The async version of ufshcd_hold(async == true), which is only called in
queuecommand path as for now, is expected to work in atomic context, thus
it should not sleep or schedule out. When it runs into the condition that
clocks are ON but link is still in hibern8 state, it should bail out
without flushing the clock ungate work.
Fixes: f2a785ac23 ("scsi: ufshcd: Fix race between clk scaling and ungate work")
Link: https://lore.kernel.org/r/1581392451-28743-6-git-send-email-cang@codeaurora.org
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The functionality of vendor specific ops should be handled properly in
platform specific driver, but should not count on the UFS driver.
Link: https://lore.kernel.org/r/1581392451-28743-5-git-send-email-cang@codeaurora.org
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The bus bandwidth voting is required to be done before the bus clocks are
enabled, and the unvoting is required to be done only after the bus clocks
are disabled.
Link: https://lore.kernel.org/r/1581392451-28743-4-git-send-email-cang@codeaurora.org
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This sequence change is required to avoid dips in voltage during boot-up.
Apparently, this dip is caused because in the original sequence, the
regulators are initialized in lpm mode. And then when the load is set to
high, and more current is drawn, than is allowed in lpm, the dip is seen.
Link: https://lore.kernel.org/r/1581392451-28743-3-git-send-email-cang@codeaurora.org
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Exception event can be raised by the device when system suspend is in
progress. This will result in unclocked register access in exception event
handler as clocks will be turned off during suspend. This change makes sure
to flush exception event handler work in suspend before disabling clocks to
avoid unclocked register access issue.
Link: https://lore.kernel.org/r/1581392451-28743-2-git-send-email-cang@codeaurora.org
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ADAPT is added specifically for HS Gear4 mode only. Select INITIAL ADAPT
before power mode change to G4 and select NO ADAPT before switch to non-G4
modes.
[mkp: fixed typo in header file]
Link: https://lore.kernel.org/r/1581485910-8307-3-git-send-email-cang@codeaurora.org
Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many vendors would like to disable host TX LCC during initialization
flow. Introduce a common function for all users to make drivers easier to
read and maintained. This patch does not change any functionality.
Link: https://lore.kernel.org/r/20200207070357.17169-3-stanley.chu@mediatek.com
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MediaTek UFS host requires TX LCC to be disabled on both host and device
sides. This can be done by disabling host's local TX LCC before link
startup. Correct TX LCC disabling timing in MediaTek UFS driver.
Link: https://lore.kernel.org/r/20200207070357.17169-2-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update copyrights to 2020 for files modified in the 12.6.0.4 patch set.
Link: https://lore.kernel.org/r/20200128002312.16346-13-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current code does some odd +1 over maximum xri count checks and
requires that the lun_queue_count can't be bigger than maximum xri count
divided by 8. These items are bogus.
Clean the code up to cap lun_queue_count to maximum xri count.
Link: https://lore.kernel.org/r/20200128002312.16346-10-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There was report of an odd "Fix me..." log message, which was tracked down
to the lpfc_els_rcv_rps() routine. This was in handling of a very old and
obsolete ELS - Read Port Status. The RPS ELS was defined in FC-LS-1, but
deprecated in FC-LS-2, and removed from all later FC-LS revisions. It was
replaced by the Read Diagnostic Parameters (RDP) ELS and the Link Error
Status Block descriptor.
There should be no support for the RSP ELS. Remove support from driver.
Link: https://lore.kernel.org/r/20200128002312.16346-9-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Coverity reported a memory corruption error for the fdmi attributes
routines:
CID 15768 [Memory Corruption] Out-of-bounds access on FDMI
Sloppy coding of the fmdi structures. In both the lpfc_fdmi_attr_def and
lpfc_fdmi_reg_port_list structures, a field was placed at the start of
payload that may have variable content. The field was given an arbitrary
type (uint32_t). The code then uses the field name to derive an address,
which it used in things such as memset and memcpy. The memset sizes or
memcpy lengths were larger than the arbitrary type, thus coverity reported
an error.
Fix by replacing the arbitrary fields with the real field structures
describing the payload.
Link: https://lore.kernel.org/r/20200128002312.16346-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The following error is see from the compiler:
drivers/scsi/lpfc/lpfc_init.c: In function
‘lpfc_cpuhp_get_eq’: drivers/scsi/lpfc/lpfc_init.c:12660:1:
error: the frame size of 1032 bytes is larger than 1024 bytes
[-Werror=frame-larger-than=]
The issue is due to allocating a cpumask on the stack.
Fix by converting to a dynamical allocation of the cpu mask.
Link: https://lore.kernel.org/r/20200128002312.16346-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When performing reset testing, the eq's list for related hwqs was getting
corrupted. In cases where there is not a 1:1 eq to hwq, the eq is
shared. The eq maintains a list of hwqs utilizing it in case of cpu
offlining and polling. During the reset, the hwqs are being torn down so
they can be recreated. The recreation was getting confused by seeing a
non-null eq assignment on the eq and the eq list became corrupt.
Correct by clearing the hdwq eq assignment when the hwq is cleaned up.
Link: https://lore.kernel.org/r/20200128002312.16346-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adjust FC4 Types in FDMI settings
The driver sets FDMI information registring ELS as a FC4 type. ELS is a
fc3 type and should not be registered.
