion to using skb_gro_flush_final(), and
adds a new helper, skb_gro_flush_final_remcsum(), used in VXLAN and
GUE.
Fixes: 5f114163f2 ("net: Add a skb_gro_flush_final helper.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amritha Nambiar says:
====================
Symmetric queue selection using XPS for Rx queues
This patch series implements support for Tx queue selection based on
Rx queue(s) map. This is done by configuring Rx queue(s) map per Tx-queue
using sysfs attribute. If the user configuration for Rx queues does
not apply, then the Tx queue selection falls back to XPS using CPUs and
finally to hashing.
XPS is refactored to support Tx queue selection based on either the
CPUs map or the Rx-queues map. The config option CONFIG_XPS needs to be
enabled. By default no receive queues are configured for the Tx queue.
- /sys/class/net/<dev>/queues/tx-*/xps_rxqs
A set of receive queues can be mapped to a set of transmit queues (many:many),
although the common use case is a 1:1 mapping. This will enable sending
packets on the same Tx-Rx queue association as this is useful for busy polling
multi-threaded workloads where it is not possible to pin the threads to
a CPU. This is a rework of Sridhar's patch for symmetric queueing via
socket option:
https://www.spinics.net/lists/netdev/msg453106.html
Testing Hints:
Kernel: Linux 4.17.0-rc7+
Interface:
driver: ixgbe
version: 5.1.0-k
firmware-version: 0x00015e0b
Configuration:
ethtool -L $iface combined 16
ethtool -C $iface rx-usecs 1000
sysctl net.core.busy_poll=1000
ATR disabled:
ethtool -K $iface ntuple on
Workload:
Modified memcached that changes the thread selection policy to be based
on the incoming rx-queue of a connection using SO_INCOMING_NAPI_ID socket
option. The default is round-robin.
Default: No rxqs_map configured
Symmetric queues: Enable rxqs_map for all queues 1:1 mapped to Tx queue
System:
Architecture: x86_64
CPU(s): 72
Model name: Intel(R) Xeon(R) CPU E5-2699 v3 @ 2.30GHz
16 threads 400K requests/sec
=============================
-------------------------------------------------------------------------------
Default Symmetric queues
-------------------------------------------------------------------------------
RTT min/avg/max 4/51/2215 2/30/5163
(usec)
intr/sec 26655 18606
contextswitch/sec 5145 4044
insn per cycle 0.43 0.72
cache-misses 6.919 4.310
(% of all cache refs)
L1-dcache-load- 4.49 3.29
-misses
(% of all L1-dcache hits)
LLC-load-misses 13.26 8.96
(% of all LL-cache hits)
-------------------------------------------------------------------------------
32 threads 400K requests/sec
=============================
-------------------------------------------------------------------------------
Default Symmetric queues
-------------------------------------------------------------------------------
RTT min/avg/max 10/112/5562 9/46/4637
(usec)
intr/sec 30456 27666
contextswitch/sec 7552 5133
insn per cycle 0.41 0.49
cache-misses 9.357 2.769
(% of all cache refs)
L1-dcache-load- 4.09 3.98
-misses
(% of all L1-dcache hits)
LLC-load-misses 12.96 3.96
(% of all LL-cache hits)
-------------------------------------------------------------------------------
16 threads 800K requests/sec
=============================
-------------------------------------------------------------------------------
Default Symmetric queues
-------------------------------------------------------------------------------
RTT min/avg/max 5/151/4989 9/69/2611
(usec)
intr/sec 35686 22907
contextswitch/sec 25522 12281
insn per cycle 0.67 0.74
cache-misses 8.652 6.38
(% of all cache refs)
L1-dcache-load- 3.19 2.86
-misses
(% of all L1-dcache hits)
LLC-load-misses 16.53 11.99
(% of all LL-cache hits)
-------------------------------------------------------------------------------
32 threads 800K requests/sec
=============================
-------------------------------------------------------------------------------
Default Symmetric queues
-------------------------------------------------------------------------------
RTT min/avg/max 6/163/6152 8/88/4209
(usec)
intr/sec 47079 26548
contextswitch/sec 42190 39168
insn per cycle 0.45 0.54
cache-misses 8.798 4.668
(% of all cache refs)
L1-dcache-load- 6.55 6.29
-misses
(% of all L1-dcache hits)
LLC-load-misses 13.91 10.44
(% of all LL-cache hits)
-------------------------------------------------------------------------------
v6:
- Changed the names of some functions to begin with net_if.
