After sending a TDLS discovery-request, we expect a reply to arrive on
the AP's channel. We must stay on the channel (no PSM, scan, etc.), since
a TDLS setup-response is a direct packet not buffered by the AP.
Add a new mac80211 driver callback to allow discovery session protection.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make sure userspace added a TDLS peer station before invoking the
transmission of the first setup frame. This ensures packets to the peer
won't go through the AP path.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Write a mac80211 to the cfg80211 API for requesting a userspace TDLS
operation. Define TDLS specific reason codes that can be used here.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the spec mandates, flush data in the AP path before transmitting the
first setup frame. Data packets transmitted during setup are already
dropped in the Tx path.
For the teardown flow, flush all packets in the direct path before
transmitting the teardown frame. Un-authorize the peer sta after teardown
is sent, forcing all subsequent Tx to the peer through the AP.
Make sure to flush the queues when disabling the link to get the
teardown packet out.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
[adjust to Luca's new quuee API and stop only vif queues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are setup/teardown specific actions to be done that accompany
the sending of a TDLS management packet. Split the main function to
simplify future additions.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TDLS initiator is set once during link setup. If determines the
address ordering in the link identifier IE.
Use the value from userspace in order to have a correct teardown packet.
With the current code, a teardown from the responder side fails the TDLS
MIC check because of a bad link identifier IE.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TDLS initiator is set once during link setup. If determines the
address ordering in the link identifier IE.
Fix dependent drivers - mwifiex and mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When setting up a TDLS session, register a delayed work to remove
the peer if setup times out. Prevent concurrent setups to support this
capacity.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For TDLS, the AUTHORIZED flag arrives with all other important station
info (supported rates, HT/VHT caps, ...). Make sure to set the station
state in the low-level driver after transferring this information to
the mac80211 STA entry.
This aligns the STA information during sta_state callbacks with the
non-TDLS case.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rename the flags used in the Tx path and add an explanation for the
reasons to drop, send directly or through the AP.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of stopping all the hardware queues during channel switch,
which is especially bad when we have large CSA counts, stop only the
queues that are assigned to the vif that is performing the channel
switch.
Additionally, check for (sdata->csa_block_tx) instead of calling
ieee80211_csa_needs_block_tx(), which can now be removed.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases we may want to stop the queues of a single vif (for
instance during a channel-switch). Add a function that stops all the
queues that are assigned to a vif. If a queue is assigned to more
than one vif, the corresponding netdev subqueue of the other vif(s)
will also be stopped. If the HW doesn't set the
IEEE80211_HW_QUEUE_CONTROL flag, then all queues are stopped.
Also add a corresponding function to wake the queues of a vif back.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes different vifs may be stopping the queues for the same
reason (e.g. when several interfaces are performing a channel switch).
Instead of using a bitmask for the reasons, use an integer that holds
a refcount instead. In order to keep it backwards compatible,
introduce a boolean in some functions that tell us whether the queue
stopping should be refcounted or not. For now, use not refcounted for
all calls to keep it functionally the same as before.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no need to stop all queues when we want to flush specific
queues, so stop only the queues that will be flushed.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Converting time from one format to another seems to give coders a warm
and fuzzy feeling.
Use the proper interfaces.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John W. Linville <linville@tuxdriver.com>
[fix compile error]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
do_posix_clock_monotonic_gettime() is a leftover from the initial
posix timer implementation which maps to ktime_get_ts().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
vif->csa_active is protected by mutexes only. This
means it is unreliable to depend on it on codeflow
in non-sleepable beacon and CSA code. There was no
guarantee to have vif->csa_active update be
visible before beacons are updated on SMP systems.
Using csa counter offsets which are embedded in
beacon struct (and thus are protected with single
RCU assignment) is much safer.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Having csa counters part of beacon and probe_resp
structures makes it easier to get rid of possible
races between setting a beacon and updating
counters on SMP systems by guaranteeing counters
are always consistent against given beacon struct.
While at it relax WARN_ON into WARN_ON_ONCE to
prevent spamming logs and racing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[remove pointless array check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow send frames using monitor interface
when DFS chandef and we pass CAC (beaconing
allowed).
This fix problem when old kernel and new backports used,
in such case hostapd create/use also monitor interface.
Before this patch all frames hostapd send using monitor
iface were dropped when AP was configured on DFS channel.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, cfg80211 tries to implement ethtool, but that doesn't
really scale well, with all the different operations. Make the
lower-level driver responsible for it, which currently only has
an effect on mac80211. It will similarly not scale well at that
level though, since mac80211 also has many drivers.
To cleanly implement this in mac80211, introduce a new file and
move some code to appropriate places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh_plink code is doing some interesting things with the
ignore_plink_timer flag. It seems the original intent was to
handle this race:
cpu 0 cpu 1
----- -----
start timer handler for state X
acquire sta_lock
change state from X to Y
mod_timer() / del_timer()
release sta_lock
acquire sta_lock
execute state Y timer too soon
However, using the mod_timer()/del_timer() return values to
detect these cases is broken. As a result, timers get ignored
unnecessarily, and stations can get stuck in the peering state
machine.
Instead, we can detect the case by looking at the timer expiration.
In the case of del_timer, just ignore the timers in the following
(LISTEN/ESTAB) states since they won't have timers anyway.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is currently possible to have a race due to the station PS
unblock work like this:
* station goes to sleep with frames buffered in the driver
* driver blocks wakeup
* station wakes up again
* driver flushes/returns frames, and unblocks, which schedules
the unblock work
* unblock work starts to run, and checks that the station is
awake (i.e. that the WLAN_STA_PS_STA flag isn't set)
* we process a received frame with PM=1, setting the flag again
* ieee80211_sta_ps_deliver_wakeup() runs, delivering all frames
to the driver, and then clearing the WLAN_STA_PS_DRIVER and
WLAN_STA_PS_STA flags
In this scenario, mac80211 will think that the station is awake,
while it really is asleep, and any TX'ed frames should be filtered
by the device (it will know that the station is sleeping) but then
passed to mac80211 again, which will not buffer it either as it
thinks the station is awake, and eventually the packets will be
dropped.
Fix this by moving the clearing of the flags to exactly where we
learn about the situation. This creates a problem of reordering,
so introduce another flag indicating that delivery is being done,
this new flag also queues frames and is cleared only while the
spinlock is held (which the queuing code also holds) so that any
concurrent delivery/TX is handled correctly.
Reported-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Minstrel has long since proven its worth.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we need an MITM protected connection but the local and remote IO
capabilities cannot provide it we should reject the pairing attempt in
the appropriate way. This patch adds the missing checks for such a
situation to the smp_cmd_pairing_req() and smp_cmd_pairing_rsp()
functions.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll need to do authentication method lookups from more than one place,
so refactor the lookup into its own function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we receive a pairing request or an internal request to start
pairing we shouldn't blindly overwrite the existing pending_sec_level
value as that may actually be higher than the new one. This patch fixes
the SMP code to only overwrite the value in case the new one is higher
than the old.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull networking fixes from David Miller:
1) Fix checksumming regressions, from Tom Herbert.
2) Undo unintentional permissions changes for SCTP rto_alpha and
rto_beta sysfs knobs, from Denial Borkmann.
3) VXLAN, like other IP tunnels, should advertize it's encapsulation
size using dev->needed_headroom instead of dev->hard_header_len.
From Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: sctp: fix permissions for rto_alpha and rto_beta knobs
vxlan: Checksum fixes
net: add skb_pop_rcv_encapsulation
udp: call __skb_checksum_complete when doing full checksum
net: Fix save software checksum complete
net: Fix GSO constants to match NETIF flags
udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
vxlan: use dev->needed_headroom instead of dev->hard_header_len
MAINTAINERS: update cxgb4 maintainer
Commit 3fd091e73b ("[SCTP]: Remove multiple levels of msecs
to jiffies conversions.") has silently changed permissions for
rto_alpha and rto_beta knobs from 0644 to 0444. The purpose of
this was to discourage users from tweaking rto_alpha and
rto_beta knobs in production environments since they are key
to correctly compute rtt/srtt.
RFC4960 under section 6.3.1. RTO Calculation says regarding
rto_alpha and rto_beta under rule C3 and C4:
[...]
C3) When a new RTT measurement R' is made, set
RTTVAR <- (1 - RTO.Beta) * RTTVAR + RTO.Beta * |SRTT - R'|
and
SRTT <- (1 - RTO.Alpha) * SRTT + RTO.Alpha * R'
Note: The value of SRTT used in the update to RTTVAR
is its value before updating SRTT itself using the
second assignment. After the computation, update
RTO <- SRTT + 4 * RTTVAR.
C4) When data is in flight and when allowed by rule C5
below, a new RTT measurement MUST be made each round
trip. Furthermore, new RTT measurements SHOULD be
made no more than once per round trip for a given
destination transport address. There are two reasons
for this recommendation: First, it appears that
measuring more frequently often does not in practice
yield any significant benefit [ALLMAN99]; second,
if measurements are made more often, then the values
of RTO.Alpha and RTO.Beta in rule C3 above should be
adjusted so that SRTT and RTTVAR still adjust to
changes at roughly the same rate (in terms of how many
round trips it takes them to reflect new values) as
they would if making only one measurement per
round-trip and using RTO.Alpha and RTO.Beta as given
in rule C3. However, the exact nature of these
adjustments remains a research issue.
[...]
While it is discouraged to adjust rto_alpha and rto_beta
and not further specified how to adjust them, the RFC also
doesn't explicitly forbid it, but rather gives a RECOMMENDED
default value (rto_alpha=3, rto_beta=2). We have a couple
of users relying on the old permissions before they got
changed. That said, if someone really has the urge to adjust
them, we could allow it with a warning in the log.
Fixes: 3fd091e73b ("[SCTP]: Remove multiple levels of msecs to jiffies conversions.")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert reported issues regarding checksum complete and UDP.
The logic introduced in commit 7e3cead517
("net: Save software checksum complete") is not correct.
This patch:
1) Restores code in __skb_checksum_complete_header except for setting
CHECKSUM_UNNECESSARY. This function may be calculating checksum on
something less than skb->len.
2) Adds saving checksum to __skb_checksum_complete. The full packet
checksum 0..skb->len is calculated without adding in pseudo header.
This value is saved in skb->csum and then the pseudo header is added
to that to derive the checksum for validation.
3) In both __skb_checksum_complete_header and __skb_checksum_complete,
set skb->csum_valid to whether checksum of zero was computed. This
allows skb_csum_unnecessary to return true without changing to
CHECKSUM_UNNECESSARY which was done previously.
4) Copy new csum related bits in __copy_skb_header.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its too easy to add thousand of UDP sockets on a particular bucket,
and slow down an innocent multicast receiver.
Early demux is supposed to be an optimization, we should avoid spending
too much time in it.
It is interesting to note __udp4_lib_demux_lookup() only tries to
match first socket in the chain.
10 is the threshold we already have in __udp4_lib_lookup() to switch
to secondary hash.
Fixes: 421b3885bf ("udp: ipv4: Add udp early demux")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: David Held <drheld@google.com>
Cc: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel supports SMP Security Request so don't block increasing security
when we are slave.
Signed-off-by: Marcin Kraglak <marcin.kraglak@tieto.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
The SMP code expects hdev to be unlocked since e.g. crypto functions
will try to (re)lock it. Therefore, we need to release the lock before
calling into smp.c from mgmt.c. Without this we risk a deadlock whenever
the smp_user_confirm_reply() function is called.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Tested-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
A deadlock occurs when PDU containing invalid SMP opcode is received on
Security Manager Channel over LE link and conn->pending_rx_work worker
has not run yet.
When LE link is created l2cap_conn_ready() is called and before
returning it schedules conn->pending_rx_work worker to hdev->workqueue.
Incoming data to SMP fixed channel is handled by l2cap_recv_frame()
which calls smp_sig_channel() to handle the SMP PDU. If
smp_sig_channel() indicates failure l2cap_conn_del() is called to delete
the connection. When deleting the connection, l2cap_conn_del() purges
the pending_rx queue and calls flush_work() to wait for the
pending_rx_work worker to complete.
Since incoming data is handled by a worker running from the same
workqueue as the pending_rx_work is being scheduled on, we will deadlock
on waiting for pending_rx_work to complete.
This patch fixes the deadlock by calling cancel_work_sync() instead of
flush_work().
Signed-off-by: Jukka Taimisto <jtt@codenomicon.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
When cleaning up the HCI state as part of the power-off procedure we can
reuse the hci_stop_discovery() function instead of explicitly sending
HCI command related to discovery. The added benefit of this is that it
takes care of canceling name resolving and inquiry which were not
previously covered by the code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
We'll need to reuse the same logic for stopping discovery also when
cleaning up HCI state when powering off. This patch refactors the code
out to its own function that can later (in a subsequent patch) be used
also for the power off case.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
When inquiry is canceled through the HCI_Cancel_Inquiry command there is
no Inquiry Complete event generated. Instead, all we get is the command
complete for the HCI_Inquiry_Cancel command. This means that we must
call the hci_discovery_set_state() function from the respective command
complete handler in order to ensure that user space knows the correct
discovery state.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
When we store the STK in slave role we should set the correct
authentication information for it. If the pairing is producing a HIGH
security level the STK is considered authenticated, and otherwise it's
considered unauthenticated. This patch fixes the value passed to the
hci_add_ltk() function when adding the STK on the slave side.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Tested-by: Marcin Kraglak <marcin.kraglak@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
When responding to an IO capability request when we're the initiators of
the pairing we will not yet have the remote IO capability information.
