Due to the cross dependencies between hwmod for automanaged device
information for OMAP and dts node definitions, we can run into scenarios
where the dts node is defined, however it's hwmod entry is yet to be
added. In these cases:
a) omap_device does not register a pm_domain (since it cannot find
hwmod entry).
b) driver does not know about (a), does a pm_runtime_get_sync which
never fails
c) It then tries to do some operation on the device (such as read the
revision register (as part of probe) without clock or adequate OMAP
generic PM operation performed for enabling the module.
This causes a crash such as that reported in:
https://bugzilla.kernel.org/show_bug.cgi?id=66441
When 'ti,hwmod' is provided in dt node, it is expected that the device
will not function without the OMAP's power automanagement. Hence, when
we hit a fail condition (due to hwmod entries not present or other
similar scenario), fail at pm_domain level due to lack of data, provide
enough information for it to be fixed, however, it allows for the driver
to take appropriate measures to prevent crash.
Reported-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Fix a few hwmod code problems involving recovery with bad data and bad
IP block OCP reset handling. Also, fix the hwmod data to enable IP
block OCP reset for the OMAP USBHOST devices on OMAP3+.
Basic build, boot, and PM tests are available here:
http://www.pwsan.com/omap/testlogs/prcm_fixes_a_v3.13-rc/20131209030611/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=mDB2
-----END PGP SIGNATURE-----
Merge tag 'for-v3.13-rc/hwmod-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
From Paul Walmsley:
ARM: OMAP2+: hwmod code/data: fixes for v3.13-rc
Fix a few hwmod code problems involving recovery with bad data and bad
IP block OCP reset handling. Also, fix the hwmod data to enable IP
block OCP reset for the OMAP USBHOST devices on OMAP3+.
Basic build, boot, and PM tests are available here:
http://www.pwsan.com/omap/testlogs/prcm_fixes_a_v3.13-rc/20131209030611/
* tag 'for-v3.13-rc/hwmod-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP2+: hwmod: Fix usage of invalid iclk / oclk when clock node is not present
ARM: OMAP3: hwmod data: Don't prevent RESET of USB Host module
ARM: OMAP2+: hwmod: Fix SOFTRESET logic
ARM: OMAP4+: hwmod data: Don't prevent RESET of USB Host module
Signed-off-by: Kevin Hilman <khilman@linaro.org>
commit dc75925d(OMAP: hwmod: Fix the missing braces) introduced
missing braces, however, we just set return result if clk_get fail
and we populate the error pointer in clk pointer and pass it along to
clk_prepare. This is wrong. The intent seems to be retry remaining
clocks if they are available and warn the ones we cant find clks for.
With the current logic, we see the following crash:
omap_hwmod: l3_main: cannot clk_get interface_clk emac_ick
Unable to handle kernel NULL pointer dereference at virtual address 00000032
pgd = c0004000
[00000032] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.13.0-rc1-00044-gcc9fd5a-dirty #19
task: ce0c3440 ti: ce0c4000 task.ti: ce0c4000
PC is at __clk_prepare+0x10/0x74
LR is at clk_prepare+0x14/0x24
<snip>
[<c044d59c>] (__clk_prepare+0x10/0x74) from [<c044d9b0>] (clk_prepare+0x14/0x24)
[<c044d9b0>] (clk_prepare+0x14/0x24) from [<c077d8c4>] (_init+0x24c/0x3bc)
[<c077d8c4>] (_init+0x24c/0x3bc) from [<c0027328>] (omap_hwmod_for_each+0x34/0x5c)
[<c0027328>] (omap_hwmod_for_each+0x34/0x5c) from [<c077dfa0>] (__omap_hwmod_setup_all+0x24/0x40)
[<c077dfa0>] (__omap_hwmod_setup_all+0x24/0x40) from [<c0008928>] (do_one_initcall+0x38/0x168)
[<c0008928>] (do_one_initcall+0x38/0x168) from [<c0771be8>] (kernel_init_freeable+0xfc/0x1cc)
[<c0771be8>] (kernel_init_freeable+0xfc/0x1cc) from [<c0521064>] (kernel_init+0x8/0x110)
[<c0521064>] (kernel_init+0x8/0x110) from [<c000e568>] (ret_from_fork+0x14/0x2c)
Code: e92d4038 e2504000 01a05004 0a000005 (e5943034)
So, just warn and continue instead of proceeding and crashing, with
missing clock nodes/bad data, we will eventually fail, however we
should now have enough information to identify the culprit.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Unlike what the comment states, errata i660 does not state that we
can't RESET the USB host module. Instead it states that RESET is the
only way to recover from a deadlock situation.