- Cleaned up sk_tx_queue_set/sk_rx_queue_set functions.
- Added sk_rx_queue_clear to make it consistent with tx_queue_mapping
initialization.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend transmit queue sysfs attribute to configure Rx queue(s) map
per Tx queue. By default no receive queues are configured for the
Tx queue.
- /sys/class/net/eth0/queues/tx-*/xps_rxqs
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to pick Tx queue based on the Rx queue(s) map
configuration set by the admin through the sysfs attribute
for each Tx queue. If the user configuration for receive queue(s) map
does not apply, then the Tx queue selection falls back to CPU(s) map
based selection and finally to hashing.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new field to sock_common 'skc_rx_queue_mapping'
which holds the receive queue number for the connection. The Rx queue
is marked in tcp_finish_connect() to allow a client app to do
SO_INCOMING_NAPI_ID after a connect() call to get the right queue
association for a socket. Rx queue is also marked in tcp_conn_request()
to allow syn-ack to go on the right tx-queue associated with
the queue on which syn is received.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change 'skc_tx_queue_mapping' field in sock_common structure from
'int' to 'unsigned short' type with ~0 indicating unset and
other positive queue values being set. This will accommodate adding
a new 'unsigned short' field in sock_common in the next patch for
rx_queue_mapping.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use static_key for XPS maps to reduce the cost of extra map checks,
similar to how it is used for RPS and RFS. This includes static_key
'xps_needed' for XPS and another for 'xps_rxqs_needed' for XPS using
Rx queues map.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor XPS code to support Tx queue selection based on
CPU(s) map or Rx queue(s) map.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=KWL7
-----END PGP SIGNATURE-----
Merge tag 'for-4.18-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"We have a few regression fixes for qgroup rescan status tracking and
the vm_fault_t conversion that mixed up the error values"
* tag 'for-4.18-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix mount failure when qgroup rescan is in progress
Btrfs: fix regression in btrfs_page_mkwrite() from vm_fault_t conversion
btrfs: quota: Set rescan progress to (u64)-1 if we hit last leaf
Pull vfs fix from Al Viro:
"Followup to procfs-seq_file series this window"
This fixes a memory leak by making sure that proc seq files release any
private data on close. The 'proc_seq_open' has to be properly paired
with 'proc_seq_release' that releases the extra private data.
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
proc: add proc_seq_release
Here are a few small staging and IIO driver fixes for 4.18-rc3.
Nothing major or big, all just fixes for reported problems since
4.18-rc1. All of these have been in linux-next this week with no
reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWziQ7w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynwZACgjpcPVTEiA0W02s4B/GhmVt1NMeUAnjgeLDzY
yRz6SX18lSmjHqCUXAk1
=/2QW
-----END PGP SIGNATURE-----
Merge tag 'staging-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are a few small staging and IIO driver fixes for 4.18-rc3.
Nothing major or big, all just fixes for reported problems since
4.18-rc1. All of these have been in linux-next this week with no
reported problems"
* tag 'staging-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: android: ion: Return an ERR_PTR in ion_map_kernel
staging: comedi: quatech_daqp_cs: fix no-op loop daqp_ao_insn_write()
iio: imu: inv_mpu6050: Fix probe() failure on older ACPI based machines
iio: buffer: fix the function signature to match implementation
iio: mma8452: Fix ignoring MMA8452_INT_DRDY
iio: tsl2x7x/tsl2772: avoid potential division by zero
iio: pressure: bmp280: fix relative humidity unit
Here are 5 fixes for the tty core and some serial drivers.
The tty core one fix some security and other issues reported by the
syzbot that I have taken too long in responding to (sorry Tetsuo!). The
8350 serial driver fix resolves an issue of devices that used to work
properly stopping working as they shouldn't have been added to a
blacklist.
All of these have been in linux-next for a few days with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWziSHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym5LACg0xI1fC7LAKrLSLKglU/H4Wsv6b0AoNIkfbWi
wxAZZKscwFVKNpv6gN9n
=YgAj
-----END PGP SIGNATURE-----
Merge tag 'tty-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are five fixes for the tty core and some serial drivers.
The tty core ones fix some security and other issues reported by the
syzbot that I have taken too long in responding to (sorry Tetsuo!).
The 8350 serial driver fix resolves an issue of devices that used to
work properly stopping working as they shouldn't have been added to a
blacklist.
