This patch extends the kirkwood's PCIe support up to 2 controllers as in the 6282 devices.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Add private_data pointer to the pci_sys_data, this pointer can be
used for holding platform specific data for each pci controller.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
The 6282 SoC is compatible to 6280 and features faster CPU, DDR3, additional
PCIe interface, and LCD controller. More information can be found here:
http://www.marvell.com/products/processors/embedded/armada_300/armada_310.pdf
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
In case the board is configured to boot from spi flash, the mpps
will not be configured to select the NAND I/Os. This patch makes
sure to select the NAND I/O's regardless to the boot device type.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Some platforms, such as the DNS-323 rev C requires the soft reset line
to be toggled on and back off for the reset to work.
Note: The choice of 200ms delay comes from the 2.6.12 based vendor kernel.
It seems to be a -lot- though and I had my device working fine with much
smaller delays but better safe...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This patch adds the base support for this new HW revision to the existing
dns323-setup.c file. The SoC seems to be the same as rev B1, the GPIOs
are all wired differently though and the fan control isn't i2c based
anymore.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This patch adds support for the OpenRD Ultimate machine (could be found
at http://www.arm.linux.org.uk/developer/machines/list.php?id=2884)
Signed-off-by: Dmytro Milinevskyy <milinevskyy@gmail.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Patch found in QNAPs vendor source package, with some cleanups
(proper defines, shortened max. timeout from 1s to 200ms).
Without this patch the PCIe SATA controller (Marvell 88sx7042/sata_mv)
in my QNAP TS-419P (Marvell 88f6281/Kirkwood) stops working after a
few minutes.
The symptomes are described in this thread:
http://marc.info/?l=linux-ide&m=124822863706181&w=2
[ Note: this is a workaround in need of a better analysis/solution -- NP ]
Acked-by: Saeed Bishara <saeed@marvell.com>
Tested-by: Bernhard R. Link <brl@pcpool00.mathematik.uni-freiburg.de>
Seconded-by: Martin Michlmayr <tbm@cyrius.com>
I'm_not_very_happy_with_it-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Add support for the HP t5325 Thin Client. This thin client is based
on a Marvell Kirkwood chip at 1.2 GHz and features 512 MB RAM, 512 MB
SATA-attached flash and an XGI Volari Z11 GPU.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
MPP44 can be used to differentiate between one-bay (TS-11x) and
two-bay (TS-21x) devices.
According to an engineer from QNAP, the setting of MPP44 depends
on the firmware rather than hardware. Presumably, this means
that you could fake the MPP44 value by changing the boot loader.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Add MPP definitions for Marvell Kirkwood 88F6282 revision.
Update some defines to reflect datasheet's MPP names.
Signed-off-by: Benjamin Zores <benjamin.zores@alcatel-lucent.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Among other changes, commit b2a731aa ("D-link DNS-323 revision A1 power
LED") changed the default behaviour of the power LED from solid to
blinking. This was done to match the original DNS-323 firmware which
blinks during the boot process and sets the LED to solid when booting
has completed. However, the downside of this behaviour is that it
requires userland code to change the LED, even for those who don't
care about the behaviour of the original firmware. Therefore, change
it to solid again and let those who care about the original behaviour
change the behaviour from userland.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
On the QNAP TS-41x, MPP45 is used to show the setting of jumper JP1.
Fix the documentation to explain what the settings really indicate.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Export GPIO 45 which is used to indicate the setting of the JP1
jumper. This is useful for userland tools, such as qcontrol, to
see whether the LCD or a serial console is connected.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Fix the following warning :
WARNING: vmlinux.o(.text+0x95a0): Section mismatch in reference from the
function qnap_tsx1x_register_flash() to the (unknown reference) .init.data:(unknown)
The function qnap_tsx1x_register_flash() references
the (unknown reference) __initdata (unknown).
This is often because qnap_tsx1x_register_flash lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
From: Bin Yang <bin.yang@marvell.com>
Cc: stable@kernel.org
Signed-off-by: Bin Yang <bin.yang@marvell.com>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'arm/defconfig/reduced-v2.6.35-rc1' of git://git.pengutronix.de/git/ukl/linux-2.6:
ARM: reduce defconfigs
This is a big change, but results in no loss of information, despite us
losing almost 200k lines:
177 files changed, 652 insertions(+), 194157 deletions(-)
and Grant Likely thinks powerpc can also use the same reduction
technique.
