commit 4f2bdb3c5e upstream.
When moving a station out of a VLAN and deleting the VLAN afterwards, the
fast_rx entry still holds a pointer to the VLAN's netdev, which can cause
use-after-free bugs. Fix this by immediately calling ieee80211_check_fast_rx
after the VLAN change.
Cc: stable@vger.kernel.org
Reported-by: ranygh@riseup.net
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://msgid.link/20240316074336.40442-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 413dafc817 ]
When a station has not been uploaded yet, receiving SMPS or channel width
notification action frames can lead to rate_control_rate_update calling
drv_sta_rc_update with uninitialized driver private data.
Fix this by adding a missing check for sta->uploaded.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://msgid.link/20240221140535.16102-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcbc84af11 ]
fast-xmit must only be enabled after the sta has been uploaded to the driver,
otherwise it could end up passing the not-yet-uploaded sta via drv_tx calls
to the driver, leading to potential crashes because of uninitialized drv_priv
data.
Add a missing sta->uploaded check and re-check fast xmit after inserting a sta.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://msgid.link/20240104181059.84032-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c98d8836b8 upstream.
This pointer can change here since the SKB can change, so we
actually later open-coded IEEE80211_SKB_CB() again. Reload
the pointer where needed, so the monitor-mode case using it
gets fixed, and then use info-> later as well.
Cc: stable@vger.kernel.org
Fixes: 5316821590 ("mac80211: fix VLAN handling with TXQs")
Link: https://msgid.link/20240131164910.b54c28d583bc.I29450cec84ea6773cff5d9c16ff92b836c331471@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b01a74b3ca ]
When a station is allocated, links are added but not
set to valid yet (e.g. during connection to an AP MLD),
we might remove the station without ever marking links
valid, and leak them. Fix that.
Fixes: cb71f1d136 ("wifi: mac80211: add sta link addition/removal")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.6573998beaf8.I09ac2e1d41c80f82a5a616b8bd1d9d8dd709a6a6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00f7d153f3 ]
The new 320 MHz channel width wasn't handled, so connecting
a station to a 320 MHz AP would limit the station to 20 MHz
(on HT) after a warning, handle 320 MHz to fix that.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20231109182201.495381-1-greearb@candelatech.com
[write a proper commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e160ab8516 ]
We can get a UBSAN warning if ieee80211_get_tx_power() returns the
INT_MIN value mac80211 internally uses for "unset power level".
UBSAN: signed-integer-overflow in net/wireless/nl80211.c:3816:5
-2147483648 * 100 cannot be represented in type 'int'
CPU: 0 PID: 20433 Comm: insmod Tainted: G WC OE
Call Trace:
dump_stack+0x74/0x92
ubsan_epilogue+0x9/0x50
handle_overflow+0x8d/0xd0
__ubsan_handle_mul_overflow+0xe/0x10
nl80211_send_iface+0x688/0x6b0 [cfg80211]
[...]
cfg80211_register_wdev+0x78/0xb0 [cfg80211]
cfg80211_netdev_notifier_call+0x200/0x620 [cfg80211]
[...]
ieee80211_if_add+0x60e/0x8f0 [mac80211]
ieee80211_register_hw+0xda5/0x1170 [mac80211]
In this case, simply return an error instead, to indicate
that no data is available.
Cc: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20230203023636.4418-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 428e8976a1 ]
During my refactoring I wanted to get rid of the switch,
but replaced it with the wrong calculation. Fix that.
Fixes: 175ad2ec89 ("wifi: mac80211: limit A-MSDU subframes for client too")
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230827135854.51bf1b8b0adb.Iffbd337fdad2b86ae12f5a39c69fb82b517f7486@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eadfb54756 ]
This also has the wiphy locked here then. We need to use
the _locked version of cfg80211_sched_scan_stopped() now,
which also fixes an old deadlock there.