Fix by removing ELS type bit when we register for FDMI Port attributes.
Link: https://lore.kernel.org/r/20200128002312.16346-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When driver is set to enable bb credit recovery, the switch displayed the
setting as inactive. If the link bounces, it switches to Active.
During link up processing, the driver currently does a MBX_READ_SPARAM
followed by a MBX_CONFIG_LINK. These mbox commands are queued to be
executed, one at a time and the completion is processed by the worker
thread. Since the MBX_READ_SPARAM is done BEFORE the MBX_CONFIG_LINK, the
BB_SC_N bit is never set the the returned values. BB Credit recovery status
only gets set after the driver requests the feature in CONFIG_LINK, which
is done after the link up. Thus the ordering of READ_SPARAM needs to follow
the CONFIG_LINK.
Fix by reordering so that READ_SPARAM is done after CONFIG_LINK. Added a
HBA_DEFER_FLOGI flag so that any FLOGI handling waits until after the
READ_SPARAM is done so that the proper BB credit value is set in the FLOGI
payload.
Fixes: 6bfb162082 ("scsi: lpfc: Fix configuration of BB credit recovery in service parameters")
Cc: <stable@vger.kernel.org> # v5.4+
Link: https://lore.kernel.org/r/20200128002312.16346-4-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a call to lpfc_get_cmd_rsp_buf_per_hdwq returns NULL (memory allocation
failure), a previously allocated lpfc_io_buf resource is leaked.
Fix by releasing the lpfc_io_buf resource in the failure path.
Fixes: d79c9e9d4b ("scsi: lpfc: Support dynamic unbounded SGL lists on G7 hardware.")
Cc: <stable@vger.kernel.org> # v5.4+
Link: https://lore.kernel.org/r/20200128002312.16346-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is occasionally seeing the following SLI Port error, requiring
reset and reinit:
Port Status Event: ... error 1=0x52004a01, error 2=0x218
The failure means an RQ timeout. That is, the adapter had received
asynchronous receive frames, ran out of buffer slots to place the frames,
and the driver did not replenish the buffer slots before a timeout
occurred. The driver should not be so slow in replenishing buffers that a
timeout can occur.
When the driver received all the frames of a sequence, it allocates an IOCB
to put the frames in. In a situation where there was no IOCB available for
the frame of a sequence, the RQ buffer corresponding to the first frame of
the sequence was not returned to the FW. Eventually, with enough traffic
encountering the situation, the timeout occurred.
Fix by releasing the buffer back to firmware whenever there is no IOCB for
the first frame.
[mkp: typo]
Link: https://lore.kernel.org/r/20200128002312.16346-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Document the locking assumptions this function relies on and also verify
these locking assumptions at runtime.
Cc: Quinn Tran <qutran@marvell.com>
Cc: Daniel Wagner <dwagner@suse.de>
Link: https://lore.kernel.org/r/20200123042345.23886-2-bvanassche@acm.org
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Not in use anymore. Remove the flag.
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Link: https://lore.kernel.org/r/20200119071432.18558-3-ming.lei@redhat.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In current UFS driver design, hba->uic_link_state will not be changed after
link enters Hibern8 state by Auto-Hibern8 mechanism. In this case,
reference clock gating will be skipped unless special handling is
implemented in vendor's callbacks.
Support reference clock gating during Auto-Hibern8 period in MediaTek
Chipsets: If link state is already in Hibern8 while Auto-Hibern8 feature is
enabled, gate reference clock in setup_clocks callback.
Link: https://lore.kernel.org/r/20200129105251.12466-5-stanley.chu@mediatek.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Auto-Hibern8 may be disabled by some vendors or sysfs in runtime even if
Auto-Hibern8 capability is supported by host. If Auto-Hibern8 capability is
supported by host but not actually enabled, Auto-Hibern8 error shall not
happen.
To fix this, provide a way to detect if Auto-Hibern8 is actually enabled
first, and bypass Auto-Hibern8 disabling case in
ufshcd_is_auto_hibern8_error().
Fixes: 8217444039 ("scsi: ufs: Add error-handling of Auto-Hibernate")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200129105251.12466-4-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If system suspend or runtime suspend mode is configured as linkoff state,
phy can be powered off and reference clock can be gated in MediaTek
Chipsets.
At the same time, remove redundant reference clock control in suspend and
resume callbacks because such control can be well-handled in setup_clocks
callback.
Link: https://lore.kernel.org/r/20200129105251.12466-3-stanley.chu@mediatek.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MediaTek Chipsets can enter proprietary UniPro low-power mode during
suspend while link is in hibern8 state. Make sure leaving low-power mode
before every link startup to prevent lockup in any possible error recovery
path.
At the same time, re-factor related funcitons to improve code readability.
Link: https://lore.kernel.org/r/20200129105251.12466-2-stanley.chu@mediatek.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are two statements that are indented one level too deeply, remove
the extraneous tabs.
