This fixes a kernel oops when unloading the driver due to usb_put_phy
being called after usb_phy_generic_unregister when the device is
detached. Calling usb_phy_generic_unregister causes x->dev->driver to
be NULL in usb_put_phy and results in a NULL pointer dereference.
Cc: stable@vger.kernel.org # v4.3+
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sunxi musb has a bug where sometimes it will generate a babble
error on device disconnect instead of a disconnect IRQ. When this
happens the musb controller switches from host mode to device mode
(it clears MUSB_DEVCTL_HM/MUSB_DEVCTL_SESSION and sets
MUSB_DEVCTL_BDEVICE) and gets stuck in this state.
The babble error is misdetected as a bus reset because MUSB_DEVCTL_HM
was cleared.
To fix this, use is_host_active() rather than (devctl & MUSB_DEVCTL_HM)
to detect babble error so that sunxi musb babble recovery can handle it
by restoring the mode. This information is provided by the driver logic
and does not rely on register contents.
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the number of channels is set to 15 but in the case of DA8xx,
the number of channels is 4.
Update the driver to configure the number of channels at runtime.
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The way to configure the DMA mode on DA8xx is different from DSPS.
Add a new function to configure DMA mode on DA8xx and use a callback
to call the right function based on the platform.
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DA8xx and DSPS platforms don't use the same address for few registers.
On Da8xx, this is causing some issues (e.g. teardown that doesn't work).
Configure the address of the register during the init and use them instead
of constants.
Cc: stable@vger.kernel.org # v4.12+
Reported-by: nsekhar@ti.com
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The musb delayed irq work was never flushed on suspend, something which
since 4.9 can lead to an external abort if the work is scheduled after
the grandparent's clock has been disabled:
PM: Suspending system (mem)
PM: suspend of devices complete after 125.224 msecs
PM: suspend devices took 0.132 seconds
PM: late suspend of devices complete after 7.423 msecs
PM: noirq suspend of devices complete after 7.083 msecs
suspend debug: Waiting for 5 second(s).
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd0262c60
...
[<c054880c>] (musb_default_readb) from [<c0547b5c>] (musb_irq_work+0x48/0x220)
[<c0547b5c>] (musb_irq_work) from [<c014f8a4>] (process_one_work+0x1f4/0x758)
[<c014f8a4>] (process_one_work) from [<c014fe5c>] (worker_thread+0x54/0x514)
[<c014fe5c>] (worker_thread) from [<c015704c>] (kthread+0x128/0x158)
[<c015704c>] (kthread) from [<c0109330>] (ret_from_fork+0x14/0x24)
Commit 2bff3916fd ("usb: musb: Fix PM for hub disconnect") started
scheduling musb_irq_work with a delay of up to a second and with
retries thereby making this easy to trigger, for example, by suspending
shortly after a disconnect.
Note that we set a flag to prevent the irq work from rescheduling itself
during suspend and instead process a disconnect immediately. This takes
care of the case where we are disconnected shortly before suspending.
However, when in host mode, a disconnect while suspended will still
go unnoticed and thus prevent the controller from runtime suspending
upon resume as the session bit is always set. This will need to be
addressed separately.
Fixes: 550a7375fe ("USB: Add MUSB and TUSB support")
Fixes: 467d5c9807 ("usb: musb: Implement session bit based runtime PM for musb-core")
Fixes: 2bff3916fd ("usb: musb: Fix PM for hub disconnect")
Cc: stable <stable@vger.kernel.org> # 4.9
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current session-bit quirk implementation does not prevent the retry
counter from underflowing, something which could break runtime PM and
keep the device active for a very long time (about 2^32 seconds) after a
disconnect.
This notably breaks the B-device timeout case, but could potentially
cause problems also when the controller is operating as an A-device.
Fixes: 2bff3916fd ("usb: musb: Fix PM for hub disconnect")
Cc: stable <stable@vger.kernel.org> # 4.9
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Elatec TWN3 has the union descriptor on data interface. This results in
failure to bind the device to the driver with the following log:
usb 1-1.2: new full speed USB device using streamplug-ehci and address 4
usb 1-1.2: New USB device found, idVendor=09d8, idProduct=0320
usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.2: Product: RFID Device (COM)
usb 1-1.2: Manufacturer: OEM
cdc_acm 1-1.2:1.0: Zero length descriptor references
cdc_acm: probe of 1-1.2:1.0 failed with error -22
Adding the NO_UNION_NORMAL quirk for the device fixes the issue.
