The kernel provides a "/proc/sys/net/ipv6/conf/<iface>/mtu"
file, which can temporarily record the mtu value of the last
received RA message when the RA mtu value is lower than the
interface mtu, but this proc has following limitations:
(1) when the interface mtu (/sys/class/net/<iface>/mtu) is
updeated, mtu6 (/proc/sys/net/ipv6/conf/<iface>/mtu) will
be updated to the value of interface mtu;
(2) mtu6 (/proc/sys/net/ipv6/conf/<iface>/mtu) only affect
ipv6 connection, and not affect ipv4.
Therefore, when the mtu option is carried in the RA message,
there will be a problem that the user sometimes cannot obtain
RA mtu value correctly by reading mtu6.
After this patch set, if a RA message carries the mtu option,
you can send a netlink msg which nlmsg_type is RTM_GETLINK,
and then by parsing the attribute of IFLA_INET6_RA_MTU to
get the mtu value carried in the RA message received on the
inet6 device. In addition, you can also get a link notification
when ra_mtu is updated so it doesn't have to poll.
In this way, if the MTU values that the device receives from
the network in the PCO IPv4 and the RA IPv6 procedures are
different, the user can obtain the correct ipv6 ra_mtu value
and compare the value of ra_mtu and ipv4 mtu, then the device
can use the lower MTU value for both IPv4 and IPv6.
Signed-off-by: Rocco Yue <rocco.yue@mediatek.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20210827150412.9267-1-rocco.yue@mediatek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace IP6_SFLSIZE() with struct_size() helper in order to avoid any
potential type mistakes or integer overflows that, in the worst
scenario, could lead to heap overflows.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of this lock is to avoid a bottleneck in the query/report
event handler logic.
By previous patches, almost all mld data is protected by RTNL.
So, the query and report event handler, which is data path logic
acquires RTNL too. Therefore if a lot of query and report events
are received, it uses RTNL for a long time.
So it makes the control-plane bottleneck because of using RTNL.
In order to avoid this bottleneck, mc_lock is added.
mc_lock protect only per-interface mld data and per-interface mld
data is used in the query/report event handler logic.
So, no longer rtnl_lock is needed in the query/report event handler logic.
Therefore bottleneck will be disappeared by mc_lock.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When query/report packets are received, mld module processes them.
But they are processed under BH context so it couldn't use sleepable
functions. So, in order to switch context, the two workqueues are
added which processes query and report event.
In the struct inet6_dev, mc_{query | report}_queue are added so it
is per-interface queue.
And mc_{query | report}_work are workqueue structure.
When the query or report event is received, skb is queued to proper
queue and worker function is scheduled immediately.
Workqueues and queues are protected by spinlock, which is
mc_{query | report}_lock, and worker functions are protected by RTNL.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ifmcaddr6 has been protected by inet6_dev->lock(rwlock) so that
the critical section is atomic context. In order to switch this context,
changing locking is needed. The ifmcaddr6 actually already protected by
RTNL So if it's converted to use RCU, its control path context can be
switched to sleepable.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip6_sf_list has been protected by mca_lock(spin_lock) so that the
critical section is atomic context. In order to switch this context,
changing locking is needed. The ip6_sf_list actually already protected
by RTNL So if it's converted to use RCU, its control path context can
be switched to sleepable.
But It doesn't remove mca_lock yet because ifmcaddr6 isn't converted
to RCU yet. So, It's not fully converted to the sleepable context.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sflist has been protected by rwlock so that the critical section
is atomic context.
In order to switch this context, changing locking is needed.
The sflist actually already protected by RTNL So if it's converted
to use RCU, its control path context can be switched to sleepable.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of mc_lock is to protect inet6_dev->mc_tomb.
But mc_tomb is already protected by RTNL and all functions,
which manipulate mc_tomb are called under RTNL.
So, mc_lock is not needed.
Furthermore, it is spinlock so the critical section is atomic.
In order to reduce atomic context, it should be removed.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mcast.c has several timers for delaying works.
Timer's expire handler is working under atomic context so it can't use
sleepable things such as GFP_KERNEL, mutex, etc.
In order to use sleepable APIs, it converts from timers to delayed work.
