During controller initialization, an LE Set RPA Timeout command is sent
to the controller if supported. However, the value checked to determine
if the command is supported is incorrect. Page 1921 of the Bluetooth
Core Spec v5.2 shows that bit 2 of octet 35 of the Supported_Commands
field corresponds to the LE Set RPA Timeout command, but currently
bit 6 of octet 35 is checked. This patch checks the correct value
instead.
This issue led to the error seen in the following btmon output during
initialization of an adapter (rtl8761b) and prevented initialization
from completing.
< HCI Command: LE Set Resolvable Private Address Timeout (0x08|0x002e) plen 2
Timeout: 900 seconds
> HCI Event: Command Complete (0x0e) plen 4
LE Set Resolvable Private Address Timeout (0x08|0x002e) ncmd 2
Status: Unsupported Remote Feature / Unsupported LMP Feature (0x1a)
= Close Index: 00:E0:4C:6B:E5:03
The error did not appear when running with this patch.
Signed-off-by: Edward Vear <edwardvear@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This renames get_adv_instance_scan_rsp to adv_instance_is_scannable and
make it return a bool since it was not actually properly return the size
of the scan response as one could expect.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Current code is actually failing on the following tests of mgmt-tester
because get_adv_instance_scan_rsp_len did not account for flags that
cause scan response data to be included resulting in non-scannable
instance when in fact it should be scannable.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This test case is meant to verify that multiple
unknown options is included in the response.
BLUETOOTH CORE SPECIFICATION Version 5.2 | Vol 3, Part A
page 1057
'On an unknown option failure (Result=0x0003),
the option(s) that contain anoption type field that is not
understood by the recipient of the L2CAP_CONFIGURATION_REQ
packet shall be included in the L2CAP_CONFIGURATION_RSP
packet unless they are hints.'
Before this patch:
> ACL Data RX: Handle 11 flags 0x02 dlen 24
L2CAP: Configure Request (0x04) ident 18 len 16
Destination CID: 64
Flags: 0x0000
Option: Unknown (0x10) [mandatory]
10 00 11 02 11 00 12 02 12 00
< ACL Data TX: Handle 11 flags 0x00 dlen 17
L2CAP: Configure Response (0x05) ident 18 len 9
Source CID: 64
Flags: 0x0000
Result: Failure - unknown options (0x0003)
Option: Unknown (0x10) [mandatory]
12
After this patch:
> ACL Data RX: Handle 11 flags 0x02 dlen 24
L2CAP: Configure Request (0x04) ident 5 len 16
Destination CID: 64
Flags: 0x0000
Option: Unknown (0x10) [mandatory]
10 00 11 02 11 00 12 02 12 00
< ACL Data TX: Handle 11 flags 0x00 dlen 23
L2CAP: Configure Response (0x05) ident 5 len 15
Source CID: 64
Flags: 0x0000
Result: Failure - unknown options (0x0003)
Option: Unknown (0x10) [mandatory]
10 11 01 11 12 01 12
Signed-off-by: Jimmy Wahlberg <jimmywa@spotify.com>
Reviewed-by: Luiz Augusto Von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
mtk_setup_firmware() misses to call release_firmware() in an error
path. Jump to free_fw to fix it.
Fixes: 737cd06072 ("Bluetooth: btmtksdio: fix up firmware download sequence")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
btusb_mtk_setup_firmware() misses to call release_firmware() in an error
path. Jump to err_release_fw to fix it.
Fixes: f645125711 ("Bluetooth: btusb: fix up firmware download sequence")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This change will allow to use different NVM file based
on WCN3991 BT SoC ID.Need to use different NVM file based on
fab location for WCN3991 BT SoC.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add OBDA0623 ACPI HID to the acpi_device_id table. This HID is used
for the RTL8723BS Bluetooth part on the Acer Switch 10E SW3-016.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1665610
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There have been multiple revisions of the patch fix the h5->rx_skb
leak. Accidentally the first revision (which is buggy) and v5 have
both been merged:
v1 commit 70f259a3f4 ("Bluetooth: hci_h5: close serdev device and free
hu in h5_close");
v5 commit 855af2d74c ("Bluetooth: hci_h5: fix memory leak in h5_close")
The correct v5 makes changes slightly higher up in the h5_close()
function, which allowed both versions to get merged without conflict.
