Bruno Prémont and Dunphy, Bill noticed me that NILFS will certainly
hang on ARM-based targets.
I found this was caused by an underflow of dirty pages counter. A
b-tree cache routine was marking page dirty without adjusting page
account information.
This fixes the dirty page accounting leak and resolves the hang on
arm-based targets.
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Reported-by: Dunphy, Bill <WDunphy@tandbergdata.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Cc: stable <stable@kernel.org>
When restart a transaction during a truncate operation, we drop and
reacquire i_data_sem. After reacquiring i_data_sem, we need to
discard any inode-based preallocation that might have been grabbed
while we released i_data_sem (for example, if pdflush is allocating
blocks and racing against the truncate).
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9p: fix readdir corner cases
9p: fix readlink
9p: fix a small bug in readdir for long directories
This reverts commit d0646f7b63, as
requested by Eric Sandeen.
It can basically cause an ext4 filesystem to miss recovery (and thus get
mounted with errors) if the journal checksum does not match.
Quoth Eric:
"My hand-wavy hunch about what is happening is that we're finding a
bad checksum on the last partially-written transaction, which is
not surprising, but if we have a wrapped log and we're doing the
initial scan for head/tail, and we abort scanning on that bad
checksum, then we are essentially running an unrecovered filesystem.
But that's hand-wavy and I need to go look at the code.
We lived without journal checksums on by default until now, and at
this point they're doing more harm than good, so we should revert
the default-changing commit until we can fix it and do some good
power-fail testing with the fixes in place."
See
http://bugzilla.kernel.org/show_bug.cgi?id=14354
for all the gory details.
Requested-by: Eric Sandeen <sandeen@redhat.com>
Cc: Theodore Tso <tytso@mit.edu>
Cc: Alexey Fisher <bug-track@fisher-privat.net>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Mathias Burén <mathias.buren@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch below also addresses a couple of other corner cases in readdir
seen with a large (e.g. 64k) msize. I'm not sure what people think of
my co-opting of fid->aux here. I'd be happy to rework if there's a better
way.
When the size of the user supplied buffer passed to readdir is smaller
than the data returned in one go by the 9P read request, v9fs_dir_readdir()
currently discards extra data so that, on the next call, a 9P read
request will be issued with offset < previous offset + bytes returned,
which voilates the constraint described in paragraph 3 of read(5) description.
This patch preseves the leftover data in fid->aux for use in the next call.
Signed-off-by: Jim Garlick <garlick@llnl.gov>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
I do not know if you've looked on the patch, but unfortunately it is
incorrect. A suggested better version is in this email (the old
version didn't work in case the user provided buffer was not long
enough - it incorrectly appended null byte on a position of last char,
and thus broke the contract of the readlink method). However, I'm
still not sure this is 100% correct thing to do, I think readlink is
supposed to return buffer without last null byte in all cases, but we
do return last null byte (even the old version).. on the other hand it
is likely unspecified what is in the remaining part of the buffer, so
null character may be fine there ;):
Signed-off-by: Martin Stava <martin.stava@gmail.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Here is a proposed patch for bug in readdir. Listing of dirs with
many files fails without this patch.
Signed-off-by: Martin Stava <martin.stava@gmail.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Commit 451a9ebf accidentally broke bio_alloc() and bio_kmalloc() comments by
(almost) swapping them.
This patch fixes that, by placing the comments in the right place.
Signed-off-by: Alberto Bertogli <albertito@blitiri.com.ar>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
In bio_put()'s comment, add bio_clone() to the list of functions that can
give you a bio reference.
Signed-off-by: Alberto Bertogli <albertito@blitiri.com.ar>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The xfs_quota returns ENOSYS when remove command is executed.
Reproducable with following steps.
# mount -t xfs -o uquota /dev/sda7 /mnt/mp1
# xfs_quota -x -c off -c remove
XFS_QUOTARM: Function not implemented.
The remove command is allowed during quotaoff, but xfs_fs_set_xstate()
checks whether quota is running, and it leads to ENOSYS.
To solve this problem, add a check for X_QUOTARM.
Signed-off-by: Ryota Yamauchi <r-yamauchi@vf.jp.nec.com>
Signed-off-by: Utako Kusaka <u-kusaka@wm.jp.nec.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Commit bd16956599 seems
to have a slight regression where this code path:
if (!--searchdistance) {
/*
* Not in range - save last search
* location and allocate a new inode
*/
...
goto newino;
}
doesn't free the temporary cursor (tcur) that got dup'd in
this function.
This leaks an item in the xfs_btree_cur zone, and it's caught
on module unload:
===========================================================
BUG xfs_btree_cur: Objects remaining on kmem_cache_close()
-----------------------------------------------------------
It seems like maybe a single free at the end of the function might
be cleaner, but for now put a del_cursor right in this code block
similar to the handling in the rest of the function.
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently the f_fsid of struct kstatfs returned from ocfs2_statfs() is
undefined (vfs layer fills in 0 as default). Since in some conditions,
f_fsid value might be used in a (f_fsid, ino) pair to uniquely identify
a file, ocfs2 should return a unique defined f_fsid value from
ocfs2_statfs().
Because uuid_str is the same on big or litlle endian machine, it's
endian consistent to use osb->uuid_str to generate f_fsid value.
Signed-off-by: Coly Li <coly.li@suse.de>
Cc: Sunil Mushran <sunil.mushran@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
backing-dev: ensure that a removed bdi no longer has super_block referencing it
block: use after free bug in __blkdev_get
block: silently error unsupported empty barriers too
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFSv4: The link() operation should return any delegation on the file
NFSv4: Fix two unbalanced put_rpccred() issues.
NFSv4: Fix a bug when the server returns NFS4ERR_RESOURCE
nfs: Panic when commit fails
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/ppc64: Use preempt_schedule_irq instead of preempt_schedule
powerpc: Minor cleanup to lib/Kconfig.debug
powerpc: Minor cleanup to sound/ppc/Kconfig
powerpc: Minor cleanup to init/Kconfig
powerpc: Limit memory hotplug support to PPC64 Book-3S machines
powerpc: Limit hugetlbfs support to PPC64 Book-3S machines
powerpc: Fix compile errors found by new ppc64e_defconfig
powerpc: Add a Book-3E 64-bit defconfig
powerpc/booke: Fix xmon single step on PowerPC Book-E
powerpc: Align vDSO base address
powerpc: Fix segment mapping in vdso32
powerpc/iseries: Remove compiler version dependent hack
powerpc/perf_events: Fix priority of MSR HV vs PR bits
powerpc/5200: Update defconfigs
drivers/serial/mpc52xx_uart.c: Use UPIO_MEM rather than SERIAL_IO_MEM
powerpc/boot/dts: drop obsolete 'fsl5200-clocking'
of: Remove nested function
mpc5200: support for the MAN mpc5200 based board mucmc52
mpc5200: support for the MAN mpc5200 based board uc101
A particular fsfuzzer run caused an hfs file system to crash on mount.
