[ Upstream commit 1524773425 ]
Running generic/475(filesystem consistent tests after power cut) could
easily trigger unattached inode error while doing fsck:
Unattached zero-length inode 39405. Clear? no
Unattached inode 39405
Connect to /lost+found? no
Above inconsistence is caused by following process:
P1 P2
ext4_create
inode = ext4_new_inode_start_handle // itable records nlink=1
ext4_add_nondir
err = ext4_add_entry // ENOSPC
ext4_append
ext4_bread
ext4_getblk
ext4_map_blocks // returns ENOSPC
drop_nlink(inode) // won't be updated into disk inode
ext4_orphan_add(handle, inode)
ext4_orphan_file_add
ext4_journal_stop(handle)
jbd2_journal_commit_transaction // commit success
>> power cut <<
ext4_fill_super
ext4_load_and_init_journal // itable records nlink=1
ext4_orphan_cleanup
ext4_process_orphan
if (inode->i_nlink) // true, inode won't be deleted
Then, allocated inode will be reserved on disk and corresponds to no
dentries, so e2fsck reports 'unattached inode' problem.
The problem won't happen if orphan file feature is disabled, because
ext4_orphan_add() will update disk inode in orphan list mode. There
are several places not updating disk inode while putting inode into
orphan area, such as ext4_add_nondir(), ext4_symlink() and whiteout
in ext4_rename(). Fix it by updating inode into disk in all error
branches of these places.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217605
Fixes: 02f310fcf4 ("ext4: Speedup ext4 orphan inode handling")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230628132011.650383-1-chengzhihao1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c37b6908f7 ]
fail_iommu_setup() registers the fail_iommu_bus_notifier struct to both
PCI and VIO buses. struct notifier_block is a linked list node, so this
causes any notifiers later registered to either bus type to also be
registered to the other since they share the same node.
This causes issues in (at least) the vgaarb code, which registers a
notifier for PCI buses. pci_notify() ends up being called on a vio
device, converted with to_pci_dev() even though it's not a PCI device,
and finally makes a bad access in vga_arbiter_add_pci_device() as
discovered with KASAN:
BUG: KASAN: slab-out-of-bounds in vga_arbiter_add_pci_device+0x60/0xe00
Read of size 4 at addr c000000264c26fdc by task swapper/0/1
Call Trace:
dump_stack_lvl+0x1bc/0x2b8 (unreliable)
print_report+0x3f4/0xc60
kasan_report+0x244/0x698
__asan_load4+0xe8/0x250
vga_arbiter_add_pci_device+0x60/0xe00
pci_notify+0x88/0x444
notifier_call_chain+0x104/0x320
blocking_notifier_call_chain+0xa0/0x140
device_add+0xac8/0x1d30
device_register+0x58/0x80
vio_register_device_node+0x9ac/0xce0
vio_bus_scan_register_devices+0xc4/0x13c
__machine_initcall_pseries_vio_device_init+0x94/0xf0
do_one_initcall+0x12c/0xaa8
kernel_init_freeable+0xa48/0xba8
kernel_init+0x64/0x400
ret_from_kernel_thread+0x5c/0x64
Fix this by creating separate notifier_block structs for each bus type.
Fixes: d6b9a81b2a ("powerpc: IOMMU fault injection")
Reported-by: Nageswara R Sastry <rnsastry@linux.ibm.com>
Signed-off-by: Russell Currey <ruscur@russell.cc>
Tested-by: Nageswara R Sastry <rnsastry@linux.ibm.com>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
[mpe: Add #ifdef to fix CONFIG_IBMVIO=n build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230322035322.328709-1-ruscur@russell.cc
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9bbbf4979 ]
In mpc5xxx_fwnode_get_bus_frequency(), we should add
fwnode_handle_put() when break out of the iteration
fwnode_for_each_parent_node() as it will automatically
increase and decrease the refcounter.
Fixes: de06fba62a ("powerpc/mpc5xxx: Switch mpc5xxx_get_bus_frequency() to use fwnode")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230322030423.1855440-1-windhl@126.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 750bd41aea ]
With JUMP_LABEL=n, hcall_tracepoint_refcount's address is being tested
instead of its value. This results in the tracing slowpath always being
taken unnecessarily.