Fixes: a05829a722 ("cfg80211: avoid holding the RTNL when calling the driver")
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97c19e42b2 ]
Make the offchannel works wiphy works to have the
wiphy locked for executing them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stable-dep-of: eadfb54756 ("wifi: mac80211: move sched-scan stop work to wiphy work")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 201712512c ]
Move the scan work to wiphy work, which also simplifies
the way we handle the work vs. the scan configuration.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stable-dep-of: eadfb54756 ("wifi: mac80211: move sched-scan stop work to wiphy work")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 228e4f931b ]
Move the radar detect work to wiphy work in order
to lock the wiphy for it without doing it manually.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stable-dep-of: eadfb54756 ("wifi: mac80211: move sched-scan stop work to wiphy work")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61304336c6 ]
Lower layer device driver stop/wake TX by calling ieee80211_stop_queue()/
ieee80211_wake_queue() while hw scan. Sometimes hw scan and PTK rekey are
running in parallel, when M4 sent from wpa_supplicant arrive while the TX
queue is stopped, then the M4 will pending send, and then new key install
from wpa_supplicant. After TX queue wake up by lower layer device driver,
the M4 will be dropped by below call stack.
When key install started, the current key flag is set KEY_FLAG_TAINTED in
ieee80211_pairwise_rekey(), and then mac80211 wait key install complete by
lower layer device driver. Meanwhile ieee80211_tx_h_select_key() will return
TX_DROP for the M4 in step 12 below, and then ieee80211_free_txskb() called
by ieee80211_tx_dequeue(), so the M4 will not send and free, then the rekey
process failed becaue AP not receive M4. Please see details in steps below.
There are a interval between KEY_FLAG_TAINTED set for current key flag and
install key complete by lower layer device driver, the KEY_FLAG_TAINTED is
set in this interval, all packet including M4 will be dropped in this
interval, the interval is step 8~13 as below.
issue steps:
TX thread install key thread
1. stop_queue -idle-
2. sending M4 -idle-
3. M4 pending -idle-
4. -idle- starting install key from wpa_supplicant
5. -idle- =>ieee80211_key_replace()
6. -idle- =>ieee80211_pairwise_rekey() and set
currently key->flags |= KEY_FLAG_TAINTED
7. -idle- =>ieee80211_key_enable_hw_accel()
8. -idle- =>drv_set_key() and waiting key install
complete from lower layer device driver
9. wake_queue -waiting state-
10. re-sending M4 -waiting state-
11. =>ieee80211_tx_h_select_key() -waiting state-
12. drop M4 by KEY_FLAG_TAINTED -waiting state-
13. -idle- install key complete with success/fail
success: clear flag KEY_FLAG_TAINTED
fail: start disconnect
Hence add check in step 11 above to allow the EAPOL send out in the
interval. If lower layer device driver use the old key/cipher to encrypt
the M4, then AP received/decrypt M4 correctly, after M4 send out, lower
layer device driver install the new key/cipher to hardware and return
success.
If lower layer device driver use new key/cipher to send the M4, then AP
will/should drop the M4, then it is same result with this issue, AP will/
should kick out station as well as this issue.