This is due to a corrupted MDB extent record causing a miscalculation of
HFS_I(inode)->first_blocks for the extent tree. If the extent records are
zereod out, it won't trigger the first_blocks special case. Instead it
falls through to the extent code which we're still in the middle of
initializing.
This patch catches the 0 size extent records, reports the corruption, and
fails the mount.
Reported-by: Ramon de Carvalho Valle <rcvalle@linux.vnet.ibm.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As found in <http://bugs.debian.org/550010>, hfsplus is using type u32
rather than sector_t for some sector number calculations.
In particular, hfsplus_get_block() does:
u32 ablock, dblock, mask;
...
map_bh(bh_result, sb, (dblock << HFSPLUS_SB(sb).fs_shift) + HFSPLUS_SB(sb).blockoffset + (iblock & mask));
I am not confident that I can find and fix all cases where a sector number
may be truncated. For now, avoid data loss by refusing to mount HFS+
volumes with more than 2^32 sectors (2TB).
[akpm@linux-foundation.org: fix 32 and 64-bit issues]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Given such a long name, the kB count in /proc/meminfo's HardwareCorrupted
line is being shown too far right (it does align with x86_64's VmallocChunk
above, but I hope nobody will ever have that much corrupted!). Align it.
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The old reflink fails to handle inodes with inline data and will oops
if it encounters them. This patch copies inline data to the new inode.
Extended attributes may still be refcounted.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Tested-by: Tristan Ye <tristan.ye@oracle.com>
As its name ocfs2_complete_reflink indicates, it should
be called after all the work for reflink is done, so
it really should be called after we reflink xattr
successfully.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Tested-by: Tristan Ye <tristan.ye@oracle.com>
In case of non-modular kernels the root filesystem is mounted by trying
several filesystems. If ocfs2 was tried before the actual filesystem
type, the mount would fail because ocfs2_sb_probe() returns -EAGAIN
instead of -EINVAL. ocfs2 will now return -EINVAL properly.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Reported-by: Laszlo Attila Toth <panther@balabit.hu>
The hugetlb dependencies presently depend on SUPERH && MMU while the
hugetlb page size definitions depend on CPU_SH4 or CPU_SH5. This
unfortunately allows SH-3 + MMU configurations to enable hugetlbfs
without a corresponding HPAGE_SHIFT definition, resulting in the build
blowing up.
As SH-3 doesn't support variable page sizes, we tighten up the
dependenies a bit to prevent hugetlbfs from being enabled. These days
we also have a shiny new SYS_SUPPORTS_HUGETLBFS, so switch to using
that rather than adding to the list of corner cases in fs/Kconfig.
Reported-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
commit 0762b8bde9
(from 14 months ago) introduced a use-after-free bug which has just
recently started manifesting in my md testing.
I tried git bisect to find out what caused the bug to start
manifesting, and it could have been the recent change to
blk_unregister_queue (48c0d4d4c0) but the results were inconclusive.
This patch certainly fixes my symptoms and looks correct as the two
calls are now in the same order as elsewhere in that function.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commits 29fba38b (nfs41: lease renewal) and fc01cea9 (nfs41: sequence
operation) introduce a couple of put_rpccred() calls on credentials for
which there is no corresponding get_rpccred().
See http://bugzilla.kernel.org/show_bug.cgi?id=14249
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
RFC 3530 states that when we recieve the error NFS4ERR_RESOURCE, we are not
supposed to bump the sequence number on OPEN, LOCK, LOCKU, CLOSE, etc
operations. The problem is that we map that error into EREMOTEIO in the XDR
layer, and so the NFSv4 middle-layer routines like seqid_mutating_err(),
and nfs_increment_seqid() don't recognise it.
The fix is to defer the mapping until after the middle layers have
processed the error.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Actually pass the NFS_FILE_SYNC option to the server to avoid a
Panic in nfs_direct_write_complete() when a commit fails.
At the end of an nfs write, if the nfs commit fails, all the writes
will be rescheduled. They are supposed to be rescheduled as NFS_FILE_SYNC
writes, but the rpc_task structure is not completely intialized and so
the option is not passed. When the rescheduled writes complete, the
return indicates that they are NFS_UNSTABLE and we try to do another
commit. This leads to a Panic because the commit data structure pointer
was set to null in the initial (failed) commit attempt.
Signed-off-by: Terry Loftin <terry.loftin@hp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* 'for-linus' of git://git.infradead.org/users/eparis/notify:
dnotify: ignore FS_EVENT_ON_CHILD
inotify: fix coalesce duplicate events into a single event in special case
inotify: deprecate the inotify kernel interface
fsnotify: do not set group for a mark before it is on the i_list
Fix a (small) memory leak in one of the error paths of the NFS mount
options parsing code.
Regression introduced in 2.6.30 by commit a67d18f (NFS: load the
rpc/rdma transport module automatically).
Reported-by: Yinghai Lu <yinghai@kernel.org>
Reported-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a null pointer exception in pipe_rdwr_open() which
generates the stack trace:
> Unable to handle kernel NULL pointer dereference at 0000000000000028 RIP:
> [<ffffffff802899a5>] pipe_rdwr_open+0x35/0x70
> [<ffffffff8028125c>] __dentry_open+0x13c/0x230
> [<ffffffff8028143d>] do_filp_open+0x2d/0x40
> [<ffffffff802814aa>] do_sys_open+0x5a/0x100
> [<ffffffff8021faf3>] sysenter_do_call+0x1b/0x67
The failure mode is triggered by an attempt to open an anonymous
pipe via /proc/pid/fd/* as exemplified by this script:
=============================================================
while : ; do
{ echo y ; sleep 1 ; } | { while read ; do echo z$REPLY; done ; } &
PID=$!