`lsusb -v` of the device:
Bus 001 Device 003: ID 09d8:0320
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 32
idVendor 0x09d8
idProduct 0x0320
bcdDevice 3.00
iManufacturer 1 OEM
iProduct 2 RFID Device (COM)
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 67
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 250mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 2
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 0
CDC Header:
bcdCDC 1.10
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
CDC ACM:
bmCapabilities 0x06
sends break
line coding and serial state
CDC Union:
bMasterInterface 0
bSlaveInterface 1
Device Status: 0x0000
(Bus Powered)
Signed-off-by: Maksim Salau <msalau@iotecha.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Taking the uurb->buffer_length userspace passes in as a maximum for the
actual urbs transfer_buffer_length causes 2 serious issues:
1) It breaks isochronous support for all userspace apps using libusb,
as existing libusb versions pass in 0 for uurb->buffer_length,
relying on the kernel using the lenghts of the usbdevfs_iso_packet_desc
descriptors passed in added together as buffer length.
This for example causes redirection of USB audio and Webcam's into
virtual machines using qemu-kvm to no longer work. This is a userspace
ABI break and as such must be reverted.
Note that the original commit does not protect other users / the
kernels memory, it only stops the userspace process making the call
from shooting itself in the foot.
2) It may cause the kernel to program host controllers to DMA over random
memory. Just as the devio code used to only look at the iso_packet_desc
lenghts, the host drivers do the same, relying on the submitter of the
urbs to make sure the entire buffer is large enough and not checking
transfer_buffer_length.
But the "USB: devio: Don't corrupt user memory" commit now takes the
userspace provided uurb->buffer_length for the buffer-size while copying
over the user-provided iso_packet_desc lengths 1:1, allowing the user
to specify a small buffer size while programming the host controller to
dma a lot more data.
(Atleast the ohci, uhci, xhci and fhci drivers do not check
transfer_buffer_length for isoc transfers.)
This reverts commit fa1ed74eb1 ("USB: devio: Don't corrupt user memory")
fixing both these issues.
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
*) Handle error return values in rockchip-typec and tegra-xusb
*) Fix MUX error check and ioremap_resource error check in mvebu-cp110-comphy
*) Fix NULL pointer dereference error in phy-mtk-tphy
*) Make sure pipe selector is not set to incompatible value
*) Fix flaky aux channel communication with rockchip-typec PHY
*) Fix DP monitors detection issue in rockchip-typec PHY
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yoPS
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.14-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: for 4.14 -rc
*) Handle error return values in rockchip-typec and tegra-xusb
*) Fix MUX error check and ioremap_resource error check in mvebu-cp110-comphy
*) Fix NULL pointer dereference error in phy-mtk-tphy
*) Make sure pipe selector is not set to incompatible value
*) Fix flaky aux channel communication with rockchip-typec PHY
*) Fix DP monitors detection issue in rockchip-typec PHY
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
xhci_stop_device() calls xhci_queue_stop_endpoint() multiple times
without checking the return value. xhci_queue_stop_endpoint() can
return error if the HC is already halted or unable to queue commands.
This can cause a deadlock condition as xhci_stop_device() would
end up waiting indefinitely for a completion for the command that
didn't get queued. Fix this by checking the return value and bailing
out of xhci_stop_device() in case of error. This patch happens to fix
potential memory leaks of the allocated command structures as well.
Fixes: c311e391a7 ("xhci: rework command timeout and cancellation,")
Cc: <stable@vger.kernel.org>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a URB is cancled, xhci driver turns the untransferred trbs
into no-ops. If an endpoint stalls on a no-op trb that belongs
to the cancelled URB, the event handler won't reset the endpoint.
Hence, it will stay halted.
Link: http://marc.info/?l=linux-usb&m=149582598330127&w=2
Cc: <stable@vger.kernel.org>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KASAN reported use-after-free bug when xhci host controller died:
[ 176.952537] BUG: KASAN: use-after-free in xhci_handle_command_timeout+0x68/0x224
[ 176.960846] Write of size 4 at addr ffffffc0cbb01608 by task kworker/3:3/1680
...