Fixes: 9a10ccb29c ("powerpc/pseries: move hcall_tracepoint_refcount out of .toc")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230509091600.70994-1-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08b45fcb2d ]
This allocation should use the passed in GFP_ flags instead of
GFP_KERNEL. One places where this matters is in filelayout_pg_init_write()
which uses GFP_NOFS as the allocation flags.
Fixes: 5c83746a0c ("pnfs/blocklayout: in-kernel GETDEVICEINFO XDR parsing")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eac030b22e ]
lppaca_shared_proc() takes a pointer to the lppaca which is typically
accessed through get_lppaca(). With DEBUG_PREEMPT enabled, this leads
to checking if preemption is enabled, for example:
BUG: using smp_processor_id() in preemptible [00000000] code: grep/10693
caller is lparcfg_data+0x408/0x19a0
CPU: 4 PID: 10693 Comm: grep Not tainted 6.5.0-rc3 #2
Call Trace:
dump_stack_lvl+0x154/0x200 (unreliable)
check_preemption_disabled+0x214/0x220
lparcfg_data+0x408/0x19a0
...
This isn't actually a problem however, as it does not matter which
lppaca is accessed, the shared proc state will be the same.
vcpudispatch_stats_procfs_init() already works around this by disabling
preemption, but the lparcfg code does not, erroring any time
/proc/powerpc/lparcfg is accessed with DEBUG_PREEMPT enabled.
Instead of disabling preemption on the caller side, rework
lppaca_shared_proc() to not take a pointer and instead directly access
the lppaca, bypassing any potential preemption checks.
Fixes: f13c13a005 ("powerpc: Stop using non-architected shared_proc field in lppaca")
Signed-off-by: Russell Currey <ruscur@russell.cc>
[mpe: Rework to avoid needing a definition in paca.h and lppaca.h]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230823055317.751786-4-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1aa0006676 ]
By adding a forward declaration for struct lppaca we can untangle paca.h
and lppaca.h. Also move get_lppaca() into lppaca.h for consistency.
Add includes of lppaca.h to some files that need it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230823055317.751786-3-mpe@ellerman.id.au
Stable-dep-of: eac030b22e ("powerpc/pseries: Rework lppaca_shared_proc() to avoid DEBUG_PREEMPT")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d18f6c5bb ]
I bump the decode_read_plus_maxsz to account for hole segments, but I
need to subtract out this increase when calling
rpc_prepare_reply_pages() so the common case of single data segment
replies can be directly placed into the xdr pages without needing to be
shifted around.
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Fixes: d3b00a802c ("NFS: Replace the READ_PLUS decoding code")
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8527028a7 ]
Assume that the first segment will be a DATA segment, and place the data
directly into the xdr pages so it doesn't need to be shifted.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Stable-dep-of: 8d18f6c5bb ("NFSv4.2: Fix READ_PLUS size calculations")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb05a617f0 ]
Smatch reports:
fs/nfs/nfs42xdr.c:1131 decode_read_plus() warn: missing error code? 'status'
Which Dan suggests to fix by doing a hardcoded "return 0" from the
"if (segments == 0)" check.
Additionally, smatch reports that the "status = -EIO" assignment is not
used. This patch addresses both these issues.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202305222209.6l5VM2lL-lkp@intel.com/
Fixes: d3b00a802c ("NFS: Replace the READ_PLUS decoding code")
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbd2a05f29 ]
Instead of using a tiny, static scratch buffer, we should use a kmalloc()-ed
buffer that is allocated when checking for read plus usage. This lets us
use the buffer before decoding any part of the READ_PLUS operation
instead of setting it right before segment decoding, meaning it should
be a little more robust.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Stable-dep-of: bb05a617f0 ("NFSv4.2: Fix READ_PLUS smatch warnings")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f139492a09 ]
Don't assume that only the driver would be accessing LNKCTL. ASPM policy
changes can trigger write to LNKCTL outside of driver's control.
Use RMW capability accessors which does proper locking to avoid losing
concurrent updates to the register value. On restore, clear the ASPMC field
properly.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Fixes: 76d870ed09 ("ath10k: enable ASPM")
Link: https://lore.kernel.org/r/20230717120503.15276-11-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c1b6bdb34 ]
Don't assume that only the driver would be accessing LNKCTL. ASPM policy
changes can trigger write to LNKCTL outside of driver's control.