OUT=$(ps -efl | grep 'sleep 1' | grep -v grep |
{ read PID REST ; echo $PID; } )
OUT="${OUT%% *}"
DELAY=$((RANDOM * 1000 / 32768))
usleep $((DELAY * 1000 + RANDOM % 1000 ))
echo n > /proc/$OUT/fd/1 # Trigger defect
done
=============================================================
Note that the failure window is quite small and I could only
reliably reproduce the defect by inserting a small delay
in pipe_rdwr_open(). For example:
static int
pipe_rdwr_open(struct inode *inode, struct file *filp)
{
msleep(100);
mutex_lock(&inode->i_mutex);
Although the defect was observed in pipe_rdwr_open(), I think it
makes sense to replicate the change through all the pipe_*_open()
functions.
The core of the change is to verify that inode->i_pipe has not
been released before attempting to manipulate it. If inode->i_pipe
is no longer present, return ENOENT to indicate so.
The comment about potentially using atomic_t for i_pipe->readers
and i_pipe->writers has also been removed because it is no longer
relevant in this context. The inode->i_mutex lock must be used so
that inode->i_pipe can be dealt with correctly.
Signed-off-by: Earl Chew <earl_chew@agilent.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we do rename a dir entry, like this:
rename("/tmp/ino7UrgoJ.rename1", "/tmp/ino7UrgoJ.rename2")
rename("/tmp/ino7UrgoJ.rename2", "/tmp/ino7UrgoJ")
The duplicate events should be coalesced into a single event. But those two
events do not be coalesced into a single event, due to some bad check in
event_compare(). It can not match the two NULL inodes as the same event.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
fsnotify_add_mark is supposed to add a mark to the g_list and i_list and to
set the group and inode for the mark. fsnotify_destroy_mark_by_entry uses
the fact that ->group != NULL to know if this group should be destroyed or
if it's already been done.
But fsnotify_add_mark sets the group and inode before it actually adds the
mark to the i_list and g_list. This can result in a race in inotify, it
requires 3 threads.
sys_inotify_add_watch("file") sys_inotify_add_watch("file") sys_inotify_rm_watch([a])
inotify_update_watch()
inotify_new_watch()
inotify_add_to_idr()
^--- returns wd = [a]
inotfiy_update_watch()
inotify_new_watch()
inotify_add_to_idr()
fsnotify_add_mark()
^--- returns wd = [b]
returns to userspace;
inotify_idr_find([a])
^--- gives us the pointer from task 1
fsnotify_add_mark()
^--- this is going to set the mark->group and mark->inode fields, but will
return -EEXIST because of the race with [b].
fsnotify_destroy_mark()
^--- since ->group != NULL we call back
into inotify_freeing_mark() which calls
inotify_remove_from_idr([a])
since fsnotify_add_mark() failed we call:
inotify_remove_from_idr([a]) <------WHOOPS it's not in the idr, this could
have been any entry added later!
The fix is to make sure we don't set mark->group until we are sure the mark is
on the inode and fsnotify_add_mark will return success.
Signed-off-by: Eric Paris <eparis@redhat.com>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: always pin metadata in discard mode
Btrfs: enable discard support
Btrfs: add -o discard option
Btrfs: properly wait log writers during log sync
Btrfs: fix possible ENOSPC problems with truncate
Btrfs: fix btrfs acl #ifdef checks
Btrfs: streamline tree-log btree block writeout
Btrfs: avoid tree log commit when there are no changes
Btrfs: only write one super copy during fsync
sysfs_notify_dirent is a simple atomic operation that can be used to
alert user-space that new data can be read from a sysfs attribute.
Unfortunately it cannot currently be called from non-process context
because of its use of spin_lock which is sometimes taken with
interrupts enabled.
So change all lockers of sysfs_open_dirent_lock to disable interrupts,
thus making sysfs_notify_dirent safe to be called from non-process
context (as drivers/md does in md_safemode_timeout).
sysfs_get_open_dirent is (documented as being) only called from
process context, so it uses spin_lock_irq. Other places
use spin_lock_irqsave.
The usage for sysfs_notify_dirent in md_safemode_timeout was
introduced in 2.6.28, so this patch is suitable for that and more
recent kernels.
Reported-by: Joel Andres Granados <jgranado@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As device_move() and kobject_move() both handle a NULL destination,
sysfs_move_dir() should do this as well (again) and fall back to
sysfs_root in that case.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have an optimization in btrfs to allow blocks to be
immediately freed if they were allocated in this transaction and never
written. Otherwise they are pinned and freed when the transaction
commits.
This isn't optimal for discard mode because immediately freeing
them means immediately discarding them. It is better to give the
block to the pinning code and letting the (slow) discard happen later.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The discard support code in btrfs currently is guarded by ifdefs for
BIO_RW_DISCARD, which is never defines as it's the name of an enum
memeber. Just remove the useless ifdefs to actually enable the code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Enable discard by default is not a good idea given the the trim speed
of SSD prototypes we've seen, and the carecteristics for many high-end
arrays. Turn of discards by default and require the -o discard option
to enable them on.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
A recently fsync optimization make btrfs_sync_log skip calling
wait_for_writer in the single log writer case. This is incorrect
since the writer count can also be increased by btrfs_pin_log.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
There's a problem where we don't do any space reservation for truncates, which
can cause you to OOPs because you will be allowed to go off in the weeds a bit
since we don't account for the delalloc bytes that are created as a result of
the truncate.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
xfs_dqrele_inode calls xfs_iput to release the ilock and a reference
and then also calls IRELE which does a second decrement of the reference
count. This leads to a premature freeing of inodes when quotas were turned
off while the filesystem was mounted.
Thanks to Utako Kusaka for reporting the bug and provinding a good testcase.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Utako Kusaka <u-kusaka@wm.jp.nec.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
The btrfs acl code was #ifdefing for a define
that didn't exist. This correctly matches it
to the values used by the Kconfig file.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Syncing the tree log is a 3 phase operation.
1) write and wait for all the tree log blocks for a given root.
2) write and wait for all the tree log blocks for the
tree of tree log roots.
3) write and wait for the super blocks (barriers here)
This isn't as efficient as it could be because there is
no requirement to wait for the blocks from step one to hit the disk
before we start writing the blocks from step two. This commit
changes the sequence so that we don't start waiting until
all the tree blocks from both steps one and two have been sent
to disk.