RESET ensures that the module is in a known good state irrespective
of what bootloader does with the module, so it must be done at boot.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> # Panda, BeagleXM
Fixes: de231388cb ("ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3")
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In _ocp_softreset(), after _set_softreset() + write_sysconfig(),
the hwmod's sysc_cache will always contain SOFTRESET bit set
so all further writes to sysconfig using this cache will initiate
a repeated SOFTRESET e.g. enable_sysc(). This is true for OMAP3 like
platforms that have RESET_DONE status in the SYSSTATUS register and
so the the SOFTRESET bit in SYSCONFIG is not automatically cleared.
It is not a problem for OMAP4 like platforms that indicate RESET
completion by clearing the SOFTRESET bit in the SYSCONFIG register.
This repeated SOFTRESET is undesired and was the root cause of
USB host issues on OMAP3 platforms when hwmod was allowed to do the
SOFTRESET for the USB Host module.
To fix this we clear the SOFTRESET bit and update the sysconfig
register + sysc_cache using write_sysconfig().
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> # Panda, BeagleXM
[paul@pwsan.com: renamed _clr_softreset() to _clear_softreset()]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Without this, the USB devices are sometimes not detected on OMAP4 Panda
with u-boot v2013.10.
Unlike what the comment states, errata i660 does not state that we
can't RESET the USB host module. Instead it states that RESET is the
only way to recover from a deadlock situation.
RESET ensures that the module is in a known good state irrespective
of what bootloader does with the module, so it must be done at boot.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> # Panda, BeagleXM
Acked-by: Benoît Cousson <bcousson@baylibre.com>
Fixes: af88fa9aa7 ("ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4")
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The am3517 is wrongly booting as omap3 which means that the am3517
specific devices like Ethernet won't work when booted with device
tree. Now with the new devices defined in am3517.dtsi, let's use
that instead of the omap3.dtsi, and add a separate machine entry
for am3517 so am3517-evm can use it.
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated comments and fixed build without omap3]
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have some device tree properties where the ti,hwmod have multiple
values:
am33xx.dtsi: ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
am4372.dtsi: ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
dra7.dtsi: ti,hwmods = "l3_main_1", "l3_main_2";
omap3.dtsi: ti,hwmods = "mcbsp2", "mcbsp2_sidetone";
omap3.dtsi: ti,hwmods = "mcbsp3", "mcbsp3_sidetone";
omap4.dtsi: ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
omap5.dtsi: ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
That's not correct way of doing things in this case because these are
separate devices with their own address space, interrupts, SYSCONFIG
registers and can set their PM states independently.
So they should all be fixed up to be separate devices in the .dts files.
We also have the related data removed for at least omap4 in commit
3b9b10151c (ARM: OMAP4: hwmod data: Clean up the data file), so
that data is wrongly initialized as null data.
So we need to fix two bugs:
1. We are only checking the first entry of the ti,hwmods property
This means that we're only initializing the first hwmods entry
instead of the ones listed in the ti,hwmods property.
2. We are only checking the child nodes, not the nodes themselves
This means that anything listed at OCP level is currently just
ignored and unitialized and at least the omap4 case, with the
legacy data missing from the hwmod.
Fix both of the issues by using an index to the ti,hwmods property
and changing the hwmod lookup function to also check the current node
for ti,hwmods property instead of just the children.
While at it, let's also add some warnings for the bad data so it's
easier to fix.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
From Tony Lindgren:
Few more legacy booting vs device tree booting fixes that people
have noticed while booting things with device tree for things like
omap4 WLAN, smsc911x, and beagle audio. Hopefully this will be it
for the legacy booting vs device tree fixes for this -rc cycle.