[mkp: fix typo spotted by Bart]
Link: https://lore.kernel.org/r/20200126154757.42530-1-colin.king@canonical.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Connection failure processing depends on a daemon being present to (at
least) stop the connection and start recovery. This is a problem on a
multipath scenario, where if the daemon failed for whatever reason, the
SCSI path is never marked as down, multipath won't perform the failover and
IO to the device will be forever waiting for that connection to come back.
This patch performs the connection failure entirely inside the kernel.
This way, the failover can happen and pending IO can continue even if the
daemon is dead. Once the daemon comes alive again, it can execute recovery
procedures if applicable.
Cc: Mike Christie <mchristi@redhat.com>
Cc: Lee Duncan <LDuncan@suse.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20200125061925.191601-1-krisman@collabora.com
Co-developed-by: Dave Clausen <dclausen@google.com>
Co-developed-by: Nick Black <nlb@google.com>
Co-developed-by: Vaibhav Nagarnaik <vnagarnaik@google.com>
Co-developed-by: Anatol Pomazau <anatol@google.com>
Co-developed-by: Tahsin Erdogan <tahsin@google.com>
Co-developed-by: Frank Mayhar <fmayhar@google.com>
Co-developed-by: Junho Ryu <jayr@google.com>
Co-developed-by: Khazhismel Kumykov <khazhy@google.com>
Reviewed-by: Reviewed-by: Khazhismel Kumykov <khazhy@google.com>
Co-developed-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Bharath Ravi <rbharath@google.com>
Signed-off-by: Dave Clausen <dclausen@google.com>
Signed-off-by: Nick Black <nlb@google.com>
Signed-off-by: Vaibhav Nagarnaik <vnagarnaik@google.com>
Signed-off-by: Anatol Pomazau <anatol@google.com>
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Signed-off-by: Junho Ryu <jayr@google.com>
Signed-off-by: Khazhismel Kumykov <khazhy@google.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reduce code duplication by introducing the tcm_qla2xxx_{get,rel}_cmd()
functions. Introduce these functions in the tcm_qla2xxx.c source files such
that the qla_target.c source file becomes independent of the SCSI target
core header files. This patch fixes a bug, namely by ensuring that
qlt_alloc_qfull_cmd() sets cmd->se_cmd.map_tag.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Link: https://lore.kernel.org/r/20200103192719.205158-1-bvanassche@acm.org
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- fix randconfig to generate a sane .config
- rename hostprogs-y / always to hostprogs / always-y, which are
more natual syntax.
- optimize scripts/kallsyms
- fix yes2modconfig and mod2yesconfig
- make multiple directory targets ('make foo/ bar/') work
-----BEGIN PGP SIGNATURE-----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=sv4U
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- fix randconfig to generate a sane .config
- rename hostprogs-y / always to hostprogs / always-y, which are more
natual syntax.
- optimize scripts/kallsyms
- fix yes2modconfig and mod2yesconfig
- make multiple directory targets ('make foo/ bar/') work
* tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: make multiple directory targets work
kconfig: Invalidate all symbols after changing to y or m.
kallsyms: fix type of kallsyms_token_table[]
scripts/kallsyms: change table to store (strcut sym_entry *)
scripts/kallsyms: rename local variables in read_symbol()
kbuild: rename hostprogs-y/always to hostprogs/always-y
kbuild: fix the document to use extra-y for vmlinux.lds
kconfig: fix broken dependency in randconfig-generated .config
Zonefs is a very simple file system exposing each zone of a zoned block
device as a file.
Unlike a regular file system with native zoned block device support
(e.g. f2fs or the on-going btrfs effort), zonefs does not hide the
sequential write constraint of zoned block devices to the user. As a
result, zonefs is not a POSIX compliant file system. Its goal is to
simplify the implementation of zoned block devices support in
applications by replacing raw block device file accesses with a richer
file based API, avoiding relying on direct block device file ioctls
which may be more obscure to developers.
One example of this approach is the implementation of LSM
(log-structured merge) tree structures (such as used in RocksDB and
LevelDB) on zoned block devices by allowing SSTables to be stored in a
zone file similarly to a regular file system rather than as a range of
sectors of a zoned device. The introduction of the higher level
construct "one file is one zone" can help reducing the amount of changes
needed in the application while at the same time allowing the use of
zoned block devices with various programming languages other than C.
Zonefs IO management implementation uses the new iomap generic code.
Zonefs has been successfully tested using a functional test suite
(available with zonefs userland format tool on github) and a prototype
implementation of LevelDB on top of zonefs.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSRPv8tYSvhwAzJdzjdoc3SxdoYdgUCXj1y8QAKCRDdoc3SxdoY
dqozAP9J3t+Q95BgKgI5jP+XEtyYsPBTaVrvaSaViEnwtJLVoQD/ZQ1lTCZSE9OI
UkvWawkuFtLGfOxTqyA3eZrZi22Ttwk=
=YVvO
-----END PGP SIGNATURE-----
Merge tag 'zonefs-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs
Pull new zonefs file system from Damien Le Moal:
"Zonefs is a very simple file system exposing each zone of a zoned
block device as a file.
Unlike a regular file system with native zoned block device support
(e.g. f2fs or the on-going btrfs effort), zonefs does not hide the
sequential write constraint of zoned block devices to the user. As a
result, zonefs is not a POSIX compliant file system. Its goal is to
simplify the implementation of zoned block devices support in
applications by replacing raw block device file accesses with a richer
file based API, avoiding relying on direct block device file ioctls
which may be more obscure to developers.
