Michael L. Semon has been testing CRC patches on a 32 bit system and
been seeing assert failures in the directory code from xfs/080.
Thanks to Michael's heroic efforts with printk debugging, we found
that the problem was that the last free space being left in the
directory structure was too small to fit a unused tag structure and
it was being corrupted and attempting to log a region out of bounds.
Hence the assert failure looked something like:
.....
#5 calling xfs_dir2_data_log_unused() 36 32
#1 4092 4095 4096
#2 8182 8183 4096
XFS: Assertion failed: first <= last && last < BBTOB(bp->b_length), file: fs/xfs/xfs_trans_buf.c, line: 568
Where #1 showed the first region of the dup being logged (i.e. the
last 4 bytes of a directory buffer) and #2 shows the corrupt values
being calculated from the length of the dup entry which overflowed
the size of the buffer.
It turns out that the problem was not in the logging code, nor in
the freespace handling code. It is an initial condition bug that
only shows up on 32 bit systems. When a new buffer is initialised,
where's the freespace that is set up:
[ 172.316249] calling xfs_dir2_leaf_addname() from xfs_dir_createname()
[ 172.316346] #9 calling xfs_dir2_data_log_unused()
[ 172.316351] #1 calling xfs_trans_log_buf() 60 63 4096
[ 172.316353] #2 calling xfs_trans_log_buf() 4094 4095 4096
Note the offset of the first region being logged? It's 60 bytes into
the buffer. Once I saw that, I pretty much knew that the bug was
going to be caused by this.
Essentially, all direct entries are rounded to 8 bytes in length,
and all entries start with an 8 byte alignment. This means that we
can decode inplace as variables are naturally aligned. With the
directory data supposedly starting on a 8 byte boundary, and all
entries padded to 8 bytes, the minimum freespace in a directory
block is supposed to be 8 bytes, which is large enough to fit a
unused data entry structure (6 bytes in size). The fact we only have
4 bytes of free space indicates a directory data block alignment
problem.
And what do you know - there's an implicit hole in the directory
data block header for the CRC format, which means the header is 60
byte on 32 bit intel systems and 64 bytes on 64 bit systems. Needs
padding. And while looking at the structures, I found the same
problem in the attr leaf header. Fix them both.
Note that this only affects 32 bit systems with CRCs enabled.
Everything else is just fine. Note that CRC enabled filesystems created
before this fix on such systems will not be readable with this fix
applied.
Reported-by: Michael L. Semon <mlsemon35@gmail.com>
Debugged-by: Michael L. Semon <mlsemon35@gmail.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 8a1fd2950e)
We write the superblock every 30s or so which results in the
verifier being called. Right now that results in this output
every 30s:
XFS (vda): Version 5 superblock detected. This kernel has EXPERIMENTAL support enabled!
Use of these features in this kernel is at your own risk!
And spamming the logs.
We don't need to check for whether we support v5 superblocks or
whether there are feature bits we don't support set as these are
only relevant when we first mount the filesytem. i.e. on superblock
read. Hence for the write verification we can just skip all the
checks (and hence verbose output) altogether.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 34510185ab)
If "device is disconnected" check occurs to be true in ezusb_access_ltv(),
it just return -ENODEV. But that means request_context is leaked since
there are no any references to it anymore.
The patch adds a call to ezusb_request_context_put() before return.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CUS198 is a card based on AR9485. There are differences
between the base reference design HB125 and CUS198.
Identify such cards based on the PCI subsystem IDs and
set HW parameters appropriately.
Addresses this bug - https://bugzilla.kernel.org/show_bug.cgi?id=49201
Cc: jkp@iki.fi
Cc: gfmichaud@gmail.com
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It contains the pending fixes that were on nfc-fixes (nfc-fixes-3.10-2),
along with a few more for the pn544 and pn533 drivers, the LLCP
disconnection path and an LLCP memory leak.
Highlights for this one are:
- An initial secure element API. NFC chipsets can carry an embedded
secure element or get access to the SIM one. In both cases they
control the secure elements and this API provides a way to discover,
enable and disable the available SEs. It also exports that to
userspace in order for SE focused middleware to actually do something
with them (e.g. payments).