* tag 'omap-for-v3.13/more-dt-regressions' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix the name of supplies for smsc911x shared by OMAP
ARM: OMAP2+: Powerdomain: Fix unchecked dereference of arch_pwrdm
ARM: dts: omap3-beagle: Add omap-twl4030 audio support
ARM: dts: omap4-sdp: Fix pin muxing for wl12xx
ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx
From Tony Lindgren:
Some omap related fixes that have come up with people moving to device
tree only based booting for omap2+.
The series contains a handful of fixes for the igep boards as they were
one of the first omap3 boards to jump over completely to device tree
based booting. So these can be considered regressions compared to
booting igep in legacy mode with board files in v3.12.
Also included are few other device tree vs legacy booting regressions:
- yet more missing omap3 .dtsi entries that have showed up booting
various boards with device tree only
- n900 eMMC device tree fix
- fixes for beagle USB EHCI
- two fixes to make omap2420 MMC work
As we're moving omap2+ to be device tree only for v3.14, I'd like to
have v3.13 work equally well for legacy based booting and device tree
based booting. So there will be likely few more device tree related
booting patches trickling in.
This series also includes a regression fix for the omap timer posted
mode that may wrongly stay on from the bootloader for some SoCs.
* tag 'omap-for-v3.13/fixes-against-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
mmc: omap: Fix I2C dependency and make driver usable with device tree
mmc: omap: Fix DMA configuration to not rely on device id
ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
ARM: dts: AM33XX IGEP0033: add USB support
ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
ARM: dts: AM33XX BASE0033: add pinmux and user led support
ARM: dts: AM33XX BASE0033: add pinmux and hdmi node to enable display
ARM: dts: omap3-igep0020: Add pinmuxing for DVI output
ARM: dts: omap3-igep0020: Add pinmux setup for i2c devices
ARM: dts: omap3-igep: Update to use the TI AM/DM37x processor
ARM: dts: omap3-igep: Add support for LBEE1USJYC WiFi connected to SDIO
ARM: dts: omap3-igep: Fix bus-width for mmc1
ARM: OMAP2+: dss-common: change IGEP's DVI DDC i2c bus
ARM: OMAP2+: Disable POSTED mode for errata i103 and i767
ARM: OMAP2+: Fix eMMC on n900 with device tree
ARM: OMAP2+: Add fixed regulator to omap2plus_defconfig
ARM: OMAP2+: Fix more missing data for omap3.dtsi file
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 'cd8abed' "ARM: OMAP2+: Powerdomain: Remove the need to
always have a voltdm associated to a pwrdm" leads to the following
Smatch complaint:
arch/arm/mach-omap2/powerdomain.c:131 _pwrdm_register()
error: we previously assumed 'arch_pwrdm' could be null (see line 105)
So, fix the unchecked dereference of arch_pwrdm.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
IGEP's DVI connector's DDC pins are connected to OMAP's third i2c bus.
When booting with Device Trees the requested bus number is set to -1
which means that the bus number should be dynamically assigned. So the
third i2c bus has 2 has a bus number.
Since now only DT booting is supported for IGEP boards after commit
06ff74fd ("ARM: OMAP2+: remove legacy support for IGEP boards"), the
i2c bus number has to be changed.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we need to configure the regulators and use the pdata
quirk to make eMMC work with device tree.
It seems that mostly vaux3 is used, and only some earlier revisions
used vmmc2. This has been tested to work on devices where the
system_rev passed by the bootloader has versions 0x0010, 0x2101
and 0x2204.
Cc: devicetree@vger.kernel.org
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@debian.org>
[tony@atomide.com: updated with pinctrl changes and comments from Sebastian]
Signed-off-by: Tony Lindgren <tony@atomide.com>
From Tony Lindgren:
Few more fixes for issues found booting older omaps using device tree.
Also few randconfig build fixes and removal of some dead code for omap4
as it no longer has legacy platform data based booting support.