issue log:
kworker/u16:4-5238 [000] 6456.108926: stop_queue: phy1 queue:0, reason:0
wpa_supplicant-961 [003] 6456.119737: rdev_tx_control_port: wiphy_name=phy1 name=wlan0 ifindex=6 dest=ARRAY[9e, 05, 31, 20, 9b, d0] proto=36488 unencrypted=0
wpa_supplicant-961 [003] 6456.119839: rdev_return_int_cookie: phy1, returned 0, cookie: 504
wpa_supplicant-961 [003] 6456.120287: rdev_add_key: phy1, netdev:wlan0(6), key_index: 0, mode: 0, pairwise: true, mac addr: 9e:05:31:20:9b:d0
wpa_supplicant-961 [003] 6456.120453: drv_set_key: phy1 vif:wlan0(2) sta:9e:05:31:20:9b:d0 cipher:0xfac04, flags=0x9, keyidx=0, hw_key_idx=0
kworker/u16:9-3829 [001] 6456.168240: wake_queue: phy1 queue:0, reason:0
kworker/u16:9-3829 [001] 6456.168255: drv_wake_tx_queue: phy1 vif:wlan0(2) sta:9e:05:31:20:9b:d0 ac:0 tid:7
kworker/u16:9-3829 [001] 6456.168305: cfg80211_control_port_tx_status: wdev(1), cookie: 504, ack: false
wpa_supplicant-961 [003] 6459.167982: drv_return_int: phy1 - -110
issue call stack:
nl80211_frame_tx_status+0x230/0x340 [cfg80211]
cfg80211_control_port_tx_status+0x1c/0x28 [cfg80211]
ieee80211_report_used_skb+0x374/0x3e8 [mac80211]
ieee80211_free_txskb+0x24/0x40 [mac80211]
ieee80211_tx_dequeue+0x644/0x954 [mac80211]
ath10k_mac_tx_push_txq+0xac/0x238 [ath10k_core]
ath10k_mac_op_wake_tx_queue+0xac/0xe0 [ath10k_core]
drv_wake_tx_queue+0x80/0x168 [mac80211]
__ieee80211_wake_txqs+0xe8/0x1c8 [mac80211]
_ieee80211_wake_txqs+0xb4/0x120 [mac80211]
ieee80211_wake_txqs+0x48/0x80 [mac80211]
tasklet_action_common+0xa8/0x254
tasklet_action+0x2c/0x38
__do_softirq+0xdc/0x384
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Link: https://lore.kernel.org/r/20230801064751.25803-1-quic_wgong@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 084cf2aeca ]
Cisco AP module 9115 with FW 17.3 has a bug and sends a too
large maximum MPDU length in the association response
(indicating 12k) that it cannot actually process.
Work around that by taking the minimum between what's in the
association response and the BSS elements (from beacon or
probe response).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230918140607.d1966a9a532e.I090225babb7cd4d1081ee9acd40e7de7e41c15ae@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31db78a492 ]
When ieee80211_key_link() is called by ieee80211_gtk_rekey_add()
but returns 0 due to KRACK protection (identical key reinstall),
ieee80211_gtk_rekey_add() will still return a pointer into the
key, in a potential use-after-free. This normally doesn't happen
since it's only called by iwlwifi in case of WoWLAN rekey offload
which has its own KRACK protection, but still better to fix, do
that by returning an error code and converting that to success on
the cfg80211 boundary only, leaving the error for bad callers of
ieee80211_gtk_rekey_add().
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: fdf7cb4185 ("mac80211: accept key reinstall without changing anything")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67dfa589aa ]
When probing a client, first check if we have it, and then
check for the channel context, otherwise you can trigger
the warning there easily by probing when the AP isn't even
started yet. Since a client existing means the AP is also
operating, we can then keep the warning.
Also simplify the moved code a bit.
Reported-by: syzbot+999fac712d84878a7379@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19e4a47ee7 ]
Before checking the action code, check that it even
exists in the frame.
Reported-by: syzbot+be9c824e6f269d608288@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b98c16107c upstream.
The commit 06470f7468 ("mac80211: add API to allow filtering frames in BA sessions")
added reorder_buf_filtered to mark frames filtered by firmware, and it
can only work correctly if hw.max_rx_aggregation_subframes <= 64 since
it stores the bitmap in a u64 variable.
