When we enable a PCI device, we avoid doing a lot of the initial setup
work if the device's enable count is non-zero. If we don't fetch the
power state though, we may later fail to set up MSI due to the unknown
status. So pick it up before we short circuit the rest due to a
pre-existing enable or mismatched enable/disable pair (as happens with
VGA devices, which are special in a special way).
Tested-by: Jesse Brandeburg <jesse.brandeburg@gmail.com>
Reported-by: Dave Airlie <airlied@linux.ie>
Tested-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The checks for valid mmaps of PCI resources made through /proc/bus/pci files
that were introduced in 9eff02e204 have several
problems:
1. mmap() calls on /proc/bus/pci files are made with real file offsets > 0,
whereas under /sys/bus/pci/devices, the start of the resource corresponds
to offset 0. This may lead to false negatives in pci_mmap_fits(), which
implicitly assumes the /sys/bus/pci/devices layout.
2. The loop in proc_bus_pci_mmap doesn't skip empty resouces. This leads
to false positives, because pci_mmap_fits() doesn't treat empty resources
correctly (the calculated size is 1 << (8*sizeof(resource_size_t)-PAGE_SHIFT)
in this case!).
3. If a user maps resources with BAR > 0, pci_mmap_fits will emit bogus
WARNINGS for the first resources that don't fit until the correct one is found.
On many controllers the first 2-4 BARs are used, and the others are empty.
In this case, an mmap attempt will first fail on the non-empty BARs
(including the "right" BAR because of 1.) and emit bogus WARNINGS because
of 3., and finally succeed on the first empty BAR because of 2.
This is certainly not the intended behaviour.
This patch addresses all 3 issues.
Updated with an enum type for the additional parameter for pci_mmap_fits().
Cc: stable@kernel.org
Signed-off-by: Martin Wilck <martin.wilck@ts.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
While testing various randconfigs with ktest.pl, I hit the following panic:
BUG: unable to handle kernel paging request at f7e54b03
IP: [<c0d63409>] ibmphp_access_ebda+0x101/0x19bb
Adding printks, I found that the loop that reads the ebda blocks
can move out of the mapped section.
ibmphp_access_ebda: start=f7e44c00 size=5120 end=f7e46000
ibmphp_access_ebda: io_mem=f7e44d80 offset=384
ibmphp_access_ebda: io_mem=f7e54b03 offset=65283
The start of the iomap was at f7e44c00 and had a size of 5120,
making the end f7e46000. We start with an offset of 0x180 or
384, giving the first read at 0xf7e44d80. Reading that location
yields 65283, which is much bigger than the 5120 that was allocated
and makes the next read at f7e54b03 which is outside the mapped area.
Perhaps this is a bug in the driver, or buggy hardware, but this patch
is more about not crashing my box on start up and just giving a warning
if it detects this error.
This patch at least lets my box boot with just a warning.
Cc: Chandru Siddalingappa <chandru@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
TTY: move .gitignore from drivers/char/ to drivers/tty/vt/
TTY: create drivers/tty/vt and move the vt code there
TTY: create drivers/tty and move the tty core files there
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-next-2.6:
Staging: ath6kl: remove empty files that mess with 'distclean'
staging: ath6kl: Fixing the driver to use modified mmc_host structure
Staging: solo6x10: fix build problem
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: clkfwk: Fix up checkpatch warnings.
sh: make some needlessly global sh7724 clocks static
sh: add clk_round_parent() to optimize parent clock rate
sh: Simplify phys_addr_mask()/PTE_PHYS_MASK for 29/32-bit.
sh: nommu: Support building without an uncached mapping.
sh: nommu: use 32-bit phys mode.
sh: mach-se: Fix up SE7206 no ioport build.
sh: intc: Update for single IRQ reservation helper.
sh: clkfwk: Fix up rate rounding error handling.
sh: mach-se: Rip out superfluous 7751 PIO routines.
sh: mach-se: Rip out superfluous 770x PIO routines.
sh: mach-edosk7705: Kill off machtype, consolidate board def.
sh: mach-edosk7705: update for this century, kill off PIO trapping.
sh: mach-se: Rip out superfluous 7206 PIO routines.
sh: mach-systemh: Kill off dead board.
sh: mach-snapgear: Kill off machtype, consolidate board def.
sh: mach-snapgear: Rip out superfluous PIO routines.
sh: mach-microdev: SuperIO-relative ioport mapping.
