Generate a switchdev notification whenever an MST state changes. This
notification is keyed by the VLANs MSTI rather than the VID, since
multiple VLANs may share the same MST instance.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Whenever a VLAN moves to a new MSTI, send a switchdev notification so
that switchdevs can track a bridge's VID to MSTI mappings.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Trigger a switchdev event whenever the bridge's MST mode is
enabled/disabled. This allows constituent ports to either perform any
required hardware config, or refuse the change if it not supported.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the switchdev_handle_fdb_event_to_device() event replication helper
was created, my original thought was that FDB events on LAG interfaces
should most likely be special-cased, not just replicated towards all
switchdev ports beneath that LAG. So this replication helper currently
does not recurse through switchdev lower interfaces of LAG bridge ports,
but rather calls the lag_mod_cb() if that was provided.
No switchdev driver uses this helper for FDB events on LAG interfaces
yet, so that was an assumption which was yet to be tested. It is
certainly usable for that purpose, as my RFC series shows:
https://patchwork.kernel.org/project/netdevbpf/cover/20220210125201.2859463-1-vladimir.oltean@nxp.com/
however this approach is slightly convoluted because:
- the switchdev driver gets a "dev" that isn't its own net device, but
rather the LAG net device. It must call switchdev_lower_dev_find(dev)
in order to get a handle of any of its own net devices (the ones that
pass check_cb).
- in order for FDB entries on LAG ports to be correctly refcounted per
the number of switchdev ports beneath that LAG, we haven't escaped the
need to iterate through the LAG's lower interfaces. Except that is now
the responsibility of the switchdev driver, because the replication
helper just stopped half-way.
So, even though yes, FDB events on LAG bridge ports must be
special-cased, in the end it's simpler to let switchdev_handle_fdb_*
just iterate through the LAG port's switchdev lowers, and let the
switchdev driver figure out that those physical ports are under a LAG.
The switchdev_handle_fdb_event_to_device() helper takes a
"foreign_dev_check" callback so it can figure out whether @dev can
autonomously forward to @foreign_dev. DSA fills this method properly:
if the LAG is offloaded by another port in the same tree as @dev, then
it isn't foreign. If it is a software LAG, it is foreign - forwarding
happens in software.
Whether an interface is foreign or not decides whether the replication
helper will go through the LAG's switchdev lowers or not. Since the
lan966x doesn't properly fill this out, FDB events on software LAG
uppers will get called. By changing lan966x_foreign_dev_check(), we can
suppress them.
Whereas DSA will now start receiving FDB events for its offloaded LAG
uppers, so we need to return -EOPNOTSUPP, since we currently don't do
the right thing for them.
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The switchdev_handle_port_obj_add() helper is good for replicating a
port object on the lower interfaces of @dev, if that object was emitted
on a bridge, or on a bridge port that is a LAG.
However, drivers that use this helper limit themselves to a box from
which they can no longer intercept port objects notified on neighbor
ports ("foreign interfaces").
One such driver is DSA, where software bridging with foreign interfaces
such as standalone NICs or Wi-Fi APs is an important use case. There, a
VLAN installed on a neighbor bridge port roughly corresponds to a
forwarding VLAN installed on the DSA switch's CPU port.
To support this use case while also making use of the benefits of the
switchdev_handle_* replication helper for port objects, introduce a new
variant of these functions that crawls through the neighbor ports of
@dev, in search of potentially compatible switchdev ports that are
interested in the event.
The strategy is identical to switchdev_handle_fdb_event_to_device():
if @dev wasn't a switchdev interface, then go one step upper, and
recursively call this function on the bridge that this port belongs to.
At the next recursion step, __switchdev_handle_port_obj_add() will
iterate through the bridge's lower interfaces. Among those, some will be
switchdev interfaces, and one will be the original @dev that we came
from. To prevent infinite recursion, we must suppress reentry into the
original @dev, and just call the @add_cb for the switchdev_interfaces.
It looks like this:
br0
/ | \
/ | \
/ | \
swp0 swp1 eth0
1. __switchdev_handle_port_obj_add(eth0)
-> check_cb(eth0) returns false
-> eth0 has no lower interfaces
-> eth0's bridge is br0
-> switchdev_lower_dev_find(br0, check_cb, foreign_dev_check_cb))
finds br0
2. __switchdev_handle_port_obj_add(br0)
-> check_cb(br0) returns false
-> netdev_for_each_lower_dev
-> check_cb(swp0) returns true, so we don't skip this interface
3. __switchdev_handle_port_obj_add(swp0)
-> check_cb(swp0) returns true, so we call add_cb(swp0)
(back to netdev_for_each_lower_dev from 2)
-> check_cb(swp1) returns true, so we don't skip this interface
4. __switchdev_handle_port_obj_add(swp1)
-> check_cb(swp1) returns true, so we call add_cb(swp1)
(back to netdev_for_each_lower_dev from 2)
-> check_cb(eth0) returns false, so we skip this interface to
avoid infinite recursion
Note: eth0 could have been a LAG, and we don't want to suppress the
recursion through its lowers if those exist, so when check_cb() returns
false, we still call switchdev_lower_dev_find() to estimate whether
there's anything worth a recursion beneath that LAG. Using check_cb()
and foreign_dev_check_cb(), switchdev_lower_dev_find() not only figures
out whether the lowers of the LAG are switchdev, but also whether they
actively offload the LAG or not (whether the LAG is "foreign" to the
switchdev interface or not).
