Define the 2.12 bzImage boot protocol: add xloadflags and additional
fields to allow the command line, initramfs and struct boot_params to
live above the 4 GiB mark.
The xloadflags now communicates if this is a 64-bit kernel with the
legacy 64-bit entry point and which of the EFI handover entry points
are supported.
Avoid adding new read flags to loadflags because of claimed
bootloaders testing the whole byte for == 1 to determine bzImageness
at least until the issue can be researched further.
This is based on patches by Yinghai Lu and David Woodhouse.
Originally-by: Yinghai Lu <yinghai@kernel.org>
Originally-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1359058816-7615-26-git-send-email-yinghai@kernel.org
Cc: Rob Landley <rob@landley.net>
Cc: Gokul Caushik <caushik1@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Joe Millenbach <jmillenbach@gmail.com>
Pull small x86 fixes from Peter Anvin:
"A collection of very small fixes, mostly pure documentation."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, doc: Document that bootloader ID 4 is used also by iPXE
x86, doc: Add a formal bootloader ID for kexec-tools
x86, 8042: Enable A20 using KBC to fix S3 resume on some MSI laptops
Add bootloader id D for kexec-tools (it is kexec-tools, not the kexec
system call, that builds the data structures, therefore it is
kexec-tools which is the "bootloader" for this purpose.)
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/50C95832.5030306@zytor.com
Fixes some minor issues in the x86 boot documentation.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Rob Landley <rob@landley.net>
Link: http://lkml.kernel.org/r/20121026031702.GA23828@www.outflux.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pul x86/efi changes from Ingo Molnar:
"This tree adds an EFI bootloader handover protocol, which, once
supported on the bootloader side, will make bootup faster and might
result in simpler bootloaders.
The other change activates the EFI wall clock time accessors on x86-64
as well, instead of the legacy RTC readout."
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: Handover Protocol
x86-64/efi: Use EFI to deal with platform wall clock
Assign a bootloader ID for Sebastian Plotz' "Minimal Linux Bootloader"
(http://sebastian-plotz.blogspot.de). Sebastian has agreed to make
this the pilot for the use of extended boot loader IDs, so this is
assigned version ID 0x11 (avoid assigning 0x10 for now to catch bugs
with people putting E in the primary ID but leaving the extended ID as
zero.)
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Sebastian Plotz <sebastian-plotz@web.de>
Link: http://lkml.kernel.org/n/tip-nq318h0okuaem8x9dpv9854k@git.kernel.org
As things currently stand, traditional EFI boot loaders and the EFI
boot stub are carrying essentially the same initialisation code
required to setup an EFI machine for booting a kernel. There's really
no need to have this code in two places and the hope is that, with
this new protocol, initialisation and booting of the kernel can be
left solely to the kernel's EFI boot stub. The responsibilities of the
boot loader then become,
o Loading the kernel image from boot media
File system code still needs to be carried by boot loaders for the
scenario where the kernel and initrd files reside on a file system
that the EFI firmware doesn't natively understand, such as ext4, etc.
o Providing a user interface
Boot loaders still need to display any menus/interfaces, for example
to allow the user to select from a list of kernels.
Bump the boot protocol number because we added the 'handover_offset'
field to indicate the location of the handover protocol entry point.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Acked-and-Tested-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1342689828-16815-1-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The real-mode kernel header init_size field is located at 0x260 per the field
listing in th e"REAL-MODE KERNEL HEADER" section. It is listed as 0x25c in
the "DETAILS OF HEADER FIELDS" section, which overlaps with pref_address.
Correct the details listing to 0x260.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Link: http://lkml.kernel.org/r/541cf88e2dfe5b8186d8b96b136d892e769a68c1.1310441260.git.dvhart@linux.intel.com
CC: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This integrates the XZ decompression code to the x86 pre-boot code.
mkpiggy.c is updated to reserve about 32 KiB more buffer safety margin for
kernel decompression. It is done unconditionally for all decompressors to
keep the code simpler.
The XZ decompressor needs around 30 KiB of heap, so the heap size is
increased to 32 KiB on both x86-32 and x86-64.
Documentation/x86/boot.txt is updated to list the XZ magic number.
With the x86 BCJ filter in XZ, XZ-compressed x86 kernel tends to be a few
percent smaller than the equivalent LZMA-compressed kernel.
Signed-off-by: Lasse Collin <lasse.collin@tukaani.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alain Knaff <alain@knaff.lu>
Cc: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Cc: Phillip Lougher <phillip@lougher.demon.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86 bootprotocol 2.07 has introduced hardware_subarch ID in the boot
parameters provided by FW. We use it to identify Moorestown platforms.
[ tglx: Cleanup and paravirt fix ]
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
A long ago, in days of yore, it all began with a god named Thor.
There were vikings and boats and some plans for a Linux kernel
header. Unfortunately, a single 8-bit field was used for bootloader
type and version. This has generally worked without *too* much pain,
but we're getting close to flat running out of ID fields.
Add extension fields for both type and version. The type will be
extended if it the old field is 0xE; the version is a simple MSB
extension.
Keep /proc/sys/kernel/bootloader_type containing
(type << 4) + (ver & 0xf) for backwards compatiblity, but also add
/proc/sys/kernel/bootloader_version which contains the full version
number.
[ Impact: new feature to support more bootloaders ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Modify field names to the right ones:
- start_sys was changed to start_sys_seg
- iinitrd_addr_max was changed to ramdisk_max
- pad2 was changed to pad2 and pad3
- readmode_swtch was changed to realmode_swtch
Signed-off-by: Baodong Chen <[email]chenbdchenbd@gmail.com[email]>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: documentation
Update the boot protocol specification to include the currently
supported file formats and their magic numbers.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: clarify documentation
Documentation/x86/boot.txt describes payload_offset as the offset
from the end of the real-mode code. In fact, it is more accurately
described as the offset from the beginning of the protected-mode
code, as (a) this is how it is actually calculated and (b) the padding
after the real-mode code is not included in the offset.
Signed-off-by: Philipp Kohlbecher <xt28@gmx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: documentation fix
I met okuji-san (GRUB maintainer) yesterday.
He said GRuB isn't correct spelled and he want to fix it.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The boot protocol, USB legacy support, and zero-page documentation is
common to the x86 platform, not i386-specific.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
2008-07-22 15:34:38 -04:00
Renamed from Documentation/x86/i386/boot.txt (Browse further)