Add a function that checks if a net device type is GTP.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Options are as follows: PDU_TYPE:QFI and they refernce to
the fields from the PDU Session Protocol. PDU Session data
is conveyed in GTP-U Extension Header.
GTP-U Extension Header is described in 3GPP TS 29.281.
PDU Session Protocol is described in 3GPP TS 38.415.
PDU_TYPE - indicates the type of the PDU Session Information (4 bits)
QFI - QoS Flow Identifier (6 bits)
# ip link add gtp_dev type gtp role sgsn
# tc qdisc add dev gtp_dev ingress
# tc filter add dev gtp_dev protocol ip parent ffff: \
flower \
enc_key_id 11 \
gtp_opts 1:8/ff:ff \
action mirred egress redirect dev eth0
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Adding GTP device through ip link creates the situation where
there is no userspace daemon which would handle GTP messages
(Echo Request for example). GTP-U instance which would not respond
to echo requests would violate GTP specification.
When GTP packet arrives with GTP_ECHO_REQ message type,
GTP_ECHO_RSP is send to the sender. GTP_ECHO_RSP message
should contain information element with GTPIE_RECOVERY tag and
restart counter value. For GTPv1 restart counter is not used
and should be equal to 0, for GTPv0 restart counter contains
information provided from userspace(IFLA_GTP_RESTART_COUNT).
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Suggested-by: Harald Welte <laforge@gnumonks.org>
Reviewed-by: Harald Welte <laforge@gnumonks.org>
Tested-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently in case of target hardware restart, we just reconfig and
re-enable the security keys and enable the network queues to start
data traffic back from where it was interrupted.
Many ath10k wifi chipsets have sequence numbers for the data
packets assigned by firmware and the mac sequence number will
restart from zero after target hardware restart leading to mismatch
in the sequence number expected by the remote peer vs the sequence
number of the frame sent by the target firmware.
This mismatch in sequence number will cause out-of-order packets
on the remote peer and all the frames sent by the device are dropped
until we reach the sequence number which was sent before we restarted
the target hardware
In order to fix this, we trigger a sta disconnect, in case of target
hw restart. After this there will be a fresh connection and thereby
avoiding the dropping of frames by remote peer.
The right fix would be to pull the entire data path into the host
which is not feasible or would need lots of complex changes and
will still be inefficient.
Tested on ath10k using WCN3990, QCA6174
Signed-off-by: Youghandhar Chintala <youghand@codeaurora.org>
Link: https://lore.kernel.org/r/20220308115325.5246-2-youghand@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Today's implementation of csum_shift() leads to branching based on
parity of 'offset'
000002f8 <csum_block_add>:
2f8: 70 a5 00 01 andi. r5,r5,1
2fc: 41 a2 00 08 beq 304 <csum_block_add+0xc>
300: 54 84 c0 3e rotlwi r4,r4,24
304: 7c 63 20 14 addc r3,r3,r4
308: 7c 63 01 94 addze r3,r3
30c: 4e 80 00 20 blr
Use first bit of 'offset' directly as input of the rotation instead of
branching.
000002f8 <csum_block_add>:
2f8: 54 a5 1f 38 rlwinm r5,r5,3,28,28
2fc: 20 a5 00 20 subfic r5,r5,32
300: 5c 84 28 3e rotlw r4,r4,r5
304: 7c 63 20 14 addc r3,r3,r4
308: 7c 63 01 94 addze r3,r3
30c: 4e 80 00 20 blr
And change to left shift instead of right shift to skip one more
instruction. This has no impact on the final sum.
000002f8 <csum_block_add>:
2f8: 54 a5 1f 38 rlwinm r5,r5,3,28,28
2fc: 5c 84 28 3e rotlw r4,r4,r5
300: 7c 63 20 14 addc r3,r3,r4
304: 7c 63 01 94 addze r3,r3
308: 4e 80 00 20 blr
Seems like only powerpc benefits from a branchless implementation.
Other main architectures like ARM or X86 get better code with
the generic implementation and its branch.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back when tcp_tso_autosize() and TCP pacing were introduced,
our focus was really to reduce burst sizes for long distance
flows.
The simple heuristic of using sk_pacing_rate/1024 has worked
well, but can lead to too small packets for hosts in the same
rack/cluster, when thousands of flows compete for the bottleneck.
Neal Cardwell had the idea of making the TSO burst size
a function of both sk_pacing_rate and tcp_min_rtt()
Indeed, for local flows, sending bigger bursts is better
to reduce cpu costs, as occasional losses can be repaired
quite fast.
This patch is based on Neal Cardwell implementation
done more than two years ago.
bbr is adjusting max_pacing_rate based on measured bandwidth,
while cubic would over estimate max_pacing_rate.
/proc/sys/net/ipv4/tcp_tso_rtt_log can be used to tune or disable
this new feature, in logarithmic steps.
Tested:
100Gbit NIC, two hosts in the same rack, 4K MTU.
600 flows rate-limited to 20000000 bytes per second.
Before patch: (TSO sizes would be limited to 20000000/1024/4096 -> 4 segments per TSO)
~# echo 0 >/proc/sys/net/ipv4/tcp_tso_rtt_log
~# nstat -n;perf stat ./super_netperf 600 -H otrv6 -l 20 -- -K dctcp -q 20000000;nstat|egrep "TcpInSegs|TcpOutSegs|TcpRetransSegs|Delivered"
96005
Performance counter stats for './super_netperf 600 -H otrv6 -l 20 -- -K dctcp -q 20000000':
65,945.29 msec task-clock # 2.845 CPUs utilized
1,314,632 context-switches # 19935.279 M/sec
5,292 cpu-migrations # 80.249 M/sec
940,641 page-faults # 14264.023 M/sec
201,117,030,926 cycles # 3049769.216 GHz (83.45%)
17,699,435,405 stalled-cycles-frontend # 8.80% frontend cycles idle (83.48%)
136,584,015,071 stalled-cycles-backend # 67.91% backend cycles idle (83.44%)
53,809,530,436 instructions # 0.27 insn per cycle
# 2.54 stalled cycles per insn (83.36%)
9,062,315,523 branches # 137422329.563 M/sec (83.22%)
153,008,621 branch-misses # 1.69% of all branches (83.32%)
23.182970846 seconds time elapsed
TcpInSegs 15648792 0.0
TcpOutSegs 58659110 0.0 # Average of 3.7 4K segments per TSO packet
TcpExtTCPDelivered 58654791 0.0
TcpExtTCPDeliveredCE 19 0.0
After patch:
~# echo 9 >/proc/sys/net/ipv4/tcp_tso_rtt_log
~# nstat -n;perf stat ./super_netperf 600 -H otrv6 -l 20 -- -K dctcp -q 20000000;nstat|egrep "TcpInSegs|TcpOutSegs|TcpRetransSegs|Delivered"
96046
Performance counter stats for './super_netperf 600 -H otrv6 -l 20 -- -K dctcp -q 20000000':
48,982.58 msec task-clock # 2.104 CPUs utilized
186,014 context-switches # 3797.599 M/sec
3,109 cpu-migrations # 63.472 M/sec
941,180 page-faults # 19214.814 M/sec
153,459,763,868 cycles # 3132982.807 GHz (83.56%)
12,069,861,356 stalled-cycles-frontend # 7.87% frontend cycles idle (83.32%)
120,485,917,953 stalled-cycles-backend # 78.51% backend cycles idle (83.24%)
36,803,672,106 instructions # 0.24 insn per cycle
# 3.27 stalled cycles per insn (83.18%)
5,947,266,275 branches # 121417383.427 M/sec (83.64%)
87,984,616 branch-misses # 1.48% of all branches (83.43%)
23.281200256 seconds time elapsed
TcpInSegs 1434706 0.0
TcpOutSegs 58883378 0.0 # Average of 41 4K segments per TSO packet
TcpExtTCPDelivered 58878971 0.0
TcpExtTCPDeliveredCE 9664 0.0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Link: https://lore.kernel.org/r/20220309015757.2532973-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Having the definitions of {__,}tls_driver_ctx() under an #if
guard means code referencing them also needs to rely on the
preprocessor. The protection doesn't appear needed so make the
definitions unconditional.
Fixes: db37bc177d ("net/funeth: add the data path")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When CONFIG_TCP_MD5SIG isn't enabled, there is a compilation bug due to
the fact that the static inline definition of tcp_inbound_md5_hash() has
an unexpected semicolon. Remove it.
Fixes: 1330b6ef33 ("skb: make drop reason booleanable")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220309122012.668986-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Steffen Klassert says:
====================
pull request (net): ipsec 2022-03-09
1) Fix IPv6 PMTU discovery for xfrm interfaces.
From Lina Wang.
2) Revert failing for policies and states that are
configured with XFRMA_IF_ID 0. It broke a
user configuration. From Kai Lueke.
3) Fix a possible buffer overflow in the ESP output path.
4) Fix ESP GSO for tunnel and BEET mode on inter address
family tunnels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a number of cases where function returns drop/no drop
decision as a boolean. Now that we want to report the reason
code as well we have to pass extra output arguments.
We can make the reason code evaluate correctly as bool.
I believe we're good to reorder the reasons as they are
reported to user space as strings.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Felix driver declares FDB isolation but puts all standalone ports in
VID 0. This is mostly problem-free as discussed with Alvin here:
https://patchwork.kernel.org/project/netdevbpf/cover/20220302191417.1288145-1-vladimir.oltean@nxp.com/#24763870
however there is one catch. DSA still thinks that FDB entries are
installed on the CPU port as many times as there are user ports, and
this is problematic when multiple user ports share the same MAC address.
Consider the default case where all user ports inherit their MAC address
from the DSA master, and then the user runs:
ip link set swp0 address 00:01:02:03:04:05
The above will make dsa_slave_set_mac_address() call
dsa_port_standalone_host_fdb_add() for 00:01:02:03:04:05 in port 0's
standalone database, and dsa_port_standalone_host_fdb_del() for the old
address of swp0, again in swp0's standalone database.
Both the ->port_fdb_add() and ->port_fdb_del() will be propagated down
to the felix driver, which will end up deleting the old MAC address from
the CPU port. But this is still in use by other user ports, so we end up
breaking unicast termination for them.
There isn't a problem in the fact that DSA keeps track of host
standalone addresses in the individual database of each user port: some
drivers like sja1105 need this. There also isn't a problem in the fact
that some drivers choose the same VID/FID for all standalone ports.
It is just that the deletion of these host addresses must be delayed
until they are known to not be in use any longer, and only the driver
has this knowledge. Since DSA keeps these addresses in &cpu_dp->fdbs and
&cpu_db->mdbs, it is just a matter of walking over those lists and see
whether the same MAC address is present on the CPU port in the port db
of another user port.
I have considered reusing the generic dsa_port_walk_fdbs() and
dsa_port_walk_mdbs() schemes for this, but locking makes it difficult.
In the ->port_fdb_add() method and co, &dp->addr_lists_lock is held, but
dsa_port_walk_fdbs() also acquires that lock. Also, even assuming that
we introduce an unlocked variant of the address iterator, we'd still
need some relatively complex data structures, and a void *ctx in the
dsa_fdb_walk_cb_t which we don't currently pass, such that drivers are
able to figure out, after iterating, whether the same MAC address is or
isn't present in the port db of another port.
All the above, plus the fact that I expect other drivers to follow the
same model as felix where all standalone ports use the same FID, made me
conclude that a generic method provided by DSA is necessary:
dsa_fdb_present_in_other_db() and the mdb equivalent. Felix calls this
from the ->port_fdb_del() handler for the CPU port, when the database
was classified to either a port db, or a LAG db.
For symmetry, we also call this from ->port_fdb_add(), because if the
address was installed once, then installing it a second time serves no
purpose: it's already in hardware in VID 0 and it affects all standalone
ports.
This change moves dsa_db_equal() from switch.c to dsa.c, since it now
has one more caller.
Fixes: 54c3198460 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was a prerequisite for the ill-fated
"netfilter: nat: force port remap to prevent shadowing well-known ports".
As this has been reverted, this change can be backed out too.
Signed-off-by: Florian Westphal <fw@strlen.de>
The maximum message size that can be send is bigger than
the maximum site that skb_page_frag_refill can allocate.
So it is possible to write beyond the allocated buffer.
Fix this by doing a fallback to COW in that case.
v2:
Avoid get get_order() costs as suggested by Linus Torvalds.
Fixes: cac2661c53 ("esp4: Avoid skb_cow_data whenever possible")
Fixes: 03e2a30f6a ("esp6: Avoid skb_cow_data whenever possible")
Reported-by: valis <sec@valis.email>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Realtek switches supports the same tag both before ethertype or between
payload and the CRC.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes attemting to print hdev->name directly which causes them to
print an error:
kernel: read_version:367: (efault): sock 000000006a3008f2
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use "flexible array members" for these cases. The older
style of one-element or zero-length arrays should no longer be used.
Reference:
https://www.kernel.org/doc/html/latest/process/deprecated.html#zero-length-and-one-element-arrays
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
While investigating on why a synchronize_net() has been added recently
in ipv6_mc_down(), I found that igmp6_event_query() and igmp6_event_report()
might drop skbs in some cases.
Discussion about removing synchronize_net() from ipv6_mc_down()
will happen in a different thread.
Fixes: f185de28d9 ("mld: add new workqueues for process mld events")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220303173728.937869-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A latter patch will postpone the delivery_time clearing until the stack
knows the skb is being delivered locally. That will allow other kernel
forwarding path (e.g. ip[6]_forward) to keep the delivery_time also.
An earlier attempt was to do skb_clear_delivery_time() in
ip_local_deliver() and ip6_input(). The discussion [0] requested
to move it one step later into ip_local_deliver_finish()
and ip6_input_finish() so that the delivery_time can be kept
for the ip_vs forwarding path also.
To do that, this patch also needs to take care of the (rcv) timestamp
usecase in ip_is_fragment(). It needs to expect delivery_time in
the skb->tstamp, so it needs to save the mono_delivery_time bit in
inet_frag_queue such that the delivery_time (if any) can be restored
in the final defragmented skb.
[Note that it will only happen when the locally generated skb is looping
from egress to ingress over a virtual interface (e.g. veth, loopback...),
skb->tstamp may have the delivery time before it is known that it will
be delivered locally and received by another sk.]
[0]: https://lore.kernel.org/netdev/ca728d81-80e8-3767-d5e-d44f6ad96e43@ssi.bg/
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "ocelot" and "ocelot-8021q" tagging protocols make use of different
hardware resources, and host FDB entries have different destination
ports in the switch analyzer module, practically speaking.
So when the user requests a tagging protocol change, the driver must
migrate all host FDB and MDB entries from the NPI port (in fact CPU port
module) towards the same physical port, but this time used as a regular
port.
It is pointless for the felix driver to keep a copy of the host
addresses, when we can create and export DSA helpers for walking through
the addresses that it already needs to keep on the CPU port, for
refcounting purposes.
felix_classify_db() is moved up to avoid a forward declaration.
We pass "bool change" because dp->fdbs and dp->mdbs are uninitialized
lists when felix_setup() first calls felix_set_tag_protocol(), so we
need to avoid calling dsa_port_walk_fdbs() during probe time.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a function page_pool_get_stats which can be used by drivers to obtain
stats for a specified page_pool.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add per-cpu stats tracking page pool recycling events:
- cached: recycling placed page in the page pool cache
- cache_full: page pool cache was full
- ring: page placed into the ptr ring
- ring_full: page released from page pool because the ptr ring was full
- released_refcnt: page released (and not recycled) because refcnt > 1
Signed-off-by: Joe Damato <jdamato@fastly.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add per-pool statistics counters for the allocation path of a page pool.
These stats are incremented in softirq context, so no locking or per-cpu
variables are needed.
This code is disabled by default and a kernel config option is provided for
users who wish to enable them.
The statistics added are:
- fast: successful fast path allocations
- slow: slow path order-0 allocations
- slow_high_order: slow path high order allocations
- empty: ptr ring is empty, so a slow path allocation was forced.
- refill: an allocation which triggered a refill of the cache
- waive: pages obtained from the ptr ring that cannot be added to
the cache due to a NUMA mismatch.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Use kfree_rcu(ptr, rcu) variant, using kfree_rcu(ptr) was not
intentional. From Eric Dumazet.
2) Use-after-free in netfilter hook core, from Eric Dumazet.
3) Missing rcu read lock side for netfilter egress hook,
from Florian Westphal.
4) nf_queue assume state->sk is full socket while it might not be.
Invoke sock_gen_put(), from Florian Westphal.
5) Add selftest to exercise the reported KASAN splat in 4)
6) Fix possible use-after-free in nf_queue in case sk_refcnt is 0.
Also from Florian.
7) Use input interface index only for hardware offload, not for
the software plane. This breaks tc ct action. Patch from Paul Blakey.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
net/sched: act_ct: Fix flow table lookup failure with no originating ifindex
netfilter: nf_queue: handle socket prefetch
netfilter: nf_queue: fix possible use-after-free
selftests: netfilter: add nfqueue TCP_NEW_SYN_RECV socket race test
netfilter: nf_queue: don't assume sk is full socket
netfilter: egress: silence egress hook lockdep splats
netfilter: fix use-after-free in __nf_register_net_hook()
netfilter: nf_tables: prefer kfree_rcu(ptr, rcu) variant
====================
Link: https://lore.kernel.org/r/20220301215337.378405-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After cited commit optimizted hw insertion, flow table entries are
populated with ifindex information which was intended to only be used
for HW offload. This tuple ifindex is hashed in the flow table key, so
it must be filled for lookup to be successful. But tuple ifindex is only
relevant for the netfilter flowtables (nft), so it's not filled in
act_ct flow table lookup, resulting in lookup failure, and no SW
offload and no offload teardown for TCP connection FIN/RST packets.
To fix this, add new tc ifindex field to tuple, which will
only be used for offloading, not for lookup, as it will not be
part of the tuple hash.
Fixes: 9795ded7f9 ("net/sched: act_ct: Fill offloading tuple iifidx")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This add a new sysctl: net.smc.autocorking_size
We can dynamically change the behaviour of autocorking
by change the value of autocorking_size.
Setting to 0 disables autocorking in SMC
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add sysctl interface to support container environment
for SMC as we talk in the mail list.
Link: https://lore.kernel.org/netdev/20220224020253.GF5443@linux.alibaba.com
Co-developed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
The sock_hold() side seems suspect, because there is no guarantee
that sk_refcnt is not already 0.
