[Why]
ABM 2.3 firmware expects information in iRAM that differs from previous
versions of ABM, so a mechanism is required to provide it with that
information.
[How]
Extend the existing iRAM definition to include parameters added by
ABM 2.3, and load it if DMCU is running ABM 2.3.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
With Scatter Gather enabled, HUBP underflows during MPO enabled video
playback. hubp_init has a register write that fixes this problem, but
the register is cleared when HUBP gets power gated.
[how]
Make a call to hubp_init during enable_plane, so that the fix can
be applied after HUBP powers back on again.
Signed-off-by: Zi Yu Liao <ziyu.liao@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Disable_audio_stream gets enum option as a paramenter which will decide
if we free acquired resources or not. However checks for the option is
guarded by the other condition which check if audio stream is getting
diabled more than once. With both conditions combined, if we attempt to
disable audio stream twice in a row, first with keep and second with
free as an option, we will never free any resources, which will make
system think there is audio endpoint connected even after we plug out
the device
[How]
Get rid of option as parameter to disable_audio_stream and move the part
of the code that free acquired resources to outside where to keep or to
free resources is actually determined
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dig_encoder_sel_to_atom will always return zero on any ASIC version
past DCE80 since programming of the FE selection is handled by
driver, but the translation code was left in the function, making
it look like a coding error.
[How]
Remove code that has no effect, and replace with a comment describing
why it returns zero.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently odm is handled using top_bottom pipe by special casing
the differing opps to differentiate from mpc combine.
Since top/bottom pipe list was made to track mpc muxing this creates
difficulties in adding a 4 pipe odm case support.
Rather than continue using mpc combine list, this change reworks odm
to use it's own linked list to keep track of odm combine pipes. This
also opens up options for using mpo with odm, if a practical use case
is ever found.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So that we properly handle them on older asics.
Fixes: 3ff985485b ("drm/amdgpu: Export function to flush TLB of specific vm hub")
Tested-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a dcfeaturemask flag for mclk switching. Disable by default;
enable once the feature has seen more testing.
Set amdgpu.dcfeaturemask=2 on the kernel command line in grub
to enable this.
Acked-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Properly set all_displays_in_sync so that when the data is
propagated to powerplay, it's set properly and we can enable
mclk switching when all monitors are in sync.
v2: fix logic, clean up
v3: check for blending chains, simplify logic
Acked-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If DC has synced the displays, we can enable mclk switching to
save power.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If DC has synced the displays, we can enable mclk switching to
save power.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For the 40.46 SMU release, they changed CurrSocketPower to
AverageSocketPower, but this was changed back in 40.47 so just check if
it's 40.46 and make the appropriate change
Tested with 40.45, 40.46 and 40.47 successfully
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add the virtual function PCI device id.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Frank.Min <Frank.Min@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
fix other navi asic set peak performance level error.
because the navi10_ppt.c will handle navi12 14 asic,
it will use navi10 peak value to set other asic, it is not correct.
after patch:
only navi10 use custom peak value, other asic will used default value.
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use unsigned long type for the same ras count variable.
This will avoid overflow on 64 bit system.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: zhong jiang <zhongjiang@huawei.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190613115749.GC26335@kroah.com
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704023557.4551-1-huangfq.daxian@gmail.com
Some, mostly Fermi, vbioses appear to have zero max voltage. That causes Nouveau to not parse voltage entries, thus users not being able to set higher clocks.
When changing this value Nvidia driver still appeared to ignore it, and I wasn't able to find out why, thus the code is ignoring the value if it is zero.
CC: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Mark Menzynski <mmenzyns@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This is something that got noticed a while ago back when I was fixing a
large number of runtime PM related issues in nouveau, but never got
fixed:
https://patchwork.freedesktop.org/series/46815/#rev7
It's not safe to iterate the entire list of CRTCs in
nv50_disp_atomic_commit(), as we could be doing a non-blocking modeset
on one CRTC in parallel with one or more other CRTCs. Likewise, this
means it's also not safe to do so in order to track runtime PM state.
While this code is certainly wrong, so far the only issues I've seen
this cause in the wild is the occasional PM ref unbalance after an
atomic check failure + module reloading (since the PCI device will
outlive nouveau in such scenarios).
So, do this far more elegantly: grab a runtime PM ref across the modeset
and commit tail, then grab/put references for each CRTC enable/disable.
This also ends up being much simpler then the previous broken solution
we had.