The port_obj_info->orig_dev is preserved across recursive calls, so
switchdev drivers still know on which device was this notification
originally emitted.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_switchdev_port_vlan_add() currently emits a SWITCHDEV_PORT_OBJ_ADD
event with a SWITCHDEV_OBJ_ID_PORT_VLAN for 2 distinct cases:
- a struct net_bridge_vlan got created
- an existing struct net_bridge_vlan was modified
This makes it impossible for switchdev drivers to properly balance
PORT_OBJ_ADD with PORT_OBJ_DEL events, so if we want to allow that to
happen, we must provide a way for drivers to distinguish between a
VLAN with changed flags and a new one.
Annotate struct switchdev_obj_port_vlan with a "bool changed" that
distinguishes the 2 cases above.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To reduce code churn, the same patch makes multiple changes, since they
all touch the same lines:
1. The implementations for these two are identical, just with different
function pointers. Reduce duplications and name the function pointers
"mod_cb" instead of "add_cb" and "del_cb". Pass the event as argument.
2. Drop the "const" attribute from "orig_dev". If the driver needs to
check whether orig_dev belongs to itself and then
call_switchdev_notifiers(orig_dev, SWITCHDEV_FDB_OFFLOADED), it
can't, because call_switchdev_notifiers takes a non-const struct
net_device *.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of explicit offloading API in switchdev in commit
2f5dc00f7a ("net: bridge: switchdev: let drivers inform which bridge
ports are offloaded"), we started having Ethernet switch drivers calling
directly into a function exported by net/bridge/br_switchdev.c, which is
a function exported by the bridge driver.
This means that drivers that did not have an explicit dependency on the
bridge before, like cpsw and am65-cpsw, now do - otherwise it is not
possible to call a symbol exported by a driver that can be built as
module unless you are a module too.
There was an attempt to solve the dependency issue in the form of commit
b0e8181762 ("net: build all switchdev drivers as modules when the
bridge is a module"). Grygorii Strashko, however, says about it:
| In my opinion, the problem is a bit bigger here than just fixing the
| build :(
|
| In case, of ^cpsw the switchdev mode is kinda optional and in many
| cases (especially for testing purposes, NFS) the multi-mac mode is
| still preferable mode.
|
| There were no such tight dependency between switchdev drivers and
| bridge core before and switchdev serviced as independent, notification
| based layer between them, so ^cpsw still can be "Y" and bridge can be
| "M". Now for mostly every kernel build configuration the CONFIG_BRIDGE
| will need to be set as "Y", or we will have to update drivers to
| support build with BRIDGE=n and maintain separate builds for
| networking vs non-networking testing. But is this enough? Wouldn't
| it cause 'chain reaction' required to add more and more "Y" options
| (like CONFIG_VLAN_8021Q)?
|
| PS. Just to be sure we on the same page - ARM builds will be forced
| (with this patch) to have CONFIG_TI_CPSW_SWITCHDEV=m and so all our
| automation testing will just fail with omap2plus_defconfig.
In the light of this, it would be desirable for some configurations to
avoid dependencies between switchdev drivers and the bridge, and have
the switchdev mode as completely optional within the driver.
Arnd Bergmann also tried to write a patch which better expressed the
build time dependency for Ethernet switch drivers where the switchdev
support is optional, like cpsw/am65-cpsw, and this made the drivers
follow the bridge (compile as module if the bridge is a module) only if
the optional switchdev support in the driver was enabled in the first
place:
https://patchwork.kernel.org/project/netdevbpf/patch/20210802144813.1152762-1-arnd@kernel.org/
but this still did not solve the fact that cpsw and am65-cpsw now must
be built as modules when the bridge is a module - it just expressed
correctly that optional dependency. But the new behavior is an apparent
regression from Grygorii's perspective.
So to support the use case where the Ethernet driver is built-in,
NET_SWITCHDEV (a bool option) is enabled, and the bridge is a module, we
need a framework that can handle the possible absence of the bridge from
the running system, i.e. runtime bloatware as opposed to build-time
bloatware.