Since the conn->auth_type variable is treated as an "absolute"
requirement instead of a hint of what's needed later in the user
confirmation request handler it's important that it doesn't have the
MITM bit set if there's any chance that the remote device doesn't have
the necessary IO capabilities.
This patch adds a clarifying comment so that conn->auth_type is left
untouched in this scenario.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
From the Bluetooth Core Specification 4.1 page 1958:
"if both devices have set the Authentication_Requirements parameter to
one of the MITM Protection Not Required options, authentication stage 1
shall function as if both devices set their IO capabilities to
DisplayOnly (e.g., Numeric comparison with automatic confirmation on
both devices)"
So far our implementation has done user confirmation for all just-works
cases regardless of the MITM requirements, however following the
specification to the word means that we should not be doing confirmation
when neither side has the MITM flag set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Tested-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
The conn->link_key variable tracks the type of link key in use. It is
set whenever we respond to a link key request as well as when we get a
link key notification event.
These two events do not however always guarantee that encryption is
enabled: getting a link key request and responding to it may only mean
that the remote side has requested authentication but not encryption. On
the other hand, the encrypt change event is a certain guarantee that
encryption is enabled. The real encryption state is already tracked in
the conn->link_mode variable through the HCI_LM_ENCRYPT bit.
This patch fixes a check for encryption in the hci_conn_auth function to
use the proper conn->link_mode value and thereby eliminates the chance
of a false positive result.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
The src_type member of struct hci_conn should always reflect the address
type of the src_member. It should never be overridden. There is already
code in place in the command status handler of HCI_LE_Create_Connection
to copy the right initiator address into conn->init_addr_type.
Without this patch, if privacy is enabled, we will send the wrong
address type in the SMP identity address information PDU (it'll e.g.
contain our public address but a random address type).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
Pull Ceph updates from Sage Weil:
"This has a mix of bug fixes and cleanups.
Alex's patch fixes a rare race in RBD. Ilya's patches fix an ENOENT
check when a second rbd image is mapped and a couple memory leaks.
Zheng fixes several issues with fragmented directories and multiple
MDSs. Josh fixes a spin/sleep issue, and Josh and Guangliang's
patches fix setting and unsetting RBD images read-only.
Naturally there are several other cleanups mixed in for good measure"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (23 commits)
rbd: only set disk to read-only once
rbd: move calls that may sleep out of spin lock range
rbd: add ioctl for rbd
ceph: use truncate_pagecache() instead of truncate_inode_pages()
ceph: include time stamp in every MDS request
rbd: fix ida/idr memory leak
rbd: use reference counts for image requests
rbd: fix osd_request memory leak in __rbd_dev_header_watch_sync()
rbd: make sure we have latest osdmap on 'rbd map'
libceph: add ceph_monc_wait_osdmap()
libceph: mon_get_version request infrastructure
libceph: recognize poolop requests in debugfs
ceph: refactor readpage_nounlock() to make the logic clearer
mds: check cap ID when handling cap export message
ceph: remember subtree root dirfrag's auth MDS
ceph: introduce ceph_fill_fragtree()
ceph: handle cap import atomically
ceph: pre-allocate ceph_cap struct for ceph_add_cap()
ceph: update inode fields according to issued caps
rbd: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
...
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
When running RHEL6 userspace on a current upstream kernel, "ip link"
fails to show VF information.
The reason is a kernel<->userspace API change introduced by commit
88c5b5ce5c ("rtnetlink: Call nlmsg_parse() with correct header length"),
after which the kernel does not see iproute2's IFLA_EXT_MASK attribute
in the netlink request.
iproute2 adjusted for the API change in its commit 63338dca4513
("libnetlink: Use ifinfomsg instead of rtgenmsg in rtnl_wilddump_req_filter").
The problem has been noticed before:
http://marc.info/?l=linux-netdev&m=136692296022182&w=2
(Subject: Re: getting VF link info seems to be broken in 3.9-rc8)
We can do better than tell those with old userspace to upgrade. We can
recognize the old iproute2 in the kernel by checking the netlink message
length. Even when including the IFLA_EXT_MASK attribute, its netlink
message is shorter than struct ifinfomsg.
With this patch "ip link" shows VF information in both old and new
iproute2 versions.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to a problem observed when losing a FIN segment that does not
contain data. In such situations, TLP is unable to recover from
*any* tail loss and instead adds at least PTO ms to the
retransmission process, i.e., RTO = RTO + PTO.
Signed-off-by: Per Hurtig <per.hurtig@kau.se>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some fields in "struct net_bridge" aren't available when compiling the
kernel without IPv6 support. Therefore adding a check/macro to skip the
complaining code sections in that case.
Introduced by 2cd4143192
("bridge: memorize and export selected IGMP/MLD querier port")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
"New smatch warnings:
net/bridge/br_multicast.c:1368 br_ip6_multicast_query() error:
we previously assumed 'group' could be null (see line 1349)"
In the rare (sort of broken) case of a query having a Maximum
Response Delay of zero, we could create a potential null pointer
dereference.
Fixing this by skipping the multicast specific MLD Query parsing again
if no multicast group address is available.
Introduced by dc4eb53a99
("bridge: adhere to querier election mechanism specified by RFCs")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull vfs updates from Al Viro:
"This the bunch that sat in -next + lock_parent() fix. This is the
minimal set; there's more pending stuff.
In particular, I really hope to get acct.c fixes merged this cycle -
we need that to deal sanely with delayed-mntput stuff. In the next
pile, hopefully - that series is fairly short and localized
(kernel/acct.c, fs/super.c and fs/namespace.c). In this pile: more
iov_iter work. Most of prereqs for ->splice_write with sane locking
order are there and Kent's dio rewrite would also fit nicely on top of
this pile"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (70 commits)
lock_parent: don't step on stale ->d_parent of all-but-freed one
kill generic_file_splice_write()
ceph: switch to iter_file_splice_write()
shmem: switch to iter_file_splice_write()
nfs: switch to iter_splice_write_file()
fs/splice.c: remove unneeded exports
ocfs2: switch to iter_file_splice_write()
->splice_write() via ->write_iter()
bio_vec-backed iov_iter
optimize copy_page_{to,from}_iter()
bury generic_file_aio_{read,write}
lustre: get rid of messing with iovecs
ceph: switch to ->write_iter()
ceph_sync_direct_write: stop poking into iov_iter guts
ceph_sync_read: stop poking into iov_iter guts
new helper: copy_page_from_iter()
fuse: switch to ->write_iter()
btrfs: switch to ->write_iter()
ocfs2: switch to ->write_iter()
xfs: switch to ->write_iter()
...
Consider the scenario:
For a TCP-style socket, while processing the COOKIE_ECHO chunk in
sctp_sf_do_5_1D_ce(), after it has passed a series of sanity check,
a new association would be created in sctp_unpack_cookie(), but afterwards,
some processing maybe failed, and sctp_association_free() will be called to
free the previously allocated association, in sctp_association_free(),
sk_ack_backlog value is decremented for this socket, since the initial
value for sk_ack_backlog is 0, after the decrement, it will be 65535,
a wrap-around problem happens, and if we want to establish new associations
afterward in the same socket, ABORT would be triggered since sctp deem the
accept queue as full.
Fix this issue by only decrementing sk_ack_backlog for associations in
the endpoint's list.
Fix-suggested-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/core/rtnetlink.c
net/core/skbuff.c
Both conflicts were very simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1d8faf48c7 (net/core: Add VF link state control) added VF link state
control to the netlink VF nested structure, but failed to add a proper entry
for the new structure into the VF policy table. Add the missing entry so
the table and the actual data copied into the netlink nested struct are in
sync.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DRR scheduler requires that items on the active list are work
conserving, i.e. do not hold on to skbs for throttling purposes, etc.
Attaching e.g. tbf renders DRR useless because all other classes on the
active list are delayed as well.
So, warn users that this configuration won't work as expected; we
already do this in couple of other qdiscs, see e.g.
commit b00355db3f
('pkt_sched: sch_hfsc: sch_htb: Add non-work-conserving warning handler')
The 'const' change is needed to avoid compiler warning ("discards 'const'
qualifier from pointer target type").
tested with:
drr_hier() {
parent=$1
classes=$2
for i in $(seq 1 $classes); do
classid=$parent$(printf %x $i)
tc class add dev eth0 parent $parent classid $classid drr
tc qdisc add dev eth0 parent $classid tbf rate 64kbit burst 256kbit limit 64kbit
done
}
tc qdisc add dev eth0 root handle 1: drr
drr_hier 1: 32
tc filter add dev eth0 protocol all pref 1 parent 1: handle 1 flow hash keys dst perturb 1 divisor 32
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to gro_postpull_rcsum for GRO to work with checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In skb_checksum complete, if we need to compute the checksum for the
packet (via skb_checksum) save the result as CHECKSUM_COMPLETE.
Subsequent checksum verification can use this.
Also, added csum_complete_sw flag to distinguish between software and
hardware generated checksum complete, we should always be able to trust
the software computation.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse complained about this bogus extern on definition of
a function.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several instances where a pskb_copy or __pskb_copy is
immediately followed by an skb_clone.
Add a couple of new functions to allow the copy skb to be allocated
from the fclone cache and thus speed up subsequent skb_clone calls.
Cc: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Antonio Quartulli <antonio@meshcoding.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Arvid Brodin <arvid.brodin@alten.se>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Allan Stephens <allan.stephens@windriver.com>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables us to change the vlan protocol for vlan filtering.
We come to be able to filter frames on the basis of 802.1ad vlan tags
through a bridge.
This also changes br->group_addr if it has not been set by user.
This is needed for an 802.1ad bridge.
(See IEEE 802.1Q-2011 8.13.5.)
Furthermore, this sets br->group_fwd_mask_required so that an 802.1ad
bridge can forward the Nearest Customer Bridge group addresses except
for br->group_addr, which should be passed to higher layer.
To change the vlan protocol, write a protocol in sysfs:
# echo 0x88a8 > /sys/class/net/br0/bridge/vlan_protocol
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a bridge is an 802.1ad bridge, it must forward another bridge group
addresses (the Nearest Customer Bridge group addresses).
(For details, see IEEE 802.1Q-2011 8.6.3.)
As user might not want group_fwd_mask to be modified by enabling 802.1ad,
introduce a new mask, group_fwd_mask_required, which indicates addresses
the bridge wants to forward. This will be set by enabling 802.1ad.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables a bridge to have vlan protocol informantion and allows vlan
tag manipulation (retrieve, insert and remove tags) according to the vlan
protocol.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge device doesn't need to embed S-tag into skb->data.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix compiler warning on 32-bit architectures:
net/core/filter.c: In function '__sk_run_filter':
net/core/filter.c:540:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
net/core/filter.c:550:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
net/core/filter.c:560:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 4f4482dcd9 ("tipc: compensate
for double accounting in socket rcv buffer") we access 'truesize' of
a received buffer after it might have been released by the function
filter_rcv().
In this commit we correct this by reading the value of 'truesize' to
the stack before delivering the buffer to filter_rcv().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following sparse warning:
net/sctp/associola.c:1556:29: warning: incorrect type in initializer (different base types)
net/sctp/associola.c:1556:29: expected bool [unsigned] [usertype] preload
net/sctp/associola.c:1556:29: got restricted gfp_t
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function sctp_select_active_and_retran_path(), we walk the
transport list in order to look for the two most recently used
ACTIVE transports (trans_pri, trans_sec). In case we didn't find
anything ACTIVE, we currently just camp on a possibly PF or
INACTIVE transport that is primary path; this behavior actually
dates back to linux-history tree of the very early days of
lksctp, and can yield a behavior that chooses suboptimal
transport paths.
Instead, be a bit more clever by reusing and extending the
recently introduced sctp_trans_elect_best() handler. In case
both transports are evaluated to have the same score resulting
from their states, break the tie by looking at: 1) transport
patch error count 2) last_time_heard value from each transport.
This is analogous to Nishida's Quick Failover draft [1],
section 5.1, 3:
The sender SHOULD avoid data transmission to PF destinations.
When all destinations are in either PF or Inactive state,
the sender MAY either move the destination from PF to active
state (and transmit data to the active destination) or the
sender MAY transmit data to a PF destination. In the former
scenario, (i) the sender MUST NOT notify the ULP about the
state transition, and (ii) MUST NOT clear the destination's
error counter. It is recommended that the sender picks the
PF destination with least error count (fewest consecutive
timeouts) for data transmission. In case of a tie (multiple PF
destinations with same error count), the sender MAY choose the
last active destination.
Thus for sctp_select_active_and_retran_path(), we keep track of
the best, if any, transport that is in PF state and in case no
ACTIVE transport has been found (hence trans_{pri,sec} is NULL),
we select the best out of the three: current primary_path and
retran_path as well as a possible PF transport.
The secondary may still camp on the original primary_path as
before. The change in sctp_trans_elect_best() with a more fine
grained tie selection also improves at the same time path selection
for sctp_assoc_update_retran_path() in case of non-ACTIVE states.
[1] http://tools.ietf.org/html/draft-nishida-tsvwg-sctp-failover-05
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be more precise in transport path selection and use ktime
helpers instead of jiffies to compare and pick the better
primary and secondary recently used transports. This also
avoids any side-effects during a possible roll-over, and
could lead to better path decision-making.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch just refactors and moves the code for the active
path selection into its own helper function outside of
sctp_assoc_control_transport() which is already big enough.