All of these have been in linux-next for a few days with no reported
issues"
* tag 'tty-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vt: prevent leaking uninitialized data to userspace via /dev/vcs*
serdev: fix memleak on module unload
serial: 8250_pci: Remove stalled entries in blacklist
n_tty: Access echo_* variables carefully.
n_tty: Fix stall at n_tty_receive_char_special().
Here is a number of USB gadget and other driver fixes for 4.18-rc3.
There's a bunch of them here, most of them being gadget driver and xhci
host controller fixes for reported issues (as normal), but there are
also some new device ids, and some fixes for the typec code.
There is an acpi core patch in here that was acked by the acpi
maintainer as it is needed for the typec fixes in order to properly
solve a problem in that driver.
All of these have been in linux-next this week with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWziS+Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn8QQCfU8PnLo+uPoV+DU7Nm1486mHTP4YAoLU3Q0nE
oRmnzA3TnxytluWgbC7M
=H8MG
-----END PGP SIGNATURE-----
Merge tag 'usb-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a number of USB gadget and other driver fixes for 4.18-rc3.
There's a bunch of them here, most of them being gadget driver and
xhci host controller fixes for reported issues (as normal), but there
are also some new device ids, and some fixes for the typec code.
There is an acpi core patch in here that was acked by the acpi
maintainer as it is needed for the typec fixes in order to properly
solve a problem in that driver.
All of these have been in linux-next this week with no reported
issues"
* tag 'usb-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: chipidea: host: fix disconnection detect issue
usb: typec: tcpm: fix logbuffer index is wrong if _tcpm_log is re-entered
typec: tcpm: Fix a msecs vs jiffies bug
NFC: pn533: Fix wrong GFP flag usage
usb: cdc_acm: Add quirk for Uniden UBC125 scanner
staging/typec: fix tcpci_rt1711h build errors
usb: typec: ucsi: Fix for incorrect status data issue
usb: typec: ucsi: acpi: Workaround for cache mode issue
acpi: Add helper for deactivating memory region
usb: xhci: increase CRS timeout value
usb: xhci: tegra: fix runtime PM error handling
usb: xhci: remove the code build warning
xhci: Fix kernel oops in trace_xhci_free_virt_device
xhci: Fix perceived dead host due to runtime suspend race with event handler
dwc2: gadget: Fix ISOC IN DDMA PID bitfield value calculation
usb: gadget: dwc2: fix memory leak in gadget_init()
usb: gadget: composite: fix delayed_status race condition when set_interface
usb: dwc2: fix isoc split in transfer with no data
usb: dwc2: alloc dma aligned buffer for isoc split in
usb: dwc2: fix the incorrect bitmaps for the ports of multi_tt hub
...
If SACK is not enabled and the first cumulative ACK after the RTO
retransmission covers more than the retransmitted skb, a spurious
FRTO undo will trigger (assuming FRTO is enabled for that RTO).
The reason is that any non-retransmitted segment acknowledged will
set FLAG_ORIG_SACK_ACKED in tcp_clean_rtx_queue even if there is
no indication that it would have been delivered for real (the
scoreboard is not kept with TCPCB_SACKED_ACKED bits in the non-SACK
case so the check for that bit won't help like it does with SACK).
Having FLAG_ORIG_SACK_ACKED set results in the spurious FRTO undo
in tcp_process_loss.
We need to use more strict condition for non-SACK case and check
that none of the cumulatively ACKed segments were retransmitted
to prove that progress is due to original transmissions. Only then
keep FLAG_ORIG_SACK_ACKED set, allowing FRTO undo to proceed in
non-SACK case.
(FLAG_ORIG_SACK_ACKED is planned to be renamed to FLAG_ORIG_PROGRESS
to better indicate its purpose but to keep this change minimal, it
will be done in another patch).
Besides burstiness and congestion control violations, this problem
can result in RTO loop: When the loss recovery is prematurely
undoed, only new data will be transmitted (if available) and
the next retransmission can occur only after a new RTO which in case
of multiple losses (that are not for consecutive packets) requires
one RTO per loss to recover.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Tested-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally in patch e6d20c55a4 ("openrisc: entry: Fix delay slot
detection") I fixed delay slot detection, but only for QEMU. We missed
that hardware delay slot detection using delay slot exception flag (DSX)
was still broken. This was because QEMU set the DSX flag in both
pre-exception supervision register (ESR) and supervision register (SR)
register, but on real hardware the DSX flag is only set on the SR
register during exceptions.
