Add support to handle IGTK keys which are required for MFP to FW. Index ID
4 and 5 are used to store the IGTK key.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220524120606.9675-4-ajay.kathat@microchip.com
Enable SAE authentication for AP and STA mode. In STA mode, allow the
driver to pass the auth frames which are received from firmware to
userspace application(hostapd) so that SAE authentication is offloaded to
userspace.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220524120606.9675-3-ajay.kathat@microchip.com
Deprecated WEP security for WILC driver as well as in firmware from
15.6 FW release onwards. After WEP security removal, freeup some codespace
which helped to add new features like WPA3 etc.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220524120606.9675-2-ajay.kathat@microchip.com
For power-up sequence, WILC expects RESET set to high 5ms after making
chip_en(enable) so corrected chip power-up sequence by making RESET high.
For Power-Down sequence, the correct sequence make RESET and CHIP_EN low
without any extra delay.
Fixes: ec031ac479 ("wilc1000: Add reset/enable GPIO support to SPI driver")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220524120606.9675-1-ajay.kathat@microchip.com
'vmm_table' array contains the size of data buffer length including host
header length. In 'vmm_table' array, the Zero value means the end of
vmm_entries that needs to transfer to firmware which is calculated based on
VMM free size in firmware.
Use 'vmm_table' valid entry check before fetching the entry from TX queue to
only copy valid number of entries to avoid possible NULL pointer exception
observed sometimes during large file transfers.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220504161924.2146601-5-ajay.kathat@microchip.com
Monitor(mon.) interface is used for handling the AP mode and 'ieee80211_ptr'
reference is not getting set for it. Like earlier implementation,
use register_netdevice() instead of cfg80211_register_netdevice() which
expects valid 'ieee80211_ptr' reference to avoid the possible crash.
Fixes: 2fe8ef1062 ("cfg80211: change netdev registration/unregistration semantics")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220504161924.2146601-3-ajay.kathat@microchip.com
The function number was not correct(reset to 0) when host resumes from
suspend state. Use hardcoded value in function base information
register(FBR base address) to re-initialize correctly on host resume.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220504161924.2146601-2-ajay.kathat@microchip.com
Increase firmware version array size to hold complete version information.
The firmware commit id(Build:) information is also part of the firmware
version string.
Firmware version format:
WILC_WIFI_FW_REL_XX_XX Build: XXXXX
e.g.
WILC_WIFI_FW_REL_15_6 Build: 12804
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220504161924.2146601-1-ajay.kathat@microchip.com
This series from Uwe Kleine-König converts the spi remove function to
return void since there is nothing useful that we can do with a failure
and it as more buses are converted it'll enable further work on the
driver core.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmIdBQAACgkQJNaLcl1U
h9D1GQf/dVustBx4kCUNJt4QuMF4rozHtAzo2qK1grAnpHEqiMvVEzAuxfbTgJOx
9AUj+xEuVpPxoYUDLVJpJrxwdAl0Ue8tDRgP9Cqr/o6a3IoKrhEi+1KpSbvjcsgB
oqJEcvdjk1XAtl+QXmvyMjbMLxpz2x3Ne6dj7RL/LsfxXC0/om+NQIvJBfn78Dj2
JSNJcVtRDmdaApXfguDGA0u3COarypybYMuumIO4rRxjA5S4FXXovny4nwNXvOhS
Ki5/7GKq9rojeeIf0kD/IDdkmSS0WZp3Rc2mIrdsrXrTca+dTo3sYlcP+HMcZmtW
0+bzsht6VyApfGGZ1Ra/w3NxN6OMMg==
=TyvV
-----END PGP SIGNATURE-----
Merge tag 'spi-remove-void' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Mark Brown says:
====================
spi: Make remove() return void
This series from Uwe Kleine-König converts the spi remove function to
return void since there is nothing useful that we can do with a failure
and it as more buses are converted it'll enable further work on the
driver core.
====================
Link: https://lore.kernel.org/r/20220228173957.1262628-2-broonie@kernel.org/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
For the SDIO driver, the RESET/ENABLE pins of WILC1000 are controlled
through the SDIO power sequence driver. This commit adds analogous
support for the SPI driver. Specifically, during initialization, the
chip will be ENABLEd and taken out of RESET and during
deinitialization, the chip will be placed back into RESET and disabled
(both to reduce power consumption and to ensure the WiFi radio is
off).
