Similar to what happened whith autosuspend, a deadlock has been
reported with PM-runtime accounting in the call path:
change_clocksource
...
write_seqcount_begin
...
timekeeping_update
...
sh_cmt_clocksource_enable
...
rpm_resume
update_pm_runtime_accounting
ktime_get
do
read_seqcount_begin
while read_seqcount_retry
....
write_seqcount_end
Make PM-runtime accounting use ktime_get_mono_fast_ns() to avoid this
problem.
With ktime_get_mono_fast_ns(), the timestamp is not guaranteed to be
monotonic across an update of timekeeping and as a result time can go
backward. Add a test to skip accounting for such situation which should
stay exceptional.
Fixes: a08c2a5a31 ("PM-runtime: Replace jiffies-based accounting with ktime-based accounting")
Reported-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
[ rjw: Subject, changelog, comment cleanup ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pm_runtime_autosuspend_expiration calls ktime_get_mono_fast_ns()
even when its returned value may be unused. Therefore get the
current time later and remove gotos while there.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Calling rpm_put_suppliers() from pm_runtime_drop_link() is excessive
as it affects all suppliers of the consumer device and not just the
one pointed to by the device link being dropped. Worst case it may
cause the consumer device to stop working unexpectedly. Moreover, in
principle it is racy with respect to runtime PM of the consumer
device.
To avoid these problems drop runtime PM references on the particular
supplier pointed to by the link in question only and do that after
the link has been dropped from the consumer device's list of links to
suppliers, which is in device_link_free().
Fixes: a0504aecba ("PM / runtime: Drop usage count for suppliers at device link removal")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit ead18c23c2 ("driver core: Introduce device links
reference counting"), if there is a link between the given supplier
and the given consumer already, device_link_add() will refcount it
and return it unconditionally without updating its flags. It is
possible, however, that the second (or any subsequent) caller of
device_link_add() for the same consumer-supplier pair will pass
DL_FLAG_PM_RUNTIME, possibly along with DL_FLAG_RPM_ACTIVE, in flags
to it and the existing link may not behave as expected then.
First, if DL_FLAG_PM_RUNTIME is not set in the existing link's flags
at all, it needs to be set like during the original initialization of
the link.
Second, if DL_FLAG_RPM_ACTIVE is passed to device_link_add() in flags
(in addition to DL_FLAG_PM_RUNTIME), the existing link should to be
updated to reflect the "active" runtime PM configuration of the
consumer-supplier pair and extra care must be taken here to avoid
possible destructive races with runtime PM of the consumer.
To that end, redefine the rpm_active field in struct device_link
as a refcount, initialize it to 1 and make rpm_resume() (for the
consumer) and device_link_add() increment it whenever they acquire
a runtime PM reference on the supplier device. Accordingly, make
rpm_suspend() (for the consumer) and pm_runtime_clean_up_links()
decrement it and drop runtime PM references to the supplier
device in a loop until rpm_active becones 1 again.
Fixes: ead18c23c2 ("driver core: Introduce device links reference counting")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the device specific version of the async_schedule commands to defer
various tasks related to power management. By doing this we should see a
slight improvement in performance as any device that is sensitive to
latency/locality in the setup will now be initializing on the node closest
to the device.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace jiffies-based accounting for runtime_active_time and
runtime_suspended_time with ktime-based accounting. This makes the
runtime debug counters inline with genpd and other PM subsytems which
use ktime-based accounting.
Timekeeping is initialized before driver_init(). It's only at that time
that PM-runtime can be enabled.
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
[switch from ktime to raw nsec]
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Initializing accounting_timestamp to something different from 0 during
pm_runtime_init() doesn't make sense and puts an artificial ordering
constraint between timekeeping_init() and pm_runtime_init().
PM-runtime should start time accounting only when it is enabled and
discard the period when disabled.
Set accounting_timestamp to now when enabling PM-runtime.
Suggested-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A deadlock has been seen when swicthing clocksources which use
PM-runtime. The call path is:
change_clocksource
...
write_seqcount_begin
...
timekeeping_update
...
sh_cmt_clocksource_enable
...
rpm_resume
pm_runtime_mark_last_busy
ktime_get
do
read_seqcount_begin
while read_seqcount_retry
....
write_seqcount_end
Although we should be safe because we haven't yet changed the
clocksource at that time, we can't do that because of seqcount
protection.
Use ktime_get_mono_fast_ns() instead which is lock safe for such
cases.
With ktime_get_mono_fast_ns, the timestamp is not guaranteed to be
monotonic across an update and as a result can goes backward.
According to update_fast_timekeeper() description: "In the worst
case, this can result is a slightly wrong timestamp (a few
nanoseconds)". For PM-runtime autosuspend, this means only that
the suspend decision may be slightly suboptimal.
Fixes: 8234f6734c ("PM-runtime: Switch autosuspend over to using hrtimers")
Reported-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This brings the kernel doc in line with the function signature.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
clk_prepare() can fail, so check its status and if it fails,
issue an error message and change the clock_entry_status to
PCE_STATUS_ERROR.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some drivers (like i915/drm) needs to get the accounted suspended time.
pm_runtime_suspended_time() will return the suspended accounted time
in ns unit.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cast autosuspend_delay to u64 to make sure that the full computation
of 'expires' or slack will be done in u64, even on 32bits arch.
Otherwise, any delay greater than 2^31 nsec can overflow if signed
32bits is used when converting delay from msec to nsec.
Fixes: 8234f6734c (PM-runtime: Switch autosuspend over to using hrtimers)
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PM-runtime now uses the hrtimers infrastructure for autosuspend, however
comments still reference 'jiffies'.
Fixes: 8234f6734c (PM-runtime: Switch autosuspend over to using hrtimers)
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Devfreq framework supports suspend of its devices.
Call the the devfreq interface and allow devfreq devices
preserve/restore their states during suspend/resume.
Suggested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Subsystem:
- new %ptR printk format
- rename core files
- allow registration of multiple nvmem devices
New driver:
- i.MX system controller RTC
Drivers:
- abx80x: handle voltage ioctls, correct binding doc
- m41t80: correct month in alarm reads
- pcf85363: add pcf85263 support
- pcf8523: properly handle battery low flag
- s3c: limit alarm to one year in the future as ALMYEAR is broken
- sun6i: rework clock output binding
-----BEGIN PGP SIGNATURE-----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=5He5
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- new %ptR printk format
- rename core files
- allow registration of multiple nvmem devices
New driver:
- i.MX system controller RTC
Driver updates:
- abx80x: handle voltage ioctls, correct binding doc
- m41t80: correct month in alarm reads
- pcf85363: add pcf85263 support
- pcf8523: properly handle battery low flag
- s3c: limit alarm to one year in the future as ALMYEAR is broken
- sun6i: rework clock output binding"
* tag 'rtc-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (54 commits)
rtc: rename core files
rtc: nvmem: fix possible use after free
rtc: add i.MX system controller RTC support
dt-bindings: fsl: scu: add rtc binding
rtc: pcf2123: Add Microcrystal rv2123
rtc: class: reimplement devm_rtc_device_register
rtc: enforce rtc_timer_init private_data type
rtc: abx80x: Implement RTC_VL_READ,CLR ioctls
rtc: pcf85363: Add support for NXP pcf85263 rtc
dt-bindings: rtc: pcf85363: Document pcf85263 real-time clock
rtc: pcf8523: don't return invalid date when battery is low
dt-bindings: rtc: use a generic node name for ds1307
PM: Switch to use %ptR
m68k/mac: Switch to use %ptR
Input: hp_sdc_rtc - Switch to use %ptR
rtc: tegra: Switch to use %ptR
rtc: s5m: Switch to use %ptR
rtc: s3c: Switch to use %ptR
rtc: rx8025: Switch to use %ptR
rtc: rx6110: Switch to use %ptR
...
We already have the DEFINE_SHOW_ATTRIBUTE, There is no need to define
such a macro, so remove define_genpd_open_function and
define_genpd_debugfs_fops.
Convert them to DEFINE_SHOW_ATTRIBUTE.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PM-runtime uses the timer infrastructure for autosuspend. This implies
that the minimum time before autosuspending a device is in the range
of 1 tick included to 2 ticks excluded
-On arm64 this means between 4ms and 8ms with default jiffies
configuration
-And on arm, it is between 10ms and 20ms
These values are quite high for embedded systems which sometimes want
the duration to be in the range of 1 ms.
It is possible to switch autosuspend over to using hrtimers to get
finer granularity for short durations and take advantage of slack to
retain some margins and get long timeouts with minimum wakeups.
On an arm64 platform that uses 1ms for autosuspending timeout of its
GPU, idle power is reduced by 10% with hrtimer.
The latency impact on arm64 hikey octo cores is:
- mark_last_busy: from 1.11 us to 1.25 us
- rpm_suspend: from 15.54 us to 15.38 us
[Only the code path of rpm_suspend() that starts hrtimer has been
measured.]
arm64 image (arm64 default defconfig) decreases by around 3KB
with following details:
$ size vmlinux-timer
text data bss dec hex filename
12034646 6869268 386840 19290754 1265a82 vmlinux
$ size vmlinux-hrtimer
text data bss dec hex filename
12030550 6870164 387032 19287746 1264ec2 vmlinux
The latency impact on arm 32bits snowball dual cores is :
- mark_last_busy: from 0.31 us usec to 0.77 us
- rpm_suspend: from 6.83 us to 6.67 usec
The increase of the image for snowball platform that I used for
testing performance impact, is neglictable (244B).