No functional changes here.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two minimal helper functions analogous to time_before() and
time_after() that will later on both be needed by SCTP code.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only one WPAN devices can be active at any given time, so only deliver
packets to that one interface that is actually up. Multiple monitors may
be up at any given time, but we don't have to deliver to monitors that
are down either.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac802154 RX did not free skbs on decryption failure, assuming that the
caller would when the local rx handler returned _DROP. This was false.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a kernel BUG_ON in skb_segment. It is hit when
testing two VMs on openvswitch with one VM acting as VXLAN gateway.
During VXLAN packet GSO, skb_segment is called with skb->data
pointing to inner TCP payload. skb_segment calls skb_network_protocol
to retrieve the inner protocol. skb_network_protocol actually expects
skb->data to point to MAC and it calls pskb_may_pull with ETH_HLEN.
This ends up pulling in ETH_HLEN data from header tail. As a result,
pskb_trim logic is skipped and BUG_ON is hit later.
Move skb_push in front of skb_network_protocol so that skb->data
lines up properly.
kernel BUG at net/core/skbuff.c:2999!
Call Trace:
[<ffffffff816ac412>] tcp_gso_segment+0x122/0x410
[<ffffffff816bc74c>] inet_gso_segment+0x13c/0x390
[<ffffffff8164b39b>] skb_mac_gso_segment+0x9b/0x170
[<ffffffff816b3658>] skb_udp_tunnel_segment+0xd8/0x390
[<ffffffff816b3c00>] udp4_ufo_fragment+0x120/0x140
[<ffffffff816bc74c>] inet_gso_segment+0x13c/0x390
[<ffffffff8109d742>] ? default_wake_function+0x12/0x20
[<ffffffff8164b39b>] skb_mac_gso_segment+0x9b/0x170
[<ffffffff8164b4d0>] __skb_gso_segment+0x60/0xc0
[<ffffffff8164b6b3>] dev_hard_start_xmit+0x183/0x550
[<ffffffff8166c91e>] sch_direct_xmit+0xfe/0x1d0
[<ffffffff8164bc94>] __dev_queue_xmit+0x214/0x4f0
[<ffffffff8164bf90>] dev_queue_xmit+0x10/0x20
[<ffffffff81687edb>] ip_finish_output+0x66b/0x890
[<ffffffff81688a58>] ip_output+0x58/0x90
[<ffffffff816c628f>] ? fib_table_lookup+0x29f/0x350
[<ffffffff816881c9>] ip_local_out_sk+0x39/0x50
[<ffffffff816cbfad>] iptunnel_xmit+0x10d/0x130
[<ffffffffa0212200>] vxlan_xmit_skb+0x1d0/0x330 [vxlan]
[<ffffffffa02a3919>] vxlan_tnl_send+0x129/0x1a0 [openvswitch]
[<ffffffffa02a2cd6>] ovs_vport_send+0x26/0xa0 [openvswitch]
[<ffffffffa029931e>] do_output+0x2e/0x50 [openvswitch]
Signed-off-by: Wei-Chun Chao <weichunc@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug report on https://bugzilla.kernel.org/show_bug.cgi?id=75781
When a local output ipsec packet match the mangle table rule,
and be set mark value, the packet will be route again in
route_me_harder -> _session_decoder6
In this case, the nhoff in CB of skb was still the default
value 0. So the protocal match can't success and the packet can't match
correct SA rule,and then the packet be send out in plaintext.
To fixed up the issue. The CB->nhoff must be set.
Signed-off-by: Hui Zhang <huizhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some tunnels (though only vti as for now) can use i_key just for internal use:
for example vti uses it for fwmark'ing incoming packets. So raw i_key value
shouldn't be treated as a distinguisher for them. ip_tunnel_key_match exists for
cases when we want to compare two ip_tunnel_parms' i_keys.
Example bug:
ip link add type vti ikey 1 local 1.0.0.1 remote 2.0.0.2
ip link add type vti ikey 2 local 1.0.0.1 remote 2.0.0.2
spawned two tunnels, although it doesn't make sense.
Signed-off-by: Dmitry Popov <ixaphire@qrator.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip tunnel add remote 10.2.2.1 local 10.2.2.2 mode vti ikey 1 okey 2
translates to p->iflags = VTI_ISVTI|GRE_KEY and p->i_key = 1, but GRE_KEY !=
TUNNEL_KEY, so ip_tunnel_ioctl would set i_key to 0 (same story with o_key)
making us unable to create vti tunnels with [io]key via ip tunnel.
We cannot simply translate GRE_KEY to TUNNEL_KEY (as GRE module does) because
vti_tunnels with same local/remote addresses but different ikeys will be treated
as different then. So, imo the best option here is to move p->i_flags & *_KEY
check for vti tunnels from ip_tunnel.c to ip_vti.c and to think about [io]_mark
field for ip_tunnel_parm in the future.
Signed-off-by: Dmitry Popov <ixaphire@qrator.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro 'A' used in internal BPF interpreter:
#define A regs[insn->a_reg]
was easily confused with the name of classic BPF register 'A', since
'A' would mean two different things depending on context.
This patch is trying to clean up the naming and clarify its usage in the
following way:
- A and X are names of two classic BPF registers
- BPF_REG_A denotes internal BPF register R0 used to map classic register A
in internal BPF programs generated from classic
- BPF_REG_X denotes internal BPF register R7 used to map classic register X
in internal BPF programs generated from classic
- internal BPF instruction format:
struct sock_filter_int {
__u8 code; /* opcode */
__u8 dst_reg:4; /* dest register */
__u8 src_reg:4; /* source register */
__s16 off; /* signed offset */
__s32 imm; /* signed immediate constant */
};
- BPF_X/BPF_K is 1 bit used to encode source operand of instruction
In classic:
BPF_X - means use register X as source operand
BPF_K - means use 32-bit immediate as source operand
In internal:
BPF_X - means use 'src_reg' register as source operand
BPF_K - means use 32-bit immediate as source operand
Suggested-by: Chema Gonzalez <chema@google.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Chema Gonzalez <chema@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dns_query() credulously assumes that keys are null-terminated and
returns a copy of a memory block that is off by one.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding bridge support to the batman-adv multicast optimization requires
batman-adv knowing about the existence of bridged-in IGMP/MLD queriers
to be able to reliably serve any multicast listener behind this same
bridge.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this new, exported function br_multicast_list_adjacent(net_dev) a
list of IPv4/6 addresses is returned. This list contains all multicast
addresses sensed by the bridge multicast snooping feature on all bridge
ports of the bridge interface of net_dev, excluding addresses from the
specified net_device itself.
Adding bridge support to the batman-adv multicast optimization requires
batman-adv knowing about the existence of bridged-in multicast
listeners to be able to reliably serve them with multicast packets.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
MLDv1 (RFC2710 section 6), MLDv2 (RFC3810 section 7.6.2), IGMPv2
(RFC2236 section 3) and IGMPv3 (RFC3376 section 6.6.2) specify that the
querier with lowest source address shall become the selected
querier.
So far the bridge stopped its querier as soon as it heard another
querier regardless of its source address. This results in the "wrong"
querier potentially becoming the active querier or a potential,
unnecessary querying delay.
With this patch the bridge memorizes the source address of the currently
selected querier and ignores queries from queriers with a higher source
address than the currently selected one. This slight optimization is
supposed to make it more RFC compliant (but is rather uncritical and
therefore probably not necessary to be queued for stable kernels).
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current naming of these two structs is very random, in that
reversing their naming would not make any semantical difference.
This patch tries to make the naming less confusing by giving them a more
specific, distinguishable naming.
This is also useful for the upcoming patches reintroducing the
"struct bridge_mcast_querier" but for storing information about the
selected querier (no matter if our own or a foreign querier).
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4_{update_pmtu,redirect} were called with tunnel's ifindex (t->dev is a
tunnel netdevice). It caused wrong route lookup and failure of pmtu update or
redirect. We should use the same ifindex that we use in ip_route_output_* in
*tunnel_xmit code. It is t->parms.link .
Signed-off-by: Dmitry Popov <ixaphire@qrator.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to require forcing device down on a Ethernet GRE (gretap)
tunnel to change the MAC address.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_fragment can be called from process context (from tso_fragment).
Add a new gfp parameter to allow it to preserve atomic memory if
possible.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Highlights include:
- Massive cleanup of the NFS read/write code by Anna and Dros
- Support multiple NFS read/write requests per page in order to deal with
non-page aligned pNFS striping. Also cleans up the r/wsize < page size
code nicely.
- stable fix for ensuring inode is declared uptodate only after all the
attributes have been checked.
- stable fix for a kernel Oops when remounting
- NFS over RDMA client fixes
- move the pNFS files layout driver into its own subdirectory
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OyXR
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.16-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Highlights include:
- massive cleanup of the NFS read/write code by Anna and Dros
- support multiple NFS read/write requests per page in order to deal
with non-page aligned pNFS striping. Also cleans up the r/wsize <
page size code nicely.
- stable fix for ensuring inode is declared uptodate only after all
the attributes have been checked.
- stable fix for a kernel Oops when remounting
- NFS over RDMA client fixes
- move the pNFS files layout driver into its own subdirectory"
* tag 'nfs-for-3.16-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (79 commits)
NFS: populate ->net in mount data when remounting
pnfs: fix lockup caused by pnfs_generic_pg_test
NFSv4.1: Fix typo in dprintk
NFSv4.1: Comment is now wrong and redundant to code
NFS: Use raw_write_seqcount_begin/end int nfs4_reclaim_open_state
xprtrdma: Disconnect on registration failure
xprtrdma: Remove BUG_ON() call sites
xprtrdma: Avoid deadlock when credit window is reset
SUNRPC: Move congestion window constants to header file
xprtrdma: Reset connection timeout after successful reconnect
xprtrdma: Use macros for reconnection timeout constants
xprtrdma: Allocate missing pagelist
xprtrdma: Remove Tavor MTU setting
xprtrdma: Ensure ia->ri_id->qp is not NULL when reconnecting
xprtrdma: Reduce the number of hardway buffer allocations
xprtrdma: Limit work done by completion handler
xprtrmda: Reduce calls to ib_poll_cq() in completion handlers
xprtrmda: Reduce lock contention in completion handlers
xprtrdma: Split the completion queue
xprtrdma: Make rpcrdma_ep_destroy() return void
...
Pull nfsd updates from Bruce Fields:
"The largest piece is a long-overdue rewrite of the xdr code to remove
some annoying limitations: for example, there was no way to return
ACLs larger than 4K, and readdir results were returned only in 4k
chunks, limiting performance on large directories.
Also:
- part of Neil Brown's work to make NFS work reliably over the
loopback interface (so client and server can run on the same
machine without deadlocks). The rest of it is coming through
other trees.
- cleanup and bugfixes for some of the server RDMA code, from
Steve Wise.
- Various cleanup of NFSv4 state code in preparation for an
overhaul of the locking, from Jeff, Trond, and Benny.
- smaller bugfixes and cleanup from Christoph Hellwig and
Kinglong Mee.
Thanks to everyone!
This summer looks likely to be busier than usual for knfsd. Hopefully
we won't break it too badly; testing definitely welcomed"
* 'for-3.16' of git://linux-nfs.org/~bfields/linux: (100 commits)
nfsd4: fix FREE_STATEID lockowner leak
svcrdma: Fence LOCAL_INV work requests
svcrdma: refactor marshalling logic
nfsd: don't halt scanning the DRC LRU list when there's an RC_INPROG entry
nfs4: remove unused CHANGE_SECURITY_LABEL
nfsd4: kill READ64
nfsd4: kill READ32
nfsd4: simplify server xdr->next_page use
nfsd4: hash deleg stateid only on successful nfs4_set_delegation
nfsd4: rename recall_lock to state_lock
nfsd: remove unneeded zeroing of fields in nfsd4_proc_compound
nfsd: fix setting of NFS4_OO_CONFIRMED in nfsd4_open
nfsd4: use recall_lock for delegation hashing
nfsd: fix laundromat next-run-time calculation
nfsd: make nfsd4_encode_fattr static
SUNRPC/NFSD: Remove using of dprintk with KERN_WARNING
nfsd: remove unused function nfsd_read_file
nfsd: getattr for FATTR4_WORD0_FILES_AVAIL needs the statfs buffer
NFSD: Error out when getting more than one fsloc/secinfo/uuid
NFSD: Using type of uint32_t for ex_nflavors instead of int
...
Pull cgroup updates from Tejun Heo:
"A lot of activities on cgroup side. Heavy restructuring including
locking simplification took place to improve the code base and enable
implementation of the unified hierarchy, which currently exists behind
a __DEVEL__ mount option. The core support is mostly complete but
individual controllers need further work. To explain the design and
rationales of the the unified hierarchy
Documentation/cgroups/unified-hierarchy.txt
is added.