The changes from v1 unconditionally frees the h5 data struct, this
is wrong because in the serdev enumeration case the memory is
allocated in h5_serdev_probe() like this:
h5 = devm_kzalloc(dev, sizeof(*h5), GFP_KERNEL);
So its lifetime is tied to the lifetime of the driver being bound
to the serdev and it is automatically freed when the driver gets
unbound. In the serdev case the same h5 struct is re-used over
h5_close() and h5_open() calls and thus MUST not be free-ed in
h5_close().
The serdev_device_close() added to h5_close() is incorrect in the
same way, serdev_device_close() is called on driver unbound too and
also MUST no be called from h5_close().
This reverts the changes made by merging v1 of the patch, so that
just the changes of the correct v5 remain.
Cc: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This replaces the BT_DBG function to bt_dev_dbg as it is cleaner to show
the controller index in the debug message.
Signed-off-by: Howard Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently qca_suspend() is relied on IBS mechanism. During
FW download and memory dump collections, IBS will be disabled.
In those cases, driver will allow suspend and still uses the
serdev port, which results to errors. Now added a wait timeout
if suspend is triggered during FW download and memory collections.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently the check for a failed bt_skb_alloc allocation is incorrectly
checking using IS_ERR and this can lead to a null pointer dereference. Fix
this by checking for a null pointer return using the !skb idiom.
Addresses-Coverity: ("Dereference null return")
Fixes: 1996d9cad6 ("Bluetooth: btrtl: Ask 8821C to drop old firmware")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When using the wl1271 Bluetooth function of am335x, it is found that the
Bluetooth module cannot respond in time after Bluetooth is enabled, and
a small delay is needed to work normally, so whether to add a small
mdelay.
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Replace symbolic permissions with octal values. Use usleep_range
for small msec values due to the fact that msleep() less than
20ms may have unexpected behavior/sleep longer.
- https://lkml.org/lkml/2016/8/2/1945
- Documentation/timers/timers-howto.rst
Signed-off-by: Nigel Christian <nigel.l.christian@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently driver only retries to download FW if FW downloading
is failed. Sometimes observed command timeout for version request
command, if this happen on some platforms during boot time, then
a reboot is needed to turn ON BT. Instead to avoid a reboot, now
extended retry logic for version request command too.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to the spec Ver 5.2, Vol 3, Part C, Sec 5.2.2.8:
Device in security mode 4 level 4 shall enforce:
128-bit equivalent strength for link and encryption keys required
using FIPS approved algorithms (E0 not allowed, SAFER+ not allowed,
and P-192 not allowed; encryption key not shortened)
This patch rejects connection with key size below 16 for FIPS
level services.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When h5_close() is called, h5 is directly freed when !hu->serdev.
However, h5->rx_skb is not freed, which causes a memory leak.
Freeing h5->rx_skb and setting it to NULL, fixes this memory leak.
Fixes: ce945552fd ("Bluetooth: hci_h5: Add support for serdev enumerated devices")
Reported-by: syzbot+6ce141c55b2f7aafd1c4@syzkaller.appspotmail.com
Tested-by: syzbot+6ce141c55b2f7aafd1c4@syzkaller.appspotmail.com
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A different wait queue was used when removing ctrl_wait than when adding
it. This effectively made the remove operation without locking compared
to other operations on the wait queue ctrl_wait was part of. This caused
issues like below where dead000000000100 is LIST_POISON1 and
dead000000000200 is LIST_POISON2.
list_add corruption. next->prev should be prev (ffffffc1b0a33a08), \
but was dead000000000200. (next=ffffffc03ac77de0).