Luckily we already have this framework, since switchdev has been using
it extensively. Events from the bridge side are transmitted to the
driver side using notifier chains - this was originally done so that
unrelated drivers could snoop for events emitted by the bridge towards
ports that are implemented by other drivers (think of a switch driver
with LAG offload that listens for switchdev events on a bonding/team
interface that it offloads).
There are also events which are transmitted from the driver side to the
bridge side, which again are modeled using notifiers.
SWITCHDEV_FDB_ADD_TO_BRIDGE is an example of this, and deals with
notifying the bridge that a MAC address has been dynamically learned.
So there is a precedent we can use for modeling the new framework.
The difference compared to SWITCHDEV_FDB_ADD_TO_BRIDGE is that the work
that the bridge needs to do when a port becomes offloaded is blocking in
its nature: replay VLANs, MDBs etc. The calling context is indeed
blocking (we are under rtnl_mutex), but the existing switchdev
notification chain that the bridge is subscribed to is only the atomic
one. So we need to subscribe the bridge to the blocking switchdev
notification chain too.
This patch:
- keeps the driver-side perception of the switchdev_bridge_port_{,un}offload
unchanged
- moves the implementation of switchdev_bridge_port_{,un}offload from
the bridge module into the switchdev module.
- makes everybody that is subscribed to the switchdev blocking notifier
chain "hear" offload & unoffload events
- makes the bridge driver subscribe and handle those events
- moves the bridge driver's handling of those events into 2 new
functions called br_switchdev_port_{,un}offload. These functions
contain in fact the core of the logic that was previously in
switchdev_bridge_port_{,un}offload, just that now we go through an
extra indirection layer to reach them.
Unlike all the other switchdev notification structures, the structure
used to carry the bridge port information, struct
switchdev_notifier_brport_info, does not contain a "bool handled".
This is because in the current usage pattern, we always know that a
switchdev bridge port offloading event will be handled by the bridge,
because the switchdev_bridge_port_offload() call was initiated by a
NETDEV_CHANGEUPPER event in the first place, where info->upper_dev is a
bridge. So if the bridge wasn't loaded, then the CHANGEUPPER event
couldn't have happened.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the semicolon at the end, the compiler sees the shim function as a
declaration and not as a definition, and warns:
'switchdev_handle_fdb_del_to_device' declared 'static' but never defined
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 8ca07176ab ("net: switchdev: introduce a fanout helper for SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently DSA has an issue with FDB entries pointing towards the bridge
in the presence of br_fdb_replay() being called at port join and leave
time.
In particular, each bridge port will ask for a replay for the FDB
entries pointing towards the bridge when it joins, and for another
replay when it leaves.
This means that for example, a bridge with 4 switch ports will notify
DSA 4 times of the bridge MAC address.
But if the MAC address of the bridge changes during the normal runtime
of the system, the bridge notifies switchdev [ once ] of the deletion of
the old MAC address as a local FDB towards the bridge, and of the
insertion [ again once ] of the new MAC address as a local FDB.
This is a problem, because DSA keeps the old MAC address as a host FDB
entry with refcount 4 (4 ports asked for it using br_fdb_replay). So the
old MAC address will not be deleted. Additionally, the new MAC address
will only be installed with refcount 1, and when the first switch port
leaves the bridge (leaving 3 others as still members), it will delete
with it the new MAC address of the bridge from the local FDB entries
kept by DSA (because the br_fdb_replay call on deletion will bring the
entry's refcount from 1 to 0).
So the problem, really, is that the number of br_fdb_replay() calls is
not matched with the refcount that a host FDB is offloaded to DSA during
normal runtime.
An elegant way to solve the problem would be to make the switchdev
notification emitted by br_fdb_change_mac_address() result in a host FDB
kept by DSA which has a refcount exactly equal to the number of ports
under that bridge. Then, no matter how many DSA ports join or leave that
bridge, the host FDB entry will always be deleted when there are exactly
zero remaining DSA switch ports members of the bridge.
To implement the proposed solution, we remember that the switchdev
objects and port attributes have some helpers provided by switchdev,
which can be optionally called by drivers:
switchdev_handle_port_obj_{add,del} and switchdev_handle_port_attr_set.
These helpers:
- fan out a switchdev object/attribute emitted for the bridge towards
all the lower interfaces that pass the check_cb().
- fan out a switchdev object/attribute emitted for a bridge port that is
a LAG towards all the lower interfaces that pass the check_cb().
In other words, this is the model we need for the FDB events too:
something that will keep an FDB entry emitted towards a physical port as
it is, but translate an FDB entry emitted towards the bridge into N FDB
entries, one per physical port.