$ size vmlinux-timer
text data bss dec hex filename
7157961 2119580 264120 9541661 91981d build-ux500/vmlinux
size vmlinux-hrtimer
text data bss dec hex filename
7157773 2119884 264248 9541905 919911 vmlinux-hrtimer
And arm 32bits image (multi_v7_defconfig) increases by around 1.7KB
with following details:
$ size vmlinux-timer
text data bss dec hex filename
13304443 6803420 402768 20510631 138f7a7 vmlinux
$ size vmlinux-hrtimer
text data bss dec hex filename
13304299 6805276 402768 20512343 138fe57 vmlinux
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently a genpd only handles the performance state requirements from
the devices under its control. This commit extends that to also handle
the performance state requirement(s) put on the master genpd by its
sub-domains. There is a separate value required for each master that
the genpd has and so a new field is added to the struct gpd_link
(link->performance_state), which represents the link between a genpd and
its master. The struct gpd_link also got another field
prev_performance_state, which is used by genpd core as a temporary
variable during transitions.
On a call to dev_pm_genpd_set_performance_state(), the genpd core first
updates the performance state of the masters of the device's genpd and
then updates the performance state of the genpd. The masters do the same
and propagate performance state updates to their masters before updating
their own. The performance state transition from genpd to its master is
done with the help of dev_pm_opp_xlate_performance_state(), which looks
at the OPP tables of both the domains to translate the state.
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Separate out _genpd_set_performance_state() and
_genpd_reeval_performance_state() from
dev_pm_genpd_set_performance_state() to handle performance state update
related stuff. This will be used by a later commit.
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
dev_pm_genpd_set_performance_state() will be required to call
dev_pm_opp_xlate_performance_state() going forward to translate from
performance state of a sub-domain to performance state of its master.
And dev_pm_opp_xlate_performance_state() needs pointers to the OPP
tables of both genpd and its master.
Lets fetch and save them while the OPP tables are added. Fetching the
OPP tables should never fail as we just added the OPP tables and so add
a WARN_ON() for such a bug instead of full error paths.
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
It's quite questionable whether genpd internally should care about if the
corresponding PM domain for a device is powered on, as to allow setting a
new performance state for it. The assumptions creates an unnecessary
limitation at this point, for both consumers and providers, but more
importantly it also makes the code more complicated.
Therefore, let's simplify the code to allow setting a performance state, by
invoking the ->set_performance_state() callback, no matter whether the PM
domain is powered on or off.
Do note, this change means genpd providers needs to restore the performance
state themselves during power on, via the ->power_on() callback. Moreover,
they may also need to check that the PM domain is powered on, from their
->set_performance_state() callback, before deciding to update the state.
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Cc: linux-pm@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The OPP core already has the performance state values for each of the
genpd's OPPs and there is no need to call the genpd callback again to
get the performance state for the case where the end device doesn't have
an OPP table and has the "required-opps" property directly in its node.
This commit renames of_genpd_opp_to_performance_state() as
of_get_required_opp_performance_state() and moves it to the OPP core, as
it is all about OPP stuff now.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The OPP core currently stores the performance state in the consumer
device's OPP table, but that is going to change going forward and
performance state will rather be set directly in the genpd's OPP table.
For that we need to get the performance state for genpd's device
structure (genpd->dev) instead of the consumer device's structure. Add a
new helper to do that.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
There are several struct device instances that genpd core handles. The
most common one is the consumer device structure, which is named
(correctly) as "dev" within genpd core. The second one is the genpd's
device structure, referenced as genpd->dev. The third one is the virtual
device structures created by the genpd core to represent the consumer
device for multiple power domain case, currently named as genpd_dev. The
naming of these virtual devices isn't very clear or readable and it
looks more like the genpd->dev.
Rename the virtual device instances within the genpd core as "virt_dev".
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
A caller of pm_genpd_init() that provides some states for the genpd via the
->states pointer in the struct generic_pm_domain, should also provide a
governor. This because it's the job of the governor to pick a state that
satisfies the constraints.
Therefore, let's print a warning to inform the user about such bogus
configuration and avoid to bail out, by instead picking the shallowest
state before genpd invokes the ->power_off() callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Instead of returning -EINVAL from of_genpd_parse_idle_states() in case none
compatible states was found, let's return 0 to indicate success. Assign
also the out-parameter *states to NULL and *n to 0, to indicate to the
caller that zero states have been found/allocated.
This enables the caller of of_genpd_parse_idle_states() to easier act on
the returned error code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If __device_suspend() runs asynchronously (in which case the device
passed to it is in dpm_suspended_list at that point) and it returns
early on an error or pending wakeup, and the power.direct_complete
flag has been set for the device already, the subsequent
device_resume() will be confused by that and it will call
pm_runtime_enable() incorrectly, as runtime PM has not been
disabled for the device by __device_suspend().
To avoid that, clear power.direct_complete if __device_suspend()
is not going to disable runtime PM for the device before returning.
Fixes: aae4518b31 (PM / sleep: Mechanism to avoid resuming runtime-suspended devices unnecessarily)
Reported-by: Al Cooper <alcooperx@gmail.com>
Tested-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
"count" needs to be signed for the error handling to work. I made "i"
signed as well so they match.
Fixes: 02113ba93e (PM / clk: Add support for obtaining clocks from device-tree)
Cc: 4.6+ <stable@vger.kernel.org> # 4.6+
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here are all of the driver core and related patches for 4.19-rc1.
Nothing huge here, just a number of small cleanups and the ability to
now stop the deferred probing after init happens.
All of these have been in linux-next for a while with only a merge issue
reported. That merge issue is in fs/sysfs/group.c and Stephen has
posted the diff of what it should be to resolve this. I'll follow up
with that diff to this pull request.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g86Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynyXQCePaZSW8wft4b7nLN8RdZ98ATBru0Ani10lrJa
HQeQJRNbWU1AZ0ym7695
=tOaH
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here are all of the driver core and related patches for 4.19-rc1.
Nothing huge here, just a number of small cleanups and the ability to
now stop the deferred probing after init happens.
All of these have been in linux-next for a while with only a merge
issue reported"
* tag 'driver-core-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (21 commits)
base: core: Remove WARN_ON from link dependencies check
drivers/base: stop new probing during shutdown
drivers: core: Remove glue dirs from sysfs earlier
driver core: remove unnecessary function extern declare
sysfs.h: fix non-kernel-doc comment
PM / Domains: Stop deferring probe at the end of initcall
iommu: Remove IOMMU_OF_DECLARE
iommu: Stop deferring probe at end of initcalls
pinctrl: Support stopping deferred probe after initcalls
dt-bindings: pinctrl: add a 'pinctrl-use-default' property
driver core: allow stopping deferred probe after init
driver core: add a debugfs entry to show deferred devices
sysfs: Fix internal_create_group() for named group updates
base: fix order of OF initialization
linux/device.h: fix kernel-doc notation warning
Documentation: update firmware loader fallback reference
kobject: Replace strncpy with memcpy
drivers: base: cacheinfo: use OF property_read_u32 instead of get_property,read_number
kernfs: Replace strncpy with memcpy
device: Add #define dev_fmt similar to #define pr_fmt
...
All PM domain drivers must be built-in (at least those using DT), so
there is no point deferring probe after initcalls are done. Continuing
to defer probe may prevent booting successfully even if managing PM
domains is not required. This can happen if the user failed to enable
the driver or if power-domains are added to a platform's DT, but there
is not yet a driver (e.g. a new DTB with an old kernel).
Call the driver core function driver_deferred_probe_check_init_done()
instead of just returning -EPROBE_DEFER to stop deferring probe when
initcalls are done.
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <len.brown@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the multiple PM domain case, let's introduce a new API called
dev_pm_domain_attach_by_name(). This allows a consumer driver to associate
its device with one of its PM domains, by using a name based lookup.
Do note that, currently it's only genpd that supports multiple PM domains
per device, but dev_pm_domain_attach_by_name() can easily by extended to
cover other PM domain types, if/when needed.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For the multiple PM domain case, let's introduce a new function called
genpd_dev_pm_attach_by_name(). This allows a device to be associated with
its PM domain through genpd, by using a name based lookup.
Note that, genpd_dev_pm_attach_by_name() shall only be called by the driver
core / PM core, similar to how the existing dev_pm_domain_attach_by_id()
makes use of genpd_dev_pm_attach_by_id(). However, this is implemented by
following changes on top.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are no legacy behavior in drivers to consider while attaching a
device to genpd - for the multiple PM domain case.
For that reason, let's instead require the driver to runtime resume the
device, via calling pm_runtime_get_sync() for example, when it needs to
power on the corresponding PM domain.
This allows us to improve the situation during attach. Instead of always
power on the PM domain, which may be unnecessary, let's leave it in its
current state. Additionally, to avoid the PM domain to stay powered on,
let's schedule a power off work.
Fixes: 3c095f32a9 (PM / Domains: Add support for multi PM domains ...)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The DT node passed here isn't necessarily an OPP node, as this routine
can also be used for cases where the "required-opps" property is present
directly in the device's node. Rename it.
This also removes a stale comment.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Additional updates of the generic power domains (genpd) framework
(support for devices attached to multiple domains) and the cpupower
utility (minor fixes) for 4.18-rc1.
* pm-domains:
PM / Domains: Add dev_pm_domain_attach_by_id() to manage multi PM domains
PM / Domains: Add support for multi PM domains per device to genpd
PM / Domains: Split genpd_dev_pm_attach()
PM / Domains: Don't attach devices in genpd with multi PM domains
PM / Domains: dt: Allow power-domain property to be a list of specifiers
* pm-tools:
cpupower : Fix header name to read idle state name
cpupower: fix spelling mistake: "logilename" -> "logfilename"
Revert commit 1e83786198 (PM / runtime: Fixup reference counting of
device link suppliers at probe), as it has introduced a regression
and the condition it was designed to address should be covered by the
existing code.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently we export event_count instead of wakeup_count via the
per-device wakeup_count sysfs attribute. Change it to wakeup_count
to make it more meaningful.
wakeup_count increments only when events_check_enabled is set,
that is whenever writes the current wakeup count to
/sys/power/wakeup_count. Also events_check_enabled is cleared on
every resume. User space is expected to write to this just before
suspend. This way pm_wakeup_event(), when called from IRQs handles,
will increment wakeup_count only if we are in system-wide
suspend-resume cycle and should give a fair approximation of how many
times a device may have triggered a wakeup from system suspend.
event_count on the other hand will increment every time
pm_wakeup_event() is called irrespective of whether we are in a
suspend-resume cycle and some drivers call it on every interrupt
which makes it less useful for system wakeup tracking.
