This beats the heuristic that the connector is involved in what format
should be output for cases where this fails.
E.g. if there is a bridge that changes format between the encoder and the
connector, or if some of the RGB pins between the lcd controller and the
encoder are not routed on the PCB.
This is critical for the devices that have the "conflicting output
formats" issue (SAM9N12, SAM9X5, SAMA5D3), since the most significant
RGB bits move around depending on the selected output mode. For
devices that do not have the "conflicting output formats" issue
(SAMA5D2, SAMA5D4), this is completely irrelevant.
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180825085620.10566-5-peda@axentia.se
This enables more flexible devicetrees. You can e.g. have two output
nodes where one is not enabled, without the ordering affecting things.
Prior to this patch the active nodes had to have endpoint id zero and
upwards consecutively.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180825085620.10566-4-peda@axentia.se
But only if the highest pixel-clock frequency lower than requested
is significantly less accurate than the lowest frequency higher than
requested.
I pulled "10 times" as the discriminator out of the hat, and went with
that.
This is useful, if e.g. the target pixel-clock is 65MHz and the sys_clk
is 132MHz. In this case the highest possible pixel-clock lower than the
requested 65MHz is 52.8MHz, which is almost 20% off (and outside the
spec for the panel). The lowest possible pixel-clock higher than 65MHz
is 66MHz, which is a *much* better match, and only 1.5% off.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180824092458.13165-3-peda@axentia.se
If the divider used to get the pixel-clock is small, the granularity
of the frequencies possible for the pixel-clock is quite coarse. E.g.
requesting a pixel-clock of 65MHz with a sys_clk of 132MHz results
in the divider being set to 3 ending up with 44MHz.
By preferring the doubled sys_clk as base, the divider instead ends
up as 5 yielding a pixel-clock of 52.8Mhz, which is a definite
improvement.
While at it, clamp the divider so that it does not overflow in case
it gets big.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180824092458.13165-2-peda@axentia.se
A new helper function(__drm_atomic_helper_plane_reset) has been added
for linking a plane with its state and resetting the core
properties(alpha, rotation, etc.) to their default values.
Use that instead of duplicating the logic.
__drm_atomic_helper_plane_reset initializes the alpha property to its
max value, which is defined by the drm core as DRM_BLEND_ALPHA_OPAQUE,
so nothing changes regarding the alpha value.
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180804161530.12275-5-alexandru-cosmin.gheorghe@arm.com
- A reversion of a commit in drm/sun4i to fix a run-time fault.
- Various fixes to the sii8620 bridge.
- Small bugfix to correctly check stride in atmel-hlcdc.
-----BEGIN PGP SIGNATURE-----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=ngPr
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2018-06-21' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Fixes for v4.18-rc2:
- A reversion of a commit in drm/sun4i to fix a run-time fault.
- Various fixes to the sii8620 bridge.
- Small bugfix to correctly check stride in atmel-hlcdc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/787d4bef-a579-4046-d0fc-f8c2c5b80c25@linux.intel.com
The statement always evaluates to true since the struct fields
are arrays. This has shown up as a warning when compiling with
clang:
warning: address of array 'desc->layout.xstride' will always
evaluate to 'true' [-Wpointer-bool-conversion]
Check for values in the first plane instead.
Fixes: 1a396789f6 ("drm: add Atmel HLCDC Display Controller support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180617084826.31885-1-stefan@agner.ch
We want to get rid of plane->fb on atomic drivers. Stop looking at it.
Daniel pointed out that the drm_framebuffer_put() in the plane cleanup
indicates that the driver doesn't shut things down cleanly. To do
that we should be able to just call drm_atomic_helper_shutdown(). Not
really sure the current cleanup sequence is actually sane, but whatever.
v2: Replace the drm_framebuffer_put() with
drm_atomic_helper_shutdown() (Daniel)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405151400.11326-10-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use drm_fb_cma_fbdev_init() and drm_fb_cma_fbdev_fini() which relies on
the fact that drm_device holds a pointer to the drm_fb_helper structure.
This means that the driver doesn't have to keep track of that.
Also use the drm_fb_helper functions directly.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171115142001.45358-6-noralf@tronnes.org
-----BEGIN PGP SIGNATURE-----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=xVV2
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.15.
Core:
- Atomic object lifetime fixes
- Atomic iterator improvements
- Sparse/smatch fixes
- Legacy kms ioctls to be interruptible
- EDID override improvements
- fb/gem helper cleanups
- Simple outreachy patches
- Documentation improvements
- Fix dma-buf rcu races
- DRM mode object leasing for improving VR use cases.
- vgaarb improvements for non-x86 platforms.