On failure, we cannot queue the packet and need to indicate an
error. The packet will be dropped by the caller.
v2: split skb prefetch hunk into separate change
Fixes: 271b72c7fa ("udp: RCU handling for Unicast packets.")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Add per-vni statistics for vni filter mode. Counting Rx/Tx
bytes/packets/drops/errors at the appropriate places.
This patch changes vxlan_vs_find_vni to also return the
vxlan_vni_node in cases where the vni belongs to a vni
filtering vxlan device
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds vnifiltering support to collect metadata device.
Motivation:
You can only use a single vxlan collect metadata device for a given
vxlan udp port in the system today. The vxlan collect metadata device
terminates all received vxlan packets. As shown in the below diagram,
there are use-cases where you need to support multiple such vxlan devices in
independent bridge domains. Each vxlan device must terminate the vni's
it is configured for.
Example usecase: In a service provider network a service provider
typically supports multiple bridge domains with overlapping vlans.
One bridge domain per customer. Vlans in each bridge domain are
mapped to globally unique vxlan ranges assigned to each customer.
vnifiltering support in collect metadata devices terminates only configured
vnis. This is similar to vlan filtering in bridge driver. The vni filtering
capability is provided by a new flag on collect metadata device.
In the below pic:
- customer1 is mapped to br1 bridge domain
- customer2 is mapped to br2 bridge domain
- customer1 vlan 10-11 is mapped to vni 1001-1002
- customer2 vlan 10-11 is mapped to vni 2001-2002
- br1 and br2 are vlan filtering bridges
- vxlan1 and vxlan2 are collect metadata devices with
vnifiltering enabled
┌──────────────────────────────────────────────────────────────────┐
│ switch │
│ │
│ ┌───────────┐ ┌───────────┐ │
│ │ │ │ │ │
│ │ br1 │ │ br2 │ │
│ └┬─────────┬┘ └──┬───────┬┘ │
│ vlans│ │ vlans │ │ │
│ 10,11│ │ 10,11│ │ │
│ │ vlanvnimap: │ vlanvnimap: │
│ │ 10-1001,11-1002 │ 10-2001,11-2002 │
│ │ │ │ │ │
│ ┌──────┴┐ ┌──┴─────────┐ ┌───┴────┐ │ │
│ │ swp1 │ │vxlan1 │ │ swp2 │ ┌┴─────────────┐ │
│ │ │ │ vnifilter:│ │ │ │vxlan2 │ │
│ └───┬───┘ │ 1001,1002│ └───┬────┘ │ vnifilter: │ │
│ │ └────────────┘ │ │ 2001,2002 │ │
│ │ │ └──────────────┘ │
│ │ │ │
└───────┼──────────────────────────────────┼───────────────────────┘
│ │
│ │
┌─────┴───────┐ │
│ customer1 │ ┌─────┴──────┐
│ host/VM │ │customer2 │
└─────────────┘ │ host/VM │
└────────────┘
With this implementation, vxlan dst metadata device can
be associated with range of vnis.
struct vxlan_vni_node is introduced to represent
a configured vni. We start with vni and its
associated remote_ip in this structure. This
structure can be extended to bring in other
per vni attributes if there are usecases for it.
A vni inherits an attribute from the base vxlan device
if there is no per vni attributes defined.
struct vxlan_dev gets a new rhashtable for
vnis called vxlan_vni_group. vxlan_vnifilter.c
implements the necessary netlink api, notifications
and helper functions to process and manage lifecycle
of vxlan_vni_node.
This patch also adds new helper functions in vxlan_multicast.c
to handle per vni remote_ip multicast groups which are part
of vxlan_vni_group.
Fix build problems:
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As more police parameters are passed to flow_offload, driver can check
them to make sure hardware handles packets in the way indicated by tc.
The conform-exceed control should be drop/pipe or drop/ok. Besides,
for drop/ok, the police should be the last action. As hardware can't
configure peakrate/avrate/overhead, offload should not be supported if
any of them is configured.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current police offload action entry is missing exceed/notexceed
actions and parameters that can be configured by tc police action.
Add the missing parameters as a pre-step for offloading police actions
to hardware.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As FDB isolation cannot be enforced between VLAN-aware bridges in lack
of hardware assistance like extra FID bits, it seems plausible that many
DSA switches cannot do it. Therefore, they need to reject configurations
with multiple VLAN-aware bridges from the two code paths that can
transition towards that state:
- joining a VLAN-aware bridge
- toggling VLAN awareness on an existing bridge
The .port_vlan_filtering method already propagates the netlink extack to
the driver, let's propagate it from .port_bridge_join too, to make sure
that the driver can use the same function for both.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For DSA, to encourage drivers to perform FDB isolation simply means to
track which bridge does each FDB and MDB entry belong to. It then
becomes the driver responsibility to use something that makes the FDB
entry from one bridge not match the FDB lookup of ports from other
bridges.
The top-level functions where the bridge is determined are:
- dsa_port_fdb_{add,del}
- dsa_port_host_fdb_{add,del}
- dsa_port_mdb_{add,del}
- dsa_port_host_mdb_{add,del}
aka the pre-crosschip-notifier functions.
Changing the API to pass a reference to a bridge is not superfluous, and
looking at the passed bridge argument is not the same as having the
driver look at dsa_to_port(ds, port)->bridge from the ->port_fdb_add()
method.
DSA installs FDB and MDB entries on shared (CPU and DSA) ports as well,
and those do not have any dp->bridge information to retrieve, because
they are not in any bridge - they are merely the pipes that serve the
user ports that are in one or multiple bridges.
The struct dsa_bridge associated with each FDB/MDB entry is encapsulated
in a larger "struct dsa_db" database. Although only databases associated
to bridges are notified for now, this API will be the starting point for
implementing IFF_UNICAST_FLT in DSA. There, the idea is to install FDB
entries on the CPU port which belong to the corresponding user port's
port database. These are supposed to match only when the port is
standalone.
It is better to introduce the API in its expected final form than to
introduce it for bridges first, then to have to change drivers which may
have made one or more assumptions.
Drivers can use the provided bridge.num, but they can also use a
different numbering scheme that is more convenient.
DSA must perform refcounting on the CPU and DSA ports by also taking
into account the bridge number. So if two bridges request the same local
address, DSA must notify the driver twice, once for each bridge.
In fact, if the driver supports FDB isolation, DSA must perform
refcounting per bridge, but if the driver doesn't, DSA must refcount
host addresses across all bridges, otherwise it would be telling the
driver to delete an FDB entry for a bridge and the driver would delete
it for all bridges. So introduce a bool fdb_isolation in drivers which
would make all bridge databases passed to the cross-chip notifier have
the same number (0). This makes dsa_mac_addr_find() -> dsa_db_equal()
say that all bridge databases are the same database - which is
essentially the legacy behavior.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
1) Fix PMTU for IPv6 if the reported MTU minus the ESP overhead is
smaller than 1280. From Jiri Bohac.
2) Fix xfrm interface ID and inter address family tunneling when
migrating xfrm states. From Yan Yan.
3) Add missing xfrm intrerface ID initialization on xfrmi_changelink.
From Antony Antony.
4) Enforce validity of xfrm offload input flags so that userspace can't
send undefined flags to the offload driver.
From Leon Romanovsky.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions do essentially the same work to verify TCP-MD5 sign.
Code can be merged into one family-independent function in order to
reduce copy'n'paste and generated code.
Later with TCP-AO option added, this will allow to create one function
that's responsible for segment verification, that will have all the
different checks for MD5/AO/non-signed packets, which in turn will help
to see checks for all corner-cases in one function, rather than spread
around different families and functions.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220223175740.452397-1-dima@arista.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This change introduces support for installing static FDB entries towards
a bridge port that is a LAG of multiple DSA switch ports, as well as
support for filtering towards the CPU local FDB entries emitted for LAG
interfaces that are bridge ports.
Conceptually, host addresses on LAG ports are identical to what we do
for plain bridge ports. Whereas FDB entries _towards_ a LAG can't simply
be replicated towards all member ports like we do for multicast, or VLAN.
Instead we need new driver API. Hardware usually considers a LAG to be a
"logical port", and sets the entire LAG as the forwarding destination.
The physical egress port selection within the LAG is made by hashing
policy, as usual.
To represent the logical port corresponding to the LAG, we pass by value
a copy of the dsa_lag structure to all switches in the tree that have at
least one port in that LAG.
To illustrate why a refcounted list of FDB entries is needed in struct
dsa_lag, it is enough to say that:
- a LAG may be a bridge port and may therefore receive FDB events even
while it isn't yet offloaded by any DSA interface
- DSA interfaces may be removed from a LAG while that is a bridge port;
we don't want FDB entries lingering around, but we don't want to
remove entries that are still in use, either
For all the cases below to work, the idea is to always keep an FDB entry
on a LAG with a reference count equal to the DSA member ports. So:
- if a port joins a LAG, it requests the bridge to replay the FDB, and
the FDB entries get created, or their refcount gets bumped by one
- if a port leaves a LAG, the FDB replay deletes or decrements refcount
by one
- if an FDB is installed towards a LAG with ports already present, that
entry is created (if it doesn't exist) and its refcount is bumped by
the amount of ports already present in the LAG
echo "Adding FDB entry to bond with existing ports"
ip link del bond0
ip link add bond0 type bond mode 802.3ad
ip link set swp1 down && ip link set swp1 master bond0 && ip link set swp1 up
ip link set swp2 down && ip link set swp2 master bond0 && ip link set swp2 up
ip link del br0
ip link add br0 type bridge
ip link set bond0 master br0
bridge fdb add dev bond0 00:01:02:03:04:05 master static
ip link del br0
ip link del bond0
echo "Adding FDB entry to empty bond"
ip link del bond0
ip link add bond0 type bond mode 802.3ad
ip link del br0
ip link add br0 type bridge
ip link set bond0 master br0
bridge fdb add dev bond0 00:01:02:03:04:05 master static
ip link set swp1 down && ip link set swp1 master bond0 && ip link set swp1 up
ip link set swp2 down && ip link set swp2 master bond0 && ip link set swp2 up
ip link del br0
ip link del bond0
echo "Adding FDB entry to empty bond, then removing ports one by one"
ip link del bond0
ip link add bond0 type bond mode 802.3ad
ip link del br0
ip link add br0 type bridge
ip link set bond0 master br0
bridge fdb add dev bond0 00:01:02:03:04:05 master static
ip link set swp1 down && ip link set swp1 master bond0 && ip link set swp1 up
ip link set swp2 down && ip link set swp2 master bond0 && ip link set swp2 up
ip link set swp1 nomaster
ip link set swp2 nomaster
ip link del br0
ip link del bond0
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the switchdev_handle_fdb_event_to_device() event replication helper
was created, my original thought was that FDB events on LAG interfaces
should most likely be special-cased, not just replicated towards all
switchdev ports beneath that LAG. So this replication helper currently
does not recurse through switchdev lower interfaces of LAG bridge ports,
but rather calls the lag_mod_cb() if that was provided.
No switchdev driver uses this helper for FDB events on LAG interfaces
yet, so that was an assumption which was yet to be tested. It is
certainly usable for that purpose, as my RFC series shows:
https://patchwork.kernel.org/project/netdevbpf/cover/20220210125201.2859463-1-vladimir.oltean@nxp.com/
however this approach is slightly convoluted because:
- the switchdev driver gets a "dev" that isn't its own net device, but
rather the LAG net device. It must call switchdev_lower_dev_find(dev)
in order to get a handle of any of its own net devices (the ones that
pass check_cb).
- in order for FDB entries on LAG ports to be correctly refcounted per
the number of switchdev ports beneath that LAG, we haven't escaped the
need to iterate through the LAG's lower interfaces. Except that is now
the responsibility of the switchdev driver, because the replication
helper just stopped half-way.
So, even though yes, FDB events on LAG bridge ports must be
special-cased, in the end it's simpler to let switchdev_handle_fdb_*
just iterate through the LAG port's switchdev lowers, and let the
switchdev driver figure out that those physical ports are under a LAG.
The switchdev_handle_fdb_event_to_device() helper takes a
"foreign_dev_check" callback so it can figure out whether @dev can
autonomously forward to @foreign_dev. DSA fills this method properly:
if the LAG is offloaded by another port in the same tree as @dev, then
it isn't foreign. If it is a software LAG, it is foreign - forwarding
happens in software.
Whether an interface is foreign or not decides whether the replication
helper will go through the LAG's switchdev lowers or not. Since the
lan966x doesn't properly fill this out, FDB events on software LAG
uppers will get called. By changing lan966x_foreign_dev_check(), we can
suppress them.
Whereas DSA will now start receiving FDB events for its offloaded LAG
uppers, so we need to return -EOPNOTSUPP, since we currently don't do
the right thing for them.
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The main purpose of this change is to create a data structure for a LAG
as seen by DSA. This is similar to what we have for bridging - we pass a
copy of this structure by value to ->port_lag_join and ->port_lag_leave.
For now we keep the lag_dev, id and a reference count in it. Future
patches will add a list of FDB entries for the LAG (these also need to
be refcounted to work properly).
The LAG structure is created using dsa_port_lag_create() and destroyed
using dsa_port_lag_destroy(), just like we have for bridging.
Because now, the dsa_lag itself is refcounted, we can simplify
dsa_lag_map() and dsa_lag_unmap(). These functions need to keep a LAG in
the dst->lags array only as long as at least one port uses it. The
refcounting logic inside those functions can be removed now - they are
called only when we should perform the operation.
dsa_lag_dev() is renamed to dsa_lag_by_id() and now returns the dsa_lag
structure instead of the lag_dev net_device.
dsa_lag_foreach_port() now takes the dsa_lag structure as argument.
dst->lags holds an array of dsa_lag structures.
dsa_lag_map() now also saves the dsa_lag->id value, so that linear
walking of dst->lags in drivers using dsa_lag_id() is no longer
necessary. They can just look at lag.id.
dsa_port_lag_id_get() is a helper, similar to dsa_port_bridge_num_get(),
which can be used by drivers to get the LAG ID assigned by DSA to a
given port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The DSA LAG API will be changed to become more similar with the bridge
data structures, where struct dsa_bridge holds an unsigned int num,
which is generated by DSA and is one-based. We have a similar thing
going with the DSA LAG, except that isn't stored anywhere, it is
calculated dynamically by dsa_lag_id() by iterating through dst->lags.
The idea of encoding an invalid (or not requested) LAG ID as zero for
the purpose of simplifying checks in drivers means that the LAG IDs
passed by DSA to drivers need to be one-based too. So back-and-forth
conversion is needed when indexing the dst->lags array, as well as in
drivers which assume a zero-based index.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of converting struct net_device *dp->lag_dev into a
struct dsa_lag *dp->lag, we need to rename, for consistency purposes,
all occurrences of the "lag" variable in the DSA core to "lag_dev".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When using hci_le_create_conn_sync it shall wait for the conn_timeout
since the connection complete may take longer than just 2 seconds.
Also fix the masking of HCI_EV_LE_ENHANCED_CONN_COMPLETE and
HCI_EV_LE_CONN_COMPLETE so they are never both set so we can predict
which one the controller will use in case of HCI_OP_LE_CREATE_CONN.
Fixes: 6cd29ec6ae ("Bluetooth: hci_sync: Wait for proper events when connecting LE")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since bt_skb_sendmmsg can be used with the likes of SOCK_STREAM it
shall return the partial chunks it could allocate instead of freeing
everything as otherwise it can cause problems like bellow.
Fixes: 81be03e026 ("Bluetooth: RFCOMM: Replace use of memcpy_from_msg with bt_skb_sendmmsg")
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://lore.kernel.org/r/d7206e12-1b99-c3be-84f4-df22af427ef5@molgen.mpg.de
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215594
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de> (Nokia N9 (MeeGo/Harmattan)
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
This is fixing up the use without proper initialization in patch 5/5
-o-
Hi,
The following patchset contains Netfilter fixes for net:
1) Missing #ifdef CONFIG_IP6_NF_IPTABLES in recent xt_socket fix.
2) Fix incorrect flow action array size in nf_tables.
3) Unregister flowtable hooks from netns exit path.
4) Fix missing limit object release, from Florian Westphal.
5) Memleak in nf_tables object update path, also from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add a new bonding option ns_ip6_target, which correspond
to the arp_ip_target. With this we set IPv6 targets and send IPv6 NS
request to determine the health of the link.
For other related options like the validation, we still use
arp_validate, and will change to ns_validate later.
Note: the sysfs configuration support was removed based on
https://lore.kernel.org/netdev/8863.1645071997@famine
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new bonding parameter ns_targets to store IPv6 address.
Add required bond_ns_send/rcv functions first before adding
IPv6 address option setting.
Add two functions bond_send/rcv_validate so we can send/recv
ARP and NS at the same time.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding an extra storage field for bond_opt_value so we can set large
bytes of data for bonding options in future, e.g. IPv6 address.
Define a new call bond_opt_initextra(). Also change the checking order of
__bond_opt_init() and check values first.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch separate NS message allocation steps from ndisc_send_ns(),
so it could be used in other places, like bonding, to allocate and
send IPv6 NS message.
Also export ndisc_send_skb() and ndisc_ns_create() for later bonding usage.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case user space sends a packet destined to a broadcast address when a
matching broadcast route is not configured, the kernel will create a
unicast neighbour entry that will never be resolved [1].
When the broadcast route is configured, the unicast neighbour entry will
not be invalidated and continue to linger, resulting in packets being
dropped.
Solve this by invalidating unresolved neighbour entries for broadcast
addresses after routes for these addresses are internally configured by
the kernel. This allows the kernel to create a broadcast neighbour entry
following the next route lookup.
Another possible solution that is more generic but also more complex is
to have the ARP code register a listener to the FIB notification chain
and invalidate matching neighbour entries upon the addition of broadcast
routes.
It is also possible to wave off the issue as a user space problem, but
it seems a bit excessive to expect user space to be that intimately
familiar with the inner workings of the FIB/neighbour kernel code.
[1] https://lore.kernel.org/netdev/55a04a8f-56f3-f73c-2aea-2195923f09d1@huawei.com/
Reported-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the address of drop_reason to tcp_add_backlog() to store the
reasons for skb drops when fails. Following drop reasons are
introduced:
SKB_DROP_REASON_SOCKET_BACKLOG
Reviewed-by: Mengen Sun <mengensun@tencent.com>
Reviewed-by: Hao Peng <flyingpeng@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
immediate verdict expression needs to allocate one slot in the flow offload
action array, however, immediate data expression does not need to do so.
fwd and dup expression need to allocate one slot, this is missing.