One example of this approach is the implementation of LSM
(log-structured merge) tree structures (such as used in RocksDB and
LevelDB) on zoned block devices by allowing SSTables to be stored in a
zone file similarly to a regular file system rather than as a range of
sectors of a zoned device. The introduction of the higher level
construct "one file is one zone" can help reducing the amount of
changes needed in the application while at the same time allowing the
use of zoned block devices with various programming languages other
than C.
Zonefs IO management implementation uses the new iomap generic code.
Zonefs has been successfully tested using a functional test suite
(available with zonefs userland format tool on github) and a prototype
implementation of LevelDB on top of zonefs"
* tag 'zonefs-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
zonefs: Add documentation
fs: New zonefs file system
In order to allow the GICv4 code to link properly on 32bit ARM,
make sure we don't use 64bit divisions when it isn't strictly
necessary.
Fixes: 4e6437f12d ("irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=F1qf
-----END PGP SIGNATURE-----
Merge tag '5.6-rc-smb3-plugfest-patches' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"13 cifs/smb3 patches, most from testing at the SMB3 plugfest this week:
- Important fix for multichannel and for modefromsid mounts.
- Two reconnect fixes
- Addition of SMB3 change notify support
- Backup tools fix
- A few additional minor debug improvements (tracepoints and
additional logging found useful during testing this week)"
* tag '5.6-rc-smb3-plugfest-patches' of git://git.samba.org/sfrench/cifs-2.6:
smb3: Add defines for new information level, FileIdInformation
smb3: print warning once if posix context returned on open
smb3: add one more dynamic tracepoint missing from strict fsync path
cifs: fix mode bits from dir listing when mounted with modefromsid
cifs: fix channel signing
cifs: add SMB3 change notification support
cifs: make multichannel warning more visible
cifs: fix soft mounts hanging in the reconnect code
cifs: Add tracepoints for errors on flush or fsync
cifs: log warning message (once) if out of disk space
cifs: fail i/o on soft mounts if sessionsetup errors out
smb3: fix problem with null cifs super block with previous patch
SMB3: Backup intent flag missing from some more ops
Pull vboxfs from Al Viro:
"This is the VirtualBox guest shared folder support by Hans de Goede,
with fixups for fs_parse folded in to avoid bisection hazards from
those API changes..."
* 'work.vboxsf' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: Add VirtualBox guest shared folder (vboxsf) support
- Ensure that the PIT is set up when the local APIC is disable or
configured in legacy mode. This is caused by an ordering issue
introduced in the recent changes which skip PIT initialization when the
TSC and APIC frequencies are already known.
- Handle malformed SRAT tables during early ACPI parsing which caused an
infinite loop anda boot hang.
- Fix a long standing race in the affinity setting code which affects PCI
devices with non-maskable MSI interrupts. The problem is caused by the
non-atomic writes of the MSI address (destination APIC id) and data
(vector) fields which the device uses to construct the MSI message. The
non-atomic writes are mandated by PCI.
If both fields change and the device raises an interrupt after writing
address and before writing data, then the MSI block constructs a
inconsistent message which causes interrupts to be lost and subsequent
malfunction of the device.
The fix is to redirect the interrupt to the new vector on the current
CPU first and then switch it over to the new target CPU. This allows to
observe an eventually raised interrupt in the transitional stage (old
CPU, new vector) to be observed in the APIC IRR and retriggered on the
new target CPU and the new vector. The potential spurious interrupts
caused by this are harmless and can in the worst case expose a buggy
driver (all handlers have to be able to deal with spurious interrupts as
they can and do happen for various reasons).
- Add the missing suspend/resume mechanism for the HYPERV hypercall page
which prevents resume hibernation on HYPERV guests. This change got
lost before the merge window.
- Mask the IOAPIC before disabling the local APIC to prevent potentially
stale IOAPIC remote IRR bits which cause stale interrupt lines after
resume.
-----BEGIN PGP SIGNATURE-----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=WxKD
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for X86:
- Ensure that the PIT is set up when the local APIC is disable or
configured in legacy mode. This is caused by an ordering issue
introduced in the recent changes which skip PIT initialization when
the TSC and APIC frequencies are already known.
- Handle malformed SRAT tables during early ACPI parsing which caused
an infinite loop anda boot hang.
- Fix a long standing race in the affinity setting code which affects
PCI devices with non-maskable MSI interrupts. The problem is caused
by the non-atomic writes of the MSI address (destination APIC id)
and data (vector) fields which the device uses to construct the MSI
message. The non-atomic writes are mandated by PCI.
If both fields change and the device raises an interrupt after
writing address and before writing data, then the MSI block
constructs a inconsistent message which causes interrupts to be
lost and subsequent malfunction of the device.
The fix is to redirect the interrupt to the new vector on the
current CPU first and then switch it over to the new target CPU.
This allows to observe an eventually raised interrupt in the
transitional stage (old CPU, new vector) to be observed in the APIC
IRR and retriggered on the new target CPU and the new vector.
