There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210409075224.2109503-1-yebin10@huawei.com
Use thermal_zone_device_{en|dis}able() and thermal_zone_device_is_enabled().
Consequently, all set_mode() implementations in drivers:
- can stop modifying tzd's "mode" member,
- shall stop taking tzd's lock, as it is taken in the helpers
- shall stop calling thermal_zone_device_update() as it is called in the
helpers
- can assume they are called when the mode truly changes, so checks to
verify that can be dropped
Not providing set_mode() by a driver no longer prevents the core from
being able to set tzd's mode, so the relevant check in mode_store() is
removed.
Other comments:
- acpi/thermal.c: tz->thermal_zone->mode will be updated only after we
return from set_mode(), so use function parameter in thermal_set_mode()
instead, no need to call acpi_thermal_check() in set_mode()
- thermal/imx_thermal.c: regmap writes and mode assignment are done in
thermal_zone_device_{en|dis}able() and set_mode() callback
- thermal/intel/intel_quark_dts_thermal.c: soc_dts_{en|dis}able() are a
part of set_mode() callback, so they don't need to modify tzd->mode, and
don't need to fall back to the opposite mode if unsuccessful, as the return
value will be propagated to thermal_zone_device_{en|dis}able() and
ultimately tzd's member will not be changed in thermal_zone_device_set_mode().
- thermal/of-thermal.c: no need to set zone->mode to DISABLED in
of_parse_thermal_zones() as a tzd is kzalloc'ed so mode is DISABLED anyway
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
[for acerhdf]
Acked-by: Peter Kaestle <peter@piie.net>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-8-andrzej.p@collabora.com
Without this patch the thermal driver is broken on hi3660.
The dual sensors support patchset was partially merged, unfortunately
the dual thermal zones definition is not available in the DT yet, so
when the driver tries to register all the sensors that fails.
By reducing to 1 the number of sensors on the hi3660, we switch back
to the previous functionnality.
Fixes: 8c6c36846f (thermal/drivers/hisi: Add the dual clusters sensors for hi3660)
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Without this patch, the thermal driver on hi6220 and hi3660 is broken.
That is due because part of the posted patchset was merged but a small
change in the DT was dropped.
The hi6220 and hi3660 do not have an interrupt name in the DT, so
finding interrupt by name fails.
Fix this by returning back to the platform_get_irq() function call.
Fixes: 2cffaeff08 (thermal/drivers/hisi: Use platform_get_irq_byname)
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The code is ready to support multiple sensors on the hi3660. The DT
defines a thermal zone per cluster.
Add the little cluster sensor and let it bind with the thermal zone.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add the sensor channels id for the little, g3d and modem.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The irq field in the data structure is pointless as the scope of its
usage is just to request the interrupt. It can be replaced by a local
variable.
Use the 'ret' variable to get the interrupt number.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As we have the interrupt names defines, replace platform_get_irq() by
platform_get_irq_byname(), so no confusion can be made when getting
the interrupt with the sensor id.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Change the macro name in order to give a better indication of the
sensor location.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Change the code as it is dealing with several sensors.
For git-bisect compatibility (compilation and booting), assume the DT
is not yet changed and we have a single interrupt.
Next changes will support multiple interrupt sorted by their name.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Convert the 'sensor' field to a pointer and propagate the change in
the file. Havintg a pointer, gives us the opportunity to define
multiple sensors.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The hi6220 and the hi3660 probe functions are doing almost the same
operations, they can share 90% of their code.
Factor out the probe functions by moving the common code in the common
probe function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Store the sensor pointer in the thermal zone private data and use it
in the callback functions. That allows to continue the conversion to
sensor oriented code where the pointers are the sensors.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In order to support multiple sensors, we have to change the code to
deal with sensors and not the hisi thermal structure.
Add a back pointer to the hisi thermal structure (containerof is not a
good option because later we convert the sensor field to a pointer).
Change the functions parameters to take a sensor instead of this hisi
thermal 'data' structure.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Group the temperature sensor specific ops into a single structure and
assign it to hisi thermal data structure.
Change the platform data pointer to reference the specific sensor ops
instead of the probe functions.
Moving out those allow to split the code to self-encapsulate the
sensor object.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
With gcc-4.1.2:
drivers/thermal/hisi_thermal.c: In function ‘hisi_thermal_probe’:
drivers/thermal/hisi_thermal.c:530: warning: type qualifiers ignored on function return type
Remove the "const" keyword to fix this.
Fixes: a160a46529 ("thermal/drivers/hisi: Prepare to add support for other hisi platforms")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch adds the support for thermal sensor on the Hi3660 SoC.
Hi3660 tsensor support alarm in alarm threshold, it also has a configurable
hysteresis interval, interrupt will be triggered when temperature rise above
the alarm threshold or fall below the hysteresis threshold.