Use RMW capability accessors which do proper locking to avoid losing
concurrent updates to the register value. On restore, clear the ASPMC field
properly.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Fixes: e9603f4bdc ("ath11k: pci: disable ASPM L0sLs before downloading firmware")
Link: https://lore.kernel.org/r/20230717120503.15276-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30de872537 ]
Don't assume that only the driver would be accessing LNKCTL of the upstream
bridge. ASPM policy changes can trigger write to LNKCTL outside of driver's
control.
Use RMW capability accessors which do proper locking to avoid losing
concurrent updates to the register value.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Fixes: eabe8e5e88 ("net/mlx5: Handle sync reset now event")
Link: https://lore.kernel.org/r/20230717120503.15276-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7189576e8a ]
Don't assume that only the driver would be accessing LNKCTL. ASPM policy
changes can trigger write to LNKCTL outside of driver's control. And in
the case of upstream bridge, the driver does not even own the device it's
changing the registers for.
Use RMW capability accessors which do proper locking to avoid losing
concurrent updates to the register value.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Fixes: 8a7cd27679 ("drm/radeon/cik: add support for pcie gen1/2/3 switching")
Fixes: b9d305dfb6 ("drm/radeon: implement pcie gen2/3 support for SI")
Link: https://lore.kernel.org/r/20230717120503.15276-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce7d88110b ]
Don't assume that only the driver would be accessing LNKCTL. ASPM policy
changes can trigger write to LNKCTL outside of driver's control. And in
the case of upstream bridge, the driver does not even own the device it's
changing the registers for.
Use RMW capability accessors which do proper locking to avoid losing
concurrent updates to the register value.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Fixes: a2e73f56fa ("drm/amdgpu: Add support for CIK parts")
Fixes: 62a3755341 ("drm/amdgpu: add si implementation v10")
Link: https://lore.kernel.org/r/20230717120503.15276-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34daf445f8 ]
CC arch/powerpc/perf/core-fsl-emb.o
arch/powerpc/perf/core-fsl-emb.c:675:6: error: no previous prototype for 'hw_perf_event_setup' [-Werror=missing-prototypes]
675 | void hw_perf_event_setup(int cpu)
| ^~~~~~~~~~~~~~~~~~~
Looks like fsl_emb was completely missed by commit 3f6da39053 ("perf:
Rework and fix the arch CPU-hotplug hooks")
So, apply same changes as commit 3f6da39053 ("perf: Rework and fix
the arch CPU-hotplug hooks") then commit 57ecde42cc ("powerpc/perf:
Convert book3s notifier to state machine callbacks")
While at it, also fix following error:
arch/powerpc/perf/core-fsl-emb.c: In function 'perf_event_interrupt':
arch/powerpc/perf/core-fsl-emb.c:648:13: error: variable 'found' set but not used [-Werror=unused-but-set-variable]
648 | int found = 0;
| ^~~~~
Fixes: 3f6da39053 ("perf: Rework and fix the arch CPU-hotplug hooks")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/603e1facb32608f88f40b7d7b9094adc50e7b2dc.1692349125.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1eb75e0df ]
In case fadump_reserve_mem() fails to reserve memory, the
reserve_dump_area_size variable will retain the reserve area size. This
will lead to /sys/kernel/fadump/mem_reserved node displaying an incorrect
memory reserved by fadump.
To fix this problem, reserve dump area size variable is set to 0 if fadump
failed to reserve memory.
Fixes: 8255da95e5 ("powerpc/fadump: release all the memory above boot memory size")
Signed-off-by: Sourabh Jain <sourabhjain@linux.ibm.com>
Acked-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230704050715.203581-1-sourabhjain@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08ca6906a4 ]
'nd_pmu->pmu.attr_groups' is dereferenced in function
'nvdimm_pmu_free_hotplug_memory' call after it has been freed. Because in
function 'nvdimm_pmu_free_hotplug_memory' memory pointed by the fields of
'nd_pmu->pmu.attr_groups' is deallocated it is necessary to call 'kfree'
after 'nvdimm_pmu_free_hotplug_memory'.
