Add structures, identifiers, and helper functions for several AdminQ
commands related to performing a firmware update for the ice hardware.
These will be used in future code for implementing the devlink
.flash_update handler.
Signed-off-by: Cudzilo, Szymon T <szymon.t.cudzilo@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extends function parsing response from Discover Device
Capability AQC to check if the device supports unified NVM update flow.
Signed-off-by: Jacek Naczyk <jacek.naczyk@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pldmfw library is used to implement common logic needed to flash
devices based on firmware files using the format described by the PLDM
for Firmware Update standard.
This library consists of logic to parse the PLDM file format from
a firmware file object, as well as common logic for sending the relevant
PLDM header data to the device firmware.
A simple ops table is provided so that device drivers can implement
device specific hardware interactions while keeping the common logic to
the pldmfw library.
This library will be used by the Intel ice networking driver as part of
implementing device flash update via devlink. The library aims to be
vendor and device agnostic. For this reason, it has been placed in
lib/pldmfw, in the hopes that other devices which use the PLDM firmware
file format may benefit from it in the future. However, do note that not
all features defined in the PLDM standard have been implemented.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify mtk_gmac0_rgmii_adjust() so it can always be called.
mtk_gmac0_rgmii_adjust() sets-up the TRGMII clocks.
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-By: David Woodhouse <dwmw2@infradead.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mat Martineau says:
====================
mptcp: Exchange MPTCP DATA_FIN/DATA_ACK before TCP FIN
This series allows the MPTCP-level connection to be closed with the
peers exchanging DATA_FIN and DATA_ACK according to the state machine in
appendix D of RFC 8684. The process is very similar to the TCP
disconnect state machine.
The prior code sends DATA_FIN only when TCP FIN packets are sent, and
does not allow for the MPTCP-level connection to be half-closed.
Patch 8 ("mptcp: Use full MPTCP-level disconnect state machine") is the
core of the series. Earlier patches in the series have some small fixes
and helpers in preparation, and the final four small patches do some
cleanup.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPTCP socket's write_seq member can be read without the msk lock
held, so use WRITE_ONCE() to store it.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPTCP socket's write_seq member should be read with READ_ONCE() when
the msk lock is not held.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bare TCP ack skbs are freed right after MPTCP sees them, so the work to
allocate, zero, and populate the MPTCP skb extension is wasted. Detect
these skbs and do not add skb extensions to them.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPTCP state machine handles disconnections on non-fallback connections,
but the mptcp_sock still needs to get notified when fallback subflows
disconnect.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 8684 appendix D describes the connection state machine for
MPTCP. This patch implements the DATA_FIN / DATA_ACK exchanges and
MPTCP-level socket state changes described in that appendix, rather than
simply sending DATA_FIN along with TCP FIN when disconnecting subflows.
DATA_FIN is now sent and acknowledged before shutting down the
subflows. Received DATA_FIN information (if not part of a data packet)
is written to the MPTCP socket when the incoming DSS option is parsed by
the subflow, and the MPTCP worker is scheduled to process the
flag. DATA_FIN received as part of a full DSS mapping will be handled
when the mapping is processed.
The DATA_FIN is acknowledged by the worker if the reader is caught
up. If there is still data to be moved to the MPTCP-level queue, ack_seq
will be incremented to account for the DATA_FIN when it reaches the end
of the stream and a DATA_ACK will be sent to the peer.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After DATA_FIN has been sent, the peer will acknowledge it. An ack of
the relevant MPTCP-level sequence number will update the MPTCP
connection state appropriately.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used to transition to the appropriate state on close and
determine if a DATA_FIN needs to be sent for that state transition.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incoming DATA_FIN headers need to propagate the presence of the DATA_FIN
bit and the associated sequence number to the MPTCP layer, even when
arriving on a bare ACK that does not get added to the receive queue. Add
structure members to store the DATA_FIN information and helpers to set
and check those values.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since DATA_FIN information is the same for every subflow, store it only
in the mptcp_sock.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mptcp_close() acquires the msk lock, so it clearly should not be held
before the function is called.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A MPTCP socket where sending has been shut down should not attempt to
send additional data, since DATA_FIN has already been sent.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 8684-compliant DATA_FIN needs to be sent and ack'd before subflows
are closed with TCP FIN, so write DATA_FIN DSS headers whenever their
transmission has been enabled by the MPTCP connection-level socket.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl8ggswACgkQSD+KveBX
+j7yOgf8DjzPtSpVfUA7Iq28WO6YxJy208oUdLjKNuRNr74vXulHegNlP6cFDHU3
QIddvTBNMTp2BpJpoFMbEod7sVTBq5KVQZvpIuFM2JU4h76vL4cYbWeBuT6rFIoJ
m5vuuUyAB+16QbJzagY/rqfQMs0w7KnR+Zhv18JzwyHhBiRLaPzYdmSWM2kkF8HZ
3DrY8RWgkeaI9vTpE6Fau7BRNDUOMgjIahiUrojJuyPsYZpJf5g+KaMj4xvgcqMa
vaPaw8iHN7+N3KIdcf6MJhfzx3SHP5YNieU/MfvE9sLvdPvfLETdpexYPB8b0/vs
L9w2D8j0uZyXek30fIiIwHaibQGZPw==
=W0Fn
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2020-07-28' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes-2020-07-28
This series introduces some fixes to mlx5 driver.
