the check of the return code is missing, user space does not get notified
about the error condition:
omapdss OVERLAY error: overlay 2 horizontally not inside the display area (403 + 800 >= 800)
omapdss APPLY error: failed to apply settings: illegal configuration.
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support for DRA7xx DPI output.
DRA7xx has three DPI outputs, each of which gets its input from a DISPC
channel. However, DRA72x has only one video PLL, and DRA74x has two
video PLLs. In both cases the video PLLs need to be shared between
multiple outputs. The driver doesn't handle this at the moment.
Also, DRA7xx requires configuring CONTROL module bits to route the clock
from the PLL to the used DISPC channel.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support for DRA7xx to the HDMI driver.
The HDMI block on DRA7xx is the same as on OMAP5, except we need to
enable and disable the HDMI PLL via the CONTROL module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On DRA7xx, DISPC needs to write output signal polarities not only to a
DISPC register, like for all earlier DSS versions, but to control
module's CTRL_CORE_SMA_SW_1 register.
This patch adds support to write the polarities to control module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add DRA7xx support to DISPC driver. The DISPC block is the same as on
OMAP5, except the PLL's used for clocking are "videoX", not "dsiX".
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DRA7xx SoCs have one (DRA72x) or two (DRA74x) video PLLs. They are
basically the same as DSI PLLs on OMAPs, but without the rest of the DSI
hardware. The video PLLs also require some configuration via the CONTROL
module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add functions which configure the control module register
CTRL_CORE_DSS_PLL_CONTROL found in DRA7xx SoCs. This register configures
whether the PLL registers are accessed internally by DSS, or externally
using OCP2SCP interface. They also configure muxes which route the PLL
output to a particular LCD overlay manager within DSS.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A race issue has been observed with the encoder-tpd12s015 driver, which
leads to errors when trying to read EDID. This has only now been
observed, as OMAP4 and OMAP5 boards used SoC's GPIOs for LS_OE GPIO. On
dra7-evm boards, the LS_OE is behind a i2c controlled GPIO expander,
which increases the time to set the LS_OE.
This patch simplifies the handling of the LS_OE gpio in the driver by
removing the interrupt handling totally. The only time we actually need
to enable LS_OE is when we are reading the EDID, and thus we can just
set and clear the LS_OE gpio inside the read_edid() function.
This also has the additional benefit of very slightly decreasing the
power consumption.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The OMAP5 HW supports directing DIGIT channel to DPI output, but the
driver doesn't support that. However, we have marked that configuration
as possible in the dss features, so in certain cases the driver tries to
use that configuration, leading to broken display.
Fix the problem by allowing DIGIT channel to go only to HDMI output.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In some cases we need global identifiers for the DSS PLLs, for example
when configuring clock muxing on DRA7. For this purpose let's add a
'enum dss_pll_id'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The sys_copyarea() function performs the same operation as
cfb_copyarea() but using normal memory access instead of I/O
accessors. Since the introduction of sys_copyarea(), there
have been two fixes to cfb_copyarea():
- 00a9d699 ("framebuffer: fix cfb_copyarea")
- 5b789da8 ("framebuffer: fix screen corruption when copying")
This patch incorporates the fixes into sys_copyarea() as well.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The frame buffer core can be a module, which means any fb drivers
should be able to build as modules too. This turns mmpfb into
a tristate option to allow that and fix a possible randconfig
build error.
drivers/built-in.o: In function `modes_setup':
:(.text+0x11b34): undefined reference to `fb_videomode_to_modelist'
:(.text+0x11b5c): undefined reference to `fb_videomode_to_var'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Device driver should not directly select subsystems. In this case
we get build warnings like
warning: (ARCH_REQUIRE_GPIOLIB && PINCTRL_AT91 && PINCTRL_NOMADIK && MFD_TC6393XB && FB_VIA) selects GPIOLIB which has unmet direct dependencies (ARCH_WANT_OPTIONAL_GPIOLIB || ARCH_REQUIRE_GPIOLIB)
which we can avoid using the normal 'depends on' statement.
