Currently, ethtool does not expose how many lanes are used when the
link is up.
After adding a possibility to advertise or force a specific number of
lanes, the lanes in use value can be either the maximum width of the port
or below.
Extend ethtool to expose the number of lanes currently in use for
drivers that support it.
For example:
$ ethtool -s swp1 speed 100000 lanes 4
$ ethtool -s swp2 speed 100000 lanes 4
$ ip link set swp1 up
$ ip link set swp2 up
$ ethtool swp1
Settings for swp1:
Supported ports: [ FIBRE Backplane ]
Supported link modes: 1000baseT/Full
10000baseT/Full
1000baseKX/Full
10000baseKR/Full
10000baseR_FEC
40000baseKR4/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseKR/Full
25000baseSR/Full
50000baseCR2/Full
50000baseKR2/Full
100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
50000baseSR2/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
10000baseER/Full
50000baseKR/Full
50000baseSR/Full
50000baseCR/Full
50000baseLR_ER_FR/Full
50000baseDR/Full
100000baseKR2/Full
100000baseSR2/Full
100000baseCR2/Full
100000baseLR2_ER2_FR2/Full
100000baseDR2/Full
200000baseKR4/Full
200000baseSR4/Full
200000baseLR4_ER4_FR4/Full
200000baseDR4/Full
200000baseCR4/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 1000baseT/Full
10000baseT/Full
1000baseKX/Full
1000baseKX/Full
10000baseKR/Full
10000baseR_FEC
40000baseKR4/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseKR/Full
25000baseSR/Full
50000baseCR2/Full
50000baseKR2/Full
100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
50000baseSR2/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
10000baseER/Full
200000baseKR4/Full
200000baseSR4/Full
200000baseLR4_ER4_FR4/Full
200000baseDR4/Full
200000baseCR4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Advertised link modes: 100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: 100000Mb/s
Lanes: 4
Duplex: Full
Auto-negotiation: on
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Link detected: yes
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when user space queries the link's parameters, as speed and
duplex, each parameter is passed from the driver to ethtool.
Instead, get the link mode bit in use, and derive each of the parameters
from it in ethtool.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when auto negotiation is on, the user can advertise all the
linkmodes which correspond to a specific speed, but does not have a
similar selector for the number of lanes. This is significant when a
specific speed can be achieved using different number of lanes. For
example, 2x50 or 4x25.
Add 'ETHTOOL_A_LINKMODES_LANES' attribute and expand 'struct
ethtool_link_settings' with lanes field in order to implement a new
lanes-selector that will enable the user to advertise a specific number
of lanes as well.
When auto negotiation is off, lanes parameter can be forced only if the
driver supports it. Add a capability bit in 'struct ethtool_ops' that
allows ethtool know if the driver can handle the lanes parameter when
auto negotiation is off, so if it does not, an error message will be
returned when trying to set lanes.
Example:
$ ethtool -s swp1 lanes 4
$ ethtool swp1
Settings for swp1:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseKX/Full
10000baseKR/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseSR/Full
50000baseCR2/Full
100000baseSR4/Full
100000baseCR4/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
100000baseSR4/Full
100000baseCR4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Unknown! (255)
Auto-negotiation: on
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Link detected: no
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Create a new function for input validations to be called before
rtnl_lock() and move the master slave validation to that function.
This would be a cleanup for next patch that would add another validation
to the new function.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The bridge emits VLAN filtering events and quite a few others via
switchdev with orig_dev = br->dev. After the blamed commit, these events
started getting ignored.
The point of the patch was to not offload switchdev objects for ports
that didn't go through dsa_port_bridge_join, because the configuration
is unsupported:
- ports that offload a bonding/team interface go through
dsa_port_bridge_join when that bonding/team interface is later bridged
with another switch port or LAG
- ports that don't offload LAG don't get notified of the bridge that is
on top of that LAG.
Sadly, a check is missing, which is that the orig_dev is equal to the
bridge device. This check is compatible with the original intention,
because ports that don't offload bridging because they use a software
LAG don't have dp->bridge_dev set.
On a semi-related note, we should not offload switchdev objects or
populate dp->bridge_dev if the driver doesn't implement .port_bridge_join
either. However there is no regression associated with that, so it can
be done separately.
Fixes: 5696c8aedf ("net: dsa: Don't offload port attributes on standalone ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Tobias Waldekranz <tobias@waldekranz.com>
Link: https://lore.kernel.org/r/20210202233109.1591466-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch avoids the indirect call for the common case:
ip6_dst_check and ipv4_dst_check
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch avoids the indirect call for the common case:
ip6_mtu and ipv4_mtu
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch avoids the indirect call for the common case:
ip6_output and ip_output
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch avoids the indirect call for the common case:
ip_local_deliver and ip6_input
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
inet_gro_receive() and inet_gro_complete() are part
of GRO engine which can not be modular.
Similarly, inet_gso_segment() does not need to be exported,
being part of GSO stack.
