Since Myri-10G boards may also run in Myrinet mode instead of Ethernet,
add a message when we detect that the link partner is not running in the
right mode.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Limit the number of recoveries from a NIC hw watchdog reset to 1 by default.
It enables detection of defective NICs immediately since these memory parity
errors are expected to happen very rarely (less than once per century*NIC).
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Fix incorrect link status even with switch turned OFF.
NetXen driver failed to accurately indicate when a link is up or down.
This was encountered during failover testing, when the first port
indicated that the link was up even when the 10G switch it was assigned
to in the Bladecenter was turned off completely.
Signed-off by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This reverts commit d52df4a35a.
This patch attempted to fix e100 for non-cache coherent memory
architectures by using the cb style code that eepro100 had and using
the EL and s bits from the RFD list. Unfortunately the hardware
doesn't work exactly like this and therefore this patch actually
breaks e100. Reverting the change brings it back to the previously
known good state for 2.6.22. The pending rewrite in progress to this
code can then be safely merged later.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With firmware 5.220.11.p5, this allows to specify the anycast addresses the
device will listen to.
The anycast address range is C0:27:C0:27:C0:XX where XX goes from 00 to 1F (or
0 to 31 in dec). The value to write on anycast_mask will specify which
addresses the device listens to. Bits in a 32 bit int are numbered from 0
(least significative bit) to 31. A specific address ending in YY will be
listened to if bit YY in the value is set to one.
Examples:
0x00000000 : do not listen to any anycast address
0xFFFFFFFF : listen to every anycast address from :00 to :1F
0x00000013 : listen to anycast addresses :00, :01 and :04
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This avoids channel mismatch between driver and firmware in case we change
channel while associated to an AP.
Signed-off-by: Luis Carlos Cobo Rus <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Make sure RQ allocation is always valid
RDMA/cma: Fix initialization of next_port
IB/mlx4: Fix zeroing of rnr_retry value in ib_modify_qp()
mlx4_core: Don't set MTT address in dMPT entries with PA set
mlx4_core: Check firmware command interface revision
IB/mthca, mlx4_core: Fix typo in comment
mlx4_core: Free catastrophic error MSI-X interrupt with correct dev_id
mlx4_core: Initialize ctx_list and ctx_lock earlier
mlx4_core: Fix CQ context layout
Kill mixed case function names from scan.c/scan.h.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace WLAN_802_11_SSID with direct 'ssid' and 'ssid_len' members
like ieee80211. In the process, remove private libertas_escape_essid
and depend on the ieee80211 implementation of escape_essid instead.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Byte-swapping length fields and then passing them to memcpy() considered
harmful.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now we finally get connectivity. For a while, before something else dies...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now it at least manages to load the firmware.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Separate wireless handlers of mshX and ethX. ethX remains as before.
For mshX, it has been disabled set/get essid, wap and set mode. Get mode always
returns "Repeater" and by now we use the Nickname to show if the mesh is active
("Mesh") or not (empty). The rest remains as before.
Signed-off-by: Luis Carlos Cobo Rus <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix some wording and blinding table command options, clarify argument list for
fwt_add and fwt_list, simplify fwt_list_route
Signed-off-by: Luis Carlos Cobo Rus <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix WPA so it works up through the supplicant 4-Way handshake process.
Doesn't successfully pass traffic yet; may be problems installing
the GTK to the firmware.
- RSN needs to be enabled before the association command is sent
- Use keys from the association request not the adapter structure
- cmd_act_mac_strict_protection_enable != IW_AUTH_DROP_UNENCRYPTED
- Fix network filtering logic in is_network_compatible() WPA helpers
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Any time the driver gets new scan results, even from partial scans,
it should send the scan event to userspace.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously if a fixed channel was specified along with an SSID,
the channel request would be ignored during the association
process. Instead, when searching for an adhoc or infrastructure
network to join, allow filtering results based on channel so
that the driver doesn't pick a BSS on a different channel than
requested.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inadvertently removed on a previous commit; causes the first
adhoc start to fail if a channel has not been set or no
other association has been made.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update signal quality before the locked scan result translation loop,
because calling libertas_prepare_and_send_command() with the
'waitforrsp' option grabs adapter->lock in the command return processing,
leading to the deadlock.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure the leave debug print gets triggered when necessary.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
adapter->lock should released after unlocking adapter->driver_lock to
balance the order in which they were locked at the top of the function.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BSS to associate with (in either Infrastructure or IBSS join
operations) is now stored in _one_ place in the association request (the
bss member), not two places as before (pattemptedbss and
curbssparams->bssdescriptor).
Association requests are passed to the necessary association functions
to (a) give them access to the bss member and (b) ensure that
association/join/start setup uses settings from the request, not the
current adapter settings (which may not be valid for the requested
settings).
Because the 'bss' member of the association request is used now, the
command return functions from associate and adhoc join/start need access
to the in-progress association request to update curbssparams when
everything is done. The association worker moves the request from
pending to in-progress for the duration of the association attempt.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle channel changes through the deferred association framework
rather than directly. Fixes errors when setting channels along
with other parameters like mode and SSID.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use list_for_each_entry_safe, to protect against list_del().
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis Carlos Cobo Rus <luisca@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not clear the scan list except under specific conditions, such as
when (a) user-requested, or (b) joining/starting an adhoc network.
Furthermore, only clear entries which match the SSID or BSSID of the
request, not the whole scan list.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- use a linked list for scan results
- age scan results
- pass bss_descriptors around instead of indexes into the scan table
- lock access to the scan results
- stop returning EAGAIN from SIOCGIWSCAN handler
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Updated commands fwt_add and fwt_list, bt_list.
New commands: bt_get_invert, bt_set_invert, to invert the blinding table,
i.e., receive only frames from nodes listed in the BT.
This patch needs/is needed for firmware 5.220.9.p11.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch along with the previous commands update one, is necessary for
mesh and fwt ioctls to work properly with firmware version 5.220.10.p0
and later.
Signed-off-by: Luis Carlos Cobo Rus <luiscarlos@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
libertas_activate_card() doesn't create the netdev, and shouldn't
free it on error. The caller of libertas_activate_card() is
responsible for cleaning up errors from libertas_add_card(),
not libertas_activate_card().
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