Also, this patch makes it possible for DRM drivers to have a dependency
on GPIOLIB without getting circular Kconfig dependencies.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
this patch fixes ssd1307fb_ssd1306_init() function to return
proper error codes in case of failures.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As per the suggestion of Thierry Reding rename
HDMI_AUDIO_CODING_TYPE_EXT_STREAM to HDMI_AUDIO_CODING_TYPE_EXT_CT to
be consistent with the CEA-861 spec.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When receiving video it is very useful to be able to unpack the InfoFrames.
Logging is useful as well, both for transmitters and receivers.
Especially when implementing the VIDIOC_LOG_STATUS ioctl (supported by many
V4L2 drivers) for a receiver it is important to be able to easily log what
the InfoFrame contains. This greatly simplifies debugging.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
CVT v1.1 spec says: "the vertical front porch shall in all cases be
fixed to 3 lines". The code in fbcvt.c instead sets the _back_ porch to
3 (plus margin).
After swapping cvt.v_front_porch and cvt.v_back_porch the resulting
timings were in line with CVT timings in VESA DMT spec.
The bug seems to be more than 9 years old, but I presume it has not been
noticed as usually the video timings come from the EDID or from the
timing tables in fbdev, and probably swapped values for vfp and vbp work
fine for most of the displays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: David Ung <davidu@nvidia.com>
Cc: Antonino A. Daplas <adaplas@gmail.com>
var->yoffset is of the type __u32, hence the comparison will always
be false.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use NULL instead of 0 for the last entry of dmt_modes struct.
Supresses "sparse: Using plain integer as NULL pointer" warning.
Signed-off-by: David Ung <davidu@nvidia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
IRQ_TYPE_PRIO is no longer used by the Atari platform interrupt code
since commit 734085651c ("[PATCH] m68k: convert atari irq code")
in v2.6.18-rc1, so drop it.
Note that its value has been reused for a different purpose
(IRQ_TYPE_EDGE_FALLING) since commit 6a6de9ef58 ("[PATCH] genirq:
core") in v2.6.18-rc1.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
fbmon may generate mode timings that are out of spec of the monitor.
eg DELL U2410 has a max clock 170mhz but advertises a resolutions of
1920x1200@60 in its Standard Timings using 2byte code of D1 00.
When this is looked up in the DMT table it gives it a 193mhz clock.
Although the DELL monitor supports 1920x1200@60, it can only run with
reduced timings at 154mhz or DMT id 0x44 which has no STD 2byte code.
This patch checks to see if the mode can be supported by the monitor
by comparing against monspecs.dclkmax.
Signed-off-by: David Ung <davidu@nvidia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add the VESA Display Monitor Timing (DMT) table.
During parsing of Standard Timings, it compare the 2 byte STD code
with DMT to see what the VESA mode should be. If there is no entry
in the vesa_modes table or no match found, it fallsback to the
GTF timings.
Signed-off-by: David Ung <davidu@nvidia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
this patch sets the default height if its not found in DT.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
this patch drops the unused function ssd1307fb_write_data().
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
commit 765d5b9c2b ("fbdev: fbcon: select
VT_HW_CONSOLE_BINDING") made FRAMEBUFFER_CONSOLE always select
VT_HW_CONSOLE_BINDING, but forgot to remove
select VT_HW_CONSOLE_BINDING if FRAMEBUFFER_CONSOLE
from the individual drivers' sections that already did this before.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
static code analysis from cppcheck reports:
[drivers/video/fbdev/broadsheetfb.c:673]:
(error) Memory leak: sector_buffer
sector_buffer is not being kfree'd on each call to
broadsheet_spiflash_rewrite_sector(), so free it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
PA-RISC already handled the dummy console screen size selection in
Kconfig, so generalize this to other platforms.
ARM keeps on using screen_info, which is filled in by
platform-specific code, or from ATAGS.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
continue is not needed at the end of a for loop, also removed the
braces which were no longer required.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
vga_in8() was storing the return value in tmp, but that return value
was never used again. so it should be safe to remove those variables.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
the check for info is not required as we are checking it immediately
after gxfb_init_fbinfo() and lxfb_init_fbinfo() and returnig -ENOMEM
if it is NULL.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Assigning ddata->invert_polarity to itself is not very useful; the
context suggests that the right-hand side should have been
pdata->invert_polarity.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
of_platform_device_create is only defined when CONFIG_OF_ADDRESS is set,
which is normally always the case when CONFIG_OF is defined, except on Sparc,
so explicitly check for CONFIG_OF_ADDRESS rather then for CONFIG_OF.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When allocate framebuffer memory using dma_alloc_coherent(),
we'd better use dma_addr_t instead of phys_addr_t. Because the
address we got in fact is DMA or bus address for the platform.
