Commit af46800 ("ASoC: Implement mux control sharing") revealed that
"Left Line1[L | R] Mux" and "Right Line1[L | R] Mux" widgets were pointing
to the same kcontrols and codec registers and thus soc-core falsely detected
them as shared controls. This is actually wrong since there are separate
registers in hardware that configure Line1L to RADC and Line1R to LADC cross
connects so these muxes should not be shared.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
TLV320AIC33, TLV320AIC34 and I believe others too in this family have some
hw bugs that cause that analogue and digital VDD supplies remain leaking
up to a few mA of current after certain use cases even the hw blocks inside
codec are driven to off.
Highest leakages occur after using the bypass paths inside codec but it
is possible to get smaller leakages just by toggling mute switches in
unused audio paths (i.e. no DAPM changes) while codec is on due another
active audio path.
While some cases are able to workaroud by making sure that e.g. output mixer
switches are muted before powering down the output stage this doesn't help
all the cases.
Therefore use the software reset command to clear possible leakage currents
since that works in every cases and affects only this codec instance. Only
drawback is that now cache sync is required everytime when codec bias comes
out from bias off state, not only when supply regulators were off.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
There is no need to sync first two registers from cache to hw after a reset.
First one is used to select page for register access and this driver is
normally accessing page 0 only. Second one does a software reset which is
obviously unneeded after hardware or previous software reset command.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Commit fafd217 ("ASoC: Store a list of widgets in a DAPM mux/mixer kcontrol")
changed the control private data type that is passed to snd_soc_cnew when
creating dapm mixer and mux controls. Commit did not update a few codec
drivers that are using their own put callbacks and thus are accessing a
wrong data type.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Decoupling DAPM paths from DAPM context is a first prerequisite when
extending ASoC core to cross-device paths. This patch is almost a nullop and
does not allow to construct cross-device setup but the path clean-up part in
dapm_free_widgets is prepared to remove cross-device paths between a device
being removed and others.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If aic3x_read failed , val is used uninitialized.
Fix it by initializing val to 0.
This patch fixes below compile warning:
sound/soc/codecs/tlv320aic3x.c: In function 'aic3x_get_gpio':
sound/soc/codecs/tlv320aic3x.c:1183: warning: 'val' may be used uninitialized in this function
sound/soc/codecs/tlv320aic3x.c: In function 'aic3x_headset_detected':
sound/soc/codecs/tlv320aic3x.c:1211: warning: 'val' may be used uninitialized in this function
sound/soc/codecs/tlv320aic3x.c: In function 'aic3x_button_pressed':
sound/soc/codecs/tlv320aic3x.c:1219: warning: 'val' may be used uninitialized in this function
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no need to include soc-dapm.h since soc.h includes it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We allocated memory for aic3x in aic3x_i2c_probe,
and will free the memory in either aic3x_i2c_probe error path or
aic3x_i2c_remove.
Thus we should not call kfree(aic3x) in aic3x_probe, otherwise
we have double free of aic3x.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Decoupling Dynamic Audio Power Management (DAPM) from codec devices is
required when developing ASoC further. Such as for other ASoC components to
have DAPM widgets or when extending DAPM to handle cross-device paths.
This patch decouples DAPM related variables from struct snd_soc_codec and
moves them to new struct snd_soc_dapm_context that is used to encapsulate
DAPM context of a device. ASoC core and API of DAPM functions are modified
to use DAPM context instead of codec.
This patch does not change current functionality and a large part of changes
come because of structure and internal API changes.
Core implementation is from Liam Girdwood <lrg@slimlogic.co.uk> with some
minor core changes, codecs and machine driver conversions from
Jarkko Nikula <jhnikula@gmail.com>.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Cliff Cai <cliff.cai@analog.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Cc: Timur Tabi <timur@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jassi Brar <jassi.brar@samsung.com>
Cc: Daniel Gloeckner <dg@emlix.com>
Cc: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is aimed to configurations where multiple aic3x codecs share the same
reset line and are powered from same supply voltages.
Currently aic3x_probe will fail if trying to request already requested
gpio_reset and passing -1 to another aic3x instances cause that those
instances cannot release reset in aic3x_set_power. That is, another
instances can work only if primary aic3x instance is powered and reset is
released.
Solve this by implementing a list of probed instances that is used for
checking if other instance shares the same gpio_reset number. If a shared
reset line exists, then only first instance tries to request and configure
it and the last instance releases it.
Runtime modifications are not needed since aic3x_regulator_event with help
of regulator framework takes already care that reset is pulled down only
when some or all supplies are disabled meaning that all instances using them
are idle.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
I promised to convert this at some point.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Now codec hits the SND_SOC_BIAS_OFF also when it is idle. This is also
the default state after probing and codec is left unconfigured and
unpowered by default. Initialization will happen when the bias state changes
and aic3x_set_power does power-up and cache sync.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
There is no need to reset the codec and perform cache sync if none of the
supply regulators were not disabled. Patch registers a notifier callback for
each supply and callback then sets a flag to indicate when cache sync is
required.