Finally, since we've removed all it's users: get rid of
nouveau_drm->have_disp_power_ref.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Originally when trying to fix the issue of runtime PM references with
non-blocking CRTCs on nv50, I ended up stumbling on this code when
trying to remove nouveau_drm->have_disp_power_ref, and attempted to fix
it to remove the dependency on have_disp_power_ref. However, Ilia Mirkin
pointed out that this code is actually completely useless, as pre-nv50
never had runtime PM support in the first place! Go figure.
So, since it's useless just get rid of it. Note that since the only
thing nouveau_crtc_set_config() was doing was grabbing a runtime PM ref,
calling drm_crtc_helper_set_config() then dropping the ref; we can just
remove the function entirely and just call drm_crtc_helper_set_config()
directly.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Added GPIO is "Power Alert". It's uncertain if this
GPIO is set on GPU initialization or only if a change is detected by the
GPU at runtime.
This GPIO can be found on Tesla and sometimes on Fermi GPUs.
Untested, wrote according to documentation.
Signed-off-by: Mark Menzynski <mmenzyns@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Added GPIO is "Thermal and External Power Detect". It's uncertain if this
GPIO is set on GPU initialization or only if a change is detected by the
GPU at runtime.
This GPIO can be found in Rankine and Curie and rarely on Tesla GPUs
VBIOS.
Untested, wrote according to documentation.
Signed-off-by: Mark Menzynski <mmenzyns@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Currently, nouveau doesn't check if GPU is missing power. This
patch makes nouveau fail when this happens on latest GPUs.
It checks GPIO function 121 (External Power Emergency), which
should detect power problems on GPU initialization.
This can be disabled with nouveau.config=NvPowerChecks=1
Tested on TU104, GP106 and GF100.
v3:
* Add config override for disabling power checks
Signed-off-by: Mark Menzynski <mmenzyns@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
One gpio was in wrong place, moved it for better readability.
Signed-off-by: Mark Menzynski <mmenzyns@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's already a condition in place which attempts to detect this, but
since we've begun to require a PMU subdev even on boards where we don't
load a custom FW, it's become inaccurate.
This will prevent unnecessarily running a periodic fan update thread on
GP100 and newer, where we don't yet override the default PMU FW.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Has a nice side-effect that we only update HW for this when it changes now,
rather than every time we do a page flip.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
zpos normalisation uses plane id to determine ordering for duplicate zpos
values, and we likely want to keep primary plane on the bottom here.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We have some of this open-coded already, use the helper to prevent problems
when adding (for example) support for the alpha property.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
For GF119:GV100, we can enable DEGAMMA/CTM/GAMMA. For earlier GPUs, as
there is no CTM, having both degamma and gamma is a bit pointless. Later
GPUs currently lack an implementation.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The overlay logic can only do colorkey-based selection, not
alpha-blending.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Pascal was particularly incorrect, as the register changed to be more in the
same format as the MMU fault buffers are.
Shouldn't have impacted much more than confusing MMU fault log messages.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Would like to be able to reuse gf100_fifo_intr_fault() for (some of) the
later chipsets too, as it's identical.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signal that the reset sequence has completed.
This opcode signals that the software reset sequence has completed.
Ordinarily, no actual operations are performed by the opcode.
However it allows for possible software work arounds by devinit
engines in software agents other than the VBIOS, such as the resman,
FCODE, and EFI driver.
Signed-off-by: Rhys Kidd <rhyskidd@gmail.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signal that the reset sequence has begun.
This opcode signals that the software reset sequence has begun.
Ordinarily, no actual operations are performed by the opcode.
However it allows for possible software work arounds by devinit
engines in software agents other than the VBIOS, such as the resman,
FCODE, and EFI driver.
Signed-off-by: Rhys Kidd <rhyskidd@gmail.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Absence of a TMDS Info Table is common on Optimus setups where the NVIDIA
gpu is not connected directly to any outputs.
Reporting an error in this scenario is too harsh. Accordingly, change the
error message to an info message.
By default the error message also causes a boot flicker for these sytems.
Signed-off-by: Rhys Kidd <rhyskidd@gmail.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We now have per-device driver_features, so let's use that
to disable atomic only for pre-nv50.
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: nouveau@lists.freedesktop.org
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Older hardware seems to want 0..1024 values, while new hardware takes
0..1 values. We set the gain to 1024 for the earlier display classes.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On Turing, an input LUT is required to transform inputs in fixed-point
formats to FP16 for the internal display pipe. We provide an identity
mapping whenever a window is enabled for this reason.
HW has error checks to ensure when the input is already FP16, that the
input LUT is also disabled.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, replace the following form:
sizeof(*kind) + sizeof(*kind->data) * mmu->kind_nr;
with:
struct_size(kind, data, mmu->kind_nr)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