[ 177.180644] Freed by task 0:
[ 177.183882] kasan_slab_free+0x90/0x15c
[ 177.188194] kfree+0x114/0x28c
[ 177.191630] xhci_cleanup_command_queue+0xc8/0xf8
[ 177.196916] xhci_hc_died+0x84/0x358
Problem here is that when the cmd_timer fired, it would try to access
current_cmd while the command queue is already freed by xhci_hc_died().
Cleanup current_cmd in xhci_cleanup_command_queue() to avoid that.
Fixes: d9f11ba9f1 ("xhci: Rework how we handle unresponsive or hoptlug removed hosts")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many USB 3.1 capable hosts never updated the Serial Bus Release Number
(SBRN) register to USB 3.1 from USB 3.0
xhci driver identified USB 3.1 capable hosts based on this SBRN register,
which according to specs "contains the release of the Universal Serial
Bus Specification with which this Universal Serial Bus Host Controller
module is compliant." but still in october 2017 gives USB 3.0 as
the only possible option.
Make an additional check for USB 3.1 support and enable it if the xHCI
supported protocol capablity lists USB 3.1 capable ports.
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mount i_version flag is not enabled in the new sb_flags. This patch
adds the missing SB_I_VERSION flag.
Fixes: e462ec5 "VFS: Differentiate mount flags (MS_*) from internal
superblock flags"
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
by cleanning up drvdata at unbind.
- Fix potential NULL pointer dereference issue in suspend/resume
by setting drm_dev after checking if drm_dev is null or not.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=POct
-----END PGP SIGNATURE-----
Merge tag 'exynos-drm-fixes-for-v4.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
- Fix potential use-after-free issue in suspend/resume
by cleanning up drvdata at unbind.
- Fix potential NULL pointer dereference issue in suspend/resume
by setting drm_dev after checking if drm_dev is null or not.
* tag 'exynos-drm-fixes-for-v4.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: Clear drvdata after component unbind
drm/exynos: Fix potential NULL pointer dereference in suspend/resume paths
HDMI Mode selection on CNL is on CFGCR0 for that PLL, not
on in a global CTRL1 as it was on SKL.
The original patch addressed this difference, but leaving behind
this single entry here. So we were checking the wrong bits during
the PLL initialization and consequently avoiding the CFGCR1 setup
during HDMI initialization. Luckly when only HDMI was in use BIOS
had already setup this for us. But the dual display with hot plug
were messed up.
Fixes: a927c927de ("drm/i915/cnl: Initialize PLLs")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Kahola, Mika <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171003220859.21352-3-rodrigo.vivi@intel.com
(cherry picked from commit 614ee07acf)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
On PLL Enable sequence we need to "Configure DPCLKA_CFGCR0 to turn on
the clock for the DDI and map the DPLL to the DDI"
So we first do the map and then we unset DDI_CLK_OFF to turn the clock
on. We do this in 2 separated steps.
However, on this second step where we should only unset the off bit we are
also unmapping the ddi from the pll. So we end up using the pll 0
for almost everything. Consequently breaking cases with more than one
display.
Fixes: 555e38d273 ("drm/i915/cnl: DDI - PLL mapping")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Kahola, Mika <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171003220859.21352-2-rodrigo.vivi@intel.com
(cherry picked from commit 87145d95c3)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The compiler warns:
drivers/gpu/drm/i915/intel_ddi.c:118:35: warning: ‘bdw_ddi_translations_fdi’ defined but not used
Lo and behold, if we look at intel_ddi_get_buf_trans_fdi(), it uses
hsw_ddi_translations_fdi[] for both Haswell and *Broadwell*
Fixes: 7d1c42e679 ("drm/i915: Refactor code to select the DDI buf translation table")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.12+
Link: https://patchwork.freedesktop.org/patch/msgid/20171013154735.27163-1-chris@chris-wilson.co.uk
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit 1210d38890)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In the full-ppgtt world, we can fill the GGTT full of context objects.