Add a new offload_action interface to report if this expression needs to
allocate one slot in the flow offload action array.
Fixes: be2861dc36 ("netfilter: nft_{fwd,dup}_netdev: add offload support")
Reported-and-tested-by: Nick Gregory <Nick.Gregory@Sophos.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
With drivers converted over to using phylink PCS, there is no need for
the struct dsa_switch member "pcs_poll" to exist anymore - there is a
flag in the struct phylink_pcs which indicates whether this PCS needs
to be polled which supersedes this.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we have mctp_address_ok(), which checks if an EID is in the
"valid" range of 8-254 inclusive. However, 0 and 255 may also be valid
addresses, depending on context. 0 is the NULL EID, which may be set
when physical addressing is used. 255 is valid as a destination address
for broadcasts.
This change renames mctp_address_ok to mctp_address_unicast, and adds
similar helpers for broadcast and null EIDs, which will be used in an
upcoming commit.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds a new protocol attribute to IPv4 and IPv6 addresses.
Inspiration was taken from the protocol attribute of routes. User space
applications like iproute2 can set/get the protocol with the Netlink API.
The attribute is stored as an 8-bit unsigned integer.
The protocol attribute is set by kernel for these categories:
- IPv4 and IPv6 loopback addresses
- IPv6 addresses generated from router announcements
- IPv6 link local addresses
User space may pass custom protocols, not defined by the kernel.
Grouping addresses on their origin is useful in scenarios where you want
to distinguish between addresses based on who added them, e.g. kernel
vs. user space.
Tagging addresses with a string label is an existing feature that could be
used as a solution. Unfortunately the max length of a label is
15 characters, and for compatibility reasons the label must be prefixed
with the name of the device followed by a colon. Since device names also
have a max length of 15 characters, only -1 characters is guaranteed to be
available for any origin tag, which is not that much.
A reference implementation of user space setting and getting protocols
is available for iproute2:
9a6ea18bd7
Signed-off-by: Jacques de Laval <Jacques.De.Laval@westermo.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220217150202.80802-1-Jacques.De.Laval@westermo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add DSA support for the phylink mac_select_pcs() method so DSA drivers
can return provide phylink with the appropriate PCS for the PHY
interface mode.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP sendmsg() can be lockless, this is causing all kinds
of data races.
This patch converts sk->sk_tskey to remove one of these races.
BUG: KCSAN: data-race in __ip_append_data / __ip_append_data
read to 0xffff8881035d4b6c of 4 bytes by task 8877 on cpu 1:
__ip_append_data+0x1c1/0x1de0 net/ipv4/ip_output.c:994
ip_make_skb+0x13f/0x2d0 net/ipv4/ip_output.c:1636
udp_sendmsg+0x12bd/0x14c0 net/ipv4/udp.c:1249
inet_sendmsg+0x5f/0x80 net/ipv4/af_inet.c:819
sock_sendmsg_nosec net/socket.c:705 [inline]
sock_sendmsg net/socket.c:725 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2413
___sys_sendmsg net/socket.c:2467 [inline]
__sys_sendmmsg+0x267/0x4c0 net/socket.c:2553
__do_sys_sendmmsg net/socket.c:2582 [inline]
__se_sys_sendmmsg net/socket.c:2579 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2579
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
write to 0xffff8881035d4b6c of 4 bytes by task 8880 on cpu 0:
__ip_append_data+0x1d8/0x1de0 net/ipv4/ip_output.c:994
ip_make_skb+0x13f/0x2d0 net/ipv4/ip_output.c:1636
udp_sendmsg+0x12bd/0x14c0 net/ipv4/udp.c:1249
inet_sendmsg+0x5f/0x80 net/ipv4/af_inet.c:819
sock_sendmsg_nosec net/socket.c:705 [inline]
sock_sendmsg net/socket.c:725 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2413
___sys_sendmsg net/socket.c:2467 [inline]
__sys_sendmmsg+0x267/0x4c0 net/socket.c:2553
__do_sys_sendmmsg net/socket.c:2582 [inline]
__se_sys_sendmmsg net/socket.c:2579 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2579
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x0000054d -> 0x0000054e
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 8880 Comm: syz-executor.5 Not tainted 5.17.0-rc2-syzkaller-00167-gdcb85f85fa6f-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 09c2d251b7 ("net-timestamp: add key to disambiguate concurrent datagrams")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the cited commit, sparse started complaining about:
../include/net/gro.h:58:1: warning: directive in macro's argument list
../include/net/gro.h:59:1: warning: directive in macro's argument list
Fix that by moving the defines out of the struct_group() macro.
Fixes: de5a1f3ce4 ("net: gro: minor optimization for dev_gro_receive()")
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Acked-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduced in commit cf96357303 ("net: dsa: Allow providing PHY
statistics from CPU port"), it appears these were never used.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220216193726.2926320-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a regular need in the kernel to provide a way to declare
having a dynamically sized set of trailing elements in a structure.
Kernel code should always use “flexible array members”[1] for these
cases. The older style of one-element or zero-length arrays should
no longer be used[2].
This code was transformed with the help of Coccinelle:
(next-20220214$ spatch --jobs $(getconf _NPROCESSORS_ONLN) --sp-file script.cocci --include-headers --dir . > output.patch)
@@
identifier S, member, array;
type T1, T2;
@@
struct S {
...
T1 member;
T2 array[
- 0
];
};
UAPI and wireless changes were intentionally excluded from this patch
and will be sent out separately.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/78
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Options parsing in now done from mptcp_incoming_options().
mptcp_parse_option() has been removed from mptcp.h when CONFIG_MPTCP is
defined but not when it is not.
Fixes: cfde141ea3 ("mptcp: move option parsing into mptcp_incoming_options()")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ipv6 flowlabels historically require a reservation before use.
Optionally in exclusive mode (e.g., user-private).
Commit 59c820b231 ("ipv6: elide flowlabel check if no exclusive
leases exist") introduced a fastpath that avoids this check when no
exclusive leases exist in the system, and thus any flowlabel use
will be granted.
That allows skipping the control operation to reserve a flowlabel
entirely. Though with a warning if the fast path fails:
This is an optimization. Robust applications still have to revert to
requesting leases if the fast path fails due to an exclusive lease.
Still, this is subtle. Better isolate network namespaces from each
other. Flowlabels are per-netns. Also record per-netns whether
exclusive leases are in use. Then behavior does not change based on
activity in other netns.
Changes
v2
- wrap in IS_ENABLED(CONFIG_IPV6) to avoid breakage if disabled
Fixes: 59c820b231 ("ipv6: elide flowlabel check if no exclusive leases exist")
Link: https://lore.kernel.org/netdev/MWHPR2201MB1072BCCCFCE779E4094837ACD0329@MWHPR2201MB1072.namprd22.prod.outlook.com/
Reported-by: Congyu Liu <liu3101@purdue.edu>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Tested-by: Congyu Liu <liu3101@purdue.edu>
Link: https://lore.kernel.org/r/20220215160037.1976072-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, DSA programs VLANs on shared (DSA and CPU) ports each time it
does so on user ports. This is good for basic functionality but has
several limitations:
- the VLAN group which must reach the CPU may be radically different
from the VLAN group that must be autonomously forwarded by the switch.
In other words, the admin may want to isolate noisy stations and avoid
traffic from them going to the control processor of the switch, where
it would just waste useless cycles. The bridge already supports
independent control of VLAN groups on bridge ports and on the bridge
itself, and when VLAN-aware, it will drop packets in software anyway
if their VID isn't added as a 'self' entry towards the bridge device.
- Replaying host FDB entries may depend, for some drivers like mv88e6xxx,
on replaying the host VLANs as well. The 2 VLAN groups are
approximately the same in most regular cases, but there are corner
cases when timing matters, and DSA's approximation of replicating
VLANs on shared ports simply does not work.
- If a user makes the bridge (implicitly the CPU port) join a VLAN by
accident, there is no way for the CPU port to isolate itself from that
noisy VLAN except by rebooting the system. This is because for each
VLAN added on a user port, DSA will add it on shared ports too, but
for each VLAN deletion on a user port, it will remain installed on
shared ports, since DSA has no good indication of whether the VLAN is
still in use or not.
Now that the bridge driver emits well-balanced SWITCHDEV_OBJ_ID_PORT_VLAN
addition and removal events, DSA has a simple and straightforward task
of separating the bridge port VLANs (these have an orig_dev which is a
DSA slave interface, or a LAG interface) from the host VLANs (these have
an orig_dev which is a bridge interface), and to keep a simple reference
count of each VID on each shared port.
Forwarding VLANs must be installed on the bridge ports and on all DSA
ports interconnecting them. We don't have a good view of the exact
topology, so we simply install forwarding VLANs on all DSA ports, which
is what has been done until now.
Host VLANs must be installed primarily on the dedicated CPU port of each
bridge port. More subtly, they must also be installed on upstream-facing
and downstream-facing DSA ports that are connecting the bridge ports and
the CPU. This ensures that the mv88e6xxx's problem (VID of host FDB
entry may be absent from VTU) is still addressed even if that switch is
in a cross-chip setup, and it has no local CPU port.
Therefore:
- user ports contain only bridge port (forwarding) VLANs, and no
refcounting is necessary
- DSA ports contain both forwarding and host VLANs. Refcounting is
necessary among these 2 types.
- CPU ports contain only host VLANs. Refcounting is also necessary.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switchdev_handle_port_obj_add() helper is good for replicating a
port object on the lower interfaces of @dev, if that object was emitted
on a bridge, or on a bridge port that is a LAG.
However, drivers that use this helper limit themselves to a box from
which they can no longer intercept port objects notified on neighbor
ports ("foreign interfaces").
One such driver is DSA, where software bridging with foreign interfaces
such as standalone NICs or Wi-Fi APs is an important use case. There, a
VLAN installed on a neighbor bridge port roughly corresponds to a
forwarding VLAN installed on the DSA switch's CPU port.
To support this use case while also making use of the benefits of the
switchdev_handle_* replication helper for port objects, introduce a new
variant of these functions that crawls through the neighbor ports of
@dev, in search of potentially compatible switchdev ports that are
interested in the event.
The strategy is identical to switchdev_handle_fdb_event_to_device():
if @dev wasn't a switchdev interface, then go one step upper, and
recursively call this function on the bridge that this port belongs to.
At the next recursion step, __switchdev_handle_port_obj_add() will
iterate through the bridge's lower interfaces. Among those, some will be
switchdev interfaces, and one will be the original @dev that we came
from. To prevent infinite recursion, we must suppress reentry into the
original @dev, and just call the @add_cb for the switchdev_interfaces.
It looks like this:
br0
/ | \
/ | \
/ | \
swp0 swp1 eth0
1. __switchdev_handle_port_obj_add(eth0)
-> check_cb(eth0) returns false
-> eth0 has no lower interfaces
-> eth0's bridge is br0
-> switchdev_lower_dev_find(br0, check_cb, foreign_dev_check_cb))
finds br0
2. __switchdev_handle_port_obj_add(br0)
-> check_cb(br0) returns false
-> netdev_for_each_lower_dev
-> check_cb(swp0) returns true, so we don't skip this interface
3. __switchdev_handle_port_obj_add(swp0)
-> check_cb(swp0) returns true, so we call add_cb(swp0)
(back to netdev_for_each_lower_dev from 2)
-> check_cb(swp1) returns true, so we don't skip this interface
4. __switchdev_handle_port_obj_add(swp1)
-> check_cb(swp1) returns true, so we call add_cb(swp1)
(back to netdev_for_each_lower_dev from 2)
-> check_cb(eth0) returns false, so we skip this interface to
avoid infinite recursion
Note: eth0 could have been a LAG, and we don't want to suppress the
recursion through its lowers if those exist, so when check_cb() returns
false, we still call switchdev_lower_dev_find() to estimate whether
there's anything worth a recursion beneath that LAG. Using check_cb()
and foreign_dev_check_cb(), switchdev_lower_dev_find() not only figures
out whether the lowers of the LAG are switchdev, but also whether they
actively offload the LAG or not (whether the LAG is "foreign" to the
switchdev interface or not).
The port_obj_info->orig_dev is preserved across recursive calls, so
switchdev drivers still know on which device was this notification
originally emitted.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_switchdev_port_vlan_add() currently emits a SWITCHDEV_PORT_OBJ_ADD
event with a SWITCHDEV_OBJ_ID_PORT_VLAN for 2 distinct cases:
- a struct net_bridge_vlan got created
- an existing struct net_bridge_vlan was modified
This makes it impossible for switchdev drivers to properly balance
PORT_OBJ_ADD with PORT_OBJ_DEL events, so if we want to allow that to
happen, we must provide a way for drivers to distinguish between a
VLAN with changed flags and a new one.
Annotate struct switchdev_obj_port_vlan with a "bool changed" that
distinguishes the 2 cases above.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx is special among DSA drivers in that it requires the VTU to
contain the VID of the FDB entry it modifies in
mv88e6xxx_port_db_load_purge(), otherwise it will return -EOPNOTSUPP.
Sometimes due to races this is not always satisfied even if external
code does everything right (first deletes the FDB entries, then the
VLAN), because DSA commits to hardware FDB entries asynchronously since
commit c9eb3e0f87 ("net: dsa: Add support for learning FDB through
notification").
Therefore, the mv88e6xxx driver must close this race condition by
itself, by asking DSA to flush the switchdev workqueue of any FDB
deletions in progress, prior to exiting a VLAN.
Fixes: c9eb3e0f87 ("net: dsa: Add support for learning FDB through notification")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of patches for v5.18, with both wireless and stack patches.
rtw89 now has AP mode support and wcn36xx has survey support. But
otherwise pretty normal.
Major changes:
ath11k
* add LDPC FEC type in 802.11 radiotap header
* enable RX PPDU stats in monitor co-exist mode
wcn36xx
* implement survey reporting
brcmfmac
* add CYW43570 PCIE device
rtw88
* rtw8821c: enable RFE 6 devices
rtw89
* AP mode support
mt76
* mt7916 support
* background radar detection support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmIGLrkRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZsgWAf/aQb18PB2Wh+tH4qxkNW6jK3zfYSRDbDQ
QvrHcnN4BINorTLcGDvWqw3VANiETCW6mVBG8BWo1NyAlvkNziKaAFI3xVhuOE38
6d+wRVElG9JHeb6OwWCX2vWJmqWVxmEIAkTQrqT9VSSUjGDpS1mc3dAssABeEZhn
yzSKJomSRaRv/aC2f/4eYPAyeMUIZbN3VWFOvElGPls0mdrSBmt9OhAKkf3A3E0M
PuJzhnHgoKhpZ/Gmn+IrDZGC/RkUOfT2zZ5gUK0GVvpTFg2/80ilC7RJk2iF5Ibs
xGuRN9WSo9xWILF3SyRgrrx3ocZG0H2dvkJj4ZQbR485U8iXa+HC1g==
=AUlw
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-02-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
wireless-next patches for v5.18
First set of patches for v5.18, with both wireless and stack patches.
rtw89 now has AP mode support and wcn36xx has survey support. But
otherwise pretty normal.
Major changes:
ath11k
* add LDPC FEC type in 802.11 radiotap header
* enable RX PPDU stats in monitor co-exist mode
wcn36xx
* implement survey reporting
brcmfmac
* add CYW43570 PCIE device
rtw88
* rtw8821c: enable RFE 6 devices
rtw89
* AP mode support
mt76
* mt7916 support
* background radar detection support
This counter has never been visible, there is little point
trying to maintain it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we can control SMC handshake limitation through socket options,
which means that applications who need it must modify their code. It's
quite troublesome for many existing applications. This patch modifies
the global default value of SMC handshake limitation through netlink,
providing a way to put constraint on handshake without modifies any code
for applications.
Suggested-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having to acquire rtnl from netdev_run_todo() for every dismantled
device is not desirable when/if rtnl is under stress.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As depicted in the IEEE 802.15.4 specification, modulation/bands are
tight to a number of page/channels so we can for most of them derive the
durations automatically.
The two locations that must call this new helper to set the variou
symbol durations are:
- when manually requesting a channel change though the netlink interface
- at PHY creation, once the device driver has set the default
page/channel
If an information is missing, the symbol duration is not touched, a
debug message is eventually printed. This keeps the compatibility with
the unconverted drivers for which it was too complicated for me to find
their precise information. If they initially provided a symbol duration,
it would be kept. If they don't, the symbol duration value is left
untouched.
Once the symbol duration derived, the lifs and sifs durations are
updated as well.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220201180629.93410-4-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Tdsym is often given in the spec as pretty small numbers in microseconds
and hence was reflected in the code as symbol_duration and was stored as
a u8. Actually, for UWB PHYs, the symbol duration is given in
nanoseconds and are as precise as picoseconds. In order to handle better
these PHYs, change the type of symbol_duration to u32 and store this
value in nanoseconds.
All the users of this variable are updated in a mechanical way.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220201180629.93410-3-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Stefan Schmidt says:
====================
pull-request: ieee802154-next 2022-02-10
An update from ieee802154 for your *net-next* tree.
There is more ongoing in ieee802154 than usual. This will be the first pull
request for this cycle, but I expect one more. Depending on review and rework
times.
Pavel Skripkin ported the atusb driver over to the new USB api to avoid unint
problems as well as making use of the modern api without kmalloc() needs in he
driver.
Miquel Raynal landed some changes to ensure proper frame checksum checking with
hwsim, documenting our use of wake and stop_queue and eliding a magic value by
using the proper define.
David Girault documented the address struct used in ieee802154.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
1) Conntrack sets on CHECKSUM_UNNECESSARY for UDP packet with no checksum,
from Kevin Mitchell.
2) skb->priority support for nfqueue, from Nicolas Dichtel.
3) Remove conntrack extension register API, from Florian Westphal.
4) Move nat destroy hook to nf_nat_hook instead, to remove
nf_ct_ext_destroy(), also from Florian.
5) Wrap pptp conntrack NAT hooks into single structure, from Florian Westphal.
6) Support for tcp option set to noop for nf_tables, also from Florian.
7) Do not run x_tables comment match from packet path in nf_tables,
from Florian Westphal.
8) Replace spinlock by cmpxchg() loop to update missed ct event,
from Florian Westphal.
9) Wrap cttimeout hooks into single structure, from Florian.
10) Add fast nft_cmp expression for up to 16-bytes.