Fix this by carrying the DSX flag into the SR register during exception.
We also update the DSX flag read locations to read the value from the SR
register not the pt_regs SR register which represents ESR. The ESR
should never have the DSX flag set.
In the process I updated/removed a few comments to match the current
state. Including removing a comment saying that the DSX detection logic
was inefficient and needed to be rewritten.
I have tested this on QEMU with a patch ensuring it matches the hardware
specification.
Link: https://lists.gnu.org/archive/html/qemu-devel/2018-07/msg00000.html
Fixes: e6d20c55a4 ("openrisc: entry: Fix delay slot detection")
Signed-off-by: Stafford Horne <shorne@gmail.com>
Daniel Borkmann says:
====================
pull-request: bpf 2018-07-01
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) A bpf_fib_lookup() helper fix to change the API before freeze to
return an encoding of the FIB lookup result and return the nexthop
device index in the params struct (instead of device index as return
code that we had before), from David.
2) Various BPF JIT fixes to address syzkaller fallout, that is, do not
reject progs when set_memory_*() fails since it could still be RO.
Also arm32 JIT was not using bpf_jit_binary_lock_ro() API which was
an issue, and a memory leak in s390 JIT found during review, from
Daniel.
3) Multiple fixes for sockmap/hash to address most of the syzkaller
triggered bugs. Usage with IPv6 was crashing, a GPF in bpf_tcp_close(),
a missing sock_map_release() routine to hook up to callbacks, and a
fix for an omitted bucket lock in sock_close(), from John.
4) Two bpftool fixes to remove duplicated error message on program load,
and another one to close the libbpf object after program load. One
additional fix for nfp driver's BPF offload to avoid stopping offload
completely if replace of program failed, from Jakub.
5) Couple of BPF selftest fixes that bail out in some of the test
scripts if the user does not have the right privileges, from Jeffrin.
6) Fixes in test_bpf for s390 when CONFIG_BPF_JIT_ALWAYS_ON is set
where we need to set the flag that some of the test cases are expected
to fail, from Kleber.
7) Fix to detangle BPF_LIRC_MODE2 dependency from CONFIG_CGROUP_BPF
since it has no relation to it and lirc2 users often have configs
without cgroups enabled and thus would not be able to use it, from Sean.
8) Fix a selftest failure in sockmap by removing a useless setrlimit()
call that would set a too low limit where at the same time we are
already including bpf_rlimit.h that does the job, from Yonghong.
9) Fix BPF selftest config with missing missing NET_SCHED, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend says:
====================
This addresses two syzbot issues that lead to identifying (by Eric and
Wei) a class of bugs where we don't correctly check for IPv4/v6
sockets and their associated state. The second issue was a locking
omission in sockhash.
The first patch addresses IPv6 socks and fixing an error where
sockhash would overwrite the prot pointer with IPv4 prot. To fix
this build similar solution to TLS ULP. Although we continue to
allow socks in all states not just ESTABLISH in this patch set
because as Martin points out there should be no issue with this
on the sockmap ULP because we don't use the ctx in this code. Once
multiple ULPs coexist we may need to revisit this. However we
can do this in *next trees.
The other issue syzbot found that the tcp_close() handler missed
locking the hash bucket lock which could result in corrupting the
sockhash bucket list if delete and close ran at the same time.
And also the smap_list_remove() routine was not working correctly
at all. This was not caught in my testing because in general my
tests (to date at least lets add some more robust selftest in
bpf-next) do things in the "expected" order, create map, add socks,
delete socks, then tear down maps. The tests we have that do the
ops out of this order where only working on single maps not multi-
maps so we never saw the issue. Thanks syzbot. The fix is to
restructure the tcp_close() lock handling. And fix the obvious
bug in smap_list_remove().
Finally, during review I noticed the release handler was omitted
from the upstream code (patch 4) due to an incorrect merge conflict
fix when I ported the code to latest bpf-next before submitting.
This would leave references to the map around if the user never
closes the map.
v3: rework patches, dropping ESTABLISH check and adding rcu
annotation along with the smap_list_remove fix
v4: missed one more case where maps was being accessed without
the sk_callback_lock, spoted by Martin as well.
v5: changed to use a specific lock for maps and reduced callback
lock so that it is only used to gaurd sk callbacks. I think
this makes the logic a bit cleaner and avoids confusion
ovoer what each lock is doing.