This patch also fixes below build warning:
drivers/video/fbdev/ocfb.c:335:2:
warning: passing argument 3 of ‘dma_alloc_attrs’
from incompatible pointer type [enabled by default]
Signed-off-by: Qiang Chen <qiang2.chen@sonymobile.com>
Acked-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
opa362 is amplifier for video and can be connected to the tvout pads
of the OMAP3. It has one gpio control for enable/disable of the output
(high impedance).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
the check for info is not required as we are checking it immediately
after gx1fb_init_fbinfo() and returnig -ENOMEM if it is NULL.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We can mark the DMI system id table as __initconst by using a helper
variable that'll tell us if we need to unregister the reboot notifier in
atyfb_exit() instead of matching the DMI system id again.
This frees up ~680 bytes of runtime memory, the DMI table occupies.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
After the commit ef691ff48b (OMAPDSS: DT: Get source endpoint by
matching reg-id) we look for the SDI output using the port number.
However, the SDI driver doesn't set the port number, which causes the
SDI display to not initialize.
Fix this by setting the SDI port number to 1. We use a hardcoded value,
as SDI was used only on OMAP3 and it's always port number 1 there.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
fb_deferred_io_fsync() returns the value of schedule_delayed_work() as
an error code, but schedule_delayed_work() does not return an error. It
returns true/false depending on whether the work was already queued.
Fix this by ignoring the return value of schedule_delayed_work().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: stable@vger.kernel.org
If the probe of an fb driver has been deferred due to missing
dependencies, and the probe is later ran when a module is loaded, the
fbdev framework will try to find a logo to use.
However, the logos are __initdata, and have already been freed. This
causes sometimes page faults, if the logo memory is not mapped,
sometimes other random crashes as the logo data is invalid, and
sometimes nothing, if the fbdev decides to reject the logo (e.g. the
random value depicting the logo's height is too big).
This patch adds a late_initcall function to mark the logos as freed. In
reality the logos are freed later, and fbdev probe may be ran between
this late_initcall and the freeing of the logos. In that case we will
miss drawing the logo, even if it would be possible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: stable@vger.kernel.org
The regulator_disable() doesn't accept NULL pointers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
HDMI hardware parameters structs for OMAP4 and OMAP5 contained two
initializers for 'clkdco_max'. The first one was a remnant with wrong
value.
Remove the extra initializer entries.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
The alternative of CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME may be
replaced with CONFIG_PM too.
Make these changes in 2 files under drivers/video/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Pull ARM updates from Russell King:
"The major updates included in this update are:
- Clang compatible stack pointer accesses by Behan Webster.
- SA11x0 updates from Dmitry Eremin-Solenikov.
- kgdb handling of breakpoints with read-only text/modules
- Support for Privileged-no-execute feature on ARMv7 to prevent
userspace code execution by the kernel.
- AMBA primecell bus handling of irq-safe runtime PM
- Unwinding support for memset/memzero/memmove/memcpy functions
- VFP fixes for Krait CPUs and improvements in detecting the VFP
architecture
- A number of code cleanups (using pr_*, removing or reducing the
severity of a couple of kernel messages, splitting ftrace asm code
out to a separate file, etc.)
- Add machine name to stack dump output"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (62 commits)
ARM: 8247/2: pcmcia: sa1100: make use of device clock
ARM: 8246/2: pcmcia: sa1111: provide device clock
ARM: 8245/1: pcmcia: soc-common: enable/disable socket clocks
ARM: 8244/1: fbdev: sa1100fb: make use of device clock
ARM: 8243/1: sa1100: add a clock alias for sa1111 pcmcia device
ARM: 8242/1: sa1100: add cpu clock
ARM: 8221/1: PJ4: allow building in Thumb-2 mode
ARM: 8234/1: sa1100: reorder IRQ handling code
ARM: 8233/1: sa1100: switch to hwirq usage
ARM: 8232/1: sa1100: merge GPIO multiplexer IRQ to "normal" irq domain
ARM: 8231/1: sa1100: introduce irqdomains support
ARM: 8230/1: sa1100: shift IRQs by one
ARM: 8229/1: sa1100: replace irq numbers with names in irq driver
ARM: 8228/1: sa1100: drop entry-macro.S
ARM: 8227/1: sa1100: switch to MULTI_IRQ_HANDLER
ARM: 8241/1: Update processor_modes for hyp and monitor mode
ARM: 8240/1: MCPM: document mcpm_sync_init()
ARM: 8239/1: Introduce {set,clear}_pte_bit
ARM: 8238/1: mm: Refine set_memory_* functions
ARM: 8237/1: fix flush_pfn_alias
...