* tag 'omap-for-v3.13/more-fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
Some omap3 code is throwing a warning:
arch/arm/mach-omap2/pm34xx.c: In function 'omap3_save_secure_ram_context':
arch/arm/mach-omap2/pm34xx.c:123:32: warning: cast to pointer from
integer of different size [-Wint-to-pointer-cast]
In reality this code will never actually execute with LPAE=y, since
Cortex-A8 doesn't support it. So downcasting the __pa() is safe in
this case.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Pull i2c changes from Wolfram Sang:
- new drivers for exynos5, bcm kona, and st micro
- bigger overhauls for drivers mxs and rcar
- typical driver bugfixes, cleanups, improvements
- got rid of the superfluous 'driver' member in i2c_client struct This
touches a few drivers in other subsystems. All acked.
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: bcm-kona: fix error return code in bcm_kona_i2c_probe()
i2c: i2c-eg20t: do not print error message in syslog if no ACK received
i2c: bcm-kona: Introduce Broadcom I2C Driver
i2c: cbus-gpio: Fix device tree binding
i2c: wmt: add missing clk_disable_unprepare() on error
i2c: designware: add new ACPI IDs
i2c: i801: Add Device IDs for Intel Wildcat Point-LP PCH
i2c: exynos5: Remove incorrect clk_disable_unprepare
i2c: i2c-st: Add ST I2C controller
i2c: exynos5: add High Speed I2C controller driver
i2c: rcar: fixup rcar type naming
i2c: scmi: remove some bogus NULL checks
i2c: sh_mobile & rcar: Enable the driver on all ARM platforms
i2c: sh_mobile: Convert to clk_prepare/unprepare
i2c: mux: gpio: use reg value for i2c_add_mux_adapter
i2c: mux: gpio: use gpio_set_value_cansleep()
i2c: Include linux/of.h header
i2c: mxs: Fix PIO mode on i.MX23
i2c: mxs: Rework the PIO mode operation
i2c: mxs: distinguish i.MX23 and i.MX28 based I2C controller
...
If CONFIG_SOC_HAS_REALTIME_COUNTER is not selected for omap5
or dra7xx, we can get the following error:
arch/arm/mach-omap2/built-in.o: In function `omap4_secondary_init':
:(.text+0x7ab0): undefined reference to `set_cntfreq'
Fix the issue by not trying to initalize the realtime counter
unles CONFIG_SOC_HAS_REALTIME_COUNTER is selected.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 26273e02a0 (ARM: OMAP2+: Fix build for dra7xx without
omap4 and 5) attempted to fix randconfig found errors for
redefinition of omap44xx_prm_reconfigure_io_chain, but was
not enough.
We need to check for AM43XX without any omap4 or 5 related
SoCs as well. And looks like we have prm44xx.o built always
anyways with omap-4-5-prcm-common because of the calls to
omap4_prm_vp_clear_txdone, so we can remove the duplicate
entries in the Makefile.
Signed-off-by: Tony Lindgren <tony@atomide.com>
A first set of batches of fixes for 3.13. The diffstat is large mostly
because we're adding a defconfig for a family that's been lacking it, and
there's some missing clock information added for i.MX and OMAP.
The at91 new code is around dealing with RTC/RTT reset at boot to fix possible
hangs due to pending wakeup interrupts coming in during early boot.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0oVK
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A first set of batches of fixes for 3.13. The diffstat is large
mostly because we're adding a defconfig for a family that's been
lacking it, and there's some missing clock information added for i.MX
and OMAP.