We do this by breaking up btrfs_write_wait_marked_extents into
two functions, which is trivial because it was already broken
up into two parts.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
rpm has a habit of running fdatasync when the file hasn't
changed. We already detect if a file hasn't been changed
in the current transaction but it might have been sent to
the tree-log in this transaction and not changed since
the last call to fsync.
In this case, we want to avoid a tree log sync, which includes
a number of synchronous writes and barriers. This commit
extends the existing tracking of the last transaction to change
a file to also track the last sub-transaction.
The end result is that rpm -ivh and -Uvh are roughly twice as fast,
and on par with ext3.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
During a tree-log commit for fsync, we've been writing at least
two copies of the super block and forcing them to disk.
The other filesystems write only one, and this change brings us on
par with them. A full transaction commit will write all the super
copies, so we still have redundant info written on a regular
basis.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cciss: Add cciss_allow_hpsa module parameter
cciss: Fix multiple calls to pci_release_regions
blk-settings: fix function parameter kernel-doc notation
writeback: kill space in debugfs item name
writeback: account IO throttling wait as iowait
elv_iosched_store(): fix strstrip() misuse
cfq-iosched: avoid probable slice overrun when idling
cfq-iosched: apply bool value where we return 0/1
cfq-iosched: fix think time allowed for seekers
cfq-iosched: fix the slice residual sign
cfq-iosched: abstract out the 'may this cfqq dispatch' logic
block: use proper BLK_RW_ASYNC in blk_queue_start_tag()
block: Seperate read and write statistics of in_flight requests v2
block: get rid of kblock_schedule_delayed_work()
cfq-iosched: fix possible problem with jiffies wraparound
cfq-iosched: fix issue with rq-rq merging and fifo list ordering
This avoids updating the superblock write time when we are mounting
the root file system read/only but we need to replay the journal; at
that point, for people who are east of GMT and who make their clock
tick in localtime for Windows bug-for-bug compatibility, and this will
cause e2fsck to complain and force a full file system check.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Jan Kara <jack@suse.cz>
struct sockaddr_storage * can safely be used as struct sockaddr *.
Suppress an "incompatible pointer type" warning.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An interestingly corrupted romfs file system exposed a problem with the
romfs_dev_strnlen function: it's passing the wrong value to its helpers.
Rather than limit the string to the length passed in by the callers, it
uses the size of the device as the limit.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: fix file clone ioctl for bookend extents
Btrfs: fix uninit compiler warning in cow_file_range_nocow
Btrfs: constify dentry_operations
Btrfs: optimize back reference update during btrfs_drop_snapshot
Btrfs: remove negative dentry when deleting subvolumne
Btrfs: optimize fsync for the single writer case
Btrfs: async delalloc flushing under space pressure
Btrfs: release delalloc reservations on extent item insertion
Btrfs: delay clearing EXTENT_DELALLOC for compressed extents
Btrfs: cleanup extent_clear_unlock_delalloc flags
Btrfs: fix possible softlockup in the allocator
Btrfs: fix deadlock on async thread startup
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
The file clone ioctl was incorrectly taking the offset into the
extent on disk into account when calculating the length of the
cloned extent.
The length never changes based on the offset into the physical extent.
Test case:
fallocate -l 1g image
mke2fs image
bcp image image2
e2fsck -f image2
(errors on image2)
The math bug ends up wrapping the length of the extent, and things
go wrong from there.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The extent_type variable was exposed uninit via a goto. It should be
impossible to trigger because it is protected by a check on another
variable, but this makes sure.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This patch reading level 0 tree blocks that already use full backrefs.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The use of btrfs_dentry_delete is removing dentries from the
dcache when deleting subvolumne. btrfs_dentry_delete ignores
negative dentries. This is incorrect since if we don't remove
the negative dentry, its parent dentry can't be removed.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFSv4: Kill nfs4_renewd_prepare_shutdown()
NFSv4: Fix the referral mount code
nfs: Avoid overrun when copying client IP address string
NFS: Fix port initialisation in nfs_remount()
NFS: Fix port and mountport display in /proc/self/mountinfo
NFS: Fix a default mount regression...
This patch optimizes the tree logging stuff so it doesn't always wait 1 jiffie
for new people to join the logging transaction if there is only ever 1 writer.
This helps a little bit with latency where we have something like RPM where it
will fdatasync every file it writes, and so waiting the 1 jiffie for every
fdatasync really starts to add up.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This patch moves the delalloc flushing that occurs when we are under space
pressure off to a async thread pool. This helps since we only free up
metadata space when we actually insert the extent item, which means it takes
quite a while for space to be free'ed up if we wait on all ordered extents.
However, if space is freed up due to inline extents being inserted, we can
wake people who are waiting up early, and they can finish their work.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This patch fixes an issue with the delalloc metadata space reservation
code. The problem is we used to free the reservation as soon as we
allocated the delalloc region. The problem with this is if we are not
inserting an inline extent, we don't actually insert the extent item until
after the ordered extent is written out. This patch does 3 things,
1) It moves the reservation clearing stuff into the ordered code, so when
we remove the ordered extent we remove the reservation.
2) It adds a EXTENT_DO_ACCOUNTING flag that gets passed when we clear
delalloc bits in the cases where we want to clear the metadata reservation
when we clear the delalloc extent, in the case that we do an inline extent
or we invalidate the page.
3) It adds another waitqueue to the space info so that when we start a fs
wide delalloc flush, anybody else who also hits that area will simply wait
for the flush to finish and then try to make their allocation.
This has been tested thoroughly to make sure we did not regress on
performance.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When compression is on, the cow_file_range code is farmed off to
worker threads. This allows us to do significant CPU work in parallel
on SMP machines.
But it is a delicate balance around when we clear flags and how. In
the past we cleared the delalloc flag immediately, which was safe
because the pages stayed locked.
But this is causing problems with the newest ENOSPC code, and with the
recent extent state cleanups we can now clear the delalloc bit at the
same time the uncompressed code does.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
extent_clear_unlock_delalloc has a growing set of ugly parameters
that is very difficult to read and maintain.