Both RESET and ENABLE GPIOs are optional. However, if the ENABLE GPIO
is specified, then the RESET GPIO should normally also be specified as
otherwise there is no way to ensure proper timing of the ENABLE/RESET
sequence.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221212531.4011609-2-davidm@egauge.net
Move "chipid" variable into the per-driver structure so the code
doesn't break if more than one wilc1000 module is present.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221210538.4011227-1-davidm@egauge.net
Smatch complains that there is a double free in probe:
drivers/net/wireless/microchip/wilc1000/spi.c:186 wilc_bus_probe() error: double free of 'spi_priv'
drivers/net/wireless/microchip/wilc1000/sdio.c:163 wilc_sdio_probe() error: double free of 'sdio_priv'
The problem is that wilc_netdev_cleanup() function frees "wilc->bus_data".
That's confusing and a layering violation. Leave the frees in probe(),
delete the free in wilc_netdev_cleanup(), and add some new frees to the
remove() functions.
Fixes: dc8b338f3b ("wilc1000: use goto labels on error path")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211217150311.GC16611@kili
The wakeup and sleep commands need to be sent to the WILC chip only
when it is in power save mode (PSM, as controlled by "iw dev wlan0 set
power_save on/off"). The commands are relatively costly, so it pays
to skip them when possible.
iperf3 without this patch (no significant different with PSM on/off):
TX 0.00-120.01 sec 140 MBytes 9.82 Mbits/sec
RX 0.00-120.69 sec 283 MBytes 19.6 Mbits/sec
with this patch applied:
PSM off (TX is 46% improved, RX slightly improved; may not be significant):
TX 0.00-120.00 sec 206 MBytes 14.4 Mbits/sec
RX 0.00-120.48 sec 322 MBytes 22.4 Mbits/sec
PSM on (no significant change):
TX 0.00-120.00 sec 140 MBytes 9.78 Mbits/sec
RX 0.00-120.08 sec 257 MBytes 18.0 Mbits/sec
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211210203016.3680425-2-davidm@egauge.net
This follows normal Linux convention and is more useful since the new
name will make it apparent which network device the work-queue is for
(e.g., the name will be "wlan0-wq" for network device "wlan0").
hif_workqueue allocation has to move from
cfg80211.c:wilc_cfg80211_init() to netdev.c:wilc_netdev_ifc_init()
because the network device name is not known until after the netdev is
registered. The move also makes sense because netdev.c is already
responsible for destroying the work queue when it is no longer needed.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211209044411.3482259-5-davidm@egauge.net
This follows normal Linux conventions and is also more useful because
the netdevice name is part of the task name (e.g., "wlan0-tx" for
network device "wlan0").
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211209044411.3482259-4-davidm@egauge.net
This change follows normal Linux convention and the new name is more
useful since it'll be clear which irq handler statistics correspond to
which net device.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211209044411.3482259-3-davidm@egauge.net
The name "wilc1000_spi" follows normal Linux conventions and also is
analogous to the SDIO driver, which uses "wilc1000_sdio".
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211209044411.3482259-2-davidm@egauge.net
When deinitializing the driver, one or more "FW not responding" error
appears on the console. This appears to be due to wilc_wlan_stop()
disabling host/WILC1000 communication, but then right afterwards, it
tries to release the bus with chip-sleep enabled. The problem is
enabling the chip-sleep cannot success once host/WILC1000
communication is disabled. Fix by only releasing the bus.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211208062747.3405221-1-davidm@egauge.net
The USE_SPI_DMA macro name suggests that it could be set to 1 to
control whether or not SPI DMA should be used. However, that's not
what it does. If set to 1, it'll set the SPI messages'
"is_dma_mapped" flag to true, even though the tx/rx buffers aren't
actually DMA mapped by the driver. In other words, setting this flag
to 1 will break the driver.
Best to clean up this confusion by removing the macro altogether.
There is no need to explicitly initialize "is_dma_mapped" because the
message is cleared to zero anyhow, so "is_dma_mapped" is set to false
by default.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211207002453.3193737-1-davidm@egauge.net
The messages appears to have been copied from wilc_get_mac_address and
says "get" when it should say "set".
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211206232709.3192856-2-davidm@egauge.net
This eliminates warning message:
SPI driver WILC_SPI has no spi_device_id for microchip,wilc1000
and makes device-tree autoloading work.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211202045001.2901903-1-davidm@egauge.net
First set of patches for v5.17. The biggest change is the iwlmei
driver for Intel's AMT devices. Also now WCN6855 support in ath11k
should be usable.