These context objects are currently implicitly tracked by the requests
that pin them i.e. they are only unpinned when the request is completed
and retired, but we do not have the link from the vma to the request
(anymore). In order to unpin those contexts, we have to issue another
request and wait upon the switch to the kernel context.
The bug during eviction was that we assumed that a full GGTT meant we
would have requests on the GGTT timeline, and so we missed situations
where those requests where merely in flight (and when even they have not
yet been submitted to hw yet). The fix employed here is to change the
already-is-idle test to no look at the execution timeline, but count the
outstanding requests and then check that we have switched to the kernel
context. Erring on the side of overkill here just means that we stall a
little longer than may be strictly required, but we only expect to hit
this path in extreme corner cases where returning an erroneous error is
worse than the delay.
v2: Logical inversion when swapping over branches.
Fixes: 80b204bce8 ("drm/i915: Enable multiple timelines")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171012125726.14736-1-chris@chris-wilson.co.uk
(cherry picked from commit 55b4f1ce2f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
-----BEGIN PGP SIGNATURE-----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=Iwyf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-10-16' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just a single fix, for a WoWLAN-related part of CVE-2017-13080.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing dev tx_queue_len via netlink or net-sysfs,
a NETDEV_CHANGE_TX_QUEUE_LEN event notification will be
called.
But dev_ioctl missed this event notification, which could
cause no userspace notification would be sent.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7091d8c '(net/sched: cls_flower: Add offload support using egress
Hardware device') made sure (when fl_hw_replace_filter is called) to put
the egress_dev mark on persisent structure instance. Hence, following calls
into the HW driver for stats and deletion will note it and act accordingly.
With commit de4784ca03 this property is lost and hence when called,
the HW driver failes to operate (stats, delete) on the offloaded flow.
Fix it by setting the egress_dev flag whenever the ingress device is
different from the hw device since this is exactly the condition under
which we're calling into the HW driver through the egress port net-device.
Fixes: de4784ca03 ('net: sched: get rid of struct tc_to_netdev')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roi Dayan <roid@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
register_netdevice() could fail early when we have an invalid
dev name, in which case ->ndo_uninit() is not called. For tun
device, this is a problem because a timer etc. are already
initialized and it expects ->ndo_uninit() to clean them up.
We could move these initializations into a ->ndo_init() so
that register_netdevice() knows better, however this is still
complicated due to the logic in tun_detach().
Therefore, I choose to just call dev_get_valid_name() before
register_netdevice(), which is quicker and much easier to audit.
And for this specific case, it is already enough.
Fixes: 96442e4242 ("tuntap: choose the txq based on rxq")
Reported-by: Dmitry Alexeev <avekceeb@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC791 specifies the minimum MTU to be 68, while xen-net{front|back}
drivers use a minimum value of 0.
When set MTU to 0~67 with xen_net{front|back} driver, the network
will become unreachable immediately, the guest can no longer be pinged.
xen_net{front|back} should not allow the user to set this value which causes
network problems.
Reported-by: Chen Shi <cheshi@redhat.com>
Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
IFLA_IFALIAS is defined as NLA_STRING. It means that the minimal length of
the attribute is 1 ("\0"). However, to remove an alias, the attribute
length must be 0 (see dev_set_alias()).
Let's define the type to NLA_BINARY to allow 0-length string, so that the
alias can be removed.
Example:
$ ip l s dummy0 alias foo
$ ip l l dev dummy0
5: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether ae:20:30:4f:a7:f3 brd ff:ff:ff:ff:ff:ff
alias foo
Before the patch:
$ ip l s dummy0 alias ""
RTNETLINK answers: Numerical result out of range
After the patch:
$ ip l s dummy0 alias ""
$ ip l l dev dummy0
5: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether ae:20:30:4f:a7:f3 brd ff:ff:ff:ff:ff:ff
CC: Oliver Hartkopp <oliver@hartkopp.net>
CC: Stephen Hemminger <stephen@networkplumber.org>
Fixes: 96ca4a2cc1 ("net: remove ifalias on empty given alias")
Reported-by: Julien FLoret <julien.floret@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long says:
====================
rtnetlink: a bunch of fixes for userspace notifications in changing dev properties
Whenever any property of a link, address, route, etc. changes by whatever way,
kernel should notify the programs that listen for such events in userspace.