v1->v2:
- Drop the "Hold reference on mirred devices" patch, until Or's
comments are addressed.
- Imporve "Modify uplink state" patch commit message per Or's request.
Please pull and let me know if there is any problem.
For -Stable:
For -stable v4.9
('net/mlx5e: Fix error path of device attach')
For -stable v4.15
('net/mlx5: Verify Hardware supports requested ptp function on a given
pin')
For -stable v5.3
('net/mlx5e: Modify uplink state on interface up/down')
For -stable v5.4
('net/mlx5e: Fix kernel crash when setting vf VLANID on a VF dev')
('net/mlx5: E-switch, Destroy TSAR when fail to enable the mode')
For -stable v5.5
('net/mlx5: E-switch, Destroy TSAR after reload interface')
For -stable v5.7
('net/mlx5: Fix a bug of using ptp channel index as pin index')
====================
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Hellwig says:
====================
sockptr_t fixes v2
a bunch of fixes for the sockptr_t conversion
Changes since v1:
- fix a user pointer dereference braino in bpfilter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure not just the pointer itself but the whole range lies in
the user address space. For that pass the length and then use
the access_ok helper to do the check.
Fixes: 6d04fe15f7 ("net: optimize the sockptr_t for unified kernel/user address spaces")
Reported-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
sockptr_advance never properly worked. Replace it with _offset variants
of copy_from_sockptr and copy_to_sockptr.
Fixes: ba423fdaa5 ("net: add a new sockptr_t type")
Reported-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reported-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jason A. Donenfeld <Jason@zx2c4.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the kernel in general is not strict aliasing safe we can trivially
do that in sockptr_is_null without affecting code generation, so always
check the actually assigned union member.
Reported-by: Jan Engelhardt <jengelh@inai.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was accidentally removed in an unrelated commit.
Fixes: c2f12630c6 ("netfilter: switch nf_setsockopt to sockptr_t")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hovold says:
====================
net: lan78xx: fix NULL deref and memory leak
The first two patches fix a NULL-pointer dereference at probe that can
be triggered by a malicious device and a small transfer-buffer memory
leak, respectively.
For another subsystem I would have marked them:
Cc: stable@vger.kernel.org # 4.3
The third one replaces the driver's current broken endpoint lookup
helper, which could end up accepting incomplete interfaces and whose
results weren't even useeren
Johan
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the bogus endpoint-lookup helper which could end up accepting
interfaces based on endpoints belonging to unrelated altsettings.
Note that the returned bulk pipes and interrupt endpoint descriptor
were never actually used. Instead the bulk-endpoint numbers are
hardcoded to 1 and 2 (matching the specification), while the interrupt-
endpoint descriptor was assumed to be the third descriptor created by
USB core.
Try to bring some order to this by dropping the bogus lookup helper and
adding the missing endpoint sanity checks while keeping the interrupt-
descriptor assumption for now.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt URB transfer-buffer was never freed on disconnect or after
probe errors.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing endpoint sanity check to prevent a NULL-pointer
dereference should a malicious device lack the expected endpoints.