The potential spurious interrupts caused by this are harmless and
can in the worst case expose a buggy driver (all handlers have to
be able to deal with spurious interrupts as they can and do happen
for various reasons).
- Add the missing suspend/resume mechanism for the HYPERV hypercall
page which prevents resume hibernation on HYPERV guests. This
change got lost before the merge window.
- Mask the IOAPIC before disabling the local APIC to prevent
potentially stale IOAPIC remote IRR bits which cause stale
interrupt lines after resume"
* tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Mask IOAPIC entries when disabling the local APIC
x86/hyperv: Suspend/resume the hypercall page for hibernation
x86/apic/msi: Plug non-maskable MSI affinity race
x86/boot: Handle malformed SRAT tables during early ACPI parsing
x86/timer: Don't skip PIT setup when APIC is disabled or in legacy mode
- Make the UP version of smp_call_function_single() match SMP semantics
when called for a not available CPU. Instead of emitting a warning and
assuming that the function call target is CPU0, return a proper error
code like the SMP version does.
- Remove a superfluous check in smp_call_function_many_cond()
-----BEGIN PGP SIGNATURE-----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=XfHp
-----END PGP SIGNATURE-----
Merge tag 'smp-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull SMP fixes from Thomas Gleixner:
"Two fixes for the SMP related functionality:
- Make the UP version of smp_call_function_single() match SMP
semantics when called for a not available CPU. Instead of emitting
a warning and assuming that the function call target is CPU0,
return a proper error code like the SMP version does.
- Remove a superfluous check in smp_call_function_many_cond()"
* tag 'smp-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
smp/up: Make smp_call_function_single() match SMP semantics
smp: Remove superfluous cond_func check in smp_call_function_many_cond()
- Kernel fixes:
- Install cgroup events to the correct CPU context to prevent a
potential list double add
- Prevent am intgeer underflow in the perf mlock acounting
- Add a missing prototyp for arch_perf_update_userpage()
- Tooling:
- Add a missing unlock in the error path of maps__insert() in perf maps.
- Fix the build with the latest libbfd
- Fix the perf parser so it does not delete parse event terms, which
caused a regression for using perf with the ARM CoreSight as the sink
confuguration was missing due to the deletion.
- Fix the double free in the perf CPU map merging test case
- Add the missing ustring support for the perf probe command
-----BEGIN PGP SIGNATURE-----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=xu7D
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"A set of fixes and improvements for the perf subsystem:
Kernel fixes:
- Install cgroup events to the correct CPU context to prevent a
potential list double add
- Prevent an integer underflow in the perf mlock accounting
- Add a missing prototype for arch_perf_update_userpage()
Tooling:
- Add a missing unlock in the error path of maps__insert() in perf
maps.
- Fix the build with the latest libbfd
- Fix the perf parser so it does not delete parse event terms, which
caused a regression for using perf with the ARM CoreSight as the
sink configuration was missing due to the deletion.
- Fix the double free in the perf CPU map merging test case
- Add the missing ustring support for the perf probe command"
* tag 'perf-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf maps: Add missing unlock to maps__insert() error case
perf probe: Add ustring support for perf probe command
perf: Make perf able to build with latest libbfd
perf test: Fix test case Merge cpu map
perf parse: Copy string to perf_evsel_config_term
perf parse: Refactor 'struct perf_evsel_config_term'
kernel/events: Add a missing prototype for arch_perf_update_userpage()
perf/cgroups: Install cgroup events to correct cpuctx
perf/core: Fix mlock accounting in perf_mmap()
- Handle a subtle race between the clocksource watchdog and a concurrent
clocksource watchdog stop/start sequence correctly to prevent a timer
double add bug.
- Fix the file path for the core time namespace file.
-----BEGIN PGP SIGNATURE-----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=0zFj
-----END PGP SIGNATURE-----
Merge tag 'timers-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Two small fixes for the time(r) subsystem:
- Handle a subtle race between the clocksource watchdog and a
concurrent clocksource watchdog stop/start sequence correctly to
prevent a timer double add bug.
- Fix the file path for the core time namespace file"
* tag 'timers-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Prevent double add_timer_on() for watchdog_timer
MAINTAINERS: Correct path to time namespace source file
- Provision only ACPI enabled redistributors on GICv3
- Use the proper command colums when building the INVALL command for the
GICv3-ITS
- Ensure the allocation of the L2 vPE table for GICv4.1
- Correct the GICv4.1 VPROBASER programming so it uses the proper size
- A set of small GICv4.1 tidy up patches
- Configuration cleanup for C-SKY interrupt chip
- Clarify the function documentation for irq_set_wake() to document that
the wakeup functionality is orthogonal to the irq disable/enable
mechanism.