Of course, there are many differences between fanning out a switchdev
object (VLAN) on 3 lower interfaces of a LAG and fanning out an FDB
entry on 3 lower interfaces of a LAG. Intuitively, an FDB entry towards
a LAG should be treated specially, because FDB entries are unicast, we
can't just install the same address towards 3 destinations. It is
imaginable that drivers might want to treat this case specifically, so
create some methods for this case and do not recurse into the LAG lower
ports, just the bridge ports.
DSA also listens for FDB entries on "foreign" interfaces, aka interfaces
bridged with us which are not part of our hardware domain: think an
Ethernet switch bridged with a Wi-Fi AP. For those addresses, DSA
installs host FDB entries. However, there we have the same problem
(those host FDB entries are installed with a refcount of only 1) and an
even bigger one which we did not have with FDB entries towards the
bridge:
br_fdb_replay() is currently not called for FDB entries on foreign
interfaces, just for the physical port and for the bridge itself.
So when DSA sniffs an address learned by the software bridge towards a
foreign interface like an e1000 port, and then that e1000 leaves the
bridge, DSA remains with the dangling host FDB address. That will be
fixed separately by replaying all FDB entries and not just the ones
towards the port and the bridge.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a bit difficult to understand what DSA checks when it tries to
avoid installing dynamically learned addresses on foreign interfaces as
local host addresses, so create a generic switchdev helper that can be
reused and is generally more readable.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case where the driver asks for a replay of a certain type of
event (port object or attribute) for a bridge port that is a LAG, it may
do so because this port has just joined the LAG.
But there might already be other switchdev ports in that LAG, and it is
preferable that those preexisting switchdev ports do not act upon the
replayed event.
The solution is to add a context to switchdev events, which is NULL most
of the time (when the bridge layer initiates the call) but which can be
set to a value controlled by the switchdev driver when a replay is
requested. The driver can then check the context to figure out if all
ports within the LAG should act upon the switchdev event, or just the
ones that match the context.
We have to modify all switchdev_handle_* helper functions as well as the
prototypes in the drivers that use these helpers too, because these
helpers hide the underlying struct switchdev_notifier_info from us and
there is no way to retrieve the context otherwise.
The context structure will be populated and used in later patches.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in bugfix commit 6ab4c3117a ("net: bridge: don't notify
switchdev for local FDB addresses") as well as in this discussion:
https://lore.kernel.org/netdev/20210117193009.io3nungdwuzmo5f7@skbuf/
the switchdev notifiers for FDB entries managed to have a zero-day bug,
which was that drivers would not know what to do with local FDB entries,
because they were not told that they are local. The bug fix was to
simply not notify them of those addresses.
Let us now add the 'is_local' bit to bridge FDB entries, and make all
drivers ignore these entries by their own choice.
Co-developed-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have a system with DSA ports, and udhcpcd is configured to bring
interfaces up as soon as they are created.
I create a bridge as follows:
ip link add br0 type bridge
As soon as I create the bridge and udhcpcd brings it up, I also have
avahi which automatically starts sending IPv6 packets to advertise some
local services, and because of that, the br0 bridge joins the following
IPv6 groups due to the code path detailed below:
33:33:ff:6d:c1:9c vid 0
33:33:00:00:00:6a vid 0
33:33:00:00:00:fb vid 0
br_dev_xmit
-> br_multicast_rcv
-> br_ip6_multicast_add_group
-> __br_multicast_add_group
-> br_multicast_host_join
-> br_mdb_notify
This is all fine, but inside br_mdb_notify we have br_mdb_switchdev_host
hooked up, and switchdev will attempt to offload the host joined groups
to an empty list of ports. Of course nobody offloads them.
Then when we add a port to br0:
ip link set swp0 master br0
the bridge doesn't replay the host-joined MDB entries from br_add_if,
and eventually the host joined addresses expire, and a switchdev
notification for deleting it is emitted, but surprise, the original
addition was already completely missed.
The strategy to address this problem is to replay the MDB entries (both
the port ones and the host joined ones) when the new port joins the
bridge, similar to what vxlan_fdb_replay does (in that case, its FDB can
be populated and only then attached to a bridge that you offload).
However there are 2 possibilities: the addresses can be 'pushed' by the
bridge into the port, or the port can 'pull' them from the bridge.
Considering that in the general case, the new port can be really late to
the party, and there may have been many other switchdev ports that
already received the initial notification, we would like to avoid
delivering duplicate events to them, since they might misbehave. And
currently, the bridge calls the entire switchdev notifier chain, whereas
for replaying it should just call the notifier block of the new guy.
But the bridge doesn't know what is the new guy's notifier block, it
just knows where the switchdev notifier chain is. So for simplification,
we make this a driver-initiated pull for now, and the notifier block is
passed as an argument.