Signed-off-by: Kevin Wangtao <kevin.wangtao@linaro.org>
Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org> # hikey6220
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
For platform compatibility, add the tsensor ops to a thermal data
structure. Each platform has its own probe function to register proper
tsensor ops function to the pointer, platform related resource request
are also implemented in the platform probe function.
Signed-off-by: Kevin Wangtao <kevin.wangtao@linaro.org>
Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org> # hikey6220
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As the next patches will provide support for the hikey3660's sensor,
several functions with the same purpose but for different platforms will
be introduced.
In order to make a clear distinction between them, let's prefix the
function names with the platform name.
This patch has no functional changes, only name changes.
Signed-off-by: Kevin Wangtao <kevin.wangtao@linaro.org>
Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org> # hikey6220
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Reorganize the code for next patches by moving the functions upper in
the file which will prevent a forward declaration. There is no functional
change here.
Signed-off-by: Kevin Wangtao <kevin.wangtao@linaro.org>
Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org> # hikey6220
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Use round up division to ensure the programmed value of threshold and the lag
are not less than what we set, and in order to keep the accuracy while using
round up division, the step value should be a rounded up value. There is
no need to use hisi_thermal_round_temp.
Signed-off-by: Kevin Wangtao <kevin.wangtao@linaro.org>
Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org> # hikey6220
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The sensor's clock is enabled and disabled outside of the probe and
disable function. Moving the corresponding action in the
hisi_thermal_setup() and hisi_thermal_disable_sensor(), factors out
some lines of code and makes the code more symmetric.
Signed-off-by: Kevin Wangtao <kevin.wangtao@linaro.org>
Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org> # hikey6220
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The mutex is used to protect against writes in the configuration register.
That happens at probe time, with no possible race yet.
Then when the module is unloaded and at suspend/resume.
When the module is unloaded, it is an userspace operation, thus via a process.
Suspending the system goes through the freezer to suspend all the tasks
synchronously before continuing. So it is not possible to hit the suspend ops
in this driver while we are unloading it.
The resume is the same situation than the probe.
In other words, even if there are several places where we write the
configuration register, there is no situation where we can write it at the same
time, so far as I can judge
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The presence of the thermal data pointer in the sensor structure has the unique
purpose of accessing the thermal data in the interrupt handler.
The sensor pointer is passed when registering the interrupt handler, replace the
cookie by the thermal data pointer, so the back pointer is no longer needed.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There is no point to specify the temperature as long variable, the int is
enough.
Replace all long variables to int, so making the code consistent.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Rename the 'sensors' field to 'sensor' as we describe only one sensor.
Remove the 'sensor_temp' as it is no longer used.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The sensor is all setup, bind, resetted, acked, etc... every single second.
That was the way to workaround a problem with the interrupt bouncing again and
again.
With the following changes, we fix all in one:
- Do the setup, one time, at probe time
- Add the IRQF_ONESHOT, ack the interrupt in the threaded handler
- Remove the interrupt handler
- Set the correct value for the LAG register
- Remove all the irq_enabled stuff in the code as the interruption
handling is fixed
- Remove the 3ms delay
- Reorder the initialization routine to be in the right order
It ends up to a nicer code and more efficient, the 3-5ms delay is removed from
the get_temp() path.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The TEMP0_CFG configuration register contains different field to set up the
temperature controller. However in the code, nothing prevents a setup to
overwrite the previous one: eg. writing the hdak value overwrites the sensor
selection, the sensor selection overwrites the hdak value.
In order to prevent such thing, use a regmap-like mechanism by reading the
value before, set the corresponding bits and write the result.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Hopefully, the function name can help to clarify the semantic of the operations
when writing in the register.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The threaded interrupt inspect the sensors structure to look in the temp
threshold field, but this field is read-only in all the code, except in the
probe function before the threaded interrupt is set. In other words there
is not race window in the threaded interrupt when reading the field value.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The DT specifies a threshold of 65000, we setup the register with a value in
the temperature resolution for the controller, 64656.
When we reach 64656, the interrupt fires, the interrupt is disabled. Then the
irq thread runs and calls thermal_zone_device_update() which will call in turn
hisi_thermal_get_temp().
The function will look if the temperature decreased, assuming it was more than
65000, but that is not the case because the current temperature is 64656
(because of the rounding when setting the threshold). This condition being
true, we re-enable the interrupt which fires immediately after exiting the irq
thread. That happens again and again until the temperature goes to more than
65000.
Potentially, there is here an interrupt storm if the temperature stabilizes at
this temperature. A very unlikely case but possible.
In any case, it does not make sense to handle dozens of alarm interrupt for
nothing.
Fix this by rounding the threshold value to the controller resolution so the
check against the threshold is consistent with the one set in the controller.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The step and the base temperature are fixed values, we can simplify the
computation by converting the base temperature to milli celsius and use a
pre-computed step value. That saves us a lot of mult + div for nothing at
runtime.
