This field is never used, so remove it. Last use was probably in
23ea8e5a07 ("Btrfs: load checksum data once when submitting a direct
read io").
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Make use of the new iomap_iter->private field to avoid a memory
allocation per iomap range.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Allow the file system to keep state for all iterations. For now only
wire it up for direct I/O as there is an immediate need for it there.
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Add a wrapper around iomap_dio_rw that keeps the direct I/O internals
isolated in inode.c.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
While the active zones within an active block group are reset, and their
active resource is released, the block group itself is kept in the active
block group list and marked as active. As a result, the list will contain
more than max_active_zones block groups. That itself is not fatal for the
device as the zones are properly reset.
However, that inflated list is, of course, strange. Also, a to-appear
patch series, which deactivates an active block group on demand, gets
confused with the wrong list.
So, fix the issue by finishing the unused block group once it gets
read-only, so that we can release the active resource in an early stage.
Fixes: be1a1d7a5d ("btrfs: zoned: finish fully written block group")
CC: stable@vger.kernel.org # 5.16+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Commit be1a1d7a5d ("btrfs: zoned: finish fully written block group")
introduced zone finishing code both for data and metadata end_io path.
However, the metadata side is not working as it should. First, it
compares logical address (eb->start + eb->len) with offset within a
block group (cache->zone_capacity) in submit_eb_page(). That essentially
disabled zone finishing on metadata end_io path.
Furthermore, fixing the issue above revealed we cannot call
btrfs_zone_finish_endio() in end_extent_buffer_writeback(). We cannot
call btrfs_lookup_block_group() which require spin lock inside end_io
context.
Introduce btrfs_schedule_zone_finish_bg() to wait for the extent buffer
writeback and do the zone finish IO in a workqueue.
Also, drop EXTENT_BUFFER_ZONE_FINISH as it is no longer used.
Fixes: be1a1d7a5d ("btrfs: zoned: finish fully written block group")
CC: stable@vger.kernel.org # 5.16+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Currently, btrfs_zone_finish_endio() finishes a block group only when the
written region reaches the end of the block group. We can also finish the
block group when no more allocation is possible.
Fixes: be1a1d7a5d ("btrfs: zoned: finish fully written block group")
CC: stable@vger.kernel.org # 5.16+
Reviewed-by: Pankaj Raghav <p.raghav@samsung.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_zone_finish() and btrfs_zone_finish_endio() have similar code.
Introduce do_zone_finish() to factor out the common code.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Introduce a wrapper to check if all the space in a block group is
allocated or not.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When iterating the backrefs in an extent item if the ptr to the
'current' backref record goes beyond the extent item a warning is
generated and -ENOENT is returned. However what's more appropriate to
debug such cases would be to return EUCLEAN and also print identifying
information about the performed search as well as the current content of
the leaf containing the possibly corrupted extent item.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The bio_ctrl is the last use of bio_flags that has been converted to
compress type everywhere else.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Several functions take parameter bio_flags that was simplified to just
compress type, unify it and change the type accordingly.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The bio_flags is now used to store unchanged compress type, so unify
that.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The helpers extent_set_compress_type and extent_compress_type have
become trivial after previous cleanups and can be removed.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The bio_flags are used only to encode the compression and there are no
other EXTENT_BIO_* flags, so the compress type can be stored directly.
The struct member name is left unchanged and will be cleaned in later
patches.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The helper used to do more with the wbc state but now it's just one
subtraction, no need to have a special helper.
It became trivial in a91326679f ("Btrfs: make mapping->writeback_index
point to the last written page").
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The value of btrfs_delayed_extent_op::is_data is always false, we can
cascade the change and simplify code that depends on it, removing the
structure member eventually.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The parameter has been added in 2009 in the infamous monster commit
5d4f98a28c ("Btrfs: Mixed back reference (FORWARD ROLLING FORMAT
CHANGE)") but not used ever since. We can sink it and allow further
simplifications.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When reserving data space for a direct IO write we can end up deadlocking
if we have multiple tasks attempting a write to the same file range, there
are multiple extents covered by that file range, we are low on available
space for data and the writes don't expand the inode's i_size.