The at91 new code is around dealing with RTC/RTT reset at boot to fix
possible hangs due to pending wakeup interrupts coming in during early
boot"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: OMAP2+: Fix build for dra7xx without omap4 and 5
ARM: OMAP2+: omap_device: maintain sane runtime pm status around suspend/resume
doc: devicetree: Add bindings documentation for omap-des driver
ARM: dts: doc: Document missing compatible property for omap-sham driver
ARM: OMAP3: Beagle: fix return value check in beagle_opp_init()
ARM: at91: fix hanged boot due to early rtt-interrupt
ARM: at91: fix hanged boot due to early rtc-interrupt
video: exynos_mipi_dsim: Remove unused variable
ARM: highbank: only select errata 764369 if SMP
ARM: sti: only select errata 764369 if SMP
ARM: tegra: init fuse before setting reset handler
ARM: vt8500: add defconfig for v6/v7 chips
ARM: integrator_cp: Set LCD{0,1} enable lines when turning on CLCD
ARM: OMAP: devicetree: fix SPI node compatible property syntax items
pinctrl: single: call pcs_soc->rearm() whenever IRQ mask is changed
ARM: OMAP2+: smsc911x: fix return value check in gpmc_smsc911x_init()
MAINTAINERS: drop discontinued mailing list
ARM: dts: i.MX51: Fix OTG PHY clock
ARM: imx: set up pllv3 POWER and BYPASS sequentially
ARM: imx: pllv3 needs relock in .set_rate() call
...
Commit f2bf0e72d0 (ARM: OMAP2+: Add minimal 8250 support
for GPMC) added support for using bootloader timings for some
devices. Turns out we can do the same by looking at the compatible
flags of the child without adding a new function as smc91x has
a similar issue as 8250 with the bootloader timings.
And let's fix the 8250 naming, we should use the device type as
the name like uart instead of 8250 for zoom dts file.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we can get errors like:
arch/arm/mach-omap2/prm44xx.c:274: error: redefinition of ‘omap44xx_prm_reconfigure_io_chain’
arch/arm/mach-omap2/built-in.o: In function `default_finish_suspend':
arch/arm/mach-omap2/omap-mpuss-lowpower.c:95: undefined reference to `omap_do_wfi'
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP device hooks around suspend|resume_noirq ensures that hwmod
devices are forced to idle using omap_device_idle/enable as part of
the last stage of suspend activity.
For a device such as i2c who uses autosuspend, it is possible to enter
the suspend path with dev->power.runtime_status = RPM_ACTIVE.
As part of the suspend flow, the generic runtime logic would increment
it's dev->power.disable_depth to 1. This should prevent further
pm_runtime_get_sync from succeeding once the runtime_status has been
set to RPM_SUSPENDED.
Now, as part of the suspend_noirq handler in omap_device, we force the
following: if the device status is !suspended, we force the device
to idle using omap_device_idle (clocks are cut etc..). This ensures
that from a hardware perspective, the device is "suspended". However,
runtime_status is left to be active.
*if* an operation is attempted after this point to
pm_runtime_get_sync, runtime framework depends on runtime_status to
indicate accurately the device status, and since it sees it to be
ACTIVE, it assumes the module is functional and returns a non-error
value. As a result the user will see pm_runtime_get succeed, however a
register access will crash due to the lack of clocks.
To prevent this from happening, we should ensure that runtime_status
exactly indicates the device status. As a result of this change
any further calls to pm_runtime_get* would return -EACCES (since
disable_depth is 1). On resume, we restore the clocks and runtime
status exactly as we suspended with. These operations are not expected
to fail as we update the states after the core runtime framework has
suspended itself and restore before the core runtime framework has
resumed.
Cc: stable@vger.kernel.org # v3.4+
Reported-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In case of error, the function get_cpu_device() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In case of error, the function platform_device_register_resndata()
returns ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from
Mika Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh Kumar,
Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz Majewski,
Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki,
Naresh Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani,
Zhang Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko,
Al Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=JCxk
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael J Wysocki:
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from Mika
Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh
Kumar, Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz
Majewski, Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki, Naresh
Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani, Zhang
Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko, Al
Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
* tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (386 commits)
cpufreq: conservative: fix requested_freq reduction issue
ACPI / hotplug: Consolidate deferred execution of ACPI hotplug routines
PM / runtime: Use pm_runtime_put_sync() in __device_release_driver()
ACPI / event: remove unneeded NULL pointer check
Revert "ACPI / video: Ignore BIOS initial backlight value for HP 250 G1"
ACPI / video: Quirk initial backlight level 0
ACPI / video: Fix initial level validity test
intel_pstate: skip the driver if ACPI has power mgmt option
PM / hibernate: Avoid overflow in hibernate_preallocate_memory()
ACPI / hotplug: Do not execute "insert in progress" _OST
ACPI / hotplug: Carry out PCI root eject directly
ACPI / hotplug: Merge device hot-removal routines
ACPI / hotplug: Make acpi_bus_hot_remove_device() internal
ACPI / hotplug: Simplify device ejection routines
ACPI / hotplug: Fix handle_root_bridge_removal()
ACPI / hotplug: Refuse to hot-remove all objects with disabled hotplug
ACPI / scan: Start matching drivers after trying scan handlers
ACPI: Remove acpi_pci_slot_init() headers from internal.h
ACPI / blacklist: fix name of ThinkPad Edge E530
PowerCap: Fix build error with option -Werror=format-security
...
