When the BCM2835 audio output is used, userspace sees a jitter up to 10ms
in the audio position, aka "delay" -- the number of frames that must
be output before a new frame would be played.
Make this a bit nicer for userspace by interpolating the position
using the CPU clock.
The overhead is small -- an extra ktime_get() every time a GPU message
is sent -- and another call and a few calculations whenever the delay
is sought from userland.
At 48,000 frames per second, i.e. approximately 20 microseconds per
frame, it would take a clock inaccuracy of
20 microseconds in 10 milliseconds -- 2,000 parts per million --
to result in an inaccurate estimate, whereas
crystal- or resonator-based clocks typically have an
inaccuracy of 10s to 100s of parts per million.
Signed-off-by: Mike Brady <mikebrady@eircom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following tasks were completed or not the right solution:
1/2- Not the proper solution, we should register a platform device in
vchiq the same way it's done with bcm2835-camera as commented here:
https://lkml.org/lkml/2018/10/16/1131
2/3- Fixed by Takashi Iwai here: https://lkml.org/lkml/2018/9/4/587
Also, adds a new task as per mailing list conversation.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was called bcm2835_alsa0_driver, that "0" didn't mean much.
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There will only be one probe function, there is no use for appendig
"_dt" the end of the name.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In this case explicitly naming the union doesn't help overall code
comprehension and clutters it.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When it comes to declaring variables it's preferred, when possible, to
use an inverted tree organization scheme.
Also, removes some comments that were useless.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memory is being allocated with devres_alloc(), wich ultimately uses
__GFP_ZERO to call kmalloc. We don't need to zero the memory area again
in bcm2835-audio.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device communicates with the audio core using FOURCC codes. The
driver was generating them using different macros/expressions. We now
use the same macro to create them and centralize all the definitions.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, connection.h was only required for the definition of
VCHI_CONNECTION_T, but now all usages of it are gone. Remove this unused
header.
After connection.h is gone, message.h and vchi_cfg_internal.h are no
longer referenced by anything either. Drop them as well.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove two parameters which are never used and all where all callers
just pass in dummy values anyway.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These types are not used anywhere, remove them.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no definition for this unused function, so drop its prototype.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These fields are only initialized with constants and never read. Drop
them.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The connection field of SERVICE_CREATION_T is assigned to but its value
is never read. Drop the field and the resulting no longer needed code
from bcm2835-audio and bcm2835-camera.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These functions do nothing besides returning NULL and are unused.
Just drop them.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang warns:
drivers/staging/vc04_services/bcm2835-camera/controls.c:59:18: warning:
variable 'mains_freq_qmenu' is not needed and will not be emitted
[-Wunneeded-internal-declaration]
static const s64 mains_freq_qmenu[] = {
^
1 warning generated.
This is because mains_freq_qmenu is currently only used in an ARRAY_SIZE
macro, which is a compile time evaluation in this case. Avoid this by
adding mains_freq_qmenu as the imenu member of this structure, which
matches all other controls that uses the ARRAY_SIZE macro in v4l2_ctrls.
This turns out to be a no-op because V4L2_CID_MPEG_VIDEO_BITRATE_MODE is
defined as a MMAL_CONTROL_TYPE_STD_MENU, which does not pass the imenu
definition along to v4l2_ctrl_new in bm2835_mmal_init_controls.
Link: https://github.com/ClangBuiltLinux/linux/issues/122
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the TODO item to remove manual cache flushing from bulk_receive.
This was previously done in this commit:
commit 7e8dbea410 ("staging: bcm2835-camera: Remove explicit cache
flush operations")
Signed-off-by: Aymen Qader <qader.aymen@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the checkpatch.pl error:
ERROR: "foo * bar" should be "foo *bar"
in the interface/vchi directory
Signed-off-by: Aymen Qader <qader.aymen@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the macros and structs associated with the
"vchi_msg_queuev_ex" function, which was previously removed in 49bec49.
Also fixes the checkpatch.pl errors:
ERROR: Macros with complex values should be enclosed in parentheses
ERROR: space required after that ','
Signed-off-by: Aymen Qader <qader.aymen@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the checkpatch.pl error:
ERROR: code indent should use tabs where possible
in the interface/vchi directory
Signed-off-by: Aymen Qader <qader.aymen@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the checkpatch.pl error:
ERROR: space prohibited after/before that open/closed parenthesis
in the interface/vchi directory.
Signed-off-by: Aymen Qader <qader.aymen@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As far as I can tell, this has never been used.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the compatible string in the DTB to select the correct cache line
size for the SoC - 32 for BCM2835, and 64 for BCM2836 and BCM2837.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of creating a dummy child device to manage the card object,
just use devm stuff directly for releasing with snd_card_free().
This results in a lot of code reduction.
Since the dummy child devices are gone, the device object to be passed
to the memory allocator needs to be adjusted as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just a minor code refactoring and adding some const prefix.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All three functions to create PCM objects are fairly resemble, and can
be unified to a single common helper.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent ALSA PCM core supports the SNDRV_PCM_INFO_SYNC_APPLPTR flag
indicating that the driver needs the ack call at each appl_ptr
update. This is requirement for the indirect PCM implementations like
bcm2835-audio driver, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memory access to the pages allocated with
SNDRV_DMA_TYPE_CONTINUOUS are basically non-coherent, and it becomes a
problem when a process accesses via mmap.
For the more consistent access, use the device coherent memory, just
by replacing the call pattern in the allocator helpers.
The only point we need to be careful for is the device object passed
there; since bcm2835-audio driver creates fake devices and each card
is created on top of that, we need to pass its parent device as the
real device object.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For more consistency, move the module parameter description right
after its variable definition.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yet a few header files are included unnecessarily. Drop them.
Also remove trivial comments.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For making the whole code more consistent, replace the home-made debug
print macros with the standard dev_err() & co.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of allocating a separate snd_device object, let snd_card_new()
allocate the private resource. This simplifies the code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the most significant part in the patch series.