This switches to a flag field and well named flag defines.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Now that the VFS actually waits for the data I/O to complete before
calling into ->fsync we can stop doing it ourselves.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
This is for bug #850,
http://oss.sgi.com/bugzilla/show_bug.cgi?id=850
XFS file system segfaults , repeatedly and 100% reproducable in 2.6.30 , 2.6.31
The above only showed up on a CONFIG_XFS_DEBUG=y kernel, because
xfs_bmapi() ASSERTs that it has been asked for at least one map,
and it was getting 0.
The root cause is that our guesstimated "bufsize" from xfs_file_readdir
was fairly small, and the
bufsize -= length;
in the loop was going negative - except bufsize is a size_t, so it
was wrapping to a very large number.
Then when we did
ra_want = howmany(bufsize + mp->m_dirblksize,
mp->m_sb.sb_blocksize) - 1;
with that very large number, the (int) ra_want was coming out
negative, and a subsequent compare:
if (1 + ra_want > map_blocks ...
was coming out -true- (negative int compare w/ uint) and we went
back to xfs_bmapi() for more, even though we did not need more,
and asked for 0 maps, and hit the ASSERT.
We have kind of a type mess here, but just keeping bufsize from
going negative is probably sufficient to avoid the problem.
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
We want to always cover the log after writing out the superblock, and
in case of a synchronous writeout make sure we actually wait for the
log to be covered. That way a filesystem that has been sync()ed can
be considered clean by log recovery.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Alex Elder <aelder@sgi.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
To make sure they get properly waited on in sync when I/O is in flight and
we latter need to update the inode size. Requires a new helper to check if an
ioend structure is beyond the current EOF.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Sort out ->sync_fs to not perform a superblock writeback for the wait = 0 case
as that is just an optional first pass and the superblock will be written back
properly in the next call with wait = 1. Instead perform an opportunistic
quota writeback to have less work later. Also remove the freeze special case
as we do a proper wait = 1 call in the freeze code anyway.
Also rename the function to xfs_fs_sync_fs to match the normal naming
convention, update comments and avoid calling into the laptop_mode logic on
an error.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
We need to do a synchronous xfs_sync_fsdata to make sure the superblock
actually is on disk when we return.
Also remove SYNC_BDFLUSH flag to xfs_sync_inodes because that particular
flag is never checked.
Move xfs_filestream_flush call later to only release inodes after they
have been written out.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
This is picking up on Felix's repost of Dave's patch to implement a
.dirty_inode method. We really need this notification because
the VFS keeps writing directly into the inode structure instead
of going through methods to update this state. In addition to
the long-known atime issue we now also have a caller in VM code
that updates c/mtime that way for shared writeable mmaps. And
I found another one that no one has noticed in practice in the FIFO
code.
So implement ->dirty_inode to set i_update_core whenever the
inode gets externally dirtied, and switch the c/mtime handling to
the same scheme we already use for atime (always picking up
the value from the Linux inode).
Note that this patch also removes the xfs_synchronize_atime call
in xfs_reclaim it was superflous as we already synchronize the time
when writing the inode via the log (xfs_inode_item_format) or the
normal buffers (xfs_iflush_int).
In addition also remove the I_CLEAR check before copying the Linux
timestamps - now that we always have the Linux inode available
we can always use the timestamps in it.
Also switch to just using file_update_time for regular reads/writes -
that will get us all optimization done to it for free and make
sure we notice early when it breaks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
The unencrypted files are being measured. Update the counters to get
rid of the ecryptfs imbalance message. (http://bugzilla.redhat.com/519737)
Reported-by: Sachin Garg
Cc: Eric Paris <eparis@redhat.com>
Cc: Dustin Kirkland <kirkland@canonical.com>
Cc: James Morris <jmorris@namei.org>
Cc: David Safford <safford@watson.ibm.com>
Cc: stable@kernel.org
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
eCryptfs no longer uses a netlink interface to communicate with
ecryptfsd, so NET is not a valid dependency anymore.
MD5 is required and must be built for eCryptfs to be of any use.
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
ecryptfs uses crypto APIs so it should depend on CRYPTO.
Otherwise many build errors occur. [63 lines not pasted]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: ecryptfs-devel@lists.launchpad.net
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
The NFSv4 renew daemon is shared between all active super blocks that refer
to a particular NFS server, so it is wrong to be shutting it down in
nfs4_kill_super every time a super block is destroyed.
This patch therefore kills nfs4_renewd_prepare_shutdown altogether, and
leaves it up to nfs4_shutdown_client() to also shut down the renew daemon
by means of the existing call to nfs4_kill_renewd().
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This flag indicates a hardware detected memory corruption on the page.
Any future access of the page data may bring down the machine.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fix the following 'make includecheck' warning:
fs/proc/kcore.c: linux/mm.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a typo which causes try_location() to use the wrong length argument
when calling nfs_parse_server_name(). This again, causes the initialisation
of the mount's sockaddr structure to fail.
Also ensure that if nfs4_pathname_string() returns an error, then we pass
that error back up the stack instead of ENOENT.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
As seen in <http://bugs.debian.org/549002>, nfs4_init_client() can
overrun the source string when copying the client IP address from
nfs_parsed_mount_data::client_address to nfs_client::cl_ipaddr. Since
these are both treated as null-terminated strings elsewhere, the copy
should be done with strlcpy() not memcpy().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The recent changeset 53a0b9c4c9 (NFS: Replace
nfs_parse_ip_address() with rpc_pton()) broke nfs_remount, since the call
to rpc_pton() will zero out the port number in data->nfs_server.address.
This is actually due to a bug in nfs_remount: it should be looking at the
port number in nfs_server.port instead...
This fixes bug
http://bugzilla.kernel.org/show_bug.cgi?id=14276
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Currently, the port and mount port will both display as 65535 if you do not
specify a port number. That would be wrong...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
With the recent spate of changes, the nfs protocol version will now default
to 2 instead of 3, while the mount protocol version defaults to 3.
The following patch should ensure the defaults are consistent with the
previous defaults of vers=3,proto=tcp,mountvers=3,mountproto=tcp.
This fixes the bug
http://bugzilla.kernel.org/show_bug.cgi?id=14259
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Commit a9327cac44 added seperate read
and write statistics of in_flight requests. And exported the number
of read and write requests in progress seperately through sysfs.
But Corrado Zoccolo <czoccolo@gmail.com> reported getting strange
output from "iostat -kx 2". Global values for service time and
utilization were garbage. For interval values, utilization was always
100%, and service time is higher than normal.
