Patch f598282f51 exposed a problem in
powerpc MSI-X functionality, making network interfaces such as ixgbe
and cxgb3 stop to work when MSI-X is enabled. RX interrupts were not
being generated.
The problem was caused because MSI irq was not being effectively
unmasked after device initialization.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Profiling of a page fault scalability microbenchmark shows flush_hash_range
is not calling the batch hpte invalidate hcall (H_BULK_REMOVE).
It turns out we have a duplicate firmware feature for hcall-bulk and the
current setup code stops after finding the first match. This meant we never
batch and always do individual invalidates.
The patch below removes the duplicate and shifts FW_FEATURE_CMO to close
the gap. With the patch applied the single threaded page fault rate improves
from 217169 to 238755 per second on a POWER5 test box, a 10% improvement.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Sometimes this is used to hold a simple offset, and sometimes
it is used to hold a pointer. This patch changes it to a union containing
void * and dma_addr_t. get/set accessors are also provided, because it was
getting a bit ugly to get to the actual data.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the accessors rather than frobbing bits directly (the new versions
are const).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Make all seq_operations structs const, to help mitigate against
revectoring user-triggerable function pointers.
This is derived from the grsecurity patch, although generated from scratch
because it's simpler than extracting the changes from there.
Signed-off-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (75 commits)
PCI hotplug: clean up acpi_run_hpp()
PCI hotplug: acpiphp: use generic pci_configure_slot()
PCI hotplug: shpchp: use generic pci_configure_slot()
PCI hotplug: pciehp: use generic pci_configure_slot()
PCI hotplug: add pci_configure_slot()
PCI hotplug: clean up acpi_get_hp_params_from_firmware() interface
PCI hotplug: acpiphp: don't cache hotplug_params in acpiphp_bridge
PCI hotplug: acpiphp: remove superfluous _HPP/_HPX evaluation
PCI: Clear saved_state after the state has been restored
PCI PM: Return error codes from pci_pm_resume()
PCI: use dev_printk in quirk messages
PCI / PCIe portdrv: Fix pcie_portdrv_slot_reset()
PCI Hotplug: convert acpi_pci_detect_ejectable() to take an acpi_handle
PCI Hotplug: acpiphp: find bridges the easy way
PCI: pcie portdrv: remove unused variable
PCI / ACPI PM: Propagate wake-up enable for devices w/o ACPI support
ACPI PM: Replace wakeup.prepared with reference counter
PCI PM: Introduce device flag wakeup_prepared
PCI / ACPI PM: Rework some debug messages
PCI PM: Simplify PCI wake-up code
...
Fixed up conflict in arch/powerpc/kernel/pci_64.c due to OF device tree
scanning having been moved and merged for the 32- and 64-bit cases. The
'needs_freset' initialization added in 6e19314cc ("PCI/powerpc: support
PCIe fundamental reset") is now in arch/powerpc/kernel/pci_of_scan.c.
Currently there is a bug where if you use oprofile on a pSeries
machine, then use perf_counters, then use oprofile again, oprofile
will not work correctly; it will lose the PMU configuration the next
time the hypervisor does a partition context switch, and thereafter
won't count anything.
Maynard Johnson identified the sequence causing the problem:
- oprofile setup calls ppc_enable_pmcs(), which calls
pseries_lpar_enable_pmcs, which tells the hypervisor that we want
to use the PMU, and sets the "PMU in use" flag in the lppaca.
This flag tells the hypervisor whether it needs to save and restore
the PMU config.
- The perf_counter code sets and clears the "PMU in use" flag directly
as it context-switches the PMU between tasks, and leaves it clear
when it finishes.
- oprofile setup, called for a new oprofile run, calls ppc_enable_pmcs,
which does nothing because it has already been called. In particular
it doesn't set the "PMU in use" flag.
This fixes the problem by arranging for ppc_enable_pmcs to always set
the "PMU in use" flag. It makes the perf_counter code call
ppc_enable_pmcs also rather than calling the lower-level function
directly, and removes the setting of the "PMU in use" flag from
pseries_lpar_enable_pmcs, since that is now done in its caller.
This also removes the declaration of pasemi_enable_pmcs because it
isn't defined anywhere.