The patchet "rtnetlink: Cleanup user notifications for netdev events" tried to
fix a redundant notifications issue, but it also introduced a side effect.
After that, user notifications could only be sent when changing dev properties
via netlink api. As it removed some events process in rtnetlink_event where
the notifications was sent to users.
It resulted in no notification generated when dev properties are changed via
other ways, like ioctl, sysfs, etc. It may cause some user programs doesn't
work as expected because of the missing notifications.
This patchset will fix it by bringing some of these netdev events back and
also fix the old redundant notifications issue with a proper way.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
NETDEV_CHANGE_TX_QUEUE_LEN event process in rtnetlink_event would
send a notification for userspace and tx_queue_len's setting in
do_setlink would trigger NETDEV_CHANGE_TX_QUEUE_LEN.
So it shouldn't set DO_SETLINK_NOTIFY status for this change to
send a notification any more.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check 'status & DO_SETLINK_NOTIFY' in do_setlink doesn't really
work after status & DO_SETLINK_MODIFIED, as:
DO_SETLINK_MODIFIED 0x1
DO_SETLINK_NOTIFY 0x3
Considering that notifications are suppposed to be sent only when
status have the flag DO_SETLINK_NOTIFY, the right check would be:
(status & DO_SETLINK_NOTIFY) == DO_SETLINK_NOTIFY
This would avoid lots of duplicated notifications when setting some
properties of a link.
Fixes: ba9989069f ("rtnl/do_setlink(): notify when a netdev is modified")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
libteam needs this event notification in userspace when dev's master
dev has been changed. After this, the redundant notifications issue
would be fixed in the later patch 'rtnetlink: check DO_SETLINK_NOTIFY
correctly in do_setlink'.
Fixes: b6b36eb23a ("rtnetlink: Do not generate notifications for NETDEV_CHANGEUPPER event")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As I said in patch 'rtnetlink: bring NETDEV_CHANGEMTU event process back
in rtnetlink_event', removing NETDEV_POST_TYPE_CHANGE event was not the
right fix for the redundant notifications issue.
So bring this event process back to rtnetlink_event and the old redundant
notifications issue would be fixed in the later patch 'rtnetlink: check
DO_SETLINK_NOTIFY correctly in do_setlink'.
Fixes: aef091ae58 ("rtnetlink: Do not generate notifications for POST_TYPE_CHANGE event")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same fix for changing mtu in the patch 'rtnetlink: bring
NETDEV_CHANGEMTU event process back in rtnetlink_event' is
needed for changing tx_queue_len.
Note that the redundant notifications issue for tx_queue_len
will be fixed in the later patch 'rtnetlink: do not send
notification for tx_queue_len in do_setlink'.
Fixes: 27b3b551d8 ("rtnetlink: Do not generate notifications for NETDEV_CHANGE_TX_QUEUE_LEN event")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 085e1a65f0 ("rtnetlink: Do not generate notifications for MTU
events") tried to fix the redundant notifications issue when ip link
set mtu by removing NETDEV_CHANGEMTU event process in rtnetlink_event.
But it also resulted in no notification generated when dev's mtu is
changed via other methods, like:
'ifconfig eth1 mtu 1400' or 'echo 1400 > /sys/class/net/eth1/mtu'
It would cause users not to be notified by this change.
This patch is to fix it by bringing NETDEV_CHANGEMTU event back into
rtnetlink_event, and the redundant notifications issue will be fixed
in the later patch 'rtnetlink: check DO_SETLINK_NOTIFY correctly in
do_setlink'.
Fixes: 085e1a65f0 ("rtnetlink: Do not generate notifications for MTU events")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last cleanup introduced two harmless warnings:
fs/xfs/xfs_fsmap.c:480:1: warning: '__xfs_getfsmap_rtdev' defined but not used
fs/xfs/xfs_fsmap.c:372:1: warning: 'xfs_getfsmap_rtdev_rtbitmap_helper' defined but not used
This moves those two functions as well.