So this was reverted by commit 0f78ab9899
The problem was in part_round_stats_single(), I missed the following:
if (now == part->stamp)
return;
- if (part->in_flight) {
+ if (part_in_flight(part)) {
__part_stat_add(cpu, part, time_in_queue,
part_in_flight(part) * (now - part->stamp));
__part_stat_add(cpu, part, io_ticks, (now - part->stamp));
With this chunk included, the reported regression gets fixed.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
--
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Like the cluster allocating stuff, we can lockup the box with the normal
allocation path. This happens when we
1) Start to cache a block group that is severely fragmented, but has a decent
amount of free space.
2) Start to commit a transaction
3) Have the commit try and empty out some of the delalloc inodes with extents
that are relatively large.
The inodes will not be able to make the allocations because they will ask for
allocations larger than a contiguous area in the free space cache. So we will
wait for more progress to be made on the block group, but since we're in a
commit the caching kthread won't make any more progress and it already has
enough free space that wait_block_group_cache_progress will just return. So,
if we wait and fail to make the allocation the next time around, just loop and
go to the next block group. This keeps us from getting stuck in a softlockup.
Thanks,
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The btrfs async worker threads are used for a wide variety of things,
including processing bio end_io functions. This means that when
the endio threads aren't running, the rest of the FS isn't
able to do the final processing required to clear PageWriteback.
The endio threads also try to exit as they become idle and
start more as the work piles up. The problem is that starting more
threads means kthreadd may need to allocate ram, and that allocation
may wait until the global number of writeback pages on the system is
below a certain limit.
The result of that throttling is that end IO threads wait on
kthreadd, who is waiting on IO to end, which will never happen.
This commit fixes the deadlock by handing off thread startup to a
dedicated thread. It also fixes a bug where the on-demand thread
creation was creating far too many threads because it didn't take into
account threads being started by other procs.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (41 commits)
Revert "Seperate read and write statistics of in_flight requests"
cfq-iosched: don't delay async queue if it hasn't dispatched at all
block: Topology ioctls
cfq-iosched: use assigned slice sync value, not default
cfq-iosched: rename 'desktop' sysfs entry to 'low_latency'
cfq-iosched: implement slower async initiate and queue ramp up
cfq-iosched: delay async IO dispatch, if sync IO was just done
cfq-iosched: add a knob for desktop interactiveness
Add a tracepoint for block request remapping
block: allow large discard requests
block: use normal I/O path for discard requests
swapfile: avoid NULL pointer dereference in swapon when s_bdev is NULL
fs/bio.c: move EXPORT* macros to line after function
Add missing blk_trace_remove_sysfs to be in pair with blk_trace_init_sysfs
cciss: fix build when !PROC_FS
block: Do not clamp max_hw_sectors for stacking devices
block: Set max_sectors correctly for stacking devices
cciss: cciss_host_attr_groups should be const
cciss: Dynamically allocate the drive_info_struct for each logical drive.
cciss: Add usage_count attribute to each logical drive in /sys
...
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
[PATCH] ext4: retry failed direct IO allocations
ext4: Fix build warning in ext4_dirty_inode()
ext4: drop ext4dev compat
ext4: fix a BUG_ON crash by checking that page has buffers attached to it
On a 256M filesystem, doing this in a loop:
xfs_io -F -f -d -c 'pwrite 0 64m' test
rm -f test
eventually leads to ENOSPC. (the xfs_io command does a
64m direct IO write to the file "test")
As with other block allocation callers, it looks like we need to
potentially retry the allocations on the initial ENOSPC.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This fixes the following warning:
fs/ext4/inode.c: In function 'ext4_dirty_inode':
fs/ext4/inode.c:5615: warning: unused variable 'current_handle'
We remove the jbd_debug() statement which does use current_handle, as
it's not terribly important in the grand scheme of things.
Thanks to Stephen Rothwell for pointing this out.
Signed-off-by: Curt Wohlgemuth <curtw@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: fix data space leak fix
Btrfs: remove duplicates of filemap_ helpers
Btrfs: take i_mutex before generic_write_checks
Btrfs: fix arguments to btrfs_wait_on_page_writeback_range
Btrfs: fix deadlock with free space handling and user transactions
Btrfs: fix error cases for ioctl transactions
Btrfs: Use CONFIG_BTRFS_POSIX_ACL to enable ACL code
Btrfs: introduce missing kfree
Btrfs: Fix setting umask when POSIX ACLs are not enabled
Btrfs: proper -ENOSPC handling
It's just a wrapper for <linux/fscache.h>, so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a problem where page_mkwrite can be called on a dirtied page that
already has a delalloc range associated with it. The fix is to clear any
delalloc bits for the range we are dirtying so the space accounting gets
handled properly. This is the same thing we do in the normal write case, so we
are consistent across the board. With this patch we no longer leak reserved
space.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
As mentioned in Documentation/CodingStyle, move EXPORT* macro's
to the line immediately after the closing function brace line.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Use filemap_fdatawrite_range and filemap_fdatawait_range instead of
local copies of the functions. For filemap_fdatawait_range that
also means replacing the awkward old wait_on_page_writeback_range
calling convention with the regular filemap byte offsets.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_file_write was incorrectly calling generic_write_checks without
taking i_mutex. This lead to problems with racing around i_size when
doing O_APPEND writes.
The fix here is to move i_mutex higher.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
wait_on_page_writeback_range/btrfs_wait_on_page_writeback_range takes
a pagecache offset, not a byte offset into the file. Shift the arguments
around to wait for the correct range
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Kconfig & super.c promised it'd be gone by 2.6.31, so it's
about time to drop it.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
In ext4_num_dirty_pages() we were calling page_buffers() before
checking to see if the page actually had pages attached to it; this
would cause a BUG check crash in the inline function page_buffers().
Thanks to Markus Trippelsdorf for reporting this bug.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The code to set up sctp sockets was not using the sockfd_lookup()
and sockfd_put() routines to translate an fd to a socket. The
direct fget and fput calls were resulting in error messages from
alloc_fd().
Also clean up two log messages and remove a third, related to
setting up sctp associations.
