The elan touchscreen datasheet says that the reset GPIO only needs to
be asserted for 500us in order to reset the regulator. The problem is
that some boards need a level shifter between the signals on the GPIO
controller and the signals on the touchscreen. All of these extra
components on the line can slow the transition of the signals. On one
board, we measured the reset line and saw that it took almost 1.8ms to
go low. Even after we bumped up the "drive strength" of the signal
from the default 2mA to 8mA we still saw it take 421us for the signal
to go low.
In order to account for this let's lengthen the amount of time that we
keep the reset asserted. Let's bump it up from 500us to 5000us.
That's still a relatively short amount of time and is much safer.
It should be noted that this fixes real problems. Case in point:
1. The touchscreen power rail may be shared with another device (like
an eDP panel). That means that at probe time power might already be
on.
2. In probe we grab the reset GPIO and assert it (make it low).
3. We turn on power (a noop since it was already on).
4. We wait 500us.
5. We deassert the reset GPIO.
With the above case and only a 500us delay we saw only a partial reset
asserted, which is bad. Giving it 5ms is overkill but feels safer in
case someone else has a different level shifter setup.
Note that bumping up the delay to 5000 means that some configs yell
about using udelay(). We'll change to using usleep_range(). We give a
small range here because:
- This isn't a delay that happens very often so we don't need to worry
about giving a big range to allow for power efficiency.
- usleep_range() is known to almost always pick the upper bound and
delay that long and we really don't want to slow down the power on
of the touchscreen that much.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20221208180603.v2.5.I6edfb3f459662c041563a54e5b7df727c27caaba@changeid
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-268-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-267-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-266-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/20221118224540.619276-265-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-264-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-263-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-262-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-261-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-260-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-259-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221118224540.619276-258-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-257-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-256-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-255-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-254-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-253-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-252-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-251-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-250-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-249-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20221118224540.619276-248-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-247-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-246-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-245-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-244-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-243-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221118224540.619276-242-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-241-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-240-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-239-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oliver Graute <oliver.graute@kococonnector.com>
Link: https://lore.kernel.org/r/20221118224540.619276-238-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-237-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-236-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-235-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-234-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-233-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221118224540.619276-232-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-231-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-230-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20221118224540.619276-229-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-228-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-227-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-226-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The linux,keycodes property is optional.
Fix the driver not probing when it's not specified.
Fixes: c18ef50346 ("Input: msg2638 - add support for msg2138 key events")
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Link: https://lore.kernel.org/r/20221130210202.2069213-1-vincent.knecht@mailoo.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We shuffled the error handling around so this condition is dead code
now. The "error" variable is always zero.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/Y33BD9xkRC9euIdO@kili
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20221121145203.1efb0c08@endymion.delvare
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry Torokhov