Note that the driver has a broken endpoint-lookup helper,
lan78xx_get_endpoints(), which can end up accepting interfaces in an
altsetting without endpoints as long as *some* altsetting has a bulk-in
and a bulk-out endpoint.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Add support for QSFP-DD transceiver type
This patch set from Vadim adds support for Quad Small Form Factor
Pluggable Double Density (QSFP-DD) modules in mlxsw.
Patch #1 enables dumping of QSFP-DD module information through ethtool.
Patch #2 enables reading of temperature thresholds from QSFP-DD modules
for hwmon and thermal zone purposes.
Changes since v1 [1]:
Only rebase on top of net-next. After discussing with Andrew and Adrian
we agreed that current approach is OK and that in the future we can
follow Andrew's suggestion to "make a new API where user space can
request any pages it want, and specify the size of the page". This
should allow us "to work around known issues when manufactures get their
EEPROM wrong".
[1] https://lore.kernel.org/netdev/20200626144724.224372-1-idosch@idosch.org/#t
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow QSFP-DD transceivers temperature thresholds reading for hardware
monitoring and thermal control.
For this type, the thresholds are located in page 02h according to the
"Module and Lane Thresholds" description from Common Management
Interface Specification.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Quad Small Form Factor Pluggable Double Density (QSFP-DD) hardware
specification defines a form factor that supports up to 400 Gbps in
aggregate over an 8x50-Gbps electrical interface. The QSFP-DD supports
both optical and copper interfaces.
Implementation is based on Common Management Interface Specification;
Rev 4.0 May 8, 2019. Table 8-2 "Identifier and Status Summary (Lower
Page)" from this spec defines "Id and Status" fields located at offsets
00h - 02h. Bit 2 at offset 02h ("Flat_mem") specifies QSFP EEPROM memory
mode, which could be "upper memory flat" or "paged". Flat memory mode is
coded "1", and indicates that only page 00h is implemented in EEPROM.
Paged memory is coded "0" and indicates that pages 00h, 01h, 02h, 10h
and 11h are implemented. Pages 10h and 11h are currently not supported
by the driver.
"Flat" memory mode is used for the passive copper transceivers. For this
type only page 00h (256 bytes) is available. "Paged" memory is used for
the optical transceivers. For this type pages 00h (256 bytes), 01h (128
bytes) and 02h (128 bytes) are available. Upper page 01h contains static
advertising field, while upper page 02h contains the module-defined
thresholds and lane-specific monitors.
Extend enumerator 'mlxsw_reg_mcia_eeprom_module_info_id' with additional
field 'MLXSW_REG_MCIA_EEPROM_MODULE_INFO_TYPE_ID'. This field is used to
indicate for QSFP-DD transceiver type which memory mode is to be used.
Expose 256 bytes buffer for QSFP-DD passive copper transceiver and
512 bytes buffer for optical.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Misc and small update to mlx5 driver:
1) Aya adds PCIe relaxed ordering support for mlx5 netdev queues.
2) Eran Refactors pages data base to be per vf/function to speedup
unload time.
3) Parav changes eswitch steering initialization to account for
tota_vports rather than for only active vports and
Link non uplink representors to PCI device, for uniform naming scheme.
4) Tariq, trivial RX code improvements and missing inidirect calls
wrappers.
5) Small cleanup patches
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl8f8fgACgkQSD+KveBX
+j5pgggAtjGZ3dWt43WNIMEYum/OZYrIhAVIaB4IgPY2Q90i26A7VMpBUOpQxTzk
Z+PYiSuiwplWeQ0k9GW2yMCAEACsuiSQXQG/eUA4jKRKf9hQEXi5guuVEIYJRm68
uL4aI4m4Aygx/n2UTdajARB69RVZ02ZhoNucMGETw4gzvqLdSgVCyR2tiDnPiKKW
3+y9nViglik7XqvDrYT9H+7vo8geCg5zBWEABy/Ls0VUCWN2xCjPNbGL9VCMG8Q+
A6n5SdhaOMIc9u5vkcE4CVgOnUPwNPQeu+GVgEodZ7GhFwX897A8dvFwljfML/UU
rBRPgC2kUTtGDZxVcSBMlBjrXl6zMQ==
=iwh/
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2020-07-28' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-07-28
Misc and small update to mlx5 driver:
1) Aya adds PCIe relaxed ordering support for mlx5 netdev queues.