Fixes: 0fab1ba6ad ("drivers/nvdimm: Add perf interface to expose nvdimm performance stats")
Co-developed-by: Ivanov Mikhail <ivanov.mikhail1@huawei-partners.com>
Signed-off-by: Konstantin Meskhidze <konstantin.meskhidze@huawei.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Link: https://lore.kernel.org/r/20230817114103.754977-1-konstantin.meskhidze@huawei.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85ae42c721 ]
Memory pointed by 'nd_pmu->pmu.attr_groups' is allocated in function
'register_nvdimm_pmu' and is lost after 'kfree(nd_pmu)' call in function
'unregister_nvdimm_pmu'.
Fixes: 0fab1ba6ad ("drivers/nvdimm: Add perf interface to expose nvdimm performance stats")
Co-developed-by: Ivanov Mikhail <ivanov.mikhail1@huawei-partners.com>
Signed-off-by: Konstantin Meskhidze <konstantin.meskhidze@huawei.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Link: https://lore.kernel.org/r/20230817115945.771826-1-konstantin.meskhidze@huawei.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd24e2a60a ]
Fix an information leak where an uninitialized hole in struct
vfio_iommu_type1_info_cap_migration on the stack is exposed to userspace.
The definition of struct vfio_iommu_type1_info_cap_migration contains a hole as
shown in this pahole(1) output:
struct vfio_iommu_type1_info_cap_migration {
struct vfio_info_cap_header header; /* 0 8 */
__u32 flags; /* 8 4 */
/* XXX 4 bytes hole, try to pack */
__u64 pgsize_bitmap; /* 16 8 */
__u64 max_dirty_bitmap_size; /* 24 8 */
/* size: 32, cachelines: 1, members: 4 */
/* sum members: 28, holes: 1, sum holes: 4 */
/* last cacheline: 32 bytes */
};
The cap_mig variable is filled in without initializing the hole:
static int vfio_iommu_migration_build_caps(struct vfio_iommu *iommu,
struct vfio_info_cap *caps)
{
struct vfio_iommu_type1_info_cap_migration cap_mig;
cap_mig.header.id = VFIO_IOMMU_TYPE1_INFO_CAP_MIGRATION;
cap_mig.header.version = 1;
cap_mig.flags = 0;
/* support minimum pgsize */
cap_mig.pgsize_bitmap = (size_t)1 << __ffs(iommu->pgsize_bitmap);
cap_mig.max_dirty_bitmap_size = DIRTY_BITMAP_SIZE_MAX;
return vfio_info_add_capability(caps, &cap_mig.header, sizeof(cap_mig));
}
The structure is then copied to a temporary location on the heap. At this point
it's already too late and ioctl(VFIO_IOMMU_GET_INFO) copies it to userspace
later:
int vfio_info_add_capability(struct vfio_info_cap *caps,
struct vfio_info_cap_header *cap, size_t size)
{
struct vfio_info_cap_header *header;
header = vfio_info_cap_add(caps, size, cap->id, cap->version);
if (IS_ERR(header))
return PTR_ERR(header);
memcpy(header + 1, cap + 1, size - sizeof(*header));
return 0;
}
This issue was found by code inspection.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Fixes: ad721705d0 ("vfio iommu: Add migration capability to report supported features")
Link: https://lore.kernel.org/r/20230801155352.1391945-1-stefanha@redhat.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a9dd8f292 ]
With skiboot_defconfig, Clang reports:
CC arch/powerpc/mm/book3s64/radix_tlb.o
arch/powerpc/mm/book3s64/radix_tlb.c:419:20: error: unused function '_tlbie_pid_lpid' [-Werror,-Wunused-function]
static inline void _tlbie_pid_lpid(unsigned long pid, unsigned long lpid,
^
arch/powerpc/mm/book3s64/radix_tlb.c:663:20: error: unused function '_tlbie_va_range_lpid' [-Werror,-Wunused-function]
static inline void _tlbie_va_range_lpid(unsigned long start, unsigned long end,
^
This is because those functions are only called from functions
enclosed in a #ifdef CONFIG_KVM_BOOK3S_HV_POSSIBLE
Move below functions inside that #ifdef
* __tlbie_pid_lpid(unsigned long pid,
* __tlbie_va_lpid(unsigned long va, unsigned long pid,
* fixup_tlbie_pid_lpid(unsigned long pid, unsigned long lpid)
* _tlbie_pid_lpid(unsigned long pid, unsigned long lpid,
* fixup_tlbie_va_range_lpid(unsigned long va,
* __tlbie_va_range_lpid(unsigned long start, unsigned long end,
* _tlbie_va_range_lpid(unsigned long start, unsigned long end,
Fixes: f0c6fbbb90 ("KVM: PPC: Book3S HV: Add support for H_RPT_INVALIDATE")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202307260802.Mjr99P5O-lkp@intel.com/
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/3d72efd39f986ee939d068af69fdce28bd600766.1691568093.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4dd432d985 ]
Reconfiguring the clock divider to the exact same value is observed
on an i.MX8MN to often cause a longer than usual clock pause, probably
because the divider restarts counting whenever the register is rewritten.