To emulate the calling context for mdb objects (deferred and put on the
blocking notifier chain), we must iterate under RCU protection through
the bridge's mdb entries, queue them, and only call them once we're out
of the RCU read-side critical section.
There was some opportunity for reuse between br_mdb_switchdev_host_port,
br_mdb_notify and the newly added br_mdb_queue_one in how the switchdev
mdb object is created, so a helper was created.
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the member sw_backup to the structures switchdev_obj_ring_role_mrp
and switchdev_obj_in_role_mrp. In this way the SW can call the driver in
2 ways, once when sw_backup is set to false, meaning that the driver
should implement this completely in HW. And if that is not supported the
SW will call again but with sw_backup set to true, meaning that the
HW should help or allow the SW to run the protocol.
For example when role is MRM, if the HW can't detect when it stops
receiving MRP Test frames but it can trap these frames to CPU, then it
needs to return -EOPNOTSUPP when sw_backup is false and return 0 when
sw_backup is true.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove #IS_ENABLED(CONFIG_BRIDGE_MRP) from switchdev.h. This will
simplify the code implements MRP callbacks and will be similar with the
vlan filtering.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switchdev_port_attr_set function prototype was updated only for the
case where CONFIG_SWITCHDEV=y|m, leaving a prototype mismatch with the
stub definition for the disabled case. This results in a build error, so
update that function too.
Fixes: dcbdf1350e ("net: bridge: propagate extack through switchdev_port_attr_set")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The benefit is the ability to propagate errors from switchdev drivers
for the SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING and
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_PROTOCOL attributes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switchdev attribute offers a counterproductive API for a driver
writer, because although br_switchdev_set_port_flag gets passed a
"flags" and a "mask", those are passed piecemeal to the driver, so while
the PRE_BRIDGE_FLAGS listener knows what changed because it has the
"mask", the BRIDGE_FLAGS listener doesn't, because it only has the final
value. But certain drivers can offload only certain combinations of
settings, like for example they cannot change unicast flooding
independently of multicast flooding - they must be both on or both off.
The way the information is passed to switchdev makes drivers not
expressive enough, and unable to reject this request ahead of time, in
the PRE_BRIDGE_FLAGS notifier, so they are forced to reject it during
the deferred BRIDGE_FLAGS attribute, where the rejection is currently
ignored.
This patch also changes drivers to make use of the "mask" field for edge
detection when possible.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a struct switchdev_attr is notified through switchdev, there is no
way to report informational messages, unlike for struct switchdev_obj.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that MRP started to use also SWITCHDEV_ATTR_ID_PORT_STP_STATE to
notify HW, then SWITCHDEV_ATTR_ID_MRP_PORT_STAT is not used anywhere
else, therefore we can remove it.
Fixes: c284b54590 ("switchdev: mrp: Extend switchdev API to offload MRP")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all users of struct switchdev_trans have been modified to do
without it, we can remove this structure and the two helpers to determine
the phase.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the introduction of the switchdev API, port attributes were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.
Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8eceff ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.
It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.
This patch removes the struct switchdev_trans member from switchdev port
attribute notifier structures, and converts drivers to not look at this
member.
In part, this patch contains a revert of my previous commit 2e554a7a5d
("net: dsa: propagate switchdev vlan_filtering prepare phase to
drivers").
For the most part, the conversion was trivial except for:
- Rocker's world implementation based on Broadcom OF-DPA had an odd
implementation of ofdpa_port_attr_bridge_flags_set. The conversion was
done mechanically, by pasting the implementation twice, then only
keeping the code that would get executed during prepare phase on top,
then only keeping the code that gets executed during the commit phase
on bottom, then simplifying the resulting code until this was obtained.
- DSA's offloading of STP state, bridge flags, VLAN filtering and
multicast router could be converted right away. But the ageing time
could not, so a shim was introduced and this was left for a further
commit.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> # RTL8366RB
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the introduction of the switchdev API, port objects were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.
Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8eceff ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.
It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.
This patch removes the struct switchdev_trans member from switchdev port
object notifier structures, and converts drivers to not look at this
member.
Where driver conversion is trivial (like in the case of the Marvell
Prestera driver, NXP DPAA2 switch, TI CPSW, and Rocker drivers), it is
done in this patch.
Where driver conversion needs more attention (DSA, Mellanox Spectrum),
the conversion is left for subsequent patches and here we only fake the
prepare/commit phases at a lower level, just not in the switchdev
notifier itself.