The deadlock can happen like this:
1) We have a file with an i_size of 1M, at offset 0 it has an extent with
a size of 128K and at offset 128K it has another extent also with a
size of 128K;
2) Task A does a direct IO write against file range [0, 256K), and because
the write is within the i_size boundary, it takes the inode's lock (VFS
level) in shared mode;
3) Task A locks the file range [0, 256K) at btrfs_dio_iomap_begin(), and
then gets the extent map for the extent covering the range [0, 128K).
At btrfs_get_blocks_direct_write(), it creates an ordered extent for
that file range ([0, 128K));
4) Before returning from btrfs_dio_iomap_begin(), it unlocks the file
range [0, 256K);
5) Task A executes btrfs_dio_iomap_begin() again, this time for the file
range [128K, 256K), and locks the file range [128K, 256K);
6) Task B starts a direct IO write against file range [0, 256K) as well.
It also locks the inode in shared mode, as it's within the i_size limit,
and then tries to lock file range [0, 256K). It is able to lock the
subrange [0, 128K) but then blocks waiting for the range [128K, 256K),
as it is currently locked by task A;
7) Task A enters btrfs_get_blocks_direct_write() and tries to reserve data
space. Because we are low on available free space, it triggers the
async data reclaim task, and waits for it to reserve data space;
8) The async reclaim task decides to wait for all existing ordered extents
to complete (through btrfs_wait_ordered_roots()).
It finds the ordered extent previously created by task A for the file
range [0, 128K) and waits for it to complete;
9) The ordered extent for the file range [0, 128K) can not complete
because it blocks at btrfs_finish_ordered_io() when trying to lock the
file range [0, 128K).
This results in a deadlock, because:
- task B is holding the file range [0, 128K) locked, waiting for the
range [128K, 256K) to be unlocked by task A;
- task A is holding the file range [128K, 256K) locked and it's waiting
for the async data reclaim task to satisfy its space reservation
request;
- the async data reclaim task is waiting for ordered extent [0, 128K)
to complete, but the ordered extent can not complete because the
file range [0, 128K) is currently locked by task B, which is waiting
on task A to unlock file range [128K, 256K) and task A waiting
on the async data reclaim task.
This results in a deadlock between 4 task: task A, task B, the async
data reclaim task and the task doing ordered extent completion (a work
queue task).
This type of deadlock can sporadically be triggered by the test case
generic/300 from fstests, and results in a stack trace like the following:
[12084.033689] INFO: task kworker/u16:7:123749 blocked for more than 241 seconds.
[12084.034877] Not tainted 5.18.0-rc2-btrfs-next-115 #1
[12084.035562] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[12084.036548] task:kworker/u16:7 state:D stack: 0 pid:123749 ppid: 2 flags:0x00004000
[12084.036554] Workqueue: btrfs-flush_delalloc btrfs_work_helper [btrfs]
[12084.036599] Call Trace:
[12084.036601] <TASK>
[12084.036606] __schedule+0x3cb/0xed0
[12084.036616] schedule+0x4e/0xb0
[12084.036620] btrfs_start_ordered_extent+0x109/0x1c0 [btrfs]
[12084.036651] ? prepare_to_wait_exclusive+0xc0/0xc0
[12084.036659] btrfs_run_ordered_extent_work+0x1a/0x30 [btrfs]
[12084.036688] btrfs_work_helper+0xf8/0x400 [btrfs]
[12084.036719] ? lock_is_held_type+0xe8/0x140
[12084.036727] process_one_work+0x252/0x5a0
[12084.036736] ? process_one_work+0x5a0/0x5a0
[12084.036738] worker_thread+0x52/0x3b0
[12084.036743] ? process_one_work+0x5a0/0x5a0
[12084.036745] kthread+0xf2/0x120
[12084.036747] ? kthread_complete_and_exit+0x20/0x20
[12084.036751] ret_from_fork+0x22/0x30
[12084.036765] </TASK>
[12084.036769] INFO: task kworker/u16:11:153787 blocked for more than 241 seconds.