New driver:
- tve200: Faraday Technology TVE200 block.
This "TV Encoder" encodes a ITU-T BT.656 stream and can be found in
the StorLink SL3516 (later Cortina Systems CS3516) as well as the
Grain Media GM8180.
New bridges:
- SiI9234 support
New panels:
- S6E63J0X03, OTM8009A, Seiko 43WVF1G, 7" rpi touch panel, Toshiba
LT089AC19000, Innolux AT043TN24
i915:
- Remove Coffeelake from alpha support
- Cannonlake workarounds
- Infoframe refactoring for DisplayPort
- VBT updates
- DisplayPort vswing/emph/buffer translation refactoring
- CCS fixes
- Restore GPU clock boost on missed vblanks
- Scatter list updates for userptr allocations
- Gen9+ transition watermarks
- Display IPC (Isochronous Priority Control)
- Private PAT management
- GVT: improved error handling and pci config sanitizing
- Execlist refactoring
- Transparent Huge Page support
- User defined priorities support
- HuC/GuC firmware refactoring
- DP MST fixes
- eDP power sequencing fixes
- Use RCU instead of stop_machine
- PSR state tracking support
- Eviction fixes
- BDW DP aux channel timeout fixes
- LSPCON fixes
- Cannonlake PLL fixes
amdgpu:
- Per VM BO support
- Powerplay cleanups
- CI powerplay support
- PASID mgr for kfd
- SR-IOV fixes
- initial GPU reset for vega10
- Prime mmap support
- TTM updates
- Clock query interface for Raven
- Fence to handle ioctl
- UVD encode ring support on Polaris
- Transparent huge page DMA support
- Compute LRU pipe tweaks
- BO flag to allow buffers to opt out of implicit sync
- CTX priority setting API
- VRAM lost infrastructure plumbing
qxl:
- fix flicker since atomic rework
amdkfd:
- Further improvements from internal AMD tree
- Usermode events
- Drop radeon support
nouveau:
- Pascal temperature sensor support
- Improved BAR2 handling
- MMU rework to support Pascal MMU
exynos:
- Improved HDMI/mixer support
- HDMI audio interface support
tegra:
- Prep work for tegra186
- Cleanup/fixes
msm:
- Preemption support for a5xx
- Display fixes for 8x96 (snapdragon 820)
- Async cursor plane fixes
- FW loading rework
- GPU debugging improvements
vc4:
- Prep for DSI panels
- fix T-format tiling scanout
- New madvise ioctl
Rockchip:
- LVDS support
omapdrm:
- omap4 HDMI CEC support
etnaviv:
- GPU performance counters groundwork
sun4i:
- refactor driver load + TCON backend
- HDMI improvements
- A31 support
- Misc fixes
udl:
- Probe/EDID read fixes.
tilcdc:
- Misc fixes.
pl111:
- Support more variants
adv7511:
- Improve EDID handling.
- HDMI CEC support
sii8620:
- Add remote control support"
* tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux: (1480 commits)
drm/rockchip: analogix_dp: Use mutex rather than spinlock
drm/mode_object: fix documentation for object lookups.
drm/i915: Reorder context-close to avoid calling i915_vma_close() under RCU
drm/i915: Move init_clock_gating() back to where it was
drm/i915: Prune the reservation shared fence array
drm/i915: Idle the GPU before shinking everything
drm/i915: Lock llist_del_first() vs llist_del_all()
drm/i915: Calculate ironlake intermediate watermarks correctly, v2.
drm/i915: Disable lazy PPGTT page table optimization for vGPU
drm/i915/execlists: Remove the priority "optimisation"
drm/i915: Filter out spurious execlists context-switch interrupts
drm/amdgpu: use irq-safe lock for kiq->ring_lock
drm/amdgpu: bypass lru touch for KIQ ring submission
drm/amdgpu: Potential uninitialized variable in amdgpu_vm_update_directories()
drm/amdgpu: potential uninitialized variable in amdgpu_vce_ring_parse_cs()
drm/amd/powerplay: initialize a variable before using it
drm/amd/powerplay: suppress KASAN out of bounds warning in vega10_populate_all_memory_levels
drm/amd/amdgpu: fix evicted VRAM bo adjudgement condition
drm/vblank: Tune drm_crtc_accurate_vblank_count() WARN down to a debug
drm/rockchip: add CONFIG_OF dependency for lvds
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's dead code because this is now handled in the core.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Eric Engestrom <eric@engestrom.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Sushmita Susheelendra <ssusheel@codeaurora.org>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: intel-gfx@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-5-daniel.vetter@ffwll.ch
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Acked-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
drm_*_reference() and drm_*_unreference() functions are just
compatibility alias for drm_*_get() and drm_*_put() and should not be
used by new code. So convert all users of compatibility functions to use
the new APIs.