Another notable change is css (cgroup_subsys_state - what each
controller uses to identify and interact with a cgroup) iteration
update. This is part of continuing updates on css object lifetime and
visibility. cgroup started with reference count draining on removal
way back and is now reaching a point where csses behave and are
iterated like normal refcnted objects albeit with some complexities to
allow distinguishing the state where they're being deleted. The css
iteration update isn't taken advantage of yet but is planned to be
used to simplify memcg significantly"
* 'for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (77 commits)
cgroup: disallow disabled controllers on the default hierarchy
cgroup: don't destroy the default root
cgroup: disallow debug controller on the default hierarchy
cgroup: clean up MAINTAINERS entries
cgroup: implement css_tryget()
device_cgroup: use css_has_online_children() instead of has_children()
cgroup: convert cgroup_has_live_children() into css_has_online_children()
cgroup: use CSS_ONLINE instead of CGRP_DEAD
cgroup: iterate cgroup_subsys_states directly
cgroup: introduce CSS_RELEASED and reduce css iteration fallback window
cgroup: move cgroup->serial_nr into cgroup_subsys_state
cgroup: link all cgroup_subsys_states in their sibling lists
cgroup: move cgroup->sibling and ->children into cgroup_subsys_state
cgroup: remove cgroup->parent
device_cgroup: remove direct access to cgroup->children
memcg: update memcg_has_children() to use css_next_child()
memcg: remove tasks/children test from mem_cgroup_force_empty()
cgroup: remove css_parent()
cgroup: skip refcnting on normal root csses and cgrp_dfl_root self css
cgroup: use cgroup->self.refcnt for cgroup refcnting
...
John W. Linville says:
====================
pull request: wireless-next 2014-06-06
Please accept this batch of fixes intended for the 3.16 stream.
For the bluetooth bits, Gustavo says:
"Here some more patches for 3.16. We know that Linus already opened the merge
window, but this is fix only pull request, and most of the patches here are
also tagged for stable."
Along with that, Andrea Merello provides a fix for the broken scanning
in the venerable at76c50x driver...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
unregister_netdevice_many() API is error prone and we had too
many bugs because of dangling LIST_HEAD on stacks.
See commit f87e6f4793 ("net: dont leave active on stack LIST_HEAD")
In fact, instead of making sure no caller leaves an active list_head,
just force a list_del() in the callee. No one seems to need to access
the list after unregister_netdevice_many()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlOTY+wACgkQuseO5dulBZXrIgCdFZyXRojufLLKikWEvHjZ3/k5
KsQAnimtcge+62/IX7YwDjWS+xg9Wt3m
=yPrI
-----END PGP SIGNATURE-----
Merge tag 'llvmlinux-for-v3.16' of git://git.linuxfoundation.org/llvmlinux/kernel
Pull LLVM patches from Behan Webster:
"Next set of patches to support compiling the kernel with clang.
They've been soaking in linux-next since the last merge window.
More still in the works for the next merge window..."
* tag 'llvmlinux-for-v3.16' of git://git.linuxfoundation.org/llvmlinux/kernel:
arm, unwind, LLVMLinux: Enable clang to be used for unwinding the stack
ARM: LLVMLinux: Change "extern inline" to "static inline" in glue-cache.h
all: LLVMLinux: Change DWARF flag to support gcc and clang
net: netfilter: LLVMLinux: vlais-netfilter
crypto: LLVMLinux: aligned-attribute.patch
Now that 3.15 is released, this merges the 'next' branch into 'master',
bringing us to the normal situation where my 'master' branch is the
merge window.
* accumulated work in next: (6809 commits)
ufs: sb mutex merge + mutex_destroy
powerpc: update comments for generic idle conversion
cris: update comments for generic idle conversion
idle: remove cpu_idle() forward declarations
nbd: zero from and len fields in NBD_CMD_DISCONNECT.
mm: convert some level-less printks to pr_*
MAINTAINERS: adi-buildroot-devel is moderated
MAINTAINERS: add linux-api for review of API/ABI changes
mm/kmemleak-test.c: use pr_fmt for logging
fs/dlm/debug_fs.c: replace seq_printf by seq_puts
fs/dlm/lockspace.c: convert simple_str to kstr
fs/dlm/config.c: convert simple_str to kstr
mm: mark remap_file_pages() syscall as deprecated
mm: memcontrol: remove unnecessary memcg argument from soft limit functions
mm: memcontrol: clean up memcg zoneinfo lookup
mm/memblock.c: call kmemleak directly from memblock_(alloc|free)
mm/mempool.c: update the kmemleak stack trace for mempool allocations
lib/radix-tree.c: update the kmemleak stack trace for radix tree allocations
mm: introduce kmemleak_update_trace()
mm/kmemleak.c: use %u to print ->checksum
...
Replaced non-standard C use of Variable Length Arrays In Structs (VLAIS) in
xt_repldata.h with a C99 compliant flexible array member and then calculated
offsets to the other struct members. These other members aren't referenced by
name in this code, however this patch maintains the same memory layout and
padding as was previously accomplished using VLAIS.
Had the original structure been ordered differently, with the entries VLA at
the end, then it could have been a flexible member, and this patch would have
been a lot simpler. However since the data stored in this structure is
ultimately exported to userspace, the order of this structure can't be changed.
This patch makes no attempt to change the existing behavior, merely the way in
which the current layout is accomplished using standard C99 constructs. As such
the code can now be compiled with either gcc or clang.
This version of the patch removes the trailing alignment that the VLAIS
structure would allocate in order to simplify the patch.
Author: Mark Charlebois <charlebm@gmail.com>
Signed-off-by: Mark Charlebois <charlebm@gmail.com>
Signed-off-by: Behan Webster <behanw@converseincode.com>
Signed-off-by: Vinícius Tinti <viniciustinti@gmail.com>
During key removal, the key object is freed, but not taken out of the
llsec key list properly. Fix that.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fencing forces the invalidate to only happen after all prior send
work requests have been completed.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reported by : Devesh Sharma <Devesh.Sharma@Emulex.Com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
This patch refactors the NFSRDMA server marshalling logic to
remove the intermediary map structures. It also fixes an existing bug
where the NFSRDMA server was not minding the device fast register page
list length limitations.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
The rpc code makes available to the NFS server an array of pages to
encod into. The server represents its reply as an xdr buf, with the
head pointing into the first page in that array, the pages ** array
starting just after that, and the tail (if any) sharing any leftover
space in the page used by the head.
While encoding, we use xdr_stream->page_ptr to keep track of which page
we're currently using.
Currently we set xdr_stream->page_ptr to buf->pages, which makes the
head a weird exception to the rule that page_ptr always points to the
page we're currently encoding into. So, instead set it to buf->pages -
1 (the page actually containing the head), and remove the need for a
little unintuitive logic in xdr_get_next_encode_buffer() and
xdr_truncate_encode.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
ip_rt_put(rt) is always called in "error" branches above, but was missed in
skb_cow_head branch. As rt is not yet bound to skb here we have to release it by
hand.
Signed-off-by: Dmitry Popov <ixaphire@qrator.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ceph_monc_wait_osdmap(), which will block until the osdmap with the
specified epoch is received or timeout occurs.
Export both of these as they are going to be needed by rbd.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Add support for mon_get_version requests to libceph. This reuses much
of the ceph_mon_generic_request infrastructure, with one exception.
Older OSDs don't set mon_get_version reply hdr->tid even if the
original request had a non-zero tid, which makes it impossible to
lookup ceph_mon_generic_request contexts by tid in get_generic_reply()
for such replies. As a workaround, we allocate a reply message on the
reply path. This can probably interfere with revoke, but I don't see
a better way.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Recognize poolop requests in debugfs monc dump, fix prink format
specifiers - tid is unsigned.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
To avoid the confusion of having two variables, shrink the function to
only use the parameter variable for looping.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/xen-netback/netback.c
net/core/filter.c
A filter bug fix overlapped some cleanups and a conversion
over to some new insn generation macros.
A xen-netback bug fix overlapped the addition of multi-queue
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF classic->internal converter broke SKF_AD_PKTTYPE extension, since
pkt_type_offset() was failing to find skb->pkt_type field which is defined as:
__u8 pkt_type:3,
fclone:2,
ipvs_property:1,
peeked:1,
nf_trace:1;
Fix it by searching for 3 most significant bits and shift them by 5 at run-time
Fixes: bd4cf0ed33 ("net: filter: rework/optimize internal BPF interpreter's instruction set")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Tested-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/nf_tables fixes for net-next
This patchset contains fixes for recent updates available in your
net-next, they are:
1) Fix double memory allocation for accounting objects that results
in a leak, this slipped through with the new quota extension,
patch from Mathieu Poirier.
2) Fix broken ordering when adding set element transactions.
3) Make sure that objects are released in reverse order in the abort
path, to avoid possible use-after-free when accessing dependencies.
4) Allow to delete several objects (as long as dependencies are
fulfilled) by using one batch. This includes changes in the use
counter semantics of the nf_tables objects.
5) Fix illegal sleeping allocation from rcu callback.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
br_manage_promisc() incorrectly expects br_auto_port() to return only 0
or 1, while it actually returns flags, i.e., a subset of BR_AUTO_MASK.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an MPLS packet requires segmentation then use mpls_features
to determine if the software implementation should be used.
As no driver advertises MPLS GSO segmentation this will always be
the case.
I had not noticed that this was necessary before as software MPLS GSO
segmentation was already being used in my test environment. I believe that
the reason for that is the skbs in question always had fragments and the
driver I used does not advertise NETIF_F_FRAGLIST (which seems to be the
case for most drivers). Thus software segmentation was activated by
skb_gso_ok().
This introduces the overhead of an extra call to skb_network_protocol()
in the case where where CONFIG_NET_MPLS_GSO is set and
skb->ip_summed == CHECKSUM_NONE.
Thanks to Jesse Gross for prompting me to investigate this.
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: YAMAMOTO Takashi <yamamoto@valinux.co.jp>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is available since v3.15-rc5.
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to RFC1035 "[...] the total length of a domain name (i.e.,
label octets and label length octets) is restricted to 255 octets or
less."
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added VXLAN link configuration for sending UDP checksums, and allowing
TX and RX of UDP6 checksums.
Also, call common iptunnel_handle_offloads and added GSO support for
checksums.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call gso_make_checksum. This should have the benefit of using a
checksum that may have been previously computed for the packet.
This also adds NETIF_F_GSO_GRE_CSUM to differentiate devices that
offload GRE GSO with and without the GRE checksum offloaed.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a new netif feature for GSO_UDP_TUNNEL_CSUM. This indicates
that a device is capable of computing the UDP checksum in the
encapsulating header of a UDP tunnel.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call common gso_make_checksum when calculating checksum for a
TCP GSO segment.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating a GSO packet segment we may need to set more than
one checksum in the packet (for instance a TCP checksum and
UDP checksum for VXLAN encapsulation). To be efficient, we want
to do checksum calculation for any part of the packet at most once.
This patch adds csum_start offset to skb_gso_cb. This tracks the
starting offset for skb->csum which is initially set in skb_segment.
When a protocol needs to compute a transport checksum it calls
gso_make_checksum which computes the checksum value from the start
of transport header to csum_start and then adds in skb->csum to get
the full checksum. skb->csum and csum_start are then updated to reflect
the checksum of the resultant packet starting from the transport header.
This patch also adds a flag to skbuff, encap_hdr_csum, which is set
in *gso_segment fucntions to indicate that a tunnel protocol needs
checksum calculation
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call common functions to set checksum for UDP tunnel.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added udp_set_csum and udp6_set_csum functions to set UDP checksums
in packets. These are for simple UDP packets such as those that might
be created in UDP tunnels.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit efe4208 ("ipv6: make lookups simpler and faster") introduced a
regression in udp_v6_mcast_next(), resulting in multicast packets not
reaching the destination sockets under certain conditions.
The packet's IPv6 addresses are wrongly compared to the IPv6 addresses
from the function's socket argument, which indicates the starting point
for looping, instead of the loop variable. If the addresses from the
first socket do not match the packet's addresses, no socket in the list
will match.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 30f38d2fdd.
fib_triestat is surrounded by a big lie: while it claims that it's a
seq_file (fib_triestat_seq_open, fib_triestat_seq_show), it isn't:
static const struct file_operations fib_triestat_fops = {
.owner = THIS_MODULE,
.open = fib_triestat_seq_open,
.read = seq_read,
.llseek = seq_lseek,
.release = single_release_net,
};
Yes, fib_triestat is just a regular file.
A small detail (assuming CONFIG_NET_NS=y) is that while for seq_files
you could do seq_file_net() to get the net ptr, doing so for a regular
file would be wrong and would dereference an invalid pointer.
The fib_triestat lie claimed a victim, and trying to show the file would
be bad for the kernel. This patch just reverts the issue and fixes
fib_triestat, which still needs a rewrite to either be a seq_file or
stop claiming it is.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If rpcrdma_register_external() fails during request marshaling, the
current RPC request is killed. Instead, this RPC should be retried
after reconnecting the transport instance.
The most likely reason for registration failure with FRMR is a
failed post_send, which would be due to a remote transport
disconnect or memory exhaustion. These issues can be recovered
by a retry.
Problems encountered in the marshaling logic itself will not be
corrected by trying again, so these should still kill a request.
Now that we've added a clean exit for marshaling errors, take the
opportunity to defang some BUG_ON's.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
If an error occurs in the marshaling logic, fail the RPC request
being processed, but leave the client running.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Update the cwnd while processing the server's reply. Otherwise the
next task on the xprt_sending queue is still subject to the old
credit window. Currently, no task is awoken if the old congestion
window is still exceeded, even if the new window is larger, and a
deadlock results.
This is an issue during a transport reconnect. Servers don't
normally shrink the credit window, but the client does reset it to
1 when reconnecting so the server can safely grow it again.
As a minor optimization, remove the hack of grabbing the initial
cwnd size (which happens to be RPC_CWNDSCALE) and using that value
as the congestion scaling factor. The scaling value is invariant,
and we are better off without the multiplication operation.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
I would like to use one of the RPC client's congestion algorithm
constants in transport-specific code.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
If the new connection is able to make forward progress, reset the
re-establish timeout. Otherwise it keeps growing even if disconnect
events are rare.