Sometimes it is possible and reasonable to adjust the parent clock rate to
improve precision of the child clock, e.g., if the child clock has no siblings.
clk_round_parent() is a new addition to the SH clock-framework API, that
implements such an optimization for child clocks with divisors, taking all
integer values in a range.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These two .h files would get removed from the tree when doing
make distclean
It turns out they are not needed at all, so just delete them which fixes
people's git trees when doing development.
Reported-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While scanning the floopy code due to c093ee4f07 ("floppy: fix
use-after-free in module load failure path"), I found one more instance
of trying to access disk->queue pointer after doing put_disk() on
gendisk. For some reason , floppy moule still loads/unloads fine. The
object is probably still around with right pointer values.
o There seems to be one more instance of trying to cleanup the request
queue after we have called put_disk() on associated gendisk.
o This fix is more out of code inspection. Even without this fix for
some reason I am able to load/unload floppy module without any
issues.
o Floppy module loads/unloads fine after the fix.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The autogenerated files (consolemap_deftbl.c and defkeymap.c) need to
be ignored by git, so move the .gitignore file that was doing it to the
properly location now that the files have moved as well.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 27ae60f8f7 ("ipw2x00: replace "ieee80211" with "libipw" where
appropriate") changed DRV_NAME to be "libipw", but didn't properly fix
up the places where it was used to specify the name for the /proc/net/
directory.
For backwards compatibility reasons, that directory name remained
"ieee80211", but due to the DRV_NAME change, the error case printouts
and the cleanup functions now used "libipw" instead. Which made it all
fail badly.
For example, on module unload as reported by Randy:
WARNING: at fs/proc/generic.c:816 remove_proc_entry+0x156/0x35e()
name 'libipw'
because it's trying to unregister a /proc directory that obviously
doesn't even exist.
Clean it all up to use DRV_PROCNAME for the actual /proc directory name.
Reported-and-tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Pavel Roskin <proski@gnu.org>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 488211844e ("floppy: switch to one queue per drive instead of
sharing a queue") introduced a use-after-free. We do "put_disk()" on
the disk device _before_ we then clean up the queue associated with that
disk.
Move the put_disk() down to avoid dereferencing a free'd data structure.
Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Reported-and-tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (41 commits)
inet_diag: Make sure we actually run the same bytecode we audited.
netlink: Make nlmsg_find_attr take a const nlmsghdr*.
fib: fib_result_assign() should not change fib refcounts
netfilter: ip6_tables: fix information leak to userspace
cls_cgroup: Fix crash on module unload
memory corruption in X.25 facilities parsing
net dst: fix percpu_counter list corruption and poison overwritten
rds: Remove kfreed tcp conn from list
rds: Lost locking in loop connection freeing
de2104x: fix panic on load
atl1 : fix panic on load
netxen: remove unused firmware exports
caif: Remove noisy printout when disconnecting caif socket
caif: SPI-driver bugfix - incorrect padding.
caif: Bugfix for socket priority, bindtodev and dbg channel.
smsc911x: Set Ethernet EEPROM size to supported device's size
ipv4: netfilter: ip_tables: fix information leak to userland
ipv4: netfilter: arp_tables: fix information leak to userland
cxgb4vf: remove call to stop TX queues at load time.
cxgb4: remove call to stop TX queues at load time.
...