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The existing dev_pm_domain_attach() function, allows a single PM domain to
be attached per device. To be able to support devices that are partitioned
across multiple PM domains, let's introduce a new interface,
dev_pm_domain_attach_by_id().
The dev_pm_domain_attach_by_id() returns a new allocated struct device with
the corresponding attached PM domain. This enables for example a driver to
operate on the new device from a power management point of view. The driver
may then also benefit from using the received device, to set up so called
device-links towards its original device. Depending on the situation, these
links may then be dynamically changed.
The new interface is typically called by drivers during their probe phase,
in case they manages devices which uses multiple PM domains. If that is the
case, the driver also becomes responsible of managing the detaching of the
PM domains, which typically should be done at the remove phase. Detaching
is done by calling the existing dev_pm_domain_detach() function and for
each of the received devices from dev_pm_domain_attach_by_id().
Note, currently its only genpd that supports multiple PM domains per
device, but dev_pm_domain_attach_by_id() can easily by extended to cover
other PM domain types, if/when needed.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To support devices being partitioned across multiple PM domains, let's
begin with extending genpd to cope with these kind of configurations.
Therefore, add a new exported function genpd_dev_pm_attach_by_id(), which
is similar to the existing genpd_dev_pm_attach(), but with the difference
that it allows its callers to provide an index to the PM domain that it
wants to attach.
Note that, genpd_dev_pm_attach_by_id() shall only be called by the driver
core / PM core, similar to how the existing dev_pm_domain_attach() makes
use of genpd_dev_pm_attach(). However, this is implemented by following
changes on top.
Because, only one PM domain can be attached per device, genpd needs to
create a virtual device that it can attach/detach instead. More precisely,
let the new function genpd_dev_pm_attach_by_id() register a virtual struct
device via calling device_register(). Then let it attach this device to the
corresponding PM domain, rather than the one that is provided by the
caller. The actual attaching is done via re-using the existing genpd OF
functions.
At successful attachment, genpd_dev_pm_attach_by_id() returns the created
virtual device, which allows the caller to operate on it to deal with power
management. Following changes on top, provides more details in this
regards.
To deal with detaching of a PM domain for the multiple PM domains case,
let's also extend the existing genpd_dev_pm_detach() function, to cover the
cleanup of the created virtual device, via make it call device_unregister()
on it. In this way, there is no need to introduce a new function to deal
with detach for the multiple PM domain case, but instead the existing one
is re-used.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To extend genpd to deal with allowing multiple PM domains per device, some
of the code in genpd_dev_pm_attach() can be re-used. Let's prepare for this
by moving some of the code into a sub-function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The power-domain DT property may now contain a list of PM domain
specifiers, which represents that a device are partitioned across multiple
PM domains. This leads to a new situation in genpd_dev_pm_attach(), as only
one PM domain can be attached per device.
To remain things simple for the most common configuration, when a single PM
domain is used, let's treat the multiple PM domain case as being specific.
In other words, let's change genpd_dev_pm_attach() to check for multiple PM
domains and prevent it from attach any PM domain for this case. Instead,
leave this to be managed separately, from following changes to genpd.
Suggested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-pci:
PCI / PM: Clean up outdated comments in pci_target_state()
PCI / PM: Do not clear state_saved for devices that remain suspended
* acpi-pm:
ACPI: EC: Dispatch the EC GPE directly on s2idle wake
ACPICA: Introduce acpi_dispatch_gpe()
* pm-sleep:
PM / hibernate: Fix oops at snapshot_write()
PM / wakeup: Make s2idle_lock a RAW_SPINLOCK
PM / s2idle: Make s2idle_wait_head swait based
PM / wakeup: Make events_lock a RAW_SPINLOCK
PM / suspend: Prevent might sleep splats
* pm-avs:
PM / AVS: rockchip-io: add io selectors and supplies for PX30
* pm-opp: (24 commits)
PM / Domains: Drop unused parameter in genpd_allocate_dev_data()
PM / Domains: Drop genpd as in-param for pm_genpd_remove_device()
PM / Domains: Drop __pm_genpd_add_device()
PM / Domains: Drop extern declarations of functions in pm_domain.h
PM / domains: Add perf_state attribute to genpd debugfs
OPP: Allow same OPP table to be used for multiple genpd
PM / Domain: Return 0 on error from of_genpd_opp_to_performance_state()
PM / OPP: Fix shared OPP table support in dev_pm_opp_register_set_opp_helper()
PM / OPP: Fix shared OPP table support in dev_pm_opp_set_regulators()
PM / OPP: Fix shared OPP table support in dev_pm_opp_set_prop_name()
PM / OPP: Fix shared OPP table support in dev_pm_opp_set_supported_hw()
PM / OPP: silence an uninitialized variable warning
PM / OPP: Remove dev_pm_opp_{un}register_get_pstate_helper()
PM / OPP: Get performance state using genpd helper
PM / Domain: Implement of_genpd_opp_to_performance_state()
PM / Domain: Add support to parse domain's OPP table
PM / Domain: Add struct device to genpd
PM / OPP: Implement dev_pm_opp_get_of_node()
PM / OPP: Implement of_dev_pm_opp_find_required_opp()
PM / OPP: Implement dev_pm_opp_of_add_table_indexed()
...
* pm-domains:
PM / domains: Improve wording of dev_pm_domain_attach() comment
PM / Domains: Don't return -EEXIST at attach when PM domain exists
spi: Respect all error codes from dev_pm_domain_attach()
soundwire: Respect all error codes from dev_pm_domain_attach()
mmc: sdio: Respect all error codes from dev_pm_domain_attach()
i2c: Respect all error codes from dev_pm_domain_attach()
driver core: Respect all error codes from dev_pm_domain_attach()
amba: Respect all error codes from dev_pm_domain_attach()
PM / Domains: Allow a better error handling of dev_pm_domain_attach()
PM / Domains: Check for existing PM domain in dev_pm_domain_attach()
PM / Domains: Drop redundant code in genpd while attaching devices
PM / Domains: Drop comment in genpd about legacy Samsung DT binding
PM / Domains: Fix error path during attach in genpd
The in-parameter struct generic_pm_domain *genpd to
genpd_allocate_dev_data() is unused, so let's drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no need to pass a genpd struct to pm_genpd_remove_device(), as we
already have the information about the PM domain (genpd) through the device
structure.
Additionally, we don't allow to remove a PM domain from a device, other
than the one it may have assigned to it, so really it does not make sense
to have a separate in-param for it.
For these reason, drop it and update the current only call to
pm_genpd_remove_device() from amdgpu_acp.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are still a few non-DT existing users of genpd, however neither of
them uses __pm_genpd_add_device(), hence let's drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that genpd supports performance states, add this additional
attribute as part of the power domains debugfs entry, to display
the current performance state for the Power domain.
Suggested-by: David Collins <collinsd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the case consumer device is runtime resumed, while the link to the
supplier is removed, the earlier call to pm_runtime_get_sync() made from
rpm_get_suppliers() does not get properly balanced with a corresponding
call to pm_runtime_put(). This leads to that suppliers remains to be
runtime resumed forever, while they don't need to.
Let's fix the behaviour by calling rpm_put_suppliers() when dropping a
device link. Not that, since rpm_put_suppliers() checks the
link->rpm_active flag, we can correctly avoid to call pm_runtime_put() in
cases when we shouldn't.
Reported-by: Todor Tomov <todor.tomov@linaro.org>
Fixes: 21d5c57b37 (PM / runtime: Use device links)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the driver core, before it invokes really_probe() it runtime resumes the
suppliers for the device via calling pm_runtime_get_suppliers(), which also
increases the runtime PM usage count for each of the available supplier.
This makes sense, as to be able to allow the consumer device to be probed
by its driver. However, if the driver decides to add a new supplier link
during ->probe(), hence updating the list of suppliers, the following call
to pm_runtime_put_suppliers(), invoked after really_probe() in the driver
core, we get into trouble.
More precisely, pm_runtime_put() gets called also for the new supplier(s),
which is wrong as the driver core, didn't trigger pm_runtime_get_sync() to
be called for it in the first place. In other words, the new supplier may
be runtime suspended even in cases when it shouldn't.
Fix this behaviour, by runtime resume suppliers according to the same
conditions as managed by the runtime PM core, when runtime resume callbacks
are being invoked.
Additionally, don't try to runtime suspend any of the suppliers after
really_probe(), but instead rely on that to happen via the consumer device,
when it becomes runtime suspended.
Fixes: 21d5c57b37 (PM / runtime: Use device links)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The `events_lock' is acquired during suspend while interrupts are
disabled even on RT. The lock is taken only for a very brief moment.
Make it a RAW lock which avoids "sleeping while atomic" warnings on RT.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
of_genpd_opp_to_performance_state() should return 0 on errors, as its
doc comment describes. While it follows that mostly, it returns a
negative error number on one of the failures.
Fix that.
Fixes: 6e41766a6a "PM / Domain: Implement of_genpd_opp_to_performance_state()"
Reported-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The message printed by pm_wakeup_pending() on wakeup detection is
not very useful if someone is not interested specifically in
debugging wakeup, so turn it into a pm_debug() one.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 08810a4119 (PM / core: Add NEVER_SKIP and SMART_PREPARE
driver flags) inadvertently prevented the power.direct_complete flag
from being set for devices without PM callbacks and with disabled
runtime PM which also prevents power.direct_complete from being set
for their parents. That led to problems including a resume crash on
HP ZBook 14u.