11) Use cb->ctx to store context in ctnetlink dump, instead of using
cb->args[], from Florian Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: ctnetlink: use dump structure instead of raw args
nfqueue: enable to set skb->priority
netfilter: nft_cmp: optimize comparison for 16-bytes
netfilter: cttimeout: use option structure
netfilter: ecache: don't use nf_conn spinlock
netfilter: nft_compat: suppress comment match
netfilter: exthdr: add support for tcp option removal
netfilter: conntrack: pptp: use single option structure
netfilter: conntrack: remove extension register api
netfilter: conntrack: handle ->destroy hook via nat_ops instead
netfilter: conntrack: move extension sizes into core
netfilter: conntrack: make all extensions 8-byte alignned
netfilter: nfqueue: enable to get skb->priority
netfilter: conntrack: mark UDP zero checksum as CHECKSUM_UNNECESSARY
====================
Link: https://lore.kernel.org/r/20220209133616.165104-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2022-02-09
We've added 126 non-merge commits during the last 16 day(s) which contain
a total of 201 files changed, 4049 insertions(+), 2215 deletions(-).
The main changes are:
1) Add custom BPF allocator for JITs that pack multiple programs into a huge
page to reduce iTLB pressure, from Song Liu.
2) Add __user tagging support in vmlinux BTF and utilize it from BPF
verifier when generating loads, from Yonghong Song.
3) Add per-socket fast path check guarding from cgroup/BPF overhead when
used by only some sockets, from Pavel Begunkov.
4) Continued libbpf deprecation work of APIs/features and removal of their
usage from samples, selftests, libbpf & bpftool, from Andrii Nakryiko
and various others.
5) Improve BPF instruction set documentation by adding byte swap
instructions and cleaning up load/store section, from Christoph Hellwig.
6) Switch BPF preload infra to light skeleton and remove libbpf dependency
from it, from Alexei Starovoitov.
7) Fix architecture-agnostic macros in libbpf for accessing syscall
arguments from BPF progs for non-x86 architectures,
from Ilya Leoshkevich.
8) Rework port members in struct bpf_sk_lookup and struct bpf_sock to be
of 16-bit field with anonymous zero padding, from Jakub Sitnicki.
9) Add new bpf_copy_from_user_task() helper to read memory from a different
task than current. Add ability to create sleepable BPF iterator progs,
from Kenny Yu.
10) Implement XSK batching for ice's zero-copy driver used by AF_XDP and
utilize TX batching API from XSK buffer pool, from Maciej Fijalkowski.
11) Generate temporary netns names for BPF selftests to avoid naming
collisions, from Hangbin Liu.
12) Implement bpf_core_types_are_compat() with limited recursion for
in-kernel usage, from Matteo Croce.
13) Simplify pahole version detection and finally enable CONFIG_DEBUG_INFO_DWARF5
to be selected with CONFIG_DEBUG_INFO_BTF, from Nathan Chancellor.
14) Misc minor fixes to libbpf and selftests from various folks.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (126 commits)
selftests/bpf: Cover 4-byte load from remote_port in bpf_sk_lookup
bpf: Make remote_port field in struct bpf_sk_lookup 16-bit wide
libbpf: Fix compilation warning due to mismatched printf format
selftests/bpf: Test BPF_KPROBE_SYSCALL macro
libbpf: Add BPF_KPROBE_SYSCALL macro
libbpf: Fix accessing the first syscall argument on s390
libbpf: Fix accessing the first syscall argument on arm64
libbpf: Allow overriding PT_REGS_PARM1{_CORE}_SYSCALL
selftests/bpf: Skip test_bpf_syscall_macro's syscall_arg1 on arm64 and s390
libbpf: Fix accessing syscall arguments on riscv
libbpf: Fix riscv register names
libbpf: Fix accessing syscall arguments on powerpc
selftests/bpf: Use PT_REGS_SYSCALL_REGS in bpf_syscall_macro
libbpf: Add PT_REGS_SYSCALL_REGS macro
selftests/bpf: Fix an endianness issue in bpf_syscall_macro test
bpf: Fix bpf_prog_pack build HPAGE_PMD_SIZE
bpf: Fix leftover header->pages in sparc and powerpc code.
libbpf: Fix signedness bug in btf_dump_array_data()
selftests/bpf: Do not export subtest as standalone test
bpf, x86_64: Fail gracefully on bpf_jit_binary_pack_finalize failures
...
====================
Link: https://lore.kernel.org/r/20220209210050.8425-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This change adds a couple of new ioctls for mctp sockets:
SIOCMCTPALLOCTAG and SIOCMCTPDROPTAG. These ioctls provide facilities
for explicit allocation / release of tags, overriding the automatic
allocate-on-send/release-on-reply and timeout behaviours. This allows
userspace more control over messages that may not fit a simple
request/response model.
In order to indicate a pre-allocated tag to the sendmsg() syscall, we
introduce a new flag to the struct sockaddr_mctp.smctp_tag value:
MCTP_TAG_PREALLOC.
Additional changes from Jeremy Kerr <jk@codeconstruct.com.au>.
Contains a fix that was:
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we have a couple of paths that check that an EID matches, or
the match value is MCTP_ADDR_ANY.
Rather than open coding this, add a little helper.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When uncloning an skb dst and its associated metadata, a new
dst+metadata is allocated and later replaces the old one in the skb.
This is helpful to have a non-shared dst+metadata attached to a specific
skb.
The issue is the uncloned dst+metadata is initialized with a refcount of
1, which is increased to 2 before attaching it to the skb. When
tun_dst_unclone returns, the dst+metadata is only referenced from a
single place (the skb) while its refcount is 2. Its refcount will never
drop to 0 (when the skb is consumed), leading to a memory leak.
Fix this by removing the call to dst_hold in tun_dst_unclone, as the
dst+metadata refcount is already 1.
Fixes: fc4099f172 ("openvswitch: Fix egress tunnel info.")
Cc: Pravin B Shelar <pshelar@ovn.org>
Reported-by: Vlad Buslov <vladbu@nvidia.com>
Tested-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When uncloning an skb dst and its associated metadata a new dst+metadata
is allocated and the tunnel information from the old metadata is copied
over there.
The issue is the tunnel metadata has references to cached dst, which are
copied along the way. When a dst+metadata refcount drops to 0 the
metadata is freed including the cached dst entries. As they are also
referenced in the initial dst+metadata, this ends up in UaFs.
In practice the above did not happen because of another issue, the
dst+metadata was never freed because its refcount never dropped to 0
(this will be fixed in a subsequent patch).
Fix this by initializing the dst cache after copying the tunnel
information from the old metadata to also unshare the dst cache.
Fixes: d71785ffc7 ("net: add dst_cache to ovs vxlan lwtunnel")
Cc: Paolo Abeni <pabeni@redhat.com>
Reported-by: Vlad Buslov <vladbu@nvidia.com>
Tested-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow up to 16-byte comparisons with a new cmp fast version. Use two
64-bit words and calculate the mask representing the bits to be
compared. Make sure the comparison is 64-bit aligned and avoid
out-of-bound memory access on registers.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Instead of two exported functions, export a single option structure.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
For updating eache missed value we can use cmpxchg.
This also avoids need to disable BH.
kernel robot reported build failure on v1 because not all arches support
cmpxchg for u16, so extend this to u32.
This doesn't increase struct size, existing padding is used.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Next step for using per netns inet6_addr_lst
is to have per netns work item to ultimately
call addrconf_verify_rtnl() and addrconf_verify()
with a new 'struct net*' argument.
Everything is still using the global inet6_addr_lst[] table.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a per netns hash table and a dedicated spinlock,
first step to get rid of the global inet6_addr_lst[] one.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the new dscp_t type to replace the fc_tos field of fib_config, to
ensure IPv4 routes aren't influenced by ECN bits when configured with
non-zero rtm_tos.
Before this patch, IPv4 routes specifying an rtm_tos with some of the
ECN bits set were accepted. However they wouldn't work (never match) as
IPv4 normally clears the ECN bits with IPTOS_RT_MASK before doing a FIB
lookup (although a few buggy code paths don't).
After this patch, IPv4 routes specifying an rtm_tos with any ECN bit
set is rejected.
Note: IPv6 routes ignore rtm_tos altogether, any rtm_tos is accepted,
but treated as if it were 0.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Define a dscp_t type and its appropriate helpers that ensure ECN bits
are not taken into account when handling DSCP.
Use this new type to replace the tclass field of struct fib6_rule, so
that fib6-rules don't get influenced by ECN bits anymore.
Before this patch, fib6-rules didn't make any distinction between the
DSCP and ECN bits. Therefore, rules specifying a DSCP (tos or dsfield
options in iproute2) stopped working as soon a packets had at least one
of its ECN bits set (as a work around one could create four rules for
each DSCP value to match, one for each possible ECN value).
After this patch fib6-rules only compare the DSCP bits. ECN doesn't
influence the result anymore. Also, fib6-rules now must have the ECN
bits cleared or they will be rejected.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While testing a patch that will follow later
("net: add netns refcount tracker to struct nsproxy")
I found that devtmpfs_init() was called before init_net
was initialized.
This is a bug, because devtmpfs_setup() calls
ksys_unshare(CLONE_NEWNS);
This has the effect of increasing init_net refcount,
which will be later overwritten to 1, as part of setup_net(&init_net)
We had too many prior patches [1] trying to work around the root cause.
Really, make sure init_net is in BSS section, and that net_ns_init()
is called earlier at boot time.
Note that another patch ("vfs: add netns refcount tracker
to struct fs_context") also will need net_ns_init() being called
before vfs_caches_init()
As a bonus, this patch saves around 4KB in .data section.
[1]
f8c46cb390 ("netns: do not call pernet ops for not yet set up init_net namespace")
b5082df801 ("net: Initialise init_net.count to 1")
734b65417b ("net: Statically initialize init_net.dev_base_head")
v2: fixed a build error reported by kernel build bots (CONFIG_NET=n)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While inspecting some perf report, I noticed that the compiler
emits suboptimal code for the napi CB initialization, fetching
and storing multiple times the memory for flags bitfield.
This is with gcc 10.3.1, but I observed the same with older compiler
versions.
We can help the compiler to do a nicer work clearing several
fields at once using an u32 alias. The generated code is quite
smaller, with the same number of conditional.
Before:
objdump -t net/core/gro.o | grep " F .text"
0000000000000bb0 l F .text 0000000000000357 dev_gro_receive
After:
0000000000000bb0 l F .text 000000000000033c dev_gro_receive
v1 -> v2:
- use struct_group (Alexander and Alex)
RFC -> v1:
- use __struct_group to delimit the zeroed area (Alexander)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tc skb extension is used to send miss info from
tc to ovs datapath module, and driver to tc. For the tc to ovs
miss it is currently always allocated even if it will not
be used by ovs datapath (as it depends on a requested feature).
Export the static key which is used by openvswitch module to
guard this code path as well, so it will be skipped if ovs
datapath doesn't need it. Enable this code path once
ovs datapath needs it.
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of the status_driver_data field was not adjusted when
the is_valid_ack_signal field was added.
Since the size of struct ieee80211_tx_info is limited, replace
the is_valid_ack_signal field with a flags field, and adjust the
struct size accordingly.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.0ff363d4fa56.I45792c0187034a6d0e1c99a7db741996ef7caba3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These no longer register/unregister a meaningful structure so remove it.
Cc: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The nat module already exposes a few functions to the conntrack core.
Move the nat extension destroy hook to it.
After this, no conntrack extension needs a destroy hook.
'struct nf_ct_ext_type' and the register/unregister api can be removed
in a followup patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
No need to specify this in the registration modules, we already
collect all sizes for build-time checks on the maximum combined size.
After this change, all extensions except nat have no meaningful content
in their nf_ct_ext_type struct definition.
Next patch handles nat, this will then allow to remove the dynamic
register api completely.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
All extensions except one need 8 byte alignment, so just make that the
default.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The previous commit d01ffb9eee ("ax25: add refcount in ax25_dev
to avoid UAF bugs") introduces refcount into ax25_dev, but there
are reference leak paths in ax25_ctl_ioctl(), ax25_fwd_ioctl(),
ax25_rt_add(), ax25_rt_del() and ax25_rt_opt().
This patch uses ax25_dev_put() and adjusts the position of
ax25_addr_ax25dev() to fix reference cout leaks of ax25_dev.
Fixes: d01ffb9eee ("ax25: add refcount in ax25_dev to avoid UAF bugs")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220203150811.42256-1-duoming@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Given that standalone ports are now configured to bypass the ATU and
forward all frames towards the upstream port, extend the ATU bypass to
multichip systems.
Load VID 0 (standalone) into the VTU with the policy bit set. Since
VID 4095 (bridged) is already loaded, we now know that all VIDs in use
are always available in all VTUs. Therefore, we can safely enable
802.1Q on DSA ports.
Setting the DSA ports' VTU policy to TRAP means that all incoming
frames on VID 0 will be classified as MGMT - as a result, the ATU is
bypassed on all subsequent switches.
With this isolation in place, we are able to support configurations
that are simultaneously very quirky and very useful. Quirky because it
involves looping cables between local switchports like in this
example:
CPU
| .------.
.---0---. | .----0----.
| sw0 | | | sw1 |
'-1-2-3-' | '-1-2-3-4-'
$ @ '---' $ @ % %
We have three physically looped pairs ($, @, and %).
This is very useful because it allows us to run the kernel's
kselftests for the bridge on mv88e6xxx hardware.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear MapDA on standalone ports to bypass any ATU lookup that might
point the packet in the wrong direction. This means that all packets
are flooded using the PVT config. So make sure that standalone ports
are only allowed to communicate with the local upstream port.
Here is a scenario in which this is needed:
CPU
| .----.
.---0---. | .--0--.
| sw0 | | | sw1 |
'-1-2-3-' | '-1-2-'
'---'
- sw0p1 and sw1p1 are bridged
- sw0p2 and sw1p2 are in standalone mode
- Learning must be enabled on sw0p3 in order for hardware forwarding
to work properly between bridged ports
1. A packet with SA :aa comes in on sw1p2
1a. Egresses sw1p0
1b. Ingresses sw0p3, ATU adds an entry for :aa towards port 3
1c. Egresses sw0p0
2. A packet with DA :aa comes in on sw0p2
2a. If an ATU lookup is done at this point, the packet will be
incorrectly forwarded towards sw0p3. With this change in place,
the ATU is bypassed and the packet is forwarded in accordance
with the PVT, which only contains the CPU port.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant to permit a driver to perform "fragmenting" of the
page from within the driver instead of the current model which requires
pre-partitioning the page. The main motivation behind this is to support
use cases where the page will be split up by the driver after DMA instead
of before.
With this change it becomes possible to start using page pool to replace
some of the existing use cases where multiple references were being used
for a single page, but the number needed was unknown as the size could be
dynamic.
For example, with this code it would be possible to do something like
the following to handle allocation:
page = page_pool_alloc_pages();
if (!page)
return NULL;
page_pool_fragment_page(page, DRIVER_PAGECNT_BIAS_MAX);
rx_buf->page = page;
rx_buf->pagecnt_bias = DRIVER_PAGECNT_BIAS_MAX;
Then we would process a received buffer by handling it with:
rx_buf->pagecnt_bias--;
Once the page has been fully consumed we could then flush the remaining
instances with:
if (page_pool_defrag_page(page, rx_buf->pagecnt_bias))
continue;
page_pool_put_defragged_page(pool, page -1, !!budget);
The general idea is that we want to have the ability to allocate a page
with excess fragment count and then trim off the unneeded fragments.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzkaller was able to trigger a deadlock for NTF_MANAGED entries [0]:
kworker/0:16/14617 is trying to acquire lock:
ffffffff8d4dd370 (&tbl->lock){++-.}-{2:2}, at: ___neigh_create+0x9e1/0x2990 net/core/neighbour.c:652
[...]
but task is already holding lock:
ffffffff8d4dd370 (&tbl->lock){++-.}-{2:2}, at: neigh_managed_work+0x35/0x250 net/core/neighbour.c:1572
The neighbor entry turned to NUD_FAILED state, where __neigh_event_send()
triggered an immediate probe as per commit cd28ca0a3d ("neigh: reduce
arp latency") via neigh_probe() given table lock was held.
One option to fix this situation is to defer the neigh_probe() back to
the neigh_timer_handler() similarly as pre cd28ca0a3d. For the case
of NTF_MANAGED, this deferral is acceptable given this only happens on
actual failure state and regular / expected state is NUD_VALID with the
entry already present.
The fix adds a parameter to __neigh_event_send() in order to communicate
whether immediate probe is allowed or disallowed. Existing call-sites
of neigh_event_send() default as-is to immediate probe. However, the
neigh_managed_work() disables it via use of neigh_event_send_probe().
[0] <TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_deadlock_bug kernel/locking/lockdep.c:2956 [inline]
check_deadlock kernel/locking/lockdep.c:2999 [inline]
validate_chain kernel/locking/lockdep.c:3788 [inline]
__lock_acquire.cold+0x149/0x3ab kernel/locking/lockdep.c:5027
lock_acquire kernel/locking/lockdep.c:5639 [inline]
lock_acquire+0x1ab/0x510 kernel/locking/lockdep.c:5604
__raw_write_lock_bh include/linux/rwlock_api_smp.h:202 [inline]
_raw_write_lock_bh+0x2f/0x40 kernel/locking/spinlock.c:334
___neigh_create+0x9e1/0x2990 net/core/neighbour.c:652
ip6_finish_output2+0x1070/0x14f0 net/ipv6/ip6_output.c:123
__ip6_finish_output net/ipv6/ip6_output.c:191 [inline]
__ip6_finish_output+0x61e/0xe90 net/ipv6/ip6_output.c:170
ip6_finish_output+0x32/0x200 net/ipv6/ip6_output.c:201
NF_HOOK_COND include/linux/netfilter.h:296 [inline]
ip6_output+0x1e4/0x530 net/ipv6/ip6_output.c:224
dst_output include/net/dst.h:451 [inline]
NF_HOOK include/linux/netfilter.h:307 [inline]
ndisc_send_skb+0xa99/0x17f0 net/ipv6/ndisc.c:508
ndisc_send_ns+0x3a9/0x840 net/ipv6/ndisc.c:650
ndisc_solicit+0x2cd/0x4f0 net/ipv6/ndisc.c:742
neigh_probe+0xc2/0x110 net/core/neighbour.c:1040
__neigh_event_send+0x37d/0x1570 net/core/neighbour.c:1201
neigh_event_send include/net/neighbour.h:470 [inline]
neigh_managed_work+0x162/0x250 net/core/neighbour.c:1574
process_one_work+0x9ac/0x1650 kernel/workqueue.c:2307
worker_thread+0x657/0x1110 kernel/workqueue.c:2454
kthread+0x2e9/0x3a0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
</TASK>
Fixes: 7482e3841d ("net, neigh: Add NTF_MANAGED flag for managed neighbor entries")
Reported-by: syzbot+5239d0e1778a500d477a@syzkaller.appspotmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Roopa Prabhu <roopa@nvidia.com>
Tested-by: syzbot+5239d0e1778a500d477a@syzkaller.appspotmail.com
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220201193942.5055-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When setting RTO through BPF program, some SYN ACK packets were unaffected
and continued to use TCP_TIMEOUT_INIT constant. This patch adds timeout
option to struct request_sock. Option is initialized with TCP_TIMEOUT_INIT
and is reassigned through BPF using tcp_timeout_init call. SYN ACK
retransmits now use newly added timeout option.