In other words, net/ipv6/ip6_offload.o is part of vmlinux,
regardless of CONFIG_IPV6.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20210202154145.1568451-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- cfg80211_dev_rename() requires RTNL
- cfg80211_change_iface() and cfg80211_set_encryption()
require wiphy mutex (was missing in wireless extensions)
- cfg80211_destroy_ifaces() requires wiphy mutex
- netdev registration can fail due to notifiers, and then
notifiers are "unrolled", need to handle this properly
-----BEGIN PGP SIGNATURE-----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=bgnR
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-02-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time, only RTNL locking reduction fallout.
- cfg80211_dev_rename() requires RTNL
- cfg80211_change_iface() and cfg80211_set_encryption()
require wiphy mutex (was missing in wireless extensions)
- cfg80211_destroy_ifaces() requires wiphy mutex
- netdev registration can fail due to notifiers, and then
notifiers are "unrolled", need to handle this properly
* tag 'mac80211-next-for-net-next-2021-02-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next:
cfg80211: fix netdev registration deadlock
cfg80211: call cfg80211_destroy_ifaces() with wiphy lock held
wext: call cfg80211_set_encryption() with wiphy lock held
wext: call cfg80211_change_iface() with wiphy lock held
nl80211: call cfg80211_dev_rename() under RTNL
====================
Link: https://lore.kernel.org/r/20210202144106.38207-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds the mibs for ADD_ADDR with port:
MPTCP_MIB_PORTADD for received ADD_ADDR suboption with a port number.
MPTCP_MIB_PORTSYNRX, MPTCP_MIB_PORTSYNACKRX, MPTCP_MIB_PORTACKRX, for
received MP_JOIN's SYN or SYN/ACK or ACK with a port number which is
different from the msk's port number.
MPTCP_MIB_MISMATCHPORTSYNRX and MPTCP_MIB_MISMATCHPORTACKRX, for
received SYN or ACK MP_JOIN with a mismatched port-number.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds MPTCP_PM_ADDR_ATTR_PORT filling and parsing in PM
netlink.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When dealing with the addresses list local_addr_list or anno_list, we
should enable the function addresses_equal's parameter use_port. And
enable it in address_zero too.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds two new helpers, subflow_use_different_sport and
subflow_use_different_dport, to check whether the subflow's source or
destination port number is different from the msk's port number. When
receiving the MP_JOIN's SYN/SYNACK/ACK, we do these port number checks
and print out the different port numbers.
And furthermore, when receiving the MP_JOIN's SYN/ACK, we also use a new
helper mptcp_pm_sport_in_anno_list to check whether this port number is
announced. If it isn't, we need to abort this connection.
This patch also populates the local address's port field in
local_address.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds a new helper named subflow_req_create_thmac, which is
extracted from subflow_token_join_request. It initializes subflow_req's
local_nonce and thmac fields, those are the more expensive to populate.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch drops the unused parameter skb in subflow_token_join_request.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch creates a listening socket when an address with a port-number
is added by PM netlink. Then binds the new port to the socket, and
listens for new connections.
When the address is removed or the addresses are flushed by PM netlink,
release the listening socket.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch changes the sending ACK conditions for the ADD_ADDR, send an
ACK packet for any ADD_ADDR, not just when ipv6 addresses or port
numbers are included.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/139
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when a new MPTCP endpoint is added, the existing MPTCP
sockets are not affected.
This patch implements a new function mptcp_nl_add_subflow_or_signal_addr,
invoked when an address is added from PM netlink. This function traverses
the MPTCP sockets list and invokes mptcp_pm_create_subflow_or_signal_addr
to try to create a subflow or signal an address for the newly added
address, if local constraint allows that.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/19
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch drops the per-msk values add_addr_signal_max,
add_addr_accept_max, local_addr_max and subflows_max fields in struct
mptcp_pm_data, uses the pernet *_max values instead. And adds four new
helpers to get the pernet *_max values separately.
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch uses WRITE_ONCE() for all the pernet add_addr_signal_max,
add_addr_accept_max, local_addr_max and subflows_max fields in struct
pm_nl_pernet to avoid concurrency issues.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After installing a route to the kernel, user space receives an
acknowledgment, which means the route was installed in the kernel,
but not necessarily in hardware.
The asynchronous nature of route installation in hardware can lead
to a routing daemon advertising a route before it was actually installed in
hardware. This can result in packet loss or mis-routed packets until the
route is installed in hardware.
It is also possible for a route already installed in hardware to change
its action and therefore its flags. For example, a host route that is
trapping packets can be "promoted" to perform decapsulation following
the installation of an IPinIP/VXLAN tunnel.
Emit RTM_NEWROUTE notifications whenever RTM_F_OFFLOAD/RTM_F_TRAP flags
are changed. The aim is to provide an indication to user-space
(e.g., routing daemons) about the state of the route in hardware.
Introduce a sysctl that controls this behavior.
Keep the default value at 0 (i.e., do not emit notifications) for several
reasons:
- Multiple RTM_NEWROUTE notification per-route might confuse existing
routing daemons.
- Convergence reasons in routing daemons.
- The extra notifications will negatively impact the insertion rate.
- Not all users are interested in these notifications.
Move fib6_info_hw_flags_set() to C file because it is no longer a short
function.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After installing a route to the kernel, user space receives an
acknowledgment, which means the route was installed in the kernel,
but not necessarily in hardware.