This issue doesn't show up normally, because the clock framework will
take care to not call set_rate when the clock rate is the same.
However, when we reconfigure an upstream clock, the common code will
call set_rate with the newly calculated rate on all children, e.g.:
- sai5 is running normally and divides Audio PLL out by 16.
- Audio PLL rate is increased by 32Hz (glitch-free kdiv change)
- rates for children are recalculated and rates are set recursively
- imx8m_clk_composite_divider_set_rate(sai5) is called with
32/16 = 2Hz more
- imx8m_clk_composite_divider_set_rate computes same divider as before
- divider register is written, so it restarts counting from zero and
MCLK is briefly paused, so instead of e.g. 40ns, MCLK is low for 120ns.
Some external clock consumers can be upset by such unexpected clock pauses,
so let's make sure we only rewrite the divider value when the value to be
written is actually different.
Fixes: d3ff972813 ("clk: imx: Add imx composite clock")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20230807082201.2332746-1-a.fatoum@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c30f600f1f ]
The reference manual don't mention a SAI4 hardware block. This would be
clock slice 78 which is skipped (TRM, page 237). Remove any reference to
this clock to align the driver with the reality.
Fixes: 9c140d9926 ("clk: imx: Add support for i.MX8MP clock driver")
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230731142150.3186650-1-m.felsch@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7653a59be8 ]
The SPLL2 on iMX8ULP is different with other frac PLLs, it can
support VCO from 650Mhz to 1Ghz. Following the changes to pllv4,
use the new type IMX_PLLV4_IMX8ULP_1GHZ.
Fixes: c43a801a57 ("clk: imx: Add clock driver for imx8ulp")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230625123340.4067536-2-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f0cdb9454 ]
The SPLL2 on iMX8ULP is different with other frac PLLs, it can
support VCO from 650Mhz to 1Ghz. According to RM, the MULT is
using a range from 27 to 54, not some fixed values. If using
current PLL implementation, some clock rate can't be supported.
Fix the issue by adding new type for the SPLL2 and use MULT range
to replace MULT table
Fixes: 5f0601c47c ("clk: imx: Update the pllv4 to support imx8ulp")
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230625123340.4067536-1-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e09060b3b6 ]
Don't assume that the device is fully under the control of ASPM and use RMW
capability accessors which do proper locking to avoid losing concurrent
updates to the register values.
If configuration fails in pcie_aspm_configure_common_clock(), the
function attempts to restore the old PCI_EXP_LNKCTL_CCC settings. Store
only the old PCI_EXP_LNKCTL_CCC bit for the relevant devices rather
than the content of the whole LNKCTL registers. It aligns better with
how pcie_lnkctl_clear_and_set() expects its parameter and makes the
code more obvious to understand.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Fixes: 2a42d9dba7 ("PCIe: ASPM: Break out of endless loop waiting for PCI config bits to switch")
Fixes: 7d715a6c1a ("PCI: add PCI Express ASPM support")
Link: https://lore.kernel.org/r/20230717120503.15276-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f75f96c61 ]
As hotplug is not the only driver touching LNKCTL, use the RMW capability
accessor which handles concurrent changes correctly.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Fixes: 7f822999e1 ("PCI: pciehp: Add Disable/enable link functions")
Link: https://lore.kernel.org/r/20230717120503.15276-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e70d0acf0 ]
Many places in the kernel write the Link Control and Root Control PCI
Express Capability Registers without proper concurrency control and this
could result in losing the changes one of the writers intended to make.