* support for mx6sl and mx6sx
* OMAP HDMI audio rewrite to make it finally work
* OMAP video PLL work to prepare for new DRA7xx SoCs
* simplefb DT related improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VAZB
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
- support for mx6sl and mx6sx
- OMAP HDMI audio rewrite to make it finally work
- OMAP video PLL work to prepare for new DRA7xx SoCs
- simplefb DT related improvements
* tag 'fbdev-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (81 commits)
video: uvesafb: Deletion of an unnecessary check before the function call "platform_device_put"
video: fbdev-VIA: Deletion of an unnecessary check before the function call "framebuffer_release"
video: fbdev-MMP: Deletion of an unnecessary check before the function call "mmp_unregister_path"
video: mx3fb: Deletion of an unnecessary check before the function call "backlight_device_unregister"
video: fbdev-OMAP2: Deletion of unnecessary checks before the function call "i2c_put_adapter"
video: fbdev-SIS: Deletion of unnecessary checks before the function call "pci_dev_put"
video: smscufx: Deletion of unnecessary checks before the function call "vfree"
video: udlfb: Deletion of unnecessary checks before the function call "vfree"
video: uvesafb: Deletion of an unnecessary check before the function call "uvesafb_free"
video: fbdev-LCDC: Deletion of an unnecessary check before the function call "vfree"
video: fbdev: arkfb: suppress build warning
video: fbdev: s3fb: suppress build warning
video: fbdev: vt8623fb: suppress build warning
OMAPDSS: hdmi5: Fix bit field for IEC958_AES2_CON_SOURCE
OMAPDSS: hdmi: Remove __exit qualifier from hdmi_uninit_output()
OMAPDSS: hdmi5: Change hdmi_wp idlemode to to no_idle for audio playback
OMAPDSS: Remove all references to obsolete HDMI audio callbacks
ASoC: omap: Remove obsolete HDMI audio code and Kconfig options
OMAPDSS: hdmi5: Register ASoC platform device for omap hdmi audio
OMAPDSS: hdmi5: Remove callbacks for the old ASoC DAI driver
...
- Simplify Device Tree initialisation; lp855x_bl
- Add Regulator support; lp855x
- Remove Bryan from the Maintainer list -- new baby, no time :)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0PNI
-----END PGP SIGNATURE-----
Merge tag 'backlight-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
- Clean-up leaky resources; pwm_bl
- Simplify Device Tree initialisation; lp855x_bl
- Add Regulator support; lp855x
- Remove Bryan from the Maintainer list -- new baby, no time :)
* tag 'backlight-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
MAINTAINERS: Remove my name from Backlight subsystem
backlight: lp855x: Add supply regulator to lp855x
backlight: lp855x: Refactor DT parsing code
backlight: pwm: Clean-up pwm requested using legacy API
Pull x86 mm tree changes from Ingo Molnar:
"The biggest change is full PAT support from Jürgen Gross:
The x86 architecture offers via the PAT (Page Attribute Table) a
way to specify different caching modes in page table entries. The
PAT MSR contains 8 entries each specifying one of 6 possible cache
modes. A pte references one of those entries via 3 bits:
_PAGE_PAT, _PAGE_PWT and _PAGE_PCD.
The Linux kernel currently supports only 4 different cache modes.
The PAT MSR is set up in a way that the setting of _PAGE_PAT in a
pte doesn't matter: the top 4 entries in the PAT MSR are the same
as the 4 lower entries.
This results in the kernel not supporting e.g. write-through mode.
Especially this cache mode would speed up drivers of video cards
which now have to use uncached accesses.
OTOH some old processors (Pentium) don't support PAT correctly and
the Xen hypervisor has been using a different PAT MSR configuration
for some time now and can't change that as this setting is part of
the ABI.