Restore the previous behavior by causing power.direct_complete to be
set for those devices again, but do that in a more direct way to
avoid overlooking that case in the future.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199693
Fixes: 08810a4119 (PM / core: Add NEVER_SKIP and SMART_PREPARE driver flags)
Reported-by: Thomas Martitz <kugel@rockbox.org>
Tested-by: Thomas Martitz <kugel@rockbox.org>
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
As dev_pm_domain_attach() isn't the only way to assign PM domain pointers
to devices, clearly we must allow a device to have the pointer already
being assigned. For this reason, return 0 instead of -EEXIST.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The callers of dev_pm_domain_attach() currently checks the returned error
code for -EPROBE_DEFER and needs to ignore other error codes. This is an
unnecessary limitation, which also leads to a rather strange behaviour in
the error path.
Address this limitation, by changing the return codes from
acpi_dev_pm_attach() and genpd_dev_pm_attach(). More precisely, let them
return 0, when no PM domain is needed for the device and then return 1, in
case the device was successfully attached to its PM domain. In this way,
dev_pm_domain_attach(), gets a better understanding of what happens in the
attach attempts and also allowing its caller to better act on real errors
codes.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Instead of checking if an existing PM domain pointer has been assigned in
genpd_dev_pm_attach() and acpi_dev_pm_attach(), move the check to the
common path in dev_pm_domain_attach(), thus potentially avoid one
unnecessary check.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The driver core together with the PM core, nowadays deals with deferring
all probes during the device system sleep phases. Therefore genpd no longer
need to care about this situation, so let's drop the corresponding code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The parsing of the Samsung specific DT binding is gone, but the comment in
the function header remained. Let's drop the comment to avoid confusions.
Fixes: 001d50c9a1 (PM / Domains: Remove obsolete "samsung,power-domain" check)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In case the PM domain fails to be powered on in genpd_dev_pm_attach(), it
returns -EPROBE_DEFER, but keeping the device attached to its PM domain.
This leads to problems when the next attempt to attach is re-tried. More
precisely, in that situation an -EEXIST error code is returned, because the
device already has its PM domain pointer assigned, from the first attempt.
Now, because of the sloppy error handling by the existing callers of
dev_pm_domain_attach(), probing is allowed to continue when -EEXIST is
returned. However, in such case there are no guarantees that the PM domain
is powered on by genpd, which may lead to hangs when buses/drivers tried to
access their devices.
Let's fix this behaviour, simply by detaching the device when powering on
fails in genpd_dev_pm_attach().
Cc: v4.11+ <stable@vger.kernel.org> # v4.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The inline versions of rpm_sysfs_remove() and wakeup_sysfs_add|remove(),
are not being used while CONFIG_PM is unset, hence let's drop them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The functions pm_qos_sysfs_add|remove() are available as inline functions
only while CONFIG_PM is unset, but are not being used. Likely they are a
leftover from an earlier cleanup in the past, anyway let's drop them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The inline versions of dev_pm_arm|disarm_wake_irq() and
dev_pm_enable|disable_wake_irq_check() are not being used while CONFIG_PM
is unset, hence let's drop them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The inline versions of device_wakeup_arm|disarm_wake_irqs(), which are
available while when CONFIG_PM is set and CONFIG_PM_SLEEP unset, are not
being used, hence let's drop them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When wakelock support was added, the wakeup_source_add() function
was updated to set the last_time value of the wakeup source. This
has the unintended side effect of producing confusing output from
pm_print_active_wakeup_sources() when a wakeup source is added
prior to a sleep that is blocked by a different wakeup source.
The function pm_print_active_wakeup_sources() will search for the
most recently active wakeup source when no active source is found.
If a wakeup source is added after a different wakeup source blocks
the system from going to sleep it may have a later last_time value
than the blocking source and be output as the last active wakeup
source even if it has never actually been active.
It looks to me like the change to wakeup_source_add() was made to
prevent the wakelock garbage collection from accidentally dropping
a wakelock during the narrow window between adding the wakelock to
the wakelock list in wakelock_lookup_add() and the activation of
the wakeup source in pm_wake_lock().
This commit changes the behavior so that only the last_time of the
wakeup source used by a wakelock is initialized prior to adding it
to the wakeup source list. This preserves the meaning of the
last_time value as the last time the wakeup source was active and
allows a wakeup source that has never been active to have a
last_time value of 0.
Fixes: b86ff9820f (PM / Sleep: Add user space interface for manipulating wakeup sources, v3)
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
single_open() interface requires that the whole output must
fit into a single buffer. This will lead to timeout when
system memory is not in a good situation.
This patch use seq_open() to show wakeup stats. This method
need only one page, so timeout will not be observed.
Signed-off-by: Ganesh Mahendran <opensource.ganesh@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When we print diagnostic messages about suspend/resume, we have a device
pointer, so use dev_printk() to match other device-related things. Add the
function name, similar to initcall_debug output. E.g.,
- calling 0000:01:00.0+ @ 998, parent: 0000:00:1c.0
+ pci 0000:01:00.0: calling <something> @ 998, parent: 0000:00:1c.0
I wondered if this would break scripts/bootgraph.pl, but I don't think it
will because bootgraph.pl doesn't add any timing information to $start{}
after it sees "Write protecting the" or "Freeing unused kernel memory".
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
initcall_debug_report() always called ktime_get(), even if we didn't
need the result.
Change it so we only call it when we're going to use the result, and
change initcall_debug_start() to follow the same style.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit e8bca479c3 (PM / sleep: trace events for device PM callbacks)
removed the only uses of "state" and "info" from initcall_debug_report().
Remove the now-unused arguments completely.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This implements of_genpd_opp_to_performance_state() which can be used
from the device drivers or the OPP core to find the performance state
encoded in the "required-opps" property of a node. Normally this would
be called only once for each OPP of the device for which the OPP table
of the device is getting generated.
Different platforms may encode the performance state differently using
the OPP table (they may simply return value of opp-hz or opp-microvolt,
or apply some algorithm on top of those values) and so a new callback
->opp_to_performance_state() is implemented to allow platform specific
drivers to convert the power domain OPP to a performance state value.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
The generic power domains can have an OPP table for themselves now, and
phandle of their OPP nodes can be used by the devices powered by the
domain. In order for the OPP core to translate requirements between the
devices and their power domains, both need to have an OPP table in
kernel.
Parse the OPP table for power domains
if they have their
set_performance_state() callback set.
With this patch, an OPP table would be created for the genpd in kernel
based on the OPP table present in DT, if the genpd have its
set_performance_state() callback set.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
The power-domain core would be using the OPP core going forward and the
OPP core has the basic requirement of a device structure for its working.
Add a struct device to the genpd structure. This doesn't register the
device with device core as the "dev" pointer is mostly used by the OPP
core as a cookie for now and registering the device is not mandatory.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
This makes it easy to grep :wakeup /proc/interrupts.
Suggested-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a device is runtime PM suspended when we enter suspend and has
a dedicated wake IRQ, we can get the following warning:
WARNING: CPU: 0 PID: 108 at kernel/irq/manage.c:526 enable_irq+0x40/0x94
[ 102.087860] Unbalanced enable for IRQ 147
...
(enable_irq) from [<c06117a8>] (dev_pm_arm_wake_irq+0x4c/0x60)
(dev_pm_arm_wake_irq) from [<c0618360>]
(device_wakeup_arm_wake_irqs+0x58/0x9c)
(device_wakeup_arm_wake_irqs) from [<c0615948>]
(dpm_suspend_noirq+0x10/0x48)
(dpm_suspend_noirq) from [<c01ac7ac>]
(suspend_devices_and_enter+0x30c/0xf14)
(suspend_devices_and_enter) from [<c01adf20>]
(enter_state+0xad4/0xbd8)
(enter_state) from [<c01ad3ec>] (pm_suspend+0x38/0x98)
(pm_suspend) from [<c01ab3e8>] (state_store+0x68/0xc8)
This is because the dedicated wake IRQ for the device may have been
already enabled earlier by dev_pm_enable_wake_irq_check(). Fix the
issue by checking for runtime PM suspended status.
This issue can be easily reproduced by setting serial console log level
to zero, letting the serial console idle, and suspend the system from
an ssh terminal. On resume, dmesg will have the warning above.
The reason why I have not run into this issue earlier has been that I
typically run my PM test cases from on a serial console instead over ssh.
Fixes: c843455975 (PM / wakeirq: Enable dedicated wakeirq for suspend)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit b539cc82d4 (PM / Domains: Ignore domain-idle-states that are
not compatible), made it possible to ignore non-compatible
domain-idle-states OF nodes. However, in case that happens while doing
the OF parsing, the number of elements in the allocated array would
exceed the numbers actually needed, thus wasting memory.
Fix this by pre-iterating the genpd OF node and counting the number of
compatible domain-idle-states nodes, before doing the allocation. While
doing this, it makes sense to rework the code a bit to avoid open coding,
of parts responsible for the OF node iteration.
Let's also take the opportunity to clarify the function header for
of_genpd_parse_idle_states(), about what is being returned in case of
errors.
Fixes: b539cc82d4 (PM / Domains: Ignore domain-idle-states that are not compatible)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The pm_runtime_force_suspend|resume() helpers currently requires the device
to at some level (PM domain, bus, etc), have the ->runtime_suspend|resume()
callbacks assigned for it, else -ENOSYS is returned as an error.
However, there are no reason for this requirement, so let's simply remove
it by allowing these callbacks to be NULL.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify pm_runtime_need_not_resume() to make it avoid taking
power.child_count for devices with power.ignore_children which
is consistent with the runtime PM usage of these fields.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
One of the limitations of pm_runtime_force_suspend/resume() is that
if a parent driver wants to use these functions, all of its child
drivers generally have to do that too because of the parent usage
counter manipulations necessary to get the correct state of the parent
during system-wide transitions to the working state (system resume).
However, that limitation turns out to be artificial, so remove it.