Reported-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: <stable@kernel.org)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
By default, the EEH framework on powerpc does what's known as a "hot
reset" during recovery of a PCI Express device. We've found a case
where the device needs a "fundamental reset" to recover properly. The
current PCI error recovery and EEH frameworks do not support this
distinction.
The attached patch makes changes to EEH to utilize the new bit field.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Signed-off-by: Richard Lary <rlary@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The SLB can change sizes across a live migration, which was not
being handled, resulting in possible machine crashes during
migration if migrating to a machine which has a smaller max SLB
size than the source machine. Fix this by first reducing the
SLB size to the minimum possible value, which is 32, prior to
migration. Then during the device tree update which occurs after
migration, we make the call to ensure the SLB gets updated. Also
add the slb_size to the lparcfg output so that the migration
tools can check to make sure the kernel has this capability
before allowing migration in scenarios where the SLB size will change.
BenH: Fixed #include <asm/mmu-hash64.h> -> <asm/mmu.h> to avoid
breaking ppc32 build
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The two versions are doing almost exactly the same thing. No need to
maintain them as separate files. This patch also has the side effect
of making the PCI device tree scanning code available to 32 bit powerpc
machines, but no board ports actually make use of this feature at this
point.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Those definitions are currently declared extern in the .c file where
they are used, move them to a header file instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when DEBUG
is not defined. That's not really desirable in some places.
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
7720 5488 296 13504 34c0 platforms/pseries/xics.o
size after:
text data bss dec hex filename
7535 5456 296 13287 33e7 platforms/pseries/xics.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when DEBUG
is not defined. That's not really desirable in some places.
In particular, pSeries_lpar_hpte_insert() goes from 185 instructions
to 77 instructions as a result of this patch. Luckily that code
isn't called very often ...
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
7284 1552 296 9132 23ac platforms/pseries/lpar.o
size after:
text data bss dec hex filename
5806 1096 296 7198 1c1e platforms/pseries/lpar.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Several platforms use their own copy of what is essentially the same code,
using RTAS to synchronize the timebases when bringing up new CPUs. This
moves it all into a single common implementation and additionally
turns the spinlock into a raw spinlock since the former can rely on
the timebase not being frozen when spinlock debugging is enabled, and finally
masks interrupts while the timebase is disabled.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (74 commits)
PCI: make msi_free_irqs() to use msix_mask_irq() instead of open coded write
PCI: Fix the NIU MSI-X problem in a better way
PCI ASPM: remove get_root_port_link
PCI ASPM: cleanup pcie_aspm_sanity_check
PCI ASPM: remove has_switch field
PCI ASPM: cleanup calc_Lx_latency
PCI ASPM: cleanup pcie_aspm_get_cap_device
PCI ASPM: cleanup clkpm checks
PCI ASPM: cleanup __pcie_aspm_check_state_one
PCI ASPM: cleanup initialization
PCI ASPM: cleanup change input argument of aspm functions
PCI ASPM: cleanup misc in struct pcie_link_state
PCI ASPM: cleanup clkpm state in struct pcie_link_state
PCI ASPM: cleanup latency field in struct pcie_link_state
PCI ASPM: cleanup aspm state field in struct pcie_link_state
PCI ASPM: fix typo in struct pcie_link_state
PCI: drivers/pci/slot.c should depend on CONFIG_SYSFS
PCI: remove redundant __msi_set_enable()
PCI PM: consistently use type bool for wake enable variable
x86/ACPI: Correct maximum allowed _CRS returned resources and warn if exceeded
...
Based on PCI Express AER specs, a root port might receive multiple
TLP errors while it could only save a correctable error source id
and an uncorrectable error source id at the same time. In addition,
some root port hardware might be unable to provide a correct source
id, i.e., the source id, or the bus id part of the source id provided
by root port might be equal to 0.
The patchset implements the support in kernel by searching the device
tree under the root port.
Patch 1 changes parameter cb of function pci_walk_bus to return a value.
When cb return non-zero, pci_walk_bus stops more searching on the
device tree.
