The messages should be different depending on the type of error.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
include/asm-generic/pci-bridge.h is now empty, so remove every #include of
it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com> (arm64)
* pci/host-vmd:
x86/PCI: Add driver for Intel Volume Management Device (VMD)
PCI/AER: Use 32 bit PCI domain numbers
x86/PCI: Allow DMA ops specific to a PCI domain
irqdomain: Export irq_domain_set_info() for module use
genirq/MSI: Relax msi_domain_alloc() to support parentless MSI irqdomains
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
The Intel Volume Management Device (VMD) is a PCIe endpoint that acts as a
host bridge to another PCI domain. When devices below the VMD perform DMA,
the VMD replaces their DMA source IDs with its own source ID. Therefore,
those devices require special DMA ops.
Add interfaces to allow the VMD driver to set up dma_ops for the devices
below it.
[bhelgaas: remove "extern", add "static", changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There is some repetitive code in the switch/case statements in
pci_bios_read() and pci_bios_write(). Factor out the BIOS function
IDs and the result widths to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Commit 4d6b4e69a2 ("x86/PCI/ACPI: Use common interface to support
PCI host bridge") converted x86 to use the common interface
acpi_pci_root_create, but the conversion missed on code piece in
arch/x86/pci/bus_numa.c, which causes regression on some legacy
AMD platforms as reported by Arthur Marsh <arthur.marsh@internode.on.net>.
The root causes is that acpi_pci_root_create() fails to insert
host bridge resources into iomem_resource/ioport_resource because
x86_pci_root_bus_resources() has already inserted those resources.
So change x86_pci_root_bus_resources() to not insert resources into
iomem_resource/ioport_resource.
Fixes: 4d6b4e69a2 ("x86/PCI/ACPI: Use common interface to support PCI host bridge")
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Reported-and-tested-by: Arthur Marsh <arthur.marsh@internode.on.net>
Reported-and-tested-by: Krzysztof Kolasa <kkolasa@winsoft.pl>
Reported-and-tested-by: Keith Busch <keith.busch@intel.com>
Reported-and-tested-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pci/aer:
PCI/AER: Clear error status registers during enumeration and restore
* pci/hotplug:
PCI: pciehp: Queue power work requests in dedicated function
* pci/misc:
PCI: Turn off Request Attributes to avoid Chelsio T5 Completion erratum
x86/PCI: Make pci_subsys_init() static
PCI: Add builtin_pci_driver() to avoid registration boilerplate
PCI: Remove unnecessary "if" statement
* pci/msi:
x86/PCI: Don't alloc pcibios-irq when MSI is enabled
PCI/MSI: Export all remapped MSIs to sysfs attributes
PCI: Disable MSI on SiS 761
* pci/resource:
sparc/PCI: Add mem64 resource parsing for root bus
PCI: Expand Enhanced Allocation BAR output
PCI: Make Enhanced Allocation bitmasks more obvious
PCI: Handle Enhanced Allocation capability for SR-IOV devices
PCI: Add support for Enhanced Allocation devices
PCI: Add Enhanced Allocation register entries
PCI: Handle IORESOURCE_PCI_FIXED when assigning resources
PCI: Handle IORESOURCE_PCI_FIXED when sizing resources
PCI: Clear IORESOURCE_UNSET when reverting to firmware-assigned address
* pci/virtualization:
PCI: Fix sriov_enable() error path for pcibios_enable_sriov() failures
PCI: Wait 1 second between disabling VFs and clearing NumVFs
PCI: Reorder pcibios_sriov_disable()
PCI: Remove VFs in reverse order if virtfn_add() fails
PCI: Remove redundant validation of SR-IOV offset/stride registers
PCI: Set SR-IOV NumVFs to zero after enumeration
PCI: Enable SR-IOV ARI Capable Hierarchy before reading TotalVFs
PCI: Don't try to restore VF BARs
The pcibios-irq and MSI both use dev->irq to store the IRQ number. While
the MSI code checks for that and frees the pcibios-irq before overwriting
dev->irq, the pcibios_alloc_irq() function does not.
Usually this is not a problem, as the pcibios-irq is allocated before probe
time of the device and the MSI IRQ is allocted from the driver's probe
path.
But there are PCI devices handled by the core kernel and not by a standard
PCI driver, like the AMD IOMMU for example. For the AMD IOMMU a normal PCI
device driver does not make sense, because a driver can be forcibly unbound
from its device, which is not a good idea for an IOMMU.
Nevertheless the PCI core code tries to match the PCI device implementing
the AMD IOMMU against drivers, and allocates/frees a pcibios IRQ every time
it tries out a new driver. This overwrites the dev->irq field set by
pci_enable_msi() and sets it to 0 in the end (because the probe fails and
the pcibios-irq is freed again).
On suspend/resume this breaks the kernel, because the IRQ descriptor for
IRQ 0 is NULL.
Fix this by not allocating a pcibios-irq when MSI is already active. This
also has the benefit, that a device claimed by the core kernel can not be
probed by a PCI driver later.
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Use common interface to simplify ACPI PCI host bridge implementation.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reset acpi_root_dev->domain to 0 when pci_ignore_seg is set to keep
consistence between ACPI PCI root device and PCI host bridge device.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The pci_subsys_init() is a subsys_initcall that can be declared static.
Signed-off-by: Alexander Kuleshov <kuleshovmail@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Revert dff22d2054 ("PCI: Call pci_read_bridge_bases() from core instead
of arch code").
Reading PCI bridge windows is not arch-specific in itself, but there is PCI
core code that doesn't work correctly if we read them too early. For
example, Hannes found this case on an ARM Freescale i.mx6 board:
pci_bus 0000:00: root bus resource [mem 0x01000000-0x01efffff]
pci 0000:00:00.0: PCI bridge to [bus 01-ff]
pci 0000:00:00.0: BAR 8: no space for [mem size 0x01000000] (mem window)
pci 0000:01:00.0: BAR 2: failed to assign [mem size 0x00200000]
pci 0000:01:00.0: BAR 1: failed to assign [mem size 0x00004000]
pci 0000:01:00.0: BAR 0: failed to assign [mem size 0x00000100]
The 00:00.0 mem window needs to be at least 3MB: the 01:00.0 device needs
0x204100 of space, and mem windows are megabyte-aligned.
Bus sizing can increase a bridge window size, but never *decrease* it (see
d65245c329 ("PCI: don't shrink bridge resources")). Prior to
dff22d2054, ARM didn't read bridge windows at all, so the "original size"
was zero, and we assigned a 3MB window.
After dff22d2054, we read the bridge windows before sizing the bus. The
firmware programmed a 16MB window (size 0x01000000) in 00:00.0, and since
we never decrease the size, we kept 16MB even though we only needed 3MB.
But 16MB doesn't fit in the host bridge aperture, so we failed to assign
space for the window and the downstream devices.
I think this is a defect in the PCI core: we shouldn't rely on the firmware
to assign sensible windows.
Ray reported a similar problem, also on ARM, with Broadcom iProc.
Issues like this are too hard to fix right now, so revert dff22d2054.
Reported-by: Hannes <oe5hpm@gmail.com>
Reported-by: Ray Jui <rjui@broadcom.com>
Link: http://lkml.kernel.org/r/CAAa04yFQEUJm7Jj1qMT57-LG7ZGtnhNDBe=PpSRa70Mj+XhW-A@mail.gmail.com
Link: http://lkml.kernel.org/r/55F75BB8.4070405@broadcom.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Pull irq updates from Thomas Gleixner:
"This updated pull request does not contain the last few GIC related
patches which were reported to cause a regression. There is a fix
available, but I let it breed for a couple of days first.
The irq departement provides:
- new infrastructure to support non PCI based MSI interrupts
- a couple of new irq chip drivers
- the usual pile of fixlets and updates to irq chip drivers
- preparatory changes for removal of the irq argument from interrupt
flow handlers
- preparatory changes to remove IRQF_VALID"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources
irqchip: Add bcm2836 interrupt controller for Raspberry Pi 2
irqchip: Add documentation for the bcm2836 interrupt controller
irqchip/bcm2835: Add support for being used as a second level controller
irqchip/bcm2835: Refactor handle_IRQ() calls out of MAKE_HWIRQ
PCI: xilinx: Fix typo in function name
irqchip/gic: Ensure gic_cpu_if_up/down() programs correct GIC instance
irqchip/gic: Only allow the primary GIC to set the CPU map
PCI/MSI: pci-xgene-msi: Consolidate chained IRQ handler install/remove
unicore32/irq: Prepare puv3_gpio_handler for irq argument removal
tile/pci_gx: Prepare trio_handle_level_irq for irq argument removal
m68k/irq: Prepare irq handlers for irq argument removal
C6X/megamode-pic: Prepare megamod_irq_cascade for irq argument removal
blackfin: Prepare irq handlers for irq argument removal
arc/irq: Prepare idu_cascade_isr for irq argument removal
sparc/irq: Use access helper irq_data_get_affinity_mask()
sparc/irq: Use helper irq_data_get_irq_handler_data()
parisc/irq: Use access helper irq_data_get_affinity_mask()
mn10300/irq: Use access helper irq_data_get_affinity_mask()
irqchip/i8259: Prepare i8259_irq_dispatch for irq argument removal
...
Pull x86 core platform updates from Ingo Molnar:
"The main changes are:
- Intel Atom platform updates. (Andy Shevchenko)
- modularity fixlets. (Paul Gortmaker)
- x86 platform clockevents driver updates for lguest, uv and Xen.
(Viresh Kumar)
- Microsoft Hyper-V TSC fixlet. (Vitaly Kuznetsov)"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/platform: Make atom/pmc_atom.c explicitly non-modular
x86/hyperv: Mark the Hyper-V TSC as unstable
x86/xen/time: Migrate to new set-state interface
x86/uv/time: Migrate to new set-state interface
x86/lguest/timer: Migrate to new set-state interface
x86/pci/intel_mid_pci: Use proper constants for irq polarity
x86/pci/intel_mid_pci: Make intel_mid_pci_ops static
x86/pci/intel_mid_pci: Propagate actual return code
x86/pci/intel_mid_pci: Work around for IRQ0 assignment
x86/platform/iosf_mbi: Add Intel Tangier PCI id
x86/platform/iosf_mbi: Source cleanup
x86/platform/iosf_mbi: Remove NULL pointer checks for pci_dev_put()
x86/platform/iosf_mbi: Check return value of debugfs_create properly
x86/platform/iosf_mbi: Move to dedicated folder
x86/platform/intel/pmc_atom: Move the PMC-Atom code to arch/x86/platform/atom
x86/platform/intel/pmc_atom: Add Cherrytrail PMC interface
x86/platform/intel/pmc_atom: Supply register mappings via PMC object
x86/platform/intel/pmc_atom: Print index of device in loop
x86/platform/intel/pmc_atom: Export accessors to PMC registers
* pci/irq:
PCI/MSI: Free legacy IRQ when enabling MSI/MSI-X
PCI: Add helpers to manage pci_dev->irq and pci_dev->irq_managed
PCI, x86: Implement pcibios_alloc_irq() and pcibios_free_irq()
PCI: Add pcibios_alloc_irq() and pcibios_free_irq()
* pci/misc:
PCI: Remove unused "pci_probe" flags
PCI: Add VPD function 0 quirk for Intel Ethernet devices
PCI: Add dev_flags bit to access VPD through function 0
PCI / ACPI: Fix pci_acpi_optimize_delay() comment
PCI: Remove a broken link in quirks.c
PCI: Remove useless redundant code
PCI: Simplify pci_find_(ext_)capability() return value checks
PCI: Move PCI_FIND_CAP_TTL to pci.h and use it in quirks
PCI: Add pcie_downstream_port() (true for Root and Switch Downstream Ports)
PCI: Fix pcie_port_device_resume() comment
PCI: Shift PCI_CLASS_NOT_DEFINED consistently with other classes
PCI: Revert aeb30016fe ("PCI: add Intel USB specific reset method")
PCI: Fix TI816X class code quirk
PCI: Fix generic NCR 53c810 class code quirk
PCI: Use PCI_CLASS_SERIAL_USB instead of bare number
PCI: Add quirk for Intersil/Techwell TW686[4589] AV capture cards
PCI: Remove Intel Cherrytrail D3 delays
* pci/resource:
PCI: Call pci_read_bridge_bases() from core instead of arch code
* pci/virtualization:
PCI: Restore ACS configuration as part of pci_restore_state()
Add pci_has_managed_irq(), pci_set_managed_irq(), and
pci_reset_managed_irq() to simplify code. No functional change.
[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
To support IOAPIC hotplug, we need to allocate PCI IRQ resources on demand
and free them when not used anymore.
Implement pcibios_alloc_irq() and pcibios_free_irq() to dynamically
allocate and free PCI IRQs.
Remove mp_should_keep_irq(), which is no longer used.
[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
polarity = 0 means active high. Not really intuitive, so people add
comments to it instead of just using a self explaining constant.
Use the IOAPIC_POL_ constants and get rid of those horrible to read
tail comments.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
This fixes the following sparse warning.
arch/x86/pci/intel_mid_pci.c:265:16: warning: symbol 'intel_mid_pci_ops' was not declared. Should it be static?