The same behavior as TCP is adopted: reconnect immediately if the
transport instance has been able to make some forward progress.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: Ensure the same max and min constant values are used
everywhere when setting reconnect timeouts.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
GETACL relies on transport layer to alloc memory for reply buffer.
However xprtrdma assumes that the reply buffer (pagelist) has been
pre-allocated in upper layer. This problem was reported by IOL OFA lab
test on PPC.
Signed-off-by: Shirley Ma <shirley.ma@oracle.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Edward Mossman <emossman@iol.unh.edu>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up. Remove HCA-specific clutter in xprtrdma, which is
supposed to be device-independent.
Hal Rosenstock <hal@dev.mellanox.co.il> observes:
> Note that there is OpenSM option (enable_quirks) to return 1K MTU
> in SA PathRecord responses for Tavor so that can be used for this.
> The default setting for enable_quirks is FALSE so that would need
> changing.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Devesh Sharma <Devesh.Sharma@Emulex.Com> reports that after a
disconnect, his HCA is failing to create a fresh QP, leaving
ia_ri->ri_id->qp set to NULL. But xprtrdma still allows RPCs to
wake up and post LOCAL_INV as they exit, causing an oops.
rpcrdma_ep_connect() is allowing the wake-up by leaking the QP
creation error code (-EPERM in this case) to the RPC client's
generic layer. xprt_connect_status() does not recognize -EPERM, so
it kills pending RPC tasks immediately rather than retrying the
connect.
Re-arrange the QP creation logic so that when it fails on reconnect,
it leaves ->qp with the old QP rather than NULL. If pending RPC
tasks wake and exit, LOCAL_INV work requests will flush rather than
oops.
On initial connect, leaving ->qp == NULL is OK, since there are no
pending RPCs that might use ->qp. But be sure not to try to destroy
a NULL QP when rpcrdma_ep_connect() is retried.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
While marshaling an RPC/RDMA request, the inline_{rsize,wsize}
settings determine whether an inline request is used, or whether
read or write chunks lists are built. The current default value of
these settings is 1024. Any RPC request smaller than 1024 bytes is
sent to the NFS server completely inline.
rpcrdma_buffer_create() allocates and pre-registers a set of RPC
buffers for each transport instance, also based on the inline rsize
and wsize settings.
RPC/RDMA requests and replies are built in these buffers. However,
if an RPC/RDMA request is expected to be larger than 1024, a buffer
has to be allocated and registered for that RPC, and deregistered
and released when the RPC is complete. This is known has a
"hardway allocation."
Since the introduction of NFSv4, the size of RPC requests has become
larger, and hardway allocations are thus more frequent. Hardway
allocations are significant overhead, and they waste the existing
RPC buffers pre-allocated by rpcrdma_buffer_create().
We'd like fewer hardway allocations.
Increasing the size of the pre-registered buffers is the most direct
way to do this. However, a blanket increase of the inline thresholds
has interoperability consequences.
On my 64-bit system, rpcrdma_buffer_create() requests roughly 7000
bytes for each RPC request buffer, using kmalloc(). Due to internal
fragmentation, this wastes nearly 1200 bytes because kmalloc()
already returns an 8192-byte piece of memory for a 7000-byte
allocation request, though the extra space remains unused.
So let's round up the size of the pre-allocated buffers, and make
use of the unused space in the kmalloc'd memory.
This change reduces the amount of hardway allocated memory for an
NFSv4 general connectathon run from 1322092 to 9472 bytes (99%).
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Sagi Grimberg <sagig@dev.mellanox.co.il> points out that a steady
stream of CQ events could starve other work because of the boundless
loop pooling in rpcrdma_{send,recv}_poll().
Instead of a (potentially infinite) while loop, return after
collecting a budgeted number of completions.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Acked-by: Sagi Grimberg <sagig@dev.mellanox.co.il>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Change the completion handlers to grab up to 16 items per
ib_poll_cq() call. No extra ib_poll_cq() is needed if fewer than 16
items are returned.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Skip the ib_poll_cq() after re-arming, if the provider knows there
are no additional items waiting. (Have a look at commit ed23a727 for
more details).
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The current CQ handler uses the ib_wc.opcode field to distinguish
between event types. However, the contents of that field are not
reliable if the completion status is not IB_WC_SUCCESS.
When an error completion occurs on a send event, the CQ handler
schedules a tasklet with something that is not a struct rpcrdma_rep.
This is never correct behavior, and sometimes it results in a panic.
To resolve this issue, split the completion queue into a send CQ and
a receive CQ. The send CQ handler now handles only struct rpcrdma_mw
wr_id's, and the receive CQ handler now handles only struct
rpcrdma_rep wr_id's.
Fix suggested by Shirley Ma <shirley.ma@oracle.com>
Reported-by: Rafael Reiter <rafael.reiter@ims.co.at>
Fixes: 5c635e09ce
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=73211
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Klemens Senn <klemens.senn@ims.co.at>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: rpcrdma_ep_destroy() returns a value that is used
only to print a debugging message. rpcrdma_ep_destroy() already
prints debugging messages in all error cases.
Make rpcrdma_ep_destroy() return void instead.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: All remaining callers of rpcrdma_deregister_external()
pass NULL as the last argument, so remove that argument.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
If the selected memory registration mode is not supported by the
underlying provider/HCA, the NFS mount command reports that there was
an invalid mount option, and fails. This is misleading.
Reporting a problem allocating memory is a lot closer to the truth.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
An audit of in-kernel RDMA providers that do not support the FRMR
memory registration shows that several of them support MTHCAFMR.
Prefer MTHCAFMR when FRMR is not supported.
If MTHCAFMR is not supported, only then choose ALLPHYSICAL.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
All kernel RDMA providers except amso1100 support either MTHCAFMR
or FRMR, both of which are faster than REGISTER. amso1100 can
continue to use ALLPHYSICAL.
The only other ULP consumer in the kernel that uses the reg_phys_mr
verb is Lustre.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The MEMWINDOWS and MEMWINDOWS_ASYNC memory registration modes were
intended as stop-gap modes before the introduction of FRMR. They
are now considered obsolete.
MEMWINDOWS_ASYNC is also considered unsafe because it can leave
client memory registered and exposed for an indeterminant time after
each I/O.
At this point, the MEMWINDOWS modes add needless complexity, so
remove them.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: This memory registration mode is slow and was never
meant for use in production environments. Remove it to reduce
implementation complexity.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
An IB provider can invoke rpcrdma_conn_func() in an IRQ context,
thus rpcrdma_conn_func() cannot be allowed to directly invoke
generic RPC functions like xprt_wake_pending_tasks().
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Two memory region leaks were found during testing:
1. rpcrdma_buffer_create: While allocating RPCRDMA_FRMR's
ib_alloc_fast_reg_mr is called and then ib_alloc_fast_reg_page_list is
called. If ib_alloc_fast_reg_page_list returns an error it bails out of
the routine dropping the last ib_alloc_fast_reg_mr frmr region creating a
memory leak. Added code to dereg the last frmr if
ib_alloc_fast_reg_page_list fails.
2. rpcrdma_buffer_destroy: While cleaning up, the routine will only free
the MR's on the rb_mws list if there are rb_send_bufs present. However, in
rpcrdma_buffer_create while the rb_mws list is being built if one of the MR
allocation requests fail after some MR's have been allocated on the rb_mws
list the routine never gets to create any rb_send_bufs but instead jumps to
the rpcrdma_buffer_destroy routine which will never free the MR's on rb_mws
list because the rb_send_bufs were never created. This leaks all the MR's
on the rb_mws list that were created prior to one of the MR allocations
failing.
Issue(2) was seen during testing. Our adapter had a finite number of MR's
available and we created enough connections to where we saw an MR
allocation failure on our Nth NFS connection request. After the kernel
cleaned up the resources it had allocated for the Nth connection we noticed
that FMR's had been leaked due to the coding error described above.
Issue(1) was seen during a code review while debugging issue(2).
Signed-off-by: Allen Andrews <allen.andrews@emulex.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Some rdma devices don't support a fast register page list depth of
at least RPCRDMA_MAX_DATA_SEGS. So xprtrdma needs to chunk its fast
register regions according to the minimum of the device max supported
depth or RPCRDMA_MAX_DATA_SEGS.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Conflicts:
include/net/inetpeer.h
net/ipv6/output_core.c
Changes in net were fixing bugs in code removed in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
When we jump to free_pcpu on failure in alloc_netdev_mqs()
rx and tx queues are not yet allocated, so no need to free them.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that ->newlink() fails before registering
the device, in this case we should just free it, it's
safe to call free_netdev().
Fixes: commit 0e0eee2465 (net: correct error path in rtnl_newlink())
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xfrm_user module registers its pernet init/exit after xfrm
itself so that its net exit function xfrm_user_net_exit() is
executed before xfrm_net_exit() which calls xfrm_state_fini() to
cleanup the SA's (xfrm states). This opens a window between
zeroing net->xfrm.nlsk pointer and deleting all xfrm_state
instances which may access it (via the timer). If an xfrm state
expires in this window, xfrm_exp_state_notify() will pass null
pointer as socket to nlmsg_multicast().
As the notifications are called inside rcu_read_lock() block, it
is sufficient to retrieve the nlsk socket with rcu_dereference()
and check the it for null.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
Pull request: Fixes for new ethtool RSS commands
This addresses several problems I previously identified with the new
ETHTOOL_{G,S}RSSH commands:
1. Missing validation of reserved parameters
2. Vague documentation
3. Use of unnamed magic number
4. No consolidation with existing driver operations
I don't currently have access to suitable network hardware, but have
tested these changes with a dummy driver that can support various
combinations of operations and sizes, together with (a) Debian's ethtool
3.13 (b) ethtool 3.14 with the submitted patch to use ETHTOOL_{G,S}RSSH
and minor adjustment for fixes 1 and 3.
v2: Update RSS operations in vmxnet3 too
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ETHTOOL_{G,S}RXFHINDIR and ETHTOOL_{G,S}RSSH should work for drivers
regardless of whether they expose the hash key, unless you try to
set a hash key for a driver that doesn't expose it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
(This patch was previously posted as RFC at
http://patchwork.ozlabs.org/patch/352677/)
This patch adds NDA_MASTER attribute to neighbour attributes enum for
bridge/master ifindex. And adds NDA_MASTER to bridge fdb notify msgs.
Today bridge fdb notifications dont contain bridge information.
Userspace can derive it from the port information in the fdb
notification. However this is tricky in some scenarious.
Example, bridge port delete notification comes before bridge fdb
delete notifications. And we have seen problems in userspace
when using libnl where, the bridge fdb delete notification handling code
does not understand which bridge this fdb entry is part of because
the bridge and port association has already been deleted.
And these notifications (port membership and fdb) are generated on
separate rtnl groups.
Fixing the order of notifications could possibly solve the problem
for some cases (I can submit a separate patch for that).
This patch chooses to add NDA_MASTER to bridge fdb notify msgs
because it not only solves the problem described above, but also helps
userspace avoid another lookup into link msgs to derive the master index.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__sk_prepare_filter() was reworked in commit bd4cf0ed3 (net: filter:
rework/optimize internal BPF interpreter's instruction set) so that it should
have uncharged memory once things went wrong. However that work isn't complete.
Error is handled only in __sk_migrate_filter() while memory can still leak in
the error path right after sk_chk_filter().
Fixes: bd4cf0ed33 ("net: filter: rework/optimize internal BPF interpreter's instruction set")
Signed-off-by: Leon Yu <chianglungyu@gmail.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Tested-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bug is discovered by an recent F-RTO issue on tcpm list
https://www.ietf.org/mail-archive/web/tcpm/current/msg08794.html
The bug is that currently F-RTO does not use DSACK to undo cwnd in
certain cases: upon receiving an ACK after the RTO retransmission in
F-RTO, and the ACK has DSACK indicating the retransmission is spurious,
the sender only calls tcp_try_undo_loss() if some never retransmisted
data is sacked (FLAG_ORIG_DATA_SACKED).
The correct behavior is to unconditionally call tcp_try_undo_loss so
the DSACK information is used properly to undo the cwnd reduction.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make fib_triestat_seq_show consistent with other /proc/net files and
use seq_file_net.
Signed-off-by: David Ahern <dsahern@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was possible to get a setuid root or setcap executable to write to
it's stdout or stderr (which has been set made a netlink socket) and
inadvertently reconfigure the networking stack.
To prevent this we check that both the creator of the socket and
the currentl applications has permission to reconfigure the network
stack.
Unfortunately this breaks Zebra which always uses sendto/sendmsg
and creates it's socket without any privileges.
To keep Zebra working don't bother checking if the creator of the
socket has privilege when a destination address is specified. Instead
rely exclusively on the privileges of the sender of the socket.
Note from Andy: This is exactly Eric's code except for some comment
clarifications and formatting fixes. Neither I nor, I think, anyone
else is thrilled with this approach, but I'm hesitant to wait on a
better fix since 3.15 is almost here.
Note to stable maintainers: This is a mess. An earlier series of
patches in 3.15 fix a rather serious security issue (CVE-2014-0181),
but they did so in a way that breaks Zebra. The offending series
includes:
commit aa4cf9452f
Author: Eric W. Biederman <ebiederm@xmission.com>
Date: Wed Apr 23 14:28:03 2014 -0700
net: Add variants of capable for use on netlink messages
If a given kernel version is missing that series of fixes, it's
probably worth backporting it and this patch. if that series is
present, then this fix is critical if you care about Zebra.