The asynchronous nature of route installation in hardware can lead to a
routing daemon advertising a route before it was actually installed in
hardware. This can result in packet loss or mis-routed packets until the
route is installed in hardware.
It is also possible for a route already installed in hardware to change
its action and therefore its flags. For example, a host route that is
trapping packets can be "promoted" to perform decapsulation following
the installation of an IPinIP/VXLAN tunnel.
Emit RTM_NEWROUTE notifications whenever RTM_F_OFFLOAD/RTM_F_TRAP flags
are changed. The aim is to provide an indication to user-space
(e.g., routing daemons) about the state of the route in hardware.
Introduce a sysctl that controls this behavior.
Keep the default value at 0 (i.e., do not emit notifications) for several
reasons:
- Multiple RTM_NEWROUTE notification per-route might confuse existing
routing daemons.
- Convergence reasons in routing daemons.
- The extra notifications will negatively impact the insertion rate.
- Not all users are interested in these notifications.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Acked-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Publish fib_nlmsg_size() to allow it to be used later on from
fib_alias_hw_flags_set().
Remove the inline keyword since it shouldn't be used inside C files.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
fib_dump_info() does not change 'fri', so pass it as 'const'.
It will later allow us to invoke fib_dump_info() from
fib_alias_hw_flags_set().
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Avoid the assumption that ksize(kmalloc(S)) == ksize(kmalloc(S)): when
cloning an skb, save and restore truesize after pskb_expand_head(). This
can occur if the allocator decides to service an allocation of the same
size differently (e.g. use a different size class, or pass the
allocation on to KFENCE).
Because truesize is used for bookkeeping (such as sk_wmem_queued), a
modified truesize of a cloned skb may result in corrupt bookkeeping and
relevant warnings (such as in sk_stream_kill_queues()).
Link: https://lkml.kernel.org/r/X9JR/J6dMMOy1obu@elver.google.com
Reported-by: syzbot+7b99aafdcc2eedea6178@syzkaller.appspotmail.com
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Marco Elver <elver@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210201160420.2826895-1-elver@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With version 0 of the protocol it was legal to encode the 'Subflow Id' in
the MP_PRIO suboption, to specify which subflow would change its 'Backup'
flag. This has been removed from v1 specification: thus, according to RFC
8684 §3.3.8, the resulting 'Length' for MP_PRIO changed from 4 to 3 byte.
Current Linux generates / parses MP_PRIO according to the old spec, using
'Length' equal to 4, and hardcoding 1 as 'Subflow Id'; RFC compliance can
improve if we change 'Length' in other to become 3, leaving a 'Nop' after
the MP_PRIO suboption. In this way the kernel will emit and accept *only*
MP_PRIO suboptions that are compliant to version 1 of the MPTCP protocol.
unpatched 5.11-rc kernel:
[root@bottarga ~]# tcpdump -tnnr unpatched.pcap | grep prio
reading from file unpatched.pcap, link-type LINUX_SLL (Linux cooked v1)
dropped privs to tcpdump
IP 10.0.3.2.48433 > 10.0.1.1.10006: Flags [.], ack 1, win 502, options [nop,nop,TS val 4032325513 ecr 1876514270,mptcp prio non-backup id 1,mptcp dss ack 14084896651682217737], length 0
patched 5.11-rc kernel:
[root@bottarga ~]# tcpdump -tnnr patched.pcap | grep prio
reading from file patched.pcap, link-type LINUX_SLL (Linux cooked v1)
dropped privs to tcpdump
IP 10.0.3.2.49735 > 10.0.1.1.10006: Flags [.], ack 1, win 502, options [nop,nop,TS val 1276737699 ecr 2686399734,mptcp prio non-backup,nop,mptcp dss ack 18433038869082491686], length 0
Changes since v2:
- when accounting for option space, don't increment 'TCPOLEN_MPTCP_PRIO'
and use 'TCPOLEN_MPTCP_PRIO_ALIGN' instead, thanks to Matthieu Baerts.
Changes since v1:
- refactor patch to avoid using 'TCPOLEN_MPTCP_PRIO' with its old value,
thanks to Geliang Tang.
Fixes: 067065422f ("mptcp: add the outgoing MP_PRIO support")
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Matteo Croce <mcroce@linux.microsoft.com>
Link: https://lore.kernel.org/r/846cdd41e6ad6ec88ef23fee1552ab39c2f5a3d1.1612184361.git.dcaratti@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
trees.
Current release - regressions:
- ip_tunnel: fix mtu calculation
- mlx5: fix function calculation for page trees
Previous releases - regressions:
- vsock: fix the race conditions in multi-transport support
- neighbour: prevent a dead entry from updating gc_list
- dsa: mv88e6xxx: override existent unicast portvec in port_fdb_add
Previous releases - always broken:
- bpf, cgroup: two copy_{from,to}_user() warn_on_once splats for BPF
cgroup getsockopt infra when user space is trying
to race against optlen, from Loris Reiff.