Conflicts:
arch/arm/mach-omap2/opp.c
drivers/Kconfig
drivers/spi/spi.c
* Unify some compile-time differences so that we have fewer uses of
#ifdef CONFIG_OF in atmel_nand
* Other general cleanups (removing unused functions, options, variables,
fields; use correct interfaces)
* Fix BUG() for new odd-sized NAND, which report non-power-of-2 dimensions via
ONFI
* Miscellaneous driver fixes (SPI NOR flash; BCM47xx NAND flash; etc.)
* Improve differentiation between SLC and MLC NAND -- this clarifies an ABI
issue regarding the MTD "type" (in sysfs and in ioctl(MEMGETINFO)), where
the MTD_MLCNANDFLASH type was present but inconsistently used
* Extend GPMI NAND to support multi-chip-select NAND for some platforms
* Many improvements to the OMAP2/3 NAND driver, including an expanded DT
binding to bring us closer to mainline support for some OMAP systems
* Fix a deadlock in the error path of the Atmel NAND driver probe
* Correct the error codes from MTD mmap() to conform to POSIX and the Linux
Programmer's Manual. This is an acknowledged change in the MTD ABI, but I
can't imagine somebody relying on the non-standard -ENOSYS error code
specifically. Am I just being unimaginative? :)
* Fix a few important GPMI NAND bugs (one regression from 3.12 and one
long-standing race condition)
* More? Read the log!
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=z5qO
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20131112' of git://git.infradead.org/linux-mtd
Pull MTD changes from Brian Norris:
- Unify some compile-time differences so that we have fewer uses of
#ifdef CONFIG_OF in atmel_nand
- Other general cleanups (removing unused functions, options,
variables, fields; use correct interfaces)
- Fix BUG() for new odd-sized NAND, which report non-power-of-2
dimensions via ONFI
- Miscellaneous driver fixes (SPI NOR flash; BCM47xx NAND flash; etc.)
- Improve differentiation between SLC and MLC NAND -- this clarifies an
ABI issue regarding the MTD "type" (in sysfs and in the MEMGETINFO
ioctl), where the MTD_MLCNANDFLASH type was present but
inconsistently used
- Extend GPMI NAND to support multi-chip-select NAND for some platforms
- Many improvements to the OMAP2/3 NAND driver, including an expanded
DT binding to bring us closer to mainline support for some OMAP
systems
- Fix a deadlock in the error path of the Atmel NAND driver probe
- Correct the error codes from MTD mmap() to conform to POSIX and the
Linux Programmer's Manual. This is an acknowledged change in the MTD
ABI, but I can't imagine somebody relying on the non-standard -ENOSYS
error code specifically. Am I just being unimaginative? :)
- Fix a few important GPMI NAND bugs (one regression from 3.12 and one
long-standing race condition)
- More? Read the log!