Add pcie_cap_lock spinlock into the struct pci_dev and use it to protect
bit changes made in the RMW capability accessors. Protect only a selected
set of registers by differentiating the RMW accessor internally to
locked/unlocked variants using a wrapper which has the same signature as
pcie_capability_clear_and_set_word(). As the Capability Register (pos)
given to the wrapper is always a constant, the compiler should be able to
simplify all the dead-code away.
So far only the Link Control Register (ASPM, hotplug, link retraining,
various drivers) and the Root Control Register (AER & PME) seem to
require RMW locking.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Fixes: c7f486567c ("PCI PM: PCIe PME root port service driver")
Fixes: f12eb72a26 ("PCI/ASPM: Use PCI Express Capability accessors")
Fixes: 7d715a6c1a ("PCI: add PCI Express ASPM support")
Fixes: affa48de84 ("staging/rdma/hfi1: Add support for enabling/disabling PCIe ASPM")
Fixes: 849a9366cb ("misc: rtsx: Add support new chip rts5228 mmc: rtsx: Add support MMC_CAP2_NO_MMC")
Fixes: 3d1e7aa80d ("misc: rtsx: Use pcie_capability_clear_and_set_word() for PCI_EXP_LNKCTL")
Fixes: c0e5f4e73a ("misc: rtsx: Add support for RTS5261")
Fixes: 3df4fce739 ("misc: rtsx: separate aspm mode into MODE_REG and MODE_CFG")
Fixes: 121e9c6b5c ("misc: rtsx: modify and fix init_hw function")
Fixes: 19f3bd548f ("mfd: rtsx: Remove LCTLR defination")
Fixes: 773ccdfd9c ("mfd: rtsx: Read vendor setting from config space")
Fixes: 8275b77a15 ("mfd: rts5249: Add support for RTS5250S power saving")
Fixes: 5da4e04ae4 ("misc: rtsx: Add support for RTS5260")
Fixes: 0f49bfbd0f ("tg3: Use PCI Express Capability accessors")
Fixes: 5e7dfd0fb9 ("tg3: Prevent corruption at 10 / 100Mbps w CLKREQ")
Fixes: b726e493e8 ("r8169: sync existing 8168 device hardware start sequences with vendor driver")
Fixes: e6de30d63e ("r8169: more 8168dp support.")
Fixes: 8a06127602 ("Bluetooth: hci_bcm4377: Add new driver for BCM4377 PCIe boards")
Fixes: 6f461f6c7c ("e1000e: enable/disable ASPM L0s and L1 and ERT according to hardware errata")
Fixes: 1eae4eb2a1 ("e1000e: Disable L1 ASPM power savings for 82573 mobile variants")
Fixes: 8060e169e0 ("ath9k: Enable extended synch for AR9485 to fix L0s recovery issue")
Fixes: 69ce674bfa ("ath9k: do btcoex ASPM disabling at initialization time")
Fixes: f37f055035 ("mt76: mt76x2e: disable pcie_aspm by default")
Link: https://lore.kernel.org/r/20230717120503.15276-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 278294798a ]
PCI config space access from user space has traditionally been
unrestricted with writes being an understood risk for device operation.
Unfortunately, device breakage or odd behavior from config writes lacks
indicators that can leave driver writers confused when evaluating
failures. This is especially true with the new PCIe Data Object
Exchange (DOE) mailbox protocol where backdoor shenanigans from user
space through things such as vendor defined protocols may affect device
operation without complete breakage.
A prior proposal restricted read and writes completely.[1] Greg and
Bjorn pointed out that proposal is flawed for a couple of reasons.
First, lspci should always be allowed and should not interfere with any
device operation. Second, setpci is a valuable tool that is sometimes
necessary and it should not be completely restricted.[2] Finally
methods exist for full lock of device access if required.
Even though access should not be restricted it would be nice for driver
writers to be able to flag critical parts of the config space such that
interference from user space can be detected.
Introduce pci_request_config_region_exclusive() to mark exclusive config
regions. Such regions trigger a warning and kernel taint if accessed
via user space.
Create pci_warn_once() to restrict the user from spamming the log.