Cc: stable@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed we were sending wrong IPv4 ID in TCP flows when MTU discovery
is disabled.
Note how GSO/TSO packets do not have monotonically incrementing ID.
06:37:41.575531 IP (id 14227, proto: TCP (6), length: 4396)
06:37:41.575534 IP (id 14272, proto: TCP (6), length: 65212)
06:37:41.575544 IP (id 14312, proto: TCP (6), length: 57972)
06:37:41.575678 IP (id 14317, proto: TCP (6), length: 7292)
06:37:41.575683 IP (id 14361, proto: TCP (6), length: 63764)
It appears I introduced this bug in linux-3.1.
inet_getid() must return the old value of peer->ip_id_count,
not the new one.
Lets revert this part, and remove the prevention of
a null identification field in IPv6 Fragment Extension Header,
which is dubious and not even done properly.
Fixes: 87c48fa3b4 ("ipv6: make fragment identifications less predictable")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_handle_local_finish() is allowing us to insert an FDB entry with
disallowed vlan. For example, when port 1 and 2 are communicating in
vlan 10, and even if vlan 10 is disallowed on port 3, port 3 can
interfere with their communication by spoofed src mac address with
vlan id 10.
Note: Even if it is judged that a frame should not be learned, it should
not be dropped because it is destined for not forwarding layer but higher
layer. See IEEE 802.1Q-2011 8.13.10.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-06-02
Please pull this remaining batch of updates intended for the 3.16 stream...
For the mac80211 bits, Johannes says:
"The remainder for -next right now is mostly fixes, and a handful of
small new things like some CSA infrastructure, the regdb script mW/dBm
conversion change and sending wiphy notifications."
For the bluetooth bits, Gustavo says:
"Some more patches for 3.16. There is nothing really special here, just a
bunch of clean ups, fixes plus some small improvements. Please pull."
For the nfc bits, Samuel says:
"We have:
- Felica (Type3) tags support for trf7970a
- Type 4b tags support for port100
- st21nfca DTS typo fix
- A few sparse warning fixes"
For the atheros bits, Kalle says:
"Ben added support for setting antenna configurations. Michal improved
warm reset so that we would not need to fall back to cold reset that
often, an issue where ath10k stripped protected flag while in monitor
mode and made module initialisation asynchronous to fix the problems
with firmware loading when the driver is linked to the kernel.
Luca removed unused channel_switch_beacon callbacks both from ath9k and
ath10k. Marek fixed Protected Management Frames (PMF) when using Action
Frames. Also we had other small fixes everywhere in the driver."
Along with that, there are a handful of updates to a variety
of drivers. This includes updates to at76c50x-usb, ath9k, b43,
brcmfmac, mwifiex, rsi, rtlwifi, and wil6210.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ideally, we would need to generate IP ID using a per destination IP
generator.
linux kernels used inet_peer cache for this purpose, but this had a huge
cost on servers disabling MTU discovery.
1) each inet_peer struct consumes 192 bytes
2) inetpeer cache uses a binary tree of inet_peer structs,
with a nominal size of ~66000 elements under load.
3) lookups in this tree are hitting a lot of cache lines, as tree depth
is about 20.
4) If server deals with many tcp flows, we have a high probability of
not finding the inet_peer, allocating a fresh one, inserting it in
the tree with same initial ip_id_count, (cf secure_ip_id())
5) We garbage collect inet_peer aggressively.
IP ID generation do not have to be 'perfect'
Goal is trying to avoid duplicates in a short period of time,
so that reassembly units have a chance to complete reassembly of
fragments belonging to one message before receiving other fragments
with a recycled ID.
We simply use an array of generators, and a Jenkin hash using the dst IP
as a key.
ipv6_select_ident() is put back into net/ipv6/ip6_output.c where it
belongs (it is only used from this file)
secure_ip_id() and secure_ipv6_id() no longer are needed.
Rename ip_select_ident_more() to ip_select_ident_segs() to avoid
unnecessary decrement/increment of the number of segments.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change provides a function to be used in order to break the
ndo_set_rx_mode call into a set of address add and remove calls. The code
is based on the implementation of dev_uc_sync/dev_mc_sync. Since they
essentially do the same thing but with only one dev I simply named my
functions __dev_uc_sync/__dev_mc_sync.
I also implemented an unsync version of the functions as well to allow for
cleanup on close.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix a off by one error while fragmentation. If the frag_cap
value is equal to skb_unprocessed value we need to stop the
fragmentation loop because the last fragment which has a size of
skb_unprocessed fits into the frag capability size.
This issue was introduced by commit d4b2816d67
("6lowpan: fix fragmentation").
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the 6LoWPAN fragmentation for the case if we have exactly
two fragments. The problem is that the (skb_unprocessed >= frag_cap)
condition is always false on the second fragment after sending the first
fragment. A fragmentation with only one fragment doesn't make any sense.
The solution is that we use a do while loop here, that ensures we sending
always a minimum of two fragments if we need a fragmentation.
This issue was introduced by commit d4b2816d67
("6lowpan: fix fragmentation").
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the local variable ops and n_ops were just read out from family,
and not changed, hence no need to assign back.
Validation functions should operate on const parameters and not
change anything.
Signed-off-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-[0x01 Introduction
We have found a programming error causing a deadlock in Bluetooth subsystem
of Linux kernel. The problem is caused by missing release_sock() call when
L2CAP connection creation fails due full accept queue.
The issue can be reproduced with 3.15-rc5 kernel and is also present in
earlier kernels.
-[0x02 Details
The problem occurs when multiple L2CAP connections are created to a PSM which
contains listening socket (like SDP) and left pending, for example,
configuration (the underlying ACL link is not disconnected between
connections).
When L2CAP connection request is received and listening socket is found the
l2cap_sock_new_connection_cb() function (net/bluetooth/l2cap_sock.c) is called.
This function locks the 'parent' socket and then checks if the accept queue
is full.
1178 lock_sock(parent);
1179
1180 /* Check for backlog size */
1181 if (sk_acceptq_is_full(parent)) {
1182 BT_DBG("backlog full %d", parent->sk_ack_backlog);
1183 return NULL;
1184 }
If case the accept queue is full NULL is returned, but the 'parent' socket
is not released. Thus when next L2CAP connection request is received the code
blocks on lock_sock() since the parent is still locked.
Also note that for connections already established and waiting for
configuration to complete a timeout will occur and l2cap_chan_timeout()
(net/bluetooth/l2cap_core.c) will be called. All threads calling this
function will also be blocked waiting for the channel mutex since the thread
which is waiting on lock_sock() alread holds the channel mutex.
We were able to reproduce this by sending continuously L2CAP connection
request followed by disconnection request containing invalid CID. This left
the created connections pending configuration.
After the deadlock occurs it is impossible to kill bluetoothd, btmon will not
get any more data etc. requiring reboot to recover.
-[0x03 Fix
Releasing the 'parent' socket when l2cap_sock_new_connection_cb() returns NULL
seems to fix the issue.
Signed-off-by: Jukka Taimisto <jtt@codenomicon.com>
Reported-by: Tommi Mäkilä <tmakila@codenomicon.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Use GFP_ATOMIC allocations when sending removal notifications of
anonymous sets from rcu callback context. Sleeping in that context
is illegal.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Three changes to allow the deletion of several objects with dependencies
in one transaction, they are:
1) Introduce speculative counter increment/decrement that is undone in
the abort path if required, thus we avoid hitting -EBUSY when deleting
the chain. The counter updates are reverted in the abort path.
2) Increment/decrement table/chain use counter for each set/rule. We need
this to fully rely on the use counters instead of the list content,
eg. !list_empty(&chain->rules) which evaluate true in the middle of the
transaction.
3) Decrement table use counter when an anonymous set is bound to the
rule in the commit path. This avoids hitting -EBUSY when deleting
the table that contains anonymous sets. The anonymous sets are released
in the nf_tables_rule_destroy path. This should not be a problem since
the rule already bumped the use counter of the chain, so the bound
anonymous set reflects dependencies through the rule object, which
already increases the chain use counter.
So the general assumption after this patch is that the use counters are
bumped by direct object dependencies.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There's no rbtree rcu version yet, so let's fall back on the spinlock
to protect the concurrent access of this structure both from user
(to update the set content) and kernel-space (in the packet path).
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The patch c7c32e7 ("netfilter: nf_tables: defer all object release via
rcu") indicates that we always release deleted objects in the reverse
order, but that is only needed in the abort path. These are the two
possible scenarios when releasing objects:
1) Deletion scenario in the commit path: no need to release objects in
the reverse order since userspace already ensures that dependencies are
fulfilled), ie. userspace tells us to delete rule -> ... -> rule ->
chain -> table. In this case, we have to release the objects in the
*same order* as userspace provided.
2) Deletion scenario in the abort path: we have to iterate in the reverse
order to undo what it cannot be added, ie. userspace sent us a batch
that includes: table -> chain -> rule -> ... -> rule, and that needs to
be partially undone. In this case, we have to release objects in the
reverse order to ensure that the set and chain objects point to valid
rule and table objects.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The transaction needs to be placed at the end of the commit list,
otherwise event notifications are reordered and we may crash when
releasing object via call_rcu.
This problem was introduced in 60319eb ("netfilter: nf_tables: use new
transaction infrastructure to handle elements").
Reported-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Allocation of memory need only to happen once, that is
after the proper checks on the NFACCT_FLAGS have been
done. Otherwise the code can return without freeing
already allocated memory.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When checking whether a legacy link key provides at least HIGH security
level we also need to check for FIPS level which is one step above HIGH.
This patch fixes a missing check in the hci_link_key_request_evt()
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
Commit 9739eef13c ("net: filter: make BPF conversion more readable")
started to introduce helper macros similar to BPF_STMT()/BPF_JUMP()
macros from classic BPF.
However, quite some statements in the filter conversion functions
remained in the old style which gives a mixture of block macros and
non block macros in the code. This patch makes the block macros itself
more readable by using explicit member initialization, and converts
the remaining ones where possible to remain in a more consistent state.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There has been a number incidents recently where customers running KVM have
reported that VM hosts on different Hypervisors are unreachable. Based on
pcap traces we found that the bridge was broadcasting the ARP request out
onto the network. However some NICs have an inbuilt switch which on occasions
were broadcasting the VMs ARP request back through the physical NIC on the
Hypervisor. This resulted in the bridge changing ports and incorrectly learning
that the VMs mac address was external. As a result the ARP reply was directed
back onto the external network and VM never updated it's ARP cache. This patch
will notify the bridge command, after a fdb has been updated to identify such
port toggling.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As commit 2796d0c648 ("bridge: Automatically manage port
promiscuous mode."), make the add_if use dev_set_allmulti
instead of dev_set_promiscuous, so when add_if failed, we
should do dev_set_allmulti(dev, -1).
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Reviewed-by: Amos Kong <akong@redhat.com>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After 1e785f48d2 ("net: Start with correct mac_len in
skb_network_protocol") skb->mac_len is used as a start of the
calculation in skb_network_protocol() but that is not always correct. If
skb->protocol == 8021Q/AD, usually the vlan header is already inserted
in the skb (i.e. vlan reorder hdr == 0). Usually when the packet enters
dev_hard_xmit it has mac_len == 0 so we take 2 bytes from the
destination mac address (skb->data + VLAN_HLEN) as a type in
skb_network_protocol() and return vlan_depth == 4. In the case where TSO is
off, then the mac_len is set but it's == 18 (ETH_HLEN + VLAN_HLEN), so
skb_network_protocol() returns a type from inside the packet and
offset == 22. Also make vlan_depth unsigned as suggested before.
As suggested by Eric Dumazet, move the while() loop in the if() so we
can avoid additional testing in fast path.
Here are few netperf tests + debug printk's to illustrate:
cat netperf.tso-on.reorder-on.bugged
- Vlan -> device (reorder on, default, this case is okay)
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
192.168.3.1 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 7111.54
[ 81.605435] skb->len 65226 skb->gso_size 1448 skb->proto 0x800
skb->mac_len 0 vlan_depth 0 type 0x800
- Vlan -> device (reorder off, bad)
cat netperf.tso-on.reorder-off.bugged
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
192.168.3.1 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 241.35
[ 204.578332] skb->len 1518 skb->gso_size 0 skb->proto 0x8100
skb->mac_len 0 vlan_depth 4 type 0x5301
0x5301 are the last two bytes of the destination mac.
And if we stop TSO, we may get even the following:
[ 83.343156] skb->len 2966 skb->gso_size 1448 skb->proto 0x8100
skb->mac_len 18 vlan_depth 22 type 0xb84
Because mac_len already accounts for VLAN_HLEN.
After the fix:
cat netperf.tso-on.reorder-off.fixed
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
192.168.3.1 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.01 5001.46
[ 81.888489] skb->len 65230 skb->gso_size 1448 skb->proto 0x8100
skb->mac_len 0 vlan_depth 18 type 0x800
CC: Vlad Yasevich <vyasevic@redhat.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Daniel Borkman <dborkman@redhat.com>
CC: David S. Miller <davem@davemloft.net>
Fixes:1e785f48d29a ("net: Start with correct mac_len in
skb_network_protocol")
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to recent changes to the way that the MITM requirement is set for
outgoing pairing attempts we can no longer rely on the hcon->auth_type
variable (which is actually good since it was formed from BR/EDR
concepts that don't really exist for SMP).