The bcm2835-audio driver used to queue the commands to vc04 core via
workqueue, but basically the whole accesses to vc04 core are done in
the sleepable context, including the callback calls. In such a case,
rewriting the code using non-atomic PCM ops will simplify the logic a
lot.
This patch does it: all workqueue are gone and each former-work
implementation is now directly called from PCM ops like trigger and
write transfer.
Along with it, the DMA position updater, bcm2835_playback_fifo(), was
also rewritten to use a simpler logic. Now it handles the XRUN and
draining properly by calling snd_pcm_stop() conditionally.
The current position is kept in atomic_t value so that it can be read
concurrently from the pointer callback.
Also, the bcm2835_audio_instance object is allocated at the beginning
of bcm2835_audio_open(). This makes the resource management clearer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a cleanup and code refactoring in bcm2835-vchiq.c.
The major code changes are to provide local helpers for easier use of
lock / unlock, and message passing with/without response wait. This
allows us to reduce lots of open codes.
Also, the max packet is set at opening the stream, not at each time
when the write gets called.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bcm2835_audio_instance object contains the array of
VCHI_SERVICE_HANDLE_T, while the code assumes and uses only the first
element explicitly. Let's reduce to a single vchi handle for
simplifying the code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It seems that the resolution of vc04 callback is in 10 msec; i.e. the
minimal period size is also 10 msec.
This patch adds the corresponding hw constraint.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chip->audio_mutex is used basically for protecting the opened
stream assignment, and the prepare callback is irrelevant with it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These debug messages worsen the code readability a lot while they give
little debuggability (which we already have via tracing, in anyway).
Let's clean them up. This allows us to reduce the
snd_bcm2835_pcm_lib_ioctl() function to be a direct call of the
snd_pcm_lib_ioctl callback (like most other drivers do), too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the parameter setup fails, the driver should propagate the error
code instead of silently ignoring it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
alsa_stream->chip can be never NULL.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hw_queue_size of PCM indirect helper doesn't need to be set up if
you use the whole given buffer size. Drop the useless
initialization, which just confuses readers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some fields in alsa_stream are the values we keep already in PCM
runtime object, hence they are redundant. Use the standard PCM
runtime values instead of the private copies.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The alsa_stream->lock is never used. Kill it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The handling of SNDRV_PCM_TRIGGER_STOP at the trigger callback is
incorrect: when the STOP is issued, the driver is supposed to drop the
stream immediately. Meanwhile bcm2835 driver checks the DRAINING
state and tries to issue some different command.
This patch straightens things a bit, dropping the incorrect state
checks. The draining behavior would be still not perfect at this
point, but will be improved in a later patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The running flag of alsa_stream is basically useless. The running
state is strictly controlled in ALSA PCM core side, hence the check in
PCM trigger and close callbacks are superfluous.
Also, the prefill ack at trigger start became superfluous nowadays
with the ALSA PCM core update.
Let's rip them off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the alsa_stream->open flag checks in the current code are
redundant, and they cannot be racy. For the code simplification,
let's remove the flag and its check.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bcm2835_audio_setup(), bcm2835_audio_flush_buffers() and
bcm2835_audio_flush_playback_buffers() functions do implement
nothing.
Also, bcm2835_audio_set_ctls() is already called inside
bcm2835_audio_set_params(), so the later call is superfluous.
This patch removes these superfluous implementations.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current code, the mute control is dealt in a special manner,
modifying the current volume and saving the old volume, etc. This is
inconsistent (e.g. change the volume while muted, then unmute), and
way too complex.
Also, the whole volume handling code has conversion between ALSA
volume and raw volume values, which can lead to another
inconsistency and complexity.
This patch simplifies these points:
- The ALSA volume value is saved in chip->volume
- volume->mute saves the mute state
- The mute state is evaluated only when the actual volume is passed to
the hardware, bcm2835_audio_set_ctls()
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The avail_substreams bit mask is checked for the possible racy
accesses, but this cannot happen in practice; i.e. the assignment and
the check are superfluous.
Let's rip them off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only a few of them are really needed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "IEC958 Playback Stream" control does basically the very same
thing as "IEC958 Playback Default" redundantly. The former should
have been stream-specific and restored after closing the stream, but
we don't do in that way.
Since it's nothing but confusion, remove this fake.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
snd-bcm2835 driver takes the lock with mutex_lock_interruptible() in
all places, which don't make sense. Replace them with the simple
mutex_lock().
Also taking a mutex lock right after creating it for each PCM object
is nonsense, too. It cannot be racy at that point. We can get rid of
it.
Last but not least, initializing chip->audio_mutex at each place is
error-prone. Initialize properly at creating the chip object in
snd_bcm2835_create() instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the big staging/iio patches for 4.19-rc1.
Lots of churn here, with tons of cleanups happening in staging drivers,
a removal of an old crypto driver that no one was using (skein), and the
addition of some new IIO drivers. Also added was a "gasket" driver from
Google that needs loads of work and the erofs filesystem.
Even with adding all of the new drivers and a new filesystem, we are
only adding about 1000 lines overall to the kernel linecount, which
shows just how much cleanup happened, and how big the unused crypto
driver was.
All of these have been in the linux-next tree for a while now with no
reported issues.
Note, you will have a merge problem with a device tree IIO file and the
MAINTAINERS file, both resolutions are easy, just take all changed.
There will be a skein file merge issue as well, but that file got
deleted so just drop that.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g+2A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykwGACfQZz3Ncvc7thHkZytxxqQnbx5JpkAn0yV5SvF
yVXG9SA9yCTKVjYczZjZ
=6t/x
-----END PGP SIGNATURE-----
Merge tag 'staging-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here are the big staging/iio patches for 4.19-rc1.
Lots of churn here, with tons of cleanups happening in staging
drivers, a removal of an old crypto driver that no one was using
(skein), and the addition of some new IIO drivers. Also added was a
"gasket" driver from Google that needs loads of work and the erofs
filesystem.
Even with adding all of the new drivers and a new filesystem, we are
only adding about 1000 lines overall to the kernel linecount, which
shows just how much cleanup happened, and how big the unused crypto
driver was.
