Don't use _HIZ macros but also provide a val. This is more consistent
with the other macros and, thus, easier to read. Also shorter.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211119110442.4946-1-wsa+renesas@sang-engineering.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Instead of writing fixed values with undocumented bits which happen to
be set on some SoCs, better switch to read-modify-write operations
changing only bits which are documented. This is way more future-proof
as we don't know yet how these bits may be on upcoming SoCs.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211117093710.14430-1-wsa+renesas@sang-engineering.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
No need to open code regmap_update_bits().
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211117102902.20062-1-wsa+renesas@sang-engineering.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
SPI Multi I/O Bus Controller on RZ/G2L SoC is almost identical to
the RPC-IF interface found on R-Car Gen3 SoC's.
This patch adds a new compatible string for the RZ/G2L family so
that the timing values on RZ/G2L can be adjusted.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211025205631.21151-8-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
RPCIF_DIRMAP_SIZE may differ on various SoC's. Instead of using
RPCIF_DIRMAP_SIZE macro use resource size to get dirmap size
which is already part of struct rpcif.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211025205631.21151-7-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
HyperFlash devices in Renesas SoCs use 2-bytes addressing, according
to HW manual paragraph 62.3.3 (which officially describes Serial Flash
access, but seems to be applicable to HyperFlash too). And 1-byte bus
read operations to 2-bytes unaligned addresses in external address space
read mode work incorrectly (returns the other byte from the same word).
Function memcpy_fromio(), used by the driver to read data from the bus,
in ARM64 architecture (to which Renesas cores belong) uses 8-bytes
bus accesses for appropriate aligned addresses, and 1-bytes accesses
for other addresses. This results in incorrect data read from HyperFlash
in unaligned cases.
This issue can be reproduced using something like the following commands
(where mtd1 is a parition on Hyperflash storage, defined properly
in a device tree):
[Correct fragment, read from Hyperflash]
root@rcar-gen3:~# dd if=/dev/mtd1 of=/tmp/zz bs=32 count=1
root@rcar-gen3:~# hexdump -C /tmp/zz
00000000 f4 03 00 aa f5 03 01 aa f6 03 02 aa f7 03 03 aa |................|
00000010 00 00 80 d2 40 20 18 d5 00 06 81 d2 a0 18 a6 f2 |....@ ..........|
00000020
[Incorrect read of the same fragment: see the difference at offsets 8-11]
root@rcar-gen3:~# dd if=/dev/mtd1 of=/tmp/zz bs=12 count=1
root@rcar-gen3:~# hexdump -C /tmp/zz
00000000 f4 03 00 aa f5 03 01 aa 03 03 aa aa |............|
0000000c
Fix this issue by creating a local replacement of the copying function,
that performs only properly aligned bus accesses, and is used for reading
from HyperFlash.
Fixes: ca7d8b980b ("memory: add Renesas RPC-IF driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Link: https://lore.kernel.org/r/20210922184830.29147-1-andrew_gabbasov@mentor.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
This patch fixes 2 problems:
[1] The output warning logs and data loss when performing
mount/umount then remount the device with jffs2 format.
[2] The access width of SMWDR[0:1]/SMRDR[0:1] register is wrong.
This is the sample warning logs when performing mount/umount then
remount the device with jffs2 format:
jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x031c51d4:
Read 0x00034e00, calculated 0xadb272a7
The reason for issue [1] is that the writing data seems to
get messed up.
Data is only completed when the number of bytes is divisible by 4.
If you only have 3 bytes of data left to write, 1 garbage byte
is inserted after the end of the write stream.
If you only have 2 bytes of data left to write, 2 bytes of '00'
are added into the write stream.
If you only have 1 byte of data left to write, 2 bytes of '00'
are added into the write stream. 1 garbage byte is inserted after
the end of the write stream.
To solve problem [1], data must be written continuously in serial
and the write stream ends when data is out.
Following HW manual 62.2.15, access to SMWDR0 register should be
in the same size as the transfer size specified in the SPIDE[3:0]
bits in the manual mode enable setting register (SMENR).
Be sure to access from address 0.
So, in 16-bit transfer (SPIDE[3:0]=b'1100), SMWDR0 should be
accessed by 16-bit width.
Similar to SMWDR1, SMDDR0/1 registers.
In current code, SMWDR0 register is accessed by regmap_write()
that only set up to do 32-bit width.
To solve problem [2], data must be written 16-bit or 8-bit when
transferring 1-byte or 2-byte.
Fixes: ca7d8b980b ("memory: add Renesas RPC-IF driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Duc Nguyen <duc.nguyen.ub@renesas.com>
[wsa: refactored to use regmap only via reg_read/reg_write]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922091007.5516-1-wsa+renesas@sang-engineering.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The platform_get_resource_byname() can return NULL which would be
immediately dereferenced by resource_size(). Instead dereference it
after validating the resource.
Addresses-Coverity: Dereference null return value
Fixes: ca7d8b980b ("memory: add Renesas RPC-IF driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210407154357.70200-1-krzysztof.kozlowski@canonical.com
Define rpcif_enable_rpm() and rpcif_disable_rpm() as static
inline in the header instead of exporting them.
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Pavel Machek (CIP) <pavel@denx.de>
Link: https://lore.kernel.org/r/20201126191146.8753-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In the error path of rpcif_manual_xfer() the value of ret is overwritten
by value returned by reset_control_reset() function and thus returning
incorrect value to the caller.
This patch makes sure the correct value is returned to the caller of
rpcif_manual_xfer() by dropping the overwrite of ret in error path.
Also now we ignore the value returned by reset_control_reset() in the
error path and instead print a error message when it fails.
Fixes: ca7d8b980b ("memory: add Renesas RPC-IF driver")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Pavel Machek (CIP) <pavel@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201126191146.8753-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add the memory driver for Renesas RPC-IF which registers either SPI or
HyperFLash device depending on the contents of the device tree subnode.
It also provides the absract "back end" device APIs that can be used by
the "front end" SPI/MTD drivers to talk to the real hardware.
Based on the original patch by Mason Yang <masonccyang@mxic.com.tw>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Link: https://lore.kernel.org/r/9a3606ec-d4d0-c63a-4fb6-631ab38e621c@cogentembedded.com
Signed-off-by: Mark Brown <broonie@kernel.org>