- bpf: add missing fput() in BPF inode storage map update helper
- udp: ipv4: manipulate network header of NATed UDP GRO fraglist
- mac80211: fix station rate table updates on assoc
- r8169: work around RTL8125 UDP HW bug
- igc: report speed and duplex as unknown when device is runtime
suspended
- rxrpc: fix deadlock around release of dst cached on udp tunnel
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAmAZjwQACgkQMUZtbf5S
IruLbQ//Yg9+xEnqhDuOJZtYHB0rsJjLlKmtvgOsBr8BaTcUEPoPoqUPm+EMvCHb
o1fFa1qIrbS5luVEofu9hNX7DGXwvgawaMW2TympJhqLZQqjazCMB/st99LphhJw
RvaZI8aDOikosT4c+I0vm83jDQETonrjziIcPfHHPjn/Q+amGRRRXiTSQnRF/MlU
oARCG+U3kHsHBDUPNSCtSjKXshoZPjFb/pD7fQAlzzm7CssvbPhNWbducueyP2Fb
XW4RwJu9QBBH2JS6uZJ1Y6LVoRzusmE9dUam3KhkiL/CHs72lWPsc+Rn5gbBPvc5
Y4T4h61Xti1O4ULKdqhGceror6XY+4Qb1VlHWWztOhIo00wIAv3IHbTup/4o0HBr
j84MtcyOl/qxSFXjunPJkbWJngXikrkIMS0Bl6ZcPAejYM9wN6vCgbvFCHbEg1Rx
cWFnYyS9FCLduaxHSizv050tWhknOdX+zHK3fOtlW0yWnreJAB8Hoc21Zm7YKvg0
GxxcGK6AhqJ6s2ixVDv7MyJrltJ/hOJQb+T3HgHFuY2BYUs8F2r/HoHU/u4uCl76
RdBzbC/sLnBpMHf6r1rHTnGPsapoJOOYWnej71l425vX1qr5xnmxVNNB6HReObNv
+/jPoRYa5BVsVt2LmDcuH1O32pXJPWKVBR7Yfa6Bn2yzhcbECTc=
=ZByM
-----END PGP SIGNATURE-----
Merge tag 'net-5.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.11-rc7, including fixes from bpf and mac80211
trees.
Current release - regressions:
- ip_tunnel: fix mtu calculation
- mlx5: fix function calculation for page trees
Previous releases - regressions:
- vsock: fix the race conditions in multi-transport support
- neighbour: prevent a dead entry from updating gc_list
- dsa: mv88e6xxx: override existent unicast portvec in port_fdb_add
Previous releases - always broken:
- bpf, cgroup: two copy_{from,to}_user() warn_on_once splats for BPF
cgroup getsockopt infra when user space is trying to race against
optlen, from Loris Reiff.
- bpf: add missing fput() in BPF inode storage map update helper
- udp: ipv4: manipulate network header of NATed UDP GRO fraglist
- mac80211: fix station rate table updates on assoc
- r8169: work around RTL8125 UDP HW bug
- igc: report speed and duplex as unknown when device is runtime
suspended
- rxrpc: fix deadlock around release of dst cached on udp tunnel"
* tag 'net-5.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (36 commits)
net: hsr: align sup_multicast_addr in struct hsr_priv to u16 boundary
net: ipa: fix two format specifier errors
net: ipa: use the right accessor in ipa_endpoint_status_skip()
net: ipa: be explicit about endianness
net: ipa: add a missing __iomem attribute
net: ipa: pass correct dma_handle to dma_free_coherent()
r8169: fix WoL on shutdown if CONFIG_DEBUG_SHIRQ is set
net/rds: restrict iovecs length for RDS_CMSG_RDMA_ARGS
net: mvpp2: TCAM entry enable should be written after SRAM data
net: lapb: Copy the skb before sending a packet
net/mlx5e: Release skb in case of failure in tc update skb
net/mlx5e: Update max_opened_tc also when channels are closed
net/mlx5: Fix leak upon failure of rule creation
net/mlx5: Fix function calculation for page trees
docs: networking: swap words in icmp_errors_use_inbound_ifaddr doc
udp: ipv4: manipulate network header of NATed UDP GRO fraglist
net: ip_tunnel: fix mtu calculation
vsock: fix the race conditions in multi-transport support
net: sched: replaced invalid qdisc tree flush helper in qdisc_replace
ibmvnic: device remove has higher precedence over reset
...
sup_multicast_addr is passed to ether_addr_equal for address comparison
which casts the address inputs to u16 leading to an unaligned access.
Aligning the sup_multicast_addr to u16 boundary fixes the issue.
Signed-off-by: Andreas Oetken <andreas.oetken@siemens.com>
Link: https://lore.kernel.org/r/20210202090304.2740471-1-ennoerlangen@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
syzbot found WARNING in rds_rdma_extra_size [1] when RDS_CMSG_RDMA_ARGS
control message is passed with user-controlled
0x40001 bytes of args->nr_local, causing order >= MAX_ORDER condition.
The exact value 0x40001 can be checked with UIO_MAXIOV which is 0x400.
So for kcalloc() 0x400 iovecs with sizeof(struct rds_iovec) = 0x10
is the closest limit, with 0x10 leftover.
Same condition is currently done in rds_cmsg_rdma_args().
[1] WARNING: mm/page_alloc.c:5011
[..]