All of these have been in the linux-next tree for a while now with no
reported issues"
* tag 'staging-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (903 commits)
staging:rtl8192u: Remove unused macro definitions - Style
staging:rtl8192u: Add spaces around '+' operator - Style
staging:rtl8192u: Remove stale comment - Style
staging: rtl8188eu: remove unused mp_custom_oid.h
staging: fbtft: Add spaces around / - Style
staging: fbtft: Erases some repetitive usage of function name - Style
staging: fbtft: Adjust some empty-line problems - Style
staging: fbtft: Removes one nesting level to help readability - Style
staging: fbtft: Changes gamma table to define.
staging: fbtft: A bit more information on dev_err.
staging: fbtft: Fixes some alignment issues - Style
staging: fbtft: Puts macro arguments in parenthesis to avoid precedence issues - Style
staging: rtl8188eu: remove unused array dB_Invert_Table
staging: rtl8188eu: remove whitespace, add missing blank line
staging: rtl8188eu: use is_multicast_ether_addr in rtw_sta_mgt.c
staging: rtl8188eu: remove whitespace - style
staging: rtl8188eu: cleanup block comment - style
staging: rtl8188eu: use is_multicast_ether_addr in rtl8188eu_xmit.c
staging: rtl8188eu: use is_multicast_ether_addr in recv_linux.c
staging: rtlwifi: refactor rtl_get_tcb_desc
...
wait_for_completion_timeout returns unsigned long not int so a variable of
proper type is introduced. Further the check for <= 0 is ambiguous and should
be == 0 here indicating timeout which is the only error case so no additional
check needed here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 7b3ad5abf0 ("staging: Import the BCM2835 MMAL-based V4L2 camera driver.")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wait_for_completion_timeout returns unsigned long not int so a variable of
proper type is introduced. Further the check for <= 0 is ambiguous and
should be == 0 here indicating timeout.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 7b3ad5abf0 ("staging: Import the BCM2835 MMAL-based V4L2 camera driver.")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, if bcm2835_audio_open() fails partway, the allocated
workqueue is leaked. Avoid that.
While at it, propagate the return value of
bcm2835_audio_open_connection() on failure instead of returning -1.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, if allocating a workqueue fails, the driver will probe
successfully but it will silently do nothing, which is rather silly.
So instead bail out with -ENOMEM in bcm2835_audio_open() if
alloc_workqueue() fails, and remove the now pointless checks for a NULL
workqueue.
While at it, get rid of the rather pointless one-line function
my_workqueue_init().
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the device mutex to protect the vb2_queue.
This allows to replace the ad-hoc wait_{prepare, finish}
with vb2_ops_wait_{prepare, finish}.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The pointers vchiq_dbg_dir and vchiq_dbg_clients are local to the
source and do not need to be in global scope, so make them static.
Cleans up sparse warnings:
warning: symbol 'vchiq_dbg_dir' was not declared. Should it be static?
warning: symbol 'vchiq_dbg_clients' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The log entry dentries are only set, never referenced, so no need to
keep them around. Remove the pointer from struct
vchiq_debugfs_log_entry as it is not needed anymore and get rid of the
separate vchiq_debugfs_create_log_entries() function as it is only used
in one place.
Suggested-by: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Keerthi Reddy <keerthigd4990@gmail.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to set this to be int * when it is only used as a void *.
This lets us remove the unneeded cast, and unneeded temporary variable
the one place it is referenced in the code.
Suggested-by: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Keerthi Reddy <keerthigd4990@gmail.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure, and the one static variable that was declared with it,
were not being used for anything. The log_categories field was being
set, but never used again. So just remove it entirely as it is not
needed at all.
Suggested-by: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Keerthi Reddy <keerthigd4990@gmail.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This does not need to be part of a wrapper function, or in a structure,
just properly reference it directly as a single variable.
The whole variable will be going away soon anyway, this is just a step
toward that direction.
Suggested-by: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Keerthi Reddy <keerthigd4990@gmail.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vchiq_debugfs_top() is only a wrapper around a pointer to a dentry, so
just use the dentry directly instead, making it a static variable
instead of part of a static structure.
This also removes the pointless BUG_ON() when checking that dentry as no
one should ever care if debugfs is working or not, and the kernel should
really not panic over something as trivial as that.
Suggested-by: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Keerthi Reddy <keerthigd4990@gmail.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Clean up the vchiq_arm code by not caring about the value of debugfs
calls. This ends up removing a number of lines of code that are not
needed.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Keerthi Reddy <keerthigd4990@gmail.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We just need some integer handles that can map back to our message
struct when we're handling a reply, which struct idr is perfect for.
v2: Fix error check to look at the right variable.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Noticed by Stephen Rothwell in -next.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 4bebb0312e ("staging/bcm2835-camera: Set ourselves up as a platform driver.")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The arg is a u32 *, so switch over to that in our declarations.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes a compiler warning about a set-but-not-used variable. I think
this was just leftover dead code from before set_framerate_params(),
since that also sets up some mmal_parameter_rational structs for fps.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The v4l2 uapi uses u8[] for strings, so cast those to char * to avoid
compiler warnings about unsigned vs signed with sprintf() and friends.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As requested by Mauro Carvalho Chehab in review.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a typo flagged by checkpatch, and another in the same line.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error conditions don't warrant taking the kernel down, so remove
BUG_ON.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct vchiq_mmal_rect is only referenced from mmal-parameters.h, yet
was defined in mmal-vchiq.h.
Move it to avoid having to include multiple headers for no reason.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mmal-parameters.h didn't have the normal
...
protection to stop it being included multiple times. Add it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MMAL and V4L2 buffers had been disassociated, and linked on
demand. Seeing as both are finite and low in number, and we now have
the same number of each, link them for the duration. This removes the
complexity of maintaining lists as the struct mmal_buffer context
comes back from the VPU, so we can directly link back to the relevant
V4L2 buffer.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For historical reasons, the number of buffers passed to the VPU over
MMAL did not match that passed from V4L2. That is a silly situation
as the driver has to duplicate serialisation and other functions that
have already been implemented in V4L2/videobuf2.
