In ALSA firewire stack, some AV/C commands are supported, including
vendor's extensions. Drivers includes response parser of each command,
according to its requirements, while the parser is written with loose
fashion in two points; error check and length check. This doesn't cause
any issues such as kernel corruption, but should be improved.
This commit modifies evaluations of return value on each parsers.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now snd_rawmidi_ops is maintained as a const pointer in snd_rawmidi,
we can constify the definitions.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some identifiers are referred just by one functions. In this case, they
can be put into the function definition. This brings two merits; readers
can easily follow codes related to the identifiers, developers are free
from name conflict.
This commit moves such identifiers to each function definition.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The below models were developed with a cooperation by Yamaha and Terratec.
- Yamaha GO 44/Terratec PHASE 24 FW
- Yamaha GO 46/Terratec PHASE X24 FW
They have the same configurations, thus it's better to unify corresponding
codes.
This commit merges them to reduce the amount of maintained codes.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Once Yamaha and Terratec cooperated to develop some audio and music units
on IEEE 1394 bus. On these models, the same embedded board is used, and
similar configurations are also applied.
This commit renames file for Yamaha's configuration so that it's for both
of Yamaha and Terratec.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In former commit, drivers in ALSA firewire stack always starts IT context
before IR context. If IR context starts after packets are transmitted by
peer unit, packet discontinuity may be detected because the context starts
in the middle of packet streaming. This situation is rare because IT
context usually starts immediately. However, it's better to solve this
issue. This is suppressed with CIP_SKIP_INIT_DBC_CHECK flag.
This commit enables the same feature as CIP_SKIP_INIT_DBC_CHECK.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Windows driver for BeBoB-based models mostly wait for transmitted packets,
then transfer packets to the models. This looks for the relationship
between incoming packets and outgoing packets to synchronize the sequence
of presentation timestamp.
However, the sequence between packets of both direction has no
relationship. Even if receiving NO-DATA packets, the drivers transfer
packets with meaningful value in SYT field. Additionally, the order of
starting packets is always the same, independently of the source of clock.
The corresponding driver is expected as a generator of presentation
timestamp and these models can select it as a source of sampling clock.
This commit drops reusing SYT sequence from ALSA bebob driver. The driver
always transfer packets with presentation timestamp generated by ALSA
firewire stack, without re-using the sequence of value in SYT field in
incoming packets to outgoing packets.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some bebob based units tends to fail asynchronous communication when
IEEE 1394 bus is under bus-reset state. When registering sound card
instance at unit probe callback, userspace applications can be involved
to the state.
This commit postpones the registration till the bus is calm.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The 'vendor_id' argument is not used in the local function. Let's remove
it.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
DM1000/DM1100/DM1500 chipsets transfer packets with discontinue value in
'dbc' field of CIP header. For ALSA bebob driver, this makes its bus-reset
handler meaningless, because the discontinuity is detected quite earlier
than executing the handler.
This commit gives up updating streams at the bus reset handler.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The counter is incremented/decremented in critical section protected with
mutex. Therefore, no need to use atomic_t.
This commit changes the type to unsigned int.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, critical section is protected by mutex in functions of
fireworks_stream.c. Callers increments/decrements substreams counter
before calling the functions. Moving mutex to the callers code allows
to change type of the substream counter from atomic_t to unsigned int.
This commit is a preparation for obsoleting usage of atomic_t for
substream counter.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At bus-reset, DM1000/DM1100/DM1500 chipsets transfer packets with
discontinuous value in 'dbc' field of CIP header. In this case, packet
streaming layer in firewire-lib module stops streaming and set XRUN to PCM
substream.
In ALSA, PCM applications are notified the XRUN status by the return value
of ALSA PCM interface. They can recover this state by executing
snd_pcm_prepare(), then PCM drivers' prepare handler is called, and start
new PCM substream. For ALSA BeBoB driver, the handler establishes new
connections and start new AMDTP streaming.