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: http://lkml.kernel.org/r/1438161409-4671-4-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
mp_map_gsi_to_irq() returns different codes if it fails.
intel_mid_pci_irq_enable() hides this under -EBUSY.
Return the actual failure code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: http://lkml.kernel.org/r/1438161409-4671-3-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On Intel Tangier the MMC host controller is wired up to irq 0. But
several other devices have irq 0 associated as well due to a bogus PCI
configuration.
The first initialized driver will acquire irq 0 and make it
unavailable for other devices. If the sdhci driver is not the first
one it will fail to acquire the interrupt and therefor be non
functional.
Add a quirk to the pci irq enable function which denies irq 0 to
anything else than the MMC host controller driver on Tangier
platforms.
Fixes: 90b9aacf91 (serial: 8250_pci: add Intel Tangier support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: http://lkml.kernel.org/r/1438161409-4671-2-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When we scan a PCI bus, we read PCI-PCI bridge window registers with
pci_read_bridge_bases() so we can validate the resource hierarchy. Most
architectures call pci_read_bridge_bases() from pcibios_fixup_bus(), but
PCI-PCI bridges are not arch-specific, so this doesn't need to be in
arch-specific code.
Call pci_read_bridge_bases() directly from the PCI core instead of from
arch code.
For alpha and mips, we now call pci_read_bridge_bases() always; previously
we only called it if PCI_PROBE_ONLY was set.
[bhelgaas: changelog]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: James E.J. Bottomley <jejb@parisc-linux.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: David Howells <dhowells@redhat.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Tony Luck <tony.luck@intel.com>
CC: David S. Miller <davem@davemloft.net>
CC: Ingo Molnar <mingo@redhat.com>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Michal Simek <monstr@monstr.eu>
CC: Chris Zankel <chris@zankel.net>
Use accessor for_each_pci_msi_entry() to access MSI device list, so we
could easily move msi_list from struct pci_dev into struct device
later.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: xen-devel@lists.xenproject.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Stuart Yoder <stuart.yoder@freescale.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1436428847-8886-6-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In the generic quirk fixup_rev1_53c810(), added by a5312e28c1 ("[PATCH]
PCI: NCR 53c810 quirk"), we assigned "class = PCI_CLASS_STORAGE_SCSI". But
PCI_CLASS_STORAGE_SCSI is only the two-byte base class/sub-class and needs
to be shifted to make space for the low-order interface byte.
Furthermore, we had a similar quirk, pci_fixup_ncr53c810(), for arch/x86,
which assigned class correctly. The arch code is linked before the PCI
core, so arch quirks run before generic quirks. Therefore, on x86, the x86
arch quirk ran first, and the generic quirk did nothing because it saw that
dev->class was already set. But on other arches, the generic quirk set the
wrong class code.
Fix the generic quirk to set the correct class code and remove the
now-unnecessary x86-specific quirk.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Matthew Wilcox <matthew@wil.cx>
We enable _CRS on all systems from 2008 and later. On older systems, we
ignore _CRS and assume the whole physical address space (excluding RAM and
other devices) is available for PCI devices, but on systems that support
physical address spaces larger than 4GB, it's doubtful that the area above
4GB is really available for PCI.
After d56dbf5bab ("PCI: Allocate 64-bit BARs above 4G when possible"), we
try to use that space above 4GB *first*, so we're more likely to put a
device there.
On Juan's Toshiba Satellite Pro U200, BIOS left the graphics, sound, 1394,
and card reader devices unassigned (but only after Windows had been
booted). Only the sound device had a 64-bit BAR, so it was the only device
placed above 4GB, and hence the only device that didn't work.
Keep _CRS enabled even on pre-2008 systems if they support physical address
space larger than 4GB.
Fixes: d56dbf5bab ("PCI: Allocate 64-bit BARs above 4G when possible")
Reported-and-tested-by: Juan Dayer <jdayer@outlook.com>
Reported-and-tested-by: Alan Horsfield <alan@hazelgarth.co.uk>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=99221
Link: https://bugzilla.opensuse.org/show_bug.cgi?id=907092
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.14+
The Foxconn K8M890-8237A has two PCI host bridges, and we can't assign
resources correctly without the information from _CRS that tells us which
address ranges are claimed by which bridge. In the bugs mentioned below,
we incorrectly assign a sound card address (this example is from 1033299):
bus: 00 index 2 [mem 0x80000000-0xfcffffffff]
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7f])
pci_root PNP0A08:00: host bridge window [mem 0x80000000-0xbfefffff] (ignored)
pci_root PNP0A08:00: host bridge window [mem 0xc0000000-0xdfffffff] (ignored)
pci_root PNP0A08:00: host bridge window [mem 0xf0000000-0xfebfffff] (ignored)
ACPI: PCI Root Bridge [PCI1] (domain 0000 [bus 80-ff])
pci_root PNP0A08:01: host bridge window [mem 0xbff00000-0xbfffffff] (ignored)
pci 0000:80:01.0: [1106:3288] type 0 class 0x000403
pci 0000:80:01.0: reg 10: [mem 0xbfffc000-0xbfffffff 64bit]
pci 0000:80:01.0: address space collision: [mem 0xbfffc000-0xbfffffff 64bit] conflicts with PCI Bus #00 [mem 0x80000000-0xfcffffffff]
pci 0000:80:01.0: BAR 0: assigned [mem 0xfd00000000-0xfd00003fff 64bit]
BUG: unable to handle kernel paging request at ffffc90000378000
IP: [<ffffffffa0345f63>] azx_create+0x37c/0x822 [snd_hda_intel]
We assigned 0xfd_0000_0000, but that is not in any of the host bridge
windows, and the sound card doesn't work.
Turn on pci=use_crs automatically for this system.
Link: https://bugs.launchpad.net/ubuntu/+source/alsa-driver/+bug/931368
Link: https://bugs.launchpad.net/ubuntu/+source/alsa-driver/+bug/1033299
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
Commit 97badf873a (device property: Make it possible to use
secondary firmware nodes) uncovered a bug in the x86 (and ia64) PCI
host bridge initialization code that assumes bridge->bus->sysdata
to always point to a struct pci_sysdata object which need not be
the case (in particular, the Xen PCI frontend driver sets it to point
to a different data type). If it is not the case, an incorrect
pointer (or a piece of data that is not a pointer at all) will be
passed to ACPI_COMPANION_SET() and that may cause interesting
breakage to happen going forward.
To work around this problem use the observation that the ACPI
host bridge initialization always passes NULL as parent to
pci_create_root_bus(), so if pcibios_root_bridge_prepare() sees
a non-NULL parent of the bridge, it should not attempt to set
an ACPI companion for it, because that means that
pci_create_root_bus() has been called by someone else.
Fixes: 97badf873a (device property: Make it possible to use secondary firmware nodes)
Reported-and-tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
We use pat_enabled in x86-specific code to see if PAT is enabled
or not but we're granting full access to it even though readers
do not need to set it. If, for instance, we granted access to it
to modules later they then could override the variable
setting... no bueno.
This renames pat_enabled to a new static variable __pat_enabled.
Folks are redirected to use pat_enabled() now.
Code that sets this can only be internal to pat.c. Apart from
the early kernel parameter "nopat" to disable PAT, we also have
a few cases that disable it later and make use of a helper
pat_disable(). It is wrapped under an ifdef but since that code
cannot run unless PAT was enabled its not required to wrap it
with ifdefs, unwrap that. Likewise, since "nopat" doesn't really
change non-PAT systems just remove that ifdef as well.
Although we could add and use an early_param_off(), these
helpers don't use __read_mostly but we want to keep
__read_mostly for __pat_enabled as this is a hot path -- upon
boot, for instance, a simple guest may see ~4k accesses to
pat_enabled(). Since __read_mostly early boot params are not
that common we don't add a helper for them just yet.
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kyle McMartin <kyle@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1430425520-22275-3-git-send-email-mcgrof@do-not-panic.com
Link: http://lkml.kernel.org/r/1432628901-18044-13-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This routine has been around for over a decade, but with EISA
being dead and abandoned for about twice that long, the name can
be kind of confusing. The function is going at the PIC Edge/Level
Configuration Registers (ELCR), so rename it as such and mentally
decouple it from the long since dead EISA bus.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Maciej W. Rozycki <macro@linux-mips.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Len Brown <len.brown@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/1431217657-934-1-git-send-email-paul.gortmaker@windriver.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
An IO port or MMIO resource assigned to a PCI host bridge may be
consumed by the host bridge itself or available to its child
bus/devices. The ACPI specification defines a bit (Producer/Consumer)
to tell whether the resource is consumed by the host bridge itself,
but firmware hasn't used that bit consistently, so we can't rely on it.
Before commit 593669c2ac ("x86/PCI/ACPI: Use common ACPI resource
interfaces to simplify implementation"), arch/x86/pci/acpi.c ignored
all IO port resources defined by acpi_resource_io and
acpi_resource_fixed_io to filter out IO ports consumed by the host
bridge itself.
Commit 593669c2ac ("x86/PCI/ACPI: Use common ACPI resource interfaces
to simplify implementation") started accepting all IO port and MMIO
resources, which caused a regression that IO port resources consumed
by the host bridge itself became available to its child devices.
Then commit 63f1789ec7 ("x86/PCI/ACPI: Ignore resources consumed by
host bridge itself") ignored resources consumed by the host bridge
itself by checking the IORESOURCE_WINDOW flag, which accidently removed
MMIO resources defined by acpi_resource_memory24, acpi_resource_memory32
and acpi_resource_fixed_memory32.
On x86 and IA64 platforms, all IO port and MMIO resources are assumed
to be available to child bus/devices except one special case:
IO port [0xCF8-0xCFF] is consumed by the host bridge itself
to access PCI configuration space.
So explicitly filter out PCI CFG IO ports[0xCF8-0xCFF]. This solution
will also ease the way to consolidate ACPI PCI host bridge common code
from x86, ia64 and ARM64.
Related ACPI table are archived at:
https://bugzilla.kernel.org/show_bug.cgi?id=94221
Related discussions at:
http://patchwork.ozlabs.org/patch/461633/https://lkml.org/lkml/2015/3/29/304
Fixes: 63f1789ec7 (Ignore resources consumed by host bridge itself)
Reported-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: 4.0+ <stable@vger.kernel.org> # 4.0+
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Convert IOAPIC driver to support and use hierarchical irqdomain
interfaces. It's a little big, but would break bisecting if we split
it into multiple patches.
Fold in a patch from Andy Shevchenko <andriy.shevchenko@linux.intel.com>
to make it bisectable.
http://lkml.org/lkml/2014/12/10/622
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Joerg Roedel <jroedel@suse.de>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: sfi-devel@simplefirmware.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Link: http://lkml.kernel.org/r/1428905519-23704-38-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Introduce helper functions to manipulate struct irq_alloc_info for
IOAPIC. Also add an extra parameter to IOAPIC interfaces to prepare
for hierarchical irqdomain. Function mp_set_gsi_attr() will be removed
once we have switched to hierarchical irqdomains.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Joerg Roedel <jroedel@suse.de>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Link: http://lkml.kernel.org/r/1428905519-23704-33-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit b4b55cda58 (Refine the way to release PCI IRQ resources)
introduced a regression in the PCI IRQ resource management by causing
the IRQ resource of a device, established when pci_enabled_device()
is called on a fully disabled device, to be released when the driver
is unbound from the device, regardless of the enable_cnt.
This leads to the situation that an ill-behaved driver can now make a
device unusable to subsequent drivers by an imbalance in their use of
pci_enable/disable_device(). That is a serious problem for secondary
drivers like vfio-pci, which are innocent of the transgressions of
the previous driver.
Since the solution of this problem is not immediate and requires
further discussion, revert commit b4b55cda58 and the issue it was
supposed to address (a bug related to xen-pciback) will be taken
care of in a different way going forward.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Previously, pci_scan_root_bus() created a root PCI bus, enumerated the
devices on it, and called pci_bus_add_devices(), which made the devices
available for drivers to claim them.
Most callers assigned resources to devices after pci_scan_root_bus()
returns, which may be after drivers have claimed the devices. This is
incorrect; the PCI core should not change device resources while a driver
is managing the device.
Remove pci_bus_add_devices() from pci_scan_root_bus() and do it after any
resource assignment in the callers.
Note that ARM's pci_common_init_dev() already called pci_bus_add_devices()
after pci_scan_root_bus(), so we only need to remove the first call:
pci_common_init_dev
pcibios_init_hw
pci_scan_root_bus
pci_bus_add_devices # first call
pci_bus_assign_resources
pci_bus_add_devices # second call
[bhelgaas: changelog, drop "root_bus" var in alpha common_init_pci(),
return failure earlier in mn10300, add "return" in x86 pcibios_scan_root(),
return early if xtensa platform_pcibios_fixup() fails]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
CC: Matt Turner <mattst88@gmail.com>
CC: David Howells <dhowells@redhat.com>
CC: Tony Luck <tony.luck@intel.com>
CC: Michal Simek <monstr@monstr.eu>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
CC: Sebastian Ott <sebott@linux.vnet.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Chris Metcalf <cmetcalf@ezchip.com>
CC: Chris Zankel <chris@zankel.net>
CC: Max Filippov <jcmvbkbc@gmail.com>
CC: Thomas Gleixner <tglx@linutronix.de>
When parsing resources for PCI host bridge, we should ignore resources
consumed by host bridge itself and only report window resources available
to child PCI busses.