As we had more V4L2 buffers than MMAL ones, the MMAL buffer headers
were returned to the VPU immediately on being filled, which is now
invalid.
Match the number of buffers notified in queue_setup with that used in
MMAL. Return buffers only when we get them from V4L2.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no requirement to serialise bulk transfers as that is all
done in VCHI, and if a second MMAL_MSG_TYPE_BUFFER_TO_HOST happened
before the VCHI_CALLBACK_BULK_RECEIVED, then the service_callback
thread is deadlocked.
Remove the bulk_mutex so that multiple receives can be scheduled at a
time.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct mmal_msg_context was being allocated for every message
being sent to the VPU, and freed when it came back. Whilst that is
required behaviour for some messages (mainly the synchronous ones), it
is wasteful for the video buffers that make up the majority of the
traffic.
Add to the buffer_init/cleanup hooks that it allocates/frees the
msg_context required.
v2: changes by anholt from the downstream tree: clean up indentation,
pass an error value through, forward-declare the struct so we have
less void *
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interleaved RGB and single plane YUV formats can be delivered by the
GPU without the secondary step of removing padding, as the
bytesperline field can be set appropriately.
Planar YUV needs the GPU to still remove padding, as there is no way
to report that there is padding between the planes (ie on the height).
The multi-planar formats are NOT applicable, as there is no easy way
to make them contiguous in memory (ie one large allocation that gets
broken up). The whole task is passed across to videobuf2 which has no
notion of that requirement.
v2: Changes by anholt from the downstream driver: Flag two more planar
formats as needing padding removal, and remove broken userspace
workaround.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows bcm2835-camera to automatically probe after VCHI has
loaded, rather than only successfully probing if the arbitrary probe
order chooses us after VCHI.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We had the camera driver set up in a module_init function, but that
meant that the camera driver would fail to load if it was initialized
before VCHI. By attaching to this platform_device, it can get a
defined load order.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since there is no vchiq function listed by "make checkstack" anymore,
we can remove the stack hog issue from the TODO.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This removes an unnecessary break which has been reported by checkpatch.pl.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This removing an unnecessary return which has been reported by checkpatch.pl.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a whitespace issue reported by checkpatch:
ERROR: code indent should use tabs where possible
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The definition of USE_VCHIQ_ARM and VCOS_VERIFY_BKPTS isn't really necessary
so remove them.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chance to mixup i and j is very high. So rename variable j to a more
explaining one.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to make the code easier to review, move the second
abort criterion into the loop and the incrementation into
a separate line.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel would like to have all stack VLA usage removed[1]. The array
here is fixed (declared with a const variable) but it appears like a VLA
to the compiler. Also, currently we are putting 768 bytes on the
stack. This function is only called on the error path so performance is
not critical, let's just allocate the memory instead of using the
stack. This saves stack space and removes the VLA build warning.
kmalloc a buffer for dumping state instead of using the stack.
[1]: https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We better use the real loop limit in the warning about
"too many active services". Another benefit is than we don't have to care
about the format string in the following change.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current implementation, vchi_instance is inited during the first
call of bcm2835_audio_open_connection(), and is never freed. It causes a
memory leak when the module `snd_bcm2835` is removed.
Here is how this commit fixes it:
* the VCHI context (including vchi_instance) is created once in the
platform's devres
* the VCHI context is allocated and connected once during module_init()
* all created bcm2835_chips have a pointer to this VCHI context
* bcm2835_audio_open_connection() can access the VCHI context through the
associated bcm2835_chip
* the VCHI context is disconnected and freed once during module_exit()
After this commit is applied, I don't see other issues with the module's
init/exit, so I also remove the associated TODO task.
Steps to reproduce the memory leak before this commit:
~~~~
root@raspberrypi:/home/pi# aplay test0.wav
Playing WAVE 'test0.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Ster
^CAborted by signal Interrupt...
root@raspberrypi:/home/pi# rmmod snd_bcm2835
root@raspberrypi:/home/pi# modprobe snd_bcm2835
root@raspberrypi:/home/pi# aplay test0.wav
Playing WAVE 'test0.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Ster
^CAborted by signal Interrupt...
root@raspberrypi:/home/pi# echo scan > /sys/kernel/debug/kmemleak
root@raspberrypi:/home/pi# cat /sys/kernel/debug/kmemleak
unreferenced object 0xb6794c00 (size 128):
comm "aplay", pid 406, jiffies 36870 (age 116.650s)
hex dump (first 32 bytes):
08 a5 82 81 01 00 00 00 08 4c 79 b6 08 4c 79 b6 .........Ly..Ly.
00 00 00 00 00 00 00 00 ad 4e ad de ff ff ff ff .........N......
backtrace:
[<802af5e0>] kmem_cache_alloc_trace+0x294/0x3d0
[<806ce620>] vchiq_initialise+0x98/0x1b0
[<806d0b34>] vchi_initialise+0x24/0x34
[<7f1311ec>] 0x7f1311ec
[<7f1303bc>] 0x7f1303bc
[<7f130590>] 0x7f130590
[<7f111fd8>] snd_pcm_open_substream+0x68/0xc4 [snd_pcm]
[<7f112108>] snd_pcm_open+0xd4/0x248 [snd_pcm]
[<7f112334>] snd_pcm_playback_open+0x4c/0x6c [snd_pcm]
[<7f0e250c>] snd_open+0xa8/0x14c [snd]
[<802ce590>] chrdev_open+0xac/0x188
[<802c57b4>] do_dentry_open+0x10c/0x314
[<802c6ba8>] vfs_open+0x5c/0x88
[<802d9a68>] path_openat+0x368/0x944
[<802dacd4>] do_filp_open+0x70/0xc4
[<802c6f70>] do_sys_open+0x110/0x1d4
~~~~
Signed-off-by: Kirill Marinushkin <k.marinushkin@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: devel@driverdev.osuosl.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to free the kthreads in error case before leaving
vchiq_init_state() otherwise we leak resources.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move all calls of wake_up_process to one point, whichs makes the
following implementation of clean-up code easier.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vchiq_initialise() is used in non-interrupt context, so we can
replace udelay with usleep_range as suggested by timers-howto.txt.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Multiline dereferences aren't nice to review. So fix this checkpatch
warning.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's better to use the __func__ macro instead of open-code the function
name. This fixes the following checkpatch warning:
WARNING: Prefer using '"%s...", __func__' to using 'x',
this function's name, in a string
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hiding memset behind a macro isn't the best, because it relies on that
the parameter is not a pointer. Luckily all user has been removed, so
we can remove BITSET_ZERO too.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This removes the stackhog in process_free_queue by allocating the
necessary memory within the recycle thread main function instead
of the stack.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bail out branch in case of a invalid tx_pos missed a semaphore
release. Dan Carpenter found this with a static checker.