Where the code has a natural structure that is best left alone as a
preparation and a commit phase (as in the case of the Ocelot switch),
that structure is left in place, just made to not depend upon the
switchdev transactional model.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The call path of a switchdev VLAN addition to the bridge looks something
like this today:
nbp_vlan_init
| __br_vlan_set_default_pvid
| | |
| | br_afspec |
| | | |
| | v |
| | br_process_vlan_info |
| | | |
| | v |
| | br_vlan_info |
| | / \ /
| | / \ /
| | / \ /
| | / \ /
v v v v v
nbp_vlan_add br_vlan_add ------+
| ^ ^ | |
| / | | |
| / / / |
\ br_vlan_get_master/ / v
\ ^ / / br_vlan_add_existing
\ | / / |
\ | / / /
\ | / / /
\ | / / /
\ | / / /
v | | v /
__vlan_add /
/ | /
/ | /
v | /
__vlan_vid_add | /
\ | /
v v v
br_switchdev_port_vlan_add
The ranges UAPI was introduced to the bridge in commit bdced7ef78
("bridge: support for multiple vlans and vlan ranges in setlink and
dellink requests") (Jan 10 2015). But the VLAN ranges (parsed in br_afspec)
have always been passed one by one, through struct bridge_vlan_info
tmp_vinfo, to br_vlan_info. So the range never went too far in depth.
Then Scott Feldman introduced the switchdev_port_bridge_setlink function
in commit 47f8328bb1 ("switchdev: add new switchdev bridge setlink").
That marked the introduction of the SWITCHDEV_OBJ_PORT_VLAN, which made
full use of the range. But switchdev_port_bridge_setlink was called like
this:
br_setlink
-> br_afspec
-> switchdev_port_bridge_setlink
Basically, the switchdev and the bridge code were not tightly integrated.
Then commit 41c498b935 ("bridge: restore br_setlink back to original")
came, and switchdev drivers were required to implement
.ndo_bridge_setlink = switchdev_port_bridge_setlink for a while.
In the meantime, commits such as 0944d6b5a2 ("bridge: try switchdev op
first in __vlan_vid_add/del") finally made switchdev penetrate the
br_vlan_info() barrier and start to develop the call path we have today.
But remember, br_vlan_info() still receives VLANs one by one.
Then Arkadi Sharshevsky refactored the switchdev API in 2017 in commit
29ab586c3d ("net: switchdev: Remove bridge bypass support from
switchdev") so that drivers would not implement .ndo_bridge_setlink any
longer. The switchdev_port_bridge_setlink also got deleted.
This refactoring removed the parallel bridge_setlink implementation from
switchdev, and left the only switchdev VLAN objects to be the ones
offloaded from __vlan_vid_add (basically RX filtering) and __vlan_add
(the latter coming from commit 9c86ce2c1a ("net: bridge: Notify about
bridge VLANs")).
That is to say, today the switchdev VLAN object ranges are not used in
the kernel. Refactoring the above call path is a bit complicated, when
the bridge VLAN call path is already a bit complicated.
Let's go off and finish the job of commit 29ab586c3d by deleting the
bogus iteration through the VLAN ranges from the drivers. Some aspects
of this feature never made too much sense in the first place. For
example, what is a range of VLANs all having the BRIDGE_VLAN_INFO_PVID
flag supposed to mean, when a port can obviously have a single pvid?
This particular configuration _is_ denied as of commit 6623c60dc2
("bridge: vlan: enforce no pvid flag in vlan ranges"), but from an API
perspective, the driver still has to play pretend, and only offload the
vlan->vid_end as pvid. And the addition of a switchdev VLAN object can
modify the flags of another, completely unrelated, switchdev VLAN
object! (a VLAN that is PVID will invalidate the PVID flag from whatever
other VLAN had previously been offloaded with switchdev and had that
flag. Yet switchdev never notifies about that change, drivers are
supposed to guess).
Nonetheless, having a VLAN range in the API makes error handling look
scarier than it really is - unwinding on errors and all of that.
When in reality, no one really calls this API with more than one VLAN.
It is all unnecessary complexity.
And despite appearing pretentious (two-phase transactional model and
all), the switchdev API is really sloppy because the VLAN addition and
removal operations are not paired with one another (you can add a VLAN
100 times and delete it just once). The bridge notifies through
switchdev of a VLAN addition not only when the flags of an existing VLAN
change, but also when nothing changes. There are switchdev drivers out
there who don't like adding a VLAN that has already been added, and
those checks don't really belong at driver level. But the fact that the
API contains ranges is yet another factor that prevents this from being
addressed in the future.
Of the existing switchdev pieces of hardware, it appears that only
Mellanox Spectrum supports offloading more than one VLAN at a time,
through mlxsw_sp_port_vlan_set. I have kept that code internal to the
driver, because there is some more bookkeeping that makes use of it, but
I deleted it from the switchdev API. But since the switchdev support for
ranges has already been de facto deleted by a Mellanox employee and
nobody noticed for 4 years, I'm going to assume it's not a biggie.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com> # switchdev and mlxsw
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drivers that support bridge offload need to be notified about changes to
the bridge's VLAN protocol so that they could react accordingly and
potentially veto the change.