This patch set abstracts the cache mode from the pte and introduces
tables to translate between cache mode and pte bits (the default
cache mode "write back" is hard-wired to PAT entry 0). The tables
are statically initialized with values being compatible to old
processors and current usage. As soon as the PAT MSR is changed
(or - in case of Xen - is read at boot time) the tables are changed
accordingly. Requests of mappings with special cache modes are
always possible now, in case they are not supported there will be a
fallback to a compatible but slower mode.
Summing it up, this patch set adds the following features:
- capability to support WT and WP cache modes on processors with
full PAT support
- processors with no or uncorrect PAT support are still working as
today, even if WT or WP cache mode are selected by drivers for
some pages
- reduction of Xen special handling regarding cache mode
Another change is a boot speedup on ridiculously large RAM systems,
plus other smaller fixes"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
x86: mm: Move PAT only functions to mm/pat.c
xen: Support Xen pv-domains using PAT
x86: Enable PAT to use cache mode translation tables
x86: Respect PAT bit when copying pte values between large and normal pages
x86: Support PAT bit in pagetable dump for lower levels
x86: Clean up pgtable_types.h
x86: Use new cache mode type in memtype related functions
x86: Use new cache mode type in mm/ioremap.c
x86: Use new cache mode type in setting page attributes
x86: Remove looking for setting of _PAGE_PAT_LARGE in pageattr.c
x86: Use new cache mode type in track_pfn_remap() and track_pfn_insert()
x86: Use new cache mode type in mm/iomap_32.c
x86: Use new cache mode type in asm/pgtable.h
x86: Use new cache mode type in arch/x86/mm/init_64.c
x86: Use new cache mode type in arch/x86/pci
x86: Use new cache mode type in drivers/video/fbdev/vermilion
x86: Use new cache mode type in drivers/video/fbdev/gbefb.c
x86: Use new cache mode type in include/asm/fb.h
x86: Make page cache mode a real type
x86: mm: Use 2GB memory block size on large-memory x86-64 systems
...
On Atmel AT91, the conversion to device tree is now considered complete,
and all machines that were not already converted in 3.18 are assumed to
be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the platform
itself is not "multiplatform"-enabled, but both issues are going to be
taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size
of the branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iD8DBQBUhyNX5t5GS2LDRf4RAnjxAKCER7eoLNadu1/93n/a9d1nUz4MoQCcCZUq
BolxCOi0wr4YTcQtp7rHzWI=
=ykAB
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup on mach-at91 from Arnd Bergmann:
"On Atmel AT91, the conversion to device tree is now considered
complete, and all machines that were not already converted in 3.18 are
assumed to be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the
platform itself is not "multiplatform"-enabled, but both issues are
going to be taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size of
the branch"
* tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: at91: remove unused board.h file
ARM: at91: remove unneeded header files
ARM: at91/clocksource: remove !DT PIT initializations
ARM: at91: at91rm9200 ST initialization is now DT only
ARM: at91: remove old AT91-specific drivers
ARM: at91: cleanup initilisation code by removing dead code
ARM: at91/Kconfig: select board files automatically
ARM: at91: remove unused IRQ function declarations
ARM: at91: remove legacy IRQ driver and related code
ARM: at91: remove old at91-specific clock driver
ARM: at91: remove clock data in at91sam9n12.c and at91sam9x5.c files
ARM: at91: remove all !DT related configuration options
ARM: at91/trivial: update Kconfig comment to mention SAMA5
ARM: at91: always USE_OF from now on
ARM: at91/Kconfig: remove ARCH_AT91RM9200 option for drivers
ARM: at91: switch configuration option to SOC_AT91RM9200
ARM: at91: remove at91rm9200 legacy board support
ARM: at91: remove at91rm9200 legacy boards files
ARM: at91/Kconfig: remove useless fbdev Kconfig options
ARM: at91: remove at91sam9261/at91sam9g10 legacy board support
...
