Occasionally, on playback stream ringbuffer wraparound, the EMU20K1
hardware will momentarily return 0 instead of the proper current(loop)
address. This patch handles that case, fixing the problem of playback
position corruption and subsequent loss of buffered sound data, that
occurs with some common buffering layout patterns(e.g. multiple
simultaneous output streams with differently-sized or
non-power-of-2-sized buffers).
An alternate means of fixing the problem would be to read the ca
register continuously, until two sequential reads return the same
value; however, that would be a more invasive change, has performance
implications, and isn't necessary unless there are also issues with the
value not being updated atomically in regards to individual bits or
something similar(which I have not encountered through light testing).
I have no EMU20K2 hardware to confirm if the issue is present there,
but even if it's not, this change shouldn't break anything that's not
already broken.
Signed-off-by: Sarah Bessmer <aotos@fastmail.fm>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initialize err before returning on failure, as done elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Straightforward conversion to the new pm_ops from the legacy
suspend/resume ops.
Since we change vx222, vx_core and vxpocket have to be converted,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initialise model-specific DAC and ADC parts.
Add controls for output and mic source selection.
Rename some mixer controls according to ControlNames.txt.
Remove Playback switches for Line-in and IEC958-in - these
were controlling the input mute/unmute which affected
capture too. Use the capture switches to control the
input mute/unmute instead - it's less confusing.
Initialise the WM8775 to invert the left-right clock
to swap the left and right channels of the mic and aux
input.
Signed-off-by: Harry Butterworth <heb1001@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
After hours of debugging, I finally found the reason why some source
and runtime combination does not work. The PTP (page table pages)
address must be aligned. I am not sure how much, but alignment to
PAGE_SIZE is sufficient. Also, use ALSA's page allocation routines
to ensure proper virtual -> physical address translation.
Cc: <stable@kernel.org>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The variables are unsigned so the test `>= 0' is always true,
the `< 0' test always fails. In these cases the other part of
the test catches wrapped values.
In dac_audio_write() there does not occur a test for wrapped
values, but the test appears redundant.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On Soundblaster X-FI Titenium with emu20k2 the SIDE and SURROUND mute
functions are swapped.
It was checked with 'speaker-test -c 8 -s 3' and (un)mute surround or
'speaker-test -c 8 -s 7' and (un)mute side. The volume seems not
to be affected and works as expected.
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the suspend/resume support to ctxfi driver.
The team tested on the following seems ok:
AMD Athlon 64 3500+ / ASUS A8N-E / 512MB DDR ATI / Radeon X1300
20k1 & 20k2 cards
Signed-off-by: Wai Yew CHAY <wychay@ctl.creative.com>
Singed-off-by: Ryan RICHARDS <ryan_richards@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow unknown PCI SSIDs for emu20k1 and emu20k2 as "unknown" model.
Also, add a black-list check in case any device has to be listed
as "unsupported". It has a negative value in the pci quirk entry.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The spinlock in atc can cause a sleep in lock:
Kernel failure message 1:
BUG: sleeping function called from invalid context at mm/slub.c:1599
in_atomic(): 0, irqs_disabled(): 1, pid: 2537, name: gstreamer-prope
Pid: 2537, comm: gstreamer-prope Tainted: P
2.6.29.4-167.fc11.x86_64 #1
Call Trace:
[<ffffffff8103ff0f>] __might_sleep+0x10b/0x110
[<ffffffff810cd734>] __kmalloc+0x73/0x130
[<ffffffffa0b4b142>] ? daio_rsc_init+0xaa/0x125 [snd_ctxfi]
[<ffffffffa0b4b212>] dao_rsc_init+0x55/0x1c0 [snd_ctxfi]
[<ffffffffa0b4b3d2>] dao_rsc_reinit+0x55/0x5d [snd_ctxfi]
[<ffffffff813abd6c>] ? _spin_lock_irqsave+0x32/0x3b
[<ffffffffa0b454fe>] atc_spdif_out_passthru+0x92/0x136 [snd_ctxfi]
...
Since the lock path is no critical path, it can be gracefully
replaced with a mutex.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the PCM resources are allocated only once and ever in prepare
callback, assuming that the PCM parameters are never changed. But it's
not true.
This patch adds the call of atc->pcm_release_resources() at hw_params
and hw_free callbacks to assure that the PCM setup is done correctly
for each h/w parameter changes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The SRC instances may not exist when PCM pointer callback is called at
the state before initialization is finished. Add the NULL check just
to be sure.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CTUAA should be checked instead of CTHENDRIX. The latter is for 20k2 chip.
Also, fixed the detection of UAA/HENDRIX models by fixing the mask bits.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clean up probe routines and model detection routines so that the driver
won't call and check the PCI subsystem id at each time.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Use static tables instead of assigining each funciton pointer
- Add __devinit* to appropriate places; pcm, mixer and timer cannot be
marked because they are kept in the function table that lives long
- Move create_alsa_devs function out of struct ct_atc to mark it
__devinit
Signed-off-by: Takashi Iwai <tiwai@suse.de>
emu20k1 has a native timer interrupt based on the audio clock, which
is more accurate than the system timer (from the synchronization POV).
This patch adds the code to handle this with multiple streams.
The system timer is still used on emu20k2, and can be used also for
emu20k1 easily by changing USE_SYSTEM_TIMER to 1 in cttimer.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The device seems supporting only U8, S16, S24_3LE, S32. Other linear
formats result in bad outputs.
Also, added the support for 32bit float format, which wasn't listed
in the original code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
PCM names for surround streams should be also fixed as well as the mixer
element names. Also, a bit clean up for PCM name setup.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The prepare callback can be called multiple times, thus it needs to
release and acquire the resource again by itself at the second or later
call.
Simply add pcm_release_resources() at the beginning of each prepare
callback in ctatc.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