[1] https://lore.kernel.org/all/161663543465.1867664.5674061943008380442.stgit@dwillia2-desk3.amr.corp.intel.com/
[2] https://lore.kernel.org/all/YF8NGeGv9vYcMfTV@kroah.com/
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20220926215711.2893286-2-ira.weiny@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Stable-dep-of: 5e70d0acf0 ("PCI: Add locking to RMW PCI Express Capability Register accessors")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5af729dc2 ]
NVIDIA T4 GPUs do not work with SBR. This problem is found when the T4 card
is direct attached to a Root Port only. Avoid bus reset by marking T4 GPUs
PCI_DEV_FLAGS_NO_BUS_RESET.
Fixes: 4c207e7121 ("PCI: Mark some NVIDIA GPUs to avoid bus reset")
Link: https://lore.kernel.org/r/2dcebea53a6eb9bd212ec6d8974af2e5e0333ef6.1681129861.git.wuzongyong@linux.alibaba.com
Signed-off-by: Wu Zongyong <wuzongyong@linux.alibaba.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d473a5a26 ]
The SEC and DED interrupt bits are laid out the wrong way round so the SEC
interrupt handler attempts to mask, unmask, and clear the DED interrupt
and vice versa. Correct the bit offsets so that each interrupt handler
operates properly.
Link: https://lore.kernel.org/r/20230728131401.1615724-2-daire.mcnamara@microchip.com
Fixes: 6f15a9c9f9 ("PCI: microchip: Add Microchip PolarFire PCIe controller driver")
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df04d166d1 ]
GPLL7 is not on by default, which causes a "gcc_sdcc2_apps_clk_src: rcg
didn't update its configuration" error when booting. Set .flags =
CLK_OPS_PARENT_ENABLE to fix the error.
Fixes: 131abae905 ("clk: qcom: Add SM6350 GCC driver")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230804-sm6350-sdcc2-v1-1-3d946927d37d@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e0f4f2918 ]
kvm_vfio_group_add() creates kvg instance, links it to kv->group_list,
and calls kvm_vfio_file_set_kvm() with kvg->file as an argument after
dropping kv->lock. If we race group addition and deletion calls, kvg
instance may get freed by the time we get around to calling
kvm_vfio_file_set_kvm().
Previous iterations of the code did not reference kvg->file outside of
the critical section, but used a temporary variable. Still, they had
similar problem of the file reference being owned by kvg structure and
potential for kvm_vfio_group_del() dropping it before
kvm_vfio_group_add() had a chance to complete.
Fix this by moving call to kvm_vfio_file_set_kvm() under the protection
of kv->lock. We already call it while holding the same lock when vfio
group is being deleted, so it should be safe here as well.
Fixes: 2fc1bec158 ("kvm: set/clear kvm to/from vfio_group when group add/delete")
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20230714224538.404793-1-dmitry.torokhov@gmail.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 783cb69382 ]
GPLL9 is not on by default, which causes a "gcc_sdcc2_apps_clk_src: rcg
didn't update its configuration" error when booting. Set .flags =
CLK_OPS_PARENT_ENABLE to fix the error.
Fixes: 3e5770921a ("clk: qcom: gcc: Add global clock controller driver for SM8250")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Patrick Whewell <patrick.whewell@sightlineapplications.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20230802210359.408-1-patrick.whewell@sightlineapplications.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60c672b7f2 ]
ngroups is ext4_group_t (unsigned int) while next_linear_group treat it
in int. If ngroups is bigger than max number described by int, it will
be treat as a negative number. Then "return group + 1 >= ngroups ? 0 :
group + 1;" may keep returning 0.
Switch int to ext4_group_t in next_linear_group to fix the overflow.
Fixes: 196e402adf ("ext4: improve cr 0 / cr 1 group scanning")
Signed-off-by: Kemeng Shi <shikemeng@huaweicloud.com>
Reviewed-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Link: https://lore.kernel.org/r/20230801143204.2284343-3-shikemeng@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9ce5993a0 ]
Group corruption check will access memory of grp and will trigger kernel
crash if grp is NULL. So do NULL check before corruption check.
Fixes: 5354b2af34 ("ext4: allow ext4_get_group_info() to fail")
Signed-off-by: Kemeng Shi <shikemeng@huaweicloud.com>
Reviewed-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Link: https://lore.kernel.org/r/20230801143204.2284343-2-shikemeng@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce53ad81ed ]
Current igen6_edac checks for pending errors before the registration
of the error handler. However, there is a possibility that the error
occurs during the registration process, leading to unhandled pending
errors and no future error events. This issue can be reproduced by
repeatedly injecting errors during the loading of the igen6_edac.