Call Trace:
alloc_pages_current+0x18c/0x2a0 mm/mempolicy.c:2267
alloc_pages include/linux/gfp.h:547 [inline]
kmalloc_order+0x2e/0xb0 mm/slab_common.c:837
kmalloc_order_trace+0x14/0x120 mm/slab_common.c:853
kmalloc_array include/linux/slab.h:592 [inline]
kcalloc include/linux/slab.h:621 [inline]
rds_rdma_extra_size+0xb2/0x3b0 net/rds/rdma.c:568
rds_rm_size net/rds/send.c:928 [inline]
Reported-by: syzbot+1bd2b07f93745fa38425@syzkaller.appspotmail.com
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Link: https://lore.kernel.org/r/20210201203233.1324704-1-snovitoll@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When sending a packet, we will prepend it with an LAPB header.
This modifies the shared parts of a cloned skb, so we should copy the
skb rather than just clone it, before we prepend the header.
In "Documentation/networking/driver.rst" (the 2nd point), it states
that drivers shouldn't modify the shared parts of a cloned skb when
transmitting.
The "dev_queue_xmit_nit" function in "net/core/dev.c", which is called
when an skb is being sent, clones the skb and sents the clone to
AF_PACKET sockets. Because the LAPB drivers first remove a 1-byte
pseudo-header before handing over the skb to us, if we don't copy the
skb before prepending the LAPB header, the first byte of the packets
received on AF_PACKET sockets can be corrupted.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20210201055706.415842-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- station rate tables were not updated correctly
after association, leading to bad configuration
- rtl8723bs (staging) was initializing data incorrectly
after the previous fix and needed to move the init
later
-----BEGIN PGP SIGNATURE-----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=mEgj
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-net-2021-02-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Two fixes:
- station rate tables were not updated correctly
after association, leading to bad configuration
- rtl8723bs (staging) was initializing data incorrectly
after the previous fix and needed to move the init
later
* tag 'mac80211-for-net-2021-02-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211:
staging: rtl8723bs: Move wiphy setup to after reading the regulatory settings from the chip
mac80211: fix station rate table updates on assoc
====================
Link: https://lore.kernel.org/r/20210202143505.37610-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
UDP/IP header of UDP GROed frag_skbs are not updated even after NAT
forwarding. Only the header of head_skb from ip_finish_output_gso ->
skb_gso_segment is updated but following frag_skbs are not updated.
A call path skb_mac_gso_segment -> inet_gso_segment ->
udp4_ufo_fragment -> __udp_gso_segment -> __udp_gso_segment_list
does not try to update UDP/IP header of the segment list but copy
only the MAC header.
Update port, addr and check of each skb of the segment list in
__udp_gso_segment_list. It covers both SNAT and DNAT.
Fixes: 9fd1ff5d2a (udp: Support UDP fraglist GRO/GSO.)
Signed-off-by: Dongseok Yi <dseok.yi@samsung.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Link: https://lore.kernel.org/r/1611962007-80092-1-git-send-email-dseok.yi@samsung.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dev->hard_header_len for tunnel interface is set only when header_ops
are set too and already contains full overhead of any tunnel encapsulation.
That's why there is not need to use this overhead twice in mtu calc.
Fixes: fdafed4599 ("ip_gre: set dev->hard_header_len and dev->needed_headroom properly")
Reported-by: Slava Bacherikov <mail@slava.cc>
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Link: https://lore.kernel.org/r/1611959267-20536-1-git-send-email-vfedorenko@novek.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are multiple similar bugs implicitly introduced by the
commit c0cfa2d8a7 ("vsock: add multi-transports support") and
commit 6a2c096210 ("vsock: prevent transport modules unloading").
The bug pattern:
[1] vsock_sock.transport pointer is copied to a local variable,
[2] lock_sock() is called,
[3] the local variable is used.
VSOCK multi-transport support introduced the race condition:
vsock_sock.transport value may change between [1] and [2].
Let's copy vsock_sock.transport pointer to local variables after
the lock_sock() call.
Fixes: c0cfa2d8a7 ("vsock: add multi-transports support")
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Link: https://lore.kernel.org/r/20210201084719.2257066-1-alex.popov@linux.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If register_netdevice() fails after having called cfg80211's
netdev notifier (cfg80211_netdev_notifier_call) it will call
the notifier again with UNREGISTER. This would then lock the
wiphy mutex because we're marked as registered, which causes
a deadlock.
Fix this by separately keeping track of whether or not we're
in the middle of registering to also skip the notifier call
on this unregister.