Unfortunately, neither the PCM applications nor the driver know the reason
of XRUN. The driver gets to know the reason when update handler is called
by IEEE 1394 bus driver. As long as I tested, the order of below events are
not fixed:
* Detecting packet discontinuity in tasklet context of OHCI 1394 driver
* Calling prepare handler in process context of ALSA PCM application
* Calling update handler in kthread context of IEEE 1394 bus driver
The unpredictable order is disadvantage for the driver to be compliant to
CMP. In IEC 61883-1, new CMP establish operations should be done 1 sec
(isoc_resource_delay) after bus-reset. Within 1 sec, CMP restore
operations are allowed. For this reason, in former commit ('b6bc812327aa:
ALSA: bebob/firewire-lib: Add a quirk for discontinuity at bus reset'),
the process context is forced to wait for executing update handler. The
process context wait for bus-reset up to 1 sec. This commit solves the
issue, while causes more disadvantages. For PCM applications, calling
snd_pcm_prepare() for recovering XRUN state takes more time and the driver
got a bit complicated code, while the recovery is not always successful.
As long as I tested, DM1000/DM1100/DM1500 and BeBoB firmware can allow
drivers to establish new connections just after bus reset. Furthermore,
any FCP transactions are handled correctly. Therefore, the driver don't
need to wait for bus reset handler for starting new streaming.
This commit removes the codes to reduce maintenance cost.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The return type "unsigned int" was used by the get_formation_index function
despite of the aspect that it will eventually return a negative error code.
So, change to signed int and get index by reference in the parameters.
Done with the help of Coccinelle.
[Fix the missing braces suggested by Julia Lawall -- tiwai]
Signed-off-by: Lucas Tanure <tanure@linux.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In former commit, metering is supported for BeBoB based models
customized by M-Audio. The data in transaction is aligned to
big-endianness, while in the driver code u16 typed variable is assigned
to the data. This causes sparse warnings.
bebob_maudio.c:651:31: warning: cast to restricted __be16
bebob_maudio.c:651:31: warning: cast to restricted __be16
bebob_maudio.c:651:31: warning: cast to restricted __be16
bebob_maudio.c:651:31: warning: cast to restricted __be16
This commit fixes this bug by using __be16 variable for the data.
Fixes: 3149ac489ff8('ALSA: bebob: Add support for M-Audio special Firewire series')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When committed to upstream, these four modules had wrong entries for
Makefile. This forces them to be loadable modules even if they're set
as built-in.
This commit fixes this bug.
Fixes: b5b04336015e('ALSA: fireworks: Add skelton for Fireworks based devices')
Fixes: fd6f4b0dc167('ALSA: bebob: Add skelton for BeBoB based devices')
Fixes: 1a4e39c2e5ca('ALSA: oxfw: Move to its own directory')
Fixes: 14ff6a094815('ALSA: dice: Move file to its own directory')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The structures of type snd_bebob_clock_spec, snd_bebob_rate_spec,
snd_bebob_meter_spec, and snd_bebob_spec are never modified after they are
initialized. Make them all const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit renames some macros just related to AM824 format. In later
commit, they're moved to AM824 layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Setting the format of PCM substream to AMDTP stream structure is important
to set a handler to copy actual PCM samples between buffers. The
processing should be in data block processing layer because essentially
it has no relationship to packet streaming.
This commit renames PCM format setting function to prepare for integrating
AM824 layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, MIDI messages are transferred in MIDI conformant data
channel. Essentially, packet streaming layer is not responsible for MIDI
functionality.
This commit moves MIDI trigger helper function from the layer to AM824
layer. The rest of codes related to MIDI functionality will be moved in
later commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, several types of data are available in AM824 format. The
data is transferred in each data channel. The position of data channel in
data block differs depending on model.
Current implementation has an array to map the index of data channel in an
data block to the position of actual data channel. The implementation
allows each driver to access the mapping directly.
In later commit, the mapping is in specific structure pushed into an
opaque pointer. Helper functions are required.
This commit adds the helper functions for this purpose. In IEC 61883-6,
AM824 format supports many data types, while this specification easily
causes over-engineering. Current AM824 implementation is allowed to handle
two types of data, Multi Bit Linear Audio data (=PCM samples) and MIDI
conformant data (=MIDI messages).
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, PCM frames are transferred in Multi Bit Linear Audio data
channel. The data channel transfers 16/20/24 bit PCM samples. Thus, PCM
substream has a constrain about it.
This commit moves codes related to the constraint from packet streaming
layer to AM824 data block processing layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The value of FDF field in CIP header is protocol-dependent. Thus, it's
better to allow data block processing layer to decide the value in any
timing.
In AM824 data format, the value of FDF field in CIP header indicates
N-flag and Nominal Sampling Frequency Code (sfc). The N-flag is for
switching 'Clock-based rate control mode' and 'Command-based rate control
mode'. In our implementation, 'Clock-based rate control mode' is just
supported. Therefore, When sampling transfer frequency is decided, then
the FDF can be set.