Fixes: bb9c2e5433 ("xfs: move more RT specific code under CONFIG_XFS_RT")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The writeback rework in commit fbcc025613 ("xfs: Introduce
writeback context for writepages") introduced a subtle change in
behavior with regard to the block mapping used across the
->writepages() sequence. The previous xfs_cluster_write() code would
only flush pages up to EOF at the time of the writepage, thus
ensuring that any pages due to file-extending writes would be
handled on a separate cycle and with a new, updated block mapping.
The updated code establishes a block mapping in xfs_writepage_map()
that could extend beyond EOF if the file has post-eof preallocation.
Because we now use the generic writeback infrastructure and pass the
cached mapping to each writepage call, there is no implicit EOF
limit in place. If eofblocks trimming occurs during ->writepages(),
any post-eof portion of the cached mapping becomes invalid. The
eofblocks code has no means to serialize against writeback because
there are no pages associated with post-eof blocks. Therefore if an
eofblocks trim occurs and is followed by a file-extending buffered
write, not only has the mapping become invalid, but we could end up
writing a page to disk based on the invalid mapping.
Consider the following sequence of events:
- A buffered write creates a delalloc extent and post-eof
speculative preallocation.
- Writeback starts and on the first writepage cycle, the delalloc
extent is converted to real blocks (including the post-eof blocks)
and the mapping is cached.
- The file is closed and xfs_release() trims post-eof blocks. The
cached writeback mapping is now invalid.
- Another buffered write appends the file with a delalloc extent.
- The concurrent writeback cycle picks up the just written page
because the writeback range end is LLONG_MAX. xfs_writepage_map()
attributes it to the (now invalid) cached mapping and writes the
data to an incorrect location on disk (and where the file offset is
still backed by a delalloc extent).
This problem is reproduced by xfstests test generic/464, which
triggers racing writes, appends, open/closes and writeback requests.
To address this problem, trim the mapping used during writeback to
within EOF when the mapping is validated. This ensures the mapping
is revalidated for any pages encountered beyond EOF as of the time
the current mapping was cached or last validated.
Reported-by: Eryu Guan <eguan@redhat.com>
Diagnosed-by: Eryu Guan <eguan@redhat.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Commit 332391a993 ("fs: Fix page cache inconsistency when mixing
buffered and AIO DIO") moved page cache invalidation from
iomap_dio_rw() to iomap_dio_complete() for iomap based direct write
path, but before the dio->end_io() call, and it re-introdued the bug
fixed by commit c771c14baa ("iomap: invalidate page caches should
be after iomap_dio_complete() in direct write").
I found this because fstests generic/418 started failing on XFS with
v4.14-rc3 kernel, which is the regression test for this specific
bug.
So similarly, fix it by moving dio->end_io() (which does the
unwritten extent conversion) before page cache invalidation, to make
sure next buffer read reads the final real allocations not unwritten
extents. I also add some comments about why should end_io() go first
in case we get it wrong again in the future.
Note that, there's no such problem in the non-iomap based direct
write path, because we didn't remove the page cache invalidation
after the ->direct_IO() in generic_file_direct_write() call, but I
decided to fix dio_complete() too so we don't leave a landmine
there, also be consistent with iomap_dio_complete().
Fixes: 332391a993 ("fs: Fix page cache inconsistency when mixing buffered and AIO DIO")
Signed-off-by: Eryu Guan <eguan@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Lukas Czerner <lczerner@redhat.com>
Recently we've had warnings arise from the vm handing us pages
without bufferheads attached to them. This should not ever occur
in XFS, but we don't defend against it properly if it does. The only
place where we remove bufferheads from a page is in
xfs_vm_releasepage(), but we can't tell the difference here between
"page is dirty so don't release" and "page is dirty but is being
invalidated so release it".
In some places that are invalidating pages ask for pages to be
released and follow up afterward calling ->releasepage by checking
whether the page was dirty and then aborting the invalidation. This
is a possible vector for releasing buffers from a page but then
leaving it in the mapping, so we really do need to avoid dirty pages
in xfs_vm_releasepage().
To differentiate between invalidated pages and normal pages, we need
to clear the page dirty flag when invalidating the pages. This can
be done through xfs_vm_invalidatepage(), and will result
xfs_vm_releasepage() seeing the page as clean which matches the
bufferhead state on the page after calling block_invalidatepage().