- NCI over SPI support. SPI is the most complex NCI specified transport
layer and we now have support for it in the kernel. The next step will
be to implement drivers for NCI chipsets using this transport like
e.g. bcm2079x.
- NFC p2p hardware simulation driver. We now have an nfcsim driver that
is mostly a loopback device between 2 NFC interfaces. It also
implements the rest of the NFC core API like polling and target
detection. This driver, with neard running on top of it, allows us to
completely test the LLCP, SNEP and Handover implementation without
physical hardware.
- A Firmware update netlink API. Most (All ?) HCI chipsets have a
special firmware update mode where applications can push a new
firmware that will be flashed. We now have a netlink API for providing
that mode to e.g. nfctool.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=/M18
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"These are the pending NFC patches for the 3.11 merge window.
It contains the pending fixes that were on nfc-fixes (nfc-fixes-3.10-2),
along with a few more for the pn544 and pn533 drivers, the LLCP
disconnection path and an LLCP memory leak.
Highlights for this one are:
- An initial secure element API. NFC chipsets can carry an embedded
secure element or get access to the SIM one. In both cases they
control the secure elements and this API provides a way to discover,
enable and disable the available SEs. It also exports that to
userspace in order for SE focused middleware to actually do something
with them (e.g. payments).
- NCI over SPI support. SPI is the most complex NCI specified transport
layer and we now have support for it in the kernel. The next step will
be to implement drivers for NCI chipsets using this transport like
e.g. bcm2079x.
- NFC p2p hardware simulation driver. We now have an nfcsim driver that
is mostly a loopback device between 2 NFC interfaces. It also
implements the rest of the NFC core API like polling and target
detection. This driver, with neard running on top of it, allows us to
completely test the LLCP, SNEP and Handover implementation without
physical hardware.
- A Firmware update netlink API. Most (All ?) HCI chipsets have a
special firmware update mode where applications can push a new
firmware that will be flashed. We now have a netlink API for providing
that mode to e.g. nfctool."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The WKS (Well Known Services) bitmask should be transmitted in big endian
order. Picky implementations will refuse to establish an LLCP link when the
WKS bit 0 is not set to 1. The vast majority of implementations out there
are not that picky though...
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to advertise our LLCP support properly and to follow the LLCP
specs requirements, we need to initialize the WKS (Well-Known Services)
bitfield to 1 as SAP 0 is the only mandatory supported service.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When we receive a RNR, the remote is busy processing the last received
frame. We set a local flag for that, and we should send a SYMM when it
is set instead of sending any pending frame.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Without the new LLCP_CONNECTING state, non blocking sockets will be
woken up with a POLLHUP right after calling connect() because their
state is stuck at LLCP_CLOSED.
That prevents userspace from implementing any proper non blocking
socket based NFC p2p client.
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver declares two virtual NFC devices supporting NFC-DEP protocol.
An LLCP connection can be established between them and all packets sent
from one device is sent back to the other, acting as loopback devices.
Once established, the LLCP link can be disconnected by disabling the target
device (with rfkill, nfctool, or neard disable-adapter test script).
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In nfc_llcp_tx_work() the sk_buff is not freed when the llcp_sock
is null and the PDU is an I one.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch keeps the socket alive and therefore does not remove
it from the sockets list in the local until the DISC PDU has been
actually sent. Otherwise we would reply with DM PDUs before sending
the DISC one.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
nfc_llcp_send_disconnect() already exists but is not used.
nfc_llcp_disconnect() naming is not consistent with other PDU
sending functions.
This patch removes nfc_llcp_send_disconnect() and renames
nfc_llcp_disconnect()
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Instead of dumping ACR122 frames as errors, we use the print_hex_dump()
dynamic debug APIs.
We also print an accurate IC version, as the ACR122 is pn532 based.
Signed-off-by: Olivier Guiter <olivier.guiter@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Enabling or disabling an NFC accessible secure element through netlink
requires giving both an NFC controller and a secure element indexes.