Reported-by: syzbot+2ae0ca9d7737ad1a62b7@syzkaller.appspotmail.com
Fixes: a05829a722 ("cfg80211: avoid holding the RTNL when calling the driver")
Link: https://lore.kernel.org/r/20210201192048.ed8bad436737.I7cae042c44b15f80919a285799a15df467e9d42d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver uses .sta_add, station entries are only uploaded after the sta
is in assoc state. Fix early station rate table updates by deferring them
until the sta has been uploaded.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210201083324.3134-1-nbd@nbd.name
[use rcu_access_pointer() instead since we won't dereference here]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Highlights include:
Bugfixes:
- SUNRPC: Handle 0 length opaque XDR object data properly
- Fix a layout segment leak in pnfs_layout_process()
- pNFS/NFSv4: Update the layout barrier when we schedule a layoutreturn
- pNFS/NFSv4: Improve rejection of out-of-order layouts
- pNFS/NFSv4: Try to return invalid layout in pnfs_layout_process()
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEESQctxSBg8JpV8KqEZwvnipYKAPIFAmAW4QgACgkQZwvnipYK
APJNZw/6AnLawj0kjn7z0Wc2LA0QWxbAVGYGe28gQdy6qiBbuOiFDeH8itKk6m1c
R6ZPpFHFKYk6+CsNcNws2sz9gBQj7wzDIy3sHenIaiNgY/fWNKDC8woKkJFSUSMl
GSQ9rkCYwRJu1JxP7r/9gnw/86oUTy/PgMaGdz6CMZJlq9iNa8t2UqMOfmcN8EZ3
AIewe4fSV5ebfycVz6btdJy8OCwyUfQ1OMilfh+0+5HYlk/xUxr57+AHi9r8w6bq
3tzIq3imQRgZsPPo/DJo/D4hfeFYX849/Tp+I5ydREWIwREBz2PO8bHNFnDoeoLo
AJ8mkawvpx+jsHFaAHql6STvY7uTY7qqBqsX2qSCqd6n2VEU0+cnDCY1IcgjcfBR
ozaYHJQm9ZhHzska3r/aKBQmkth9LIPU6aIMcYtjzC3ywua2vfCBSPRYKES80kIV
Pzgf5yRZFTEp7jGV9Uhf3Hucm3oIF9WVonDpSPbThdHUUXAYAVK1HZwgWx72HskL
BEhdaD+zsacv58C1+BE3vlh6A/j/cZAQifTfflgkLE3JE1IiKJwFjH4q6jgLwccx
kWLopK9Ds+ta+kLtlCuNTsPt7aGUoZZleH1Ghzdkw5Dfv2eEnR3YM6raa294avw4
DzKE/Rzgv5JuoSJhkWW/PiBZHcxMsv3SK7LTjO2oteFz88olsgo=
=gLzv
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-5.11-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client fixes from Trond Myklebust:
- SUNRPC: Handle 0 length opaque XDR object data properly
- Fix a layout segment leak in pnfs_layout_process()
- pNFS/NFSv4: Update the layout barrier when we schedule a layoutreturn
- pNFS/NFSv4: Improve rejection of out-of-order layouts
- pNFS/NFSv4: Try to return invalid layout in pnfs_layout_process()
* tag 'nfs-for-5.11-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: Handle 0 length opaque XDR object data properly
SUNRPC: Move simple_get_bytes and simple_get_netobj into private header
pNFS/NFSv4: Improve rejection of out-of-order layouts
pNFS/NFSv4: Update the layout barrier when we schedule a layoutreturn
pNFS/NFSv4: Try to return invalid layout in pnfs_layout_process()
pNFS/NFSv4: Fix a layout segment leak in pnfs_layout_process()
Following race condition was detected:
<CPU A, t0> - neigh_flush_dev() is under execution and calls
neigh_mark_dead(n) marking the neighbour entry 'n' as dead.
<CPU B, t1> - Executing: __netif_receive_skb() ->
__netif_receive_skb_core() -> arp_rcv() -> arp_process().arp_process()
calls __neigh_lookup() which takes a reference on neighbour entry 'n'.
<CPU A, t2> - Moves further along neigh_flush_dev() and calls
neigh_cleanup_and_release(n), but since reference count increased in t2,
'n' couldn't be destroyed.
<CPU B, t3> - Moves further along, arp_process() and calls
neigh_update()-> __neigh_update() -> neigh_update_gc_list(), which adds
the neighbour entry back in gc_list(neigh_mark_dead(), removed it
earlier in t0 from gc_list)
<CPU B, t4> - arp_process() finally calls neigh_release(n), destroying
the neighbour entry.
This leads to 'n' still being part of gc_list, but the actual
neighbour structure has been freed.
The situation can be prevented from happening if we disallow a dead
entry to have any possibility of updating gc_list. This is what the
patch intends to achieve.
Fixes: 9c29a2f55e ("neighbor: Fix locking order for gc_list changes")
Signed-off-by: Chinmay Agarwal <chinagar@codeaurora.org>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20210127165453.GA20514@chinagar-linux.qualcomm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
AF_RXRPC sockets use UDP ports in encap mode. This causes socket and dst
from an incoming packet to get stolen and attached to the UDP socket from
whence it is leaked when that socket is closed.
When a network namespace is removed, the wait for dst records to be cleaned
up happens before the cleanup of the rxrpc and UDP socket, meaning that the
wait never finishes.
Fix this by moving the rxrpc (and, by dependence, the afs) private
per-network namespace registrations to the device group rather than subsys
group. This allows cached rxrpc local endpoints to be cleared and their
UDP sockets closed before we try waiting for the dst records.
The symptom is that lines looking like the following:
unregister_netdevice: waiting for lo to become free
get emitted at regular intervals after running something like the
referenced syzbot test.
Thanks to Vadim for tracking this down and work out the fix.