Fixes: 593669c2ac (x86/PCI/ACPI: Use common ACPI resource interfaces ...)
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Rework of the core ACPI resources parsing code to fix issues
in it and make using resource offsets more convenient and
consolidation of some resource-handing code in a couple of places
that have grown analagous data structures and code to cover the
the same gap in the core (Jiang Liu, Thomas Gleixner, Lv Zheng).
- ACPI-based IOAPIC hotplug support on top of the resources handling
rework (Jiang Liu, Yinghai Lu).
- ACPICA update to upstream release 20150204 including an interrupt
handling rework that allows drivers to install raw handlers for
ACPI GPEs which then become entirely responsible for the given GPE
and the ACPICA core code won't touch it (Lv Zheng, David E Box,
Octavian Purdila).
- ACPI EC driver rework to fix several concurrency issues and other
problems related to events handling on top of the ACPICA's new
support for raw GPE handlers (Lv Zheng).
- New ACPI driver for AMD SoCs analogous to the LPSS (Low-Power
Subsystem) driver for Intel chips (Ken Xue).
- Two minor fixes of the ACPI LPSS driver (Heikki Krogerus,
Jarkko Nikula).
- Two new blacklist entries for machines (Samsung 730U3E/740U3E and
510R) where the native backlight interface doesn't work correctly
while the ACPI one does (Hans de Goede).
- Rework of the ACPI processor driver's handling of idle states
to make the code more straightforward and less bloated overall
(Rafael J Wysocki).
- Assorted minor fixes related to ACPI and SFI (Andreas Ruprecht,
Andy Shevchenko, Hanjun Guo, Jan Beulich, Rafael J Wysocki,
Yaowei Bai).
- PCI core power management modification to avoid resuming (some)
runtime-suspended devices during system suspend if they are in
the right states already (Rafael J Wysocki).
- New SFI-based cpufreq driver for Intel platforms using SFI
(Srinidhi Kasagar).
- cpufreq core fixes, cleanups and simplifications (Viresh Kumar,
Doug Anderson, Wolfram Sang).
- SkyLake CPU support and other updates for the intel_pstate driver
(Kristen Carlson Accardi, Srinivas Pandruvada).
- cpufreq-dt driver cleanup (Markus Elfring).
- Init fix for the ARM big.LITTLE cpuidle driver (Sudeep Holla).
- Generic power domains core code fixes and cleanups (Ulf Hansson).
- Operating Performance Points (OPP) core code cleanups and kernel
documentation update (Nishanth Menon).
- New dabugfs interface to make the list of PM QoS constraints
available to user space (Nishanth Menon).
- New devfreq driver for Tegra Activity Monitor (Tomeu Vizoso).
- New devfreq class (devfreq_event) to provide raw utilization data
to devfreq governors (Chanwoo Choi).
- Assorted minor fixes and cleanups related to power management
(Andreas Ruprecht, Krzysztof Kozlowski, Rickard Strandqvist,
Pavel Machek, Todd E Brandt, Wonhong Kwon).
- turbostat updates (Len Brown) and cpupower Makefile improvement
(Sriram Raghunathan).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=zZER
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"We have a few new features this time, including a new SFI-based
cpufreq driver, a new devfreq driver for Tegra Activity Monitor, a new
devfreq class for providing its governors with raw utilization data
and a new ACPI driver for AMD SoCs.
Still, the majority of changes here are reworks of existing code to
make it more straightforward or to prepare it for implementing new
features on top of it. The primary example is the rework of ACPI
resources handling from Jiang Liu, Thomas Gleixner and Lv Zheng with
support for IOAPIC hotplug implemented on top of it, but there is
quite a number of changes of this kind in the cpufreq core, ACPICA,
ACPI EC driver, ACPI processor driver and the generic power domains
core code too.
The most active developer is Viresh Kumar with his cpufreq changes.
Specifics:
- Rework of the core ACPI resources parsing code to fix issues in it
and make using resource offsets more convenient and consolidation
of some resource-handing code in a couple of places that have grown
analagous data structures and code to cover the the same gap in the
core (Jiang Liu, Thomas Gleixner, Lv Zheng).
- ACPI-based IOAPIC hotplug support on top of the resources handling
rework (Jiang Liu, Yinghai Lu).
- ACPICA update to upstream release 20150204 including an interrupt
handling rework that allows drivers to install raw handlers for
ACPI GPEs which then become entirely responsible for the given GPE
and the ACPICA core code won't touch it (Lv Zheng, David E Box,
Octavian Purdila).
- ACPI EC driver rework to fix several concurrency issues and other
problems related to events handling on top of the ACPICA's new
support for raw GPE handlers (Lv Zheng).
- New ACPI driver for AMD SoCs analogous to the LPSS (Low-Power
Subsystem) driver for Intel chips (Ken Xue).
- Two minor fixes of the ACPI LPSS driver (Heikki Krogerus, Jarkko
Nikula).
- Two new blacklist entries for machines (Samsung 730U3E/740U3E and
510R) where the native backlight interface doesn't work correctly
while the ACPI one does (Hans de Goede).
- Rework of the ACPI processor driver's handling of idle states to
make the code more straightforward and less bloated overall (Rafael
J Wysocki).
- Assorted minor fixes related to ACPI and SFI (Andreas Ruprecht,
Andy Shevchenko, Hanjun Guo, Jan Beulich, Rafael J Wysocki, Yaowei
Bai).
- PCI core power management modification to avoid resuming (some)
runtime-suspended devices during system suspend if they are in the
right states already (Rafael J Wysocki).
- New SFI-based cpufreq driver for Intel platforms using SFI
(Srinidhi Kasagar).
- cpufreq core fixes, cleanups and simplifications (Viresh Kumar,
Doug Anderson, Wolfram Sang).
- SkyLake CPU support and other updates for the intel_pstate driver
(Kristen Carlson Accardi, Srinivas Pandruvada).
- cpufreq-dt driver cleanup (Markus Elfring).
- Init fix for the ARM big.LITTLE cpuidle driver (Sudeep Holla).
- Generic power domains core code fixes and cleanups (Ulf Hansson).
- Operating Performance Points (OPP) core code cleanups and kernel
documentation update (Nishanth Menon).
- New dabugfs interface to make the list of PM QoS constraints
available to user space (Nishanth Menon).
- New devfreq driver for Tegra Activity Monitor (Tomeu Vizoso).
- New devfreq class (devfreq_event) to provide raw utilization data
to devfreq governors (Chanwoo Choi).
- Assorted minor fixes and cleanups related to power management
(Andreas Ruprecht, Krzysztof Kozlowski, Rickard Strandqvist, Pavel
Machek, Todd E Brandt, Wonhong Kwon).
- turbostat updates (Len Brown) and cpupower Makefile improvement
(Sriram Raghunathan)"
* tag 'pm+acpi-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (151 commits)
tools/power turbostat: relax dependency on APERF_MSR
tools/power turbostat: relax dependency on invariant TSC
Merge branch 'pci/host-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci into acpi-resources
tools/power turbostat: decode MSR_*_PERF_LIMIT_REASONS
tools/power turbostat: relax dependency on root permission
ACPI / video: Add disable_native_backlight quirk for Samsung 510R
ACPI / PM: Remove unneeded nested #ifdef
USB / PM: Remove unneeded #ifdef and associated dead code
intel_pstate: provide option to only use intel_pstate with HWP
ACPI / EC: Add GPE reference counting debugging messages
ACPI / EC: Add query flushing support
ACPI / EC: Refine command storm prevention support
ACPI / EC: Add command flushing support.
ACPI / EC: Introduce STARTED/STOPPED flags to replace BLOCKED flag
ACPI: add AMD ACPI2Platform device support for x86 system
ACPI / table: remove duplicate NULL check for the handler of acpi_table_parse()
ACPI / EC: Update revision due to raw handler mode.
ACPI / EC: Reduce ec_poll() by referencing the last register access timestamp.
ACPI / EC: Fix several GPE handling issues by deploying ACPI_GPE_DISPATCH_RAW_HANDLER mode.
ACPICA: Events: Enable APIs to allow interrupt/polling adaptive request based GPE handling model
...
* acpi-resources: (23 commits)
Merge branch 'pci/host-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci into acpi-resources
x86/irq, ACPI: Implement ACPI driver to support IOAPIC hotplug
ACPI: Add interfaces to parse IOAPIC ID for IOAPIC hotplug
x86/PCI: Refine the way to release PCI IRQ resources
x86/PCI/ACPI: Use common ACPI resource interfaces to simplify implementation
x86/PCI: Fix the range check for IO resources
PCI: Use common resource list management code instead of private implementation
resources: Move struct resource_list_entry from ACPI into resource core
ACPI: Introduce helper function acpi_dev_filter_resource_type()
ACPI: Add field offset to struct resource_list_entry
ACPI: Translate resource into master side address for bridge window resources
ACPI: Return translation offset when parsing ACPI address space resources
ACPI: Enforce stricter checks for address space descriptors
ACPI: Set flag IORESOURCE_UNSET for unassigned resources
ACPI: Normalize return value of resource parser functions
ACPI: Fix a bug in parsing ACPI Memory24 resource
ACPI: Add prefetch decoding to the address space parser
ACPI: Move the window flag logic to the combined parser
ACPI: Unify the parsing of address_space and ext_address_space
ACPI: Let the parser return false for disabled resources
...
* acpica:
ACPICA: Events: Enable APIs to allow interrupt/polling adaptive request based GPE handling model
ACPICA: Events: Introduce acpi_set_gpe()/acpi_finish_gpe() to reduce divergences
ACPICA: Events: Introduce ACPI_GPE_DISPATCH_RAW_HANDLER to fix 2 issues for the current GPE APIs
ACPICA: Update version to 20150204
ACPICA: Update Copyright headers to 2015
ACPICA: Hardware: Cast GPE enable_mask before storing
ACPICA: Events: Cleanup GPE dispatcher type obtaining code
ACPICA: Events: Cleanup to move acpi_gbl_global_event_handler invocation out of acpi_ev_gpe_dispatch()
ACPICA: Events: Cleanup of resetting the GPE handler to NULL before removing
ACPICA: Events: Fix uninitialized variable
ACPICA: Events: Remove acpi_ev_valid_gpe_event() due to current restriction
ACPICA: Events: Remove duplicated sanity check in acpi_ev_enable_gpe()
ACPICA: Events: Back port "ACPICA: Save current masks of enabled GPEs after enable register writes"
ACPICA: Resources: Provide common part for struct acpi_resource_address structures.
ACPI: Introduce acpi_unload_parent_table() usages in Linux kernel
ACPICA: take ACPI_MTX_INTERPRETER in acpi_unload_table_id()
The major highlight this release is a refactoring of the core to allow
us to run synchronous transfers in the context of the caller when there
is no contention for the bus. This improves performance in the very
common case by eliminating context switches and reducing the number of
hardware setup and teardown operations we need to perform.
Other changes:
- New drivers for DLN-2 USB-SPI adapter and ST SPI controllers.
- A big round of cleanups, performance and feature improvements
for the xilinx driver from Ricardo Ribalda Delgado.
- A wide range of smaller cleanups, fixes and feature improvements
throughout the subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU2GNgAAoJECTWi3JdVIfQLiYH/0uLN43CunPp0gSWllQ2PY1O
R1QiqXg1fr1uZKRuGy59QF0TkU/JlWPY+tpGiOH1jrnDsoecnWsxDx3YEeuYdV6U
c//UrlK2uvESivbc48zVUTwCsgxsE8apG0JgqLjsfUpqZTEFxFpeSskepSJ2kIUz
bsXHU8Xi0WkLalsk/8Ik8aUvOwVi5EtRE9OMvnU6QPqQMCszgv1TH4UbwbhqwwzZ
U23WbNHQ262XDRwY2LKl/QROULeU5pd9F19wrveKMa42fkbu/e+kk6E3n7/Hd4mV
CUjv1wTCpPZvzh3bTk50uXwA9XQOzv6ddw6jqsgLcV6jS8Ju3Z3Beya3fmdhOl0=
=3ZQr
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The major highlight this release is a refactoring of the core to allow
us to run synchronous transfers in the context of the caller when
there is no contention for the bus. This improves performance in the
very common case by eliminating context switches and reducing the
number of hardware setup and teardown operations we need to perform.
Other changes:
- New drivers for DLN-2 USB-SPI adapter and ST SPI controllers.
- A big round of cleanups, performance and feature improvements for
the xilinx driver from Ricardo Ribalda Delgado.