However, new HE or EHT devices can support BlockAck number up to 256 or
1024, and then using a higher subframe index leads UBSAN warning:
UBSAN: shift-out-of-bounds in net/mac80211/rx.c:1129:39
shift exponent 215 is too large for 64-bit type 'long long unsigned int'
Call Trace:
<IRQ>
dump_stack_lvl+0x48/0x70
dump_stack+0x10/0x20
__ubsan_handle_shift_out_of_bounds+0x1ac/0x360
ieee80211_release_reorder_frame.constprop.0.cold+0x64/0x69 [mac80211]
ieee80211_sta_reorder_release+0x9c/0x400 [mac80211]
ieee80211_prepare_and_rx_handle+0x1234/0x1420 [mac80211]
ieee80211_rx_list+0xaef/0xf60 [mac80211]
ieee80211_rx_napi+0x53/0xd0 [mac80211]
Since only old hardware that supports <=64 BlockAck uses
ieee80211_mark_rx_ba_filtered_frames(), limit the use as it is, so add a
WARN_ONCE() and comment to note to avoid using this function if hardware
capability is not suitable.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20230818014004.16177-1-pkshih@realtek.com
[edit commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6e21e7b8cd ]
In mesh mode, ieee80211_chandef_he_6ghz_oper() is called by
mesh_matches_local() for every received mesh beacon.
On a 6 GHz mesh of a HE-only phy, this spams that the hardware does not
have EHT capabilities, even if the received mesh beacon does not have an
EHT element.
Unlike HE, not supporting EHT in the 6 GHz band is not an error so do
not print anything in this case.
Fixes: 5dca295dd7 ("mac80211: Add initial support for EHT and 320 MHz channels")
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230614132648.28995-1-nicolas.cavallari@green-communications.fr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4cacadc0db ]
The entry should be a read only one and not a write only one. Fix it.
Fixes: 3d90110292 ("wifi: mac80211: implement link switching")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230611121219.c75316990411.I1565a7fcba8a37f83efffb0cc6b71c572b896e94@changeid
[remove x16 change since it doesn't work yet]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba7af2654e ]
When adding a new link to a station, this needs to cause a
recalculation of the minimum chandef since otherwise we can
have a higher bandwidth station connected on that link than
the link is operating at. Do the appropriate recalc.
Fixes: cb71f1d136 ("wifi: mac80211: add sta link addition/removal")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230604120651.377adf3c789a.I91bf28f399e16e6ac1f83bacd1029a698b4e6685@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15846f95ab ]
ieee80211_vif_set_links requires the sdata->local->mtx lock to be held.
Add the appropriate locking around the calls in both the link add and
remove handlers.
This causes a warning when e.g. ieee80211_link_release_channel is called
via ieee80211_link_stop from ieee80211_vif_update_links.
Fixes: 0d8c4a3c86 ("wifi: mac80211: implement add/del interface link callbacks")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230608163202.fa0c6597fdad.I83dd70359f6cda30f86df8418d929c2064cf4995@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01605ad6c3 ]
In the normal MLME code we always call
ieee80211_mgd_set_link_qos_params() before
ieee80211_link_info_change_notify() and some drivers,
notably iwlwifi, rely on that as they don't do anything
(but store the data) in their conf_tx.
Fix the order here to be the same as in the normal code
paths, so this isn't broken.
Fixes: 3d90110292 ("wifi: mac80211: implement link switching")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230608163202.a2a86bba2f80.Iac97e04827966d22161e63bb6e201b4061e9651b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47c171a426 ]
Don't do link address translation for beacons and probe responses,
this leads to reporting multiple scan list entries for the same AP
(one with the MLD address) which just breaks things.
We might need to extend this in the future for some other (action)
frames that aren't MLD addressed.
Fixes: 42fb9148c0 ("wifi: mac80211: do link->MLD address translation on RX")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230604120651.62adead1b43a.Ifc25eed26ebf3b269f60b1ec10060156d0e7ec0d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68c228557d ]
There were two bugs when creating the non-inheritence
element:
1) 'at_extension' needs to be declared outside the loop,
otherwise the value resets every iteration and we
can never really switch properly
2) 'added' never got set to true, so we always cut off
the extension element again at the end of the function
This shows another issue that we might add a list but no
extension list, but we need to make the extension list a
zero-length one in that case.