The python script that did the reduction looks like this:
#! /usr/bin/env python
# vim: set fileencoding=utf-8 :
# Copyright (C) 2010 by Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
import re
import subprocess
import os
import sys
# This prevents including a timestamp in the .config which makes comparing a
# bit easier.
os.environ['KCONFIG_NOTIMESTAMP'] = 'Yes, please'
# XXX: get these using getopt
kernel_tree = '' # os.path.join(os.environ['HOME'], 'gsrc', 'linux-2.6')
arch = 'arm'
target = sys.argv[1]
defconfig_src = os.path.join(kernel_tree, 'arch/%s/configs/%s' % (arch, target))
subprocess.check_call(['make', '-s', 'ARCH=%s' % arch, target])
origconfig = list(open('.config'))
config = list(origconfig)
config_size = os.stat('.config').st_size
i = 0
while i < len(config):
print 'test for %r' % config[i]
defconfig = open(defconfig_src, 'w')
defconfig.writelines(config[:i])
defconfig.writelines(config[i + 1:])
defconfig.close()
subprocess.check_call(['make', '-s', 'ARCH=%s' % arch, target])
if os.stat('.config').st_size == config_size and list(open('.config')) == origconfig:
del config[i]
else:
i += 1
defconfig = open(defconfig_src, 'w')
defconfig.writelines(config)
defconfig.close()
which is pretty self-explanatory.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CPU: Testing write buffer coherency: ok
------------[ cut here ]------------
WARNING: at kernel/lockdep.c:3145 check_flags+0xcc/0x1dc()
Modules linked in:
[<c0035120>] (unwind_backtrace+0x0/0xf8) from [<c0355374>] (dump_stack+0x20/0x24)
[<c0355374>] (dump_stack+0x20/0x24) from [<c0060c04>] (warn_slowpath_common+0x58/0x70)
[<c0060c04>] (warn_slowpath_common+0x58/0x70) from [<c0060c3c>] (warn_slowpath_null+0x20/0x24)
[<c0060c3c>] (warn_slowpath_null+0x20/0x24) from [<c008f224>] (check_flags+0xcc/0x1dc)
[<c008f224>] (check_flags+0xcc/0x1dc) from [<c00945dc>] (lock_acquire+0x50/0x140)
[<c00945dc>] (lock_acquire+0x50/0x140) from [<c0358434>] (_raw_spin_lock+0x50/0x88)
[<c0358434>] (_raw_spin_lock+0x50/0x88) from [<c00fd114>] (set_task_comm+0x2c/0x60)
[<c00fd114>] (set_task_comm+0x2c/0x60) from [<c007e184>] (kthreadd+0x30/0x108)
[<c007e184>] (kthreadd+0x30/0x108) from [<c0030104>] (kernel_thread_exit+0x0/0x8)
---[ end trace 1b75b31a2719ed1c ]---
possible reason: unannotated irqs-on.
irq event stamp: 3
hardirqs last enabled at (2): [<c0059bb0>] finish_task_switch+0x48/0xb0
hardirqs last disabled at (3): [<c002f0b0>] ret_slow_syscall+0xc/0x1c
softirqs last enabled at (0): [<c005f3e0>] copy_process+0x394/0xe5c
softirqs last disabled at (0): [<(null)>] (null)
Fix this by ensuring that the lockdep interrupt state is manipulated in
the appropriate places. We essentially treat userspace as an entirely
separate environment which isn't relevant to lockdep (lockdep doesn't
monitor userspace.) We don't tell lockdep that IRQs will be enabled
in that environment.
Instead, when creating kernel threads (which is a rare event compared
to entering/leaving userspace) we have to update the lockdep state. Do
this by starting threads with IRQs disabled, and in the kthread helper,
tell lockdep that IRQs are enabled, and enable them.
This provides lockdep with a consistent view of the current IRQ state
in kernel space.
This also revert portions of 0d928b0b61
which didn't fix the problem.
Tested-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MTU wallclock timing fix-up patch was hardwired to the DB8500
causing a regression. This makes it work on the DB5500 as well.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, the 32-bit and 64-bit atomic operations on ARM do not
include memory constraints in the inline assembly blocks. In the
case of barrier-less operations [for example, atomic_add], this
means that the compiler may constant fold values which have actually
been modified by a call to an atomic operation.