Fixes: d1eab9dec6 ("staging: vchiq_core: Bail out in case of invalid tx_pos")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TODO list missed some issues before we can move the driver out of staging.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bcm2835-camera driver has already been imported. So remove it from the TODO.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add blank line after declaration. Issue found with checkpatch.
Signed-off-by: Nishka Dasgupta <nishka.dasgupta_ug18@ashoka.edu.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These are dead code, including in the downstream Raspberry Pi tree.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now we just need to get the other drivers merged and finish the style
cleanups/garbage collecting so we can get out of staging.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's been tempting to replace this with (L1) cache_line_size(), but
that's really not what the value is about. It's about coordinating
the condition for the pagelist fragment behavior between the two
sides. However, the property was not accepted for the upstream DT
binding, so we have to use the firmware's fallback value.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was requested by Rob Herring in DT bindings review.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's not used in-tree, or in the downstream tree.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change 'unsigned *' to 'unsigned int *'. Issue found with checkpatch.
Signed-off-by: Nishka Dasgupta <nishka.dasgupta_ug18@ashoka.edu.in>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Format multiline comment by moving '*/' to a new line. Issue found with
checkpatch.
Signed-off-by: Nishka Dasgupta <nishka.dasgupta_ug18@ashoka.edu.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add blank line after declaration. Issue found with checkpatch.
Signed-off-by: Nishka Dasgupta <nishka.dasgupta_ug18@ashoka.edu.in>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two incompatible definitions of 'vchiq_instance_struct', so
passing them through vchiq_initialise(), vchiq_connect() or another
such interface is broken, as shown by building the driver with link-time
optimizations:
drivers/staging/vc04_services/interface/vchiq_arm/vchiq_if.h:129:0: error: type of 'vchiq_initialise' does not match original declaration [-Werror=lto-type-mismatch]
extern VCHIQ_STATUS_T vchiq_initialise(VCHIQ_INSTANCE_T *pinstance);
drivers/staging/vc04_services/interface/vchiq_arm/vchiq_kern_lib.c:68:0: note: 'vchiq_initialise' was previously declared here
VCHIQ_STATUS_T vchiq_initialise(VCHIQ_INSTANCE_T *instance_out)
drivers/staging/vc04_services/interface/vchiq_arm/vchiq_kern_lib.c:68:0: note: code may be misoptimized unless -fno-strict-aliasing is used
drivers/staging/vc04_services/interface/vchiq_arm/vchiq_if.h:131:0: error: type of 'vchiq_connect' does not match original declaration [-Werror=lto-type-mismatch]
extern VCHIQ_STATUS_T vchiq_connect(VCHIQ_INSTANCE_T instance);
drivers/staging/vc04_services/interface/vchiq_arm/vchiq_kern_lib.c:168:0: note: 'vchiq_connect' was previously declared here
VCHIQ_STATUS_T vchiq_connect(VCHIQ_INSTANCE_T instance)
It's possible that only one of the two sides actually access the members,
but it's clear that they need to agree on the layout. The easiest way
to achieve this appears to be to merge the two files into one. I tried
moving the structure definition into a shared header first, but ended
up running into too many interdependencies that way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All thoses files are not used by anybody.
Lets just remove them.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all
drivers/staging/vc04_services/bcm2835-camera/ files, that identifies the
license in a specific and legally-defined manner. So the extra GPL text
wording can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: <bcm-kernel-feedback-list@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Fix up the bcm2835-camera driver to have a proper SPDX identifier, based
on the license text in the file itself. The SPDX identifier is a
legally binding shorthand, which can be used instead of the full boiler
plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: <bcm-kernel-feedback-list@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all
drivers/staging/vc04_services/bcm2835-audio/ files, that identifies the
license in a specific and legally-defined manner. So the extra GPL text
wording can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: <bcm-kernel-feedback-list@broadcom.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Fix up the bcm2835-audio driver to have a proper SPDX identifier, based
on the license text in the file itself. The SPDX identifier is a
legally binding shorthand, which can be used instead of the full boiler
plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: <bcm-kernel-feedback-list@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix some errors for wrong brace position reported by checkpatch.
Signed-off-by: Sidong Yang <realwakka@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coccinelle suggested to use BUG_ON instead of if condition followed by BUG
but BUG_ON should be used in situations where integrity of the system is no
longer guaranteed. In this case, as suggested by Stefan Wahren, vchiq isn't
critical.
Since it is not critical, BUG_ON should be avoided.
Replaced if condition followed by BUG with WARN_ON_ONCE.
Signed-off-by: Kishore KP <kishore.p@techveda.org>
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removed .owner field initialization, platform core does it automatically.
Pointed out by Coccinelle.
Signed-off-by: Kishore KP <kishore.p@techveda.org>
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This removes checkpatch.pl warnings:
WARNING: Block comments use a trailing */ on a separate line
WARNING: Block comments should align the * on each line
WARNING: Block comments use * on subsequent lines
Signed-off-by: Mikhail Shvetsov <lameli67@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix checkpatch errors relating to open brace placement for enums and
function definitions.
Signed-off-by: Tara Null <tn@fastmail.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix brace on next line coding style errors reported by
checkpatch.
Signed-off-by: Tomas Marek <marek_tomas@centrum.cz>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was found using checkpatch.pl's EMBEDDED_FUNCTION_NAME warning.