Once enabled the secure element will handle card emulation once polling
starts.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Called via netlink, this API will enable or disable a specific secure
element. When a secure element is enabled, it will handle card emulation
and more generically ISO-DEP target mode, i.e. all target mode cases
except for p2p target mode.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When an NFC driver or host controller stack discovers a secure element,
it will call nfc_add_se(). In order for userspace applications to use
these secure elements, a netlink event will then be sent with the SE
index and its type. With that information userspace applications can
decide wether or not to enable SEs, through their indexes.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This API will allow NFC drivers to add and remove the secure elements
they know about or detect. Typically this should be called (asynchronously
or not) from the driver or the host interface stack detect_se hook.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Secure elements need to be discovered after enabling the NFC controller.
This is typically done by the NCI core and the HCI drivers (HCI does not
specify how to discover SEs, it is left to the specific drivers).
Also, the SE enable/disable API explicitely takes a SE index as its
argument.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Supported secure elements are typically found during a discovery process
initiated when the NFC controller is up and running. For a given NFC
chipset there can be many configurations (embedded SE or not, with or
without a SIM card wired to the NFC controller SWP interface, etc...) and
thus driver code will never know before hand which SEs are available.
So we remove this field, it will be replaced by a real SE discovery
mechanism.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When using NFC-F we should copy the NFCID2 buffer that we got from
SENSF_RES through the ATR_REQ NFCID3 buffer. Not doing so violates
NFC Forum digital requirement #189.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Before any operation, driver interruption is de-asserted to prevent
race condition between TX and RX.
Transaction starts by emitting "Direct read" and acknowledged mode
bytes. Then packet length is read allowing to allocate correct NCI
socket buffer. After that payload is retrieved.
A delay after the transaction can be added.
This delay is determined by the driver during nci_spi_allocate_device()
call and can be 0.
If acknowledged mode is set:
- CRC of header and payload is checked
- if frame reception fails (CRC error): NACK is sent
- if received frame has ACK or NACK flag: unblock nci_spi_send()
Payload is passed to NCI module.
At the end, driver interruption is re asserted.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Before any operation, driver interruption is de-asserted to prevent
race condition between TX and RX.
The NCI over SPI header is added in front of NCI packet.
If acknowledged mode is set, CRC-16-CCITT is added to the packet.
Then the packet is forwarded to SPI module to be sent.
A delay after the transaction is added.
This delay is determined by the driver during nci_spi_allocate_device()
call and can be 0.
After data has been sent, driver interruption is re-asserted.
If acknowledged mode is set, nci_spi_send will block until
acknowledgment is received.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The NFC Forum defines a transport interface based on
Serial Peripheral Interface (SPI) for the NFC Controller
Interface (NCI).
This module implements the SPI transport of NCI, calling SPI module
directly to read/write data to NFC controller (NFCC).
NFCC driver should provide functions performing device open and close.
It should also provide functions asserting/de-asserting interruption
to prevent TX/RX race conditions.
NFCC driver can also fix a delay between transactions if needed by
the hardware.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pull btrfs fixes from Chris Mason:
"This is an assortment of crash fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: stop all workers before cleaning up roots
Btrfs: fix use-after-free bug during umount
Btrfs: init relocate extent_io_tree with a mapping
btrfs: Drop inode if inode root is NULL
Btrfs: don't delete fs_roots until after we cleanup the transaction
We need to clear pending interrupts on the resume
path. This brings the device into defined state
before starting the reset flow
This should solve suspend/resume issues:
mei_me : wait hw ready failed. status = 0x0
mei_me : version message write failed
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Flushing pending work items before resetting the device makes more
sense than doing so afterwards. Some of them, like e.g. the NFC
initialization one, find themselves with client IDs changed after
the reset, eventually leading to trigger a client.c:mei_me_cl_by_id()
warning after a few modprobe/rmmod cycles.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 2f94aabd9f
(refactor sctp_outq_teardown to insure proper re-initalization)
we modified sctp_outq_teardown to use sctp_outq_init to fully re-initalize the
outq structure. Steve West recently asked me why I removed the q->error = 0
initalization from sctp_outq_teardown. I did so because I was operating under
the impression that sctp_outq_init would properly initalize that value for us,
but it doesn't. sctp_outq_init operates under the assumption that the outq
struct is all 0's (as it is when called from sctp_association_init), but using
it in __sctp_outq_teardown violates that assumption. We should do a memset in
sctp_outq_init to ensure that the entire structure is in a known state there
instead.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: "West, Steve (NSN - US/Fort Worth)" <steve.west@nsn.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: netdev@vger.kernel.org
CC: davem@davemloft.net
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change the link state of VF (vPort)
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netlink directives and ndo entry to allow for controling
VF link, which can be in one of three states:
Auto - VF link state reflects the PF link state (default)
Up - VF link state is up, traffic from VF to VF works even if
the actual PF link is down
Down - VF link state is down, no traffic from/to this VF, can be of
use while configuring the VF
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fixes a race condition between concurrent initializations of netiucv devices
that try to use the same name.