This issue can be observed in the atomic64_test routine in
<kernel root>/lib/atomic64_test.c:
00000000 <test_atomic64>:
0: e1a0c00d mov ip, sp
4: e92dd830 push {r4, r5, fp, ip, lr, pc}
8: e24cb004 sub fp, ip, #4
c: e24dd008 sub sp, sp, #8
10: e24b3014 sub r3, fp, #20
14: e30d000d movw r0, #53261 ; 0xd00d
18: e3011337 movw r1, #4919 ; 0x1337
1c: e34c0001 movt r0, #49153 ; 0xc001
20: e34a1aa3 movt r1, #43683 ; 0xaaa3
24: e16300f8 strd r0, [r3, #-8]!
28: e30c0afe movw r0, #51966 ; 0xcafe
2c: e30b1eef movw r1, #48879 ; 0xbeef
30: e34d0eaf movt r0, #57007 ; 0xdeaf
34: e34d1ead movt r1, #57005 ; 0xdead
38: e1b34f9f ldrexd r4, [r3]
3c: e1a34f90 strexd r4, r0, [r3]
40: e3340000 teq r4, #0
44: 1afffffb bne 38 <test_atomic64+0x38>
48: e59f0004 ldr r0, [pc, #4] ; 54 <test_atomic64+0x54>
4c: e3a0101e mov r1, #30
50: ebfffffe bl 0 <__bug>
54: 00000000 .word 0x00000000
The atomic64_set (0x38-0x44) writes to the atomic64_t, but the
compiler doesn't see this, assumes the test condition is always
false and generates an unconditional branch to __bug. The rest of the
test is optimised away.
This patch adds suitable memory constraints to the atomic operations on ARM
to ensure that the compiler is informed of the correct data hazards. We have
to use the "Qo" constraints to avoid hitting the GCC anomaly described at
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=44492 , where the compiler
makes assumptions about the writeback in the addressing mode used by the
inline assembly. These constraints forbid the use of auto{inc,dec} addressing
modes, so it doesn't matter if we don't use the operand exactly once.
Cc: stable@kernel.org
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The atomic64_add_unless function compares an atomic variable with
a given value and, if they are not equal, adds another given value
to the atomic variable. The function returns zero if the addition
did not occur and non-zero otherwise.
On ARM, the return value is initialised to 1 in C code. Inline assembly
code then performs the atomic64_add_unless operation, setting the
return value to 0 iff the addition does not occur. This means that
when the addition *does* occur, the value of ret must be preserved
across the inline assembly and therefore requires a "+r" constraint
rather than the current one of "=&r".
Thanks to Nicolas Pitre for helping to spot this.
Cc: stable@kernel.org
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On i.MX35 the L2X0_AUX_CTRL register does not have sensible reset
default values. Allow them to be overwritten with the aux_val/aux_mask
arguments passed to l2x0_init().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes on wrong function name in include/plat/sdhci.h for Samsung.
The 's5pc100_default_sdhci0()' function should be chnaged to
's5pv210_default_sdhci0()'. Because 's5pv210_default_sdhci0()' must be pair.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The S5P6442 PLL setting announce message incorrectly displays S5P6440
as the SoC. Change it to S5P6442.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes the following compilation problem if only NCP machine
is selected:
arch/arm/mach-s3c64xx/s3c6410.c: In function 's3c6410_map_io':
arch/arm/mach-s3c64xx/s3c6410.c:51: error: implicit declaration of function 's3c6410_default_sdhci2'
And also adds missed 's3c6400_default_sdhci2'.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fix and added comments]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
1. Corrected shift values of I2S and UART clocks (CLK_GATE_IP3), which were
defined incorrectly.
2. Corrected shift values of sclk_audio, uclk1, sclk_fimd, sclk_mmc,
sclk_spi, sclk_pwm, which had duplicated .enable/.ctrlbit with their
twins defined in struct clk init_clocks_disable[] and struct clk
init_clocks[]. We've changed their .enable/.ctrlbit to use CLK_SRC_MASK
register to avoid the duplicated clock problem described below.