HW writes are also needless when codec bias is off so cache_only flag is set
independently of actual supply regulators state.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Now all the regulators are disabled when entering into SND_SOC_BIAS_OFF
and enabled when coming back to SND_SOC_BIAS_STANDBY state. Currently this
runtime control happens only with suspend/resume as this patch does not
change the default idle behavior.
This patch manages all the regulators and reset since it seems that register
sync is needed even if only analog supplies AVDD and DRVDD are disabled.
This was noted when the system was running with idle behavior changed and
IOVDD and DVDD were on.
It is not known are all the registers needed to sync or only some subset of
them. Therefore patch plays safe and does always full shutdown/power-up.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
It will be easier to keep regulator enable/disable calls in sync when dynamic
regulator management is added if regulator management is moved from
aic3x_i2c_probe/_remove to aic3x_probe/_remove.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Purpose of this virtual Detection pin is to keep codec bias on whenever the
GPIO or jack detection features are needed.
Jack detection needs a mic bias so machine drivers can construct a following
route for instance for keeping the path and codec bias on:
"Input Jack" -> "Mic Bias xV" -> "Detection" -> detection block inside codec.
For the GPIO the machine driver can force the pin on with
snd_soc_dapm_force_enable_pin.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Complete the phasing out of aic3x_read_reg_cache, aic3x_write_reg_cache,
aic3x_read and aic3x_write calls.
This patch uses in aic3x_read the codec->hw_read that points to a function
implemented by soc-cache. Only use for aic3x_read is if wanting to read
volatile bits from those registers that has both read-only and read/write
bits. All other cases should use snd_soc_read.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Continue phasing out aic3x_read_reg_cache, aic3x_write_reg_cache, aic3x_read
and aic3x_write calls.
This patch takes the soc-cache in use and removes aic3x_read_reg_cache and
aic3x_write.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Start phasing out aic3x_read_reg_cache, aic3x_write_reg_cache, aic3x_read and
aic3x_write calls in order to switch to soc-cache helpers.
This patch replaces aic3x_read_reg_cache and aic3x_write with snd_soc_read
and snd_soc_write. This is basically null-op since .read and .write in
soc_codec_dev_aic3x points to aic3x_read_reg_cache and aic3x_write.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
There is only need to enable/disable once the PLL when the bias is going
between on, prepare, standby and off states.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Null pointer dereference will occur from *setup = pdata->setup if pdata
is not set. Fix this by moving assignments from pdata inside non-null case.
Thanks to Jiri Slaby <jirislaby@gmail.com> for noticing.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently output controls are not uniform. Some routes are adjusted by
mono controls that don't match to associated mixer switch, many routes are
not covered at all and stereo controls have following variants:
- L-to-L & R-to-R
- R-to-L & R-to-R
- L-to-L & R-to-L
This patch attempts to fix these issues. First, for the convenience, only
direct L-to-L, R-to-R and [L | R]-to-Mono routes are controlled by the
stereo controls. This logic is also used with the output pin mute controls
so all of them except mono output are controlled by stereo switches.
Then rest of the swapped L-to-R and R-to-L routes are controlled by the
mono controls that map to mixer switches with a same name. Mixers can then
associate these switches and volumes together.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
It turned out that the output mixers and their routes were misdefined: They
are not mixing output pins to internal signals but opposite. This has worked
for direct left-to-left and right-to-right routes since for those there are
complete routes. For swapped left-to-right and right-to-left routes this is
not working since there are no routes defined between them.
Another consequence is that those misdefined mixers are incorrectly routed
to several output pins leading unnecessary pin powerings even if there is no
route active to them.
Fix these by reimplementing the output mixers and routes as they are in
hardware. For completeness add also a few missing links between internal
signals and outputs.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Bit 3 in output pin_CTRL register mutes the whole output pin not just the
route from DAC so remove misleading DAC from control name. Currently only
"Line[L | R] Playback Switch" were correct.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
aic3x_init does a soft reset first and thus TLV320AIC3x GPIO setup must be
done after doing the basic init. Before multi-component the init was done
at i2c probe time and GPIO setup at soc probe time.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds support for the tlv320aic3007 codec to the tlv320aic3x
driver.
The tlv320aic3007 is similar to the aic31, but has an additional class-D
speaker amp. The speaker amp control register overlaps with the mono
output register of other codecs in this family, so we add logic to
identify the actual codec being registered to set things up accordingly.
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The tlv320aic3x codec driver only supports symmetric rates for capture/
playback. Set the flag in the DAI accordingly.