It is easier to be consistent and always use __func__ instead of having
to remember to update any hardcoded references to the original name.
Signed-off-by: Genki Sky <sky@genki.is>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was found using checkpatch.pl's SPLIT_STRING warning. While joining
these strings makes for long lines, the kernel codebase consistently
does it this way to make user-visible strings easier to grep for.
Signed-off-by: Genki Sky <sky@genki.is>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was found using checkpatch.pl's MULTILINE_DEREFERENCE warning.
Putting the dereference onto one line makes them easier to read,
especially when part of a larger expression (in this case, function
arguments and ternary operator), and when the dereferences are short
(as they are here).
Signed-off-by: Genki Sky <sky@genki.is>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct timeval is deprecated for in-kernel use, and converting
this function to use ktime_t makes it simpler as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull get_user_pages_fast() conversion from Al Viro:
"A bunch of places switched to get_user_pages_fast()"
* 'work.get_user_pages_fast' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ceph: use get_user_pages_fast()
pvr2fs: use get_user_pages_fast()
atomisp: use get_user_pages_fast()
st: use get_user_pages_fast()
via_dmablit(): use get_user_pages_fast()
fsl_hypervisor: switch to get_user_pages_fast()
rapidio: switch to get_user_pages_fast()
vchiq_2835_arm: switch to get_user_pages_fast()
Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd atomisp
cleanups (take the media tree's version).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnFrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymxbwCgtNlBkqD2JJYpLRKvI/C4w1vzZsEAnA2THRkt
g3ioPBqmqC/2DSbldr2o
=/ebw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd
atomisp cleanups (take the media tree's version)"
* tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits)
staging: lustre: add SPDX identifiers to all lustre files
staging: greybus: Remove redundant license text
staging: greybus: add SPDX identifiers to all greybus driver files
staging: ccree: simplify ioread/iowrite
staging: ccree: simplify registers access
staging: ccree: simplify error handling logic
staging: ccree: remove dead code
staging: ccree: handle limiting of DMA masks
staging: ccree: copy IV to DMAable memory
staging: fbtft: remove redundant initialization of buf
staging: sm750fb: Fix parameter mistake in poke32
staging: wilc1000: Fix bssid buffer offset in Txq
staging: fbtft: fb_ssd1331: fix mirrored display
staging: android: Fix checkpatch.pl error
staging: greybus: loopback: convert loopback to use generic async operations
staging: greybus: operation: add private data with get/set accessors
staging: greybus: loopback: Fix iteration count on async path
staging: greybus: loopback: Hold per-connection mutex across operations
staging: greybus/loopback: use ktime_get() for time intervals
staging: fsl-dpaa2/eth: Extra headroom in RX buffers
...
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Additionally removes invalid NULL check, as pointed out by Dan Carpenter.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Michael Zoran <mzoran@crowfest.net>
Cc: Keerthi Reddy <keerthigd4990@gmail.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: devel@driverdev.osuosl.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary braces for single statements also declare a local
variable "platform_state" of type "struct vchiq_2835_state", to
avoid the multiple cast.
Signed-off-by: Mihaela Muraru <mihaela.muraru21@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use identifier __func__ instead of the name of the function.
Issue found by checkpatch.pl.
Signed-off-by: Mihaela Muraru <mihaela.muraru21@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the unnecessary '*' character and align the comment block to fit
the coding style used by linux kernel organization.
Signed-off-by: Mihaela Muraru <mihaela.muraru21@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous commit (0adbfd46) fixed a memory leak but also freed a
block in the success case, causing a stale pointer to be used with
potentially fatal results. Only free the vchi_instance block in the
case that vchi_connect fails; once connected, the instance is
retained for subsequent connections.
Simplifying the code by removing a bunch of gotos and returning errors
directly.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Fixes: 0adbfd4694 ("staging: bcm2835-audio: fix memory leak in bcm2835_audio_open_connection()")
Cc: stable <stable@vger.kernel.org> # 4.12+
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pr_err() messages should end with a new-line to avoid other messages
being concatenated.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes typedef from struct and renames it from "typedef
struct vchiq_2835_state_struct" to "struct vchiq_2835_state" as per
kernel coding standards.
Signed-off-by: Mihaela Muraru <mihaela.muraru21@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes extern variable vchiq_arm_log_level, because it is
already declared in vchiq_arm.h
Issue found by checkpatch.pl
Signed-off-by: Mihaela Muraru <mihaela.muraru21@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the volatile fields of bcm2835_alsa_stream -
control and status are not used.
$ grep bcm2835_alsa_stream
>From the above command all instances we see that
all variables of 'bcm2835_alsa_stream' are declared as
'alsa_stream'
So search for 'control' wherever we have 'alsa_stream'
$ grep -l 'alsa_stream' | xargs grep "control"
The above command returns where we don't any usage of
'control' field. which means that there is no usage of
these fields.
similarly for 'status' we see no usages.
Signed-off-by: Keerthi Reddy <keerthigd4990@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use BIT macro instead of left shift
Signed-off-by: Keerthi Reddy <keerthigd4990@gmail.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some words are misspelled. Fix typos.
Signed-off-by: Keerthi Reddy <keerthigd4990@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Blank lines use up extra space in file and makes the file
larger. So do not use multiple blanklines
Signed-off-by: Keerthi Reddy <keerthigd4990@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BCM2835_VCHIQ_SUPPORT_MEMDUMP lets you look through any user memory.
That's too big of an information leak from a security perspective. The
debugging dumps need to be more specific to this driver.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a NULL pointer dereference on RPi 2 with multi_v7_defconfig.
The function page_address() could return NULL with enabled CONFIG_HIGHMEM.
So fix this by using kmap() instead.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 71bad7f086 ("staging: add bcm2708 vchiq driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes a spelling mistake in the comments.
Problem found using checkpatch.