NOTE: Duplicated Clock Problem
Please note that each clock definition should access different control
register; otherwise, the system may suffer lockups. For example, if we
have two clock definitions "a" and "b" which access the same register
(and the shift value). Then, when we do:
module A
clk = clk_get("a");
clk->clk_enable(clk);
module B (context switch)
clk = clk_get("b");
clk->clk_enable(clk);
do something with clk.
clk->clk_disable(clk);
module A (context switch)
do something with clk
* At this point, the system may hang.
Therefore, there should be no clock definitions with the same contol
register/shift. If we need to create "aliases", then, creating child
clocks sharing the clock should be fine.
3. Corrected other sclk_* shift values and access registers.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title and message fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes bug on eint type set function, s5p_irq_eint_set_type().
In the IRQ_TYPE_EDGE_FALLING case, S5P_EXTINT_FALLEDGE is right
instead of S5P_EXTINT_RISEEDGE
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Hardware performance counters on ARM are 32-bits wide but atomic64_t
variables are used to represent counter data in the hw_perf_event structure.
The armpmu_event_update function right-shifts a signed 64-bit delta variable
and adds the result to the event count. This can lead to shifting in sign-bits
if the MSB of the 32-bit counter value is set. This results in perf output
such as:
Performance counter stats for 'sleep 20':
18446744073460670464 cycles <-- 0xFFFFFFFFF12A6000
7783773 instructions # 0.000 IPC
465 context-switches
161 page-faults
1172393 branches
20.154242147 seconds time elapsed
This patch ensures that the delta value is treated as unsigned so that the
right shift sets the upper bits to zero.
Cc: <stable@kernel.org>
Acked-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
RealView boards with certain revisions of the L210/L220 cache controller
may have issues (hardware deadlock) with the mandatory barriers (DSB
followed by an L2 cache sync) when ARM_DMA_MEM_BUFFERABLE is enabled.
The patch disables ARM_DMA_MEM_BUFFERABLE for these boards.
Tested-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
RealView boards with certain revisions of the L220 cache controller (ARM11*
processors only) may have issues (hardware deadlock) with the recent changes to
the mb() barrier implementation (DSB followed by an L2 cache sync). The patch
redefines the RealView ARM11MPCore mandatory barriers without the outer_sync()
call.
Cc: <stable@kernel.org>
Tested-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CPU performance event counters on v7 cores will only operate
if either the NIDEN or DBGEN signals are driven high.
For the OMAP3 platform, these signals are driven low by default
but DBGEN can be asserted by selecting the OMAP3_EMU Kconfig option,
which enables the virtual clock for hardware debugging peripherals.
Acked-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linux expects that if a CPU modifies a memory location, then that
modification will eventually become visible to other CPUs in the system.
On an ARM11MPCore processor, loads are prioritised over stores so it is
possible for a store operation to be postponed if a polling loop immediately
follows it. If the variable being polled indirectly depends on the outstanding
store [for example, another CPU may be polling the variable that is pending
modification] then there is the potential for deadlock if interrupts are
disabled. This deadlock occurs in the KGDB testsuire when executing on an
SMP ARM11MPCore configuration.
This patch changes the definition of cpu_relax() to smp_mb() for ARMv6 cores,
forcing a flushing of the write buffer on SMP systems before the next load
takes place. If the Kernel is not compiled for SMP support, this will expand
to a barrier() as before.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When not aligned, random bits could be written in the initial page table
by the __create_page_tables() function.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When not aligned, random bits could be written in the initial page table
by the __create_page_tables() function.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit f4d6477f introduced a workaround for the lack of hardware
broadcasting of the cache maintenance operations on ARM11MPCore.
However, the workaround is only valid on CPUs that do not do speculative
loads into the D-cache.
This patch adds a Kconfig option with the corresponding help to make the
above clear. When the DMA_CACHE_RWFO option is disabled, the kernel
behaviour is that prior to the f4d6477f commit. This also allows ARMv6
UP processors with speculative loads to work correctly.
For other processors, a different workaround may be needed.
Cc: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A recent patch for DMA cache maintenance on ARM11MPCore added a write
for ownership trick to the v6_dma_inv_range() function. Such operation
destroys data already present in the buffer. However, this function is
used with with dma_sync_single_for_device() which is supposed to
preserve the existing data transfered into the buffer. This patch adds a
combination of read/write for ownership to preserve the original data.
Reported-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This macro is not defined when !CONFIG_MMU so this patch moves the
CONSISTENT_* definitions to the CONFIG_MMU section.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