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch extends the ASoC API to allow sound cards to have more than one
CODEC and more than one platform DMA controller. This is achieved by dividing
some current ASoC structures that contain both driver data and device data into
structures that only either contain device data or driver data. i.e.
struct snd_soc_codec ---> struct snd_soc_codec (device data)
+-> struct snd_soc_codec_driver (driver data)
struct snd_soc_platform ---> struct snd_soc_platform (device data)
+-> struct snd_soc_platform_driver (driver data)
struct snd_soc_dai ---> struct snd_soc_dai (device data)
+-> struct snd_soc_dai_driver (driver data)
struct snd_soc_device ---> deleted
This now allows ASoC to be more tightly aligned with the Linux driver model and
also means that every ASoC codec, platform and (platform) DAI is a kernel
device. ASoC component private data is now stored as device private data.
The ASoC sound card struct snd_soc_card has also been updated to store lists
of it's components rather than a pointer to a codec and platform. The PCM
runtime struct soc_pcm_runtime now has pointers to all its components.
This patch adds DAPM support for ASoC multi-component and removes struct
snd_soc_socdev from DAPM core. All DAPM calls are now made on a card, codec
or runtime PCM level basis rather than using snd_soc_socdev.
Other notable multi-component changes:-
* Stream operations now de-reference less structures.
* close_delayed work() now runs on a DAI basis rather than looping all DAIs
in a card.
* PM suspend()/resume() operations can now handle N CODECs and Platforms
per sound card.
* Added soc_bind_dai_link() to bind the component devices to the sound card.
* Added soc_dai_link_probe() and soc_dai_link_remove() to probe and remove
DAI link components.
* sysfs entries can now be registered per component per card.
* snd_soc_new_pcms() functionailty rolled into dai_link_probe().
* snd_soc_register_codec() now does all the codec list and mutex init.
This patch changes the probe() and remove() of the CODEC drivers as follows:-
o Make CODEC driver a platform driver
o Moved all struct snd_soc_codec list, mutex, etc initialiasation to core.
o Removed all static codec pointers (drivers now support > 1 codec dev)
o snd_soc_register_pcms() now done by core.
o snd_soc_register_dai() folded into snd_soc_register_codec().
CS4270 portions:
Acked-by: Timur Tabi <timur@freescale.com>
Some TLV320aic23 and Cirrus platform fixes.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
TI CODEC and OMAP fixes
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Samsung platform and misc fixes :-
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
MPC8610 and PPC fixes.
Signed-off-by: Timur Tabi <timur@freescale.com>
i.MX fixes and some core fixes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
J4740 platform fixes:-
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
CC: Tony Lindgren <tony@atomide.com>
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
CC: Kuninori Morimoto <morimoto.kuninori@renesas.com>
CC: Daniel Gloeckner <dg@emlix.com>
CC: Manuel Lauss <mano@roarinelk.homelinux.net>
CC: Mike Frysinger <vapier.adi@gmail.com>
CC: Arnaud Patard <apatard@mandriva.com>
CC: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The core will ensure that the device is in either STANDBY or OFF bias
before suspending, restoring the bias in the driver is unneeded. Some
drivers doing slightly more roundabout things have been left alone
for now.
Tested-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Handle the reset GPIO within the codec driver in order to follow
the startup protocol for the tlv320aic3x codecs.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds the TLV320AIC3x supplies and enables all of them for the
entire lifetime of the device.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Move PLL enable from BIAS_ON state to BIAS_PREPARE to be pair with
BIAS_STANDBY where PLL is disabled. Remove also old comments about power
control.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
These ADC, DAC and output pin power off commands are needless in
aic3x_set_bias_level since they are not enabled in aic3x_init and they are
defined in aic3x_dapm_widgets so the ASoC DAPM will take care of them
anyway.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
One of the features of the multi CODEC work is that it embeds a struct
device in the CODEC to provide diagnostics via a sysfs class rather than
via the device tree, at which point it's much better to use the struct
device private data rather than having two places to store it. Provide
an accessor function to allow this change to be made more easily, and
update all the CODEC drivers are updated.
To ensure use of the accessor the private data structure member is
renamed, meaning that if code developed with older an older core that
still uses private_data is merged it will fail to build.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
fix precision of PLL computation for TLV320AIC3x SoC driver,
test results are at http://pmeerw.net/clk
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Acked-by: Vladimir Barinov <vova.barinov@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DAPM widgets are now insntantiated by the core when creating the card
so there is no need for the individual CODEC drivers to do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_soc_init_card() is always called as the last part of the CODEC probe
function so we can factor it out into the core card setup rather than
have each CODEC replicate the code to do the initialiastation. This will
be required to support multiple CODECs per card.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