Also big thanks to Martin for thorough review he caught at least
one case where I missed a rcu_call().
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add map_release_uref pointer to hashmap ops. This was dropped when
original sockhash code was ported into bpf-next before initial
commit.
Fixes: 8111038444 ("bpf: sockmap, add hash map support")
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
First the sk_callback_lock() was being used to protect both the
sock callback hooks and the psock->maps list. This got overly
convoluted after the addition of sockhash (in sockmap it made
some sense because masp and callbacks were tightly coupled) so
lets split out a specific lock for maps and only use the callback
lock for its intended purpose. This fixes a couple cases where
we missed using maps lock when it was in fact needed. Also this
makes it easier to follow the code because now we can put the
locking closer to the actual code its serializing.
Next, in sock_hash_delete_elem() the pattern was as follows,
sock_hash_delete_elem()
[...]
spin_lock(bucket_lock)
l = lookup_elem_raw()
if (l)
hlist_del_rcu()
write_lock(sk_callback_lock)
.... destroy psock ...
write_unlock(sk_callback_lock)
spin_unlock(bucket_lock)
The ordering is necessary because we only know the {p}sock after
dereferencing the hash table which we can't do unless we have the
bucket lock held. Once we have the bucket lock and the psock element
it is deleted from the hashmap to ensure any other path doing a lookup
will fail. Finally, the refcnt is decremented and if zero the psock
is destroyed.
In parallel with the above (or free'ing the map) a tcp close event
may trigger tcp_close(). Which at the moment omits the bucket lock
altogether (oops!) where the flow looks like this,
bpf_tcp_close()
[...]
write_lock(sk_callback_lock)
for each psock->maps // list of maps this sock is part of
hlist_del_rcu(ref_hash_node);
.... destroy psock ...
write_unlock(sk_callback_lock)
Obviously, and demonstrated by syzbot, this is broken because
we can have multiple threads deleting entries via hlist_del_rcu().
To fix this we might be tempted to wrap the hlist operation in a
bucket lock but that would create a lock inversion problem. In
summary to follow locking rules the psocks maps list needs the
sk_callback_lock (after this patch maps_lock) but we need the bucket
lock to do the hlist_del_rcu.
To resolve the lock inversion problem pop the head of the maps list
repeatedly and remove the reference until no more are left. If a
delete happens in parallel from the BPF API that is OK as well because
it will do a similar action, lookup the lock in the map/hash, delete
it from the map/hash, and dec the refcnt. We check for this case
before doing a destroy on the psock to ensure we don't have two
threads tearing down a psock. The new logic is as follows,
bpf_tcp_close()
e = psock_map_pop(psock->maps) // done with map lock
bucket_lock() // lock hash list bucket
l = lookup_elem_raw(head, hash, key, key_size);
if (l) {
//only get here if elmnt was not already removed
hlist_del_rcu()
... destroy psock...
}
bucket_unlock()
And finally for all the above to work add missing locking around map
operations per above. Then add RCU annotations and use
rcu_dereference/rcu_assign_pointer to manage values relying on RCU so
that the object is not free'd from sock_hash_free() while it is being
referenced in bpf_tcp_close().
Reported-by: syzbot+0ce137753c78f7b6acc1@syzkaller.appspotmail.com
Fixes: 8111038444 ("bpf: sockmap, add hash map support")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
If a hashmap is free'd with open socks it removes the reference to
the hash entry from the psock. If that is the last reference to the
psock then it will also be free'd by the reference counting logic.
However the current logic that removes the hash reference from the
list of references is broken. In smap_list_remove() we first check
if the sockmap entry matches and then check if the hashmap entry
matches. But, the sockmap entry sill always match because its NULL in
this case which causes the first entry to be removed from the list.
If this is always the "right" entry (because the user adds/removes
entries in order) then everything is OK but otherwise a subsequent
bpf_tcp_close() may reference a free'd object.
To fix this create two list handlers one for sockmap and one for
sockhash.
Reported-by: syzbot+0ce137753c78f7b6acc1@syzkaller.appspotmail.com
Fixes: 8111038444 ("bpf: sockmap, add hash map support")
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This fixes a crash where we assign tcp_prot to IPv6 sockets instead
of tcpv6_prot.
Previously we overwrote the sk->prot field with tcp_prot even in the
AF_INET6 case. This patch ensures the correct tcp_prot and tcpv6_prot
are used.