Signed-off-by: Cihangir Akturk <cakturk@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1501761585-11757-6-git-send-email-cakturk@gmail.com
drm_plane_helper_funcs and drm_plane_funcsare not supposed to change
at runtime. All functions working with drm_plane_helper_funcs and
drm_plane_funcs work with const. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6072 596 0 6668 1a0c atmel_hlcdc_plane.o
File size After adding 'const':
text data bss dec hex filename
6218 436 0 6654 19fe atmel_hlcdc_plane.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/646415a3b2e62182f85254115e8491e5caf4b2c7.1499098826.git.arvind.yadav.cs@gmail.com
This is the plumbing for supporting fb modifiers on planes. Modifiers
have already been introduced to some extent, but this series will extend
this to allow querying modifiers per plane. Based on this, the client to
enable optimal modifications for framebuffers.
This patch simply allows the DRM drivers to initialize their list of
supported modifiers upon initializing the plane.
v2: A minor addition from Daniel
v3:
* Updated commit message
* s/INVALID/DRM_FORMAT_MOD_INVALID (Liviu)
* Remove some excess newlines (Liviu)
* Update comment for > 64 modifiers (Liviu)
v4: Minor comment adjustments (Liviu)
v5: Some new platforms added due to rebase
v6: Add some missed plane inits (or maybe they're new - who knows at
this point) (Daniel)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Daniel Stone <daniels@collabora.com> (v2)
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Stone <daniels@collabora.com>
drm_atomic_helper_swap_state() will be changed to interruptible waiting
in the next few commits, so all drivers have to be changed to handling
failure.
Atmel tracks pending commits through dc->commit.pending, so it can
ignore the changes by setting stall = false. We never return failure in
this case, so make failure a BUG_ON.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170711143314.2148-5-maarten.lankhorst@linux.intel.com
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
for_each_obj_in_state is about to be removed, so use the new iterator
macros.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170712081344.25495-9-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The CRTC .disable() helper operation is deprecated for atomic drivers,
the new .atomic_disable() helper operation being preferred. Convert all
atomic drivers to .atomic_disable() to avoid cargo-cult use of
.disable() in new drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # for sun4i
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> # for mediatek
Acked-by: Alexey Brodkin <abrodkin@synopsys.com> # for arcpgu
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # for atmel-hlcdc
Tested-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Vincent Abriou <vincent.abriou@st.com> # for sti
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> # for vmwgfx
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630093646.7928-3-laurent.pinchart+renesas@ideasonboard.com
The old state is useful for drivers that need to perform operations at
enable time that depend on the transition between the old and new
states.
While at it, rename the operation to .atomic_enable() to be consistent
with .atomic_disable(), as the .enable() operation is used by atomic
helpers only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # for sun4i
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> # for imx-drm and mediatek
Acked-by: Alexey Brodkin <abrodkin@synopsys.com> # for arcpgu
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # for atmel-hlcdc
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> # for hdlcd and mali-dp
Acked-by: Stefan Agner <stefan@agner.ch> # for fsl-dcu
Tested-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Vincent Abriou <vincent.abriou@st.com> # for sti
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> # for vmwgfx
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630093646.7928-2-laurent.pinchart+renesas@ideasonboard.com
All layers of all supported chips support this, the only variable is the
base address of the lookup table in the register map.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1498107791-17450-3-git-send-email-peda@axentia.se
drm_fbdev_cma_hotplug_event() already checks for NULL pointers before
dereferencing, so callers don't need to do that.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170329144401.1804-11-thierry.reding@gmail.com
Core Changes:
- Stop proliferation of drm_vblank_cleanup by adding to the docs and deleting
boilerplate (Daniel)
- Roll out and use mode_valid hooks across crtc/encoder/bridge (Jose)
- Add drm_vblank.[hc] to isolate vblank code from optional irq helpers (Daniel)
Driver Changes:
- Replace drm_for_each_connector with drm_for_each_connector_iter (Gustavo)
- A couple misc driver fixes
Cc: Gustavo Padovan <gustavo.padovan@collabora.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
* tag 'drm-misc-next-2017-06-02' of git://anongit.freedesktop.org/git/drm-misc: (34 commits)
drm/vc4: Mark the device as active when enabling runtime PM.