Fix all these issues. While at it, add a comment explaining
the trim.
Fixes: 81151ce462 ("wifi: mac80211: support MLO authentication/association with one link")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230604120651.3addaa5c4782.If3a78f9305997ad7ef4ba7ffc17a8234c956f613@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c37ab22bb1 ]
We already check that the right iftype capa exists,
but then don't use it. Assign it to a variable so we
can actually use it, and then do that.
Fixes: bac2fd3d75 ("mac80211: remove use of ieee80211_get_he_sta_cap()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230604120651.0e908e5c5fdd.Iac142549a6144ac949ebd116b921a59ae5282735@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04312de4ce ]
When we allocate a new channel context, or find an existing one
that is compatible, we currently assign it to a link before its
mindef is updated. This leads to strange situations, especially
in link switching where you switch to an 80 MHz link and expect
it to be active immediately, but the mindef is still configured
to 20 MHz while assigning. Also, it's strange that the chandef
passed to the assign method's argument is wider than the one in
the context.
Fix this by calculating the mindef with the new link considered
before calling the driver.
In particular, this fixes an iwlwifi problem during link switch
where the firmware would assert because the (link) station that
was added for the AP is configured to transmit at a bandwidth
that's wider than the channel context that it's configured on.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230504134511.828474-5-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b72a455a24 ]
When a chanctx is reserved for a new vif and we recalculate
the minimal definition for it, we need to consider the new
interface it's being reserved for before we assign it, so it
can be used directly with the correct min channel width.
Fix the code to - optionally - consider that, and use that
option just before doing the reassignment.
Also, when considering channel context reservations, we
should only consider the one link we're currently working with.
Change the boolean argument to a link pointer to do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230504134511.828474-4-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 860e1b43da ]
There's no need to call ieee80211_recalc_chanctx_min_def()
since it cannot and won't call the driver anyway; just use
_ieee80211_recalc_chanctx_min_def() instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230504134511.828474-3-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a23d7f5b2f ]
When stopping the AP, there might be a color change in progress. It
should be deactivated here, or the driver might later finalize a color
change on a stopped AP.
Fixes: 5f9404abdf (mac80211: add support for BSS color change)
Signed-off-by: Michael Lee <michael-cy.lee@mediatek.com>
Link: https://lore.kernel.org/r/20230504080441.22958-1-michael-cy.lee@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 248e477651 ]
We need to set the correct trace variable, otherwise we're
overwriting something else instead and the right one that
we print later is not initialized.
Fixes: b6011960f3 ("mac80211: handle channel frequency offset")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230504134511.828474-2-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4e348c6c6e upstream.
When ieee80211_select_queue is called for mesh, the sta pointer is usually
NULL, since the nexthop is looked up much later in the tx path.
Explicitly check for unicast address in that case in order to make qos work
again.
Cc: stable@vger.kernel.org
Fixes: 50e2ab3929 ("wifi: mac80211: fix queue selection for mesh/OCB interfaces")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230314095956.62085-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0d846bdc11 ]
There's at least one case in ieee80211_rx_for_interface()
where we might pass &((struct sta_info *)NULL)->sta to it
only to then do container_of(), and then checking the
result for NULL, but checking the result of container_of()
for NULL looks really odd.
Fix this by just passing the struct sta_info * instead.
Fixes: e66b7920aa ("wifi: mac80211: fix initialization of rx->link and rx->link_sta")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf08e29db7 ]
The convention for find_first_bit() is 0-based, while ffs()
is 1-based, so this is now off-by-one. I cannot reproduce the
gcc-9 problem, but since the -1 is now removed, I'm hoping it
will still avoid the original issue.