Namely, pm_runtime_force_suspend() only needs to update the children
counter of its parent (if there's is a parent) when the device can
stay in suspend after the subsequent system resume transition, as
that counter is correct already otherwise. Now, if the parent's
children counter is not updated, it is not necessary to increment
the parent's usage counter in that case any more, as long as the
children counters of devices are checked along with their usage
counters in order to decide whether or not the devices may be left
in suspend after the subsequent system resume transition.
Accordingly, modify pm_runtime_force_suspend() to only call
pm_runtime_set_suspended() for devices whose usage and children
counters are at the "no references" level (the runtime PM status
of the device needs to be updated to "suspended" anyway in case
this function is called once again for the same device during the
transition under way), drop the parent usage counter incrementation
from it and update pm_runtime_force_resume() to compensate for these
changes.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
There are problems with calling pm_runtime_force_suspend/resume()
to "stop" and "start" devices in genpd_finish_suspend() and
genpd_resume_noirq() (and in analogous hibernation-specific genpd
callbacks) after commit 122a22377a (PM / Domains: Stop/start
devices during system PM suspend/resume in genpd) as those routines
do much more than just "stopping" and "starting" devices (which was
the stated purpose of that commit) unnecessarily and may not play
well with system-wide PM driver callbacks.
First, consider the pm_runtime_force_suspend() in
genpd_finish_suspend(). If the current runtime PM status of the
device is "suspended", that function most likely does the right thing
by ignoring the device, because it should have been "stopped" already
and whatever needed to be done to deactivate it shoud have been done.
In turn, if the runtime PM status of the device is "active",
genpd_runtime_suspend() is called for it (indirectly) and (1) runs
the ->runtime_suspend callback provided by the device's driver
(assuming no bus type with ->runtime_suspend of its own), (2) "stops"
the device and (3) checks if the domain can be powered down, and then
(4) the device's runtime PM status is changed to "suspended". Out of
the four actions above (1) is not necessary and it may be outright
harmful, (3) is pointless and (4) is questionable. The only
operation that needs to be carried out here is (2).
The reason why (1) is not necessary is because the system-wide
PM callbacks provided by the device driver for the transition in
question have been run and they should have taken care of the
driver's part of device suspend already. Moreover, it may be
harmful, because the ->runtime_suspend callback may want to
access the device which is partially suspended at that point
and may not be responsive. Also, system-wide PM callbacks may
have been run already (in the previous phases of the system
transition under way) for the device's parent or for its supplier
devices (if any) and the device may not be accessible because of
that.
There also is no reason to do (3), because genpd_finish_suspend()
will repeat it anyway, and (4) potentially causes confusion to ensue
during the subsequent system transition to the working state.
Consider pm_runtime_force_resume() in genpd_resume_noirq() now.
It runs genpd_runtime_resume() for all devices with runtime PM
status set to "suspended", which includes all of the devices
whose runtime PM status was changed by pm_runtime_force_suspend()
before and may include some devices already suspended when the
pm_runtime_force_suspend() was running, which may be confusing. The
genpd_runtime_resume() first tries to power up the domain, which
(again) is pointless, because genpd_resume_noirq() has done that
already. Then, it "starts" the device and runs the ->runtime_resume
callback (from the driver, say) for it. If all is well, the device
is left with the runtime PM status set to "active".
Unfortunately, running the driver's ->runtime_resume callback
before its system-wide PM callbacks and possibly before some
system-wide PM callbacks of the parent device's driver (let
alone supplier drivers) is asking for trouble, especially if
the device had been suspended before pm_runtime_force_suspend()
ran previously or if the callbacks in question expect to be run
back-to-back with their suspend-side counterparts. It also should
not be necessary, because the system-wide PM driver callbacks that
will be invoked for the device subsequently should take care of
resuming it just fine.
[Running the driver's ->runtime_resume callback in the "noirq"
phase of the transition to the working state may be problematic
even for devices whose drivers do use pm_runtime_force_resume()
in (or as) their system-wide PM callbacks if they have suppliers
other than their parents, because it may cause the supplier to
be resumed after the consumer in some cases.]
Because of the above, modify genpd as follows:
1. Change genpd_finish_suspend() to only "stop" devices with
runtime PM status set to "active" (without invoking runtime PM
callbacks for them, changing their runtime PM status and so on).
That doesn't change the handling of devices whose drivers use
pm_runtime_force_suspend/resume() in (or as) their system-wide
PM callbacks and addresses the issues described above for the
other devices.
2. Change genpd_resume_noirq() to only "start" devices with
runtime PM status set to "active" (without invoking runtime PM
callbacks for them, changing their runtime PM status and so on).
Again, that doesn't change the handling of devices whose drivers
use pm_runtime_force_suspend/resume() in (or as) their system-wide
PM callbacks and addresses the described issues for the other
devices. Devices with runtime PM status set to "suspended"
are not started with the assumption that they will be resumed
later, either by pm_runtime_force_resume() or via runtime PM.
3. Change genpd_restore_noirq() to follow genpd_resume_noirq().
That causes devices already suspended before hibernation to be
left alone (which also is the case without the change) and
avoids running the ->runtime_resume driver callback too early
for the other devices.
4. Change genpd_freeze_noirq() and genpd_thaw_noirq() in accordance
with the above modifications.
Fixes: 122a22377a (PM / Domains: Stop/start devices during system PM suspend/resume in genpd)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
In general, wakeup settings are not supposed to be changed during any of
the system wide PM phases. The reason is simply that it would break
guarantees provided by the PM core, to properly act on active wakeup
sources.
However, there are exceptions to when, in particular, disabling a device as
wakeup source makes sense. For example, in cases when a driver realizes
that its device is dead during system suspend. For these scenarios, we
don't need to care about acting on the wakeup source correctly, because a
dead device shouldn't deliver wakeup signals.
To this reasoning and to help users to properly manage wakeup settings,
let's print a warning in cases someone calls device_wakeup_enable() during
system sleep.
Suggested-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[ rjw: Message to be printed ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 10da65423f (PM / Domains: Call driver's noirq callbacks)
started to respect driver's noirq callbacks, but while doing that it
also introduced a few potential problems.
More precisely, in genpd_finish_suspend() and genpd_resume_noirq()
the noirq callbacks at the driver level should be invoked, no matter
of whether dev->power.wakeup_path is set or not.
Additionally, the commit in question also made genpd_resume_noirq()
to ignore the return value from pm_runtime_force_resume().
Let's fix both these issues!
Fixes: 10da65423f (PM / Domains: Call driver's noirq callbacks)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the wakeup_path status flag becomes propagated from a child
device to its parent device at __device_suspend(). This allows a driver
dealing with a parent device to act on the flag from its ->suspend()
callback.
However, in situations when the wakeup_path status flag needs to be set
from a ->suspend_late() callback, its value doesn't get propagated to the
parent by the PM core. Let's address this limitation, by also propagating
the flag at __device_suspend_late().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To make the code more consistent, let's clear the parent's direct_complete
flag along with clearing it for suppliers, instead of as currently, when
propagating the wakeup_path flag to parents.
While changing this, let's take the opportunity to rename the affected
internal functions, to make them self-explanatory. Like this:
dpm_clear_suppliers_direct_complete -> dpm_clear_superiors_direct_complete
dpm_propagate_to_parent -> dpm_propagate_wakeup_to_parent
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PM core in the device_prepare() phase, resets the wakeup_path status
flag to the value of device_may_wakeup(). This means if a ->prepare() or a
->suspend() callback for the device would update the device's wakeup
setting, this doesn't become reflected in the wakeup_path status flag.
In general this isn't a problem, because wakeup settings are not supposed
to be changed (via for example calling device_set_wakeup_enable()) during
any system wide suspend/resume phase. Nevertheless there are some users,
which can be considered as legacy, that don't conform to this behaviour.
These legacy cases should be corrected, however until that is done, let's
address the issue from the PM core, by moving the assignment of the
wakeup_path status flag to the __device_suspend() phase and after the
->suspend() callback has been invoked.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Returning an error code from dev_pm_attach_wake_irq() if
device_wakeup_attach_irq() called by it returns an error is
pointless, because the wakeup source used by it may be deleted
by user space via sysfs at any time and in particular right after
dev_pm_attach_wake_irq() has returned. Moreover, it requires
the callers of dev_pm_attach_wake_irq() to create that wakeup
source via device_wakeup_enable() upfront, but that obviously is
racy with respect to the sysfs-based manipulations of it.
To avoid the race, modify device_wakeup_attach_irq() to check
that the wakeup source it is going to use is there (and return
early otherwise), make it void (as it cannot fail after that
change) and make dev_pm_attach_wake_irq() simply call it for
the device unconditionally.
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make the PM core handle DPM_FLAG_LEAVE_SUSPENDED directly for
devices whose "noirq", "late" and "early" driver callbacks are
invoked directly by it.
Namely, make it skip all of the system-wide resume callbacks for
such devices with DPM_FLAG_LEAVE_SUSPENDED set if they are in
runtime suspend during the "noirq" phase of system-wide suspend
(or analogous) transitions or the system transition under way is
a proper suspend (rather than anything related to hibernation) and
the device's wakeup settings are compatible with runtime PM (that
is, the device cannot generate wakeup signals at all or it is
allowed to wake up the system from sleep).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make the PM core avoid invoking the "late" and "noirq" system-wide
suspend (or analogous) callbacks provided by device drivers directly
for devices with DPM_FLAG_SMART_SUSPEND set that are in runtime
suspend during the "late" and "noirq" phases of system-wide suspend
(or analogous) transitions. That is only done for devices without
any middle-layer "late" and "noirq" suspend callbacks (to avoid
confusing the middle layer if there is one).
The underlying observation is that runtime PM is disabled for devices
during the "late" and "noirq" system-wide suspend phases, so if they
remain in runtime suspend from the "late" phase forward, it doesn't
make sense to invoke the "late" and "noirq" callbacks provided by
the drivers for them (arguably, the device is already suspended and
in the right state). Thus, if the remaining driver suspend callbacks
are to be invoked directly by the core, they can be skipped.