Hence we can re-add the page dirty check in xfs_vm_releasepage to
catch the case where we might be releasing a page that is actually
dirty and so should not have the bufferheads on it removed. This
will remove one possible vector of "dirty page with no bufferheads"
and so help narrow down the search for the root cause of that
problem.
Signed-Off-By: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Moving the early IDT setup out of assembly code breaks the boot on first
generation 486 systems.
The reason is that the call of idt_setup_early_handler, which sets up the
early handlers was added after the call to cr4_init_shadow().
cr4_init_shadow() tries to read CR4 which is not available on those
systems. The accessor function uses a extable fixup to handle the resulting
fault. As the IDT is not set up yet, the cr4 read exception causes an
instantaneous reboot for obvious reasons.
Call idt_setup_early_handler() before cr4_init_shadow() so IDT is set up
before the first exception hits.
Fixes: 87e81786b1 ("x86/idt: Move early IDT setup out of 32-bit asm")
Reported-and-tested-by: Matthew Whitehead <whiteheadm@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1710161210290.1973@nanos
We have implemented delayed ring mmio switch mechanism to reduce
unnecessary mmio switch. While the vGPU is being destroyed or
detached from VM, we need to force the ring switch to host context.
The later deadline is missed. Then it got a chance that word load
from VM2 might execute under the ring context of VM1 which was
attached to a same vGPU instance. Finally, the GPU is hang.
This patch guarantee the two deadline are performed.
v2: Remove unused variable 'scheduler'
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Jiri and Namhyung have long contributed a lot of code and time reviewing
patches to tools/, so lets make that reflected in the MAINTAINERS file
to encourage patch submitters to add them to the CC list, speeding up
the process of tools/perf/ patch processing.
Acked-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-onicopw68bg6kn56lnybfpns@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add native DSD support quirk for Pro-Ject Pre Box S2 Digital USB id
2772:0230.
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a key is reinstalled we can reset the replay counters
etc. which can lead to nonce reuse and/or replay detection
being impossible, breaking security properties, as described
in the "KRACK attacks".
In particular, CVE-2017-13080 applies to GTK rekeying that
happened in firmware while the host is in D3, with the second
part of the attack being done after the host wakes up. In
this case, the wpa_supplicant mitigation isn't sufficient
since wpa_supplicant doesn't know the GTK material.
In case this happens, simply silently accept the new key
coming from userspace but don't take any action on it since
it's the same key; this keeps the PN replay counters intact.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- Fix unfortunate mistake in the GICv3 ITS binding example
- Two fixes for the recently merged GICv4 support
- GICv3 ITS 52bit PA fixes
- Generic irqchip mask-ack fix, and its application to the tango irqchip
-----BEGIN PGP SIGNATURE-----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=yAAX
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip updates for 4.14-rc5 from Marc Zyngier:
- Fix unfortunate mistake in the GICv3 ITS binding example
- Two fixes for the recently merged GICv4 support
- GICv3 ITS 52bit PA fixes
- Generic irqchip mask-ack fix, and its application to the tango irqchip
Add device-id entry for (Honeywell) Metrologic MS7820 bar code scanner.
The device has two interfaces (in this mode?); a vendor-specific
interface with two interrupt endpoints and a second HID interface, which
we do not bind to.
Reported-by: Ladislav Dobrovsky <ladislav.dobrovsky@gmail.com>
Tested-by: Ladislav Dobrovsky <ladislav.dobrovsky@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The 'this_leaf' variable is assigned a value that is never
read and it is updated a little later with a newer value,
hence we can remove the redundant assignment.
Cleans up the following Clang warning:
Value stored to 'this_leaf' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kernel-janitors@vger.kernel.org
Link: http://lkml.kernel.org/r/20171015160203.12332-1-colin.king@canonical.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
zipl from s390-tools generates root=/dev/ram0 kernel cmdline for
zfcpdump, thus BLK_DEV_RAM is required.
zfcpdump initrd mounts DEBUG_FS, thus is also required.
Bug-Ubuntu: https://launchpad.net/bugs/1722735
Bug-Ubuntu: https://launchpad.net/bugs/1719290
Signed-off-by: Dimitri John Ledkov <xnox@ubuntu.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