But there are some critical sections, which is used by both process
and BH context. So that it still uses spin_lock_bh() and rwlock.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the upcoming rev of RFC4941 (IPv6 temporary addresses):
https://tools.ietf.org/html/draft-ietf-6man-rfc4941bis-09
* Reduces the default Valid Lifetime to 2 days
The number of extra addresses employed when Valid Lifetime was
7 days exacerbated the stress caused on network
elements/devices. Additionally, the motivation for temporary
addresses is indeed privacy and reduced exposure. With a
default Valid Lifetime of 7 days, an address that becomes
revealed by active communication is reachable and exposed for
one whole week. The only use case for a Valid Lifetime of 7
days could be some application that is expecting to have long
lived connections. But if you want to have a long lived
connections, you shouldn't be using a temporary address in the
first place. Additionally, in the era of mobile devices, general
applications should nevertheless be prepared and robust to
address changes (e.g. nodes swap wifi <-> 4G, etc.)
* Employs different IIDs for different prefixes
To avoid network activity correlation among addresses configured
for different prefixes
* Uses a simpler algorithm for IID generation
No need to store "history" anywhere
Signed-off-by: Fernando Gont <fgont@si6networks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove two holes on 64bit arches, to bring the size
to one cache line exactly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
icmp6_send() function is expensive on systems with a large number of
interfaces. Every time it’s called, it has to verify that the source
address does not correspond to an existing anycast address by looping
through every device and every anycast address on the device. This can
result in significant delays for a CPU when there are a large number of
neighbors and ND timers are frequently timing out and calling
neigh_invalidate().
Add anycast addresses to a global hashtable to allow quick searching for
matching anycast addresses. This is based on inet6_addr_lst in addrconf.c.
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for IFA_RT_PRIORITY to ipv6 addresses.
If the metric is changed on an existing address then the new route
is inserted before removing the old one. Since the metric is one
of the route keys, the prefix route can not be atomically replaced.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
aca_idev has only 1 user - inet6_fill_ifacaddr - and it only
wants the device index which can be extracted from the fib6_info
nexthop.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all code paths referencing a FIB entry from
rt6_info to fib6_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address generation mode for IPv6 link-local can only be configured
by netlink messages. This patch adds the ability to change the address
generation mode via sysctl.
v1 -> v2
Removed the rtnl lock and switch to use RCU lock to iterate through
the netdev list.
v2 -> v3
Removed the addrgenmode variable from the idev structure and use the
systcl storage for the flag.
Simplifed the logic for sysctl handling by removing the supported
for all operation.
Added support for more types of tunnel interfaces for link-local
address generation.
Based the patches from net-next.
v3 -> v4
Removed unnecessary whitespace changes.
Signed-off-by: Felix Jia <felix.jia@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemented RFC7527 Enhanced DAD.
IPv6 duplicate address detection can fail if there is some temporary
loopback of Ethernet frames. RFC7527 solves this by including a random
nonce in the NS messages used for DAD, and if an NS is received with the
same nonce it is assumed to be a looped back DAD probe and is ignored.
RFC7527 is enabled by default. Can be disabled by setting both of
conf/{all,interface}/enhanced_dad to zero.
Signed-off-by: Erik Nordmark <nordmark@arista.com>
Signed-off-by: Bob Gilligan <gilligan@arista.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv6 temporary address generation uses a variable called DESYNC_FACTOR
to prevent hosts updating the addresses at the same time. Quoting RFC 4941:
... The value DESYNC_FACTOR is a random value (different for each
client) that ensures that clients don't synchronize with each other and
generate new addresses at exactly the same time ...
DESYNC_FACTOR is defined as:
DESYNC_FACTOR -- A random value within the range 0 - MAX_DESYNC_FACTOR.
It is computed once at system start (rather than each time it is used)
and must never be greater than (TEMP_VALID_LIFETIME - REGEN_ADVANCE).
First, I believe the RFC has a typo in it and meant to say: "and must
never be greater than (TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE)"
The reason is that at various places in the RFC, DESYNC_FACTOR is used in
a calculation like (TEMP_PREFERRED_LIFETIME - DESYNC_FACTOR) or
(TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE - DESYNC_FACTOR). It needs to be
smaller than (TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE) for the result of
these calculations to be larger than zero. It's never used in a
calculation together with TEMP_VALID_LIFETIME.
I already submitted an errata to the rfc-editor:
https://www.rfc-editor.org/errata_search.php?rfc=4941
The Linux implementation of DESYNC_FACTOR is very wrong:
max_desync_factor is used in places DESYNC_FACTOR should be used.
max_desync_factor is initialized to the RFC-recommended value for
MAX_DESYNC_FACTOR (600) but the whole point is to get a _random_ value.