drm: remove writeq/readq function definitions
drm/atmel-hlcdc: Use crtc->mode_valid() callback
drm/exynos: Drop drm_vblank_cleanup
drm/hdlcd|mali: Drop drm_vblank_cleanup
drm/doc: Polish irq helper documentation
drm: Extract drm_vblank.[hc]
drm/vc4: Fix comment in vc4_drv.h
drm/pl111: fix warnings without CONFIG_ARM_AMBA
drm/atomic: Consitfy mode parameter to drm_atomic_set_mode_for_crtc()
drm/arcgpu: Drop drm_vblank_cleanup
drm/atmel: Drop drm_vblank_cleanup
drm/imx: Drop drm_vblank_cleanup
drm/meson: Drop drm_vblank_cleanup
drm/stm: Drop drm_vblank_cleanup
drm/sun4i: Drop drm_vblank_cleanup
drm: better document how to send out the crtc disable event
drm: Use vsnprintf extension %ph
drm/doc: move printf helpers out of drmP.h
drm/pl111: select DRM_PANEL
...
This cuts 135 lines of boilerplate, at the cost of losing the
filtering of get_modes() using atmel_hlcdc_dc_mode_valid(). The
atomic check will still check that we don't set an invalid mode,
though.
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511183128.25085-7-eric@anholt.net
Now that we have a callback to check if crtc supports a given mode
we can use it in atmel-hlcdc so that we restrict the number of probbed
modes to the ones we can actually display.
Also, remove the mode_fixup() callback as this is no longer needed
because mode_valid() will be called before.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/95fd6c06c58bd0b957e36a8d7068e6a74b581304.1495720737.git.joabreu@synopsys.com
Again almost correct, but since interrupts are shut down after vblank
still a race. Proper cleanup would call drm_atomic_helper_shutdown to
make sure this really is safe.
v2: Remove misplace malidp hunk (Liviu).
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170524145212.27837-18-daniel.vetter@ffwll.ch
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZK2lrAAoJEHm+PkMAQRiGm3AH/13F1DlIk05aSXHoDr/idIpR
GMHmk3YF+EuFjsL463Sh6s/SSWmz0Lda8euaoB4wCWvQFX2ZjTE+aOd79XlRiZJQ
OTtLkV9I41eXIJUpEOHia7xZiCsbw+usqcHrm1aBoSh5KKV2iQmEOrnJdibqJVOF
eXUMphNK/zFtAd2bKtQSxkaBnOOqsQUgVQSkr2K9rSg25l0KokFC6c5K5IjLn4x9
QgDY4wmMvHrDz0CtpoqlNM4XqbsDJVrFeZGfg6hlMqSRDeXeg4h3Ol0VfIT496RP
QBdrDb6hWO+HKt9B0M+7Q+8a/Fsw+5dtpqv1W/Wlr0i4CS6euU8NChAmrpkrqGo=
=m5ba
-----END PGP SIGNATURE-----
Backmerge tag 'v4.12-rc3' into drm-next
Linux 4.12-rc3
Daniel has requested this for some drm-intel-next work.
Add DRM_MODE_ROTATE_ and DRM_MODE_REFLECT_ defines to the UAPI
as a convenience.
Ideally the DRM_ROTATE_ and DRM_REFLECT_ property ids are looked up
through the atomic API, but realizing that userspace is likely to take
shortcuts and assume that the enum values are what is sent over the
wire.
As a result these defines are provided purely as a convenience to
userspace applications.
Changes since v3:
- Switched away from past tense in comments
- Add define name change to previously mis-spelled DRM_REFLECT_X comment
- Improved the comment for the DRM_MODE_REFLECT_<axis> comment
Changes since v2:
- Changed define prefix from DRM_MODE_PROP_ to DRM_MODE_
- Fix compilation errors
- Changed comment formatting
- Deduplicated comment lines
- Clarified DRM_MODE_PROP_REFLECT_ comment
Changes since v1:
- Moved defines from drm.h to drm_mode.h
- Changed define prefix from DRM_ to DRM_MODE_PROP_
- Updated uses of the defines to the new prefix
- Removed include from drm_rect.c
- Stopped using the BIT() macro
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170519205017.23307-2-robert.foss@collabora.com
drm_of_find_panel_or_bridge() is expecting np to point to the encoder
node, not the bridge or panel this encoder is feeding.
Moreover, the endpoint parameter passed to drm_of_find_panel_or_bridge()
is always set to zero, which prevents us from probing all outputs.
We also move the atmel_hlcdc_rgb_output allocation after the
panel/bridge detection to avoid useless allocations.
Reported-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fixes: ebc9446135 ("drm: convert drivers to use drm_of_find_panel_or_bridge")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1495110921-4032-1-git-send-email-boris.brezillon@free-electrons.com
It's not possible for endpoint to be zero so the test doesn't work. If
we break on the first iteration through the loop then endpoint is 1 and
"ret" is uninitialized.