- A wide range of smaller cleanups, fixes and feature improvements
throughout the subsystem"
* tag 'spi-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (68 commits)
spi: mxs: cleanup wait_for_completion return handling
spi: ti-qspi: cleanup wait_for_completion return handling
spi: spi-imx: cleanup wait_for_completion handling
spi: sh-msiof: cleanup wait_for_completion return handling
spi: match var type to return type of wait_for_completion
spi: spi-pxa2xx: only include mach/dma.h for legacy DMA
spi: atmel: cleanup wait_for_completion return handling
spi: fsl-dspi: Remove possible memory leak of 'chip'
spi: sh-msiof: Update calculation of frequency dividing
spi: spidev: Convert buf pointers for 32-bit compat SPI_IOC_MESSAGE(n)
spi/xilinx: Fix access invalid memory on xilinx_spi_tx
spi: Revert "spi/xilinx: Remove iowrite/ioread wrappers"
spi/xilinx: Check number of slaves range
spi/xilinx: Use polling mode on small transfers
spi/xilinx: Remove remaining_words driver data variable
spi/xilinx: Remove iowrite/ioread wrappers
spi/xilinx: Convert bits_per_word in bytes_per_word
spi/xilinx: Convert remainding_bytes in remaining words
spi/xilinx: Make spi_tx and spi_rx simmetric
spi/xilinx: Remove rx_fn and tx_fn pointer
...
Some PCI device drivers assume that pci_dev->irq won't change after
calling pci_disable_device() and pci_enable_device() during suspend and
resume.
Commit c03b3b0738 ("x86, irq, mpparse: Release IOAPIC pin when
PCI device is disabled") frees PCI IRQ resources when pci_disable_device()
is called and reallocate IRQ resources when pci_enable_device() is
called again. This breaks above assumption. So commit 3eec595235
("x86, irq, PCI: Keep IRQ assignment for PCI devices during
suspend/hibernation") and 9eabc99a63 ("x86, irq, PCI: Keep IRQ
assignment for runtime power management") fix the issue by avoiding
freeing/reallocating IRQ resources during PCI device suspend/resume.
They achieve this by checking dev.power.is_prepared and
dev.power.runtime_status. PM maintainer, Rafael, then pointed out that
it's really an ugly fix which leaking PM internal state information to
IRQ subsystem.
Recently David Vrabel <david.vrabel@citrix.com> also reports an
regression in pciback driver caused by commit cffe0a2b5a ("x86, irq:
Keep balance of IOAPIC pin reference count"). Please refer to:
http://lkml.org/lkml/2015/1/14/546
So this patch refine the way to release PCI IRQ resources. Instead of
releasing PCI IRQ resources in pci_disable_device()/
pcibios_disable_device(), we now release it at driver unbinding
notification BUS_NOTIFY_UNBOUND_DRIVER. In other word, we only release
PCI IRQ resources when there's no driver bound to the PCI device, and
it keeps the assumption that pci_dev->irq won't through multiple
invocation of pci_enable_device()/pci_disable_device().
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use common ACPI resource discovery interfaces to simplify PCI host bridge
resource enumeration.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The range check in setup_res() checks the IO range against
iomem_resource. That's just wrong.
Reworked based on Thomas original patch.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use common resource list management data structure and interfaces
instead of private implementation.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
NEC OEMs the same platforms as Stratus does, which have multiple devices on
some PCIe buses under downstream ports.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=51331
Fixes: 1278998f8f ("PCI: Work around Stratus ftServer broken PCIe hierarchy (fix DMI check)")
Signed-off-by: Charlotte Richardson <charlotte.richardson@stratus.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.5+
CC: Myron Stowe <myron.stowe@redhat.com>
Unlike MSI, which is configured via registers in the MSI capability in
Configuration Space, MSI-X is configured via tables in Memory Space.
These MSI-X tables are mapped by a device BAR, and if no Memory Space
has been assigned to the BAR, MSI-X cannot be used.
Fail MSI-X setup if no space has been assigned for the BAR.
Previously, we ioremapped the MSI-X table even if the resource hadn't been
assigned. In this case, the resource address is undefined (and is often
zero), which may lead to warnings or oopses in this path:
pci_enable_msix
msix_capability_init
msix_map_region
ioremap_nocache
The PCI core sets resource flags to zero when it can't assign space for the
resource (see reset_resource()). There are also some cases where it sets
the IORESOURCE_UNSET flag, e.g., pci_reassigndev_resource_alignment(),
pci_assign_resource(), etc. So we must check for both cases.
[bhelgaas: changelog]
Reported-by: Zhang Jukuo <zhangjukuo@huawei.com>
Tested-by: Zhang Jukuo <zhangjukuo@huawei.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
struct acpi_resource_address and struct acpi_resource_extended_address64 share substracts
just at different offsets. To unify the parsing functions, OSPMs like Linux
need a new ACPI_ADDRESS64_ATTRIBUTE as their substructs, so they can
extract the shared data.
This patch also synchronizes the structure changes to the Linux kernel.
The usages are searched by matching the following keywords:
1. acpi_resource_address
2. acpi_resource_extended_address
3. ACPI_RESOURCE_TYPE_ADDRESS
4. ACPI_RESOURCE_TYPE_EXTENDED_ADDRESS
And we found and fixed the usages in the following files:
arch/ia64/kernel/acpi-ext.c
arch/ia64/pci/pci.c
arch/x86/pci/acpi.c
arch/x86/pci/mmconfig-shared.c
drivers/xen/xen-acpi-memhotplug.c
drivers/acpi/acpi_memhotplug.c
drivers/acpi/pci_root.c
drivers/acpi/resource.c
drivers/char/hpet.c
drivers/pnp/pnpacpi/rsparser.c
drivers/hv/vmbus_drv.c
Build tests are passed with defconfig/allnoconfig/allyesconfig and
defconfig+CONFIG_ACPI=n.
Original-by: Thomas Gleixner <tglx@linutronix.de>
Original-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull x86 fixes from Thomas Gleixner:
"Hopefully the last round of fixes for 3.19
- regression fix for the LDT changes
- regression fix for XEN interrupt handling caused by the APIC
changes
- regression fixes for the PAT changes
- last minute fixes for new the MPX support
- regression fix for 32bit UP
- fix for a long standing relocation issue on 64bit tagged for stable
- functional fix for the Hyper-V clocksource tagged for stable
- downgrade of a pr_err which tends to confuse users
Looks a bit on the large side, but almost half of it are valuable
comments"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsc: Change Fast TSC calibration failed from error to info
x86/apic: Re-enable PCI_MSI support for non-SMP X86_32
x86, mm: Change cachemode exports to non-gpl
x86, tls: Interpret an all-zero struct user_desc as "no segment"
x86, tls, ldt: Stop checking lm in LDT_empty
x86, mpx: Strictly enforce empty prctl() args
x86, mpx: Fix potential performance issue on unmaps
x86, mpx: Explicitly disable 32-bit MPX support on 64-bit kernels
x86, hyperv: Mark the Hyper-V clocksource as being continuous
x86: Don't rely on VMWare emulating PAT MSR correctly
x86, irq: Properly tag virtualization entry in /proc/interrupts
x86, boot: Skip relocs when load address unchanged
x86/xen: Override ACPI IRQ management callback __acpi_unregister_gsi
ACPI: pci: Do not clear pci_dev->irq in acpi_pci_irq_disable()
x86/xen: Treat SCI interrupt as normal GSI interrupt
Xen overrides __acpi_register_gsi and leaves __acpi_unregister_gsi as is.
That means, an IRQ allocated by acpi_register_gsi_xen_hvm() or
acpi_register_gsi_xen() will be freed by acpi_unregister_gsi_ioapic(),
which may cause undesired effects. So override __acpi_unregister_gsi to
NULL for safety.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Cc: Tony Luck <tony.luck@intel.com>
Cc: xen-devel@lists.xenproject.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Graeme Gregory <graeme.gregory@linaro.org>
Cc: Lv Zheng <lv.zheng@intel.com>
Link: http://lkml.kernel.org/r/1421720467-7709-4-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently Xen Domain0 has special treatment for ACPI SCI interrupt,
that is initialize irq for ACPI SCI at early stage in a special way as:
xen_init_IRQ()
->pci_xen_initial_domain()
->xen_setup_acpi_sci()
Allocate and initialize irq for ACPI SCI
Function xen_setup_acpi_sci() calls acpi_gsi_to_irq() to get an irq
number for ACPI SCI. But unfortunately acpi_gsi_to_irq() depends on
IOAPIC irqdomains through following path
acpi_gsi_to_irq()
->mp_map_gsi_to_irq()
->mp_map_pin_to_irq()
->check IOAPIC irqdomain
For PV domains, it uses Xen event based interrupt manangement and
doesn't make uses of native IOAPIC, so no irqdomains created for IOAPIC.
This causes Xen domain0 fail to install interrupt handler for ACPI SCI
and all ACPI events will be lost. Please refer to:
https://lkml.org/lkml/2014/12/19/178
So the fix is to get rid of special treatment for ACPI SCI, just treat
ACPI SCI as normal GSI interrupt as:
acpi_gsi_to_irq()
->acpi_register_gsi()
->acpi_register_gsi_xen()
->xen_register_gsi()
With above change, there's no need for xen_setup_acpi_sci() anymore.
The above change also works with bare metal kernel too.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Cc: Tony Luck <tony.luck@intel.com>
Cc: xen-devel@lists.xenproject.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: http://lkml.kernel.org/r/1421720467-7709-2-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Every PCI-PCI bridge window should fit inside an upstream bridge window
because orphaned address space is unreachable from the primary side of the
upstream bridge. If we inherit invalid bridge windows that overlap an
upstream window from firmware, clip them to fit and update the bridge
accordingly.
[bhelgaas: changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Tested-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@redhat.com>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: x86@kernel.org
CC: stable@vger.kernel.org # v3.16+
access the mmcfg space - some error injection functions need to do
this.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3MwK
-----END PGP SIGNATURE-----
Merge tag 'please-pull-einj-mmcfg' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras into x86/ras
Pull RAS update from Tony Luck:
"When checking addresses in APEI action entries for validity, allow
access to the mmcfg space - some error injection functions need to do
this."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There are more that one SPI controller on the Intel MID boards. This patch
describes the status and IDs of them. From now on we also have to care about
bus number that must be unique per host.
According to the specification the SPI1 has 5 bits for chip selects and SPI2
only 2 bits. The patch makes it depend to PCI ID.
The first controller (SPI1) is DMA capable, meanwhile SPI2 can share same
channels (via software switch) such functionality is not in the scope of this
patch. Thus, attempt to init DMA for SPI2 will always fail for now.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull x86 apic updates from Thomas Gleixner:
"After stopping the full x86/apic branch, I took some time to go
through the first block of patches again, which are mostly cleanups
and preparatory work for the irqdomain conversion and ioapic hotplug
support.
Unfortunaly one of the real problematic commits was right at the
beginning, so I rebased this portion of the pending patches without
the offenders.
It would be great to get this into 3.19. That makes reworking the
problematic parts simpler. The usual tip testing did not unearth any
issues and it is fully bisectible now.
I'm pretty confident that this wont affect the calmness of the xmas
season.
Changes:
- Split the convoluted io_apic.c code into domain specific parts
(vector, ioapic, msi, htirq)
- Introduce proper helper functions to retrieve irq specific data
instead of open coded dereferencing of pointers
- Preparatory work for ioapic hotplug and irqdomain conversion
- Removal of the non functional pci-ioapic driver
- Removal of unused irq entry stubs
- Make native_smp_prepare_cpus() preemtible to avoid GFP_ATOMIC
allocations for everything which is called from there.
- Small cleanups and fixes"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
iommu/amd: Use helpers to access irq_cfg data structure associated with IRQ
iommu/vt-d: Use helpers to access irq_cfg data structure associated with IRQ
x86: irq_remapping: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Make MSI and HT_IRQ indepenent of X86_IO_APIC
x86, irq: Move IRQ initialization routines from io_apic.c into vector.c
x86, irq: Move IOAPIC related declarations from hw_irq.h into io_apic.h
x86, irq: Move HT IRQ related code from io_apic.c into htirq.c
x86, irq: Move PCI MSI related code from io_apic.c into msi.c
x86, irq: Replace printk(KERN_LVL) with pr_lvl() utilities
x86, irq: Make UP version of irq_complete_move() an inline stub
x86, irq: Move local APIC related code from io_apic.c into vector.c
x86, irq: Introduce helpers to access struct irq_cfg
x86, irq: Protect __clear_irq_vector() with vector_lock
x86, irq: Rename local APIC related functions in io_apic.c as apic_xxx()
x86, irq: Refine hw_irq.h to prepare for irqdomain support
x86, irq: Convert irq_2_pin list to generic list
x86, irq: Kill useless parameter 'irq_attr' of IO_APIC_get_PCI_irq_vector()
x86, irq, acpi: Get rid of special handling of GSI for ACPI SCI
x86, irq: Introduce helper to check whether an IOAPIC has been registered
...
None of the callers requires irq_attr to be filled
in. IO_APIC_get_PCI_irq_vector() does not do anything useful with it
either.
Remove the parameter and fixup the call sites.
[ tglx: Massaged changelog ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Ryan Desfosses <ryan@desfo.org>
Cc: Quentin Lambert <lambert.quentin@gmail.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: http://lkml.kernel.org/r/1414397531-28254-4-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To keep balance of IOAPIC pin reference count, we need to protect
pirq_enable_irq(), acpi_pci_irq_enable() and intel_mid_pci_irq_enable()
from reentrance. There are two cases which will cause reentrance.
The first case is caused by suspend/hibernation. If pcibios_disable_irq
is called during suspending/hibernating, we don't release the assigned
IRQ number, otherwise it may break the suspend/hibernation. So late when
pcibios_enable_irq is called during resume, we shouldn't allocate IRQ
number again.