[12084.037702] Not tainted 5.18.0-rc2-btrfs-next-115 #1
[12084.038540] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[12084.039506] task:kworker/u16:11 state:D stack: 0 pid:153787 ppid: 2 flags:0x00004000
[12084.039511] Workqueue: events_unbound btrfs_async_reclaim_data_space [btrfs]
[12084.039551] Call Trace:
[12084.039553] <TASK>
[12084.039557] __schedule+0x3cb/0xed0
[12084.039566] schedule+0x4e/0xb0
[12084.039569] schedule_timeout+0xed/0x130
[12084.039573] ? mark_held_locks+0x50/0x80
[12084.039578] ? _raw_spin_unlock_irq+0x24/0x50
[12084.039580] ? lockdep_hardirqs_on+0x7d/0x100
[12084.039585] __wait_for_common+0xaf/0x1f0
[12084.039587] ? usleep_range_state+0xb0/0xb0
[12084.039596] btrfs_wait_ordered_extents+0x3d6/0x470 [btrfs]
[12084.039636] btrfs_wait_ordered_roots+0x175/0x240 [btrfs]
[12084.039670] flush_space+0x25b/0x630 [btrfs]
[12084.039712] btrfs_async_reclaim_data_space+0x108/0x1b0 [btrfs]
[12084.039747] process_one_work+0x252/0x5a0
[12084.039756] ? process_one_work+0x5a0/0x5a0
[12084.039758] worker_thread+0x52/0x3b0
[12084.039762] ? process_one_work+0x5a0/0x5a0
[12084.039765] kthread+0xf2/0x120
[12084.039766] ? kthread_complete_and_exit+0x20/0x20
[12084.039770] ret_from_fork+0x22/0x30
[12084.039783] </TASK>
[12084.039800] INFO: task kworker/u16:17:217907 blocked for more than 241 seconds.
[12084.040709] Not tainted 5.18.0-rc2-btrfs-next-115 #1
[12084.041398] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[12084.042404] task:kworker/u16:17 state:D stack: 0 pid:217907 ppid: 2 flags:0x00004000
[12084.042411] Workqueue: btrfs-endio-write btrfs_work_helper [btrfs]
[12084.042461] Call Trace:
[12084.042463] <TASK>
[12084.042471] __schedule+0x3cb/0xed0
[12084.042485] schedule+0x4e/0xb0
[12084.042490] wait_extent_bit.constprop.0+0x1eb/0x260 [btrfs]
[12084.042539] ? prepare_to_wait_exclusive+0xc0/0xc0
[12084.042551] lock_extent_bits+0x37/0x90 [btrfs]
[12084.042601] btrfs_finish_ordered_io.isra.0+0x3fd/0x960 [btrfs]
[12084.042656] ? lock_is_held_type+0xe8/0x140
[12084.042667] btrfs_work_helper+0xf8/0x400 [btrfs]
[12084.042716] ? lock_is_held_type+0xe8/0x140
[12084.042727] process_one_work+0x252/0x5a0
[12084.042742] worker_thread+0x52/0x3b0
[12084.042750] ? process_one_work+0x5a0/0x5a0
[12084.042754] kthread+0xf2/0x120
[12084.042757] ? kthread_complete_and_exit+0x20/0x20
[12084.042763] ret_from_fork+0x22/0x30
[12084.042783] </TASK>
[12084.042798] INFO: task fio:234517 blocked for more than 241 seconds.