And nothing ensures that the value used is not greater than
(TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE), which leads to underflows. The
effect can easily be observed when setting the temp_prefered_lft sysctl
e.g. to 60. The preferred lifetime of the temporary addresses will be
bogus.
TEMP_PREFERRED_LIFETIME and REGEN_ADVANCE are not constants and can be
influenced by these three sysctls: regen_max_retry, dad_transmits and
temp_prefered_lft. Thus, the upper bound for desync_factor needs to be
re-calculated each time a new address is generated and if desync_factor is
larger than the new upper bound, a new random value needs to be
re-generated.
And since we already have max_desync_factor configurable per interface, we
also need to calculate and store desync_factor per interface.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The randomized interface identifier (rndid) was periodically updated from
the regen_timer timer. Simplify the code by updating the rndid only when
needed by ipv6_try_regen_rndid().
This makes the follow-up DESYNC_FACTOR fix much simpler. Also it fixes a
reference counting error in this error path, where an in6_dev_put was
missing:
err = addrconf_sysctl_register(ndev);
if (err) {
ipv6_mc_destroy_dev(ndev);
- del_timer(&ndev->regen_timer);
snmp6_unregister_dev(ndev);
goto err_release;
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements:
https://tools.ietf.org/html/rfc7559
Backoff is performed according to RFC3315 section 14:
https://tools.ietf.org/html/rfc3315#section-14
We allow setting /proc/sys/net/ipv6/conf/*/router_solicitations
to a negative value meaning an unlimited number of retransmits,
and we make this the new default (inline with the RFC).
We also add a new setting:
/proc/sys/net/ipv6/conf/*/router_solicitation_max_interval
defaulting to 1 hour (per RFC recommendation).
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Erik Kline <ek@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a DAD conflict is detected, we want to retry privacy stable address
generation up to idgen_retries (= 3) times with a delay of idgen_delay
(= 1 second). Add the logic to addrconf_dad_failure.
By design, we don't clean up dad failed permanent addresses.
Cc: Erik Kline <ek@google.com>
Cc: Fernando Gont <fgont@si6networks.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: YOSHIFUJI Hideaki/吉藤英明 <hideaki.yoshifuji@miraclelinux.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Erik Kline <ek@google.com>
Cc: Fernando Gont <fgont@si6networks.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: YOSHIFUJI Hideaki/吉藤英明 <hideaki.yoshifuji@miraclelinux.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
the inet6 state INET6_IFADDR_STATE_UP only appeared in its definition.
Cc: Christoph Paasch <christoph.paasch@uclouvain.be>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sébastien Barré <sebastien.barre@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a possibility for userspace to set various (so far
two) modes of generating addresses. This is useful for example for
NetworkManager because it can set the mode to NONE and take care of link
local addresses itself. That allow it to have the interface up,
monitoring carrier but still don't have any addresses on it.
One more use-case by Dan Williams:
<quote>
WWAN devices often have their LL address provided by the firmware of the
device, which sometimes refuses to respond to incorrect LL addresses
when doing DHCPv6 or IPv6 ND. The kernel cannot generate the correct LL
address for two reasons:
1) WWAN pseudo-ethernet interfaces often construct a fake MAC address,
or read a meaningless MAC address from the firmware. Thus the EUI64 and
the IPv6LL address the kernel assigns will be wrong. The real LL
address is often retrieved from the firmware with AT or proprietary
commands.
2) WWAN PPP interfaces receive their LL address from IPV6CP, not from
kernel assignments. Only after IPV6CP has completed do we know the LL
address of the PPP interface and its peer. But the kernel has already
assigned an incorrect LL address to the interface.
So being able to suppress the kernel LL address generation and assign
the one retrieved from the firmware is less complicated and more robust.
</quote>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
addrconf_join_solict and addrconf_join_anycast may cause actions which
need rtnl locked, especially on first address creation.
A new DAD state is introduced which defers processing of the initial
DAD processing into a workqueue.
To get rtnl lock we need to push the code paths which depend on those
calls up to workqueues, specifically addrconf_verify and the DAD
processing.