Tested with 'netserver -6' and 'netperf -H [IPv6]' as well as
'netperf -H [IPv4]'. The ESTABLISHED check resolves the previously
crashing case here.
Fixes: 174a79ff95 ("bpf: sockmap with sk redirect support")
Reported-by: syzbot+5c063698bdbfac19f363@syzkaller.appspotmail.com
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski says:
====================
Set of random updates to bpftool and libbpf. I'm preparing for
extending bpftool prog load, but there is a good number of
improvements that can be made before bpf -> bpf-next merge
helping to keep the later patch set to a manageable size as well.
First patch is a bpftool build speed improvement. Next missing
program types are added to libbpf program type detection by section
name. The ability to load programs from '.text' section is restored
when ELF file doesn't contain any pseudo calls.
In bpftool I remove my Author comments as unnecessary sign of vanity.
Last but not least missing option is added to bash completions and
processing of options in bash completions is improved.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Remove options (in getopt() sense, i.e. starting with a dash like
-n or --NAME) while parsing arguments for bash completions. This
allows us to refer to position-dependent parameters better, and
complete options at any point.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
--bpffs is not suggested by bash completions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Drop my author comments, those are from the early days of
bpftool and make little sense in tree, where we have quite
a few people contributing and git to attribute the work.
While at it bump some copyrights.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Make bpf_program__next() skip over '.text' section if object file
has pseudo calls. The '.text' section is hardly a program in that
case, it's more of a storage for code of functions other than main.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
libbpf used to be able to load programs from the default section
called '.text'. It's not very common to leave sections unnamed,
but if it happens libbpf will fail to load the programs reporting
-EINVAL from the kernel. The -EINVAL comes from bpf_obj_name_cpy()
because since 48cca7e44f ("libbpf: add support for bpf_call")
libbpf does not resolve program names for programs in '.text',
defaulting to '.text'. '.text', however, does not pass the
(isalnum(*src) || *src == '_') check in bpf_obj_name_cpy().
With few extra lines of code we can limit the pseudo call
assumptions only to objects which actually contain code relocations.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Users of bpf_object__open()/bpf_object__load() APIs may want to
load the programs and maps onto a device for offload. Allow
setting ifindex on those sub-objects.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Specify default section names for BPF_PROG_TYPE_LIRC_MODE2
and BPF_PROG_TYPE_LWT_SEG6LOCAL, these are the only two
missing right now.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Commit 4bfe3bd3cc ("tools/bpftool: use version from the kernel
source tree") added version to bpftool. The version used is
equal to the kernel version and obtained by running make kernelversion
against kernel source tree. Version is then communicated
to the sources with a command line define set in CFLAGS.
Use a simply expanded variable for the version, otherwise the
recursive make will run every time CFLAGS are used.
This brings the single-job compilation time for me from almost
16 sec down to less than 4 sec.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pull parisc fixes and cleanups from Helge Deller:
"Nothing exiting in this patchset, just
- small cleanups of header files
- default to 4 CPUs when building a SMP kernel
- mark 16kB and 64kB page sizes broken
- addition of the new io_pgetevents syscall"
* 'parisc-4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Build kernel without -ffunction-sections
parisc: Reduce debug output in unwind code
parisc: Wire up io_pgetevents syscall
parisc: Default to 4 SMP CPUs
parisc: Convert printk(KERN_LEVEL) to pr_lvl()
parisc: Mark 16kB and 64kB page sizes BROKEN
parisc: Drop struct sigaction from not exported header file
A smaller batch for the end of the week (let's see if I can keep the
weekly cadence going for once).
All medium-grade fixes here, nothing worrisome:
- Fixes for some fairly old bugs around SD card write-protect detection
and GPIO interrupt assignments on Davinci.
- Wifi module suspend fix for Hikey.
- Minor DT tweaks to fix inaccuracies for Amlogic platforms, on of
which solves booting with third-party u-boot.
-----BEGIN PGP SIGNATURE-----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=55JJ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A smaller batch for the end of the week (let's see if I can keep the
weekly cadence going for once).
All medium-grade fixes here, nothing worrisome:
- Fixes for some fairly old bugs around SD card write-protect
detection and GPIO interrupt assignments on Davinci.
- Wifi module suspend fix for Hikey.