This change really makes it possible for, say, platform device
drivers to re-use runtime PM suspend and resume callbacks by
pointing ->suspend_late and ->resume_early, respectively (and
possibly the analogous hibernation-related callback pointers too),
to them without adding any extra "is the device already suspended?"
type of checks to the callback routines, as long as they will be
invoked directly by the core.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add helper routines to find and return a suitable subsystem callback
during the "noirq" phases of system suspend/resume (or analogous)
transitions as well as during the "late" phase of system suspend and
the "early" phase of system resume (or analogous) transitions.
The helpers will be called from additional sites going forward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Since device_wakeup_disable() checks the device's power.can_wakeup
flag, device_init_wakeup() doesn't need to do that before calling it,
so drop that redundant check from device_init_wakeup().
No intentional changes in functionality.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Since both device_wakeup_enable() and device_wakeup_disable() check
if dev is not NULL and whether or not power.can_wakeup is set for it,
device_set_wakeup_enable() doesn't have to do that, so drop that
check from it.
No intentional changes in functionality.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
I'll admit admit it: I've written bad driver code that tries to
configure a device's wake IRQ without having called device_init_wakeup()
first. But do you really have to ask ask me twice?
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make the PM core call dev_pm_skip_next_resume_phases() to skip the
"early resume" and "resume" phases of system-wide transitions to the
working state for a given device instead of clearing the relevant
status bits for it directly.
No intentional changes in functionality.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
The file was converted from print_fn_descriptor_symbol()
to %pF some time ago (c80cfb0406 "vsprintf: use new
vsprintf symbolic function pointer format"). kallsyms does
not seem to be needed anymore.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the generic PM Domain code code checks for the presence of
both (generic) "power-domains" and (Samsung Exynos legacy)
"samsung,power-domain" properties in all device tree nodes representing
devices.
There are two issues with this:
1. This imposes a small boot-time penalty on all platforms using DT,
2. Platform-specific checks do not really belong in core framework
code.
Remove the platform-specific check, as the last user of
"samsung,power-domain" was removed in commit 46dcf0ff0d ("ARM:
dts: exynos: Remove exynos4415.dtsi"). All other users were converted
before in commit 0da6587041 ("ARM: dts: convert to generic power
domain bindings for exynos DT").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Middle-layer code doing suspend-time optimizations for devices with
the DPM_FLAG_SMART_SUSPEND flag set (currently, the PCI bus type and
the ACPI PM domain) needs to make the core skip ->thaw_early and
->thaw callbacks for those devices in some cases and it sets the
power.direct_complete flag for them for this purpose.
However, it turns out that setting power.direct_complete outside of
the PM core is a bad idea as it triggers an excess invocation of
pm_runtime_enable() in device_resume().
For this reason, provide a helper to clear power.is_late_suspended
and power.is_suspended to be invoked by the middle-layer code in
question instead of setting power.direct_complete and make that code
call the new helper.
Fixes: c4b65157ae (PCI / PM: Take SMART_SUSPEND driver flag into account)
Fixes: 05087360fd (ACPI / PM: Take SMART_SUSPEND driver flag into account)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Let's make the code a bit more readable by moving some of the code, which
deals with adjustments for parent devices in __device_suspend(), into its
own function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use DEVICE_ATTR_RO() and DEVICE_ATTR_RW() macros instead of
open coding them.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no need to use 'else' if in main branch 'return' is present.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
...instead of custom approach.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Prevent rpm_get_suppliers() from returning an error code if runtime
PM is disabled for one or more of the supplier devices it wants to
runtime-resume, so as to make runtime PM work for devices with links
to suppliers that don't use runtime PM (such links may be created
during device enumeration even before it is known whether or not
runtime PM will be enabled for the devices in question, for example).
Fixes: 21d5c57b37 (PM / runtime: Use device links)
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Adrian Hunter <adrian.hunter@intel.com>
Define and document a new driver flag, DPM_FLAG_LEAVE_SUSPENDED, to
instruct the PM core and middle-layer (bus type, PM domain, etc.)
code that it is desirable to leave the device in runtime suspend
after system-wide transitions to the working state (for example,
the device may be slow to resume and it may be better to avoid
resuming it right away).
Generally, the middle-layer code involved in the handling of the
device is expected to indicate to the PM core whether or not the
device may be left in suspend with the help of the device's
power.may_skip_resume status bit. That has to happen in the "noirq"
phase of the preceding system suspend (or analogous) transition.
The middle layer is then responsible for handling the device as
appropriate in its "noirq" resume callback which is executed
regardless of whether or not the device may be left suspended, but
the other resume callbacks (except for ->complete) will be skipped
automatically by the core if the device really can be left in
suspend.
The additional power.must_resume status bit introduced for the
implementation of this mechanisn is used internally by the PM core
to track the requirement to resume the device (which may depend on
its children etc).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
With all callbacks converted, and the timer callback prototype
switched over, the TIMER_FUNC_TYPE cast is no longer needed,
so remove it. Conversion was done with the following scripts:
perl -pi -e 's|\(TIMER_FUNC_TYPE\)||g' \
$(git grep TIMER_FUNC_TYPE | cut -d: -f1 | sort -u)
perl -pi -e 's|\(TIMER_DATA_TYPE\)||g' \
$(git grep TIMER_DATA_TYPE | cut -d: -f1 | sort -u)
The now unused macros are also dropped from include/linux/timer.h.
Signed-off-by: Kees Cook <keescook@chromium.org>
The check for "active" children in __pm_runtime_set_status(), when
trying to set the parent device status to "suspended", doesn't
really make sense, because in fact it is not invalid to set the
status of a device with runtime PM disabled to "suspended" in any
case. It is invalid to enable runtime PM for a device with its
status set to "suspended" while its child_count reference counter
is nonzero, but the check in __pm_runtime_set_status() doesn't
really cover that situation.
For this reason, drop the children check from __pm_runtime_set_status()
and add a check against child_count reference counters of "suspended"
devices to pm_runtime_enable().
Fixes: a8636c8964 (PM / Runtime: Don't allow to suspend a device with an active child)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
- Relocate the OPP (Operating Performance Points) framework to its
own directory under drivers/ and add support for power domain
performance states to it (Viresh Kumar).
- Modify the PM core, the PCI bus type and the ACPI PM domain to
support power management driver flags allowing device drivers to
specify their capabilities and preferences regarding the handling
of devices with enabled runtime PM during system suspend/resume
and clean up that code somewhat (Rafael Wysocki, Ulf Hansson).
- Add frequency-invariant accounting support to the task scheduler
on ARM and ARM64 (Dietmar Eggemann).
- Fix PM QoS device resume latency framework to prevent "no
restriction" requests from overriding requests with specific
requirements and drop the confusing PM_QOS_FLAG_REMOTE_WAKEUP
device PM QoS flag (Rafael Wysocki).
- Drop legacy class suspend/resume operations from the PM core
and drop legacy bus type suspend and resume callbacks from
ARM/locomo (Rafael Wysocki).
- Add min/max frequency support to devfreq and clean it up
somewhat (Chanwoo Choi).
- Rework wakeup support in the generic power domains (genpd)
framework and update some of its users accordingly (Geert
Uytterhoeven).
- Convert timers in the PM core to use timer_setup() (Kees Cook).
- Add support for exposing the SLP_S0 (Low Power S0 Idle)
residency counter based on the LPIT ACPI table on Intel
platforms (Srinivas Pandruvada).
- Add per-CPU PM QoS resume latency support to the ladder cpuidle
governor (Ramesh Thomas).
- Fix a deadlock between the wakeup notify handler and the
notifier removal in the ACPI core (Ville Syrjälä).
- Fix a cpufreq schedutil governor issue causing it to use
stale cached frequency values sometimes (Viresh Kumar).
- Fix an issue in the system suspend core support code causing
wakeup events detection to fail in some cases (Rajat Jain).
- Fix the generic power domains (genpd) framework to prevent
the PM core from using the direct-complete optimization with
it as that is guaranteed to fail (Ulf Hansson).
- Fix a minor issue in the cpuidle core and clean it up a bit
(Gaurav Jindal, Nicholas Piggin).
- Fix and clean up the intel_idle and ARM cpuidle drivers (Jason
Baron, Len Brown, Leo Yan).
- Fix a couple of minor issues in the OPP framework and clean it
up (Arvind Yadav, Fabio Estevam, Sudeep Holla, Tobias Jordan).
- Fix and clean up some cpufreq drivers and fix a minor issue in
the cpufreq statistics code (Arvind Yadav, Bhumika Goyal, Fabio
Estevam, Gautham Shenoy, Gustavo Silva, Marek Szyprowski, Masahiro
Yamada, Robert Jarzmik, Zumeng Chen).
- Fix minor issues in the system suspend and hibernation core, in
power management documentation and in the AVS (Adaptive Voltage
Scaling) framework (Helge Deller, Himanshu Jha, Joe Perches,
Rafael Wysocki).
- Fix some issues in the cpupower utility and document that Shuah
Khan is going to maintain it going forward (Prarit Bhargava,
Shuah Khan).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=QTnx
-----END PGP SIGNATURE-----
Merge tag 'pm-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"There are no real big ticket items here this time.
The most noticeable change is probably the relocation of the OPP
(Operating Performance Points) framework to its own directory under
drivers/ as it has grown big enough for that. Also Viresh is now going
to maintain it and send pull requests for it to me, so you will see
this change in the git history going forward (but still not right
now).
Another noticeable set of changes is the modifications of the PM core,
the PCI subsystem and the ACPI PM domain to allow of more integration
between system-wide suspend/resume and runtime PM. For now it's just a
way to avoid resuming devices from runtime suspend unnecessarily
during system suspend (if the driver sets a flag to indicate its
readiness for that) and in the works is an analogous mechanism to
allow devices to stay suspended after system resume.