* tag 'for-linus-20131112' of git://git.infradead.org/linux-mtd: (98 commits)
mtd: gpmi: fix the NULL pointer
mtd: gpmi: fix kernel BUG due to racing DMA operations
mtd: mtdchar: return expected errors on mmap() call
mtd: gpmi: only scan two chips for imx6
mtd: gpmi: Use devm_kzalloc()
mtd: atmel_nand: fix bug driver will in a dead lock if no nand detected
mtd: nand: use a local variable to simplify the nand_scan_tail
mtd: nand: remove deprecated IRQF_DISABLED
mtd: dataflash: Say if we find a device we don't support
mtd: nand: omap: fix error return code in omap_nand_probe()
mtd: nand_bbt: kill NAND_BBT_SCANALLPAGES
mtd: m25p80: fixup device removal failure path
mtd: mxc_nand: Include linux/of.h header
mtd: remove duplicated include from mtdcore.c
mtd: m25p80: add support for Macronix mx25l3255e
mtd: nand: omap: remove selection of BCH ecc-scheme via KConfig
mtd: nand: omap: updated devm_xx for all resource allocation and free calls
mtd: nand: omap: use drivers/mtd/nand/nand_bch.c wrapper for BCH ECC instead of lib/bch.c
mtd: nand: omap: clean-up ecc layout for BCH ecc schemes
mtd: nand: omap2: clean-up BCHx_HW and BCHx_SW ECC configurations in device_probe
...
Pull LED subsystem changes from Bryan Wu:
"LED subsystem updates for 3.13 are basically cleanup and also add a
new driver for PCA9685"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: lp55xx: handle enable pin in driver
leds-gpio: of: led should not be created if its status is disabled
of: introduce of_get_available_child_count
leds: Added driver for the NXP PCA9685 I2C chip
leds: pwm: Remove redundant of_match_ptr
leds: Include linux/of.h header
leds: dac124s085: Remove redundant spi_set_drvdata
leds: lp55xx: enable setting default trigger
leds: blinkm: Remove redundant break
Most of this branch consists of updates, additions and general churn of
the device tree source files in the kernel (arch/arm/boot/dts). Besides
that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board files
for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as well
- Some updates to pinctrl and other subsystems. Most of these are for
DT-enablement of the various platforms and acks have been collected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nH67
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Most of this branch consists of updates, additions and general churn
of the device tree source files in the kernel (arch/arm/boot/dts).
Besides that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board
files for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
well
- Some updates to pinctrl and other subsystems. Most of these are
for DT-enablement of the various platforms and acks have been
collected"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
ARM: dts: bcm281xx: Add card detect GPIO
ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
ARM: bcm281xx: Add device node for the GPIO controller
ARM: mvebu: Add Netgear ReadyNAS 104 board
ARM: tegra: fix Tegra114 IOMMU register address
ARM: kirkwood: add support for OpenBlocks A7 platform
ARM: dts: omap4-panda: add DPI pinmuxing
ARM: dts: AM33xx: Add RNG node
ARM: dts: AM33XX: Add hwspinlock node
ARM: dts: OMAP5: Add hwspinlock node
ARM: dts: OMAP4: Add hwspinlock node
ARM: dts: use 'status' property for PCIe nodes
ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
ARM: mvebu: Add the core-divider clock to Armada 370/XP
...
Board-related updates. This branch is getting smaller and smaller, which is
the whole idea so that's reassuring.
Right now by far most of the code is related to shmobile updates, and
they are now switching over to removal of board code and migration to
multiplatform, so we'll see their board code base shrink in the near
future too, I hope.
In addition to that is some defconfig updates, some display updates for OMAP
and a bit of new board support for Rockchip boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSgBsmAAoJEIwa5zzehBx3m3oP/ingw9VE69O3GLjd2zWI35HJ
+NuFmwlWFj+1XLysfCxHJn3rvkMJKM33ZcP6FkgJGMHfQRRBmrC0REG/nQq59riE
c7R+Jguw044kAGH3evg4kCJ3gI+WD+H+juKf4IQ9bYDaneZGN9f0hkuzLRbmqwZP
RIDa+q+Oo6Q3pcTUvkz2lMV6q7Ydb5H49suyPN+9muJ1wVYjFR+XuvnYzy/PO2lF
kyIN2fijQN278QjM6eZEtsFoB7L7NmuZr8ZBTkekHSfybqIsb59JEqZER7huJSdR
fEk0VQ/A6M2LQSRTL+UrCadFYaxDnW8wjxbpLUikhg7ONnrCBSGvVj4nFiEKAFdE
R49YZ2hqhrXjie1kGoKuXGmxGG/7ODJWmWDgnIXx0daSOgPUomlO8YKtGeBO1/Zf
6wsvAjiukcLV10JEF/rCslTEA/Ck5dJZjV6S/8hSy1N+CF4qZflSmXG0gb9tB+nv
ztRN9gTlJSr/MpIE3jpbPFxNwef+UPW/R8fnO7fdnzPeOpwTDzZ1ydArC0IIpmgt
Ngum5iyP4qcwZ91hWXhdAu3ZGeHWZ5tox1W/DMjkyTxCEDUUdtfkChOGf/Wmjg7z
Rl5nyH2Y4xT0+Otn/0LIqKvEh1JwwX9FlIqkJI4IMrnYJwHQ4oBvOAGskW1ZsFPQ
0OBbAAHS1tio3ZywNMIQ
=ZYOa
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"Board-related updates. This branch is getting smaller and smaller,
which is the whole idea so that's reassuring.