Reported-by: syzbot+df400f2f24a1677cd7e0@syzkaller.appspotmail.com
Reported-by: Vadim Fedorenko <vfedorenko@novek.ru>
Fixes: 5271953cad ("rxrpc: Use the UDP encap_rcv hook")
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Vadim Fedorenko <vfedorenko@novek.ru>
Link: https://lore.kernel.org/r/161196443016.3868642.5577440140646403533.stgit@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We're moving to netlink-only options, so add comments in the bridge's
sysfs files to warn against adding any new sysfs entries.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We decided to stop adding new sysfs bridge options and continue with
netlink only, so remove hosts limit sysfs support.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are use cases for which the existing tagger, based on the NPI
(Node Processor Interface) functionality, is insufficient.
Namely:
- Frames injected through the NPI port bypass the frame analyzer, so no
source address learning is performed, no TSN stream classification,
etc.
- Flow control is not functional over an NPI port (PAUSE frames are
encapsulated in the same Extraction Frame Header as all other frames)
- There can be at most one NPI port configured for an Ocelot switch. But
in NXP LS1028A and T1040 there are two Ethernet CPU ports. The non-NPI
port is currently either disabled, or operated as a plain user port
(albeit an internally-facing one). Having the ability to configure the
two CPU ports symmetrically could pave the way for e.g. creating a LAG
between them, to increase bandwidth seamlessly for the system.
So there is a desire to have an alternative to the NPI mode. This change
keeps the default tagger for the Seville and Felix switches as "ocelot",
but it can be changed via the following device attribute:
echo ocelot-8021q > /sys/class/<dsa-master>/dsa/tagging
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently DSA exposes the following sysfs:
$ cat /sys/class/net/eno2/dsa/tagging
ocelot
which is a read-only device attribute, introduced in the kernel as
commit 98cdb48071 ("net: dsa: Expose tagging protocol to user-space"),
and used by libpcap since its commit 993db3800d7d ("Add support for DSA
link-layer types").
It would be nice if we could extend this device attribute by making it
writable:
$ echo ocelot-8021q > /sys/class/net/eno2/dsa/tagging
This is useful with DSA switches that can make use of more than one
tagging protocol. It may be useful in dsa_loop in the future too, to
perform offline testing of various taggers, or for changing between dsa
and edsa on Marvell switches, if that is desirable.
In terms of implementation, drivers can support this feature by
implementing .change_tag_protocol, which should always leave the switch
in a consistent state: either with the new protocol if things went well,
or with the old one if something failed. Teardown of the old protocol,
if necessary, must be handled by the driver.
Some things remain as before:
- The .get_tag_protocol is currently only called at probe time, to load
the initial tagging protocol driver. Nonetheless, new drivers should
report the tagging protocol in current use now.
- The driver should manage by itself the initial setup of tagging
protocol, no later than the .setup() method, as well as destroying
resources used by the last tagger in use, no earlier than the
.teardown() method.
For multi-switch DSA trees, error handling is a bit more complicated,
since e.g. the 5th out of 7 switches may fail to change the tag
protocol. When that happens, a revert to the original tag protocol is
attempted, but that may fail too, leaving the tree in an inconsistent
state despite each individual switch implementing .change_tag_protocol
transactionally. Since the intersection between drivers that implement
.change_tag_protocol and drivers that support D in DSA is currently the
empty set, the possibility for this error to happen is ignored for now.
Testing:
$ insmod mscc_felix.ko
[ 79.549784] mscc_felix 0000:00:00.5: Adding to iommu group 14
[ 79.565712] mscc_felix 0000:00:00.5: Failed to register DSA switch: -517
$ insmod tag_ocelot.ko
$ rmmod mscc_felix.ko
$ insmod mscc_felix.ko
[ 97.261724] libphy: VSC9959 internal MDIO bus: probed
[ 97.267363] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 0
[ 97.274998] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 1
[ 97.282561] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 2
[ 97.289700] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 3
[ 97.599163] mscc_felix 0000:00:00.5 swp0 (uninitialized): PHY [0000:00:00.3:10] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[ 97.862034] mscc_felix 0000:00:00.5 swp1 (uninitialized): PHY [0000:00:00.3:11] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[ 97.950731] mscc_felix 0000:00:00.5 swp0: configuring for inband/qsgmii link mode
[ 97.964278] 8021q: adding VLAN 0 to HW filter on device swp0
[ 98.146161] mscc_felix 0000:00:00.5 swp2 (uninitialized): PHY [0000:00:00.3:12] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[ 98.238649] mscc_felix 0000:00:00.5 swp1: configuring for inband/qsgmii link mode
[ 98.251845] 8021q: adding VLAN 0 to HW filter on device swp1
[ 98.433916] mscc_felix 0000:00:00.5 swp3 (uninitialized): PHY [0000:00:00.3:13] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[ 98.485542] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode
[ 98.503584] mscc_felix 0000:00:00.5: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 98.527948] device eno2 entered promiscuous mode
[ 98.544755] DSA: tree 0 setup
$ ping 10.0.0.1