In addition to that, we have some changes related to supporting
frequency-invariant CPU utilization metrics in the scheduler and in
the schedutil cpufreq governor on ARM and changes to add support for
device performance states to the generic power domains (genpd)
framework.
The rest is mostly fixes and cleanups of various sorts.
Specifics:
- Relocate the OPP (Operating Performance Points) framework to its
own directory under drivers/ and add support for power domain
performance states to it (Viresh Kumar).
- Modify the PM core, the PCI bus type and the ACPI PM domain to
support power management driver flags allowing device drivers to
specify their capabilities and preferences regarding the handling
of devices with enabled runtime PM during system suspend/resume and
clean up that code somewhat (Rafael Wysocki, Ulf Hansson).
- Add frequency-invariant accounting support to the task scheduler on
ARM and ARM64 (Dietmar Eggemann).
- Fix PM QoS device resume latency framework to prevent "no
restriction" requests from overriding requests with specific
requirements and drop the confusing PM_QOS_FLAG_REMOTE_WAKEUP
device PM QoS flag (Rafael Wysocki).
- Drop legacy class suspend/resume operations from the PM core and
drop legacy bus type suspend and resume callbacks from ARM/locomo
(Rafael Wysocki).
- Add min/max frequency support to devfreq and clean it up somewhat
(Chanwoo Choi).
- Rework wakeup support in the generic power domains (genpd)
framework and update some of its users accordingly (Geert
Uytterhoeven).
- Convert timers in the PM core to use timer_setup() (Kees Cook).
- Add support for exposing the SLP_S0 (Low Power S0 Idle) residency
counter based on the LPIT ACPI table on Intel platforms (Srinivas
Pandruvada).
- Add per-CPU PM QoS resume latency support to the ladder cpuidle
governor (Ramesh Thomas).
- Fix a deadlock between the wakeup notify handler and the notifier
removal in the ACPI core (Ville Syrjälä).
- Fix a cpufreq schedutil governor issue causing it to use stale
cached frequency values sometimes (Viresh Kumar).
- Fix an issue in the system suspend core support code causing wakeup
events detection to fail in some cases (Rajat Jain).
- Fix the generic power domains (genpd) framework to prevent the PM
core from using the direct-complete optimization with it as that is
guaranteed to fail (Ulf Hansson).
- Fix a minor issue in the cpuidle core and clean it up a bit (Gaurav
Jindal, Nicholas Piggin).
- Fix and clean up the intel_idle and ARM cpuidle drivers (Jason
Baron, Len Brown, Leo Yan).
- Fix a couple of minor issues in the OPP framework and clean it up
(Arvind Yadav, Fabio Estevam, Sudeep Holla, Tobias Jordan).
- Fix and clean up some cpufreq drivers and fix a minor issue in the
cpufreq statistics code (Arvind Yadav, Bhumika Goyal, Fabio
Estevam, Gautham Shenoy, Gustavo Silva, Marek Szyprowski, Masahiro
Yamada, Robert Jarzmik, Zumeng Chen).
- Fix minor issues in the system suspend and hibernation core, in
power management documentation and in the AVS (Adaptive Voltage
Scaling) framework (Helge Deller, Himanshu Jha, Joe Perches, Rafael
Wysocki).
- Fix some issues in the cpupower utility and document that Shuah
Khan is going to maintain it going forward (Prarit Bhargava, Shuah
Khan)"
* tag 'pm-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (88 commits)
tools/power/cpupower: add libcpupower.so.0.0.1 to .gitignore
tools/power/cpupower: Add 64 bit library detection
intel_idle: Graceful probe failure when MWAIT is disabled
cpufreq: schedutil: Reset cached_raw_freq when not in sync with next_freq
freezer: Fix typo in freezable_schedule_timeout() comment
PM / s2idle: Clear the events_check_enabled flag
cpufreq: stats: Handle the case when trans_table goes beyond PAGE_SIZE
cpufreq: arm_big_little: make cpufreq_arm_bL_ops structures const
cpufreq: arm_big_little: make function arguments and structure pointer const
cpuidle: Avoid assignment in if () argument
cpuidle: Clean up cpuidle_enable_device() error handling a bit
ACPI / PM: Fix acpi_pm_notifier_lock vs flush_workqueue() deadlock
PM / Domains: Fix genpd to deal with drivers returning 1 from ->prepare()
cpuidle: ladder: Add per CPU PM QoS resume latency support
PM / QoS: Fix device resume latency framework
PM / domains: Rework governor code to be more consistent
PM / Domains: Remove gpd_dev_ops.active_wakeup() callback
soc: rockchip: power-domain: Use GENPD_FLAG_ACTIVE_WAKEUP
soc: mediatek: Use GENPD_FLAG_ACTIVE_WAKEUP
ARM: shmobile: pm-rmobile: Use GENPD_FLAG_ACTIVE_WAKEUP
...
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
* pm-core:
ACPI / PM: Take SMART_SUSPEND driver flag into account
PCI / PM: Take SMART_SUSPEND driver flag into account
PCI / PM: Drop unnecessary invocations of pcibios_pm_ops callbacks
PM / core: Add SMART_SUSPEND driver flag
PCI / PM: Use the NEVER_SKIP driver flag
PM / core: Add NEVER_SKIP and SMART_PREPARE driver flags
PM / core: Convert timers to use timer_setup()
PM / core: Fix kerneldoc comments of four functions
PM / core: Drop legacy class suspend/resume operations
* pm-sleep:
freezer: Fix typo in freezable_schedule_timeout() comment
PM / s2idle: Clear the events_check_enabled flag
PM / sleep: Remove pm_complete_with_resume_check()
PM: ARM: locomo: Drop suspend and resume bus type callbacks
PM: Use a more common logging style
PM: Document rules on using pm_runtime_resume() in system suspend callbacks
* pm-cpufreq-sched:
cpufreq: schedutil: Reset cached_raw_freq when not in sync with next_freq
* pm-opp:
PM / OPP: Add dev_pm_opp_{un}register_get_pstate_helper()
PM / OPP: Support updating performance state of device's power domain
PM / OPP: add missing of_node_put() for of_get_cpu_node()
PM / OPP: Rename dev_pm_opp_register_put_opp_helper()
PM / OPP: Add missing of_node_put(np)
PM / OPP: Move error message to debug level
PM / OPP: Use snprintf() to avoid kasprintf() and kfree()
PM / OPP: Move the OPP directory out of power/
* pm-domains:
PM / Domains: Fix genpd to deal with drivers returning 1 from ->prepare()
PM / domains: Rework governor code to be more consistent
PM / Domains: Remove gpd_dev_ops.active_wakeup() callback
soc: rockchip: power-domain: Use GENPD_FLAG_ACTIVE_WAKEUP
soc: mediatek: Use GENPD_FLAG_ACTIVE_WAKEUP
ARM: shmobile: pm-rmobile: Use GENPD_FLAG_ACTIVE_WAKEUP
PM / Domains: Allow genpd users to specify default active wakeup behavior
PM / Domains: Add support to select performance-state of domains
PM / Domains: Rename genpd internals from pm_genpd_* to genpd_*
During system-wide PM, genpd relies on its PM callbacks to be invoked for
all its attached devices, as to deal with powering off/on the PM domain. In
other words, genpd is not compatible with the direct_complete path, if
executed by the PM core for any of its attached devices.
However, when genpd's ->prepare() callback invokes pm_generic_prepare(), it
does not take into account that it may return 1. Instead it treats that as
an error internally and expects the PM core to abort the prepare phase and
roll back. This leads to genpd not properly powering on/off the PM domain,
because its internal counters gets wrongly balanced.
To fix the behaviour, allow drivers to return 1 from their ->prepare()
callbacks, but let's return 0 from genpd's ->prepare() callback in such
case, as that prevents the PM core from running the direct_complete path
for the device.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The special value of 0 for device resume latency PM QoS means
"no restriction", but there are two problems with that.
First, device resume latency PM QoS requests with 0 as the
value are always put in front of requests with positive
values in the priority lists used internally by the PM QoS
framework, causing 0 to be chosen as an effective constraint
value. However, that 0 is then interpreted as "no restriction"
effectively overriding the other requests with specific
restrictions which is incorrect.
Second, the users of device resume latency PM QoS have no
way to specify that *any* resume latency at all should be
avoided, which is an artificial limitation in general.
To address these issues, modify device resume latency PM QoS to
use S32_MAX as the "no constraint" value and 0 as the "no
latency at all" one and rework its users (the cpuidle menu
governor, the genpd QoS governor and the runtime PM framework)
to follow these changes.
Also add a special "n/a" value to the corresponding user space I/F
to allow user space to indicate that it cannot accept any resume
latencies at all for the given device.
Fixes: 85dc0b8a40 (PM / QoS: Make it possible to expose PM QoS latency constraints)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197323
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Ramesh Thomas <ramesh.thomas@intel.com>
The genpd governor currently uses negative PM QoS values to indicate
the "no suspend" condition and 0 as "no restriction", but it doesn't
use them consistently. Moreover, it tries to refresh QoS values for
already suspended devices in a quite questionable way.
For the above reasons, rework it to be a bit more consistent.
First off, note that dev_pm_qos_read_value() in
dev_update_qos_constraint() and __default_power_down_ok() is
evaluated for devices in suspend. Moreover, that only happens if the
effective_constraint_ns value for them is negative (meaning "no
suspend"). It is not evaluated in any other cases, so effectively
the QoS values are only updated for devices in suspend that should
not have been suspended in the first place. In all of the other
cases, the QoS values taken into account are the effective ones from
the time before the device has been suspended, so generally devices
need to be resumed and suspended again for new QoS values to take
effect anyway. Thus evaluating dev_update_qos_constraint() in
those two places doesn't make sense at all, so drop it.
Second, initialize effective_constraint_ns to 0 ("no constraint")
rather than to (-1) ("no suspend"), which makes more sense in
general and in case effective_constraint_ns is never updated
(the device is in suspend all the time or it is never suspended)
it doesn't affect the device's parent and so on.