------------[ cut here ]------------
CPU: 3 PID: 2138 Comm: bluetoothd Tainted: G O 4.4.238+ #9
...
---[ end trace 0adc2158f0646eac ]---
Call trace:
[<ffffffc000443f78>] __list_add+0x38/0xb0
[<ffffffc0000f0d04>] add_wait_queue+0x4c/0x68
[<ffffffc00020eecc>] __pollwait+0xec/0x100
[<ffffffc000d1556c>] bt_sock_poll+0x74/0x200
[<ffffffc000bdb8a8>] sock_poll+0x110/0x128
[<ffffffc000210378>] do_sys_poll+0x220/0x480
[<ffffffc0002106f0>] SyS_poll+0x80/0x138
[<ffffffc00008510c>] __sys_trace_return+0x0/0x4
Unable to handle kernel paging request at virtual address dead000000000100
...
CPU: 4 PID: 5387 Comm: kworker/u15:3 Tainted: G W O 4.4.238+ #9
...
Call trace:
[<ffffffc0000f079c>] __wake_up_common+0x7c/0xa8
[<ffffffc0000f0818>] __wake_up+0x50/0x70
[<ffffffc000be11b0>] sock_def_wakeup+0x58/0x60
[<ffffffc000de5e10>] l2cap_sock_teardown_cb+0x200/0x224
[<ffffffc000d3f2ac>] l2cap_chan_del+0xa4/0x298
[<ffffffc000d45ea0>] l2cap_conn_del+0x118/0x198
[<ffffffc000d45f8c>] l2cap_disconn_cfm+0x6c/0x78
[<ffffffc000d29934>] hci_event_packet+0x564/0x2e30
[<ffffffc000d19b0c>] hci_rx_work+0x10c/0x360
[<ffffffc0000c2218>] process_one_work+0x268/0x460
[<ffffffc0000c2678>] worker_thread+0x268/0x480
[<ffffffc0000c94e0>] kthread+0x118/0x128
[<ffffffc000085070>] ret_from_fork+0x10/0x20
---[ end trace 0adc2158f0646ead ]---
Signed-off-by: Ole Bjørn Midtbø <omidtbo@cisco.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Avoid multiple attempts to create the debugfs entry, force_bredr_smp,
by moving it from the SMP registration to the BR/EDR controller init
section. hci_debugfs_create_bredr is only called when HCI_SETUP and
HCI_CONFIG is not set.
Signed-off-by: Claire Chang <tientzu@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When adding device to white list the device is added to resolving list
also. It has to be added only when HCI_ENABLE_LL_PRIVACY flag is set.
HCI_ENABLE_LL_PRIVACY flag has to be tested before adding/deleting devices
to resolving list. use_ll_privacy macro is used only to check if controller
supports LL_Privacy.
https://bugzilla.kernel.org/show_bug.cgi?id=209745
Fixes: 0eee35bdfa ("Bluetooth: Update resolving list when updating whitelist")
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some platforms keep USB power even when they are powered off and in S5,
this makes Realtek 8821C keep its firmware even after a cold boot, and
make 8821C never load new firmware.
So use vendor specific HCI command to ask 8821C drop its firmware after
system shutdown.
Newer firmware doesn't have this issue so we only use this trick for old
8821C firmware version.
Suggested-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enhance the ic_id_table that it's able to maintain regularly.
To judge which chip should be initialized by LMP subversion, HCI revision,
HCI version and HCI bus which were given in the ic_id_table.
Also, refine the incorrect LMP subversion of ROM for RTL8723D and
RTL8723A.
Suggested-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When an LE connection request is made, advertising is disabled and never
resumed. When a client has an active advertisement, this is disruptive.
This change adds resume logic for client-configured (non-directed)
advertisements after the connection attempt.