This patch adds a supply regulator to the lp855x platform data to facilitate
powering on/off the 3V rail attached to the controller.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Milo Kim <milo.kim@ti.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch refactors the dt parsing code to avoid setting platform_data,
instead just setting lp->pdata directly. This facilitates easier
probe deferral since the current scheme would require us to clear out
dev->platform_data before deferring.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Milo Kim <milo.kim@ti.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use per-device clock (instead of calling cpufreq_get(0), which can
return 0 if no cpu frequency driver is selected) to program timings.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The platform_device_put() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The framebuffer_release() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The mmp_unregister_path() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The backlight_device_unregister() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The i2c_put_adapter() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The pci_dev_put() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call
is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The vfree() function performs also input parameter validation. Thus the test
around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The vfree() function performs also input parameter validation. Thus the test
around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The uvesafb_free() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The vfree() function performs also input parameter validation.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
this patch fixes following build warning:
drivers/video/fbdev/arkfb.c: In function ‘ark_pci_probe’:
drivers/video/fbdev/arkfb.c:1019:23: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
par->state.vgabase = (void __iomem *) vga_res.start;
^
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
this patch fixes following build warning:
drivers/video/fbdev/s3fb.c: In function ‘s3_pci_probe’:
drivers/video/fbdev/s3fb.c:1185:23: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
par->state.vgabase = (void __iomem *) vga_res.start;
^
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
this patch fixes following build warning:
drivers/video/fbdev/vt8623fb.c: In function ‘vt8623_pci_probe’:
drivers/video/fbdev/vt8623fb.c:734:23: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
par->state.vgabase = (void __iomem *) vga_res.start;
^
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The bit field for IEC958_AES2_CON_SOURCE is bits 3-0 in
HDMI_CORE_FC_AUDSCHNLS2, not imaginary bits 3-4 (reverse order).
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove __exit qualifier from hdmi_uninit_output() because it is used
also in omapdss_hdmihw_probe().
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Enabling idle mode during audio playback causes the glitches on OMAP5
HDMI. The TRM also suggests to use no-idle for HDMI audio playback.
This patch sets HDMI idle mode to no-idle for the duration of the
playback, and restores it back to original value afterwards.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In new model these callbacks are obsolete since the ASoC component
drivers are integrated into the HDMI drivers and no callbacks are
needed anymore.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Implements callbacks for OMAP HDMI audio platform driver and registers
it in probe function. Unregistering is done in remove function.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Removes the OMAP5 HDMI audio callbacks for the old external DAI driver.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Implements callbacks for OMAP HDMI audio platform driver and registers
it in probe function. Unregistering is done in remove function.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Removes the OMAP4 HDMI audio callbacks for the old external DAI driver.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Make hdmi_mode_has_audio() more user friedly by taking hdmi_config as
parameter.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The booleans are not used anymore. Just select SND_OMAP_SOC_HDMI_AUDIO
to enable OMAP HDMI audio support.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adds display_enabled flag and audio_abort_cb callback to struct hdmi.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This is used to store omap-hdmi-audio pdev for unregistering it.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Unify the private anonymous struct in hdmi4.c and hdmi5.c, name it as
struct omap_hdmi, and make it public in hdmi.h.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The audio dma port is found in the hdmi_wp physical address space.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It does not waste too many bytes to compile all audio related core
functions always in with HDMI support. It should help readability and
in keeping the audio code in working shape. Leave the options just for
disabling and enabling the functionality in hdmi[45].c.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The OMAP5 HDMI audio implementation needs HDMI_AUDIO_LAYOUT_6CH in
hdmi_core_audio_layout enum. I found the correct value from ti-linux
3.8 tree.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The hdmi_wp_audio_config_format() expects sample_order of struct
hdmi_audio_format to be initialized. The only allowed value is
HDMI_AUDIO_SAMPLE_LEFT_FIRST.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Only OMAP4 DSS has non reserved bits above 6th bit in HDMI_WP_AUDIO_CFG.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Both CONFIG_OF and CONFIG_COMMON_CLK must be defined to be able to use of
clocks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A word was corrected in the description for a parameter of
the mmp_unregister_path() function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Two mistyped words were corrected in the description for
the mmp_unregister_path() function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove Kconfig options used nowhere.
The removal of CONFIG_ARCH_AT91SAM9261 option allowed to spot this oddness.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch fixes duplicated include dma-mapping.h in
drivers/video/fbdev/amba-clcd.c
Signed-off-by: Qiang Chen <qiang2.chen@sonymobile.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When removing old board !DT support, several Kconfig options were deleted.
Propagate this removal to drivers Kconfig files.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