Add a new switchdev attribute to communicate the change to drivers.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
so the switchdev can notifiy the bridge to flush non-permanent fdb entries
for this port. This is useful whenever the hardware fdb of the switchdev
is reset, but the netdev and the bridgeport are not deleted.
Note that this has the same effect as the IFLA_BRPORT_FLUSH attribute.
CC: Jiri Pirko <jiri@resnulli.us>
CC: Ivan Vecera <ivecera@redhat.com>
CC: Roopa Prabhu <roopa@nvidia.com>
CC: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend switchdev API to add support for MRP interconnect. The HW is
notified in the following cases:
SWITCHDEV_OBJ_ID_IN_ROLE_MRP: This is used when the interconnect role
of the node changes. The supported roles are MIM and MIC.
SWITCHDEV_OBJ_ID_IN_STATE_MRP: This is used when the interconnect ring
changes it states to open or closed.
SWITCHDEV_OBJ_ID_IN_TEST_MRP: This is used to start/stop sending
MRP_InTest frames on all MRP ports. This is called only on nodes that
have the interconnect role MIM.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A node that has the MRA role, it can behave as MRM or MRC.
Initially it starts as MRM and sends MRP_Test frames on both ring ports.
If it detects that there are MRP_Test send by another MRM, then it
checks if these frames have a lower priority than itself. In this case
it would send MRP_Nack frames to notify the other node that it needs to
stop sending MRP_Test frames.
If it receives a MRP_Nack frame then it stops sending MRP_Test frames
and starts to behave as a MRC but it would continue to monitor the
MRP_Test frames send by MRM. If at a point the MRM stops to send
MRP_Test frames it would get the MRM role and start to send MRP_Test
frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each MRP instance has a priority, a lower value means a higher priority.
The priority of MRP instance is stored in MRP_Test frame in this way
all the MRP nodes in the ring can see other nodes priority.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the variable mrp_ring_state from switchdev_attr because is not
used anywhere.
The ring state is set using SWITCHDEV_OBJ_ID_RING_STATE_MRP.
Fixes: c284b54590 ("switchdev: mrp: Extend switchdev API to offload MRP")
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend switchdev API to add support for MRP. The HW is notified in
following cases:
SWITCHDEV_OBJ_ID_MRP: This is used when a MRP instance is added/removed
from the MRP ring.
SWITCHDEV_OBJ_ID_RING_ROLE_MRP: This is used when the role of the node
changes. The current supported roles are MRM and MRC.
SWITCHDEV_OBJ_ID_RING_TEST_MRP: This is used when to start/stop sending
MRP_Test frames on the mrp ring ports. This is called only on nodes that have
the role MRM. In case this fails then the SW will generate the frames.
SWITCHDEV_OBJ_ID_RING_STATE_STATE: This is used when the ring changes it states
to open or closed. This is required to notify HW because the MRP_Test frame
contains the field MRP_InState which contains this information.
SWITCHDEV_ATTR_ID_MRP_PORT_STATE: This is used when the port's state is
changed. It can be in blocking/forwarding mode.
SWITCHDEV_ATTR_ID_MRP_PORT_ROLE: This is used when port's role changes. The
roles of the port can be primary/secondary. This is required to notify HW
because the MRP_Test frame contains the field MRP_PortRole that contains this
information.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are no more in tree users of the
switchdev_trans_item_{dequeue,enqueue} or switchdev_trans_item structure
in the kernel since commit 00fc0c51e3 ("rocker: Change world_ops API
and implementation to be switchdev independant").
Remove this unused code and update the documentation accordingly since.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have converted all possible callers to using a switchdev
notifier for attributes we do not have a need for implementing
switchdev_ops anymore, and this can be removed from all drivers the
net_device structure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing switchdev enabled drivers to veto specific
attribute settings from within the context of the caller, introduce a
new switchdev notifier type for port attributes.
Suggested-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have no more in tree users of switchdev_port_attr_get() after
d0e698d57a ("Merge branch 'net-Get-rid-of-switchdev_port_attr_get'")
so completely remove the function signature and body.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the bridge no longer calling switchdev_port_attr_get() to obtain
the supported bridge port flags from a driver but instead trying to set
the bridge port flags directly and relying on driver to reject
unsupported configurations, we can effectively get rid of
switchdev_port_attr_get() entirely since this was the only place where
it was called.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have converted the bridge code and the drivers to check for
bridge port(s) flags at the time we try to set them, there is no need
for a get() -> set() sequence anymore and
SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS_SUPPORT therefore becomes unused.