Fixes: ebc9446135 ("drm: convert drivers to use drm_of_find_panel_or_bridge")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170415192142.GA6416@mwanda
Similar to the previous commit, convert drivers open coding OF graph
parsing to use drm_of_find_panel_or_bridge instead.
This changes some error messages to debug messages (in the graph core).
Graph connections are often "no connects" depending on the particular
board, so we want to avoid spurious messages. Plus the kernel is not a
DT validator.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[seanpaul dropped rockchip changes since they're now obsolete]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
The current suspend resume implementation is assuming register values are
kept when entering suspend, which is no longer the case with the
suspend-to-RAM on the sama5d2.
While at it, switch to the generic infrastructure to enter suspend mode
(drm_atomic_helper_suspend/resume()).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1488371461-22243-1-git-send-email-boris.brezillon@free-electrons.com
Less code ftw.
This converts all drivers except the tinydrm helper module. That one
needs more work, since it gets the THIS_MODULE reference from
tinydrm.ko instead of the actual driver module like it should.
Probably needs a similar trick like I used here with generating the
entire struct with a macro.
Cc: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308141257.12119-24-daniel.vetter@ffwll.ch
An HLCDC layers in Atmel's nomenclature is either a DRM plane or a 'Post
Processing Layer' which can be used to output the results of the HLCDC
composition in a memory buffer.
atmel_hlcdc_layer.c was designed to be generic enough to be re-usable in
both cases, but we're not exposing the post-processing layer yet, and
even if we were, I'm not sure the code would provide the necessary tools
to manipulate this kind of layer.
Moreover, the code in atmel_hlcdc_{plane,layer}.c was designed before the
atomic modesetting API, and was trying solve the
check-setting/commit-if-ok/rollback-otherwise problem, which is now
entirely solved by the existing core infrastructure.
And finally, the code in atmel_hlcdc_layer.c is over-complicated compared
to what we really need. This rework is a good excuse to simplify it. Note
that this rework solves an existing resource leak (leading to a -EBUSY
error) which I failed to clearly identify.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Despite the documentation claim that cleanup_fb will match prior calls
to prepare_fb, in case of NULL framebuffers in the transitional helpers,
the code will skip the call to prepare_fb but not the corresponding
cleanup_fb call. This asymmetry in semantics is unnecessarily surprising
for developers transitioning drivers to atomic model, specially because
the final atomic handlers don't have the issue - the prepare_fb is
always called, despite the new state framebuffer being null.
The only current user of the transitional helper that doesn't take care
of null framebuffers explicitly inside the prepare_fb hook is
atmel_hlcdc, so we take special care to make sure we don't break
anything there.
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170216164442.28704-1-krisman@collabora.co.uk
The vblank hooks in struct drm_driver are deprecated and only meant for
legacy drivers. For modern drivers with DRIVER_MODESET flag, the hooks
in struct drm_crtc_funcs should be used instead.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1486458995-31018-8-git-send-email-shawnguo@kernel.org
Core code already makes drm_driver.get_vblank_counter hook optional by
letting drm_vblank_no_hw_counter be the default implementation for the
function hook. So the drm_vblank_no_hw_counter assignment in the driver
code becomes redundant and can be removed now.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1486458995-31018-3-git-send-email-shawnguo@kernel.org
Instead of receiving the num_crts as a parameter, we can read it
directly from the mode_config structure. I audited the drivers that
invoke this helper and I believe all of them initialize the mode_config
struct accordingly, prior to calling the fb_helper.
I used the following coccinelle hack to make this transformation, except
for the function headers and comment updates. The first and second
rules are split because I couldn't find a way to remove the unused
temporary variables at the same time I removed the parameter.
// <smpl>
@r@
expression A,B,D,E;
identifier C;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)
@@
expression A,B,C,D,E;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)
@@
identifier r.C;
type T;
expression V;
@@
- T C;
<...
when != C
- C = V;
...>
// </smpl>
Changes since v1:
- Rebased on top of the tip of drm-misc-next.
- Remove mention to sti since a proper fix got merged.
Suggested-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170202162640.27261-1-krisman@collabora.co.uk
time instead of waiting for the connector status change.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JDc1
-----END PGP SIGNATURE-----
Merge tag 'drm/atmel-hlcdc/for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/bbrezillon/linux into drm-next
Contains a single patch to create the fbdev at driver's registration
time instead of waiting for the connector status change.
* tag 'drm/atmel-hlcdc/for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/bbrezillon/linux:
drm/atmel-hlcdc: Rework the fbdev creation logic