Signed-off-by: Akhmat Karakotov <hmukos@yandex-team.ru>
Acked-by: Martin KaFai Lau <kafai@fb.com>
v2:
- Add timeout option to struct request_sock. Do not call
tcp_timeout_init on every syn ack retransmit.
v3:
- Use unsigned long for min. Bound tcp_timeout_init to TCP_RTO_MAX.
v4:
- Refactor duplicate code by adding reqsk_timeout function.
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain drivers may need to send management traffic to the switch for
things like register access, FDB dump, etc, to accelerate what their
slow bus (SPI, I2C, MDIO) can already do.
Ethernet is faster (especially in bulk transactions) but is also more
unreliable, since the user may decide to bring the DSA master down (or
not bring it up), therefore severing the link between the host and the
attached switch.
Drivers needing Ethernet-based register access already should have
fallback logic to the slow bus if the Ethernet method fails, but that
fallback may be based on a timeout, and the I/O to the switch may slow
down to a halt if the master is down, because every Ethernet packet will
have to time out. The driver also doesn't have the option to turn off
Ethernet-based I/O momentarily, because it wouldn't know when to turn it
back on.
Which is where this change comes in. By tracking NETDEV_CHANGE,
NETDEV_UP and NETDEV_GOING_DOWN events on the DSA master, we should know
the exact interval of time during which this interface is reliably
available for traffic. Provide this information to switches so they can
use it as they wish.
An helper is added dsa_port_master_is_operational() to check if a master
port is operational.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Give this structure a header to better explain its content.
Signed-off-by: David Girault <david.girault@qorvo.com>
[miquel.raynal@bootlin.com: Isolate this change from a bigger commit and
reword the comment]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220201180956.93581-1-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Add the SO_TXREHASH socket option to control hash rethink behavior per socket.
When default mode is set, sockets disable rehash at initialization and use
sysctl option when entering listen state. setsockopt() overrides default
behavior.
Signed-off-by: Akhmat Karakotov <hmukos@yandex-team.ru>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a per ns sysctl that controls the txhash rethink behavior:
net.core.txrehash. When enabled, the same behavior is retained,
when disabled, rethink is not performed. Sysctl is enabled by default.
Signed-off-by: Akhmat Karakotov <hmukos@yandex-team.ru>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_idents_reserve is only used in net/ipv4/route.c. Make it static
and remove the export.
Signed-off-by: David Ahern <dsahern@kernel.org>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since v2.5.44 and addition of ip_options_fragment()
ip_options_build() does not render headers for fragments
directly. @is_frag is always 0.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add support for RTL8822C hci_ver 0x08
- Add support for RTL8852AE part 0bda:2852
- Fix WBS setting for Intel legacy ROM products
- Enable SCO over I2S ib mt7921s
- Increment management interface revision
-----BEGIN PGP SIGNATURE-----
iQJNBAABCAA3FiEE7E6oRXp8w05ovYr/9JCA4xAyCykFAmH0VmcZHGx1aXoudm9u
LmRlbnR6QGludGVsLmNvbQAKCRD0kIDjEDILKciID/98aC7pDP9XpIVPRKNuEeev
gukoNdcxmWo4IOMGJD7FzfEa5uHkhTWxgngohOJycT0ssTWShFnWezmyCgDaEvU6
s/swQrq+iGRXSDacuawh7lRrwNqJjl9AEw89asPzk9jFIETSfnGF0nqMinSayj5I
zUPjkkg2KgsBKON0o3+W0MTpBexg9tU2mVPMxpgkYjbTi08vP47sRW7R3O7Z2agB
EWf4+spZWjhPma2InrLj/+9h0jaU7y0p/9g5+Y5dpzAT0jXzYg2lDivSsjB6ry2R
CX726zxTzygY0wyKYrLxQE5xsK7DFe7zhnRIY18cJtmlPwZ8SSc9kkLZQ33qWIKp
Zo6ObumXxIqwOh6Yu13evQ12aZE3sMynhe+Se9QLwZ744EShkGEwFVd0XfkIQhe8
nI4x6ys0GDIV/dHHztbraz5QXgqML7TVzKymkdhfdncGSseLVTb0nm14kYNG+LYK
yokzGWm3SoC/YXfBMZmaTI+Ch8ZftvBoReIYx4FJQuI195W7E+NB7wrQ+oArblnt
Wy36Yj47TtZH4xSOlmZ/wNM/ry1q1QyRE3n32N0/mXc/8NgyPgWUbs/CSrUjBJmf
wU/POZSJvL2K/EDySAZJNhWfML3LTT+1ZCWzHckVNHzFb/Q2D6llgUfptMlxfjFU
m7s4R3xT3oAZgu1pocbHKw==
=/KS7
-----END PGP SIGNATURE-----
Merge tag 'for-net-next-2022-01-28' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Add support for RTL8822C hci_ver 0x08
- Add support for RTL8852AE part 0bda:2852
- Fix WBS setting for Intel legacy ROM products
- Enable SCO over I2S ib mt7921s
- Increment management interface revision
* tag 'for-net-next-2022-01-28' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next: (30 commits)
Bluetooth: Increment management interface revision
Bluetooth: hci_sync: Fix queuing commands when HCI_UNREGISTER is set
Bluetooth: hci_h5: Add power reset via gpio in h5_btrtl_open
Bluetooth: btrtl: Add support for RTL8822C hci_ver 0x08
Bluetooth: hci_event: Fix HCI_EV_VENDOR max_len
Bluetooth: hci_core: Rate limit the logging of invalid SCO handle
Bluetooth: hci_event: Ignore multiple conn complete events
Bluetooth: msft: fix null pointer deref on msft_monitor_device_evt
Bluetooth: btmtksdio: mask out interrupt status
Bluetooth: btmtksdio: run sleep mode by default
Bluetooth: btmtksdio: lower log level in btmtksdio_runtime_[resume|suspend]()
Bluetooth: mt7921s: fix btmtksdio_[drv|fw]_pmctrl()
Bluetooth: mt7921s: fix bus hang with wrong privilege
Bluetooth: btmtksdio: refactor btmtksdio_runtime_[suspend|resume]()
Bluetooth: mt7921s: fix firmware coredump retrieve
Bluetooth: hci_serdev: call init_rwsem() before p->open()
Bluetooth: Remove kernel-doc style comment block
Bluetooth: btusb: Whitespace fixes for btusb_setup_csr()
Bluetooth: btusb: Add one more Bluetooth part for the Realtek RTL8852AE
Bluetooth: btintel: Fix WBS setting for Intel legacy ROM products
...
====================
Link: https://lore.kernel.org/r/20220128205915.3995760-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If we dereference ax25_dev after we call kfree(ax25_dev) in
ax25_dev_device_down(), it will lead to concurrency UAF bugs.
There are eight syscall functions suffer from UAF bugs, include
ax25_bind(), ax25_release(), ax25_connect(), ax25_ioctl(),
ax25_getname(), ax25_sendmsg(), ax25_getsockopt() and
ax25_info_show().
One of the concurrency UAF can be shown as below:
(USE) | (FREE)
| ax25_device_event
| ax25_dev_device_down
ax25_bind | ...
... | kfree(ax25_dev)
ax25_fillin_cb() | ...
ax25_fillin_cb_from_dev() |
... |
The root cause of UAF bugs is that kfree(ax25_dev) in
ax25_dev_device_down() is not protected by any locks.
When ax25_dev, which there are still pointers point to,
is released, the concurrency UAF bug will happen.
This patch introduces refcount into ax25_dev in order to
guarantee that there are no pointers point to it when ax25_dev
is released.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not straightforward to the newcomer that a single skb can
currently be sent at a time and that the internal process is to stop the
queue when processing a frame before re-enabling it.
Make this clear by documenting the ieee802154_wake/stop_queue()
helpers.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220125122540.855604-4-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Inline a part of ipv6_fixup_options() to avoid extra overhead on
function call if opt is NULL.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Another preparation patch. inet_cork_full already contains a field for
iflow, so we can avoid passing a separate struct iflow6 into
__ip6_append_data() and ip6_make_skb(), and use the flow stored in
inet_cork_full. Make sure callers set cork->fl, i.e. we init it in
ip6_append_data() and before calling ip6_make_skb().
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ip_select_ident_segs() has been very conservative about using
the connected socket private generator only for packets with IP_DF
set, claiming it was needed for some VJ compression implementations.
As mentioned in this referenced document, this can be abused.
(Ref: Off-Path TCP Exploits of the Mixed IPID Assignment)
Before switching to pure random IPID generation and possibly hurt
some workloads, lets use the private inet socket generator.
Not only this will remove one vulnerability, this will also
improve performance of TCP flows using pmtudisc==IP_PMTUDISC_DONT
Fixes: 73f156a6e8 ("inetpeer: get rid of ip_id_count")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reported-by: Ray Che <xijiache@gmail.com>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move desc_array from the driver to the pool. The reason behind this is
that we can then reuse this array as a temporary storage for descriptors
in all zero-copy drivers that use the batched interface. This will make
it easier to add batching to more drivers.
i40e is the only driver that has a batched Tx zero-copy
implementation, so no need to touch any other driver.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20220125160446.78976-6-maciej.fijalkowski@intel.com
This reverts commit b75326c201.
This commit breaks Linux compatibility with USGv6 tests. The RFC this
commit was based on is actually an expired draft: no published RFC
currently allows the new behaviour it introduced.
Without full IETF endorsement, the flash renumbering scenario this
patch was supposed to enable is never going to work, as other IPv6
equipements on the same LAN will keep the 2 hours limit.
Fixes: b75326c201 ("ipv6: Honor all IPv6 PIO Valid Lifetime values")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different netns has different requirement on the setting of min_adv_mss
sysctl which the advertised MSS will be never lower than.
Enable min_adv_mss to be configured per network namespace.
Signed-off-by: xu xin <xu.xin16@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit b515d26372.
Commit b515d26372 ("xfrm: xfrm_state_mtu
should return at least 1280 for ipv6") in v5.14 breaks the TCP MSS
calculation in ipsec transport mode, resulting complete stalls of TCP
connections. This happens when the (P)MTU is 1280 or slighly larger.
The desired formula for the MSS is:
MSS = (MTU - ESP_overhead) - IP header - TCP header
However, the above commit clamps the (MTU - ESP_overhead) to a
minimum of 1280, turning the formula into
MSS = max(MTU - ESP overhead, 1280) - IP header - TCP header
With the (P)MTU near 1280, the calculated MSS is too large and the
resulting TCP packets never make it to the destination because they
are over the actual PMTU.
The above commit also causes suboptimal double fragmentation in
xfrm tunnel mode, as described in
https://lore.kernel.org/netdev/20210429202529.codhwpc7w6kbudug@dwarf.suse.cz/
The original problem the above commit was trying to fix is now fixed
by commit 6596a02295 ("xfrm: fix MTU
regression").
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch enables distinguishing SAs and SPs based on if_id during
the xfrm_migrate flow. This ensures support for xfrm interfaces
throughout the SA/SP lifecycle.
When there are multiple existing SPs with the same direction,
the same xfrm_selector and different endpoint addresses,
xfrm_migrate might fail with ENODATA.
Specifically, the code path for performing xfrm_migrate is:
Stage 1: find policy to migrate with
xfrm_migrate_policy_find(sel, dir, type, net)
Stage 2: find and update state(s) with
xfrm_migrate_state_find(mp, net)
Stage 3: update endpoint address(es) of template(s) with
xfrm_policy_migrate(pol, m, num_migrate)
Currently "Stage 1" always returns the first xfrm_policy that
matches, and "Stage 3" looks for the xfrm_tmpl that matches the
old endpoint address. Thus if there are multiple xfrm_policy
with same selector, direction, type and net, "Stage 1" might
rertun a wrong xfrm_policy and "Stage 3" will fail with ENODATA
because it cannot find a xfrm_tmpl with the matching endpoint
address.
The fix is to allow userspace to pass an if_id and add if_id
to the matching rule in Stage 1 and Stage 2 since if_id is a
unique ID for xfrm_policy and xfrm_state. For compatibility,
if_id will only be checked if the attribute is set.
Tested with additions to Android's kernel unit test suite:
https://android-review.googlesource.com/c/kernel/tests/+/1668886
Signed-off-by: Yan Yan <evitayan@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
TCP ipv4 uses per-cpu/per-netns ctl sockets in order to send
RST and some ACK packets (on behalf of TIMEWAIT sockets).
This adds memory and cpu costs, which do not seem needed.
Now typical servers have 256 or more cores, this adds considerable
tax to netns users.
tcp sockets are used from BH context, are not receiving packets,
and do not store any persistent state but the 'struct net' pointer
in order to be able to use IPv4 output functions.
Note that I attempted a related change in the past, that had
to be hot-fixed in commit bdbbb8527b ("ipv4: tcp: get rid of ugly unicast_sock")
This patch could very well surface old bugs, on layers not
taking care of sk->sk_kern_sock properly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in linux-2.6.25 (commit 98c6d1b261 "[NETNS]: Make icmpv6_sk per namespace.",
we added private per-cpu/per-netns ipv6 icmp sockets.
This adds memory and cpu costs, which do not seem needed.
Now typical servers have 256 or more cores, this adds considerable
tax to netns users.
icmp sockets are used from BH context, are not receiving packets,
and do not store any persistent state but the 'struct net' pointer.
icmpv6_xmit_lock() already makes sure to lock the chosen per-cpu
socket.
This patch has a considerable impact on the number of netns
that the worker thread in cleanup_net() can dismantle per second,
because ip6mr_sk_done() is no longer called, meaning we no longer
acquire the rtnl mutex, competing with other threads adding new netns.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in linux-2.6.25 (commit 4a6ad7a141 "[NETNS]: Make icmp_sk per namespace."),
we added private per-cpu/per-netns ipv4 icmp sockets.
This adds memory and cpu costs, which do not seem needed.
Now typical servers have 256 or more cores, this adds considerable
tax to netns users.
icmp sockets are used from BH context, are not receiving packets,
and do not store any persistent state but the 'struct net' pointer.
icmp_xmit_lock() already makes sure to lock the chosen per-cpu
socket.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior patches in the series made sure tw_timer_handler()
can be fired after netns has been dismantled/freed.
We no longer have to scan a potentially big TCP ehash
table at netns dismantle.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon get rid of inet_twsk_purge().
This means that tw_timer_handler() might fire after
a netns has been dismantled/freed.
Instead of adding a function (and data structure) to find a netns
from tw->tw_net_cookie, just update the SNMP counters
a bit earlier, when the netns is known to be alive.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to allow inet_twsk_kill() working even if netns
has been dismantled/freed, to get rid of inet_twsk_purge().
This patch adds tw->tw_bslot to cache the bind bucket slot
so that inet_twsk_kill() no longer needs to dereference twsk_net(tw)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When one of the three connection complete events is received multiple
times for the same handle, the device is registered multiple times which
leads to memory corruptions. Therefore, consequent events for a single
connection are ignored.
The conn->state can hold different values, therefore HCI_CONN_HANDLE_UNSET
is introduced to identify new connections. To make sure the events do not
contain this or another invalid handle HCI_CONN_HANDLE_MAX and checks
are introduced.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=215497
Signed-off-by: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2022-01-24
We've added 80 non-merge commits during the last 14 day(s) which contain
a total of 128 files changed, 4990 insertions(+), 895 deletions(-).
The main changes are:
1) Add XDP multi-buffer support and implement it for the mvneta driver,
from Lorenzo Bianconi, Eelco Chaudron and Toke Høiland-Jørgensen.
2) Add unstable conntrack lookup helpers for BPF by using the BPF kfunc
infra, from Kumar Kartikeya Dwivedi.
3) Extend BPF cgroup programs to export custom ret value to userspace via
two helpers bpf_get_retval() and bpf_set_retval(), from YiFei Zhu.
4) Add support for AF_UNIX iterator batching, from Kuniyuki Iwashima.
5) Complete missing UAPI BPF helper description and change bpf_doc.py script
to enforce consistent & complete helper documentation, from Usama Arif.
6) Deprecate libbpf's legacy BPF map definitions and streamline XDP APIs to
follow tc-based APIs, from Andrii Nakryiko.
7) Support BPF_PROG_QUERY for BPF programs attached to sockmap, from Di Zhu.
8) Deprecate libbpf's bpf_map__def() API and replace users with proper getters
and setters, from Christy Lee.
9) Extend libbpf's btf__add_btf() with an additional hashmap for strings to
reduce overhead, from Kui-Feng Lee.
10) Fix bpftool and libbpf error handling related to libbpf's hashmap__new()
utility function, from Mauricio Vásquez.
11) Add support to BTF program names in bpftool's program dump, from Raman Shukhau.
12) Fix resolve_btfids build to pick up host flags, from Connor O'Brien.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (80 commits)
selftests, bpf: Do not yet switch to new libbpf XDP APIs
selftests, xsk: Fix rx_full stats test
bpf: Fix flexible_array.cocci warnings
xdp: disable XDP_REDIRECT for xdp frags
bpf: selftests: add CPUMAP/DEVMAP selftests for xdp frags
bpf: selftests: introduce bpf_xdp_{load,store}_bytes selftest
net: xdp: introduce bpf_xdp_pointer utility routine
bpf: generalise tail call map compatibility check
libbpf: Add SEC name for xdp frags programs
bpf: selftests: update xdp_adjust_tail selftest to include xdp frags
bpf: test_run: add xdp_shared_info pointer in bpf_test_finish signature
bpf: introduce frags support to bpf_prog_test_run_xdp()
bpf: move user_size out of bpf_test_init
bpf: add frags support to xdp copy helpers
bpf: add frags support to the bpf_xdp_adjust_tail() API
bpf: introduce bpf_xdp_get_buff_len helper
net: mvneta: enable jumbo frames if the loaded XDP program support frags
bpf: introduce BPF_F_XDP_HAS_FRAGS flag in prog_flags loading the ebpf program
net: mvneta: add frags support to XDP_TX
xdp: add frags support to xdp_return_{buff/frame}
...