Major changes:
ath10k
* fetch (pre-)calibration data via nvmem subsystem
ath11k
* enable 802.11 power save mode in station mode for qca6390 and wcn6855
* trace log support
* proper board file detection for WCN6855 based on PCI ids
* BSS color change support
rtw88
* add debugfs file to force lowest basic rate
* add quirk to disable PCI ASPM on HP 250 G7 Notebook PC
mwifiex
* add quirk to disable deep sleep with certain hardware revision in
Surface Book 2 devices
iwlwifi
* add iwlmei driver for co-operating with Intel's Active Management
Technology (AMT) devices
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmGvclcRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZtK6wgAoOoT83JKMreXlXXhVegqlJbC3HyElF5r
DJlpDDJkJUT9airol2nd0yFfP+5WFyQPrt5shsQmqz43U4jlgfFpFXZIjQufK+gn
VAGvVGfsanRXEFlsVgFZeSZvAEyEyNSggxADC03Ky0xtiCGc89r2o71jD3HA/ZzO
1X8gbKH7YLWj4G/GQkrKsvIAwzoZXT7nwQSdW73M8QVzk4OSNhLBLdiqKYq0yViM
7Ea2Vj27hiyk/RXNUZHy+bKa8vKN5sA91VHJ836aPZBQ4OLotGzF3AgHfgIhIpdr
hI4BVJbngpjQho1EkCnZZuISPes0YQWJB5hK5xpL98yuIL4wyJRfeQ==
=I8Dj
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-12-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.17
First set of patches for v5.17. The biggest change is the iwlmei
driver for Intel's AMT devices. Also now WCN6855 support in ath11k
should be usable.
Major changes:
ath10k
* fetch (pre-)calibration data via nvmem subsystem
ath11k
* enable 802.11 power save mode in station mode for qca6390 and wcn6855
* trace log support
* proper board file detection for WCN6855 based on PCI ids
* BSS color change support
rtw88
* add debugfs file to force lowest basic rate
* add quirk to disable PCI ASPM on HP 250 G7 Notebook PC
mwifiex
* add quirk to disable deep sleep with certain hardware revision in
Surface Book 2 devices
iwlwifi
* add iwlmei driver for co-operating with Intel's Active Management
Technology (AMT) devices
* tag 'wireless-drivers-next-2021-12-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (87 commits)
iwlwifi: mei: fix linking when tracing is not enabled
rtlwifi: rtl8192de: Style clean-ups
mwl8k: Use named struct for memcpy() region
intersil: Use struct_group() for memcpy() region
libertas_tf: Use struct_group() for memcpy() region
libertas: Use struct_group() for memcpy() region
wlcore: no need to initialise statics to false
rsi: Fix out-of-bounds read in rsi_read_pkt()
rsi: Fix use-after-free in rsi_rx_done_handler()
brcmfmac: Configure keep-alive packet on suspend
wilc1000: remove '-Wunused-but-set-variable' warning in chip_wakeup()
iwlwifi: mvm: read the rfkill state and feed it to iwlmei
iwlwifi: mvm: add vendor commands needed for iwlmei
iwlwifi: integrate with iwlmei
iwlwifi: mei: add debugfs hooks
iwlwifi: mei: add the driver to allow cooperation with CSME
mei: bus: add client dma interface
mwifiex: Ignore BTCOEX events from the 88W8897 firmware
mwifiex: Ensure the version string from the firmware is 0-terminated
mwifiex: Add quirk to disable deep sleep with certain hardware revision
...
====================
Link: https://lore.kernel.org/r/20211207144211.A9949C341C1@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unused variables to avoid the below warnings:
drivers/net/wireless/microchip/wilc1000/wlan.c: In function 'chip_wakeup':
>> drivers/net/wireless/microchip/wilc1000/wlan.c:620:34: warning: variable 'to_host_from_fw_bit' set but not used [-Wunused-but-set-variable]
620 | u32 to_host_from_fw_reg, to_host_from_fw_bit;
| ^~~~~~~~~~~~~~~~~~~
>> drivers/net/wireless/microchip/wilc1000/wlan.c:620:13: warning: variable 'to_host_from_fw_reg' set but not used [-Wunused-but-set-variable]
620 | u32 to_host_from_fw_reg, to_host_from_fw_bit;
| ^~~~~~~~~~~~~~~~~~~
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211115102809.1408267-1-ajay.kathat@microchip.com
wilc_set_mac_address() calls IO routines which don't guarantee
the pointer won't be written to. Make a copy.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018235021.1279697-13-kuba@kernel.org
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/0855d51423578ad019c0264dad3fe47a2e8af9c7.1633849511.git.christophe.jaillet@wanadoo.fr
Increase the WID config packet response timeout to have extra wait time for
host to receive the response message from firmware. Sometimes the WID
config response was timed out because of host interrupt latency.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-12-ajay.kathat@microchip.com
Instead of using double read for the same register, use the write register
command after the read command.