This commit replaces 'amdtp_stream_set_parameters' with
'amdtp_am824_set_parameters' to set the FDF. This is the same timing
to decide the ration between the number of data blocks and the number of
PCM frames.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds data block processing layer for AM824 format. The new
layer initializes streaming layer with its value for fmt field.
Currently, most implementation of data block processing still remains
streaming layer. In later commits, these codes will be moved to the layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In later commit, data block processing layer will be newly added. This
layer will be named as 'amdtp-am824'.
This commit renames current amdtp file to amdtp-stream, to distinguish it
from the new layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, one data block represents one event. In ALSA, the event is
one PCM frame. Therefore, when processing one data block, current
implementation counts one PCM frame.
On the other hand, Dice platform has a quirk called as 'dual wire' at
higher sampling rate. In detail, see comment of commit 6eb6c81eee
("ALSA: dice: Split stream functionality into a file").
Currently, to handle this quirk, AMDTP stream structure has a
'double_pcm_frames' member. When this is enabled, two PCM frames are
counted. Each driver set this flag by accessing the structure member
directly.
In future commit, some members related to AM824 data block will be moved
to specific structure, to separate packet streaming layer and data block
processing layer. The access will be limited by opaque pointer.
For this reason, this commit adds an argument into
amdtp_stream_set_parameter() to set the flag.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, amdtp_stream_set_parameters() returns no error even if wrong
arguments are given. This is not good for streaming layer because drivers
can continue processing ignoring capability of streaming layer.
This commit changes this function to return error code.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In PCM core, when hw_params() in each driver returns error, the state of
PCM substream is kept as 'open'. In this case, current drivers for sound
units on IEEE 1394 bus doesn't decrement substream counter in hw_free()
correctly. This causes these drivers to keep streams even if not
required.
This commit fixes this bug. When snd_pcm_lib_alloc_vmalloc_buffer()
fails, hw_params function in each driver returns without incrementing the
counter.
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Behringer FCA610 transmits packets with periodic noisy PCM samples
when receiving no streams, and generates a bit noisy sound.
ALSA BeBoB driver is programmed to establish both in/out connections
when starting streaming, then transfers packets as userspace applications
requested. This means that there's a case that one of incoming/outgoing
streams is running, to save CPU and bandwidth usage. Although, it's natural
to start transferring packets in both direction.
This commit makes this driver to keeps duplex streams always.
Tested-by: Kim Tore Jensen <kim@incendio.no>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Behringer FCA610 and UFX1604 is confirmed to require more time till
transmitting packets after establishing connections. This seems to
be a quirk of DM1500 ASIC which ArchWave produced.
For this quirk, this commit extends the time to wait up to 2 seconds.
As a result, in worst cases, below userspace functions require 2 seconds
to return.
- snd_pcm_prepare()
- snd_pcm_hw_params()
- snd_pcm_recover()
Tested-by: Kim Tore Jensen <kim@incendio.no>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BeBoB installed devices have BeBoB register area. This area stores
basic information about its firmware. A register has its protocol
version.
This commit adds 'version' member and store the device's protocol
version to handle v3 quirks in following commits.
Tested-by: Kim Tore Jensen <kim@incendio.no>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In previous commits, this driver can detect the source of clock as mush
as possible. SYT-Match mode is also available.
This commit purge the restriction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The old string literals were completely replaced by new normalized
representation.
This commit obsoletes it.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit changes function prototype and its processing. As a result,
function caller can execute additional processing according to detected
clock source.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Previous commit adds a enumerator as a normalized representation of
clock source, while model-dependent structures still use string literals
for this purpose.
This commit is a preparation for replacement.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Previous commit allows this driver to detect several types of clock
source, while there's no normalized expression for it.
This commit adds a new enumerator for this purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With BeBoB version 3, current ALSA BeBoB driver detects the type of
current clock signal source wrongly. This is due to a lack of proper
implementation to parse the information.
This commit renews the parser. As a result, this driver detects
SYT-Match clock signal, thus it can start streams with two modes;
SYT-Match mode and the others. SYT-Match mode will be supported in future
commits.
There's a constrain about detected internal/external clock source.
When detecting external clock source, this driver allows userspace
applications to use current sampling rate only. This is due to consider
abour synchronization to external clock sources such as S/PDIF, ADAT or
word-clock.