====================
Link: https://lore.kernel.org/r/20220124221235.18993-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bond_option_active_slave_get_rcu() should not be used in rtnl_mutex as it
use rcu_dereference(). Replace to rcu_dereference_rtnl() so we also can use
this function in rtnl protected context.
With this update, we can rmeove the rcu_read_lock/unlock in
bonding .ndo_eth_ioctl and .get_ts_info.
Reported-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Fixes: 94dd016ae5 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP ioctl to active device")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds support for tail growing and shrinking for XDP frags.
When called on a non-linear packet with a grow request, it will work
on the last fragment of the packet. So the maximum grow size is the
last fragments tailroom, i.e. no new buffer will be allocated.
A XDP frags capable driver is expected to set frag_size in xdp_rxq_info
data structure to notify the XDP core the fragment size.
frag_size set to 0 is interpreted by the XDP core as tail growing is
not allowed.
Introduce __xdp_rxq_info_reg utility routine to initialize frag_size field.
When shrinking, it will work from the last fragment, all the way down to
the base buffer depending on the shrinking size. It's important to mention
that once you shrink down the fragment(s) are freed, so you can not grow
again to the original size.
Acked-by: Toke Hoiland-Jorgensen <toke@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/eabda3485dda4f2f158b477729337327e609461d.1642758637.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Introduce bpf_xdp_get_buff_len helper in order to return the xdp buffer
total size (linear and paged area)
Acked-by: Toke Hoiland-Jorgensen <toke@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/aac9ac3504c84026cf66a3c71b7c5ae89bc991be.1642758637.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Take into account if the received xdp_buff/xdp_frame is non-linear
recycling/returning the frame memory to the allocator or into
xdp_frame_bulk.
Acked-by: Toke Hoiland-Jorgensen <toke@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/a961069febc868508ce1bdf5e53a343eb4e57cb2.1642758637.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Introduce xdp_update_skb_shared_info routine to update frags array
metadata in skb_shared_info data structure converting to a skb from
a xdp_buff or xdp_frame.
According to the current skb_shared_info architecture in
xdp_frame/xdp_buff and to the xdp frags support, there is
no need to run skb_add_rx_frag() and reset frags array converting the buffer
to a skb since the frag array will be in the same position for xdp_buff/xdp_frame
and for the skb, we just need to update memory metadata.
Introduce XDP_FLAGS_PF_MEMALLOC flag in xdp_buff_flags in order to mark
the xdp_buff or xdp_frame as under memory-pressure if pages of the frags array
are under memory pressure. Doing so we can avoid looping over all fragments in
xdp_update_skb_shared_info routine. The driver is expected to set the
flag constructing the xdp_buffer using xdp_buff_set_frag_pfmemalloc
utility routine.
Rely on xdp_update_skb_shared_info in __xdp_build_skb_from_frame routine
converting the non-linear xdp_frame to a skb after performing a XDP_REDIRECT.
Acked-by: Toke Hoiland-Jorgensen <toke@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/bfd23fb8a8d7438724f7819c567cdf99ffd6226f.1642758637.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Introduce flags field in xdp_frame and xdp_buffer data structures
to define additional buffer features. At the moment the only
supported buffer feature is frags bit (XDP_FLAGS_HAS_FRAGS).
frags bit is used to specify if this is a linear buffer
(XDP_FLAGS_HAS_FRAGS not set) or a frags frame (XDP_FLAGS_HAS_FRAGS
set). In the latter case the driver is expected to initialize the
skb_shared_info structure at the end of the first buffer to link together
subsequent buffers belonging to the same frame.
Acked-by: Toke Hoiland-Jorgensen <toke@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/e389f14f3a162c0a5bc6a2e1aa8dd01a90be117d.1642758637.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When compiling the kernel with CONFIG_INET disabled, the
sk_defer_free_flush() should be defined as a nop.
This resolves the following compilation error:
ld: net/core/sock.o: in function `sk_defer_free_flush':
./include/net/tcp.h:1378: undefined reference to `__sk_defer_free_flush'
Fixes: 79074a72d3 ("net: Flush deferred skb free on socket destroy")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220120123440.9088-1-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch introduces two new MGMT events for notifying the bluetoothd
whenever the controller starts/stops monitoring a device.
Test performed:
- Verified by logs that the MSFT Monitor Device is received from the
controller and the bluetoothd is notified whenever the controller
starts/stops monitoring a device.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Miao-chen Chou <mcchou@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Whenever the controller starts/stops monitoring a bt device, it sends
MSFT Monitor Device event. Add handler to read this vendor event.
Test performed:
- Verified by logs that the MSFT Monitor Device event is received from
the controller whenever it starts/stops monitoring a device.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Miao-chen Chou <mcchou@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Current release - regressions:
- fix memory leaks in the skb free deferral scheme if upper layer
protocols are used, i.e. in-kernel TCP readers like TLS
Current release - new code bugs:
- nf_tables: fix NULL check typo in _clone() functions
- change the default to y for Vertexcom vendor Kconfig
- a couple of fixes to incorrect uses of ref tracking
- two fixes for constifying netdev->dev_addr
Previous releases - regressions:
- bpf:
- various verifier fixes mainly around register offset handling
when passed to helper functions
- fix mount source displayed for bpffs (none -> bpffs)
- bonding:
- fix extraction of ports for connection hash calculation
- fix bond_xmit_broadcast return value when some devices are down
- phy: marvell: add Marvell specific PHY loopback
- sch_api: don't skip qdisc attach on ingress, prevent ref leak
- htb: restore minimal packet size handling in rate control
- sfp: fix high power modules without diagnostic monitoring
- mscc: ocelot:
- don't let phylink re-enable TX PAUSE on the NPI port
- don't dereference NULL pointers with shared tc filters
- smsc95xx: correct reset handling for LAN9514
- cpsw: avoid alignment faults by taking NET_IP_ALIGN into account
- phy: micrel: use kszphy_suspend/_resume for irq aware devices,
avoid races with the interrupt
Previous releases - always broken:
- xdp: check prog type before updating BPF link
- smc: resolve various races around abnormal connection termination
- sit: allow encapsulated IPv6 traffic to be delivered locally
- axienet: fix init/reset handling, add missing barriers,
read the right status words, stop queues correctly
- add missing dev_put() in sock_timestamping_bind_phc()
Misc:
- ipv4: prevent accidentally passing RTO_ONLINK to
ip_route_output_key_hash() by sanitizing flags
- ipv4: avoid quadratic behavior in netns dismantle
- stmmac: dwmac-oxnas: add support for OX810SE
- fsl: xgmac_mdio: add workaround for erratum A-009885
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=XM4Y
-----END PGP SIGNATURE-----
Merge tag 'net-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, bpf.
Quite a handful of old regression fixes but most of those are
pre-5.16.
Current release - regressions:
- fix memory leaks in the skb free deferral scheme if upper layer
protocols are used, i.e. in-kernel TCP readers like TLS
Current release - new code bugs:
- nf_tables: fix NULL check typo in _clone() functions
- change the default to y for Vertexcom vendor Kconfig
- a couple of fixes to incorrect uses of ref tracking
- two fixes for constifying netdev->dev_addr
Previous releases - regressions:
- bpf:
- various verifier fixes mainly around register offset handling
when passed to helper functions
- fix mount source displayed for bpffs (none -> bpffs)
- bonding:
- fix extraction of ports for connection hash calculation
- fix bond_xmit_broadcast return value when some devices are down
- phy: marvell: add Marvell specific PHY loopback
- sch_api: don't skip qdisc attach on ingress, prevent ref leak
- htb: restore minimal packet size handling in rate control
- sfp: fix high power modules without diagnostic monitoring
- mscc: ocelot:
- don't let phylink re-enable TX PAUSE on the NPI port
- don't dereference NULL pointers with shared tc filters
- smsc95xx: correct reset handling for LAN9514
- cpsw: avoid alignment faults by taking NET_IP_ALIGN into account
- phy: micrel: use kszphy_suspend/_resume for irq aware devices,
avoid races with the interrupt
Previous releases - always broken:
- xdp: check prog type before updating BPF link
- smc: resolve various races around abnormal connection termination
- sit: allow encapsulated IPv6 traffic to be delivered locally
- axienet: fix init/reset handling, add missing barriers, read the
right status words, stop queues correctly
- add missing dev_put() in sock_timestamping_bind_phc()
Misc:
- ipv4: prevent accidentally passing RTO_ONLINK to
ip_route_output_key_hash() by sanitizing flags
- ipv4: avoid quadratic behavior in netns dismantle
- stmmac: dwmac-oxnas: add support for OX810SE
- fsl: xgmac_mdio: add workaround for erratum A-009885"
* tag 'net-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (92 commits)
ipv4: add net_hash_mix() dispersion to fib_info_laddrhash keys
ipv4: avoid quadratic behavior in netns dismantle
net/fsl: xgmac_mdio: Fix incorrect iounmap when removing module
powerpc/fsl/dts: Enable WA for erratum A-009885 on fman3l MDIO buses
dt-bindings: net: Document fsl,erratum-a009885
net/fsl: xgmac_mdio: Add workaround for erratum A-009885
net: mscc: ocelot: fix using match before it is set
net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices
net: cpsw: avoid alignment faults by taking NET_IP_ALIGN into account
nfc: llcp: fix NULL error pointer dereference on sendmsg() after failed bind()
net: axienet: increase default TX ring size to 128
net: axienet: fix for TX busy handling
net: axienet: fix number of TX ring slots for available check
net: axienet: Fix TX ring slot available check
net: axienet: limit minimum TX ring size
net: axienet: add missing memory barriers
net: axienet: reset core on initialization prior to MDIO access
net: axienet: Wait for PhyRstCmplt after core reset
net: axienet: increase reset timeout
bpf, selftests: Add ringbuf memory type confusion test
...
This change adds conntrack lookup helpers using the unstable kfunc call
interface for the XDP and TC-BPF hooks. The primary usecase is
implementing a synproxy in XDP, see Maxim's patchset [0].
Export get_net_ns_by_id as nf_conntrack_bpf.c needs to call it.
This object is only built when CONFIG_DEBUG_INFO_BTF_MODULES is enabled.
[0]: https://lore.kernel.org/bpf/20211019144655.3483197-1-maximmi@nvidia.com
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20220114163953.1455836-7-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
- fix possible uninitialized memory usage for setattr
- fix fscache reading hole in a file just after it's been grown
- split net/9p/trans_fd.c in its own module like other transports
that module defaults to 9P_NET and is autoloaded if required so
users should not be impacted
- add Christian Schoenebeck to 9p reviewers
- some more trivial cleanup
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE/IPbcYBuWt0zoYhOq06b7GqY5nAFAmHgt18ACgkQq06b7GqY
5nAdUA//ZHFTIcnbTiVkqbw0YztxedTOhdGCWcYsszux0pNQ/ZCjbP5NxESWiFxs
raYWcvE98Xvq4fbs8b+m7YKBJzWF+Km/v1MKfgvZZWFLZR3MfWiL8iojlsaUgG9U
rBmEUyaTWw2COIvFN7EqnwT5mwzNCli5d3AzaAmgffWsHEi/+EVU35YX70ySUkjW
nVf08oX3dBB425oArXOZApOZSVRsUr5YDSuQGiFHBL+hvPTrvPumu/AXbjLbTbmf
NuUxu1Akw8/jhWNATLHzjCdzJzBSfF0zRs+oH9Qt8MKkUrlTfjxc/2MbQYL1p1IN
84XxiG02ebw+Mx05cydP9/Ll7gOo2p6ORGXMHcoPIAMy6zFiCKo3TRdKDgmYDauC
K8c3v+osNwl2GFn1+2XoQIWnqXb7bJ1debkFtWVEGOPd/Yr6CYCZyfiZamoPJXUO
TjkoLAJXJGKlV66ZCuVeAsySdUxdtwbj2WxTliDUWtxvQ+m1jt06S3f/TbA7a9bB
8aBhx7FKzQ/UL8zhm4+3WLPlWkoSUXhFSZZUknvhuaHFV/S1xglXox5OAQJrJMy+
qOzmOjCg14T1TC2WkJlEsedLUH8ACU+XueAPT6uqSdA4rvQEVzk32zTm/GfFu3Q3
0RhcGlW5kAAYBTBLXvmKsjyW2OmPCSycgbWCu3E8A/1gubbRE40=
=o2Lc
-----END PGP SIGNATURE-----
Merge tag '9p-for-5.17-rc1' of git://github.com/martinetd/linux
Pull 9p updates from Dominique Martinet:
"Fixes, split 9p_net_fd, and new reviewer:
- fix possible uninitialized memory usage for setattr
- fix fscache reading hole in a file just after it's been grown
- split net/9p/trans_fd.c in its own module like other transports.
The new transport module defaults to 9P_NET and is autoloaded if
required so users should not be impacted
- add Christian Schoenebeck to 9p reviewers
- some more trivial cleanup"
* tag '9p-for-5.17-rc1' of git://github.com/martinetd/linux:
9p: fix enodata when reading growing file
net/9p: show error message if user 'msize' cannot be satisfied
MAINTAINERS: 9p: add Christian Schoenebeck as reviewer
9p: only copy valid iattrs in 9P2000.L setattr implementation
9p: Use BUG_ON instead of if condition followed by BUG.
net/p9: load default transports
9p/xen: autoload when xenbus service is available
9p/trans_fd: split into dedicated module
fs: 9p: remove unneeded variable
9p/trans_virtio: Fix typo in the comment for p9_virtio_create()
commit 56b765b79e ("htb: improved accuracy at high rates") broke
"overhead X", "linklayer atm" and "mpu X" attributes.
"overhead X" and "linklayer atm" have already been fixed. This restores
the "mpu X" handling, as might be used by DOCSIS or Ethernet shaping:
tc class add ... htb rate X overhead 4 mpu 64
The code being fixed is used by htb, tbf and act_police. Cake has its
own mpu handling. qdisc_calculate_pkt_len still uses the size table
containing values adjusted for mpu by user space.
iproute2 tc has always passed mpu into the kernel via a tc_ratespec
structure, but the kernel never directly acted on it, merely stored it
so that it could be read back by `tc class show`.
Rather, tc would generate length-to-time tables that included the mpu
(and linklayer) in their construction, and the kernel used those tables.
Since v3.7, the tables were no longer used. Along with "mpu", this also
broke "overhead" and "linklayer" which were fixed in 01cb71d2d4
("net_sched: restore "overhead xxx" handling", v3.10) and 8a8e3d84b1
("net_sched: restore "linklayer atm" handling", v3.11).
"overhead" was fixed by simply restoring use of tc_ratespec::overhead -
this had originally been used by the kernel but was initially omitted
from the new non-table-based calculations.
"linklayer" had been handled in the table like "mpu", but the mode was
not originally passed in tc_ratespec. The new implementation was made to
handle it by getting new versions of tc to pass the mode in an extended
tc_ratespec, and for older versions of tc the table contents were analysed
at load time to deduce linklayer.
As "mpu" has always been given to the kernel in tc_ratespec,
accompanying the mpu-based table, we can restore system functionality
with no userspace change by making the kernel act on the tc_ratespec
value.
Fixes: 56b765b79e ("htb: improved accuracy at high rates")
Signed-off-by: Kevin Bracey <kevin@bracey.fi>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Vimalkumar <j.vimal@gmail.com>
Link: https://lore.kernel.org/r/20220112170210.1014351-1-kevin@bracey.fi
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Both fields can be read/written without synchronization,
add proper accessors and documentation.
Fixes: d5dd88794a ("inet: fix various use-after-free in defrags units")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While struct tcf_exts has a net pointer, it is not refcounted
until tcf_exts_get_net() is called.
Fixes: dbdcda634c ("net: sched: add netns refcount tracker to struct tcf_exts")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220110094750.236478-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that all transports are split into modules it may happen that no
transports are registered when v9fs_get_default_trans() is called.
When that is the case try to load more transports from modules.
Link: https://lkml.kernel.org/r/20211103193823.111007-5-linux@weissschuh.net
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
[Dominique: constify v9fs_get_trans_by_name argument as per patch1v2]
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
This allows these transports only to be used when needed.
Link: https://lkml.kernel.org/r/20211103193823.111007-3-linux@weissschuh.net
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
[Dominique: Kconfig NET_9P_FD: -depends VIRTIO, +default NET_9P]
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Netfilter conntrack maintains NAT flags per connection indicating
whether NAT was configured for the connection. Openvswitch maintains
NAT flags on the per packet flow key ct_state field, indicating
whether NAT was actually executed on the packet.
When a packet misses from tc to ovs the conntrack NAT flags are set.
However, NAT was not necessarily executed on the packet because the
connection's state might still be in NEW state. As such, openvswitch
wrongly assumes that NAT was executed and sets an incorrect flow key
NAT flags.
Fix this, by flagging to openvswitch which NAT was actually done in
act_ct via tc_skb_ext and tc_skb_cb to the openvswitch module, so
the packet flow key NAT flags will be correctly set.
Fixes: b57dc7c13e ("net/sched: Introduce action ct")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20220106153804.26451-1-paulb@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next. This
includes one patch to update ovs and act_ct to use nf_ct_put() instead
of nf_conntrack_put().
1) Add netns_tracker to nfnetlink_log and masquerade, from Eric Dumazet.
2) Remove redundant rcu read-size lock in nf_tables packet path.
3) Replace BUG() by WARN_ON_ONCE() in nft_payload.
4) Consolidate rule verdict tracing.
5) Replace WARN_ON() by WARN_ON_ONCE() in nf_tables core.
6) Make counter support built-in in nf_tables.
7) Add new field to conntrack object to identify locally generated
traffic, from Florian Westphal.
8) Prevent NAT from shadowing well-known ports, from Florian Westphal.
9) Merge nf_flow_table_{ipv4,ipv6} into nf_flow_table_inet, also from
Florian.
10) Remove redundant pointer in nft_pipapo AVX2 support, from Colin Ian King.
11) Replace opencoded max() in conntrack, from Jiapeng Chong.
12) Update conntrack to use refcount_t API, from Florian Westphal.
13) Move ip_ct_attach indirection into the nf_ct_hook structure.
14) Constify several pointer object in the netfilter codebase,
from Florian Westphal.