sysfs: cannot create duplicate filename '/devices/iucv/netiucv2'
[...]
Call Trace:
([<00000000002edea4>] sysfs_add_one+0xb0/0xdc)
[<00000000002eecd4>] create_dir+0x80/0xfc
[<00000000002eee38>] sysfs_create_dir+0xe8/0x118
[<00000000003835a8>] kobject_add_internal+0x120/0x2d0
[<00000000003839d6>] kobject_add+0x62/0x9c
[<00000000003d9564>] device_add+0xcc/0x510
[<000003e00212c7b4>] netiucv_register_device+0xc0/0x1ec [netiucv]
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Tested-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Broadcom BCM6345 SoC Ethernet. BCM6345
has a slightly different and older DMA engine which requires the
following modifications:
- the width of the DMA channels on BCM6345 is 64 bytes vs 16 bytes,
which means that the helpers enet_dma{c,s} need to account for this
channel width and we can no longer use macros
- BCM6345 DMA engine does not have any internal SRAM for transfering
buffers
- BCM6345 buffer allocation and flow control is not per-channel but
global (done in RSET_ENETDMA)
- the DMA engine bits are right-shifted by 3 compared to other DMA
generations
- the DMA enable/interrupt masks are a little different (we need to
enabled more bits for 6345)
- some register have the same meaning but are offsetted in the ENET_DMAC
space so a lookup table is required to return the proper offset
The MAC itself is identical and requires no modifications to work.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
htb_class structures are big, and source of false sharing on SMP.
By carefully splitting them in two parts, we can improve performance.
I got 9 % performance increase on a 24 threads machine, with 200
concurrent netperf in TCP_RR mode, using a HTB hierarchy of 4 classes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Caught by sparse:
- __rcu: missing annotation to sd->flow_limit
- __user: direct access in cpumask_scnprintf
Also
- add endline character when printing bitmap if room in buffer
- avoid bucket overflow by reducing FLOW_LIMIT_HISTORY
The last item warrants some explanation. The hashtable buckets are
subject to overflow if FLOW_LIMIT_HISTORY is larger than or equal
to bucket size, since all packets may end up in a single bucket. The
current (rather arbitrary) history value of 256 happens to match the
buffer size (u8).
As a result, with a single flow, the first 128 packets are accepted
(correct), the second 128 packets dropped (correct) and then the
history[] array has filled, so that each subsequent new packet
causes an increment in the bucket for new_flow plus a decrement
for old_flow: a steady state.
This is fine if packets are dropped, as the steady state goes away
as soon as a mix of traffic reappears. But, because the 256th packet
overflowed the bucket to 0: no packets are dropped.
Instead of explicitly adding an overflow check, this patch changes
FLOW_LIMIT_HISTORY to never be able to overflow a single bucket.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
(first item)
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tulip throws an error when dma debugging is enabled, as it doesn't properly
check dma mapping results with dma_mapping_error() durring tx ring refills.