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Zhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
resource_size_t is 64 bits on pseries
Gets rid of these warnings:
arch/powerpc/platforms/pseries/iommu.c: In function 'pci_dma_bus_setup_pSeries':
arch/powerpc/platforms/pseries/iommu.c:391: warning: format '%lx' expects type 'long unsigned int', but argument 2 has type 'resource_size_t'
arch/powerpc/platforms/pseries/iommu.c:417: warning: format '%lx' expects type 'long unsigned int', but argument 2 has type 'resource_size_t'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
RTAS event scan has to run across all cpus. Right now we use a kernel
thread and set_cpus_allowed but in doing so we wake up the previous cpu
unnecessarily.
Some ftrace output shows this:
previous cpu (2):
[002] 7.022331: sched_switch: task swapper:0 [140] ==> rtasd:194 [120]
[002] 7.022338: sched_switch: task rtasd:194 [120] ==> migration/2:9 [0]
[002] 7.022344: sched_switch: task migration/2:9 [0] ==> swapper:0 [140]
next cpu (3):
[003] 7.022345: sched_switch: task swapper:0 [140] ==> rtasd:194 [120]
[003] 7.022371: sched_switch: task rtasd:194 [120] ==> swapper:0 [140]
We can use schedule_delayed_work_on and avoid the unnecessary wakeup.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There doesn't appear to be any specific reason that we need to setup the
pseries specific notifier in generic arch pci code. Move it into pseries
land.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adds support for the "unused" page hint which can be used in shared
memory partitions to flag pages not in use, which will then be stolen
before active pages by the hypervisor when memory needs to be moved to
LPARs in need of additional memory. Failure to mark pages as 'unused'
makes the LPAR slower to give up unused memory to other partitions.
This adds the kernel parameter 'cmo_free_hint' to disable this
functionality.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
according to Ingo, change set_affinity() in irq_chip should return int,
because that way we can handle failure cases in a much cleaner way, in
the genirq layer.
v2: fix two typos
[ Impact: extend API ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-arch@vger.kernel.org
LKML-Reference: <49F654E9.4070809@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A randconfig build on powerpc failed with:
dtl.c: In function 'dtl_init':
dtl.c:238: error: implicit declaration of function 'firmware_has_feature'
dtl.c:238: error: 'FW_FEATURE_SPLPAR' undeclared (first use in this function)
- We need firmware.h for these definitions.
Signed-off-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
While adding native EEH support to Emulex and Qlogic drivers, it was
discovered that dev->error_state was set to pci_io_channel_normal too
late in the recovery process. These drivers rely on error_state to
determine if they can access the device in their slot_reset callback,
thus error_state needs to be set to pci_io_channel_normal in
eeh_report_reset(). Below is a detailed explanation (courtesy of Richard
Lary) as to why this is necessary.
Background:
PCI MMIO or DMA accesses to a frozen slot generate additional EEH
errors. If the number of additional EEH errors exceeds EEH_MAX_FAILS the
adapter will be shutdown. To avoid triggering excessive EEH errors and
an undesirable adapter shutdown, some drivers use the
pci_channel_offline(dev) wrapper function to return a Boolean value
based on the value of pci_dev->error_state to determine if PCI MMIO or
DMA accesses are safe. If the wrapper returns TRUE, drivers must not
make PCI MMIO or DMA access to their hardware.
The pci_dev structure member error_state reflects one of three values,
1) pci_channel_io_normal, 2) pci_channel_io_frozen, 3)
pci_channel_io_perm_failure. Function pci_channel_offline(dev) returns
TRUE if error_state is pci_channel_io_frozen or pci_channel_io_perm_failure.
The EEH driver sets pci_dev->error_state to pci_channel_io_frozen at the
point where the PCI slot is frozen. Currently, the EEH driver restores
dev->error_state to pci_channel_io_normal in eeh_report_resume() before
calling the driver's resume callback. However, when the EEH driver calls
the driver's slot_reset callback() from eeh_report_reset(), it
incorrectly indicates the error state is still pci_channel_io_frozen.
Waiting until eeh_report_resume() to restore dev->error_state to
pci_channel_io_normal is too late for Emulex and QLogic FC drivers and
any other drivers which are designed to use common code paths in these
two cases: i) those called after the driver's slot_reset callback() and
ii) those called after the PCI slot is frozen but before the driver's
slot_reset callback is called. Case i) all driver paths executed to
reinitialize the hardware after a reset and case ii) all code paths
executed by driver kernel threads that run asynchronous to the main
driver thread, such as interrupt handlers and worker threads to process
driver work queues.