To match the logic that BR/EDR now uses simply rely on the local IO
capability and/or needed security level to set the MITM requirement for
outgoing pairing requests.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
- prevent NULL dereference in multicast code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=fvfu
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- prevent NULL dereference in multicast code
Antonion Quartulli says:
====================
pull request net: batman-adv 20140527
here you have another very small fix intended for net/linux-3.15.
It prevents some multicast functions from dereferencing a NULL pointer.
(Actually it was nothing more than a typo)
I hope it is not too late for such a small patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Was introduced with 4c8755d69c
("batman-adv: Send multicast packets to nodes with a WANT_ALL flag")
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Acked-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Default values for various channel settings were missing. This
way channel users do not need to set default values themselves.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The universal/local bit handling was incorrectly done in the code.
So when setting EUI address from BD address we do this:
- If BD address type is PUBLIC, then we clear the universal bit
in EUI address. If the address type is RANDOM, then the universal
bit is set (BT 6lowpan draft chapter 3.2.2)
- After this we invert the universal/local bit according to RFC 2464
When figuring out BD address we do the reverse:
- Take EUI address from stateless IPv6 address, invert the
universal/local bit according to RFC 2464
- If universal bit is 1 in this modified EUI address, then address
type is set to RANDOM, otherwise it is PUBLIC
Note that 6lowpan_iphc.[ch] does the final toggling of U/L bit
before sending or receiving the network packet.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
When checking whether we need to request authentication or not we should
include HCI_SECURITY_FIPS to the levels that always need authentication.
This patch fixes check for it in the hci_outgoing_auth_needed()
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
In case there are new LTK types in the future we shouldn't just blindly
assume that != MGMT_LTK_UNAUTHENTICATED means that the key is
authenticated. This patch adds explicit checks for each allowed key type
in the form of a switch statement and skips any key which has an unknown
value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
Pablo Neira Ayuso says:
====================
The following patchset contains a late fix for IPVS:
* Fix crash when trying to remove the transport header with non-linear
skbuffs, this was introduced in 3.6-rc. Patch from Peter Christensen
via the IPVS folks.
I'll pass this to -stable once this hits mainstream.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
This small patchset contains three accumulated Netfilter/IPVS updates,
they are:
1) Refactorize common NAT code by encapsulating it into a helper
function, similarly to what we do in other conntrack extensions,
from Florian Westphal.
2) A minor format string mismatch fix for IPVS, from Masanari Iida.
3) Add quota support to the netfilter accounting infrastructure, now
you can add quotas to accounting objects via the nfnetlink interface
and use them from iptables. You can also listen to quota
notifications from userspace. This enhancement from Mathieu Poirier.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces a comma between expression statements by a semicolon.
A simplified version of the semantic patch that performs this
transformation is as follows:
// <smpl>
@r@
expression e1,e2,e;
type T;
identifier i;
@@
e1
-,
+;
e2;
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces a comma between expression statements by a semicolon.
A simplified version of the semantic patch that performs this
transformation is as follows:
// <smpl>
@r@
expression e1,e2,e;
type T;
identifier i;
@@
e1
-,
+;
e2;
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces a comma between expression statements by a semicolon.
A simplified version of the semantic patch that performs this
transformation is as follows:
// <smpl>
@r@
expression e1,e2,e;
type T;
identifier i;
@@
e1
-,
+;
e2;
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces a comma between expression statements by a semicolon.
A simplified version of the semantic patch that performs this
transformation is as follows:
// <smpl>
@r@
expression e1,e2,e;
type T;
identifier i;
@@
e1
-,
+;
e2;
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of transport HIPER a sock struct is allocated for an incoming
connect request. If the backlog queue is full this socket is not
needed, but is left in the list of af_iucv sockets. Final socket
release posts console message "Attempt to release alive iucv socket".
This patch makes sure the new created socket is cleaned up correctly
if the backlog queue is full.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Reported-by: Philipp Hachtmann <phacht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a socket is bound to an address using before calling connect
it is usual to leave it to the network system to choose an appropriate
outgoing application name respective port address.
af_iucv on VM uses a counter and uses simple numbers as unique identifiers.
This behaviour was missing when af_iucv is used with HiperSockets.
This patch contains a simple approach to harmonize af_iucv's behaviour.
Signed-off-by: Philipp Hachtmann <phacht@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When debugging, rpc prints messages from dprintk(KERN_WARNING ...)
with "^A4" prefixed,
[ 2780.339988] ^A4nfsd: connect from unprivileged port: 127.0.0.1, port=35316
Trond tells,
> dprintk != printk. We have NEVER supported dprintk(KERN_WARNING...)
This patch removes using of dprintk with KERN_WARNING.
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
John W. Linville says:
====================
Please pull this batch of updates intended for 3.16...
For the mac80211 bits, Johannes says:
"Here I just have Heikki's rfkill GPIO cleanups.
The ARM/tegra patch is OK with the maintainer (Stephen). Let me know of
any problems."
and;
"We have a whole bunch of work on CSA by Andrei, Luca and Michal, but
unfortunately it doesn't seem quite complete yet so it's still disabled.
There's some TDLS work from Arik, and the rest is mostly minor fixes and
cleanups."
For the NFC bits, Samuel says:
"This is the NFC pull request for 3.16. We have:
- STMicroeectronics st21nfca support. The st21nfca is an HCI chipset and
thus relies on the HCI stack. This submission provides support for tag
redaer/writer mode (including Type 5) and device tree bindings.
- PM runtime support and a bunch of bug fixes for TI's trf7970a.
- Device tree support for NXP's pn544. Legacy platform data support is
obviously kept intact.
- NFC Tag type 4B support to the NFC Digital stack.
- SOCK_RAW type support to the raw NFC socket, and allow NCI
sniffing from that. This can be extended to report HCI frames and also
proprietarry ones like e.g. the pn533 ones."
For the iwlwifi bits, Emmanuel says:
"Eran continues to work on new devices, Eyal is still digging in
the rate control stuff, and Johannes added new functionality to the
debug system we have in place now along with a few cleanups he made
on the way. That's pretty much it."
and;
"Avri continues to work on the power code and Eran is improving the
NVM handling as a preparations for new devices on which he works
with Liad. Luca cleans up a bit the code while working on CSA. I have
the regular BT Coex stuff and a small lockdep fix. Johannes has his
regular amount of clean ups and improvements, the main one is the
ability to leave 2 chains open to improve diversity and hence the
throughput in high attenuation scenarios."
and;
"The regular amount of housekeeping here. I merged iwlwifi-fixes.git to
be able to add the patch you didn't want in wireless.git at that stage
of the -rc cycle. Luca has a few preparations for CSA implementation
and also what seems to be a bugfix for P2P but hasn't caused issues
we could notice."
For the Atheros bits, Kalle says:
"For ath10k Michal did various small fixes on how we handle
hardware/firmware problems and he also fixed two memory leaks."
Also included are a couple of pulls from the wireless tree to
avoid/resolve merge issues...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This preprocessor check is commented out ever since this file was added
during the v2.3 development cycle. It is unclear what it purpose might
have been. Whatever it was, it can safely be removed now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
RPC_MAX_AUTH_SIZE is scattered around several places. Better to set it
once in the auth code, where this kind of estimate should be made. And
while we're at it we can leave it zero when we're not using krb5i or
krb5p.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
After this we can handle for example getattr of very large ACLs.
Read, readdir, readlink are still special cases with their own limits.
Also we can't handle a new operation starting close to the end of a
page.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
This will be used in the server side in a few cases:
- when certain operations (read, readdir, readlink) fail after
encoding a partial response.
- when we run out of space after encoding a partial response.
- in readlink, where we initially reserve PAGE_SIZE bytes for
data, then truncate to the actual size.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
This is the 2nd NFC pull request for 3.16. We have:
- Felica (Type3) tags support for trf7970a
- Type 4b tags support for port100
- st21nfca DTS typo fix
- A few sparse warning check fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=t52d
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-3.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"NFC: 3.16: Second pull request
This is the 2nd NFC pull request for 3.16. We have:
- Felica (Type3) tags support for trf7970a
- Type 4b tags support for port100
- st21nfca DTS typo fix
- A few sparse warning check fixes"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark new interfaces as idle to allow operations that require that
interfaces are idle to take place. Interface types that are always
not idle (like AP interfaces) will be set as not idle when they are
assigned a channel context.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach<emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During strong signal fluctuations under high throughput, few consecutive
failed A-MPDU transmissions can easily trigger packet loss notification,
and thus (in AP mode) client disconnection.
Reduce the number of false positives by checking the A-MPDU status flag
and treating a failed A-MPDU as a single packet.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Doing so will lead to an oops for a p2p-dev interface, since it has
no netdev.
Cc: stable@vger.kernel.org
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the rate control algorithm uses a selection table, it
is leaked when the station is destroyed - fix that.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Christophe Prévotaux <cprevotaux@nltinc.com>
Fixes: 0d528d85c5 ("mac80211: improve the rate control API")
Cc: stable@vger.kernel.org # v3.10+
[add commit log entry, remove pointless NULL check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Generalize the power conversion from mW to dBm
using log. This should fix the below compilation
error for country NO which adds a new power value
2000mW which is not handled earlier.
CC [M] net/wireless/wext-sme.o
CC [M] net/wireless/regdb.o
net/wireless/regdb.c:1130:1: error: Unknown undeclared here (not in
a function)
net/wireless/regdb.c:1130:9: error: expected } before power
make[2]: *** [net/wireless/regdb.o] Error 1
make[1]: *** [net/wireless] Error 2
make: *** [net] Error 2
Reported-By: John Walker <john@x109.net>
Signed-off-by: Chaitanya T K <chaitanya.mgit@gmail.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
[remove unneeded parentheses, fix rounding by using %.0f]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Without this fix, freshly rebooted Linux creates a new IBSS
instead of joining an existing one. Only when jiffies counter
overflows after 5 minutes the IBSS can be successfully joined.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
[edit commit message slightly]
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We're currently sending NEW_WIPHY events for renames (which
is a bit odd, but now can't be changed), but also send them
for really new devices that register.
Also send DEL_WIPHY events when a device is removed, the
event ID for this was already reserved.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the commit below, cfg80211_chandef_dfs_required()
will warn if it gets a an NL80211_IFTYPE_UNSPECIFIED iftype
as explicitely written in the commit log.
When an virtual monitor interface is added, its type is set
in ieee80211_sub_if_data.vif.type, but not in
ieee80211_sub_if_data.wdev.iftype which is passed to
cfg80211_chandef_dfs_required() hence resulting in the
following warning:
WARNING: CPU: 1 PID: 21265 at net/wireless/chan.c:376 cfg80211_chandef_dfs_required+0xbc/0x130 [cfg80211]()
Modules linked in: [...]
CPU: 1 PID: 21265 Comm: ifconfig Tainted: G W O 3.13.11+ #12
Hardware name: Dell Inc. Latitude E6410/0667CC, BIOS A01 03/05/2010
0000000000000009 ffff88008f5fdb08 ffffffff817d4219 ffff88008f5fdb50
ffff88008f5fdb40 ffffffff8106f57d 0000000000000000 0000000000000000
ffff880081062fb8 ffff8800810604e0 0000000000000001 ffff88008f5fdba0
Call Trace:
[<ffffffff817d4219>] dump_stack+0x4d/0x66
[<ffffffff8106f57d>] warn_slowpath_common+0x7d/0xa0
[<ffffffff8106f5ec>] warn_slowpath_fmt+0x4c/0x50
[<ffffffffa04ea4ec>] cfg80211_chandef_dfs_required+0xbc/0x130 [cfg80211]
[<ffffffffa06b1024>] ieee80211_vif_use_channel+0x94/0x500 [mac80211]
[<ffffffffa0684e6b>] ieee80211_add_virtual_monitor+0x1ab/0x5c0 [mac80211]
[<ffffffffa0686ae5>] ieee80211_do_open+0xe75/0x1580 [mac80211]
[<ffffffffa0687259>] ieee80211_open+0x69/0x70 [mac80211]
[snip]
Fixes: 00ec75fc5a ("cfg80211: pass the actual iftype when calling cfg80211_chandef_dfs_required()")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, when the driver is already using all the channel
contexts it can handle at once, we have to do an in-place switch
(ie. we cannot afford using an extra context temporarily for the
transaction). But some drivers may not support switching the channel
context assigned to a vif on the fly (ie. without unassigning and
assigning it) while others may only work if the context is changed on
the fly, without unassigning it first.
To allow these different scenarios, add a new driver operation that
let's the driver decide how to handle an in-place switch.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Before f5efc69 ("netfilter: nf_tables: Add meta expression key for
bridge interface name"), the entire net/bridge/netfilter/ directory
depended on BRIDGE_NF_EBTABLES, ie. on ebtables. However, that
directory already contained the nf_tables bridge extension that
we should allow to compile separately. In f5efc69, we tried to
generalize this by using CONFIG_BRIDGE_NETFILTER which was not a good
idea since this option already existed and it is dedicated to enable
the Netfilter bridge IP/ARP filtering.
Let's try to fix this mess by:
1) making net/bridge/netfilter/ dependent on the toplevel
CONFIG_NETFILTER option, just like we do with the net/netfilter and
net/ipv{4,6}/netfilter/ directories.