Reported-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Fixes: 1d8d4af434 ("wifi: mac80211: avoid u32_encode_bits() warning")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d8d4af434 ]
gcc-9 triggers a false-postive warning in ieee80211_mlo_multicast_tx()
for u32_encode_bits(ffs(links) - 1, ...), since ffs() can return zero
on an empty bitmask, and the negative argument to u32_encode_bits()
is then out of range:
In file included from include/linux/ieee80211.h:21,
from include/net/cfg80211.h:23,
from net/mac80211/tx.c:23:
In function 'u32_encode_bits',
inlined from 'ieee80211_mlo_multicast_tx' at net/mac80211/tx.c:4437:17,
inlined from 'ieee80211_subif_start_xmit' at net/mac80211/tx.c:4485:3:
include/linux/bitfield.h:177:3: error: call to '__field_overflow' declared with attribute error: value doesn't fit into mask
177 | __field_overflow(); \
| ^~~~~~~~~~~~~~~~~~
include/linux/bitfield.h:197:2: note: in expansion of macro '____MAKE_OP'
197 | ____MAKE_OP(u##size,u##size,,)
| ^~~~~~~~~~~
include/linux/bitfield.h:200:1: note: in expansion of macro '__MAKE_OP'
200 | __MAKE_OP(32)
| ^~~~~~~~~
Newer compiler versions do not cause problems with the zero argument
because they do not consider this a __builtin_constant_p().
It's also harmless since the hweight16() check already guarantees
that this cannot be 0.
Replace the ffs() with an equivalent find_first_bit() check that
matches the later for_each_set_bit() style and avoids the warning.
Fixes: 963d0e8d08 ("wifi: mac80211: optionally implement MLO multicast TX")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230214132025.1532147-1-arnd@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit daf8fb4295 ]
MLD address translation should be done only for individually addressed
frames. Otherwise, AAD calculation would be wrong and the decryption
would fail.
Fixes: e66b7920aa ("wifi: mac80211: fix initialization of rx->link and rx->link_sta")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Link: https://lore.kernel.org/r/20230214101048.792414-1-andrei.otcheretianski@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aaacf1740f ]
Non-MLO station frames are dropped in Rx path due to the condition
check in ieee80211_rx_is_valid_sta_link_id(). In multi-link AP scenario,
non-MLO stations try to connect in any of the valid links in the ML AP,
where the station valid_links and link_id params are valid in the
ieee80211_sta object. But ieee80211_rx_is_valid_sta_link_id() always
return false for the non-MLO stations by the assumption taken is
valid_links and link_id are not valid in non-MLO stations object
(ieee80211_sta), this assumption is wrong. Due to this assumption,
non-MLO station frames are dropped which leads to failure in association.
Fix it by removing the condition check and allow the link validation
check for the non-MLO stations.
Fixes: e66b7920aa ("wifi: mac80211: fix initialization of rx->link and rx->link_sta")
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://lore.kernel.org/r/20230206160330.1613-1-quic_periyasa@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59336e07b2 ]
The value of last_rate in ieee80211_sta_rx_stats is degraded from u32 to
u16 after being assigned to rate variable, which causes information loss
in STA_STATS_FIELD_TYPE and later bitfields.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://lore.kernel.org/r/20230209110659.25447-1-shayne.chen@mediatek.com
Fixes: 41cbb0f5a2 ("mac80211: add support for HE")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9288188438 ]
Move color collision report in a dedicated delayed work and do not run
it in interrupt context in order to rate-limit the number of events
reported to userspace. Moreover grab wdev mutex in
ieee80211_color_collision_detection_work routine since it is required
by cfg80211_obss_color_collision_notify().
Tested-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Fixes: 5f9404abdf ("mac80211: add support for BSS color change")
Link: https://lore.kernel.org/r/3f6cf60c892ad40c1cca4a55d62b1224ef1c6ce9.1674644379.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa22b51ace ]
When multiple interfaces are present in the local interface
list, new skb copy is taken before rx processing except for
the first interface. The address translation happens each
time only on the original skb since the hdr pointer is not
updated properly to the newly created skb.
As a result frames start to drop in userspace when address
based checks or search fails.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/20221208040050.25922-1-quic_srirrama@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