-----BEGIN PGP SIGNATURE-----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=a9t/
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull interrupt fixes from Thomas Gleixner:
"A set of fixes for the interrupt subsystem:
- Provision only ACPI enabled redistributors on GICv3
- Use the proper command colums when building the INVALL command for
the GICv3-ITS
- Ensure the allocation of the L2 vPE table for GICv4.1
- Correct the GICv4.1 VPROBASER programming so it uses the proper
size
- A set of small GICv4.1 tidy up patches
- Configuration cleanup for C-SKY interrupt chip
- Clarify the function documentation for irq_set_wake() to document
that the wakeup functionality is orthogonal to the irq
disable/enable mechanism"
* tag 'irq-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Rename VPENDBASER/VPROPBASER accessors
irqchip/gic-v3-its: Remove superfluous WARN_ON
irqchip/gic-v4.1: Drop 'tmp' in inherit_vpe_l1_table_from_rd()
irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level
irqchip/gic-v4.1: Set vpe_l1_base for all redistributors
irqchip/gic-v4.1: Fix programming of GICR_VPROPBASER_4_1_SIZE
genirq: Clarify that irq wake state is orthogonal to enable/disable
irqchip/gic-v3-its: Reference to its_invall_cmd descriptor when building INVALL
irqchip: Some Kconfig cleanup for C-SKY
irqchip/gic-v3: Only provision redistributors that are enabled in ACPI
recent rework of the EFI memory map parsing. On systems with invalid memmap
entries the cleanup function uses an value which cannot be relied on in
this stage. Use the actual EFI memmap entry instead.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAl5ABcYTHHRnbHhAbGlu
dXRyb25peC5kZQAKCRCmGPVMDXSYoXBWEACURHTBuiOHWFzO4tZtC8MzfVbLgNR2
aemHNslI0h/tJz+q8hEBnLnwNVS9xjwGaTl1B2Ij7Z0dJjLvcC9CrI1o7ibf0e9v
Ba4ybAs5zAUiXyLsgcckDVXbBeU9LuzeKfNe1hPPIJgFeRrftwZpLRC6GUuSXODj
cI13DF9sXxaWLZfktC5CZMcFZh5EtFYvfedAp/qMhb1ot2DdvQ9fBMexcSHKtCgT
QIZU1DTO9JtOgbyEu+PM30/ID3WYJVXHNtyLFDNgIPK80EORD2Ujlw1LmEc/BrEt
upN8sPiFMTtYDhDjgSc7tYuzF2n/on0xNM0JG8cXr2oGTb9unDxNiDK6VQ8hfDy3
8T0xK1DY6ithNSDznaLix03uNVkgh2MVCEZlb3429aM7APyn7+/O5lDo7sNVTUt5
QK/OOcf+2OvEr1VhKellze85yCIU4wOr4kiruDZXsBuu4PVyCQwnxz9JXeHb6Cg6
oWKdNT5AwdGENKmOPmjx+NBQPrWShYcYaKkA8hYMiFcewfHaL8m0FTdmcpp9XcwM
/a2nNL4STS2O1hd/60fNVAEtFVXY821OhAG6qW3mehJGJlXGijfAxCUFHGR32279
9omyu33ii/wmZ+m1rp5meAY7qHBvBWwSrRCR3UWU3h5icOaBp0zU/FQoUlhqo0pT
W9IhBcbPVy5kPA==
=AU47
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fix from Thomas Gleixner:
"A single fix for a EFI boot regression on X86 which was caused by the
recent rework of the EFI memory map parsing. On systems with invalid
memmap entries the cleanup function uses an value which cannot be
relied on in this stage. Use the actual EFI memmap entry instead"
* tag 'efi-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/x86: Fix boot regression on systems with invalid memmap entries
Five small patches, all in drivers or doc, which missed the initial
pull request. The qla2xxx and megaraid_sas are actual fixes and the
rest are spelling and doc changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXj8MoCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishUjlAQChB8+I
pBKVOfU+38vndu+YW6IRb11HhxKzY9LlHVf04wD+LxKsxuYKpZjivytfuYJGsxMD
C5EWLUxB7GYUQItEBjQ=
=7xJj
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull misc SCSI fixes from James Bottomley:
"Five small patches, all in drivers or doc, which missed the initial
pull request.
The qla2xxx and megaraid_sas are actual fixes and the rest are
spelling and doc changes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: fix spelling mistake "initilized" -> "initialized"
scsi: pm80xx: fix spelling mistake "to" -> "too"
scsi: MAINTAINERS: ufs: remove pedrom.sousa@synopsys.com
scsi: megaraid_sas: fixup MSIx interrupt setup during resume
scsi: qla2xxx: Fix unbound NVME response length
Pull networking fixes from David Miller:
1) Unbalanced locking in mwifiex_process_country_ie, from Brian Norris.
2) Fix thermal zone registration in iwlwifi, from Andrei
Otcheretianski.
3) Fix double free_irq in sgi ioc3 eth, from Thomas Bogendoerfer.
4) Use after free in mptcp, from Florian Westphal.
5) Use after free in wireguard's root_remove_peer_lists, from Eric
Dumazet.
6) Properly access packets heads in bonding alb code, from Eric
Dumazet.
7) Fix data race in skb_queue_len(), from Qian Cai.
8) Fix regression in r8169 on some chips, from Heiner Kallweit.
9) Fix XDP program ref counting in hv_netvsc, from Haiyang Zhang.
10) Certain kinds of set link netlink operations can cause a NULL deref
in the ipv6 addrconf code. Fix from Eric Dumazet.