Finally, rework default_suspend_ok() to explicitly handle the
"no restriction" and "no suspend" special cases.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Ramesh Thomas <ramesh.thomas@intel.com>
There are no more users left of the gpd_dev_ops.active_wakeup()
callback. All have been converted to GENPD_FLAG_ACTIVE_WAKEUP.
Hence remove the callback.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is quite common for PM Domains to require slave devices to be kept
active during system suspend if they are to be used as wakeup sources.
To enable this, currently each PM Domain or driver has to provide its
own gpd_dev_ops.active_wakeup() callback.
Introduce a new flag GENPD_FLAG_ACTIVE_WAKEUP to consolidate this.
If specified, all slave devices configured as wakeup sources will be
kept active during system suspend.
PM Domains that need more fine-grained controls, based on the slave
device, can still provide their own callbacks, as before.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make the PCI bus type take DPM_FLAG_SMART_SUSPEND into account in its
system-wide PM callbacks and make sure that all code that should not
run in parallel with pci_pm_runtime_resume() is executed in the "late"
phases of system suspend, freeze and poweroff transitions.
[Note that the pm_runtime_suspended() check in pci_dev_keep_suspended()
is an optimization, because if is not passed, all of the subsequent
checks may be skipped and some of them are much more overhead in
general.]
Also use the observation that if the device is in runtime suspend
at the beginning of the "late" phase of a system-wide suspend-like
transition, its state cannot change going forward (runtime PM is
disabled for it at that time) until the transition is over and the
subsequent system-wide PM callbacks should be skipped for it (as
they generally assume the device to not be suspended), so add checks
for that in pci_pm_suspend_late/noirq(), pci_pm_freeze_late/noirq()
and pci_pm_poweroff_late/noirq().
Moreover, if pci_pm_resume_noirq() or pci_pm_restore_noirq() is
called during the subsequent system-wide resume transition and if
the device was left in runtime suspend previously, its runtime PM
status needs to be changed to "active" as it is going to be put
into the full-power state, so add checks for that too to these
functions.
In turn, if pci_pm_thaw_noirq() runs after the device has been
left in runtime suspend, the subsequent "thaw" callbacks need
to be skipped for it (as they may not work correctly with a
suspended device), so set the power.direct_complete flag for the
device then to make the PM core skip those callbacks.
In addition to the above add a core helper for checking if
DPM_FLAG_SMART_SUSPEND is set and the device runtime PM status is
"suspended" at the same time, which is done quite often in the new
code (and will be done elsewhere going forward too).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Define and document a SMART_SUSPEND flag to instruct bus types and PM
domains that the system suspend callbacks provided by the driver can
cope with runtime-suspended devices, so from the driver's perspective
it should be safe to leave devices in runtime suspend during system
suspend.
Setting that flag may also cause middle-layer code (bus types,
PM domains etc.) to skip invocations of the ->suspend_late and
->suspend_noirq callbacks provided by the driver if the device
is in runtime suspend at the beginning of the "late" phase of
the system-wide suspend transition, in which case the driver's
system-wide resume callbacks may be invoked back-to-back with
its ->runtime_suspend callback, so the driver has to be able to
cope with that too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
The motivation for this change is to provide a way to work around
a problem with the direct-complete mechanism used for avoiding
system suspend/resume handling for devices in runtime suspend.
The problem is that some middle layer code (the PCI bus type and
the ACPI PM domain in particular) returns positive values from its
system suspend ->prepare callbacks regardless of whether the driver's
->prepare returns a positive value or 0, which effectively prevents
drivers from being able to control the direct-complete feature.
Some drivers need that control, however, and the PCI bus type has
grown its own flag to deal with this issue, but since it is not
limited to PCI, it is better to address it by adding driver flags at
the core level.
To that end, add a driver_flags field to struct dev_pm_info for flags
that can be set by device drivers at the probe time to inform the PM
core and/or bus types, PM domains and so on on the capabilities and/or
preferences of device drivers. Also add two static inline helpers
for setting that field and testing it against a given set of flags
and make the driver core clear it automatically on driver remove
and probe failures.
Define and document two PM driver flags related to the direct-
complete feature: NEVER_SKIP and SMART_PREPARE that can be used,
respectively, to indicate to the PM core that the direct-complete
mechanism should never be used for the device and to inform the
middle layer code (bus types, PM domains etc) that it can only
request the PM core to use the direct-complete mechanism for
the device (by returning a positive value from its ->prepare
callback) if it also has been requested by the driver.
While at it, make the core check pm_runtime_suspended() when
setting power.direct_complete so that it doesn't need to be
checked by ->prepare callbacks.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The special value of 0 for device resume latency PM QoS means
"no restriction", but there are two problems with that.
First, device resume latency PM QoS requests with 0 as the
value are always put in front of requests with positive
values in the priority lists used internally by the PM QoS
framework, causing 0 to be chosen as an effective constraint
value. However, that 0 is then interpreted as "no restriction"
effectively overriding the other requests with specific
restrictions which is incorrect.
Second, the users of device resume latency PM QoS have no
way to specify that *any* resume latency at all should be
avoided, which is an artificial limitation in general.
To address these issues, modify device resume latency PM QoS to
use S32_MAX as the "no constraint" value and 0 as the "no
latency at all" one and rework its users (the cpuidle menu
governor, the genpd QoS governor and the runtime PM framework)
to follow these changes.
Also add a special "n/a" value to the corresponding user space I/F
to allow user space to indicate that it cannot accept any resume
latencies at all for the given device.
Fixes: 85dc0b8a40 (PM / QoS: Make it possible to expose PM QoS latency constraints)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197323
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alex Shi <alex.shi@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Removes test of .data field, since
that will be going away.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix the kerneldoc comments of __device_suspend_noirq(),
__device_suspend_late() and __device_suspend() where the function
names in kerneldoc don't match the actual names of the functions.
Also fix the device_resume_noirq() kerneldoc comment which mentions
"early resume" instead of "noirq resume" incorrectly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
The PM QoS flag PM_QOS_FLAG_REMOTE_WAKEUP is not used consistently
and the vast majority of code simply assumes that remote wakeup
should be enabled for devices in runtime suspend if they can
generate wakeup signals, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Some platforms have the capability to configure the performance state of
PM domains. This patch enhances the genpd core to support such
platforms.
The performance levels (within the genpd core) are identified by
positive integer values, a lower value represents lower performance
state.
This patch adds a new genpd API, which is called by user drivers (like
OPP framework):
- int dev_pm_genpd_set_performance_state(struct device *dev,
unsigned int state);
This updates the performance state constraint of the device on its PM
domain. On success, the genpd will have its performance state set to a
value which is >= "state" passed to this routine. The genpd core calls
the genpd->set_performance_state() callback, if implemented,
else -ENODEV is returned to the caller.
The PM domain drivers need to implement the following callback if they
want to support performance states.
- int (*set_performance_state)(struct generic_pm_domain *genpd,
unsigned int state);
This is called internally by the genpd core on several occasions. The
genpd core passes the genpd pointer and the aggregate of the
performance states of the devices supported by that genpd to this
callback. This callback must update the performance state of the genpd
(in a platform dependent way).
The power domains can avoid supplying above callback, if they don't
support setting performance-states.
Currently we aren't propagating performance state changes of a subdomain
to its masters as we don't have hardware that needs it right now. Over
that, the performance states of subdomain and its masters may not have
one-to-one mapping and would require additional information. We can get
back to this once we have hardware that needs it.
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
According to recent changes for ACPI, the are longer any users of
pm_complete_with_resume_check(), thus let's drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the functions names has already moved the genpd naming rules,
however let's make this complete to avoid any further confusions.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove uses of init_timer_on_stack() with open-coded function and data
assignments that could be expressed using timer_setup_on_stack(). Several
were removed from the stack entirely since there was a one-to-one mapping
of parent structure to timer, those are switched to using timer_setup()
instead. All related callbacks were adjusted to use from_timer().
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Petr Mladek <pmladek@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux1394-devel@lists.sourceforge.net
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: linux-s390@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: linux-scsi@vger.kernel.org
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Ursula Braun <ubraun@linux.vnet.ibm.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Harish Patil <harish.patil@cavium.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Reed <mdr@sgi.com>
Cc: Manish Chopra <manish.chopra@cavium.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-pm@vger.kernel.org
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Mark Gross <mark.gross@intel.com>
Cc: linux-watchdog@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: netdev@vger.kernel.org
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lkml.kernel.org/r/1507159627-127660-4-git-send-email-keescook@chromium.org
The drivers/base/power/ directory is special and contains code related
to power management core like system suspend/resume, hibernation, etc.
It was fine to keep the OPP code inside it when we had just one file for
it, but it is growing now and already has a directory for itself.
Lets move it directly under drivers/ directory, just like cpufreq and
cpuidle.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The notifier callbacks may want to call some OPP helper routines which
may try to take the same opp_table->lock again and cause a deadlock. One
such usecase was reported by Chanwoo Choi, where calling
dev_pm_opp_disable() leads us to the devfreq's OPP notifier handler,
which further calls dev_pm_opp_find_freq_floor() and it deadlocks.
We don't really need the opp_table->lock to be held across the notifier
call though, all we want to make sure is that the 'opp' doesn't get
freed while being used from within the notifier chain. We can do it with
help of dev_pm_opp_get/put() as well. Let's do it.
Cc: 4.11+ <stable@vger.kernel.org> # 4.11+
Fixes: 5b650b3888 "PM / OPP: Take kref from _find_opp_table()"
Reported-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are no classes using the legacy suspend/resume operations in
the tree any more, so drop these operations and update the code
referring to them accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* pm-core:
PM: core: Fix device_pm_check_callbacks()
* pm-qos:
PM / QoS: Use the correct variable to check the QoS request type
* pm-docs:
PM: docs: Drop an excess character from devices.rst
driver core: Fix link to device power management documentation