The second case is that function acpi_pci_irq_enable() may be called
twice for PCI devices present at boot time as below:
1) pci_acpi_init()
--> acpi_pci_irq_enable() if pci_routeirq is true
2) pci_enable_device()
--> pcibios_enable_device()
--> acpi_pci_irq_enable()
We can't kill kernel parameter pci_routeirq yet because it's still
needed for debugging purpose.
So flag irq_managed is introduced to track whether IRQ number is
assigned by OS and to protect pirq_enable_irq(), acpi_pci_irq_enable()
and intel_mid_pci_irq_enable() from reentrance.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/1414387308-27148-13-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
While f3761db164 ("x86, irq: Fix build error caused by
9eabc99a635a77cbf09") addressed the original build problem,
declaration, inline stub, and definition still seem misplaced: It isn't
really IO-APIC related, and it's being used solely in arch/x86/pci/.
This also means stubbing it out when !CONFIG_X86_IO_APIC was at least
questionable.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Link: http://lkml.kernel.org/r/545747BE020000780004436E@mail.emea.novell.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some BIOSes utilize PCI MMCFG space read/write opertion to trigger
specific errors. EINJ will report errors as below when hitting such
cases:
APEI: Can not request [mem 0x83f990a0-0x83f990a3] for APEI EINJ Trigger registers
It is because on x86 platform ACPI based PCI MMCFG logic has
reserved all MMCFG spaces so that EINJ can't reserve it again.
We already trust the ACPI/APEI code when using the EINJ interface
so it is not a big leap to also trust it to access the right
MMCFG addresses. Skip address checking to allow the access.
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
- Fully support non-coherent devices on ARM by introducing the
mechanisms to request the hypervisor to perform the required cache
maintainance operations.
- A number of pciback bug fixes and cleanups. Notably a deadlock fix
if a PCI device was manually uunbound and a fix for incorrectly
restoring state after a function reset.
- In x86 PVHVM guests, use the APIC for interrupts if this has been
virtualized by the hardware. This reduces the number of interrupt-
related VM exits on such hardware.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJUiYb+AAoJEFxbo/MsZsTRwmEH+gNaJz5r8gIJlq8Q51+nOIs4
Gw6HdjUB5MOT47vDV4treEOx0Bk8hYTfgWUWvAC81JMJ1sMWOVrUGuG/0lmzaomW
zXvSk+o0n4LafwEhHb8LIccZMbaH7f9o3PNdNchrTkPrIl8Gf2nmBXCkDsT4mRye
5ZFpc4ntgBrznh3baPYDS8PCAmlyZ0uVEnz1ofYI6S80dC13siEiPG0c9TrNEKzO
glhvgCRmR0C4ZNLblM36HWBEqrdLuGCoNJSH+7okygyP2TLD3aO4R+9aD5JWYNdf
fO2WmivX/zK+UGVAElrLx+rb8R2dv3ddeaE5piZhIBUieopIWJd32L3LhQORdtc=
=N6DP
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.19-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen features and fixes from David Vrabel:
- Fully support non-coherent devices on ARM by introducing the
mechanisms to request the hypervisor to perform the required cache
maintainance operations.
- A number of pciback bug fixes and cleanups. Notably a deadlock fix
if a PCI device was manually uunbound and a fix for incorrectly
restoring state after a function reset.
- In x86 PVHVM guests, use the APIC for interrupts if this has been
virtualized by the hardware. This reduces the number of interrupt-
related VM exits on such hardware.
* tag 'stable/for-linus-3.19-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (26 commits)
Revert "swiotlb-xen: pass dev_addr to swiotlb_tbl_unmap_single"
xen/pci: Use APIC directly when APIC virtualization hardware is available
xen/pci: Defer initialization of MSI ops on HVM guests
xen-pciback: drop SR-IOV VFs when PF driver unloads
xen/pciback: Restore configuration space when detaching from a guest.
PCI: Expose pci_load_saved_state for public consumption.
xen/pciback: Remove tons of dereferences
xen/pciback: Print out the domain owning the device.
xen/pciback: Include the domain id if removing the device whilst still in use
driver core: Provide an wrapper around the mutex to do lockdep warnings
xen/pciback: Don't deadlock when unbinding.
swiotlb-xen: pass dev_addr to swiotlb_tbl_unmap_single
swiotlb-xen: call xen_dma_sync_single_for_device when appropriate
swiotlb-xen: remove BUG_ON in xen_bus_to_phys
swiotlb-xen: pass dev_addr to xen_dma_unmap_page and xen_dma_sync_single_for_cpu
xen/arm: introduce GNTTABOP_cache_flush
xen/arm/arm64: introduce xen_arch_need_swiotlb
xen/arm/arm64: merge xen/mm32.c into xen/mm.c
xen/arm: use hypercall to flush caches in map_page
xen: add a dma_addr_t dev_addr argument to xen_dma_map_page
...
Pull x86 mm tree changes from Ingo Molnar:
"The biggest change is full PAT support from Jürgen Gross:
The x86 architecture offers via the PAT (Page Attribute Table) a
way to specify different caching modes in page table entries. The
PAT MSR contains 8 entries each specifying one of 6 possible cache
modes. A pte references one of those entries via 3 bits:
_PAGE_PAT, _PAGE_PWT and _PAGE_PCD.
The Linux kernel currently supports only 4 different cache modes.
The PAT MSR is set up in a way that the setting of _PAGE_PAT in a
pte doesn't matter: the top 4 entries in the PAT MSR are the same
as the 4 lower entries.
This results in the kernel not supporting e.g. write-through mode.
Especially this cache mode would speed up drivers of video cards
which now have to use uncached accesses.
OTOH some old processors (Pentium) don't support PAT correctly and
the Xen hypervisor has been using a different PAT MSR configuration
for some time now and can't change that as this setting is part of
the ABI.
This patch set abstracts the cache mode from the pte and introduces
tables to translate between cache mode and pte bits (the default
cache mode "write back" is hard-wired to PAT entry 0). The tables
are statically initialized with values being compatible to old
processors and current usage. As soon as the PAT MSR is changed
(or - in case of Xen - is read at boot time) the tables are changed
accordingly. Requests of mappings with special cache modes are
always possible now, in case they are not supported there will be a
fallback to a compatible but slower mode.
Summing it up, this patch set adds the following features:
- capability to support WT and WP cache modes on processors with
full PAT support
- processors with no or uncorrect PAT support are still working as
today, even if WT or WP cache mode are selected by drivers for
some pages
- reduction of Xen special handling regarding cache mode
Another change is a boot speedup on ridiculously large RAM systems,
plus other smaller fixes"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
x86: mm: Move PAT only functions to mm/pat.c
xen: Support Xen pv-domains using PAT
x86: Enable PAT to use cache mode translation tables
x86: Respect PAT bit when copying pte values between large and normal pages
x86: Support PAT bit in pagetable dump for lower levels
x86: Clean up pgtable_types.h
x86: Use new cache mode type in memtype related functions
x86: Use new cache mode type in mm/ioremap.c
x86: Use new cache mode type in setting page attributes
x86: Remove looking for setting of _PAGE_PAT_LARGE in pageattr.c
x86: Use new cache mode type in track_pfn_remap() and track_pfn_insert()
x86: Use new cache mode type in mm/iomap_32.c
x86: Use new cache mode type in asm/pgtable.h
x86: Use new cache mode type in arch/x86/mm/init_64.c
x86: Use new cache mode type in arch/x86/pci
x86: Use new cache mode type in drivers/video/fbdev/vermilion
x86: Use new cache mode type in drivers/video/fbdev/gbefb.c
x86: Use new cache mode type in include/asm/fb.h
x86: Make page cache mode a real type
x86: mm: Use 2GB memory block size on large-memory x86-64 systems
...
Pull x86 platform changes from Ingo Molnar:
"A handful of numachip APIC driver updates/fixes, and two small SGI/UV
fixes"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: numachip: APIC driver cleanups
x86: numachip: Elide self-IPI ICR polling
x86: numachip: Fix 16-bit APIC ID truncation
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: UV BAU: Increase maximum CPUs per socket/hub
x86: UV BAU: Avoid NULL pointer reference in ptc_seq_show
When hardware supports APIC/x2APIC virtualization we don't need to use
pirqs for MSI handling and instead use APIC since most APIC accesses
(MMIO or MSR) will now be processed without VMEXITs.
As an example, netperf on the original code produces this profile
(collected wih 'xentrace -e 0x0008ffff -T 5'):
342 cpu_change
260 CPUID
34638 HLT
64067 INJ_VIRQ
28374 INTR
82733 INTR_WINDOW
10 NPF
24337 TRAP
370610 vlapic_accept_pic_intr
307528 VMENTRY
307527 VMEXIT
140998 VMMCALL
127 wrap_buffer
After applying this patch the same test shows
230 cpu_change
260 CPUID
36542 HLT
174 INJ_VIRQ
27250 INTR
222 INTR_WINDOW
20 NPF
24999 TRAP
381812 vlapic_accept_pic_intr
166480 VMENTRY
166479 VMEXIT
77208 VMMCALL
81 wrap_buffer
ApacheBench results (ab -n 10000 -c 200) improve by about 10%
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
If the hardware supports APIC virtualization we may decide not to use
pirqs and instead use APIC/x2APIC directly, meaning that we don't want
to set x86_msi.setup_msi_irqs and x86_msi.teardown_msi_irq to
Xen-specific routines. However, x2APIC is not set up by the time
pci_xen_hvm_init() is called so we need to postpone setting these ops
until later, when we know which APIC mode is used.
(Note that currently x2APIC is never initialized on HVM guests. This
may change in the future)
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Rename write_msi_msg() to pci_write_msi_msg() to mark it as PCI
specific.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rename __read_msi_msg() to __pci_read_msi_msg() and kill unused
read_msi_msg(). It's a preparation to separate generic MSI code from
PCI core.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The problem fixed by 0e4ccb1505 ("PCI: Add x86_msi.msi_mask_irq() and
msix_mask_irq()") has been fixed in a simpler way by a previous commit
("PCI/MSI: Add pci_msi_ignore_mask to prevent writes to MSI/MSI-X Mask
Bits").
The msi_mask_irq() and msix_mask_irq() x86_msi_ops added by 0e4ccb1505
are no longer needed, so revert the commit.
default_msi_mask_irq() and default_msix_mask_irq() were added by
0e4ccb1505 and are still used by s390, so keep them for now.
[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: xen-devel@lists.xenproject.org
MSI-X vector Mask Bits are in MSI-X Tables in PCI memory space. Xen PV
guests can't write to those tables. MSI vector Mask Bits are in PCI
configuration space. Xen PV guests can write to config space, but those
writes are ignored.
Commit 0e4ccb1505 ("PCI: Add x86_msi.msi_mask_irq() and
msix_mask_irq()") added a way to override default_mask_msi_irqs() and
default_mask_msix_irqs() so they can be no-ops in Xen guests, but this is
more complicated than necessary.
Add "pci_msi_ignore_mask" in the core PCI MSI code. If set,
default_mask_msi_irqs() and default_mask_msix_irqs() return without doing
anything. This is less flexible, but much simpler.
[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: xen-devel@lists.xenproject.org
Drop printing that serves no purpose, as it's printing fixed or known
values, and mark constant structure appropriately.
Signed-off-by: Daniel J Blueman <daniel@numascale.com>
Cc: Steffen Persvold <sp@numascale.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: http://lkml.kernel.org/r/1415089784-28779-3-git-send-email-daniel@numascale.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- Add pvscsi frontend and backend drivers.
- Remove _PAGE_IOMAP PTE flag, freeing it for alternate uses.
- Try and keep memory contiguous during PV memory setup (reduces
SWIOTLB usage).
- Allow front/back drivers to use threaded irqs.
- Support large initrds in PV guests.
- Fix PVH guests in preparation for Xen 4.5
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJUNonmAAoJEFxbo/MsZsTRHAQH/inCjpCT+pkvTB0YAVfVvgMI
gUogT8G+iB2MuCNpMffGIt8TAVXwcVtnOLH9ABH3IBVehzgipIbIiVEM9YhjrYvU
1rgIKBpmZqSpjDHoIHpdHeCH67cVnRzA/PyoxZWLxPNmQ0t6bNf9yeAcCXK9PfUc
7EAblUDmPGSx9x/EUnOKNNaZSEiUJZHDBXbMBLllk1+5H1vfKnpFCRGMG0IrfI44
KVP2NX9Gfa05edMZYtH887FYyjFe2KNV6LJvE7+w7h2Dy0yIzf7y86t0l4n8gETb
plvEUJ/lu9RYzTiZY/RxgBFYVTV59EqT45brSUtoe2Jcp8GSwiHslTHdfyFBwSo=
=gw4d
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.18-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen updates from David Vrabel:
"Features and fixes:
- Add pvscsi frontend and backend drivers.
- Remove _PAGE_IOMAP PTE flag, freeing it for alternate uses.
- Try and keep memory contiguous during PV memory setup (reduces
SWIOTLB usage).
- Allow front/back drivers to use threaded irqs.
- Support large initrds in PV guests.