Emulex and QLogic FC drivers are designed with common code paths which
require that pci_channel_offline(dev) reflect the true state of the
hardware. The state transitions that the hardware takes from Normal
Operations to Slot Frozen to Reset to Normal Operations are documented
in the Power Architecture™ Platform Requirements+ (PAPR+) in Table 75.
PE State Control.
PAPR defines the following 3 states:
0 -- Not reset, Not EEH stopped, MMIO load/store allowed, DMA allowed
(Normal Operations)
1 -- Reset, Not EEH stopped, MMIO load/store disabled, DMA disabled
2 -- Not reset, EEH stopped, MMIO load/store disabled, DMA disabled
(Slot Frozen)
An EEH error places the slot in state 2 (Frozen) and the adapter driver
is notified that an EEH error was detected. If the adapter driver
returns PCI_ERS_RESULT_NEED_RESET, the EEH driver calls
eeh_reset_device() to place the slot into state 1 (Reset) and
eeh_reset_device completes by placing the slot into State 0 (Normal
Operations). Upon return from eeh_reset_device(), the EEH driver calls
eeh_report_reset, which then calls the adapter's slot_reset callback. At
the time the adapter's slot_reset callback is called, the true state of
the hardware is Normal Operations and should be accurately reflected by
setting dev->error_state to pci_channel_io_normal.
The current implementation of EEH driver does not do so and requires
this change to correct this deficiency.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, we don't enforce any ordering for updates to the lppaca
when enabling dtl logging, so we may end up enabling logging before the
index fields have been established.
This change adds a smp_wmb() before doing the actual enable.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pseries SPLPAR machines are able to retrieve a log of dispatch and
preempt events from the hypervisor. With this information, we can
see when and why each dispatch & preempt is occuring.
This change adds a set of debugfs files allowing userspace to read this
dispatch log.
Based on initial patches from Nishanth Aravamudan <nacc@us.ibm.com>.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The return code from invoking the notifier chain when updating the
ibm,dynamic-memory property is not handled properly. In failure
cases (rc == NOTIFY_BAD) we should be restoring the original value
of the property. In success (rc == NOTIFY_OK) we should be returning
zero from the calling routine.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CONFIG_PPC_MULTIPLATFORM is a remain of the pre-powerpc days and isn't
really meaningful anymore. It was basically equivalent to PPC64 || 6xx.
This removes it along with the following changes:
- 32-bit platforms that relied on PPC32 && PPC_MULTIPLATFORM now rely
on 6xx which is what they want anyway.
- A new symbol, PPC_BOOK3S, is defined that represent compliance with
the "Server" variant of the architecture. This is set when either 6xx
or PPC64 is set and open the door for future BOOK3E 64-bit.
- 64-bit platforms that relied on PPC64 && PPC_MULTIPLATFORM now use
PPC64 && PPC_BOOK3S
- A separate and selectable CONFIG_PPC_OF_BOOT_TRAMPOLINE option is now
used to control the use of prom_init.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There's no way for us to express to firmware that we want a
discontiguous, or non-zero based, range of MSI-X entries. So we
must reject such requests.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are hardware limitations on the number of available MSIs,
which firmware expresses using a property named "ibm,pe-total-#msi".
This property tells us how many MSIs are available for devices below
the point in the PCI tree where we find the property.
For old firmwares which don't have the property, we assume there are
8 MSIs available per "partitionable endpoint" (PE). The PE can be
found using existing EEH code, which uses the methods described in
PAPR. For our purposes we want the parent of the node that's
identified using this method.
When a driver requests n MSIs for a device, we first establish where
the "ibm,pe-total-#msi" property above that device is, or we find the
PE if the property is not found. In both cases we call this node
the "pe_dn".
We then count all non-bridge devices below the pe_dn, to establish
how many devices in total may need MSIs. The quota is then simply the
total available divided by the number of devices, if the request is
less than or equal to the quota, the request is fine and we're done.
If the request is greater than the quota, we try to determine if there
are any "spare" MSIs which we can give to this device. Spare MSIs are
found by looking for other devices which can never use their full
quota, because their "req#msi(-x)" property is less than the quota.