The correct sequence is to use the read value in write command instead of
reading the same register again.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-11-ajay.kathat@microchip.com
Add 'initialized' variable check before adding net/mgmt packet to TX queue
as safety check before passing the commands to the firmware.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-10-ajay.kathat@microchip.com
Add the chip reset command to initialize the WILC chip before downloading
the firmware. Also, put the chip in wake-up mode so it is ready to receive
the firmware binary from the host.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-9-ajay.kathat@microchip.com
During WILC chip wake-up sequence, the clockless status register sometimes
reports failure even when the actual status is successful. So, for the
clockless register, remove the incorrect error status reporting during the
read and write command API's.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-8-ajay.kathat@microchip.com
For SPI bus, the register read fails after read/write to the clockless
register during chip wakeup sequence. Add workaround to send CMD_RESET
command during chip wake-up sequence to overcome the issue.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-7-ajay.kathat@microchip.com
Add reset/terminate/repeat command for SPI module. In case of SPI commands
failure, the host should issue a RESET command to WILC chip to recover
from any temporary bus error.
For now, the new command support is added and later the SPI read/write
API's would be modified to make use of these commands for retry mechanism
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-6-ajay.kathat@microchip.com
Use the correct sequence to configure clockless registers for chip wake-up.
The following sequence is expected from WILC chip for wakeup:
- set wakeup bit in wakeup_reg register
- after setting the wakeup bit, read back the clock status bit for wakeup
complete.
For SDIO/SPI modules, the wakeup sequence is the same except uses different
register values so refactored the code to use common function for both
SDIO/SPI bus.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-5-ajay.kathat@microchip.com
Add new WID(WID_WOWLAN_TRIGGER) to send wake_enable information to firmware.
In 'set_wakeup' cfg80211_ops callback, the enable information was not
passed to firmware which is required to handle WOWLan trigger notification
from firmware.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-4-ajay.kathat@microchip.com
When the BSS reference holds a valid reference, it is not freed. The 'if'
condition is wrong. Instead of the 'if (bss)' check, the 'if (!bss)' check
is used.
The issue is solved by removing the unnecessary 'if' check because
cfg80211_put_bss() already performs the NULL validation.
Fixes: 6cd4fa5ab6 ("staging: wilc1000: make use of cfg80211_inform_bss_frame()")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-3-ajay.kathat@microchip.com
Move initialization & deinitialization of 'deinit_lock' mutex lock inside
wlan_init_locks() & wlan_deinit_locks() API's respectively alongside other
locks. After the movement, the client count variable(client_count) which is
used for lock init/deinit is removed.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-2-ajay.kathat@microchip.com
Move static "isinit" variable to wilc_spi structure to allow multiple
WILC1000 devices per machine.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210828151346.3012697-1-davidm@egauge.net
Use goto labels on error path for probe functions. This makes code easier
to read. With this introduce also netdev_cleanup and call it where
necessary.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210806081229.721731-2-claudiu.beznea@microchip.com
Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml
requires an "rtc" clock name.
drivers/net/wireless/microchip/wilc1000/sdio.c is using "rtc" clock name
as well. Comply with the binding in wilc1000/spi.c too.
Fixes: 854d66df74 ("staging: wilc1000: look for rtc_clk clock in spi mode")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210428025445.81953-1-tudor.ambarus@microchip.com
If the loop fails, the "while(trials--) {" loop will exit with "trials"
set to -1. The test for that expects it to end with "trials" set to 0
so the warning message will not be printed.
Fix this by changing from a post-op to a pre-op. This does mean that
we only make 99 attempts instead of 100 but that's okay.
Fixes: f135a1571a ("wilc1000: Support chip sleep over SPI")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YFS5gx/gi70zlIaO@mwanda
Linux network drivers normally disallow changing the MAC address when
the interface is up. This driver has been different in that it allows
to change the MAC address *only* when it's up. This patch brings
wilc1000 behavior more in line with other network drivers. We could
have replaced wilc_set_mac_addr() with eth_mac_addr() but that would
break existing documentation on how to change the MAC address.
Likewise, return -EADDRNOTAVAIL (not -EINVAL) when the specified MAC
address is invalid or unavailable.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210303194846.1823596-1-davidm@egauge.net