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for removing switchdev_port_attr_get(), introduce
PORT_PRE_BRIDGE_FLAGS which will be called through
switchdev_port_attr_set(), in the caller's context (possibly atomic) and
which must be checked by the switchdev driver in order to return whether
the operation is supported or not.
This is entirely analoguous to how the BRIDGE_FLAGS_SUPPORT works,
except it goes through a set() instead of get().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a dedicated NDO for getting a port's parent ID, get rid
of SWITCHDEV_ATTR_ID_PORT_PARENT_ID and convert all callers to use the
NDO exclusively. This is a preliminary change to getting rid of
switchdev_ops eventually.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch will enable vetoing of FDB entries. Make it possible
to communicate details of why an FDB entry is not acceptable back to the
user.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers use switchdev_handle_port_obj_add() to handle recursive descent
through lower devices. Change this function prototype to take add_cb
that itself takes an extack argument. Decode extack from
switchdev_notifier_port_obj_info and pass it to add_cb.
Update mlxsw and ocelot drivers which use this helper.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to pass extack to the drivers that need it, add an extack field
to struct switchdev_notifier_info, and an extack argument to the
function call_switchdev_blocking_notifiers(). Also add a helper function
switchdev_notifier_info_to_extack().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patch, bridge driver has extack argument available to
pass to switchdev. Therefore extend switchdev_port_obj_add() with this
argument, updating all callers, and passing the argument through to
switchdev_port_obj_notify().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop switchdev_ops.switchdev_port_obj_add and _del. Drop the uses of
this field from all clients, which were migrated to use switchdev
notification in the previous patches.
Add a new function switchdev_port_obj_notify() that sends the switchdev
notifications SWITCHDEV_PORT_OBJ_ADD and _DEL.
Update switchdev_port_obj_del_now() to dispatch to this new function.
Drop __switchdev_port_obj_add() and update switchdev_port_obj_add()
likewise.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the transition from switchdev operations to notifier chain (which
will take place in following patches), the onus is on the driver to find
its own devices below possible layer of LAG or other uppers.
The logic to do so is fairly repetitive: each driver is looking for its
own devices among the lowers of the notified device. For those that it
finds, it calls a handler. To indicate that the event was handled,
struct switchdev_notifier_port_obj_info.handled is set. The differences
lie only in what constitutes an "own" device and what handler to call.
Therefore abstract this logic into two helpers,
switchdev_handle_port_obj_add() and switchdev_handle_port_obj_del(). If
a driver only supports physical ports under a bridge device, it will
simply avoid this layer of indirection.
One area where this helper diverges from the current switchdev behavior
is the case of mixed lowers, some of which are switchdev ports and some
of which are not. Previously, such scenario would fail with -EOPNOTSUPP.
The helper could do that for lowers for which the passed-in predicate
doesn't hold. That would however break the case that switchdev ports
from several different drivers are stashed under one master, a scenario
that switchdev currently happily supports. Therefore tolerate any and
all unknown netdevices, whether they are backed by a switchdev driver
or not.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An offloading driver may need to have access to switchdev events on
ports that aren't directly under its control. An example is a VXLAN port
attached to a bridge offloaded by a driver. The driver needs to know
about VLANs configured on the VXLAN device. However the VXLAN device
isn't stashed between the bridge and a front-panel-port device (such as
is the case e.g. for LAG devices), so the usual switchdev ops don't
reach the driver.
VXLAN is likely not the only device type like this: in theory any L2
tunnel device that needs offloading will prompt requirement of this
sort. This falsifies the assumption that only the lower devices of a
front panel port need to be notified to achieve flawless offloading.
A way to fix this is to give up the notion of port object addition /
deletion as a switchdev operation, which assumes somewhat tight coupling
between the message producer and consumer. And instead send the message
over a notifier chain.
To that end, introduce two new switchdev notifier types,
SWITCHDEV_PORT_OBJ_ADD and SWITCHDEV_PORT_OBJ_DEL. These notifier types
communicate the same event as the corresponding switchdev op, except in
a form of a notification. struct switchdev_notifier_port_obj_info was
added to carry the fields that the switchdev op carries. An additional
field, handled, will be used to communicate back to switchdev that the
event has reached an interested party, which will be important for the
two-phase commit.
The two switchdev operations themselves are kept in place. Following
patches first convert individual clients to the notifier protocol, and
only then are the operations removed.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In general one can't assume that a switchdev notifier is called in a
non-atomic context, and correspondingly, the switchdev notifier chain is
an atomic one.
However, port object addition and deletion messages are delivered from a
process context. Even the MDB addition messages, whose delivery is
scheduled from atomic context, are queued and the delivery itself takes
place in blocking context. For VLAN messages in particular, keeping the
blocking nature is important for error reporting.
Therefore introduce a blocking notifier chain and related service
functions to distribute the notifications for which a blocking context
can be assumed.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