15) Tree-wide replacement of nf_conntrack_put() by nf_ct_put(), also
from Florian.
16) Fix egress splat due to incorrect rcu notation, from Florian.
17) Move stateful fields of connlimit, last, quota, numgen and limit
out of the expression data area.
18) Build a blob to represent the ruleset in nf_tables, this is a
requirement of the new register tracking infrastructure.
19) Add NFT_REG32_NUM to define the maximum number of 32-bit registers.
20) Add register tracking infrastructure to skip redundant
store-to-register operations, this includes support for payload,
meta and bitwise expresssions.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next: (32 commits)
netfilter: nft_meta: cancel register tracking after meta update
netfilter: nft_payload: cancel register tracking after payload update
netfilter: nft_bitwise: track register operations
netfilter: nft_meta: track register operations
netfilter: nft_payload: track register operations
netfilter: nf_tables: add register tracking infrastructure
netfilter: nf_tables: add NFT_REG32_NUM
netfilter: nf_tables: add rule blob layout
netfilter: nft_limit: move stateful fields out of expression data
netfilter: nft_limit: rename stateful structure
netfilter: nft_numgen: move stateful fields out of expression data
netfilter: nft_quota: move stateful fields out of expression data
netfilter: nft_last: move stateful fields out of expression data
netfilter: nft_connlimit: move stateful fields out of expression data
netfilter: egress: avoid a lockdep splat
net: prefer nf_ct_put instead of nf_conntrack_put
netfilter: conntrack: avoid useless indirection during conntrack destruction
netfilter: make function op structures const
netfilter: core: move ip_ct_attach indirection to struct nf_ct_hook
netfilter: conntrack: convert to refcount_t api
...
====================
Link: https://lore.kernel.org/r/20220109231640.104123-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Check if the destination register already contains the data that this
bitwise expression performs. This allows to skip this redundant
operation.
If the destination contains a different bitwise operation, cancel the
register tracking information. If the destination contains no bitwise
operation, update the register tracking information.
Update the payload and meta expression to check if this bitwise
operation has been already performed on the register. Hence, both the
payload/meta and the bitwise expressions are reduced.
There is also a special case: If source register != destination register
and source register is not updated by a previous bitwise operation, then
transfer selector from the source register to the destination register.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds new infrastructure to skip redundant selector store
operations on the same register to achieve a performance boost from
the packet path.
This is particularly noticeable in pure linear rulesets but it also
helps in rulesets which are already heaving relying in maps to avoid
ruleset linear inspection.
The idea is to keep data of the most recurrent store operations on
register to reuse them with cmp and lookup expressions.
This infrastructure allows for dynamic ruleset updates since the ruleset
blob reduction happens from the kernel.
Userspace still needs to be updated to maximize register utilization to
cooperate to improve register data reuse / reduce number of store on
register operations.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add a definition including the maximum number of 32-bits registers that
are used a scratchpad memory area to store data.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds a blob layout per chain to represent the ruleset in the
packet datapath.
size (unsigned long)
struct nft_rule_dp
struct nft_expr
...
struct nft_rule_dp
struct nft_expr
...
struct nft_rule_dp (is_last=1)
The new structure nft_rule_dp represents the rule in a more compact way
(smaller memory footprint) compared to the control-plane nft_rule
structure.
The ruleset blob is a read-only data structure. The first field contains
the blob size, then the rules containing expressions. There is a trailing
rule which is used by the tracing infrastructure which is equivalent to
the NULL rule marker in the previous representation. The blob size field
does not include the size of this trailing rule marker.
The ruleset blob is generated from the commit path.
This patch reuses the infrastructure available since 0cbc06b3fa
("netfilter: nf_tables: remove synchronize_rcu in commit phase") to
build the array of rules per chain.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_ct_put() results in a usesless indirection:
nf_ct_put -> nf_conntrack_put -> nf_conntrack_destroy -> rcu readlock +
indirect call of ct_hooks->destroy().
There are two _put helpers:
nf_ct_put and nf_conntrack_put. The latter is what should be used in
code that MUST NOT cause a linker dependency on the conntrack module
(e.g. calls from core network stack).
Everyone else should call nf_ct_put() instead.
A followup patch will convert a few nf_conntrack_put() calls to
nf_ct_put(), in particular from modules that already have a conntrack
dependency such as act_ct or even nf_conntrack itself.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
- Add support for Foxconn QCA 0xe0d0
- Fix HCI init sequence on MacBook Air 8,1 and 8,2
- Fix Intel firmware loading on legacy ROM devices
-----BEGIN PGP SIGNATURE-----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=q2FV
-----END PGP SIGNATURE-----
Merge tag 'for-net-next-2022-01-07' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Add support for Foxconn QCA 0xe0d0
- Fix HCI init sequence on MacBook Air 8,1 and 8,2
- Fix Intel firmware loading on legacy ROM devices
* tag 'for-net-next-2022-01-07' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next:
Bluetooth: hci_sock: fix endian bug in hci_sock_setsockopt()
Bluetooth: L2CAP: uninitialized variables in l2cap_sock_setsockopt()
Bluetooth: btqca: sequential validation
Bluetooth: btusb: Add support for Foxconn QCA 0xe0d0
Bluetooth: btintel: Fix broken LED quirk for legacy ROM devices
Bluetooth: hci_event: Rework hci_inquiry_result_with_rssi_evt
Bluetooth: btbcm: disable read tx power for MacBook Air 8,1 and 8,2
Bluetooth: hci_qca: Fix NULL vs IS_ERR_OR_NULL check in qca_serdev_probe
Bluetooth: hci_bcm: Check for error irq
====================
Link: https://lore.kernel.org/r/20220107210942.3750887-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2022-01-06
We've added 41 non-merge commits during the last 2 day(s) which contain
a total of 36 files changed, 1214 insertions(+), 368 deletions(-).
The main changes are:
1) Various fixes in the verifier, from Kris and Daniel.
2) Fixes in sockmap, from John.
3) bpf_getsockopt fix, from Kuniyuki.
4) INET_POST_BIND fix, from Menglong.
5) arm64 JIT fix for bpf pseudo funcs, from Hou.
6) BPF ISA doc improvements, from Christoph.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (41 commits)
bpf: selftests: Add bind retry for post_bind{4, 6}
bpf: selftests: Use C99 initializers in test_sock.c
net: bpf: Handle return value of BPF_CGROUP_RUN_PROG_INET{4,6}_POST_BIND()
bpf/selftests: Test bpf_d_path on rdonly_mem.
libbpf: Add documentation for bpf_map batch operations
selftests/bpf: Don't rely on preserving volatile in PT_REGS macros in loop3
xdp: Add xdp_do_redirect_frame() for pre-computed xdp_frames
xdp: Move conversion to xdp_frame out of map functions
page_pool: Store the XDP mem id
page_pool: Add callback to init pages when they are allocated
xdp: Allow registering memory model without rxq reference
samples/bpf: xdpsock: Add timestamp for Tx-only operation
samples/bpf: xdpsock: Add time-out for cleaning Tx
samples/bpf: xdpsock: Add sched policy and priority support
samples/bpf: xdpsock: Add cyclic TX operation capability
samples/bpf: xdpsock: Add clockid selection support
samples/bpf: xdpsock: Add Dest and Src MAC setting for Tx-only operation
samples/bpf: xdpsock: Add VLAN support for Tx-only operation
libbpf 1.0: Deprecate bpf_object__find_map_by_offset() API
libbpf 1.0: Deprecate bpf_map__is_offload_neutral()
...
====================
Link: https://lore.kernel.org/r/20220107013626.53943-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The return value of BPF_CGROUP_RUN_PROG_INET{4,6}_POST_BIND() in
__inet_bind() is not handled properly. While the return value
is non-zero, it will set inet_saddr and inet_rcv_saddr to 0 and
exit:
err = BPF_CGROUP_RUN_PROG_INET4_POST_BIND(sk);
if (err) {
inet->inet_saddr = inet->inet_rcv_saddr = 0;
goto out_release_sock;
}
Let's take UDP for example and see what will happen. For UDP
socket, it will be added to 'udp_prot.h.udp_table->hash' and
'udp_prot.h.udp_table->hash2' after the sk->sk_prot->get_port()
called success. If 'inet->inet_rcv_saddr' is specified here,
then 'sk' will be in the 'hslot2' of 'hash2' that it don't belong
to (because inet_saddr is changed to 0), and UDP packet received
will not be passed to this sock. If 'inet->inet_rcv_saddr' is not
specified here, the sock will work fine, as it can receive packet
properly, which is wired, as the 'bind()' is already failed.
To undo the get_port() operation, introduce the 'put_port' field
for 'struct proto'. For TCP proto, it is inet_put_port(); For UDP
proto, it is udp_lib_unhash(); For icmp proto, it is
ping_unhash().
Therefore, after sys_bind() fail caused by
BPF_CGROUP_RUN_PROG_INET4_POST_BIND(), it will be unbinded, which
means that it can try to be binded to another port.
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20220106132022.3470772-2-imagedong@tencent.com
This rework the handling of hci_inquiry_result_with_rssi_evt to not use
a union to represent the different inquiry responses.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As discussed during review here:
https://patchwork.kernel.org/project/netdevbpf/patch/20220105132141.2648876-3-vladimir.oltean@nxp.com/
we should inform developers about pitfalls of concurrent access to the
boolean properties of dsa_switch and dsa_port, now that they've been
converted to bit fields. No other measure than a comment needs to be
taken, since the code paths that update these bit fields are not
concurrent with each other.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic incremental fixup to commits
7787ff7763 ("net: dsa: merge all bools of struct dsa_switch into a single u32")
bde82f389a ("net: dsa: merge all bools of struct dsa_port into a single u8")
The desire to make this change was enunciated after posting these
patches here:
https://patchwork.kernel.org/project/netdevbpf/cover/20220105132141.2648876-1-vladimir.oltean@nxp.com/
but due to a slight timing overlap (message posted at 2:28 p.m. UTC,
merge commit is at 2:46 p.m. UTC), that comment was missed and the
changes were applied as-is.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2022-01-06
1) Fix xfrm policy lookups for ipv6 gre packets by initializing
fl6_gre_key properly. From Ghalem Boudour.
2) Fix the dflt policy check on forwarding when there is no
policy configured. The check was done for the wrong direction.
From Nicolas Dichtel.
3) Use the correct 'struct xfrm_user_offload' when calculating
netlink message lenghts in xfrm_sa_len(). From Eric Dumazet.
4) Tread inserting xfrm interface id 0 as an error.
From Antony Antony.
5) Fail if xfrm state or policy is inserted with XFRMA_IF_ID 0,
xfrm interfaces with id 0 are not allowed.
From Antony Antony.
6) Fix inner_ipproto setting in the sec_path for tunnel mode.
From Raed Salem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2022-01-06
1) Fix some clang_analyzer warnings about never read variables.
From luo penghao.
2) Check for pols[0] only once in xfrm_expand_policies().
From Jean Sacren.
3) The SA curlft.use_time was updated only on SA cration time.
Update whenever the SA is used. From Antony Antony
4) Add support for SM3 secure hash.
From Xu Jia.
5) Add support for SM4 symmetric cipher algorithm.
From Xu Jia.
6) Add a rate limit for SA mapping change messages.
From Antony Antony.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the XDP mem ID inside the page_pool struct so it can be retrieved
later for use in bpf_prog_run().
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/20220103150812.87914-4-toke@redhat.com
Add a new callback function to page_pool that, if set, will be called every
time a new page is allocated. This will be used from bpf_test_run() to
initialise the page data with the data provided by userspace when running
XDP programs with redirect turned on.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/20220103150812.87914-3-toke@redhat.com
The functions that register an XDP memory model take a struct xdp_rxq as
parameter, but the RXQ is not actually used for anything other than pulling
out the struct xdp_mem_info that it embeds. So refactor the register
functions and export variants that just take a pointer to the xdp_mem_info.
This is in preparation for enabling XDP_REDIRECT in bpf_prog_run(), using a
page_pool instance that is not connected to any network device.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20220103150812.87914-2-toke@redhat.com
ieee80211_iterate_active_interfaces() and
ieee80211_iterate_active_interfaces_atomic() already exist, where the
former allows the iterator function to sleep. Add
ieee80211_iterate_stations() which is similar to
ieee80211_iterate_stations_atomic() but allows the iterator to sleep.
This is needed for adding SDIO support to the rtw88 driver. Some
interators there are reading or writing registers. With the SDIO ops
(sdio_readb, sdio_writeb and friends) this means that the iterator
function may sleep.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211228211501.468981-2-martin.blumenstingl@googlemail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch enables the sysctl mtu_expires to be configured per net
namespace.
Signed-off-by: xu xin <xu.xin16@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the sysctl min_pmtu to be configured per net
namespace.
Signed-off-by: xu xin <xu.xin16@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
When finding the socket to report an error on, if the invoking packet
is using Segment Routing, the IPv6 destination address is that of an
intermediate router, not the end destination. Extract the ultimate
destination address from the segment address.
This change allows traceroute to function in the presence of Segment
Routing.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC8754 says:
ICMP error packets generated within the SR domain are sent to source
nodes within the SR domain. The invoking packet in the ICMP error
message may contain an SRH. Since the destination address of a packet
with an SRH changes as each segment is processed, it may not be the
destination used by the socket or application that generated the
invoking packet.
For the source of an invoking packet to process the ICMP error
message, the ultimate destination address of the IPv6 header may be
required. The following logic is used to determine the destination
address for use by protocol-error handlers.
* Walk all extension headers of the invoking IPv6 packet to the
routing extension header preceding the upper-layer header.
- If routing header is type 4 Segment Routing Header (SRH)
o The SID at Segment List[0] may be used as the destination
address of the invoking packet.
Mangle the skb so the network header points to the invoking packet
inside the ICMP packet. The seg6 helpers can then be used on the skb
to find any segment routing headers. If found, mark this fact in the
IPv6 control block of the skb, and store the offset into the packet of
the SRH. Then restore the skb back to its old state.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ICMP error message can contain in its message body part of an IPv6
packet which invoked the error. Such a packet might contain a segment
router header. Export get_srh() so the ICMP code can make use of it.
Since his changes the scope of the function from local to global, add
the seg6_ prefix to keep the namespace clean. And move it into seg6.c
so it is always available, not just when IPV6_SEG6_LWTUNNEL is
enabled.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver offloading ct tuples can use the information of which devices
received the packets that created the offloaded connections, to
more efficiently offload them only to the relevant device.
Add new act_ct nf conntrack extension, which is used to store the skb
devices before offloading the connection, and then fill in the tuple
iifindex so drivers can get the device via metadata dissector match.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same fix in commit 5ec7d18d18 ("sctp: use call_rcu to free endpoint")
is also needed for dumping one asoc and sock after the lookup.
Fixes: 86fdb3448c ("sctp: ensure ep is not destroyed before doing the dump")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-12-30
The following pull-request contains BPF updates for your *net-next* tree.
We've added 72 non-merge commits during the last 20 day(s) which contain
a total of 223 files changed, 3510 insertions(+), 1591 deletions(-).
The main changes are:
1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii.
2) Beautify and de-verbose verifier logs, from Christy.
3) Composable verifier types, from Hao.
4) bpf_strncmp helper, from Hou.
5) bpf.h header dependency cleanup, from Jakub.
6) get_func_[arg|ret|arg_cnt] helpers, from Jiri.
7) Sleepable local storage, from KP.
8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c
commit 077cdda764 ("net/mlx5e: TC, Fix memory leak with rules with internal port")
commit 31108d142f ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
commit 4390c6edc0 ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
https://lore.kernel.org/all/20211229065352.30178-1-saeed@kernel.org/
net/smc/smc_wr.c
commit 49dc9013e3 ("net/smc: Use the bitmap API when applicable")
commit 349d43127d ("net/smc: fix kernel panic caused by race of smc_sock")
bitmap_zero()/memset() is removed by the fix
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
netns/bpf.h gets included by netdevice.h (thru net_namespace.h)
which in turn gets included in a lot of places. We should keep
netns/bpf.h as light-weight as possible.
bpf-netns.h seems to contain more implementation details than
deserves to be included in a netns header. It needs to pull in
uapi/bpf.h to get various enum types.
Move enum netns_bpf_attach_type to netns/bpf.h and invert the
dependency. This makes netns/bpf.h fit the mold of a struct
definition header more clearly, and drops the number of objects
rebuilt when uapi/bpf.h is touched from 7.7k to 1.1k.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211230012742.770642-3-kuba@kernel.org
Add missing includes unmasked by the subsequent change.
Mostly network drivers missing an include for XDP_PACKET_HEADROOM.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211230012742.770642-2-kuba@kernel.org
- Add support for Foxconn MT7922A
- Add support for Realtek RTL8852AE
- Rework HCI event handling to use skb_pull_data
-----BEGIN PGP SIGNATURE-----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=AVll
-----END PGP SIGNATURE-----
Merge tag 'for-net-next-2021-12-29' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Add support for Foxconn MT7922A
- Add support for Realtek RTL8852AE
- Rework HCI event handling to use skb_pull_data
* tag 'for-net-next-2021-12-29' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next: (62 commits)
Bluetooth: MGMT: Fix spelling mistake "simultanous" -> "simultaneous"
Bluetooth: vhci: Set HCI_QUIRK_VALID_LE_STATES
Bluetooth: MGMT: Fix LE simultaneous roles UUID if not supported
Bluetooth: hci_sync: Add check simultaneous roles support
Bluetooth: hci_sync: Wait for proper events when connecting LE
Bluetooth: hci_sync: Add support for waiting specific LE subevents
Bluetooth: hci_sync: Add hci_le_create_conn_sync
Bluetooth: hci_event: Use skb_pull_data when processing inquiry results
Bluetooth: hci_sync: Push sync command cancellation to workqueue
Bluetooth: hci_qca: Stop IBS timer during BT OFF
Bluetooth: btusb: Add support for Foxconn MT7922A
Bluetooth: btintel: Add missing quirks and msft ext for legacy bootloader
Bluetooth: btusb: Add two more Bluetooth parts for WCN6855
Bluetooth: L2CAP: Fix using wrong mode
Bluetooth: hci_sync: Fix not always pausing advertising when necessary
Bluetooth: mgmt: Make use of mgmt_send_event_skb in MGMT_EV_DEVICE_CONNECTED
Bluetooth: mgmt: Make use of mgmt_send_event_skb in MGMT_EV_DEVICE_FOUND
Bluetooth: mgmt: Introduce mgmt_alloc_skb and mgmt_send_event_skb
Bluetooth: btusb: Return error code when getting patch status failed
Bluetooth: btusb: Handle download_firmware failure cases
...