2) Eran Refactors pages data base to be per vf/function to speedup
unload time.
3) Parav changes eswitch steering initialization to account for
tota_vports rather than for only active vports and
Link non uplink representors to PCI device, for uniform naming scheme.
4) Tariq, trivial RX code improvements and missing inidirect calls
wrappers.
5) Small cleanup patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The .suspend() and .resume() callbacks are not defined for this driver.
Still, their power management structure follows the legacy framework. To
bring it under the generic framework, simply remove the binding of
callbacks from "struct pci_driver".
Change code indentation from space to tab in "struct pci_driver".
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting the PF interface up/down, notify the firmware to update
uplink state via MODIFY_VPORT_STATE, when E-Switch is enabled.
This behavior will prevent sending traffic out on uplink port when PF is
down, such as sending traffic from a VF interface which is still up.
Currently when calling mlx5e_open/close(), the driver only sends PAOS
command to notify the firmware to set the physical port state to
up/down, however, it is not sufficient. When VF is in "auto" state, it
follows the uplink state, which was not updated on mlx5e_open/close()
before this patch.
When switchdev mode is enabled and uplink representor is first enabled,
set the uplink port state value back to its FW default "AUTO".
Fixes: 63bfd399de ("net/mlx5e: Send PAOS command on interface up/down")
Signed-off-by: Ron Diskin <rondi@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In a special configuration, a ConnectX6-Dx pin pps-out might be activated
when driver is loaded. Fix the driver to always read the operational pin
mode when registering it, and advertise it accordingly.
Fixes: ee7f12205a ("net/mlx5e: Implement 1PPS support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5e_rep_is_lag_netdev is used as first check as part of netdev events
handler for bond device of non-uplink representors, this handler can get
any netdevice under the same network namespace of mlx5e netdevice. Current
code treats the netdev as mlx5e netdev and only later on verifies this,
hence causes the following Kasan trace:
[15402.744990] ==================================================================
[15402.746942] BUG: KASAN: slab-out-of-bounds in mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core]
[15402.749009] Read of size 8 at addr ffff880391f3f6b0 by task ovs-vswitchd/5347
[15402.752065] CPU: 7 PID: 5347 Comm: ovs-vswitchd Kdump: loaded Tainted: G B O --------- -t - 4.18.0-g3dcc204d291d-dirty #1
[15402.755349] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
[15402.757600] Call Trace:
[15402.758968] dump_stack+0x71/0xab
[15402.760427] print_address_description+0x6a/0x270
[15402.761969] kasan_report+0x179/0x2d0
[15402.763445] ? mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core]
[15402.765121] mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core]
[15402.766782] mlx5e_rep_esw_bond_netevent+0x129/0x620 [mlx5_core]
Fix by deferring the violating access to be post the netdev verify check.
Fixes: 7e51891a23 ("net/mlx5e: Use netdev events to set/del egress acl forward-to-vport rule")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix a bug where driver did not verify Hardware pin capabilities for
PTP functions.
Fixes: ee7f12205a ("net/mlx5e: Implement 1PPS support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On PTP mlx5_ptp_enable(on=0) flow, driver mistakenly used channel index
as pin index.
After ptp patch marked in fixes tag was introduced, driver can freely
call ptp_find_pin() as part of the .enable() callback.
Fix driver mlx5_ptp_enable(on=0) flow to always use ptp_find_pin(). With
that, Driver will use the correct pin index in mlx5_ptp_enable(on=0) flow.
In addition, when initializing the pins, always set channel to zero. As
all pins can be attached to all channels, let ptp_set_pinfunc() to move
them between the channels.
For stable branches, this fix to be applied only on kernels that includes
both patches in fixes tag. Otherwise, mlx5_ptp_enable(on=0) will be stuck
on pincfg_mux.
Fixes: 62582a7ee7 ("ptp: Avoid deadlocks in the programmable pin code.")
Fixes: ee7f12205a ("net/mlx5e: Implement 1PPS support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The cited commit add initialization of ethtool steering during
representor rx initializations without cleaning it up in representor
rx cleanup, this may cause for stale ethtool flows to remain after
moving back from switchdev mode to legacy mode.