- Fix PVH guests in preparation for Xen 4.5"
* tag 'stable/for-linus-3.18-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (22 commits)
xen: remove DEFINE_XENBUS_DRIVER() macro
xen/xenbus: Remove BUG_ON() when error string trucated
xen/xenbus: Correct the comments for xenbus_grant_ring()
x86/xen: Set EFER.NX and EFER.SCE in PVH guests
xen: eliminate scalability issues from initrd handling
xen: sync some headers with xen tree
xen: make pvscsi frontend dependant on xenbus frontend
arm{,64}/xen: Remove "EXPERIMENTAL" in the description of the Xen options
xen-scsifront: don't deadlock if the ring becomes full
x86: remove the Xen-specific _PAGE_IOMAP PTE flag
x86/xen: do not use _PAGE_IOMAP PTE flag for I/O mappings
x86: skip check for spurious faults for non-present faults
xen/efi: Directly include needed headers
xen-scsiback: clean up a type issue in scsiback_make_tpg()
xen-scsifront: use GFP_ATOMIC under spin_lock
MAINTAINERS: Add xen pvscsi maintainer
xen-scsiback: Add Xen PV SCSI backend driver
xen-scsifront: Add Xen PV SCSI frontend driver
xen: Add Xen pvSCSI protocol description
xen/events: support threaded irqs for interdomain event channels
...
The pci_find_bios() function is only ever called from initialization code,
therefore can be marked as such, too. This, in turn, allows marking other
functions called only in this context as well.
The bios32_indirect variable can be marked as __initdata as it is only
referenced from __init functions now.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
The pci_mmcfg_probes[] array is only ever read, therefore make it const.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
The constants in pci_mmcfg_nvidia_mcp55() need to be marked as __initconst
or they will remain in memory after init memory was released.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
According to include/linux/init.h, the __init annotation should be added
immediately before the function name. However, for quite a few functions
in mmconfig-shared.c this is not the case. It's either before the return
type or even in the middle of it. Beside gcc still getting it right, we
should change them to comply to the rules of include/linux/init.h.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
The _PAGE_IO_MAP PTE flag was only used by Xen PV guests to mark PTEs
that were used to map I/O regions that are 1:1 in the p2m. This
allowed Xen to obtain the correct PFN when converting the MFNs read
from a PTE back to their PFN.
Xen guests no longer use _PAGE_IOMAP for this. Instead mfn_to_pfn()
returns the correct PFN by using a combination of the m2p and p2m to
determine if an MFN corresponds to a 1:1 mapping in the the p2m.
Remove _PAGE_IOMAP, replacing it with _PAGE_UNUSED2 to allow for
future uses of the PTE flag.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
The DMI tables are only used in __init code, thereby can be marked as
initialization data, too. The same is true for the callback functions
referenced from the DMI tables.
This moves ~9.6 kB of code and r/o data to the init sections, marking the
memory for release after initialization.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Enumeration
- Don't default exclusively to first video device (Bruno Prémont)
PCI device hotplug
- Remove "no hotplug settings from platform" warning (Bjorn Helgaas)
- Add pci_ignore_hotplug() for VGA switcheroo (Bjorn Helgaas)
Freescale i.MX6
- Put LTSSM in "Detect" state before disabling (Lucas Stach)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xIYe
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These fix:
- Boot video device detection on dual-GPU Apple systems
- Hotplug fiascos on VGA switcheroo with radeon & nouveau drivers
- Boot hang on Freescale i.MX6 systems
- Excessive "no hotplug settings from platform" warnings
In particular:
Enumeration
- Don't default exclusively to first video device (Bruno Prémont)
PCI device hotplug
- Remove "no hotplug settings from platform" warning (Bjorn Helgaas)
- Add pci_ignore_hotplug() for VGA switcheroo (Bjorn Helgaas)
Freescale i.MX6
- Put LTSSM in "Detect" state before disabling (Lucas Stach)"
* tag 'pci-v3.17-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
vgaarb: Drop obsolete #ifndef
vgaarb: Don't default exclusively to first video device with mem+io
ACPIPHP / radeon / nouveau: Remove acpi_bus_no_hotplug()
PCI: Remove "no hotplug settings from platform" warning
PCI: Add pci_ignore_hotplug() to ignore hotplug events for a device
PCI: imx6: Put LTSSM in "Detect" state before disabling it
MAINTAINERS: Add Lucas Stach as co-maintainer for i.MX6 PCI driver
Commit 20cde69402 ("x86, ia64: Move EFI_FB vga_default_device()
initialization to pci_vga_fixup()") moved boot video device detection from
efifb to x86 and ia64 pci/fixup.c.
For dual-GPU Apple computers above change represents a regression as code
in efifb did forcefully override vga_default_device while the merge did not
(vgaarb happens prior to PCI fixup).
To improve on initial device selection by vgaarb (it cannot know if PCI
device not behind bridges see/decode legacy VGA I/O or not), move the
screen_info based check from pci_video_fixup() to vgaarb's init function and
use it to refine/override decision taken while adding the individual PCI
VGA devices. This way PCI fixup has no reason to adjust vga_default_device
anymore but can depend on its value for flagging shadowed VBIOS.
This has the nice benefit of removing duplicated code but does introduce a
#if defined() block in vgaarb. Not all architectures have screen_info and
would cause compile to fail without it.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=84461
Reported-and-Tested-By: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Matthew Garrett <matthew.garrett@nebula.com>
CC: stable@vger.kernel.org # v3.5+
Now IOAPIC driver dynamically allocates IRQ numbers for IOAPIC pins.
We need to keep IRQ assignment for PCI devices during runtime power
management, otherwise it may cause failure of device wakeups.
Commit 3eec595235 "x86, irq, PCI: Keep IRQ assignment for PCI
devices during suspend/hibernation" has fixed the issue for suspend/
hibernation, we also need the same fix for runtime device sleep too.
Fix: https://bugzilla.kernel.org/show_bug.cgi?id=83271
Reported-and-Tested-by: EmanueL Czirai <amanual@openmailbox.org>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: EmanueL Czirai <amanual@openmailbox.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1409304383-18806-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull x86/apic updates from Thomas Gleixner:
"This is a major overhaul to the x86 apic subsystem consisting of the
following parts:
- Remove obsolete APIC driver abstractions (David Rientjes)
- Use the irqdomain facilities to dynamically allocate IRQs for
IOAPICs. This is a prerequisite to enable IOAPIC hotplug support,
and it also frees up wasted vectors (Jiang Liu)
- Misc fixlets.
Despite the hickup in Ingos previous pull request - caused by the
missing fixup for the suspend/resume issue reported by Borislav - I
strongly recommend that this update finds its way into 3.17. Some
history for you:
This is preparatory work for physical IOAPIC hotplug. The first
attempt to support this was done by Yinghai and I shot it down because
it just added another layer of obscurity and complexity to the already
existing mess without tackling the underlying shortcomings of the
current implementation.
After quite some on- and offlist discussions, I requested that the
design of this functionality must use generic infrastructure, i.e.
irq domains, which provide all the mechanisms to dynamically map linux
interrupt numbers to physical interrupts.
Jiang picked up the idea and did a great job of consolidating the
existing interfaces to manage the x86 (IOAPIC) interrupt system by
utilizing irq domains.
The testing in tip, Linux-next and inside of Intel on various machines
did not unearth any oddities until Borislav exposed it to one of his
oddball machines. The issue was resolved quickly, but unfortunately
the fix fell through the cracks and did not hit the tip tree before
Ingo sent the pull request. Not entirely Ingos fault, I also assumed
that the fix was already merged when Ingo asked me whether he could
send it.
Nevertheless this work has a proper design, has undergone several
rounds of review and the final fallout after applying it to tip and
integrating it into Linux-next has been more than moderate. It's the
ground work not only for IOAPIC hotplug, it will also allow us to move
the lowlevel vector allocation into the irqdomain hierarchy, which
will benefit other architectures as well. Patches are posted already,
but they are on hold for two weeks, see below.
I really appreciate the competence and responsiveness Jiang has shown
in course of this endavour. So I'm sure that any fallout of this will
be addressed in a timely manner.
FYI, I'm vanishing for 2 weeks into my annual kids summer camp kitchen
duty^Wvacation, while you folks are drooling at KS/LinuxCon :) But HPA
will have a look at the hopefully zero fallout until I'm back"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (53 commits)
x86, irq, PCI: Keep IRQ assignment for PCI devices during suspend/hibernation
x86/apic/vsmp: Make is_vsmp_box() static
x86, apic: Remove enable_apic_mode callback
x86, apic: Remove setup_portio_remap callback
x86, apic: Remove multi_timer_check callback
x86, apic: Replace noop_check_apicid_used
x86, apic: Remove check_apicid_present callback
x86, apic: Remove mps_oem_check callback
x86, apic: Remove smp_callin_clear_local_apic callback
x86, apic: Replace trampoline physical addresses with defaults
x86, apic: Remove x86_32_numa_cpu_node callback
x86: intel-mid: Use the new io_apic interfaces
x86, vsmp: Remove is_vsmp_box() from apic_is_clustered_box()
x86, irq: Clean up irqdomain transition code
x86, irq, devicetree: Release IOAPIC pin when PCI device is disabled
x86, irq, SFI: Release IOAPIC pin when PCI device is disabled
x86, irq, mpparse: Release IOAPIC pin when PCI device is disabled
x86, irq, ACPI: Release IOAPIC pin when PCI device is disabled
x86, irq: Introduce helper functions to release IOAPIC pin
x86, irq: Simplify the way to handle ISA IRQ
...
Now IOAPIC driver dynamically allocates IRQ numbers for IOAPIC pins.
We need to keep IRQ assignment for PCI devices during suspend/hibernation,
otherwise it may cause failure of suspend/hibernation due to:
1) Device driver calls pci_enable_device() to allocate an IRQ number
and register interrupt handler on the returned IRQ.
2) Device driver's suspend callback calls pci_disable_device() and
release assigned IRQ in turn.
3) Device driver's resume callback calls pci_enable_device() to
allocate IRQ number again. A different IRQ number may be assigned
by IOAPIC driver this time.
4) Now the hardware delivers interrupt to the new IRQ but interrupt
handler is still registered against the old IRQ, so it breaks
suspend/hibernation.
To fix this issue, we keep IRQ assignment during suspend/hibernation.
Flag pci_dev.dev.power.is_prepared is used to detect that
pci_disable_device() is called during suspend/hibernation.
Reported-and-Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/1407478071-29399-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 30919b0bf3 ("x86: avoid low BIOS area when allocating address
space") moved the test for resource allocations that fall within the first
1MB of address space from the PCI-specific path to a generic path, such
that all resource allocations will avoid this area. However, this breaks
ISA cards which need to allocate a memory region within the first 1MB. An
example is the i82365 PCMCIA controller and derivatives like the Ricoh
RF5C296/396 which map part of the PCMCIA socket memory address space into
the first 1MB of system memory address space. They do not work anymore as
no usable memory region exists due to this change:
Intel ISA PCIC probe: Ricoh RF5C296/396 ISA-to-PCMCIA at port 0x3e0 ofs 0x00, 2 sockets
host opts [0]: none
host opts [1]: none
ISA irqs (scanned) = 3,4,5,9,10 status change on irq 10
pcmcia_socket pcmcia_socket1: pccard: PCMCIA card inserted into slot 1
pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff
pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3ff: excluding 0x170-0x177 0x1f0-0x1f7 0x2f8-0x2ff 0x370-0x37f 0x3c0-0x3e7 0x3f0-0x3ff
pcmcia_socket pcmcia_socket0: cs: memory probe 0x0a0000-0x0affff: excluding 0xa0000-0xaffff
pcmcia_socket pcmcia_socket0: cs: memory probe 0x0b0000-0x0bffff: excluding 0xb0000-0xbffff
pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0cffff: excluding 0xc0000-0xcbfff
pcmcia_socket pcmcia_socket0: cs: memory probe 0x0d0000-0x0dffff: clean.
pcmcia_socket pcmcia_socket0: cs: memory probe 0x0e0000-0x0effff: clean.
pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff: clean.
pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: clean.
pcmcia_socket pcmcia_socket1: cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff
pcmcia_socket pcmcia_socket1: cs: IO port probe 0xa00-0xaff: clean.
pcmcia_socket pcmcia_socket1: cs: IO port probe 0x100-0x3ff: excluding 0x170-0x177 0x1f0-0x1f7 0x2f8-0x2ff 0x370-0x37f 0x3c0-0x3e7 0x3f0-0x3ff
pcmcia_socket pcmcia_socket1: cs: memory probe 0x0a0000-0x0affff: excluding 0xa0000-0xaffff
pcmcia_socket pcmcia_socket1: cs: memory probe 0x0b0000-0x0bffff: excluding 0xb0000-0xbffff
pcmcia_socket pcmcia_socket1: cs: memory probe 0x0c0000-0x0cffff: excluding 0xc0000-0xcbfff
pcmcia_socket pcmcia_socket1: cs: memory probe 0x0d0000-0x0dffff: clean.
pcmcia_socket pcmcia_socket1: cs: memory probe 0x0e0000-0x0effff: clean.
pcmcia_socket pcmcia_socket1: cs: memory probe 0x60000000-0x60ffffff: clean.
pcmcia_socket pcmcia_socket1: cs: memory probe 0xa0000000-0xa0ffffff: clean.
pcmcia_socket pcmcia_socket1: cs: memory probe 0x0cc000-0x0effff: excluding 0xe0000-0xeffff
pcmcia_socket pcmcia_socket1: cs: unable to map card memory!