If we find any spare, we divide the spares by the number of devices
that could request more than their quota. This ensures the spare
MSIs are spread evenly amongst all over-quota requestors.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If a driver asks for more MSIs than the devices "req#msi(-x)" property,
we currently return -ENOSPC. This doesn't give the driver any chance to
make a new request with a number that might work.
So if "req#msi(-x)" is less than the request, return its value. To be
100% safe, make sure we return an error if req_msi == 0.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The EEH code disables and enables interrupts during the
device recovery process. This is unnecessary for MSI
and MSI-X interrupts because they are effectively disabled
by the DMA Stopped state when an EEH error occurs. The
current code is also incorrect for MSI-X interrupts. It
doesn't take into account that MSI-X interrupts are tracked
in a different way than LSI/MSI interrupts. This patch
ensures only LSI interrupts are disabled/enabled.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we can't allocate the requested number of MSIs, we can still tell the
generic code how many we were able to allocate. That can then be passed
onto the driver, allowing it to request that many in future, and
probably succeeed.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We also need to check that the device isn't using MSI-X in the irq fixup
routine, otherwise we might leave MSI-Xs configured at boot.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Firmware encodes the number of MSI-X requested by a device in a
different property than for MSI. Pull the property name out as a
parameter and share the logic for both cases.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to increment i in the loop that queries what interrupts firmware
gave us, otherwise we'll incorrectly use the first value over and over.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since we never hotplug add an isa bus, we never need to set primary.
Delete this write-only variable.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/platforms/pseries/hotplug-memory.c uses
remove_section_mapping() but doesn't include sparsemem.h which defines
it. This can cause compilation fails for some configs.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Convert arch/powerpc/ over to long long based u64:
-#ifdef __powerpc64__
-# include <asm-generic/int-l64.h>
-#else
-# include <asm-generic/int-ll64.h>
-#endif
+#include <asm-generic/int-ll64.h>
This will avoid reoccuring spurious warnings in core kernel code that
comes when people test on their own hardware. (i.e. x86 in ~98% of the
cases) This is what x86 uses and it generally helps keep 64-bit code
32-bit clean too.
[Adjusted to not impact user mode (from paulus) - sfr]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Impact: cleanup, update to new cpumask API
Irq_desc.affinity and irq_desc.pending_mask are now cpumask_var_t's
so access to them should be using the new cpumask API.
Signed-off-by: Mike Travis <travis@sgi.com>
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
* 'core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (63 commits)
stacktrace: provide save_stack_trace_tsk() weak alias
rcu: provide RCU options on non-preempt architectures too
printk: fix discarding message when recursion_bug
futex: clean up futex_(un)lock_pi fault handling
"Tree RCU": scalable classic RCU implementation
futex: rename field in futex_q to clarify single waiter semantics
x86/swiotlb: add default swiotlb_arch_range_needs_mapping
x86/swiotlb: add default phys<->bus conversion
x86: unify pci iommu setup and allow swiotlb to compile for 32 bit
x86: add swiotlb allocation functions
swiotlb: consolidate swiotlb info message printing
swiotlb: support bouncing of HighMem pages
swiotlb: factor out copy to/from device
swiotlb: add arch hook to force mapping
swiotlb: allow architectures to override phys<->bus<->phys conversions
swiotlb: add comment where we handle the overflow of a dma mask on 32 bit
rcu: fix rcutorture behavior during reboot
resources: skip sanity check of busy resources
swiotlb: move some definitions to header
swiotlb: allow architectures to override swiotlb pool allocation
...
Fix up trivial conflicts in
arch/x86/kernel/Makefile
arch/x86/mm/init_32.c
include/linux/hardirq.h
as per Ingo's suggestions.
Currently, pseries_cpu_die() calls msleep() while polling RTAS for
the status of the dying cpu.
However, if the cpu that is going down also happens to be the one
doing the tick then we're hosed as the tick_do_timer_cpu 'baton' is
only passed later on in tick_shutdown() when _cpu_down() does the
CPU_DEAD notification. Therefore jiffies won't be updated anymore.
This replaces that msleep() with a cpu_relax() to make sure we're not
going to schedule at that point.
With this patch my test box survives a 100k iterations hotplug stress
test on _all_ cpus, whereas without it, it quickly dies after ~50
iterations.
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Cc: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