[12084.043598] Not tainted 5.18.0-rc2-btrfs-next-115 #1
[12084.044282] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[12084.045244] task:fio state:D stack: 0 pid:234517 ppid:234515 flags:0x00004000
[12084.045248] Call Trace:
[12084.045250] <TASK>
[12084.045254] __schedule+0x3cb/0xed0
[12084.045263] schedule+0x4e/0xb0
[12084.045266] wait_extent_bit.constprop.0+0x1eb/0x260 [btrfs]
[12084.045298] ? prepare_to_wait_exclusive+0xc0/0xc0
[12084.045306] lock_extent_bits+0x37/0x90 [btrfs]
[12084.045336] btrfs_dio_iomap_begin+0x336/0xc60 [btrfs]
[12084.045370] ? lock_is_held_type+0xe8/0x140
[12084.045378] iomap_iter+0x184/0x4c0
[12084.045383] __iomap_dio_rw+0x2c6/0x8a0
[12084.045406] iomap_dio_rw+0xa/0x30
[12084.045408] btrfs_do_write_iter+0x370/0x5e0 [btrfs]
[12084.045440] aio_write+0xfa/0x2c0
[12084.045448] ? __might_fault+0x2a/0x70
[12084.045451] ? kvm_sched_clock_read+0x14/0x40
[12084.045455] ? lock_release+0x153/0x4a0
[12084.045463] io_submit_one+0x615/0x9f0
[12084.045467] ? __might_fault+0x2a/0x70
[12084.045469] ? kvm_sched_clock_read+0x14/0x40
[12084.045478] __x64_sys_io_submit+0x83/0x160
[12084.045483] ? syscall_enter_from_user_mode+0x1d/0x50
[12084.045489] do_syscall_64+0x3b/0x90
[12084.045517] entry_SYSCALL_64_after_hwframe+0x44/0xae
[12084.045521] RIP: 0033:0x7fa76511af79
[12084.045525] RSP: 002b:00007ffd6d6b9058 EFLAGS: 00000246 ORIG_RAX: 00000000000000d1
[12084.045530] RAX: ffffffffffffffda RBX: 00007fa75ba6e760 RCX: 00007fa76511af79
[12084.045532] RDX: 0000557b304ff3f0 RSI: 0000000000000001 RDI: 00007fa75ba4c000
[12084.045535] RBP: 00007fa75ba4c000 R08: 00007fa751b76000 R09: 0000000000000330
[12084.045537] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000001
[12084.045540] R13: 0000000000000000 R14: 0000557b304ff3f0 R15: 0000557b30521eb0
[12084.045561] </TASK>
Fix this issue by always reserving data space before locking a file range
at btrfs_dio_iomap_begin(). If we can't reserve the space, then we don't
error out immediately - instead after locking the file range, check if we
can do a NOCOW write, and if we can we don't error out since we don't need
to allocate a data extent, however if we can't NOCOW then error out with
-ENOSPC. This also implies that we may end up reserving space when it's
not needed because the write will end up being done in NOCOW mode - in that
case we just release the space after we noticed we did a NOCOW write - this
is the same type of logic that is done in the path for buffered IO writes.
Fixes: f0bfa76a11 ("btrfs: fix ENOSPC failure when attempting direct IO write into NOCOW range")
CC: stable@vger.kernel.org # 5.17+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Derive the compression type from extent map as opposed to the bio flags
passed. This makes it more precise and not reliant on function
parameters.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[SUSPICIOUS CODE]
When refactoring scrub code, I noticed a very strange behavior around
scrub_remap_extent():
if (sctx->is_dev_replace)
scrub_remap_extent(fs_info, cur_logical, scrub_len,
&cur_physical, &target_dev, &cur_mirror);
As replace target is a 1:1 copy of the source device, thus physical
offset inside the target should be the same as physical inside source,
thus this remap call makes no sense to me.
[REAL FUNCTIONALITY]
After more investigation, the function name scrub_remap_extent()
doesn't tell anything of the truth, nor does its if () condition.
The real story behind this function is that, for scrub_pages() we never
expect missing device, even for replacing missing device.
What scrub_remap_extent() is really doing is to find a live mirror, and
make later scrub_pages() to read data from the good copy, other than
from the missing device and increase error counters unnecessarily.
[IMPROVEMENT]
We have no need to bother scrub_remap_extent() in scrub_simple_mirror()
at all, we only need to call it before we call scrub_pages().
And rename the function to scrub_find_live_copy(), add extra comments on
them.
By this we can remove one parameter from scrub_extent(), and reduce the
unnecessary calls to scrub_remap_extent() for regular replace.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Since we have find_first_extent_item() to iterate the extent items of a
certain range, there is no need to use the open-coded version.
Replace the final scrub call site with find_first_extent_item().
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Currently scrub_raid56_parity() has a large double loop, handling the
following things at the same time:
- Iterate each data stripe
- Iterate each extent item in one data stripe
Refactor this by:
- Introduce a new helper to handle data stripe iteration
The new helper is scrub_raid56_data_stripe_for_parity(), which
only has one while() loop handling the extent items inside the
data stripe.
The code is still mostly the same as the old code.
- Call cond_resched() for each extent
Previously we only call cond_resched() under a complex if () check.