If filtering out the first 1MB is reverted, everything works as expected.
Tested-by: Robert Resch <fli4l@robert.reschpara.de>
Signed-off-by: Christoph Schulz <develop@kristov.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v2.6.37+
Commit b4aa016305 ("efifb: Implement vga_default_device() (v2)") added
efifb vga_default_device() so EFI systems that do not load shadow VBIOS or
setup VGA get proper value for boot_vga PCI sysfs attribute on the
corresponding PCI device.
Xorg doesn't detect devices when boot_vga=0, e.g., on some EFI systems such
as MacBookAir2,1. Xorg detects the GPU and finds the DRI device but then
bails out with "no devices detected".
Note: When vga_default_device() is set boot_vga PCI sysfs attribute
reflects its state. When unset this attribute is 1 whenever
IORESOURCE_ROM_SHADOW flag is set.
With introduction of sysfb/simplefb/simpledrm efifb is getting obsolete
while having native drivers for the GPU also makes selecting sysfb/efifb
optional.
Remove the efifb implementation of vga_default_device() and initialize
vgaarb's vga_default_device() with the PCI GPU that matches boot
screen_info in pci_fixup_video().
[bhelgaas: remove unused "dev" in efifb_setup()]
Fixes: b4aa016305 ("efifb: Implement vga_default_device() (v2)")
Tested-by: Anibal Francisco Martinez Cortina <linuxkid.zeuz@gmail.com>
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Matthew Garrett <matthew.garrett@nebula.com>
CC: stable@vger.kernel.org # v3.5+
Release IOAPIC pin associated with PCI device when the PCI device
is disabled.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1402302011-23642-41-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Release IOAPIC pin associated with PCI device when the PCI device
is disabled.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1402302011-23642-40-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Refine SFI to use common irqdomain map interface to program IOAPIC pins,
so we can unify the callsite to progam IOAPIC pins.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: sfi-devel@simplefirmware.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Link: http://lkml.kernel.org/r/1402302011-23642-33-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Refine mpparse to use common irqdomain map interface to program IOAPIC pins,
so we can unify the callsite to progam IOAPIC pins.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1402302011-23642-32-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Enhance SFI to provide basic support of irqdomain with identity mapping
between GSIs and IRQs.
Some Intel MID platforms assumes identity mapping between GSI and IRQ,
so we can't dynamically allocate IRQ number on demand.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: sfi-devel@simplefirmware.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Link: http://lkml.kernel.org/r/1402302011-23642-28-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some platforms, such as Intel MID and mshypv, do not support legacy
interrupt controllers. So count legacy IRQs by legacy_pic->nr_legacy_irqs
instead of hard-coded NR_IRQS_LEGACY.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: xen-devel@lists.xenproject.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
Link: http://lkml.kernel.org/r/1402302011-23642-20-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use kmalloc_node() instead of kmalloc() when possible to optimize
for performance on NUMA platforms.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1402302011-23642-6-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The DMA Contiguous Memory Allocator support on x86 is disabled when
swiotlb config option is enabled. So DMA CMA is always disabled on
x86_64 because swiotlb is always enabled. This attempts to support for
DMA CMA with enabling swiotlb config option.
The contiguous memory allocator on x86 is integrated in the function
dma_generic_alloc_coherent() which is .alloc callback in nommu_dma_ops
for dma_alloc_coherent().
x86_swiotlb_alloc_coherent() which is .alloc callback in swiotlb_dma_ops
tries to allocate with dma_generic_alloc_coherent() firstly and then
swiotlb_alloc_coherent() is called as a fallback.
The main part of supporting DMA CMA with swiotlb is that changing
x86_swiotlb_free_coherent() which is .free callback in swiotlb_dma_ops
for dma_free_coherent() so that it can distinguish memory allocated by
dma_generic_alloc_coherent() from one allocated by
swiotlb_alloc_coherent() and release it with dma_generic_free_coherent()
which can handle contiguous memory. This change requires making
is_swiotlb_buffer() global function.
This also needs to change .free callback in the dma_map_ops for amd_gart
and sta2x11, because these dma_ops are also using
dma_generic_alloc_coherent().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Don Dutile <ddutile@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* pci/hotplug:
PCI: cpqphp: Fix possible null pointer dereference
NVMe: Implement PCIe reset notification callback
PCI: Notify driver before and after device reset
* pci/pci_is_bridge:
pcmcia: Use pci_is_bridge() to simplify code
PCI: pciehp: Use pci_is_bridge() to simplify code
PCI: acpiphp: Use pci_is_bridge() to simplify code
PCI: cpcihp: Use pci_is_bridge() to simplify code
PCI: shpchp: Use pci_is_bridge() to simplify code
PCI: rpaphp: Use pci_is_bridge() to simplify code
sparc/PCI: Use pci_is_bridge() to simplify code
powerpc/PCI: Use pci_is_bridge() to simplify code
ia64/PCI: Use pci_is_bridge() to simplify code
x86/PCI: Use pci_is_bridge() to simplify code
PCI: Use pci_is_bridge() to simplify code
PCI: Add new pci_is_bridge() interface
PCI: Rename pci_is_bridge() to pci_has_subordinate()
* pci/virtualization:
PCI: Introduce new device binding path using pci_dev.driver_override
Conflicts:
drivers/pci/pci-sysfs.c
* pci/host-exynos:
PCI: exynos: Remove unnecessary OOM messages
* pci/host-rcar:
PCI: rcar: Add gen2 device tree support
PCI: rcar: Add R-Car PCIe device tree bindings
PCI: rcar: Add MSI support for PCIe
PCI: rcar: Add Renesas R-Car PCIe driver
PCI: rcar: Use new OF interrupt mapping when possible
* pci/amd-numa:
x86/PCI: Clean up and mark early_root_info_init() as deprecated
x86/PCI: Work around AMD Fam15h BIOSes that fail to provide _PXM
x86/PCI: Warn if we have to "guess" host bridge node information
Use pci_is_bridge() to simplify code. No functional change.
Requires: 326c1cdae7 PCI: Rename pci_is_bridge() to pci_has_subordinate()
Requires: 1c86438c94 PCI: Add new pci_is_bridge() interface
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
early_root_info_init() is now deprecated in favor of info in ACPI. Add a
note to that effect. Also, clean up the code a bit.
There is no functional change.
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move the pcibios_assign_resources() fs_initcall annotation next to the
function definition. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The BIOS is supposed to provide ACPI _PXM methods for PCI host bridges if
it cares about platform topology. But some BIOSes do not, so add Fam15h
to the list of CPUs for which we fall back to reading node numbers from the
hardware.
Note that pci_acpi_scan_root() warns about the BIOS bug if we use this
information because (1) the hardware node numbers are not necessarily
compatible with other logical node numbers from ACPI, and (2) the lack of
_PXM forces OS updates that would not otherwise be required.
[bhelgaas: changelog, comments]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=72051
Tested-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Robert Richter <rric@kernel.org>
Cc: Daniel J Blueman <daniel@numascale.com>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
The vast majority of platforms are not supplying ACPI _PXM (proximity)
information corresponding to host bridge (PNP0A03/PNP0A08) devices
resulting in sysfs "numa_node" values of -1 (NUMA_NO_NODE):
# for i in /sys/devices/pci0000\:00/*/numa_node; do cat $i; done | uniq
-1
# find /sys/ -name "numa_node" | while read fname; do cat $fname; \
done | uniq
-1
AMD based platforms provide a fall-back for this situation via amd_bus.c.
These platforms snoop out the information by directly reading specific
registers from the Northbridge and caching them via alloc_pci_root_info().
Later during boot processing when host bridges are discovered -
pci_acpi_scan_root() - the kernel looks for their corresponding ACPI _PXM
method - drivers/acpi/numa.c::acpi_get_node(). If the BIOS supplied a _PXM
method then that node (proximity) value is associated. If the BIOS did not
supply a _PXM method *and* the platform is AMD-based, the fall-back cached
values obtained directly from the Northbridge are used; otherwise,
"NUMA_NO_NODE" is associated.
There are a number of issues with this fall-back mechanism the most notable
being that amd_bus.c extracts a 3-bit number from a CPU register and uses
it as the node number. The node numbers used by Linux are logical and
there's no reason they need to be identical to settings in the CPU
registers. So if we have some node information obtained in the normal way
(from _PXM, SLIT, SRAT, etc.) and some from amd_bus.c, there's no reason to
believe they will be compatible.
This patch warns when this situation occurs:
pci_root PNP0A08:00: [Firmware Bug]: no _PXM; falling back to node 0 from hardware (may be inconsistent with ACPI node numbers)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=72051
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Bodo reported that on the Asrock M3A UCC, v3.12.6 hangs during boot unless
he uses "pci=nocrs". This regression was caused by 7bc5e3f2be ("x86/PCI:
use host bridge _CRS info by default on 2008 and newer machines"), which
appeared in v2.6.34.
The reason is that the HPET address appears in a PCI device BAR, and this
address is not contained in any of the host bridge windows. Linux moves
the PCI BAR into a window, but the original address was published via the
HPET table and an ACPI device, so changing the BAR is a bad idea. Here's
the dmesg info:
ACPI: HPET id: 0x43538301 base: 0xfed00000
pci_root PNP0A03:00: host bridge window [mem 0xd0000000-0xdfffffff]
pci_root PNP0A03:00: host bridge window [mem 0xf0000000-0xfebfffff]
pci 0000:00:14.0: [1002:4385] type 0 class 0x000c05
pci 0000:00:14.0: reg 14: [mem 0xfed00000-0xfed003ff]
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
pnp 00:06: Plug and Play ACPI device, IDs PNP0103 (active)
pnp 00:06: [mem 0xfed00000-0xfed003ff]
When we notice the BAR is not in a host bridge window, we try to move it,
but that causes a hang shortly thereafter:
pci 0000:00:14.0: no compatible bridge window for [mem 0xfed00000-0xfed003ff]
pci 0000:00:14.0: BAR 1: assigned [mem 0xf0000000-0xf00003ff]
This patch marks the BAR as IORESOURCE_PCI_FIXED to prevent Linux from
moving it. This depends on a previous patch ("x86/PCI: Don't try to move
IORESOURCE_PCI_FIXED resources") to check for this flag when
pci_claim_resource() fails.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=68591
Reported-and-tested-by: Bodo Eggert <7eggert@gmx.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Don't attempt to move resource marked IORESOURCE_PCI_FIXED, even if
pci_claim_resource() fails. In some cases, these are legacy resources that
cannot be moved.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In the expression "word1 << 16", word1 starts as u16, but is promoted to
a signed int, then sign-extended to resource_size_t, which is probably
not what was intended. Cast to resource_size_t to avoid the sign
extension.
Found by Coverity (CID 138749, 138750).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The purpose of this single series of commits from Srivatsa S Bhat (with
a small piece from Gautham R Shenoy) touching multiple subsystems that use
CPU hotplug notifiers is to provide a way to register them that will not
lead to deadlocks with CPU online/offline operations as described in the
changelog of commit 93ae4f978c (CPU hotplug: Provide lockless versions
of callback registration functions).
The first three commits in the series introduce the API and document it
and the rest simply goes through the users of CPU hotplug notifiers and
converts them to using the new method.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=SW7Q
-----END PGP SIGNATURE-----
Merge tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull CPU hotplug notifiers registration fixes from Rafael Wysocki:
"The purpose of this single series of commits from Srivatsa S Bhat
(with a small piece from Gautham R Shenoy) touching multiple
subsystems that use CPU hotplug notifiers is to provide a way to
register them that will not lead to deadlocks with CPU online/offline
operations as described in the changelog of commit 93ae4f978c ("CPU
hotplug: Provide lockless versions of callback registration
functions").