The patch was tested by registering an advertisement, initiating an LE
connection from a remote peer, and verifying that the advertisement is
re-activated after the connection is established. This is performed on
Hatch and Kukui Chromebooks.
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
AMP_MGR is getting derefernced in hci_phy_link_complete_evt(), when called
from hci_event_packet() and there is a possibility, that hcon->amp_mgr may
not be found when accessing after initialization of hcon.
- net/bluetooth/hci_event.c:4945
The bug seems to get triggered in this line:
bredr_hcon = hcon->amp_mgr->l2cap_conn->hcon;
Fix it by adding a NULL check for the hcon->amp_mgr before checking the ev-status.
Fixes: d5e911928b ("Bluetooth: AMP: Process Physical Link Complete evt")
Reported-and-tested-by: syzbot+0bef568258653cff272f@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=0bef568258653cff272f
Signed-off-by: Anmol Karn <anmol.karan123@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
WCN3991 supports connectable advertisements so we need to add the valid
le states quirk so the 'central-peripheral' role is exposed in
userspace.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Set all EHL/TGL phy_addr to -1 so that the driver will automatically
detect it at run-time by probing all the possible 32 addresses.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Link: https://lore.kernel.org/r/20201106094341.4241-1-vee.khee.wong@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder says:
====================
net: ipa: constrain GSI interrupts
The goal of this series is to more tightly control when GSI
interrupts are enabled. This is a long-ish series, so I'll
describe it in parts.
The first patch is actually unrelated... I forgot to include
it in my previous series (which exposed the GSI layer to the
IPA version). It is a trivial comments-only update patch.
The second patch defers registering the GSI interrupt handler
until *after* all of the resources that handler touches have
been initialized. In practice, we don't see this interrupt
that early, but this precludes an obvious problem.
The next two patches are simple changes. The first just
trivially renames a field. The second switches from using
constant mask values to using an enumerated type of bit
positions to represent each GSI interrupt type.
The rest implement the "real work." First, all interrupts
are disabled at initialization time. Next, we keep track of
a bitmask of enabled GSI interrupt types, updating it each
time we enable or disable one of them. From there we have
a set of patches that one-by-one enable each interrupt type
only during the period it is required. This includes allowing
a channel to generate IEOB interrupts only when it has been
enabled. And finally, the last patch simplifies some code
now that all GSI interrupt types are handled uniformly.
====================
Link: https://lore.kernel.org/r/20201105181407.8006-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that all of the GSI interrupts are handled uniformly,
change gsi_irq_type_update() so it takes a value. Have the
function assign that value to the cached mask of enabled GSI
IRQ types before writing it to hardware.
Note that gsi_irq_teardown() will only be called after
gsi_irq_disable(), so it's not necessary for the former
to disable all IRQ types. Get rid of that.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most GSI general errors are unrecoverable without a full reset.
Despite that, we want to receive these errors so we can at least
report what happened before whatever undefined behavior ensues.
Explicitly disable all such interrupts in gsi_irq_setup(), then
enable those we want in gsi_irq_enable(). List the interrupt types
we are interested in (everything but breakpoint) explicitly rather
than using GSI_CNTXT_GSI_IRQ_ALL, and remove that symbol's
definition.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It is possible for other execution environments (EEs, like the modem)
to request changes to local (AP) channel or event ring state. We do
not support this feature.
In gsi_irq_setup(), explicitly zero the mask that defines which
channels are permitted to generate inter-EE channel state change
interrupts. Do the same for the event ring mask.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A GSI channel must be started in order to use it to perform a
transfer data (or command) transaction. And the only time we'll see
an IEOB interrupt is if we send a transaction to a started channel.
Therefore we do not need to have the IEOB interrupt type enabled
until at least one channel has been started. And once the last
started channel has been stopped, we can disable the IEOB interrupt
type again.
We already enable the IEOB interrupt for a particular channel only
when it is started. Extend that by having the IEOB interrupt *type*
be enabled only when at least one channel is in STARTED state.