Take also the opportunity to change the function names to be consistent with
the rest of the code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The threaded interrupt for the alarm interrupt is requested before the
temperature controller is setup. This one can fire an interrupt immediately
leading to a kernel panic as the sensor data is not initialized.
In order to prevent that, move the threaded irq after the Tsensor is setup.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
By essence, the tsensor does not really support multiple sensor at the same
time. It allows to set a sensor and use it to get the temperature, another
sensor could be switched but with a delay of 3-5ms. It is difficult to read
simultaneously several sensors without a big delay.
Today, just one sensor is used, it is not necessary to deal with multiple
sensors in the code. Remove them and if it is needed in the future add them
on top of a code which will be clean up in the meantime.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Wangtao (Kevin, Kirin) <kevin.wangtao@hisilicon.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The interrupt for the temperature threshold is not enabled at the end of the
probe function, enable it after the setup is complete.
On the other side, the irq_enabled is not correctly set as we are checking if
the interrupt is masked where 'yes' means irq_enabled=false.
irq_get_irqchip_state(data->irq, IRQCHIP_STATE_MASKED,
&data->irq_enabled);
As we are always enabling the interrupt, it is pointless to check if
the interrupt is masked or not, just set irq_enabled to 'true'.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The thermal_zone_of_device_ops structure is only passed as the fourth
argument to devm_thermal_zone_of_sensor_register, which is declared
as const. Thus the thermal_zone_of_device_ops structure itself can
be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Added one additional parameter to thermal_zone_device_update() to provide
caller with an optional capability to specify reason.
Currently this event is used by user space governor to trigger different
processing based on event code. Also it saves an additional call to read
temperature when the event is received.
The following events are cuurently defined:
- Unspecified event
- New temperature sample
- Trip point violated
- Trip point changed
- thermal device up and down
- thermal device power capability changed
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
When register sensors into thermal zone during initialization phase, it
reports error for IRQ imbalance enabling:
[ 2.040713] WARNING: at kernel/irq/manage.c:513
[ 2.040719] Modules linked in:
[ 2.040721]
[ 2.040729] CPU: 1 PID: 804 Comm: irq/33-hisi_the Not tainted 4.5.0-rc4+ #505
[ 2.040732] Hardware name: HiKey Development Board (DT)
[ 2.040736] task: ffffffc03ae82580 ti: ffffffc0379c8000 task.ti: ffffffc0379c8000
[ 2.040745] PC is at __enable_irq+0x74/0x84
[ 2.040749] LR is at __enable_irq+0x74/0x84
This warning is for IRQ imbalance enabling, which is caused by
enable_irq() twice. During sensor's initialization it tries to enable
IRQ, the driver will call thermal_zone_of_sensor_register() to bind
sensors and read sensor's temperature. But at this moment the flag
"data->irq_enabled" has been not initialized as correct state, so it
finally introduces the function enabled_irq() to be called twice. In
essentially this is caused by the flag "data->irq_enabled" is
inconsistent with real hardware IRQ enabling state.
So this patch is to fix this issue, firstly init "irq_enabled" flag
before binding sensors to thermal zone. Also change to use the function
irq_get_irqchip_state() to read back real interrupt line state.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In current code sensor driver registers all 4 sensors together and if
any of them has not bound to thermal zone successfully then driver will
return failure for driver's initialization. As a result, if DT binds
thermal zone with only one sensor, then the thermal driver will not work
well anymore.
So this patch is to fix this issue. It allows the thermal sensor driver
can register any number sensors at initialization phase, and fix up code
for other related code to skip related sensor's accessing if the sensor
has not been enabled in initialization phase.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When calculate temperature, old code firstly do division and then
convert to "millicelsius" unit. This will lose resolution and only can
read back temperature with "Celsius" unit.
So firstly scale step value to "millicelsius" and then do division, so
finally we can increase resolution for temperature value. Also refine
the calculation from temperature value to step value.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The thermal code uses int, long and unsigned long for temperatures
in different places.
Using an unsigned type limits the thermal framework to positive
temperatures without need. Also several drivers currently will report
temperatures near UINT_MAX for temperatures below 0°C. This will probably
immediately shut the machine down due to overtemperature if started below
0°C.
'long' is 64bit on several architectures. This is not needed since INT_MAX °mC
is above the melting point of all known materials.
Consistently use a plain 'int' for temperatures throughout the thermal code and
the drivers. This only changes the places in the drivers where the temperature
is passed around as pointer, when drivers internally use another type this is
not changed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Peter Feuerer <peter@piie.net>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Peter Feuerer <peter@piie.net>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-acpi@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: lm-sensors@lm-sensors.org
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds the support for hisilicon thermal sensor, within
hisilicon SoC. there will register sensors for thermal framework
and use device tree to bind cooling device.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: kongxinwei <kong.kongxinwei@hisilicon.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