Signed-off-by: Meghana Madhyastha <meghana.madhyastha@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make this const as it is only used in a copy operation.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These vb2_ops structures are only stored in the ops field of a
vb2_queue structure, which is declared as const. Thus the vb2_ops
structures themselves can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make these const as they are only used during a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for snd_pcm_ops structures that are only stored in the ops field of
a snd_soc_platform_driver structure or passed as the third argument to
snd_pcm_set_ops. The corresponding field or parameter is declared const,
so snd_pcm_ops structures that have this property can be declared as
const also.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_pcm_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_platform_driver e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i;
expression e1, e2; position p;
@@
snd_pcm_set_ops(e1, e2, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_pcm_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_pcm_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves a merge issue and gets the vmbox drm driver into this
branch to be able to start taking fixes for it...
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If vchiq_debugfs_init() fails, then we accidentally return a valid
pointer casted to int on error. This code is simpler if we get rid of
the "ptr_err" variable and just use "err" throughout.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This development cycle resulted in a fair amount of changes in both
core and driver sides. The most significant change in ALSA core is
about PCM. Also the support of of-graph card and the new DAPM widget
for DSP are noteworthy changes in ASoC core. And there're lots of
small changes splat over the tree, as you can see in diffstat.
Below are a few highlights:
ALSA core:
- Removal of set_fs() hackery from PCM core stuff, and the code
reorganization / optimization thereafter
- Improved support of PCM ack ops, and a new ABI for improved
control/status mmap handling
- Lots of constifications in various codes
ASoC core:
- The support of of-graph card, which may work as a better generic
device for a replacement of simple-card
- New widget types intended mainly for use with DSPs
ASoC drivers:
- New drivers for Allwinner V3s SoCs
- Ensonic ES8316 codec support
- More Intel SKL and KBL works
- More device support for Intel SST Atom (mostly for cheap tablets and
2-in-1 devices)
- Support for Rockchip PDM controllers
- Support for STM32 I2S and S/PDIF controllers
- Support for ZTE AUD96P22 codecs
HD-audio:
- Support of new Realtek codecs (ALC215/ALC285/ALC289), more quirks
for HP and Dell machines
- A few more fixes for i915 component binding
Note that of-graph change may bring the conflicts with a later pull
request of devicetree, as currently found in linux-next.
-----BEGIN PGP SIGNATURE-----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=PUEh
-----END PGP SIGNATURE-----
Merge tag 'sound-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This development cycle resulted in a fair amount of changes in both
core and driver sides. The most significant change in ALSA core is
about PCM. Also the support of of-graph card and the new DAPM widget
for DSP are noteworthy changes in ASoC core. And there're lots of
small changes splat over the tree, as you can see in diffstat.
Below are a few highlights:
ALSA core:
- Removal of set_fs() hackery from PCM core stuff, and the code
reorganization / optimization thereafter
- Improved support of PCM ack ops, and a new ABI for improved
control/status mmap handling
- Lots of constifications in various codes
ASoC core:
- The support of of-graph card, which may work as a better generic
device for a replacement of simple-card
- New widget types intended mainly for use with DSPs
ASoC drivers:
- New drivers for Allwinner V3s SoCs
- Ensonic ES8316 codec support
- More Intel SKL and KBL works
- More device support for Intel SST Atom (mostly for cheap tablets
and 2-in-1 devices)
- Support for Rockchip PDM controllers
- Support for STM32 I2S and S/PDIF controllers
- Support for ZTE AUD96P22 codecs
HD-audio:
- Support of new Realtek codecs (ALC215/ALC285/ALC289), more quirks
for HP and Dell machines
- A few more fixes for i915 component binding"
* tag 'sound-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (418 commits)
ALSA: hda - Fix unbalance of i915 module refcount
ASoC: Intel: Skylake: Remove driver debugfs exit
ASoC: Intel: Skylake: explicitly add the headers sst-dsp.h
ALSA: hda/realtek - Remove GPIO_MASK
ALSA: hda/realtek - Fix typo of pincfg for Dell quirk
ALSA: pcm: add a documentation for tracepoints
ALSA: atmel: ac97c: fix error return code in atmel_ac97c_probe()
ALSA: x86: fix error return code in hdmi_lpe_audio_probe()
ASoC: Intel: Skylake: Add support to read firmware registers
ASoC: Intel: Skylake: Add sram address to sst_addr structure
ASoC: Intel: Skylake: Debugfs facility to dump module config
ASoC: Intel: Skylake: Add debugfs support
ASoC: fix semicolon.cocci warnings
ASoC: rt5645: Add quirk override by module option
ASoC: rsnd: make arrays path and cmd_case static const
ASoC: audio-graph-card: add widgets and routing for external amplifier support
ASoC: audio-graph-card: update bindings for amplifier support
ASoC: rt5665: calibration should be done before jack detection
ASoC: rsnd: constify dev_pm_ops structures.
ASoC: nau8825: change crosstalk-bypass property to bool type
...
This replaces all remaining BUG_ON with WARN_ON. So in case of
a VCHIQ bug the system is still usable.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Properly handle the error case in case of an invalid tx_pos.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bail out properly if the process index doesn't match the remote insert.
We also drop the BUG in case the process index is at local insert,
so we can trigger the WARN_ON again some steps later.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the ref counter of service has an unexpected value then we better
bail out.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the unlikely case that service is NULL we should bail out instead
of calling BUG_ON(). The other BUG_ON calls will be fixed in separate
patches.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VCHIQ suspend and resume isn't implemented, but even it was
there is no need to call BUG().
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case VCHIQ state is already initialized we need to bailout
in order to aovid a memory leak.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the ARM side of VCHIQ support only 1 state, we could simplify
the init code. This makes it possible to avoid BUG_ON and a theoretical
overflow of id.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the PAGE_MASK instead of open code it.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case vmalloc_to_page returns NULL create_pagelist must abort
imediatly.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Assuming the intension of the function is to clean up, so fix the function
name accordingly.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reduce the indentation within vchiq_dump_service_use_state in order
to avoid a multiline derefernce.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This comment was apparently forgotten in the correction of CamelCase.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable slot_mem_size is assigned a value which is never used.
This issue has been found by CppCheck.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can reduce the scope of the counting variable i. This has
been found by CppCheck.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of saving the return value of mutex_lock_killable in a
local variable we could use the value directly.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the indirect-PCM transfer helper gives back an error, we
should return the error from ack callbacks.