The first three commits in the series introduce the API and document
it and the rest simply goes through the users of CPU hotplug notifiers
and converts them to using the new method"
* tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (52 commits)
net/iucv/iucv.c: Fix CPU hotplug callback registration
net/core/flow.c: Fix CPU hotplug callback registration
mm, zswap: Fix CPU hotplug callback registration
mm, vmstat: Fix CPU hotplug callback registration
profile: Fix CPU hotplug callback registration
trace, ring-buffer: Fix CPU hotplug callback registration
xen, balloon: Fix CPU hotplug callback registration
hwmon, via-cputemp: Fix CPU hotplug callback registration
hwmon, coretemp: Fix CPU hotplug callback registration
thermal, x86-pkg-temp: Fix CPU hotplug callback registration
octeon, watchdog: Fix CPU hotplug callback registration
oprofile, nmi-timer: Fix CPU hotplug callback registration
intel-idle: Fix CPU hotplug callback registration
clocksource, dummy-timer: Fix CPU hotplug callback registration
drivers/base/topology.c: Fix CPU hotplug callback registration
acpi-cpufreq: Fix CPU hotplug callback registration
zsmalloc: Fix CPU hotplug callback registration
scsi, fcoe: Fix CPU hotplug callback registration
scsi, bnx2fc: Fix CPU hotplug callback registration
scsi, bnx2i: Fix CPU hotplug callback registration
...
kernel-based backends (by not populated m2p overrides when mapping),
and assorted minor bug fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQEcBAABAgAGBQJTPTGyAAoJEFxbo/MsZsTRnjgH/10j5CbOK1RFvIyCSslGTf4G
slhK8P8dhhplGAxwXXji322lWNYEx9Jd+V0Bhxnvr4drSlsP/qkWuBWf+u1LBvRq
AVPM99tk0XHCVAuvMMNo/lc62dTIR9IpQvnY6WhHSHnSlfqyVcdnbaGk8/LRuxWJ
u2F0MXzDNH00b/kt6hDBt3F7CkHfjwsEn43LCkkxyHPp5MJGD7bGDIe+bKtnjv9u
D9VJtCWQkrjWQ6jNpjdP833JCNCGQrXtVO3DeTAGs3T1tGmiEsqp6kT6Gp5zCFnh
oaQk9jfQL2S+IVnVhHVMW9nTwNPPrnIrD69FlgTrK301mcYW1mKoFotTogzHu+0=
=2IG+
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.15-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen features and fixes from David Vrabel:
"Support PCI devices with multiple MSIs, performance improvement for
kernel-based backends (by not populated m2p overrides when mapping),
and assorted minor bug fixes and cleanups"
* tag 'stable/for-linus-3.15-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/acpi-processor: fix enabling interrupts on syscore_resume
xen/grant-table: Refactor gnttab_[un]map_refs to avoid m2p_override
xen: remove XEN_PRIVILEGED_GUEST
xen: add support for MSI message groups
xen-pciback: Use pci_enable_msix_exact() instead of pci_enable_msix()
xen/xenbus: remove unused xenbus_bind_evtchn()
xen/events: remove unnecessary call to bind_evtchn_to_cpu()
xen/events: remove the unused resend_irq_on_evtchn()
drivers:xen-selfballoon:reset 'frontswap_inertia_counter' after frontswap_shrink
drivers: xen: Include appropriate header file in pcpu.c
drivers: xen: Mark function as static in platform-pci.c
Pull x86 old platform removal from Peter Anvin:
"This patchset removes support for several completely obsolete
platforms, where the maintainers either have completely vanished or
acked the removal. For some of them it is questionable if there even
exists functional specimens of the hardware"
Geert Uytterhoeven apparently thought this was a April Fool's pull request ;)
* 'x86-nuke-platforms-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, platforms: Remove NUMAQ
x86, platforms: Remove SGI Visual Workstation
x86, apic: Remove support for IBM Summit/EXA chipset
x86, apic: Remove support for ia32-based Unisys ES7000
Subsystems that want to register CPU hotplug callbacks, as well as perform
initialization for the CPUs that are already online, often do it as shown
below:
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
register_cpu_notifier(&foobar_cpu_notifier);
put_online_cpus();
This is wrong, since it is prone to ABBA deadlocks involving the
cpu_add_remove_lock and the cpu_hotplug.lock (when running concurrently
with CPU hotplug operations).
Instead, the correct and race-free way of performing the callback
registration is:
cpu_notifier_register_begin();
for_each_online_cpu(cpu)
init_cpu(cpu);
/* Note the use of the double underscored version of the API */
__register_cpu_notifier(&foobar_cpu_notifier);
cpu_notifier_register_done();
Fix the amd-bus code in x86 by using this latter form of callback
registration.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support for MSI message groups for Xen Dom0 using the
MAP_PIRQ_TYPE_MULTI_MSI pirq map type.
In order to keep track of which pirq is the first one in the group all
pirqs in the MSI group except for the first one have the newly
introduced PIRQ_MSI_GROUP flag set. This prevents calling
PHYSDEVOP_unmap_pirq on them, since the unmap must be done with the
first pirq in the group.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
The NUMAQ support seems to be unmaintained, remove it.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: David Rientjes <rientjes@google.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/n/530CFD6C.7040705@zytor.com
The SGI Visual Workstation seems to be dead; remove support so we
don't have to continue maintaining it.
Cc: Andrey Panin <pazke@donpac.ru>
Cc: Michael Reed <mdr@sgi.com>
Link: http://lkml.kernel.org/r/530CFD6C.7040705@zytor.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* pci/misc:
PCI: Enable INTx if BIOS left them disabled
ia64/PCI: Set IORESOURCE_ROM_SHADOW only for the default VGA device
x86/PCI: Set IORESOURCE_ROM_SHADOW only for the default VGA device
PCI: Update outdated comment for pcibios_bus_report_status()
PCI: Cleanup per-arch list of object files
PCI: cpqphp: Fix hex vs decimal typo in cpqhpc_probe()
x86/PCI: Fix function definition whitespace
x86/PCI: Reword comments
x86/PCI: Remove unnecessary local variable initialization
PCI: Remove unnecessary list_empty(&pci_pme_list) check
Setting the IORESOURCE_ROM_SHADOW flag on a VGA card other than the primary
prevents it from reading its own ROM. It will get the content of the
shadow ROM at C000 instead, which is of the primary VGA card and the driver
of the secondary card will bail out.
Fix this by checking if the arch code or vga-arbitration has already
determined the vga_default_device, if so only apply the fix to this primary
video device and let the comment reflect this.
[bhelgaas: add subject, split x86 & ia64 into separate patches]
Signed-off-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The PCI host bridge code doesn't care about _PXM values directly; it only
needs to know what NUMA node the hardware is on.
This uses acpi_get_node() directly and removes the _PXM stuff.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
NUMA_NO_NODE is the usual value for "we don't know what node this is on,"
e.g., it is the error return from acpi_get_node(). This changes uses of -1
to NUMA_NO_NODE. NUMA_NO_NODE is #defined to be -1 already, so this is not
a functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
list_for_each_entry() handles empty lists, so there's no need to check
whether the list is empty first.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are no callers of get_mp_bus_to_node(), so we no longer need
mp_bus_to_node[], get_mp_bus_to_node(), or set_mp_bus_to_node().
This removes them.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This replaces all uses of get_mp_bus_to_node() with x86_pci_root_bus_node().
I think these uses are all on root buses, except possibly for blind
probing, where NUMA node information is unimportant.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The AMD early_fill_mp_bus_info() already allocates a struct pci_root_info
for each PCI host bridge it finds, and that structure contains the NUMA
node number. We don't need to keep the same information in the
mp_bus_to_node[] table.
This adds x86_pci_root_bus_node(), which returns the NUMA node number, or
NUMA_NO_NODE if the node is unknown.
Note that unlike get_mp_bus_to_node(), x86_pci_root_bus_node() only works
for root buses. For example, if amd_bus.c finds a host bridge on node 1 to
[bus 00-0f], get_mp_bus_to_node() returns 1 for any bus between 00 and 0f,
but x86_pci_root_bus_node() returns 1 for bus 00 and NUMA_NO_NODE for buses
01-0f.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Nobody really uses the return value of pcibios_scan_root() (one place uses
it to control a printk, but the printk is not very useful). This converts
pcibios_scan_root() to a void function.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pci_scan_bus_on_node() is only called by pcibios_scan_root().
This merges pci_scan_bus_on_node() into pcibios_scan_root() and removes
pci_scan_bus_on_node().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pcibios_scan_root() looks up the bus's NUMA node, then calls
pci_scan_bus_on_node(). This uses pcibios_scan_root() directly and drops
the node lookup in the callers.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pci_scan_bus_with_sysdata() and pcibios_scan_root() are quite similar:
pci_scan_bus_with_sysdata
pci_scan_bus_on_node(..., &pci_root_ops, -1)
pcibios_scan_root
pci_scan_bus_on_node(..., &pci_root_ops, get_mp_bus_to_node(busnum))
get_mp_bus_to_node() returns -1 if it couldn't find the node number, so
this removes pci_scan_bus_with_sysdata() and uses pcibios_scan_root()
instead.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PCI core checks to see whether we've already scanned a bus, so we don't
need to do it in pcibios_scan_root(). Here's where it happens in the core:
pcibios_scan_root
pci_scan_bus_on_node
pci_scan_root_bus
pci_create_root_bus
b2 = pci_find_bus(pci_domain_nr(b), bus)
if (b2)
goto err_out; # already scanned this bus
This removes the check from pcibios_scan_root().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- ACPI core changes to make it create a struct acpi_device object for every
device represented in the ACPI tables during all namespace scans regardless
of the current status of that device. In accordance with this, ACPI hotplug
operations will not delete those objects, unless the underlying ACPI tables
go away.
- On top of the above, new sysfs attribute for ACPI device objects allowing
user space to check device status by triggering the execution of _STA for
its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating the
PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the code
"glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for the
DBG2 and PCCT tables to ACPICA, fixes some bugs and improves debug
facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization earlier.
That should allow us to use ACPI during the timekeeping initialization
and possibly to simplify the EFI initialization too. From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over from
Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in drivers
that uses _DSM to execute it via the new helper. From Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun Guo,
Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava, Rashika Kheria,
Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support, from
Dirk Brandewie and intel_pstate documentation from Ramkumar Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John Tobias,
Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC disabled
during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente Kurusa,
Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a cpupower
tool cleanup from One Thousand Gnomes.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=dRf6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
This code was partially based on Mark Brown's previous work.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Link: http://lkml.kernel.org/r/1387224459-25746-4-git-send-email-david.a.cohen@linux.intel.com
Signed-off-by: Fei Yang <fei.yang@intel.com>
Cc: Mark F. Brown <mark.f.brown@intel.com>
Cc: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
[ hpa: undid incorrect removal from arch/x86/kernel/head_32.S ]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Link: http://lkml.kernel.org/r/1389054026-12947-1-git-send-email-paul.gortmaker@windriver.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Change x86_msi.restore_msi_irqs(struct pci_dev *dev, int irq) to
x86_msi.restore_msi_irqs(struct pci_dev *dev).
restore_msi_irqs() restores multiple MSI-X IRQs, so param 'int irq' is
unneeded. This makes code more consistent between vm and bare metal.
Dom0 MSI-X restore code can also be optimized as XEN only has a hypercall
to restore all MSI-X vectors at one time.
Tested-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The following warnings can be seen in W=1 builds, because the original
sfi_acpi.[ch] header inclusions are incorrect:
include/linux/sfi_acpi.h:72:2: error: implicit declaration of function 'acpi_table_parse' [-Werror=implicit-function-declaration]
drivers/sfi/sfi_acpi.c:154:5: warning: no previous prototype for 'sfi_acpi_table_parse' [-Wmissing-prototypes]
Fix linux/sfi_acpi.h and modify drivers/sfi/sfi_acpi.c accordingly.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[rjw: Subject and changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify struct acpi_dev_node to contain a pointer to struct acpi_device
associated with the given device object (that is, its ACPI companion
device) instead of an ACPI handle corresponding to it. Introduce two
new macros for manipulating that pointer in a CONFIG_ACPI-safe way,
ACPI_COMPANION() and ACPI_COMPANION_SET(), and rework the
ACPI_HANDLE() macro to take the above changes into account.
Drop the ACPI_HANDLE_SET() macro entirely and rework its users to
use ACPI_COMPANION_SET() instead. For some of them who used to
pass the result of acpi_get_child() directly to ACPI_HANDLE_SET()
introduce a helper routine acpi_preset_companion() doing an
equivalent thing.
The main motivation for doing this is that there are things
represented by struct acpi_device objects that don't have valid
ACPI handles (so called fixed ACPI hardware features, such as
power and sleep buttons) and we would like to create platform
device objects for them and "glue" them to their ACPI companions
in the usual way (which currently is impossible due to the
lack of valid ACPI handles). However, there are more reasons
why it may be useful.
First, struct acpi_device pointers allow of much better type checking
than void pointers which are ACPI handles, so it should be more
difficult to write buggy code using modified struct acpi_dev_node
and the new macros. Second, the change should help to reduce (over
time) the number of places in which the result of ACPI_HANDLE() is
passed to acpi_bus_get_device() in order to obtain a pointer to the
struct acpi_device associated with the given "physical" device,
because now that pointer is returned by ACPI_COMPANION() directly.
Finally, the change should make it easier to write generic code that
will build both for CONFIG_ACPI set and unset without adding explicit
compiler directives to it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> # on Haswell
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com> # for ATA and SDIO part
* pci/misc:
PCI: Enable upstream bridges even for VFs on virtual buses
PCI: Add pci_upstream_bridge()
PCI: Add x86_msi.msi_mask_irq() and msix_mask_irq()
Certain platforms do not allow writes in the MSI-X BARs to setup or tear
down vector values. To combat against the generic code trying to write to
that and either silently being ignored or crashing due to the pagetables
being marked R/O this patch introduces a platform override.
Note that we keep two separate, non-weak, functions default_mask_msi_irqs()
and default_mask_msix_irqs() for the behavior of the arch_mask_msi_irqs()
and arch_mask_msix_irqs(), as the default behavior is needed by x86 PCI
code.
For Xen, which does not allow the guest to write to MSI-X tables - as the
hypervisor is solely responsible for setting the vector values - we
implement two nops.
This fixes a Xen guest crash when passing a PCI device with MSI-X to the
guest. See the bugzilla for more details.
[bhelgaas: add bugzilla info]
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=64581
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
CC: Zhenzhong Duan <zhenzhong.duan@oracle.com>