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: ohci: fix race when reading count in AR descriptor
firewire: ohci: avoid reallocation of AR buffers
firewire: ohci: fix race in AR split packet handling
firewire: ohci: fix buffer overflow in AR split packet handling
adapter->id is deprecated and not set by any adapter driver, so this
was certainly not what the author wanted to use. adapter->nr maybe,
but as dev_err() already includes this value, as well as the client's
address, there's no point repeating them. Better print a simple error
message in plain English words.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add MODULE_LICENSE() that matches file comments so that kernel
is not tainted.
leds_net5501: module license 'unspecified' taints kernel.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The vt and other related code is moved into the drivers/tty/vt directory.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The tty code should be in its own subdirectory and not in the char
driver with all of the cruft that is currently there.
Based on work done by Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Its now illegal to call netif_stop_queue() before register_netdev()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its now illegal to call netif_stop_queue() before register_netdev()
Reported-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quote from Amit Salecha:
"Actually I was not updated, NX_UNIFIED_ROMIMAGE_NAME (phanfw.bin) is already
submitted and its present in linux-firmware.git.
I will get back to you on NX_P2_MN_ROMIMAGE_NAME, NX_P3_CT_ROMIMAGE_NAME and
NX_P3_MN_ROMIMAGE_NAME. Whether this will be submitted ?"
We have to remove these, otherwise we will get wrong info from modinfo.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Amit Kumar Salecha <amit.salecha@qlogic.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Cc: Narender Kumar <narender.kumar@qlogic.com>
Acked-by: Amit Kumar Salecha <amit.salecha@qlogic.com>--
Signed-off-by: David S. Miller <davem@davemloft.net>
The SMSC911x supports 128 x 8-bit EEPROMs. Increase the EEPROM size
so more than just the MAC address can be stored.
Signed-off-by: John Faith <jfaith7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent change in the mmc_host structure removed the distinction
between hw and phys segments (58cb50c20fde6059f3f8db4466a1bd4d1fff999c)
Changing the driver to use the modified structure.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Vipin Mehta <vmehta@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With commit 08bff03ed6 (V4L/DVB: videobuf:
add ext_lock argument to the queue init functions)
videobuf_queue_sg_init() changed to need another paramater. This patch
fixes that issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stopping TX queues at driver load time is not necessary.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove racy queue stopping after device registration.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove racy queue stopping after device registration.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the linux/clk.h definition we should be handing back an
errno value or a valid rate. This fixes up the case where 0 can be
returned for invalid frequencies or cases where rounding has no
selectable candidate.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Crash is triggered by commit e6484930d7 ("net: allocate tx queues in
register_netdevice"), which moved tx netqueue creation into register_netdev.
So now calling netif_stop_queue() before register_netdev causes an oops.
Move netif_stop_queue() after net device registration to fix crash.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Touching the queue state before register_netdev is not
allowed, and besides the queue state before ->open()
is "don't care"
Reported-by: Josh Boyer <jwboyer@gmail.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since usbnet already took usb runtime pm, we have to
enable runtime pm for usb interface of usbnet, otherwise
usb_autopm_get_interface may return failure and cause
'ifconfig usb0 up' failed if USB_SUSPEND(RUNTIME_PM) is
enabled.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm a bit unsure about this patch. I'm unable to parse both statements.
Cc: netdev@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bnx2x version number.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resetting 8073 during common init is required on boards in which the
8073 reset pin is not asserted by default.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling CL37 BAM on BCM8073 by default may lead to link issues since
not all switches support it. So enable CL37 BAM only if explicitly
selected.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On BCM8726 based designs, the ports are swapped, hence the reset needs
to be asserted through port0 and not port1.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using latch indication for link change notification, need to
clear it when port is unloaded, otherwise it might generate false
indication on next load.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On E2 flavor, dual-port mode, the port argument used for some
functions is needed as the global port number rather than the port per
path.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM848x3 requires additional of 50ms after reset done indication,
instead of fixed time of 200ms
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix delay during BMAC reset from 10usec to 1ms.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi/pl022: fix erroneous platform data in U300
spi: fixed odd static string conventions in core code
spi/bfin_spi: only request GPIO on first load
spi/bfin_spi: handle error/status changes after data interrupts
spi: enable spi_board_info to be registered after spi_master