(v2)
addrconf_dad_failure needs to be queued up to the workqueue, too. This
patch introduces a new DAD state and stop the DAD processing in the
workqueue (this is because of the possible ipv6_del_addr processing
which removes the solicited multicast address from the device).
addrconf_verify_lock is removed, too. After the transition it is not
needed any more.
As we are not processing in bottom half anymore we need to be a bit more
careful about disabling bottom half out when we lock spin_locks which are also
used in bh.
Relevant backtrace:
[ 541.030090] RTNL: assertion failed at net/core/dev.c (4496)
[ 541.031143] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G O 3.10.33-1-amd64-vyatta #1
[ 541.031145] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[ 541.031146] ffffffff8148a9f0 000000000000002f ffffffff813c98c1 ffff88007c4451f8
[ 541.031148] 0000000000000000 0000000000000000 ffffffff813d3540 ffff88007fc03d18
[ 541.031150] 0000880000000006 ffff88007c445000 ffffffffa0194160 0000000000000000
[ 541.031152] Call Trace:
[ 541.031153] <IRQ> [<ffffffff8148a9f0>] ? dump_stack+0xd/0x17
[ 541.031180] [<ffffffff813c98c1>] ? __dev_set_promiscuity+0x101/0x180
[ 541.031183] [<ffffffff813d3540>] ? __hw_addr_create_ex+0x60/0xc0
[ 541.031185] [<ffffffff813cfe1a>] ? __dev_set_rx_mode+0xaa/0xc0
[ 541.031189] [<ffffffff813d3a81>] ? __dev_mc_add+0x61/0x90
[ 541.031198] [<ffffffffa01dcf9c>] ? igmp6_group_added+0xfc/0x1a0 [ipv6]
[ 541.031208] [<ffffffff8111237b>] ? kmem_cache_alloc+0xcb/0xd0
[ 541.031212] [<ffffffffa01ddcd7>] ? ipv6_dev_mc_inc+0x267/0x300 [ipv6]
[ 541.031216] [<ffffffffa01c2fae>] ? addrconf_join_solict+0x2e/0x40 [ipv6]
[ 541.031219] [<ffffffffa01ba2e9>] ? ipv6_dev_ac_inc+0x159/0x1f0 [ipv6]
[ 541.031223] [<ffffffffa01c0772>] ? addrconf_join_anycast+0x92/0xa0 [ipv6]
[ 541.031226] [<ffffffffa01c311e>] ? __ipv6_ifa_notify+0x11e/0x1e0 [ipv6]
[ 541.031229] [<ffffffffa01c3213>] ? ipv6_ifa_notify+0x33/0x50 [ipv6]
[ 541.031233] [<ffffffffa01c36c8>] ? addrconf_dad_completed+0x28/0x100 [ipv6]
[ 541.031241] [<ffffffff81075c1d>] ? task_cputime+0x2d/0x50
[ 541.031244] [<ffffffffa01c38d6>] ? addrconf_dad_timer+0x136/0x150 [ipv6]
[ 541.031247] [<ffffffffa01c37a0>] ? addrconf_dad_completed+0x100/0x100 [ipv6]
[ 541.031255] [<ffffffff8105313a>] ? call_timer_fn.isra.22+0x2a/0x90
[ 541.031258] [<ffffffffa01c37a0>] ? addrconf_dad_completed+0x100/0x100 [ipv6]
Hunks and backtrace stolen from a patch by Stephen Hemminger.
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
net/ipv4/tcp_metrics.c
Overlapping changes between the "don't create two tcp metrics objects
with the same key" race fix in net and the addition of the destination
address in the lookup key in net-next.
Minor overlapping changes in bnx2x driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 1ec047eb47 ("ipv6: introduce per-interface counter for
dad-completed ipv6 addresses") I build the detection of the first
operational link-local address much to complex. Additionally this code
now has a race condition.
Replace it with a much simpler variant, which just scans the address
list when duplicate address detection completes, to check if this is
the first valid link local address and send RS and MLD reports then.
Fixes: 1ec047eb47 ("ipv6: introduce per-interface counter for dad-completed ipv6 addresses")
Reported-by: Jiri Pirko <jiri@resnulli.us>
Cc: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Flavio Leitner <fbl@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no more space in u8 ifa_flags. So do what davem suffested and
add another netlink attr called IFA_FLAGS for carry more flags.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Thomas Haller <thaller@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for privacy extentions is very mature, and making it
configurable only gives marginal memory/code savings in exchange
for obfuscation and hard to read code via CPP ifdef'ery.