2) Changing 'selects' to 'depends on' NETFILTER_XTABLES for
BRIDGE_NF_EBTABLES. I believe this problem was already before
f5efc69:
warning: (BRIDGE_NF_EBTABLES) selects NETFILTER_XTABLES which has
unmet direct dependencies (NET && INET && NETFILTER)
3) Fix ebtables/nf_tables bridge dependencies by making NF_TABLES_BRIDGE
and BRIDGE_NF_EBTABLES dependent on BRIDGE and NETFILTER:
warning: (NF_TABLES_BRIDGE && BRIDGE_NF_EBTABLES) selects
BRIDGE_NETFILTER which has unmet direct dependencies (NET && BRIDGE &&
NETFILTER && INET && NETFILTER_ADVANCED)
net/built-in.o: In function `br_parse_ip_options':
br_netfilter.c:(.text+0x4a5ba): undefined reference to `ip_options_compile'
br_netfilter.c:(.text+0x4a5ed): undefined reference to `ip_options_rcv_srr'
net/built-in.o: In function `br_nf_pre_routing_finish':
br_netfilter.c:(.text+0x4a8a4): undefined reference to `ip_route_input_noref'
br_netfilter.c:(.text+0x4a987): undefined reference to `ip_route_output_flow'
make: *** [vmlinux] Error 1
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Receiving a ICMP response to an IPIP packet in a non-linear skb could
cause a kernel panic in __skb_pull.
The problem was introduced in
commit f2edb9f770 ("ipvs: implement
passive PMTUD for IPIP packets").
Signed-off-by: Peter Christensen <pch@ordbogen.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
This change adds some entropy to polling cycles, choosing the next
polling rf technology randomly. This reflects the change done in the
pn533 driver, avoiding possible infinite loop for devices that export 2
targets on 2 different modulations. If the first target is not
readable, we will stay in an error loop for ever.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The error code returned by digital_in_send_cmd() was not returned by
digital_in_send_atr_req().
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As it may then take longer than what the user specified using
setsockopt(SO_RCVTIMEO).
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-05-23
I have two more fixes intended for the 3.15 stream...
For the iwlwifi one, Emmanuel says:
"A race has been discovered in the beacon filtering code. Since the
fix is too big for 3.15, I disable here the feature."
For the bluetooth one, Gustavo says:
"This pull request contains a very important fix for 3.15. Here we fix the
permissions of a debugfs file that would otherwise allow unauthorized users
to write content to it."
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"It looks like a sizeble collection but this is nearly 3 weeks of bug
fixing while you were away.
1) Fix crashes over IPSEC tunnels with NAT, the latter can reroute
the packet through a non-IPSEC protected path and the code has to
be able to handle SKBs attached to routes lacking an attached xfrm
state. From Steffen Klassert.
2) Fix OOPSs in ipv4 and ipv6 ipsec layers for unsupported
sub-protocols, also from Steffen Klassert.
3) Set local_df on fragmented netfilter skbs otherwise we won't be
able to forward successfully, from Florian Westphal.
4) cdc_mbim ipv6 neighbour code does __vlan_find_dev_deep without
holding RCU lock, from Bjorn Mork.
5) local_df test in ip_may_fragment is inverted, from Florian
Westphal.
6) jme driver doesn't check for DMA mapping failures, from Neil
Horman.
7) qlogic driver doesn't calculate number of TX queues properly, from
Shahed Shaikh.
8) fib_info_cnt can drift irreversibly positive if we fail to
allocate the fi->fib_metrics array, from Sergey Popovich.
9) Fix use after free in ip6_route_me_harder(), also from Sergey
Popovich.
10) When SYSCTL is disabled, we don't handle local_port_range and
ping_group_range defaults properly at all, from Cong Wang.
11) Unaccelerated VLAN tagged frames improperly handled by cdc_mbim
driver, fix from Bjorn Mork.
12) cassini driver needs nested lock annotations for TX locking, from
Emil Goode.
13) On init error ipv6 VTI driver can unregister pernet ops twice,
oops. Fix from Mahtias Krause.
14) If macvlan device is down, don't propagate IFF_ALLMULTI changes,
from Peter Christensen.
15) Missing NULL pointer check while parsing netlink config options in
ip6_tnl_validate(). From Susant Sahani.
16) Fix handling of neighbour entries during ipv6 router reachability
probing, from Duan Jiong.
17) x86 and s390 JIT address randomization has some address
calculation bugs leading to crashes, from Alexei Starovoitov and
Heiko Carstens.
18) Clear up those uglies with nop patching and net_get_random_once(),
from Hannes Frederic Sowa.
19) Option length miscalculated in ip6_append_data(), fix also from
Hannes Frederic Sowa.
20) A while ago we fixed a race during device unregistry when a
namespace went down, turns out there is a second place that needs
similar protection. From Cong Wang.
21) In the new Altera TSE driver multicast filtering isn't working,
disable it and just use promisc mode until the cause is found.
From Vince Bridgers.
22) When we disable router enabling in ipv6 we have to flush the
cached routes explicitly, from Duan Jiong.
23) NBMA tunnels should not cache routes on the tunnel object because
the key is variable, from Timo Teräs.
24) With stacked devices GRO information in skb->cb[] can be not setup
properly, make sure it is in all code paths. From Eric Dumazet.
25) Really fix stacked vlan locking, multiple levels of nesting with
intervening non-vlan devices are possible. From Vlad Yasevich.
26) Fallback ipip tunnel device's mtu is not setup properly, from
Steffen Klassert.
27) The packet scheduler's tcindex filter can crash because we
structure copy objects with list_head's inside, oops. From Cong
Wang.
28) Fix CHECKSUM_COMPLETE handling for ipv6 GRE tunnels, from Eric
Dumazet.
29) In some configurations 'itag' in __mkroute_input() can end up
being used uninitialized because of how fib_validate_source()
works. Fix it by explitly initializing itag to zero like all the
other fib_validate_source() callers do, from Li RongQing"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
batman: fix a bogus warning from batadv_is_on_batman_iface()
ipv4: initialise the itag variable in __mkroute_input
bonding: Send ALB learning packets using the right source
bonding: Don't assume 802.1Q when sending alb learning packets.
net: doc: Update references to skb->rxhash
stmmac: Remove unbalanced clk_disable call
ipv6: gro: fix CHECKSUM_COMPLETE support
net_sched: fix an oops in tcindex filter
can: peak_pci: prevent use after free at netdev removal
ip_tunnel: Initialize the fallback device properly
vlan: Fix build error wth vlan_get_encap_level()
can: c_can: remove obsolete STRICT_FRAME_ORDERING Kconfig option
MAINTAINERS: Pravin Shelar is Open vSwitch maintainer.
bnx2x: Convert return 0 to return rc
bonding: Fix alb mode to only use first level vlans.
bonding: Fix stacked device detection in arp monitoring
macvlan: Fix lockdep warnings with stacked macvlan devices
vlan: Fix lockdep warning with stacked vlan devices.
net: Allow for more then a single subclass for netif_addr_lock
net: Find the nesting level of a given device by type.
...
The sk_unattached_filter_create() API is used by BPF filters that
are not directly attached or related to sockets, and are used in
team, ptp, xt_bpf, cls_bpf, etc. As such all users do their own
internal managment of obtaining filter blocks and thus already
have them in kernel memory and set up before calling into
sk_unattached_filter_create(). As a result, due to __user annotation
in sock_fprog, sparse triggers false positives (incorrect type in
assignment [different address space]) when filters are set up before
passing them to sk_unattached_filter_create(). Therefore, let
sk_unattached_filter_create() API use sock_fprog_kern to overcome
this issue.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lets get rid of this macro. After commit 5bcfedf06f ("net: filter:
simplify label names from jump-table"), labels have become more
readable due to omission of BPF_ prefix but at the same time more
generic, so that things like `git grep -n` would not find them. As
a middle path, lets get rid of the DL macro as it's not strictly
needed and would otherwise just hide the full name.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added new L2TP configuration options to allow TX and RX of
zero checksums in IPv6. Default is not to use them.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 6935 permits zero checksums to be used in IPv6 however this is
recommended only for certain tunnel protocols, it does not make
checksums completely optional like they are in IPv4.
This patch restricts the use of IPv6 zero checksums that was previously
intoduced. no_check6_tx and no_check6_rx have been added to control
the use of checksums in UDP6 RX and TX path. The normal
sk_no_check_{rx,tx} settings are not used (this avoids ambiguity when
dealing with a dual stack socket).
A helper function has been added (udp_set_no_check6) which can be
called by tunnel impelmentations to all zero checksums (send on the
socket, and accept them as valid).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define separate fields in the sock structure for configuring disabling
checksums in both TX and RX-- sk_no_check_tx and sk_no_check_rx.
The SO_NO_CHECK socket option only affects sk_no_check_tx. Also,
removed UDP_CSUM_* defines since they are no longer necessary.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't seem like an protocols are setting anything other
than the default, and allowing to arbitrarily disable checksums
for a whole protocol seems dangerous. This can be done on a per
socket basis.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting sk_no_check to UDP_CSUM_NORCV seems to have no effect.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o min_tx_rate puts lower limit on the VF bandwidth. VF is guaranteed
to have a bandwidth of at least this value.
max_tx_rate puts cap on the VF bandwidth. VF can have a bandwidth
of up to this value.
o A new handler set_vf_rate for attr IFLA_VF_RATE has been introduced
which takes 4 arguments:
netdev, VF number, min_tx_rate, max_tx_rate
o ndo_set_vf_rate replaces ndo_set_vf_tx_rate handler.
o Drivers that currently implement ndo_set_vf_tx_rate should now call
ndo_set_vf_rate instead and reject attempt to set a minimum bandwidth
greater than 0 for IFLA_VF_TX_RATE when IFLA_VF_RATE is not yet
implemented by driver.
o If user enters only one of either min_tx_rate or max_tx_rate, then,
userland should read back the other value from driver and set both
for IFLA_VF_RATE.
Drivers that have not yet implemented IFLA_VF_RATE should always
return min_tx_rate as 0 when read from ip tool.
o If both IFLA_VF_TX_RATE and IFLA_VF_RATE options are specified, then
IFLA_VF_RATE should override.
o Idea is to have consistent display of rate values to user.
o Usage example: -
./ip link set p4p1 vf 0 rate 900
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 900 (Mbps), max_tx_rate 900Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
./ip link set p4p1 vf 0 max_tx_rate 300 min_tx_rate 200
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 300 (Mbps), max_tx_rate 300Mbps,
min_tx_rate 200Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
./ip link set p4p1 vf 0 max_tx_rate 600 rate 300
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5, tx rate 600 (Mbps), max_tx_rate 600Mbps,
min_tx_rate 200Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the mgmt level we have a key type parameter which currently accepts
two possible values: 0x00 for unauthenticated and 0x01 for
authenticated. However, in the internal struct smp_ltk representation we
have an explicit "authenticated" boolean value.
To make this distinction clear, add defines for the possible mgmt values
and do conversion to and from the internal authenticated value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Following patch get rid of struct genl_family_and_ops which is
redundant due to changes to struct genl_family.
Signed-off-by: Kyle Mestery <mestery@noironetworks.com>
Acked-by: Kyle Mestery <mestery@noironetworks.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Following patch will be easier to reason about with separate
ovs_flow_cmd_new() and ovs_flow_cmd_set() functions.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
ovs_flow_cmd_del() now allocates reply (if needed) after the flow has
already been removed from the flow table. If the reply allocation
fails, a netlink error is signaled with netlink_set_err(), as is
already done in ovs_flow_cmd_new_or_set() in the similar situation.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reduce and clarify locking requirements for ovs_flow_cmd_alloc_info(),
ovs_flow_cmd_fill_info() and ovs_flow_cmd_build_info().
A datapath pointer is available only when holding a lock. Change
ovs_flow_cmd_fill_info() and ovs_flow_cmd_build_info() to take a
dp_ifindex directly, rather than a datapath pointer that is then
(only) used to get the dp_ifindex. This is useful, since the
dp_ifindex is available even when the datapath pointer is not, both
before and after taking a lock, which makes further critical section
reduction possible.
Make ovs_flow_cmd_alloc_info() take an 'acts' argument instead a
'flow' pointer. This allows some future patches to do the allocation
before acquiring the flow pointer.
The locking requirements after this patch are:
ovs_flow_cmd_alloc_info(): May be called without locking, must not be
called while holding the RCU read lock (due to memory allocation).
If 'acts' belong to a flow in the flow table, however, then the
caller must hold ovs_mutex.
ovs_flow_cmd_fill_info(): Either ovs_mutex or RCU read lock must be held.
ovs_flow_cmd_build_info(): This calls both of the above, so the caller
must hold ovs_mutex.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
For ovs_flow_stats_get() using ovsl_dereference() was wrong, since
flow dumps call this with RCU read lock.
ovs_flow_stats_clear() is always called with ovs_mutex, so can use
ovsl_dereference().
Also, make the ovs_flow_stats_get() 'flow' argument const to make
later patches cleaner.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Incorrect struct name was confusing, even though otherwise
inconsequental.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Move most memory allocations away from the ovs_mutex critical
sections. vport allocations still happen while the lock is taken, as
changing that would require major refactoring. Also, vports are
created very rarely so it should not matter.
Change ovs_dp_cmd_get() now only takes the rcu_read_lock(), rather
than ovs_lock(), as nothing need to be changed. This was done by
ovs_vport_cmd_get() already.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Masks are inserted when flows are inserted to the table, so it is
logical to correspondingly remove masks when flows are removed from
the table, in ovs_flow_table_remove().
This allows ovs_flow_free() to be called without locking, which will
be used by later patches.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