According to several information from some devices, I guesss that the
internal clock of most devices synchronize to IEEE 1394 cycle start
packet. In this case, by a usual way, it's detect as 'Sync type
of output Music Sub-Unit' connected to 'Sync type of PCR output Unit
(oPCR)', and this driver judges it as internal clock. Therefore,
userspace applications is allowed to request arbitrary supported sampling
rates.
On the other hand, several devices based on BeBoB version 3 have
additional internal clock. In this case, by a usual way, it's detect as
'Sync/Additional type of External input Unit'. Unfortunately, there's no
way to distinguish this sync type from the other external clock sources
such as word-clock. In this case, this driver handles it as external and
userspace applications is forced to use current sampling rate.
I note that when the source of clock is detected as 'Isochronous stream
type of input PCR[0]', it's under 'SYT-Match' mode. In this mode, the
synchronization clock is generated according to SYT-series in received
packets. In this case, this driver generates the series by myself. I
experienced this mode often make the device silent suddenly during
playbacking. This means that the mode is easy to lost synchronization.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This device is based on DM1000E, and BeBoB version 1 firmware is
installed.
$ cat /proc/asound/cards
0 [Pro ]: BeBoB - Mbox 2 Pro
DIGIDESIGN Mbox 2 Pro (id:1, rev:1),
GUID 00a07e0100a90000 at fw1.0, S400
$ cat /proc/asound/Pro/firewire/firmware
Manufacturer: bridgeCo
Protocol Ver: 1
Build Ver: 0
GUID: 0x00A07E0100A90000
Model ID: 0x01
Model Rev: 1
Firmware Date: 20071031
Firmware Time: 034402
Firmware ID: 0xA9
Firmware Ver: 16777215
Base Addr: 0x20080000
Max Size: 1572864
Loader Date: 20051207
Loader Time: 205554
With this patch, ALSA BeBoB driver can start packet streaming to/from
this model, while as a default, internal multiplexer of this model is
not initialized and generates no sound even if the driver transfers
any packets with PCM samples. To hear any sounds from this model,
userspace applications should be developed to set parameters to the
internal multiplexer. You can see raw information in FFADO website:
http://subversion.ffado.org/wiki/AvcModels/DigiDesignMboxPro2
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some M-Audio devices require to receive bootup command just after
powering on, while codes in BeBoB driver doesn't work properly in
big-endian machine because the command should be aligned by
little-endian.
This commit fixes this bug. This fix should go to stable kernel.
Cc: Takayuki Shiroma <t.shiroma.oki@gmail.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A part of these drivers, especially BeBoB driver, are programmed to wait
some events. Thus the drivers should not destroy any data in .remove()
context.
This commit moves some destructors from 'struct fw_driver.remove()' to
'struct snd_card.private_free()' to shutdown safely.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently stream destructor in each driver has a problem to be called in
a context in which sound card object is released, because the destructors
call amdtp_stream_pcm_abort() and touch PCM runtime data.
The PCM runtime data is destroyed in application's context with
snd_pcm_close(), on the other hand PCM substream data is destroyed after
sound card object is released, in most case after all of ALSA character
devices are released. When PCM runtime is destroyed and PCM substream is
remained, amdtp_stream_pcm_abort() touches PCM runtime data and causes
Null-pointer-dereference.
This commit changes stream destructors and allows each driver to call
it after releasing runtime.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireworks and Dice drivers try to touch instances of FireWire unit after
sound card object is released, while references to the unit is decremented
in .remove(). When unplugging during streaming, sound card object is
released after .remove(), thus Fireworks and Dice drivers causes GPF or
Null-pointer-dereferencing to application processes because an instance of
FireWire unit was already released.
This commit adds reference-counting for FireWire unit in drivers to allow
them to touch an instance of FireWire unit after .remove(). In most case,
any operations after .remove() may be failed safely.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are several devices that expect to receive MIDI data only in the
first eight data blocks of a packet. If the driver restricts the data
rate to the allowed rate (as mandated by the specification, but not yet
implemented by this driver), this happens naturally. Therefore, there
is no reason to ever try to use more data packets with any device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_bebob_stream_check_internal_clock() may get an id from
saffirepro_both_clk_src_get (via clk_src->get()) that was uninitialized.
a) make logic in saffirepro_both_clk_src_get explicit
b) test if id used in snd_bebob_stream_check_internal_clock matches array size
[fixed missing signed prefix to *_maps[] by tiwai]
Signed-off-by: Christian Vogel <vogelchr@vogel.cx>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