Disallow all channels from triggering the IEOB interrupt in
gsi_irq_setup(). We only enable an channel's interrupt when
needed, so there is no longer any need to zero the channel mask
in gsi_irq_disable().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The completion of a generic EE GSI command is signaled by a global
interrupt of type GP_INT1. The only other used type for a global
interrupt is a hardware error report.
First, disallow all global interrupt types in gsi_irq_setup(). We
want to know about hardware errors, so re-enable the interrupt type
in gsi_irq_enable(), to allow hardware errors to be reported.
Disable that interrupt type again in gsi_irq_disable().
We only issue generic EE commands one at a time, and there's no
reason to keep the completion interrupt enabled when no generic
EE command is pending. We furthermore have no need to enable the
GP_INT2 or GP_INT3 interrupt types (which aren't used).
The change in gsi_irq_enable() makes GSI_CNTXT_GLOB_IRQ_ALL unused,
so get rid of it. Have gsi_generic_command() enable the GP_INT1
interrupt type (in addition to the ERROR_INT type) only while a
generic command is pending.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A GSI event ring causes an event control interrupt to fire whenever
its state changes (between NOT_ALLOCATED and ALLOCATED). No event
ring should ever change state except when we request it to.
Currently, we permit *all* events rings to generate event control
interrupts--even those that are never used. And we enable event
control interrupts essentially at all times, from setup to teardown.
Instead, only enable the event control interrupt type for the
duration of an event ring command, and when doing so, only allow
the event ring being operated upon to cause the interrupt to fire.
Disallow all event rings from issuing the event control interrupt
in gsi_irq_setup().
Because an event ring's interrupt is only enabled when needed,
there is no longer any need to zero the event channel mask in
gsi_irq_disable().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A GSI channel causes a channel control interrupt to fire whenever
its state changes (between NOT_ALLOCATED, ALLOCATED, STARTED, etc.).
We do not support inter-EE channel commands (initiated by other EEs),
so no channel should ever change state except when we request it to.
Currently, we permit *all* channels to generate channel control
interrupts--even those that are never used. And we enable channel
control interrupts essentially at all times, from setup to teardown.
Instead, disable all channel control interrupts initially in
gsi_irq_setup(), and only enable the channel control interrupt
type for the duration of a channel command. When doing so, only
allow the channel being operated upon to cause the interrupt to
fire.
Because a channel's interrupt is now enabled only when needed (one
channel at a time), there is no longer any need to zero the channel
mask in gsi_irq_disable().
Add new gsi_irq_type_enable() and gsi_irq_type_disable() as helper
functions to control whether a given GSI interrupt type is enabled.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Keep track of the set of GSI interrupt types that are currently
enabled by recording the mask value to write (or last written) to
the TYPE_IRQ_MSK register.
Create a new helper function gsi_irq_type_update() to handle
actually writing the register.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce gsi_irq_setup() and gsi_irq_teardown() to disable all
GSI interrupts when first setting up GSI hardware, and to clean
things up when we're done.
Re-enable all GSI interrupt types in gsi_irq_enable(), but do
so only after each of the type-specific interrupt masks has
been configured. Similarly, disable all interrupt types in
gsi_irq_disable()--first--before zeroing out the type-specific
masks.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Define the GSI interrupt types with an enumerated type whose values
are the bit positions representing each interrupt type. Include a
short comment describing how each interrupt type is used.
Build up the enabled interrupt mask explicitly in gsi_irq_enable(),
and get rid of the definition of GSI_CNTXT_TYPE_IRQ_MSK_ALL.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rename the "event_enable_bitmap" field of the GSI structure to be
"ieob_enabled_bitmap". An upcoming patch will cache the last value
stored for another interrupt mask and this is a more direct naming
convention to follow.
Add a few comments to explain the bitmap fields in the GSI structure.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