- Minor DT tweaks to fix inaccuracies for Amlogic platforms, one
of which solves booting with third-party u-boot"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: dts: hikey960: Define wl1837 power capabilities
arm64: dts: hikey: Define wl1835 power capabilities
ARM64: dts: meson-gxl: fix Mali GPU compatible string
ARM64: dts: meson-axg: fix ethernet stability issue
ARM64: dts: meson-gx: fix ATF reserved memory region
ARM64: dts: meson-gxl-s905x-p212: Add phy-supply for usb0
ARM64: dts: meson: fix register ranges for SD/eMMC
ARM64: dts: meson: disable sd-uhs modes on the libretech-cc
ARM: dts: da850: Fix interrups property for gpio
ARM: davinci: board-da850-evm: fix WP pin polarity for MMC/SD
- introduce __diag_* macros and suppress -Wattribute-alias warnings from GCC 8
- fix stack protector test script for x86_64
- fix line number handling in Kconfig
- document that '#' starts a comment in Kconfig
- handle P_SYMBOL property in dump debugging of Kconfig
- correct help message of LD_DEAD_CODE_DATA_ELIMINATION
- fix occasional segmentation faults in Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=oABr
-----END PGP SIGNATURE-----
Merge tag 'kbuild-fixes-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- introduce __diag_* macros and suppress -Wattribute-alias warnings
from GCC 8
- fix stack protector test script for x86_64
- fix line number handling in Kconfig
- document that '#' starts a comment in Kconfig
- handle P_SYMBOL property in dump debugging of Kconfig
- correct help message of LD_DEAD_CODE_DATA_ELIMINATION
- fix occasional segmentation faults in Kconfig
* tag 'kbuild-fixes-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: loop boundary condition fix
kbuild: reword help of LD_DEAD_CODE_DATA_ELIMINATION
kconfig: handle P_SYMBOL in print_symbol()
kconfig: document Kconfig source file comments
kconfig: fix line numbers for if-entries in menu tree
stack-protector: Fix test with 32-bit userland and CONFIG_64BIT=y
powerpc: Remove -Wattribute-alias pragmas
disable -Wattribute-alias warning for SYSCALL_DEFINEx()
kbuild: add macro for controlling warnings to linux/compiler.h
Pull x86 fixes from Ingo Molnar:
"The biggest diffstat comes from self-test updates, plus there's entry
code fixes, 5-level paging related fixes, console debug output fixes,
and misc fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Clean up the printk()s in show_fault_oops()
x86/mm: Drop unneeded __always_inline for p4d page table helpers
x86/efi: Fix efi_call_phys_epilog() with CONFIG_X86_5LEVEL=y
selftests/x86/sigreturn: Do minor cleanups
selftests/x86/sigreturn/64: Fix spurious failures on AMD CPUs
x86/entry/64/compat: Fix "x86/entry/64/compat: Preserve r8-r11 in int $0x80"
x86/mm: Don't free P4D table when it is folded at runtime
x86/entry/32: Add explicit 'l' instruction suffix
x86/mm: Get rid of KERN_CONT in show_fault_oops()
Pull perf fixes from Ingo Molnar:
"Tooling fixes mostly, plus a build warning fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
perf/core: Move inline keyword at the beginning of declaration
tools/headers: Pick up latest kernel ABIs
perf tools: Fix crash caused by accessing feat_ops[HEADER_LAST_FEATURE]
perf script: Fix crash because of missing evsel->priv
perf script: Add missing output fields in a hint
perf bench: Fix numa report output code
perf stat: Remove duplicate event counting
perf alias: Rebuild alias expression string to make it comparable
perf alias: Remove trailing newline when reading sysfs files
perf tools: Fix a clang 7.0 compilation error
tools include uapi: Synchronize bpf.h with the kernel
tools include uapi: Update if_link.h to pick IFLA_{BRPORT_ISOLATED,VXLAN_TTL_INHERIT}
tools include powerpc: Update arch/powerpc/include/uapi/asm/unistd.h copy to get 'rseq' syscall
perf tools: Update x86's syscall_64.tbl, adding 'io_pgetevents' and 'rseq'
tools headers uapi: Synchronize drm/drm.h
perf intel-pt: Fix packet decoding of CYC packets
perf tests: Add valid callback for parse-events test
perf tests: Add event parsing error handling to parse events test
perf report powerpc: Fix crash if callchain is empty
perf test session topology: Fix test on s390
...