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
vchiq_arm supports transfers less than one page and at arbitrary
alignment, using the dma-mapping API to perform its cache maintenance
(even though the VPU drives the DMA hardware). Read (DMA_FROM_DEVICE)
operations use cache invalidation for speed, falling back to
clean+invalidate on partial cache lines, with writes (DMA_TO_DEVICE)
using flushes.
If a read transfer has ends which aren't page-aligned, performing cache
maintenance as if they were whole pages can lead to memory corruption
since the partial cache lines at the ends (and any cache lines before or
after the transfer area) will be invalidated. This bug was masked until
the disabling of the cache flush in flush_dcache_page().
Honouring the requested transfer start- and end-points prevents the
corruption.
Fixes: cf9caf1929 ("staging: vc04_services: Replace dmac_map_area with dmac_map_sg")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Cc: stable <stable@vger.kernel.org> # 4.10
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gstreamer's v4l2src reacted poorly to certain outputs from the bcm2835
video driver's ioctl ops function vidioc_enum_framesizes, so a
workaround was created that could be activated by user input. This
workaround would replace the driver's ioctl ops struct with another,
similar struct--only with no function pointed to by
vidioc_enum_framesizes. With no response, gstreamer would attempt to
continue with some default settings that happened to work better.
However, this bug has been fixed in gstreamer since 2014, so we
shouldn't include this workaround in the stable version of the driver.
Signed-off-by: Kevin Wern <kevin.m.wern@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vchi_cfg.h: fix checkpatch ERROR: Macros with complex values should be enclosed in parenthesis
Signed-off-by: Haim Daniel <haimdaniel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary log messages in the driver which are just tracking
function entry and exits.
Signed-off-by: Aishwarya Pant <aishpant@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
trivial fix to spelling mistake in various comments and pr_debug messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Regarding to the header the driver is licensed under BSD and GPL.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The firmware for the Raspberry PI already supports simultanous output
of audio through both the HDMI and the Headphone jack. The current
implementation of ALSA doesn't expose this well to user mode since
the firmware audio is represented as a single card.
A newer approach is taken here and a virtual card is created for each
output(HDMI, Headphones, and Traditional ALSA). The firmware has
the concept of channels or streams for which the number to use is
passed in the device tree. These streams are allocated to each of the
virtual cards.
As a side effect of this change, since each output is represented
independenly it's now very easy to use PulseAudio to control the
priorities of the outputs.
Testing:
Audacity and VLC were both loaded at the same time. Each application
was assigned to a different card. With this change I was able to play
different music files at the same time through the HDMI and Headphones
jacks and control the audio independently.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
https://github.com/raspberrypi/linux/issues/1447
port_parameter_get() failed to account for the header
(u32 id and u32 size) in the size before memcpying
the response into the response buffer, so overrunning
the provided buffer by 8 bytes.
Account for those bytes, and also a belt-and-braces
check to ensure we never copy more than *value_size
bytes into value.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
Tested-by: Michael Zoran <mzoran@crowfest.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding the 'bool' symbol brought back a randconfig build bug that
I had fixed before:
drivers/staging/built-in.o: In function `vchiq_probe':
(.text+0x1da30): undefined reference to `rpi_firmware_get'
drivers/staging/built-in.o: In function `vchiq_platform_init':
(.text+0x27494): undefined reference to `rpi_firmware_property'
The problem is that when RASPBERRYPI_FIRMWARE is a loadable module,
but BCM2835_VCHIQ can again be built-in. Making BCM_VIDEOCORE
itself tristate will make Kconfig honor the dependency correctly.
Fixes: 6bbfe4a761 ("staging: vc04_services: Create new BCM_VIDEOCORE setting for VideoCore services.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, if pservice is null then service is set to NULL and immediately
afterwards service is dereferenced causing a null pointer dereference. Fix
this by bailing out early of the function with a null return.
Detected by CoverityScan, CID#1419681 ("Explicit null dereferenced")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using typedef for a structure type and upper case struct names is not
suggested in Linux kernel coding style guidelines. Hence, occurences
of typedefs have been removed and struct names converted to lowercase
in the file. Grep was also used to ensure that all occurence of the
typedefs have been removed. The module compiles without any warnings
or errors.
Script 1:
@r1@
type T;
@@
typedef struct { ... } T;
@script:python c1@
T2;
T << r1.T;
@@
if T[-2:] =="_T":
coccinelle.T2 = T[:-2].lower();
print T
else:
coccinelle.T2=T.lower();
@r2@
type r1.T;
identifier c1.T2;
@@
-typedef
struct
+ T2
{ ... }
-T
;
@r3@
type r1.T;
identifier c1.T2;
@@
- T
+ struct T2
Script 2:
@@
typedef VCHIQ_ELEMENT_T;
@@
(
- VCHIQ_ELEMENT_T
+ struct vchiq_element
)
Signed-off-by: Gargi Sharma <gs051095@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function prototype is for a function that is not even in
the kernel, and hence has been removed.
The type VCHIQ_SHARED_MEM_INFO_T is not used anywhere in the
kernel as well.
Signed-off-by: Gargi Sharma <gs051095@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These four functions are not used and report errors with sparse.
Signed-off-by: Jean-Baptiste Abbadie <jb@abbadie.fr>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In bcm2835_audio_open_connection(), if VCHI connection fails or
initialisation of VCHI audio instance fails vchi_instance needs to be
deallocated otherwise it will cause a memory leak.
Signed-off-by: Aishwarya Pant <aishpant@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch de-allocates work when queue_work(..) fails in the
bcm2835-audio work functions
Signed-off-by: Aishwarya Pant <aishpant@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Refactor conditional to check if memory allocation has failed and
immediately return (-ENOMEM); if block for success case is removed.
* Return the error value -EBUSY when queue_work() fails.
Signed-off-by: Aishwarya Pant <aishpant@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is better to propagate PTR_ERR value instead of a hardcoded value
(-EPERM here)
Signed-off-by: Aishwarya Pant <aishpant@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