Signed-off-by: David Teigland <teigland@redhat.com>
The recently added dlm_lowcomms_connect_node() from
391fbdc5d5 does not work
when using SCTP instead of TCP. The sctp connection code
has nothing to do without data to send. Check for no data
in the sctp connection code and do nothing instead of
triggering a BUG. Also have connect_node() do nothing
when the protocol is sctp.
Signed-off-by: David Teigland <teigland@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
nilfs2: fix missing initialization of i_dir_start_lookup member
nilfs2: fix missing zero-fill initialization of btree node cache
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: Fix time encoding with extra epoch bits
ext4: Add a stub for mpage_da_data in the trace header
jbd2: Use tracepoints for history file
ext4: Use tracepoints for mb_history trace file
ext4, jbd2: Drop unneeded printks at mount and unmount time
ext4: Handle nested ext4_journal_start/stop calls without a journal
ext4: Make sure ext4_dirty_inode() updates the inode in no journal mode
ext4: Avoid updating the inode table bh twice in no journal mode
ext4: EXT4_IOC_MOVE_EXT: Check for different original and donor inodes first
ext4: async direct IO for holes and fallocate support
ext4: Use end_io callback to avoid direct I/O fallback to buffered I/O
ext4: Split uninitialized extents for direct I/O
ext4: release reserved quota when block reservation for delalloc retry
ext4: Adjust ext4_da_writepages() to write out larger contiguous chunks
ext4: Fix hueristic which avoids group preallocation for closed files
ext4: Use ext4_msg() for ext4_da_writepage() errors
ext4: Update documentation about quota mount options
* git://git.kernel.org/pub/scm/linux/kernel/git/hirofumi/fatfs-2.6:
fat: Check s_dirt in fat_sync_fs()
vfat: change the default from shortname=lower to shortname=mixed
fat/nls: Fix handling of utf8 invalid char
"Looking at ext4.h, I think the setting of extra time fields forgets to
mask the epoch bits so the epoch part overwrites nsec part. The second
change is only for coherency (2 -> EXT4_EPOCH_BITS)."
Thanks to Damien Guibouret for pointing out this problem.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The /proc/fs/jbd2/<dev>/history was maintained manually; by using
tracepoints, we can get all of the existing functionality of the /proc
file plus extra capabilities thanks to the ftrace infrastructure. We
save memory as a bonus.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The /proc/fs/ext4/<dev>/mb_history was maintained manually, and had a
number of problems: it required a largish amount of memory to be
allocated for each ext4 filesystem, and the s_mb_history_lock
introduced a CPU contention problem.
By ripping out the mb_history code and replacing it with ftrace
tracepoints, and we get more functionality: timestamps, event
filtering, the ability to correlate mballoc history with other ext4
tracepoints, etc.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
If an ioctl-initiated transaction is open, we can't force a commit during
the free space checks in order to free up pinned extents or else we
deadlock. Just ENOSPC instead.
A more satisfying solution that reserves space for the entire user
transaction up front is forthcoming...
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Fix leak of vfsmount write reference and open_ioctl_trans reference on
ENOMEM. Clean up the error paths while we're at it.
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
There are a number of kernel printk's which are printed when an ext4
filesystem is mounted and unmounted. Disable them to economize space
in the system logs. In addition, disabling the mballoc stats by
default saves a number of unneeded atomic operations for every block
allocation or deallocation.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We've already defined CONFIG_BTRFS_POSIX_ACL in Kconfig, but we're
currently not using it and are testing CONFIG_FS_POSIX_ACL instead.
CONFIG_FS_POSIX_ACL states "Never use this symbol for ifdefs".
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
We currently set sb->s_flags |= MS_POSIXACL unconditionally, which is
incorrect -- it tells the VFS that it shouldn't set umask because we
will, yet we don't set it ourselves if we aren't using POSIX ACLs, so
the umask ends up ignored.
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This patch fixes a problem with handling nested calls to
ext4_journal_start/ext4_journal_stop, when there is no journal present.
Signed-off-by: Curt Wohlgemuth <curtw@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch a problem that ext4_dirty_inode() was not calling
ext4_mark_inode_dirty() if the current_handle is not valid, which it
is the case in no journal mode.
It also removes a test for non-matching transaction which can never
happen.
Signed-off-by: Curt Wohlgemuth <curtw@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This is a cleanup of commit 91ac6f4. Since ext4_mark_inode_dirty()
has already called ext4_mark_iloc_dirty(), which in turn calls
ext4_do_update_inode(), it's not necessary to have ext4_write_inode()
call ext4_do_update_inode() in no journal mode. Indeed, it would be
duplicated work.
Reviewed-by: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The i_dir_start_lookup field in nilfs_inode_info objects should be
cleared when the objects are allocated, but the the initialization was
missing in case of reading from disk. This adds the initialization.
Since the variable just gives a start page on directory lookups, the
bug was nonfatal until now.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
This will fix file system corruption which infrequently happens after
mount. The problem was reported from users with the title "[NILFS
users] Fail to mount NILFS." (Message-ID:
<200908211918.34720.yuri@itinteg.net>), and so forth. I've also
experienced the corruption multiple times on kernel 2.6.30 and 2.6.31.
The problem turned out to be caused due to discordance between
mapping->nrpages of a btree node cache and the actual number of pages
hung on the cache; if the mapping->nrpages becomes zero even as it has
pages, truncate_inode_pages() returns without doing anything. Usually
this is harmless except it may cause page leak, but garbage collection
fairly infrequently sees a stale page remained in the btree node cache
of DAT (i.e. disk address translation file of nilfs), and induces the
corruption.
I identified a missing initialization in btree node caches was the
root cause. This corrects the bug.
I've tested this for kernel 2.6.30 and 2.6.31.
Reported-by: Yuri Chislov <yuri@itinteg.net>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: stable <stable@kernel.org>
At the start of a transaction we do a btrfs_reserve_metadata_space() and
specify how many items we plan on modifying. Then once we've done our
modifications and such, just call btrfs_unreserve_metadata_space() for
the same number of items we reserved.
For keeping track of metadata needed for data I've had to add an extent_io op
for when we merge extents. This lets us track space properly when we are doing
sequential writes, so we don't end up reserving way more metadata space than
what we need.
The only place where the metadata space accounting is not done is in the
relocation code. This is because Yan is going to be reworking that code in the
near future, so running btrfs-vol -b could still possibly result in a ENOSPC
related panic. This patch also turns off the metadata_ratio stuff in order to
allow users to more efficiently use their disk space.