Signed-off-by: David S. Miller <davem@davemloft.net>
i) RFC3810, 9.2. Query Interval [QI] says:
The Query Interval variable denotes the interval between General
Queries sent by the Querier. Default value: 125 seconds. [...]
ii) RFC3810, 9.3. Query Response Interval [QRI] says:
The Maximum Response Delay used to calculate the Maximum Response
Code inserted into the periodic General Queries. Default value:
10000 (10 seconds) [...] The number of seconds represented by the
[Query Response Interval] must be less than the [Query Interval].
iii) RFC3810, 9.12. Older Version Querier Present Timeout [OVQPT] says:
The Older Version Querier Present Timeout is the time-out for
transitioning a host back to MLDv2 Host Compatibility Mode. When an
MLDv1 query is received, MLDv2 hosts set their Older Version Querier
Present Timer to [Older Version Querier Present Timeout].
This value MUST be ([Robustness Variable] times (the [Query Interval]
in the last Query received)) plus ([Query Response Interval]).
Hence, on *default* the timeout results in:
[RV] = 2, [QI] = 125sec, [QRI] = 10sec
[OVQPT] = [RV] * [QI] + [QRI] = 260sec
Having that said, we currently calculate [OVQPT] (here given as 'switchback'
variable) as ...
switchback = (idev->mc_qrv + 1) * max_delay
RFC3810, 9.12. says "the [Query Interval] in the last Query received". In
section "9.14. Configuring timers", it is said:
This section is meant to provide advice to network administrators on
how to tune these settings to their network. Ambitious router
implementations might tune these settings dynamically based upon
changing characteristics of the network. [...]
iv) RFC38010, 9.14.2. Query Interval:
The overall level of periodic MLD traffic is inversely proportional
to the Query Interval. A longer Query Interval results in a lower
overall level of MLD traffic. The value of the Query Interval MUST
be equal to or greater than the Maximum Response Delay used to
calculate the Maximum Response Code inserted in General Query
messages.
I assume that was why switchback is calculated as is (3 * max_delay), although
this setting seems to be meant for routers only to configure their [QI]
interval for non-default intervals. So usage here like this is clearly wrong.
Concluding, the current behaviour in IPv6's multicast code is not conform
to the RFC as switch back is calculated wrongly. That is, it has a too small
value, so MLDv2 hosts switch back again to MLDv2 way too early, i.e. ~30secs
instead of ~260secs on default.
Hence, introduce necessary helper functions and fix this up properly as it
should be.
Introduced in 06da92283 ("[IPV6]: Add MLDv2 support."). Credits to Hannes
Frederic Sowa who also had a hand in this as well. Also thanks to Hangbin Liu
who did initial testing.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: David Stevens <dlstevens@us.ibm.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC3590/RFC3810 specifies we should resend MLD reports as soon as a
valid link-local address is available.
We now use the valid_ll_addr_cnt to check if it is necessary to resend
a new report.
Changes since Flavio Leitner's version:
a) adapt for valid_ll_addr_cnt
b) resend first reports directly in the path and just arm the timer for
mc_qrv-1 resends.
Reported-by: Flavio Leitner <fleitner@redhat.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To reduce the number of unnecessary router solicitations, MLDv2 and IGMPv3
messages we need to track the number of valid (as in non-optimistic,
no-dad-failed and non-tentative) link-local addresses. Therefore, this
patch implements a valid_ll_addr_cnt in struct inet6_dev.
We now only emit router solicitations if the first link-local address
finishes duplicate address detection.
The changes for MLDv2 and IGMPv3 are in a follow-up patch.
While there, also simplify one if statement(one minor nit I made in one
of my previous patches):
if (!...)
do();
else
return;
<<into>>
if (...)
return;
do();
Cc: Flavio Leitner <fbl@redhat.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Cc: David Stevens <dlstevens@us.ibm.com>
Suggested-by: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch splits the timers for duplicate address detection and router
solicitations apart. The router solicitations timer goes into inet6_dev
and the dad timer stays in inet6_ifaddr.
The reason behind this patch is to reduce the number of unneeded router
solicitations send out by the host if additional link-local addresses
are created. Currently we send out RS for every link-local address on
an interface.
If the RS timer fires we pick a source address with ipv6_get_lladdr. This
change could hurt people adding additional link-local addresses and
specifying these addresses in the radvd clients section because we
no longer guarantee that we use every ll address as source address in
router solicitations.