-----BEGIN PGP SIGNATURE-----
iQJIBAABCAAyFiEEcQCq365ubpQNLgrWVeRaWujKfIoFAls2gk0UHHBhdWxAcGF1
bC1tb29yZS5jb20ACgkQVeRaWujKfIqEvRAAgjtXjU7cN9Vj7GZpwgSjJKyXSruR
RDM19CRDKIo27UoxaqD92hFnmDreoysdzLi9cunDxshsUbGdHeyXvaOkY2apqpkn
msPIKO3pmoiq0Umze1/smgl6g0ruPxc+ZSslfuHLUjephogfuDGKgfTeLN60z6up
KaiVPoaSni+DZSsiFOkzUHwQFfhTRqONBx/tfPo2H1K0bP2dy9YuOCdvpZEqpc7P
8tx/uF3pYrUBuq9ufEgWt2VC0fU1uZJEI21BQqKcrXLYlmVr73pWYLXnV1NWck0A
rY5DABxbDf1sXCAIhYRJJDiM51uPltmFfntGF3sS1OKYOgyxIxf51xwgl9dXsGOA
jOFFwUuXeHJpWICTm1PQCdpA/mzLVgrPzt8ULPE6zYnP+LbBId6RSrPz6Irhswal
/wiq1mlhdAdeBf2r/tY3VXUy8dMNLjfeHLD3scx07hfFuswXCPTC6xwlyiKPsgKD
1hGCQazZZTNAcMVI4A00SpPZVGx1yU/Yu/+8vMKyV5BmT55TPcQElcQy+ZZxuX1a
711B9U7P6w7k8UwL+hVSncgwCLI1vb4MKnmrGZRH9wXiUdaKcgivaDDoeoLTtqBF
dcIP84OtigAHbJHxWXoTmuRX9KGmtgF5sUBgFv2kg8R8EgnmVKaWJxyyttRg4awo
RZXmTh2eC3p3IGw=
=fzCd
-----END PGP SIGNATURE-----
Merge tag 'selinux-pr-20180629' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull selinux fix from Paul Moore:
"One fairly straightforward patch to fix a longstanding issue where a
process could stall while accessing files in selinuxfs and block
everyone else due to a held mutex.
The patch passes all our tests and looks to apply cleanly to your
current tree"
* tag 'selinux-pr-20180629' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: move user accesses in selinuxfs out of locked regions
-----BEGIN PGP SIGNATURE-----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=0uqV
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20180629' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Small set of fixes for this series. Mostly just minor fixes, the only
oddball in here is the sg change.
The sg change came out of the stall fix for NVMe, where we added a
mempool and limited us to a single page allocation. CONFIG_SG_DEBUG
sort-of ruins that, since we'd need to account for that. That's
actually a generic problem, since lots of drivers need to allocate SG
lists. So this just removes support for CONFIG_SG_DEBUG, which I added
back in 2007 and to my knowledge it was never useful.
Anyway, outside of that, this pull contains:
- clone of request with special payload fix (Bart)
- drbd discard handling fix (Bart)
- SATA blk-mq stall fix (me)
- chunk size fix (Keith)
- double free nvme rdma fix (Sagi)"
* tag 'for-linus-20180629' of git://git.kernel.dk/linux-block:
sg: remove ->sg_magic member
drbd: Fix drbd_request_prepare() discard handling
blk-mq: don't queue more if we get a busy return
block: Fix cloning of requests with a special payload
nvme-rdma: fix possible double free of controller async event buffer
block: Fix transfer when chunk sectors exceeds max
After commit f9d4b0c1e9 ("fib_rules: move common handling of newrule
delrule msgs into fib_nl2rule"), rule_exists got replaced by rule_find
for existing rule lookup in both the add and del paths. While this
is good for the delete path, it solves a few problems but opens up
a few invalid key matches in the add path.
$ip -4 rule add table main tos 10 fwmark 1
$ip -4 rule add table main tos 10
RTNETLINK answers: File exists
The problem here is rule_find does not check if the key masks in
the new and old rule are the same and hence ends up matching a more
secific rule. Rule key masks cannot be easily compared today without
an elaborate if-else block. Its best to introduce key masks for easier
and accurate rule comparison in the future. Until then, due to fear of
regressions this patch re-introduces older loose rule_exists during add.
Also fixes both rule_exists and rule_find to cover missing attributes.
Fixes: f9d4b0c1e9 ("fib_rules: move common handling of newrule delrule msgs into fib_nl2rule")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