Fix this issue by moving the pending error handler after the registration
of the error handler, ensuring that no pending errors are left unhandled.
Fixes: 10590a9d4f ("EDAC/igen6: Add EDAC driver for Intel client SoCs using IBECC")
Reported-by: Ee Wey Lim <ee.wey.lim@intel.com>
Tested-by: Ee Wey Lim <ee.wey.lim@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20230725080427.23883-1-qiuxu.zhuo@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3a3a097ea ]
The following debug object splat was observed in testing:
ODEBUG: free active (active state 0) object: 0000000097d23782 object type: work_struct hint: doe_statemachine_work+0x0/0x510
WARNING: CPU: 1 PID: 71 at lib/debugobjects.c:514 debug_print_object+0x7d/0xb0
...
Workqueue: pci 0000:36:00.0 DOE [1 doe_statemachine_work
RIP: 0010:debug_print_object+0x7d/0xb0
...
Call Trace:
? debug_print_object+0x7d/0xb0
? __pfx_doe_statemachine_work+0x10/0x10
debug_object_free.part.0+0x11b/0x150
doe_statemachine_work+0x45e/0x510
process_one_work+0x1d4/0x3c0
This occurs because destroy_work_on_stack() was called after signaling
the completion in the calling thread. This creates a race between
destroy_work_on_stack() and the task->work struct going out of scope in
pci_doe().
Signal the work complete after destroying the work struct. This is safe
because signal_task_complete() is the final thing the work item does and
the workqueue code is careful not to access the work struct after.
Fixes: abf04be0e7 ("PCI/DOE: Fix memory leak with CONFIG_DEBUG_OBJECTS=y")
Link: https://lore.kernel.org/r/20230726-doe-fix-v1-1-af07e614d4dd@intel.com
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9cbc06049 ]
Currently, as part of the qcom_pcie_perst_deassert() function, instead
of writing the updated value to clear PARF_MSTR_AXI_CLK_EN, the variable
"val" is re-read.
This must be fixed to ensure that the master clock supplied to the MHI
bus is correctly gated during L1.1/L1.2 to save power.
Thus, replace the line that re-reads "val" with a line that writes the
updated value to the register to clear PARF_MSTR_AXI_CLK_EN.
[kwilczynski: commit log]
Fixes: c457ac029e ("PCI: qcom-ep: Gate Master AXI clock to MHI bus during L1SS")
Link: https://lore.kernel.org/linux-pci/20230627141036.11600-1-manivannan.sadhasivam@linaro.org
Reported-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8650c0c2a ]
The apple_pcie_setup_port() function computes ilog2(pcie->nvecs) to set
up the number of MSIs available for each port. However, it's called
before apple_msi_init(), which initializes pcie->nvecs.
Luckily, pcie->nvecs is part of kzalloc()-ed structure and, as such,
initialized as zero. ilog2(0) happens to be 0xffffffff which then simply
configures more MSIs in hardware than we have. This doesn't break
anything because we never hand out those vectors.
Thus, swap the order of the two calls so that the correctly initialized
value is then used.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20230311133453.63246-1-sven@svenpeter.dev
Fixes: 476c41ed45 ("PCI: apple: Implement MSI support")
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dafebd0f9a ]
PLL rate on RK356x is calculated through the simple formula:
((24000000 / _refdiv) * _fbdiv) / (_postdiv1 * _postdiv2)
The PLL rate setting for 78.75MHz seems to be copied from 96MHz
so this patch fixes it and configures it properly.
Signed-off-by: Alibek Omarov <a1ba.omarov@gmail.com>
Fixes: 842f4cb726 ("clk: rockchip: Add more PLL rates for rk3568")
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20230614134750.1056293-1-a1ba.omarov@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4712eb7ff8 ]
There are 10 more GDSCs that we've not been caring about, and by extension
(and perhaps even more importantly), not putting to sleep. Add them.
Fixes: d65d005f9a ("clk: qcom: add sc8280xp GCC driver")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230620-topic-sc8280_gccgdsc-v2-3-562c1428c10d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