Cc: Flavio Leitner <fleitner@redhat.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reviewed-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The next pointer within the inet6_dev structure seems not to be used
anywhere. So just remove it. Tested with allmodconfig on x86_64.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of peer address for IPv6. For example, it is
possible to specify the remote end of a 6inY tunnel.
This was already possible in IPv4:
ip addr add ip1 peer ip2 dev dev1
The peer address is specified with IFA_ADDRESS and the local address with
IFA_LOCAL (like explained in include/uapi/linux/if_addr.h).
Note that the API is not changed, because before this patch, it was not
possible to specify two different addresses in IFA_LOCAL and IFA_REMOTE.
There is a small change for the dump: if the peer is different from ::,
IFA_ADDRESS will contain the peer address instead of the local address.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of invalidating all IPv6 addresses with global scope
when one decides to use IPv6 tokens, we should only invalidate
previous tokens and leave the rest intact until they expire
eventually (or are intact forever). For doing this less greedy
approach, we're adding a bool at the end of inet6_ifaddr structure
instead, for two reasons: i) per-inet6_ifaddr flag space is
already used up, making it wider might not be a good idea,
since ii) also we do not necessarily need to export this
information into user space.
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for IPv6 tokenized IIDs, that allow
for administrators to assign well-known host-part addresses
to nodes whilst still obtaining global network prefix from
Router Advertisements. It is currently in draft status.
The primary target for such support is server platforms
where addresses are usually manually configured, rather
than using DHCPv6 or SLAAC. By using tokenised identifiers,
hosts can still determine their network prefix by use of
SLAAC, but more readily be automatically renumbered should
their network prefix change. [...]
The disadvantage with static addresses is that they are
likely to require manual editing should the network prefix
in use change. If instead there were a method to only
manually configure the static identifier part of the IPv6
address, then the address could be automatically updated
when a new prefix was introduced, as described in [RFC4192]
for example. In such cases a DNS server might be
configured with such a tokenised interface identifier of
::53, and SLAAC would use the token in constructing the
interface address, using the advertised prefix. [...]
http://tools.ietf.org/html/draft-chown-6man-tokenised-ipv6-identifiers-02
The implementation is partially based on top of Mark K.
Thompson's proof of concept. However, it uses the Netlink
interface for configuration resp. data retrival, so that
it can be easily extended in future. Successfully tested
by myself.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to delete the Token ring support. This removes any
special processing in the core networking for token ring, (aside
from net/tr.c itself), leaving the drivers and remaining tokenring
support present but inert.
The mass removal of the drivers and net/tr.c will be in a separate
commit, so that the history of these files that we still care
about won't have the giant deletion tied into their history.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Use of "unsigned int" is preferred to bare "unsigned" in net tree.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the code to handle some of the differences between
RFC 3041 and RFC 4941, which obsoletes it. Also a couple
of janitorial fixes.
- Allow router advertisements to increase the lifetime of
temporary addresses. This was not allowed by RFC 3041,
but is specified by RFC 4941. It is useful when RA
lifetimes are lower than TEMP_{VALID,PREFERRED}_LIFETIME:
in this case, the previous code would delete or deprecate
addresses prematurely.
- Change the default of MAX_RETRY to 3 per RFC 4941.
- Add a comment to clarify that the preferred and valid
lifetimes in inet6_ifaddr are relative to the timestamp.
- Shorten lines to 80 characters in a couple of places.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6 has per device ICMP SNMP counters, taking too much space because
they use percpu storage.
needed size per device is :
(512+4)*sizeof(long)*number_of_possible_cpus*2
On a 32bit kernel, 16 possible cpus, this wastes more than 64kbytes of
memory per ipv6 enabled network device, taken in vmalloc pool.
Since ICMP messages are rare, just use shared counters (atomic_long_t)
Per network space ICMP counters are still using percpu memory, we might
also convert them to shared counters in a future patch.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: David S. Miller <davem@davemloft.net>
These header files are never installed to user consumption, so any
__KERNEL__ cpp checks are superfluous.
Projects should also not copy these files into their userland utility
sources and try to use them there. If they insist on doing so, the
onus is on them to sanitize the headers as needed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add const qualifiers to structs iphdr, ipv6hdr and in6_addr pointers
where possible, to make code intention more obvious.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>