I see no special reason to do that, and for other scrub functions,
like scrub_simple_mirror() we're already doing the same cond_resched()
after scrubbing one extent.
- Add more comments
Please note that, this patch is only to address the double loop, there
are incoming patches to do extra cleanup.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Although RAID56 has complex repair mechanism, which involves reading the
whole full stripe, but inside one data stripe, it's in fact no different
than SINGLE/RAID1.
The point here is, for data stripe we just check the csum for each
extent we hit. Only for csum mismatch case, our repair paths divide.
So we can still reuse scrub_simple_mirror() for RAID56 data stripes,
which saves quite some code.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Since we have moved all other profiles handling into their own
functions, now the main body of scrub_stripe() is just handling RAID56
profiles.
There is no need to address other profiles in the main loop of
scrub_stripe(), so we can remove those dead branches.
Since we're here, also slightly change the timing of initialization of
variables like @offset, @increment and @logical.
Especially for @logical, we don't really need to initialize it for
btrfs_extent_root()/btrfs_csum_root(), we can use bg->start for that
purpose.
Now those variables are only initialize for RAID56 branches.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The new entrance will iterate through each data stripe which belongs to
the target device.
And since inside each data stripe, RAID0 is just SINGLE, while RAID10 is
just RAID1, we can reuse scrub_simple_mirror() to do the scrub properly.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The new helper, scrub_simple_mirror(), will scrub all extents inside a
range which only has simple mirror based duplication.
This covers every range of SINGLE/DUP/RAID1/RAID1C*, and inside each
data stripe for RAID0/RAID10.
Currently we will use this function to scrub SINGLE/DUP/RAID1/RAID1C*
profiles. As one can see, the new entrance for those simple-mirror
based profiles can be small enough (with comments, just reach 100
lines).
This function will be the basis for the incoming scrub refactor.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The new helper, find_first_extent_item(), will locate an extent item
(either EXTENT_ITEM or METADATA_ITEM) which covers any byte of the
search range.
This helper will later be used to refactor scrub code.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The variable @physical_end is the exclusive stripe end, currently it's
calculated using @physical + @dev_extent_len / map->stripe_len *
map->stripe_len.
And since at allocation time we ensured dev_extent_len is stripe_len
aligned, the result is the same as @physical + @dev_extent_len.
So this patch will just assign @physical and @physical_end early,
without using @nstripes.
This is especially helpful for any possible out: label user, as now we
only need to initialize @offset before going to out: label.
Since we're here, also make @physical_end constant.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
… rename it to simply fs_roots and adjust all usages of this object to use
the XArray API, because it is notionally easier to use and understand, as
it provides array semantics, and also takes care of locking for us,
further simplifying the code.
Also do some refactoring, esp. where the API change requires largely
rewriting some functions, anyway.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Gabriel Niebler <gniebler@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
… named 'extent_buffers'. Also adjust all usages of this object to use
the XArray API, which greatly simplifies the code as it takes care of
locking and is generally easier to use and understand, providing
notionally simpler array semantics.
Also perform some light refactoring.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Gabriel Niebler <gniebler@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
… and adjust all usages of this object to use the XArray API for the sake
of consistency.
XArray API provides array semantics, so it is notionally easier to use and
understand, and it also takes care of locking for us.
None of this makes a real difference in this particular patch, but it does
in other places where similar replacements are or have been made and we
want to be consistent in our usage of data structures in btrfs.
Signed-off-by: Gabriel Niebler <gniebler@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
… in the btrfs_root struct and adjust all usages of this object to use
the XArray API, because it is notionally easier to use and understand,
as it provides array semantics, and also takes care of locking for us,
further simplifying the code.
Also use the opportunity to do some light refactoring.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Gabriel Niebler <gniebler@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
In function btrfs_bg_flags_to_raid_index(), we use quite some if () to
convert the BTRFS_BLOCK_GROUP_* bits to a index number.
But the truth is, there is really no such need for so many branches at
all.
Since all BTRFS_BLOCK_GROUP_* flags are just one single bit set inside
BTRFS_BLOCK_GROUP_PROFILES_MASK, we can easily use ilog2() to calculate
their values.
This calculation has an anchor point, the lowest PROFILE bit, which is
RAID0.