PING 10.0.0.1 (10.0.0.1): 56 data bytes
64 bytes from 10.0.0.1: seq=0 ttl=64 time=2.337 ms
64 bytes from 10.0.0.1: seq=1 ttl=64 time=0.754 ms
^C
- 10.0.0.1 ping statistics -
2 packets transmitted, 2 packets received, 0% packet loss
round-trip min/avg/max = 0.754/1.545/2.337 ms
$ cat /sys/class/net/eno2/dsa/tagging
ocelot
$ cat ./test_ocelot_8021q.sh
#!/bin/bash
ip link set swp0 down
ip link set swp1 down
ip link set swp2 down
ip link set swp3 down
ip link set swp5 down
ip link set eno2 down
echo ocelot-8021q > /sys/class/net/eno2/dsa/tagging
ip link set eno2 up
ip link set swp0 up
ip link set swp1 up
ip link set swp2 up
ip link set swp3 up
ip link set swp5 up
$ ./test_ocelot_8021q.sh
./test_ocelot_8021q.sh: line 9: echo: write error: Protocol not available
$ rmmod tag_ocelot.ko
rmmod: can't unload module 'tag_ocelot': Resource temporarily unavailable
$ insmod tag_ocelot_8021q.ko
$ ./test_ocelot_8021q.sh
$ cat /sys/class/net/eno2/dsa/tagging
ocelot-8021q
$ rmmod tag_ocelot.ko
$ rmmod tag_ocelot_8021q.ko
rmmod: can't unload module 'tag_ocelot_8021q': Resource temporarily unavailable
$ ping 10.0.0.1
PING 10.0.0.1 (10.0.0.1): 56 data bytes
64 bytes from 10.0.0.1: seq=0 ttl=64 time=0.953 ms
64 bytes from 10.0.0.1: seq=1 ttl=64 time=0.787 ms
64 bytes from 10.0.0.1: seq=2 ttl=64 time=0.771 ms
$ rmmod mscc_felix.ko
[ 645.544426] mscc_felix 0000:00:00.5: Link is Down
[ 645.838608] DSA: tree 0 torn down
$ rmmod tag_ocelot_8021q.ko
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cascading DSA switches can be done multiple ways. There is the brute
force approach / tag stacking, where one upstream switch, located
between leaf switches and the host Ethernet controller, will just
happily transport the DSA header of those leaf switches as payload.
For this kind of setups, DSA works without any special kind of treatment
compared to a single switch - they just aren't aware of each other.
Then there's the approach where the upstream switch understands the tags
it transports from its leaves below, as it doesn't push a tag of its own,
but it routes based on the source port & switch id information present
in that tag (as opposed to DMAC & VID) and it strips the tag when
egressing a front-facing port. Currently only Marvell implements the
latter, and Marvell DSA trees contain only Marvell switches.
So it is safe to say that DSA trees already have a single tag protocol
shared by all switches, and in fact this is what makes the switches able
to understand each other. This fact is also implied by the fact that
currently, the tagging protocol is reported as part of a sysfs installed
on the DSA master and not per port, so it must be the same for all the
ports connected to that DSA master regardless of the switch that they
belong to.
It's time to make this official and enforce it (yes, this also means we
won't have any "switch understands tag to some extent but is not able to
speak it" hardware oddities that we'll support in the future).
This is needed due to the imminent introduction of the dsa_switch_ops::
change_tag_protocol driver API. When that is introduced, we'll have
to notify switches of the tagging protocol that they're configured to
use. Currently the tag_ops structure pointer is held only for CPU ports.
But there are switches which don't have CPU ports and nonetheless still
need to be configured. These would be Marvell leaf switches whose
upstream port is just a DSA link. How do we inform these of their
tagging protocol setup/deletion?
One answer to the above would be: iterate through the DSA switch tree's
ports once, list the CPU ports, get their tag_ops, then iterate again
now that we have it, and notify everybody of that tag_ops. But what to
do if conflicts appear between one cpu_dp->tag_ops and another? There's
no escaping the fact that conflict resolution needs to be done, so we
can be upfront about it.
Ease our work and just keep the master copy of the tag_ops inside the
struct dsa_switch_tree. Reference counting is now moved to be per-tree
too, instead of per-CPU port.
There are many places in the data path that access master->dsa_ptr->tag_ops
and we would introduce unnecessary performance penalty going through yet
another indirection, so keep those right where they are.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The existence of dsa_broadcast has generated some confusion in the past:
https://www.mail-archive.com/netdev@vger.kernel.org/msg365042.html
So let's document the existing dsa_port_notify and dsa_broadcast
functions and explain when each of them should be used.
Also, in fact, the in-between function has always been there but was
lacking a name, and is the main reason for this patch: dsa_tree_notify.
Refactor dsa_broadcast to use it.
This patch also moves dsa_broadcast (a top-level function) to dsa2.c,
where it really belonged in the first place, but had no companion so it
stood with dsa_port_notify.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sja1105 implementation can be blind about this, but the felix driver
doesn't do exactly what it's being told, so it needs to know whether it
is a TX or an RX VLAN, so it can install the appropriate type of TCAM
rule.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use cache friendly helpers to better use cpu caches
while reading /proc/net/netstat
Tested on a platform with 256 threads (AMD Rome)
Before: 305 usec spent in netstat_seq_show()
After: 130 usec spent in netstat_seq_show()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210128162145.1703601-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