====================
Link: https://lore.kernel.org/r/20211229211258.2290966-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sock.h is pretty heavily used (5k objects rebuilt on x86 after
it's touched). We can drop the include of filter.h from it and
add a forward declaration of struct sk_filter instead.
This decreases the number of rebuilt objects when bpf.h
is touched from ~5k to ~1k.
There's a lot of missing includes this was masking. Primarily
in networking tho, this time.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/bpf/20211229004913.513372-1-kuba@kernel.org
This patch is to delay the endpoint free by calling call_rcu() to fix
another use-after-free issue in sctp_sock_dump():
BUG: KASAN: use-after-free in __lock_acquire+0x36d9/0x4c20
Call Trace:
__lock_acquire+0x36d9/0x4c20 kernel/locking/lockdep.c:3218
lock_acquire+0x1ed/0x520 kernel/locking/lockdep.c:3844
__raw_spin_lock_bh include/linux/spinlock_api_smp.h:135 [inline]
_raw_spin_lock_bh+0x31/0x40 kernel/locking/spinlock.c:168
spin_lock_bh include/linux/spinlock.h:334 [inline]
__lock_sock+0x203/0x350 net/core/sock.c:2253
lock_sock_nested+0xfe/0x120 net/core/sock.c:2774
lock_sock include/net/sock.h:1492 [inline]
sctp_sock_dump+0x122/0xb20 net/sctp/diag.c:324
sctp_for_each_transport+0x2b5/0x370 net/sctp/socket.c:5091
sctp_diag_dump+0x3ac/0x660 net/sctp/diag.c:527
__inet_diag_dump+0xa8/0x140 net/ipv4/inet_diag.c:1049
inet_diag_dump+0x9b/0x110 net/ipv4/inet_diag.c:1065
netlink_dump+0x606/0x1080 net/netlink/af_netlink.c:2244
__netlink_dump_start+0x59a/0x7c0 net/netlink/af_netlink.c:2352
netlink_dump_start include/linux/netlink.h:216 [inline]
inet_diag_handler_cmd+0x2ce/0x3f0 net/ipv4/inet_diag.c:1170
__sock_diag_cmd net/core/sock_diag.c:232 [inline]
sock_diag_rcv_msg+0x31d/0x410 net/core/sock_diag.c:263
netlink_rcv_skb+0x172/0x440 net/netlink/af_netlink.c:2477
sock_diag_rcv+0x2a/0x40 net/core/sock_diag.c:274
This issue occurs when asoc is peeled off and the old sk is freed after
getting it by asoc->base.sk and before calling lock_sock(sk).
To prevent the sk free, as a holder of the sk, ep should be alive when
calling lock_sock(). This patch uses call_rcu() and moves sock_put and
ep free into sctp_endpoint_destroy_rcu(), so that it's safe to try to
hold the ep under rcu_read_lock in sctp_transport_traverse_process().
If sctp_endpoint_hold() returns true, it means this ep is still alive
and we have held it and can continue to dump it; If it returns false,
it means this ep is dead and can be freed after rcu_read_unlock, and
we should skip it.
In sctp_sock_dump(), after locking the sk, if this ep is different from
tsp->asoc->ep, it means during this dumping, this asoc was peeled off
before calling lock_sock(), and the sk should be skipped; If this ep is
the same with tsp->asoc->ep, it means no peeloff happens on this asoc,
and due to lock_sock, no peeloff will happen either until release_sock.
Note that delaying endpoint free won't delay the port release, as the
port release happens in sctp_endpoint_destroy() before calling call_rcu().
Also, freeing endpoint by call_rcu() makes it safe to access the sk by
asoc->base.sk in sctp_assocs_seq_show() and sctp_rcv().
Thanks Jones to bring this issue up.
v1->v2:
- improve the changelog.
- add kfree(ep) into sctp_endpoint_destroy_rcu(), as Jakub noticed.
Reported-by: syzbot+9276d76e83e3bcde6c99@syzkaller.appspotmail.com
Reported-by: Lee Jones <lee.jones@linaro.org>
Fixes: d25adbeb0c ("sctp: fix an use-after-free issue in sctp_sock_dump")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Struct sctp_ep_common is included in both asoc and ep, but hlist_node
and hashent are only needed by ep after asoc_hashtable was dropped by
Commit b5eff71283 ("sctp: drop the old assoc hashtable of sctp").
So it is better to move hlist_node and hashent from sctp_ep_common to
sctp_endpoint, and it saves some space for each asoc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel generates mapping change message, XFRM_MSG_MAPPING,
when a source port chage is detected on a input state with UDP
encapsulation set. Kernel generates a message for each IPsec packet
with new source port. For a high speed flow per packet mapping change
message can be excessive, and can overload the user space listener.
Introduce rate limiting for XFRM_MSG_MAPPING message to the user space.
The rate limiting is configurable via netlink, when adding a new SA or
updating it. Use the new attribute XFRMA_MTIMER_THRESH in seconds.
v1->v2 change:
update xfrm_sa_len()
v2->v3 changes:
use u32 insted unsigned long to reduce size of struct xfrm_state
fix xfrm_ompat size Reported-by: kernel test robot <lkp@intel.com>
accept XFRM_MSG_MAPPING only when XFRMA_ENCAP is present
Co-developed-by: Thomas Egerer <thomas.egerer@secunet.com>
Signed-off-by: Thomas Egerer <thomas.egerer@secunet.com>
Signed-off-by: Antony Antony <antony.antony@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
1) From Shay Drory: Devlink user knobs to control device's EQ size
This series provides knobs which will enable users to
minimize memory consumption of mlx5 Functions (PF/VF/SF).
mlx5 exposes two new generic devlink params for EQ size
configuration and uses devlink generic param max_macs.
LINK: https://lore.kernel.org/netdev/20211208141722.13646-1-shayd@nvidia.com/
2) From Tariq and Lama, allocate software channel objects and statistics
of a mlx5 netdevice private data dynamically upon first demand to save on
memory.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmHClsoACgkQSD+KveBX
+j5d6gf+NKH8mQd6Aa/Gt4Y2DtS7GzN+dPD+2MokuT2YSWU8kVGlMnC01MTE2V2s
jiOUC6ZEbayx2ORzd58XlcfAMEZz2WH8VGLXTdmM3niv13D7AueSsUP5SVK7Oamk
h0bwzOV8CE1Ru5s3Q3zPaLBqTWN+TmyG42HNwYyD8GZT7O5q8iBfor97N2KN5U5u
rhxzFcD2jfhtYxACkjea6RTN9CTM7l9FS4+DIjhu53PAOBaOZLj8NKSYUqP6I17L
ITJDd9za4Nq/YiB2yU4UVNkDEXsuXWoqnTNsL1oEUPForEomJsnikHV9ywzyKVMn
SbWdZOr5C14UBH9wyyauEBBv5oLB7w==
=cotW
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2021-12-21
1) From Shay Drory: Devlink user knobs to control device's EQ size
This series provides knobs which will enable users to
minimize memory consumption of mlx5 Functions (PF/VF/SF).
mlx5 exposes two new generic devlink params for EQ size
configuration and uses devlink generic param max_macs.
LINK: https://lore.kernel.org/netdev/20211208141722.13646-1-shayd@nvidia.com/
2) From Tariq and Lama, allocate software channel objects and statistics
of a mlx5 netdevice private data dynamically upon first demand to save on
memory.
* tag 'mlx5-updates-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Take packet_merge params directly from the RX res struct
net/mlx5e: Allocate per-channel stats dynamically at first usage
net/mlx5e: Use dynamic per-channel allocations in stats
net/mlx5e: Allow profile-specific limitation on max num of channels
net/mlx5e: Save memory by using dynamic allocation in netdev priv
net/mlx5e: Add profile indications for PTP and QOS HTB features
net/mlx5e: Use bitmap field for profile features
net/mlx5: Remove the repeated declaration
net/mlx5: Let user configure max_macs generic param
devlink: Clarifies max_macs generic devlink param
net/mlx5: Let user configure event_eq_size param
devlink: Add new "event_eq_size" generic device param
net/mlx5: Let user configure io_eq_size param
devlink: Add new "io_eq_size" generic device param
====================
Link: https://lore.kernel.org/r/20211222031604.14540-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This allows to identify flows that originate from local machine
in a followup patch.
It would be possible to make this a ->status bit instead.
For now I did not do that yet because I don't have a use-case for
exposing this info to userspace.
If one comes up the toggle can be replaced with a status bit.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Commit d068ca2ae2 ("codel: split into multiple files") moved all
Qdisc-related code to codel_qdisc.h, move the include of pkt_sched.h
as well.
This is similar to the previous commit, although we don't care as
much about incremental builds after pkt_sched.h was touched itself
it is included by net/sch_generic.h which is modified ~20 times
a year.
This decreases the incremental build size after touching pkt_sched.h
from 1592 to 617 objects.
Fix unmasked missing includes in WiFi drivers.
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221193941.3805147-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since sock.h is modified relatively often (60 times in the last
12 months) it seems worthwhile to decrease the incremental build
work.
CoDel's header includes net/inet_ecn.h which in turn includes net/sock.h.
codel.h is itself included by mac80211 which is included by much of
the WiFi stack and drivers. Removing the net/inet_ecn.h include from
CoDel breaks the dependecy between WiFi and sock.h.
Commit d068ca2ae2 ("codel: split into multiple files") moved all
the code which actually needs ECN helpers out to net/codel_impl.h,
the include can be moved there as well.
This decreases the incremental build size after touching sock.h
from 4999 objects to 4051 objects.
Fix unmasked missing includes in WiFi drivers.
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221193941.3805147-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If controller/driver don't support LE simultaneous roles its UUID shall
be omitted when responding to MGMT_OP_READ_EXP_FEATURES_INFO.
This also rework the support introducing HCI_LE_SIMULTANEOUS_ROLES flag
so it can be detected when userspace wants to use or not.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This attempts to check if the controller can act as both central and
peripheral simultaneously and in case it does skip suspending
advertising or in case of directed advertising don't fail if scanning.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds support for waiting for specific LE subevents instead of
command status which may only indicate that the commands is in progress
and a different event is used to complete the operation.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds hci_le_create_conn_sync and make hci_le_connect use it instead
of queueing multiple commands which may conflict with the likes of
hci_update_passive_scan which uses hci_cmd_sync_queue.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
syzbot reported that hci_cmd_sync_cancel may sleep from the wrong
context. To avoid this, create a new work item that pushes the relevant
parts into a different context.
Note that we keep the old implementation with the name
__hci_cmd_sync_cancel as the sleeping behaviour is desired in some
cases.
Reported-and-tested-by: syzbot+485cc00ea7cf41dfdbf1@syzkaller.appspotmail.com
Fixes: c97a747efc ("Bluetooth: btusb: Cancel sync commands for certain URB errors")
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add new device generic parameter to determine the size of the
asynchronous control events EQ.
For example, to reduce event EQ size to 64, execute:
$ devlink dev param set pci/0000:06:00.0 \
name event_eq_size value 64 cmode driverinit
$ devlink dev reload pci/0000:06:00.0
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add new device generic parameter to determine the size of the
I/O completion EQs.
For example, to reduce I/O EQ size to 64, execute:
$ devlink dev param set pci/0000:06:00.0 \
name io_eq_size value 64 cmode driverinit
$ devlink dev reload pci/0000:06:00.0
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
* ndo_fill_forward_path support in mac80211, to let
drivers use it
* association comeback notification for userspace,
to be able to react more sensibly to long delays
* support for background radar detection hardware
in some chipsets
* SA Query Procedures offload on the AP side
* more logging if we find problems with HT/VHT/HE
* various cleanups and minor fixes
-----BEGIN PGP SIGNATURE-----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=u1jf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have:
* ndo_fill_forward_path support in mac80211, to let drivers use it
* association comeback notification for userspace, to be able
to react more sensibly to long delays
* support for background radar detection hardware in some chipsets
* SA Query Procedures offload on the AP side
* more logging if we find problems with HT/VHT/HE
* various cleanups and minor fixes
Conflicts:
net/wireless/reg.c:
e08ebd6d7b ("cfg80211: Acquire wiphy mutex on regulatory work")
701fdfe348 ("cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface")
https://lore.kernel.org/r/20211221111950.57ecc6a7@canb.auug.org.au
drivers/net/wireless/ath/ath10k/wmi.c:
7f599aeccb ("cfg80211: Use the HE operation IE to determine a 6GHz BSS channel")
3bf2537ec2 ("ath10k: drop beacon and probe response which leak from other channel")
https://lore.kernel.org/r/20211221115004.1cd6b262@canb.auug.org.au
* tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (32 commits)
cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface
rfkill: allow to get the software rfkill state
cfg80211: refactor cfg80211_get_ies_channel_number()
nl82011: clarify interface combinations wrt. channels
nl80211: Add support to offload SA Query procedures for AP SME device
nl80211: Add support to set AP settings flags with single attribute
mac80211: add more HT/VHT/HE state logging
cfg80211: Use the HE operation IE to determine a 6GHz BSS channel
cfg80211: rename offchannel_chain structs to background_chain to avoid confusion with ETSI standard
mac80211: Notify cfg80211 about association comeback
cfg80211: Add support for notifying association comeback
mac80211: introduce channel switch disconnect function
cfg80211: Fix order of enum nl80211_band_iftype_attr documentation
cfg80211: simplify cfg80211_chandef_valid()
mac80211: Remove a couple of obsolete TODO
mac80211: fix FEC flag in radio tap header
mac80211: use coarse boottime for airtime fairness code
ieee80211: change HE nominal packet padding value defines
cfg80211: use ieee80211_bss_get_elem() instead of _get_ie()
mac80211: Use memset_after() to clear tx status
...
====================
Link: https://lore.kernel.org/r/20211221112532.28708-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In previous method each AP settings flag is represented by a top-level
flag attribute and conversion to enum cfg80211_ap_settings_flags had to
be done before sending them to driver. This commit is to make it easier
to define new AP settings flags and sending them to driver.
This commit also deprecate sending of
%NL80211_ATTR_EXTERNAL_AUTH_SUPPORT in %NL80211_CMD_START_AP. But to
maintain backwards compatibility checks for
%NL80211_ATTR_EXTERNAL_AUTH_SUPPORT in %NL80211_CMD_START_AP when
%NL80211_ATTR_AP_SETTINGS_FLAGS not present in %NL80211_CMD_START_AP.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Link: https://lore.kernel.org/r/1637911519-21306-1-git-send-email-vjakkam@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A non-collocated AP whose primary channel is not a PSC channel
may transmit a duplicated beacon on the corresponding PSC channel
in which it would indicate its true primary channel.
Use this inforamtion contained in the HE operation IE to determine
the primary channel of the AP.
In case of invalid infomration ignore it and use the channel
the frame was received on.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211202143322.71eb2176e54e.I130f678e4aa390973ab39d838bbfe7b2d54bff8e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ETSI standard defines "Offchannel CAC" as:
"Off-Channel CAC is performed by a number of non-continuous checks
spread over a period in time. This period, which is required to
determine the presence of radar signals, is defined as the Off-Channel
CAC Time..
Minimum Off-Channel CAC Time 6 minutes and Maximum Off-Channel CAC Time
4 hours..".
mac80211 implementation refers to a dedicated hw chain used for continuous
radar monitoring. Rename offchannel_* references to background_* in
order to avoid confusion with ETSI standard.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/4204cc1d648d76b44557981713231e030a3bd991.1638190762.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thought the underline driver MLME can handle association temporal
rejection with comeback, it is still useful to notify this to
user space, as user space might want to handle the temporal
rejection differently. For example, in case the comeback time
is too long, user space can deauthenticate immediately and try
to associate with a different AP.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211129152938.2467809e8cb3.I45574185b582666bc78eef0c29a4c36b478e5382@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce a disconnect function that can be used when a
channel switch error occurs. The channel switch can request to
block the tx, and so, we need to make sure we do not send a deauth
frame in this case.
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211129152938.cd2a615a0702.I9edb14785586344af17644b610ab5be109dcef00@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add process to validate flags of filter and actions when adding
a tc filter.
We need to prevent adding filter with flags conflicts with its actions.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add reoffload process to update hw_count when driver
is inserted or removed.
We will delete the action if it is with skip_sw flag and
not offloaded to any hardware in reoffload process.
When reoffloading actions, we still offload the actions
that are added independent of filters.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When collecting stats for actions update them using both
hardware and software counters.
Stats update process should not run in context of preempt_disable.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename exts stats update functions with hw for readability.
We make this change also to update stats from hw for an action
when it is offloaded to hw as a single action.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add skip_hw and skip_sw for user to control if offload the action
to hardware.
We also add in_hw_count for user to indicate if the action is offloaded
to any hardware.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use flow_indr_dev_register/flow_indr_dev_setup_offload to
offload tc action.
We need to call tc_cleanup_flow_action to clean up tc action entry since
in tc_setup_action, some actions may hold dev refcnt, especially the mirror
action.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new ops to tc_action_ops for flow action setup.
Refactor function tc_setup_flow_action to use this new ops.
We make this change to facilitate to add standalone action module.
We will also use this ops to offload action independent of filter
in following patch.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To improves readability, we rename offload functions with offload instead
of flow.
The term flow is related to exact matches, so we rename these functions
with offload.
We make this change to facilitate single action offload functions naming.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add index to flow_action_entry structure and delete index from police and
gate child structure.
We make this change to offload tc action for driver to identify a tc
action.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ct rejects a flow, it removes the conntrack info from the skb.
act_ct sets the post_ct variable so the dissector will see this case
as an +tracked +invalid state, but the zone id is lost with the
conntrack info.
To restore the zone id on such cases, set the last executed zone,
via the tc control block, when passing ct, and read it back in the
dissector if there is no ct info on the skb (invalid connection).
Fixes: 7baf2429a1 ("net/sched: cls_flower add CT_FLAGS_INVALID flag support")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BPF layer extends the qdisc control block via struct bpf_skb_data_end
and because of that there is no more room to add variables to the
qdisc layer control block without going over the skb->cb size.
Extend the qdisc control block with a tc control block,
and move all tc related variables to there as a pre-step for
extending the tc control block with additional members.
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that there is only one fib nla_policy there is no need to
keep the macro around. Place it where its used.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The attributes are identical in all implementations so move the ipv4 one
into the core and remove the per-family nla policies.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>