Easy fix, just add it in, and drop the frame if the mapping is bad
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Grant Grundler <grundler@parisc-linux.org>
CC: "David S. Miller" <davem@davemloft.net>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This branch contains the following bug fixes:
- Fix locking vs. interrupts. Bug caught by lockdep checks
- Fix parsing of cpp #line directive output by dtc
- Fix 'make clean' for dtc temporary files.
There is also a commit that regenerates the dtc lexer and parser files
with Bison 2.5. The only purpose of this commit is to separate the
functional change in the dtc bug fix from the code generation change
caused by a different Bison version.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=om+W
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree bug fixes from Grant Likely:
"This branch contains the following bug fixes:
- Fix locking vs. interrupts. Bug caught by lockdep checks
- Fix parsing of cpp #line directive output by dtc
- Fix 'make clean' for dtc temporary files.
There is also a commit that regenerates the dtc lexer and parser files
with Bison 2.5. The only purpose of this commit is to separate the
functional change in the dtc bug fix from the code generation change
caused by a different Bison version"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
dtc: ensure #line directives don't consume data from the next line
dtc: Update generated files to output from Bison 2.5
of: Fix locking vs. interrupts
kbuild: make sure we clean up DTB temporary files
This is a simple forward to the HCI driver. When driver is done with the
operation, it shall directly notify NFC Core by calling
nfc_fw_upload_done().
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As several NFC chipsets can have their firmwares upgraded and
reflashed, this patchset adds a new netlink command to trigger
that the driver loads or flashes a new firmware. This will allows
userspace triggered firmware upgrade through netlink.
The firmware name or hint is passed as a parameter, and the driver
will eventually fetch the firmware binary through the request_firmware
API.
The cmd can only be executed when the nfc dev is not in use. Actual
firmware loading/flashing is an asynchronous operation. Result of the
operation shall send a new event up to user space through the nfc dev
multicast socket. During operation, the nfc dev is not openable and
thus not usable.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
skb->dev is used for carrying a net_device pointer and not
an nci_dev pointer.
Remove usage of skb-dev to carry nci_dev and replace it by parameter
in nci_recv_frame(), nci_send_frame() and driver send() functions.
NfcWilink driver is also updated to use those functions.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix to return -ENOMEM in the nfc device alloc error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There is no builtin command for driver to check the presence of
Felica and Jewel device, it is more reasonable for the userspace
daemon neard to build seperate commands to check the presence of
the card.
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFCID2 is defined as the first 2 manufacturer ID (IDm) bytes.
NFC DEP (NFC peer to peer) devices Type-F NFCID2 must start with
0x01fe according to the NFC Digital Specification.
By checking those first 2 bytes we send the right command either to the
reader gate when NFCID2 != 0x1fe (The NFC tag case) or to the NFCIP1 gate
when seeing an NFC DEP device (The NFC peer to peer case).
Without this fix, Felica (Type F) tags are not properly detected with this
driver.
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Previously, the #line parsing regex ended with ({WS}+[0-9]+)?. The {WS}
could match line-break characters. If the #line directive did not contain
the optional flags field at the end, this could cause any integer data on
the next line to be consumed as part of the #line directive parsing. This
could cause syntax errors (i.e. #line parsing consuming the leading 0
from a hex literal 0x1234, leaving x1234 to be parsed as cell data,
which is a syntax error), or invalid compilation results (i.e. simply
consuming literal 1234 as part of the #line processing, thus removing it
from the cell data).
Fix this by replacing {WS} with [ \t] so that it can't match line-breaks.
Convert all instances of {WS}, even though the other instances should be
irrelevant for any well-formed #line directive. This is done for
consistency and ultimate safety.
[Cherry picked from DTC commit a1ee6f068e1c8dbc62873645037a353d7852d5cc]
Reported-by: Ian Campbell <Ian.Campbell@citrix.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch merely updates the generated dtc parser and lexer files to
the output generated by Bison 2.5. The previous versions were generated
from version 2.4.1. The only reason for this commit is to minimize the
diff on the next commit which fixes a bug in the DTC #line directive
parsing. Otherwise the Bison changes would be intermingled with the
functional changes.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