Fixed by calling ethtool steering cleanup during rep rx cleanup.
Fixes: 6783e8b29f ("net/mlx5e: Init ethtool steering for representors")
Signed-off-by: Maor Dickman <maord@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On failure to attach the netdev, fix the rollback by re-setting the
device's state back to MLX5E_STATE_DESTROYING.
Failing to attach doesn't stop statistics polling via .ndo_get_stats64.
In this case, although the device is not attached, it falsely continues
to query the firmware for counters. Setting the device's state back to
MLX5E_STATE_DESTROYING prevents the firmware counters query.
Fixes: 26e59d8077 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The steering tree is as follow (nic RX as example):
---------
|root_ns|
---------
|
--------------------------------
| | |
---------- ---------- ---------
|p(prio)0| | p1 | | pn |
---------- ---------- ---------
| |
---------------- ---------------
|ns(e.g bypass)| |ns(e.g. lag) |
---------------- ---------------
| | |
---- ---- ----
|p0| |p1| |pn|
---- ---- ----
|
----
|FT|
----
find_next_chained_ft(prio) returns the first flow table in the next
priority. If prio is a parent of a flow table then it returns the first
flow table in the next priority in the same namespace, else if prio
is parent of namespace, then it should return the first flow table
in the next namespace. Currently if the user requests to forward to
next namespace, the code calls to find_next_chained_ft with the prio
of the next namespace and not the prio of the namesapce itself.
Fixes: 9254f8ed15 ("net/mlx5: Add support in forward to namespace")
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When eswitch offloads is enabled, TSAR is created before reloading
the interfaces.
However when eswitch offloads mode is disabled, TSAR is disabled before
reloading the interfaces.
To keep the eswitch enable/disable sequence as mirror, destroy TSAR
after reloading the interfaces.
Fixes: 1bd27b11c1 ("net/mlx5: Introduce E-switch QoS management")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When either esw_legacy_enable() or esw_offloads_enable() fails,
code missed to destroy the created TSAR.
Hence, add the missing call to destroy the TSAR.
Fixes: 610090ebce ("net/mlx5: E-switch, Initialize TSAR Qos hardware block before its user vports")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Huazhong Tan says:
====================
net: hns3: fixes for -net
There are some bugfixes for the HNS3 ethernet driver. patch#1 fixes
a desc filling bug, patch#2 fixes a false TX timeout issue, and
patch#3~#5 fixes some bugs related to VLAN and FD.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When device is resetting or reset failed, firmware is unable to
handle mailbox. VLAN should not be configured in this case.
Fixes: fe4144d47e ("net: hns3: sync VLAN filter entries when kill VLAN ID failed")
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user had created a FD rule, all the aRFS rules should be clear up.
HNS3 process flow as below:
1.get spin lock of fd_ruls_list
2.clear up all aRFS rules
3.release lock
4.get spin lock of fd_ruls_list
5.creat a rules
6.release lock;
There is a short period of time between step 3 and step 4, which would
creatting some new aRFS FD rules if driver was receiving packet.
So refactor the fd_rule_lock to fix it.
Fixes: 4412288757 ("net: hns3: refine the flow director handle")
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently hclgevf_update_port_base_vlan_info() may be called when
VF is resetting, which may cause hns3_nic_net_open() being called
twice unexpectedly.
So fix it by adding a reset check for it, and extend critical
region for rntl_lock in hclgevf_update_port_base_vlan_info().
Fixes: 92f11ea177 ("net: hns3: fix set port based VLAN issue for VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the queue depth and queue parameters are modified, there is
a low probability that TX timeout occurs. The two operations cause
the link to be down or up when the watchdog is still working. All
queues are stopped when the link is down. After the carrier is on,
all queues are woken up. If the watchdog detects the link between
the carrier on and wakeup queues, a false TX timeout occurs.
So fix this issue by modifying the sequence of carrier on and queue
wakeup, which is symmetrical to the link down action.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The linear and frag data part may be changed when the skb is expanded
or lineared in skb_cow_head() or skb_checksum_help(), which is called
by hns3_fill_skb_desc(), so the linear len return by skb_headlen()
before the calling of hns3_fill_skb_desc() is unreliable.
Move hns3_fill_skb_desc() before the calling of skb_headlen() to fix
this bug.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