Even it's fixed on-disk format and should never change, here I added
extra compile time checks to make it super safe:
1. Make sure RAID0 is always the lowest bit in PROFILE_MASK
This is done by finding the first (least significant) bit set of
RAID0 and PROFILE_MASK & ~RAID0.
2. Make sure RAID0 bit set beyond the highest bit of TYPE_MASK
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It's only internally used as another way to represent btrfs profiles,
it's not exposed through any on-disk format, in fact this
btrfs_raid_types is diverted from the on-disk format values.
Furthermore, since it's internal structure, its definition can change in
the future.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
rmw_workers doesn't need ordered execution or thread disabling threshold
(as the thresh parameter is less than DFT_THRESHOLD).
Just switch to the normal workqueues that use a lot less resources,
especially in the work_struct vs btrfs_work structures.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
All three scrub workqueues don't need ordered execution or thread
disabling threshold (as the thresh parameter is less than DFT_THRESHOLD).
Just switch to the normal workqueues that use a lot less resources,
especially in the work_struct vs btrfs_work structures.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Just let the one caller that wants optional WQ_HIGHPRI handling allocate
a separate btrfs_workqueue for that. This allows to rename struct
__btrfs_workqueue to btrfs_workqueue, remove a pointer indirection and
separate allocation for all btrfs_workqueue users and generally simplify
the code.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now the btrfs RAID56 infrastructure has migrated to use sector_ptr
interface, it should be safe to enable subpage support for RAID56.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The non-compatible part is only the bitmap iteration part, now the
bitmap size is extended to rbio::stripe_nsectors, not the old
rbio::stripe_npages.
Since we're here, also slightly improve the function by:
- Rename @i to @stripe
- Rename @bit to @sectornr
- Move @page and @index into the inner loop
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Function steal_rbio() will take all the uptodate pages from the source
rbio to destination rbio.
With the new stripe_sectors[] array, we also need to do the extra check:
- Check sector::flags to make sure the full page is uptodate
Now we don't use PageUptodate flag for subpage cases to indicate
if the page is uptodate.
Instead we need to check all the sectors belong to the page to be sure
about whether it's full page uptodate.
So here we introduce a new helper, full_page_sectors_uptodate() to do
the check.
- Update rbio::stripe_sectors[] to use the new page pointer
We only need to change the page pointer, no need to change anything
else.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Unlike previous code, we can not directly set PageUptodate for stripe
pages now. Instead we have to iterate through all the sectors and set
SECTOR_UPTODATE flag there.
Introduce a new helper find_stripe_sector(), to do the work.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The functionality is completely replaced by the new bio_sectors member,
now it's time to remove the old member.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This requires one extra parameter @pgoff for the function.
In the current code base, scrub is still one page per sector, thus the
new parameter will always be 0.
It needs the extra subpage scrub optimization code to fully take
advantage.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There is only one caller for that helper now, and we're definitely fine
to open-code it.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
With this function converted to subpage compatible sector interfaces,
the following helper functions can be removed:
- rbio_stripe_page()
- rbio_pstripe_page()
- rbio_qstripe_page()
- page_in_rbio()
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This involves:
- Use sector_ptr interface to grab the pointers
- Add sector->pgoff to pointers[]
- Rebuild data using sectorsize instead of PAGE_SIZE
- Use memcpy() to replace copy_page()
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The core is to convert direct page usage into sector_ptr usage, and
use memcpy() to replace copy_page().
For pointers usage, we need to convert it to kmap_local_page() +
sector->pgoff.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Make rbio_add_io_page() subpage compatible, which involves:
- Rename rbio_add_io_page() to rbio_add_io_sector()
Although we still rely on PAGE_SIZE == sectorsize, so add a new
ASSERT() inside rbio_add_io_sector() to make sure all pgoff is 0.
- Introduce rbio_stripe_sector() helper
The equivalent of rbio_stripe_page().
This new helper has extra ASSERT()s to validate the stripe and sector
number.
- Introduce sector_in_rbio() helper
The equivalent of page_in_rbio().
- Rename @pagenr variables to @sectornr
- Use rbio::stripe_nsectors when iterating the bitmap
Please note that, this only changes the interface, the bios are still
using full page for IO.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