11) Don't cancel uninitialized work queue in drop monitor, from Ido
Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
net: thunderx: use proper interface type for RGMII
mt76: mt7615: fix max_nss in mt7615_eeprom_parse_hw_cap
bpf: Improve bucket_log calculation logic
selftests/bpf: Test freeing sockmap/sockhash with a socket in it
bpf, sockhash: Synchronize_rcu before free'ing map
bpf, sockmap: Don't sleep while holding RCU lock on tear-down
bpftool: Don't crash on missing xlated program instructions
bpf, sockmap: Check update requirements after locking
drop_monitor: Do not cancel uninitialized work item
mlxsw: spectrum_dpipe: Add missing error path
mlxsw: core: Add validation of hardware device types for MGPIR register
mlxsw: spectrum_router: Clear offload indication from IPv6 nexthops on abort
selftests: mlxsw: Add test cases for local table route replacement
mlxsw: spectrum_router: Prevent incorrect replacement of local table routes
net: dsa: microchip: enable module autoprobe
ipv6/addrconf: fix potential NULL deref in inet6_set_link_af()
dpaa_eth: support all modes with rate adapting PHYs
net: stmmac: update pci platform data to use phy_interface
net: stmmac: xgmac: fix missing IFF_MULTICAST checki in dwxgmac2_set_filter
net: stmmac: fix missing IFF_MULTICAST check in dwmac4_set_filter
...
VirtualBox hosts can share folders with guests, this commit adds a
VFS driver implementing the Linux-guest side of this, allowing folders
exported by the host to be mounted under Linux.
This driver depends on the guest <-> host IPC functions exported by
the vboxguest driver.
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fix an existing bug in our user access handling, exposed by one of the bug fixes
we merged this cycle.
A fix for a boot hang on 32-bit with CONFIG_TRACE_IRQFLAGS and the recently
added CONFIG_VMAP_STACK.
Thanks to:
Christophe Leroy, Guenter Roeck.
-----BEGIN PGP SIGNATURE-----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=+Urh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix an existing bug in our user access handling, exposed by one of
the bug fixes we merged this cycle.
- A fix for a boot hang on 32-bit with CONFIG_TRACE_IRQFLAGS and the
recently added CONFIG_VMAP_STACK.
Thanks to: Christophe Leroy, Guenter Roeck.
* tag 'powerpc-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Fix CONFIG_TRACE_IRQFLAGS with CONFIG_VMAP_STACK
powerpc/futex: Fix incorrect user access blocking
This is a merge error on my part - the driver was merged into mainline
by commit c5951e7c8e ("Merge tag 'mips_5.6' of git://../mips/linux")
over a week ago, but nobody apparently noticed that it didn't actually
build due to still having a reference to the devm_ioremap_nocache()
function, removed a few days earlier through commit 6a1000bd27 ("Merge
tag 'ioremap-5.6' of git://../ioremap").
Apparently this didn't get any build testing anywhere. Not perhaps all
that surprising: it's restricted to 64-bit MIPS only, and only with the
new SGI_MFD_IOC3 support enabled.
I only noticed because the ioremap conflicts in the ARM SoC driver
update made me check there weren't any others hiding, and I found this
one.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is some material that we picked up into our tree late, or that had
more complex dependencies on more than one topic branch that makes sense
to keep separately.
- TI support for secure accelerators and hwrng on OMAP4/5
- TI camera changes for dra7 and am437x and SGX improvement due to better
reset control support on am335x, am437x and dra7
- Davinci moves to proper clocksource on DM365, and regulator/audio
improvements for DM365 and DM644x eval boards
-----BEGIN PGP SIGNATURE-----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=R7GU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC late updates from Olof Johansson:
"This is some material that we picked up into our tree late, or that
had more complex dependencies on more than one topic branch that makes
sense to keep separately.
- TI support for secure accelerators and hwrng on OMAP4/5
- TI camera changes for dra7 and am437x and SGX improvement due to
better reset control support on am335x, am437x and dra7
- Davinci moves to proper clocksource on DM365, and regulator/audio
improvements for DM365 and DM644x eval boards"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
ARM: dts: Configure interconnect target module for am437x sgx
ARM: dts: Configure sgx for dra7
ARM: dts: Configure rstctrl reset for am335x SGX
ARM: dts: dra7: Add ti-sysc node for VPE
ARM: dts: dra7: add vpe clkctrl node
ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
ARM: dts: am43xx: add support for clkout1 clock
arm: dts: dra76-evm: Add CAL and OV5640 nodes
arm: dtsi: dra76x: Add CAL dtsi node
arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
ARM: dts: DRA72: Add CAL dtsi node
ARM: dts: dra7-l4: Add ti-sysc node for CAM
ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
ARM: dts: dra7: add cam clkctrl node
ARM: OMAP2+: Drop legacy platform data for omap4 des
ARM: OMAP2+: Drop legacy platform data for omap4 sham
ARM: OMAP2+: Drop legacy platform data for omap4 aes
...
We keep this in a separate branch to avoid cross-branch conflicts, but
most of the material here is fairly boring -- some new drivers turned on
for hardware since they were merged, and some refreshed files due to
time having moved a lot of entries around.