This patch makes it so we track how much metadata we need for an inode's
delayed allocation extents by tracking how many extents are currently
waiting for allocation. It introduces two new callbacks for the
extent_io tree's, merge_extent_hook and split_extent_hook. These help
us keep track of when we merge delalloc extents together and split them
up. Reservations are handled prior to any actually dirty'ing occurs,
and then we unreserve after we dirty.
btrfs_unreserve_metadata_for_delalloc() will make the appropriate
unreservations as needed based on the number of reservations we
currently have and the number of extents we currently have. Doing the
reservation outside of doing any of the actual dirty'ing lets us do
things like filemap_flush() the inode to try and force delalloc to
happen, or as a last resort actually start allocation on all delalloc
inodes in the fs. This has survived dbench, fs_mark and an fsx torture
test.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Move the check to make sure the original and donor inodes are
different earlier, to avoid a potential deadlock by trying to lock the
same inode twice.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
For async direct IO that covers holes or fallocate, the end_io
callback function now queued the convertion work on workqueue but
don't flush the work rightaway as it might take too long to afford.
But when fsync is called after all the data is completed, user expects
the metadata also being updated before fsync returns.
Thus we need to flush the conversion work when fsync() is called.
This patch keep track of a listed of completed async direct io that
has a work queued on workqueue. When fsync() is called, it will go
through the list and do the conversion.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Currently the DIO VFS code passes create = 0 when writing to the
middle of file. It does this to avoid block allocation for holes, so
as not to expose stale data out when there is a parallel buffered read
(which does not hold the i_mutex lock). Direct I/O writes into holes
falls back to buffered IO for this reason.
Since preallocated extents are treated as holes when doing a
get_block() look up (buffer is not mapped), direct IO over fallocate
also falls back to buffered IO. Thus ext4 actually silently falls
back to buffered IO in above two cases, which is undesirable.
To fix this, this patch creates unitialized extents when a direct I/O
write into holes in sparse files, and registering an end_io callback which
converts the uninitialized extent to an initialized extent after the
I/O is completed.
Singed-Off-By: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
When writing into an unitialized extent via direct I/O, and the direct
I/O doesn't exactly cover the unitialized extent, split the extent
into uninitialized and initialized extents before submitting the I/O.
This avoids needing to deal with an ENOSPC error in the end_io
callback that gets used for direct I/O.
When the IO is complete, the written extent will be marked as initialized.
Singed-Off-By: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
ext4_da_reserve_space() can reserve quota blocks multiple times if
ext4_claim_free_blocks() fail and we retry the allocation. We should
release the quota reservation before restarting.
Bug found by Jan Kara.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Work around problems in the writeback code to force out writebacks in
larger chunks than just 4mb, which is just too small. This also works
around limitations in the ext4 block allocator, which can't allocate
more than 2048 blocks at a time. So we need to defeat the round-robin
characteristics of the writeback code and try to write out as many
blocks in one inode before allowing the writeback code to move on to
another inode. We add a a new per-filesystem tunable,
max_writeback_mb_bump, which caps this to a default of 128mb per
inode.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The hueristic was designed to avoid using locality group preallocation
when writing the last segment of a closed file. Fix it by move
setting size to the maximum of size and isize until after we check
whether size == isize.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
* mark struct vm_area_struct::vm_ops as const
* mark vm_ops in AGP code
But leave TTM code alone, something is fishy there with global vm_ops
being used.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows the user to see what filesystem was involved with a
particular ext4_da_writepage() error. Also, use KERN_CRIT which is
more appropriate than KERN_EMERG.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: fix locking and list handling code in cifs_open and its helper
[CIFS] Remove build warning
cifs: fix problems with last two commits
[CIFS] Fix build break when keys support turned off
cifs: eliminate cifs_init_private
cifs: convert oplock breaks to use slow_work facility (try #4)
cifs: have cifsFileInfo hold an extra inode reference
cifs: take read lock on GlobalSMBSes_lock in is_valid_oplock_break
cifs: remove cifsInodeInfo.oplockPending flag
cifs: fix oplock request handling in posix codepath
[CIFS] Re-enable Lanman security
Sometimes we only want to write pages from a specific super_block,
so allow that to be passed in.
This fixes a problem with commit 56a131dcf7
causing writeback on all super_blocks on a bdi, where we only really
want to sync a specific sb from writeback_inodes_sb().
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The patch to remove cifs_init_private introduced a locking imbalance. It
didn't remove the leftover list addition code and the unlocking in that
function. cifs_new_fileinfo does the list addition now, so there should
be no need to do it outside of that function.
pCifsInode will never be NULL, so we don't need to check for that. This
patch also gets rid of the ugly locking and unlocking across function
calls.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Steve French <sfrench@us.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
* 'writeback' of git://git.kernel.dk/linux-2.6-block:
writeback: writeback_inodes_sb() should use bdi_start_writeback()
writeback: don't delay inodes redirtied by a fast dirtier
writeback: make the super_block pinning more efficient
writeback: don't resort for a single super_block in move_expired_inodes()
writeback: move inodes from one super_block together
writeback: get rid to incorrect references to pdflush in comments
writeback: improve readability of the wb_writeback() continue/break logic
writeback: cleanup writeback_single_inode()
writeback: kupdate writeback shall not stop when more io is possible
writeback: stop background writeback when below background threshold
writeback: balance_dirty_pages() shall write more than dirtied pages
fs: Fix busyloop in wb_writeback()
Debug traces show that in per-bdi writeback, the inode under writeback
almost always get redirtied by a busy dirtier. We used to call
redirty_tail() in this case, which could delay inode for up to 30s.
This is unacceptable because it now happens so frequently for plain cp/dd,
that the accumulated delays could make writeback of big files very slow.
So let's distinguish between data redirty and metadata only redirty.
The first one is caused by a busy dirtier, while the latter one could
happen in XFS, NFS, etc. when they are doing delalloc or updating isize.
The inode being busy dirtied will now be requeued for next io, while
the inode being redirtied by fs will continue to be delayed to avoid
repeated IO.
CC: Jan Kara <jack@suse.cz>
CC: Theodore Ts'o <tytso@mit.edu>
CC: Dave Chinner <david@fromorbit.com>
CC: Chris Mason <chris.mason@oracle.com>
CC: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>