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl4+kqgPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3l6gP/1hleyYLDm502+hzb/mFS1fUQ/JHH1/RK/J5
JhcDL2mcSLMIvLCWEl/XO0UA7wxrsVwV7mqmd2ChvHWIyXfZQG+T0gYGoXPGPxZp
BDYHJ8E+pDT3v1owouBd1qA7a+d/D3FBJKwSI53j2PIQpH9xyTlBWxosQxhPGb33
E1BV8x2W3nIU5gLHI0KnjEXgLPXngWLn43Za9wnPGkxflCYKi9SAPg4o0NBIXmJH
Fbi5QsGnhtogtQrPvOiJnYj0PgapxJPEhelZAY8wKYcjnjonELxTeAPRJ1EyBv6I
wZiR5/ySZMRQR8mvjF7EO2q1W8VmxjAYHbld0SgaZkfvy8BcgH5YkprPpvSn9Y2C
4Ivs80LBc2Qqdq8887tarDz1QYY5NJPiOFEnJtwC0FcoNmfHETxdlefwS4fiJoBe
axF6B5jDkKPiyxbVF+EbcdImGRN+WnNiKXTvJTGHXBuOZMMGNXqJPpD0Nxix7wQB
oxkkbg1NGpGIgIT6q1RyHPpddkqSPKOI8gDRTMhQhL5FcYs69xBoWQ12rFuFyMHO
gJeWCTRuLs4VVhpEhmQ8UwxSVkQz6XApvTbok3h822nHE1L8RgFuuLgCNmZQQP3C
89vOYtceEeGVSO2imkvA0pHM9Xv+/J1KviphCgzjmBi68dtBpFw8sVIus13tLUzC
WDcR9GwC
=8F5r
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC defconfig updates from Olof Johansson:
"We keep this in a separate branch to avoid cross-branch conflicts, but
most of the material here is fairly boring -- some new drivers turned
on for hardware since they were merged, and some refreshed files due
to time having moved a lot of entries around"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
ARM: configs: at91: enable MMC_SDHCI_OF_AT91 and MICROCHIP_PIT64B
arm64: defconfig: Enable Broadcom's GENET Ethernet controller
ARM: multi_v7_defconfig: Enable devfreq thermal integration
ARM: exynos_defconfig: Enable devfreq thermal integration
ARM: multi_v7_defconfig: Enable NFS v4.1 and v4.2
ARM: exynos_defconfig: Enable NFS v4.1 and v4.2
arm64: defconfig: Enable Actions Semi specific drivers
arm64: defconfig: Enable Broadcom's STB PCIe controller
arm64: defconfig: Enable CONFIG_CLK_IMX8MP by default
ARM: configs: at91: enable config flags for sam9x60 SoC
ARM: configs: at91: use savedefconfig
arm64: defconfig: Enable tegra XUDC support
ARM: defconfig: gemini: Update defconfig
arm64: defconfig: enable CONFIG_ARM_QCOM_CPUFREQ_NVMEM
arm64: defconfig: enable CONFIG_QCOM_CPR
arm64: defconfig: Enable HFPLL
arm64: defconfig: Enable CRYPTO_DEV_FSL_CAAM
ARM: imx_v6_v7_defconfig: Select the TFP410 driver
ARM: imx_v6_v7_defconfig: Enable NFS_V4_1 and NFS_V4_2 support
arm64: defconfig: Enable ATH10K_SNOC
...
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----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=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
Most of these are smaller fixes that have accrued, and some continued
cleanup of OMAP platforms towards shared frameworks.
One new SoC from Atmel/Microchip: sam9x60.
-----BEGIN PGP SIGNATURE-----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=fIjZ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"Most of these are smaller fixes that have accrued, and some continued
cleanup of OMAP platforms towards shared frameworks.
One new SoC from Atmel/Microchip: sam9x60"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (35 commits)
ARM: OMAP2+: Fix undefined reference to omap_secure_init
ARM: s3c64xx: Drop unneeded select of TIMER_OF
ARM: exynos: Drop unneeded select of MIGHT_HAVE_CACHE_L2X0
ARM: s3c24xx: Switch to atomic pwm API in rx1950
ARM: OMAP2+: sleep43xx: Call secure suspend/resume handlers
ARM: OMAP2+: Use ARM SMC Calling Convention when OP-TEE is available
ARM: OMAP2+: Introduce check for OP-TEE in omap_secure_init()
ARM: OMAP2+: Add omap_secure_init callback hook for secure initialization
ARM: at91: Documentation: add sam9x60 product and datasheet
ARM: at91: pm: use of_device_id array to find the proper shdwc node
ARM: at91: pm: use SAM9X60 PMC's compatible
ARM: imx: only select ARM_ERRATA_814220 for ARMv7-A
ARM: zynq: use physical cpuid in zynq_slcr_cpu_stop/start
ARM: tegra: Use clk_m CPU on Tegra124 LP1 resume
ARM: tegra: Modify reshift divider during LP1
ARM: tegra: Enable PLLP bypass during Tegra124 LP1
ARM: samsung: Rename Samsung and Exynos to lowercase
ARM: exynos: Correct the help text for platform Kconfig option
ARM: bcm: Select ARM_AMBA for ARCH_BRCMSTB
ARM: brcmstb: Add debug UART entry for 7216
...