Right now by far most of the code is related to shmobile updates, and
they are now switching over to removal of board code and migration to
multiplatform, so we'll see their board code base shrink in the near
future too, I hope.
In addition to that is some defconfig updates, some display updates
for OMAP and a bit of new board support for Rockchip boards"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (56 commits)
ARM: rockchip: add support for rk3188 and Radxa Rock board
ARM: rockchip: add dts for bqcurie2 tablet
ARM: rockchip: enable arm-global-timer
ARM: rockchip: move shared dt properties to common source file
ARM: OMAP2+: display: Create omap_vout device inside omap_display_init
ARM: OMAP2+: display: Create omapvrfb and omapfb devices inside omap_display_init
ARM: OMAP2+: display: Create omapdrm device inside omap_display_init
ARM: OMAP2+: drm: Don't build device for DMM
ARM: tegra: defconfig updates
RX-51: Add support for OMAP3 ROM Random Number Generator
ARM: OMAP3: RX-51: ARM errata 430973 workaround
ARM: OMAP3: Add secure function omap_smc3() which calling instruction smc #1
ARM: shmobile: marzen: enable INTC IRQ
ARM: shmobile: bockw: add SMSC support on reference
ARM: shmobile: Use SMP on Koelsch
ARM: shmobile: Remove KZM9D reference DTS
ARM: shmobile: Let KZM9D multiplatform boot with KZM9D DTB
ARM: shmobile: Remove non-multiplatform KZM9D reference support
ARM: shmobile: Use KZM9D without reference for multiplatform
ARM: shmobile: Sync KZM9D DTS with KZM9D reference DTS
...
New and updated SoC support. Among the things new for this release are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as ARCH_BCM,
and turned out to be too broad a name. New name is ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the platform code
more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is more work
on consolidation instead of introduction of new non-multiplatform SoCs, we're
all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WYJl
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Among the things new for this release
are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as
ARCH_BCM, and turned out to be too broad a name. New name is
ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the
platform code more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is
more work on consolidation instead of introduction of new
non-multiplatform SoCs, we're all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates,
etc"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (159 commits)
ARM: bcm281xx: Add ARCH_BCM_MOBILE to bcm config
ARM: bcm_defconfig: Run "make savedefconfig"
ARM: bcm281xx: Add ARCH Timers to config
rename ARCH_BCM to ARCH_BCM_MOBILE (mach-bcm)
ARM: vexpress: Enable platform-specific options in defconfig
ARM: vexpress: Make defconfig work again
ARM: sunxi: remove .init_time hooks
ARM: imx: enable suspend for imx6sl
ARM: imx: ensure dsm_request signal is not asserted when setting LPM
ARM: imx6q: call WB and RBC configuration from imx6q_pm_enter()
ARM: imx6q: move low-power code out of clock driver
ARM: imx: drop extern with function prototypes in common.h
ARM: imx: reset core along with enable/disable operation
ARM: imx: do not return from imx_cpu_die() call
ARM: imx_v6_v7_defconfig: Select CONFIG_PROVE_LOCKING
ARM: imx_v6_v7_defconfig: Enable LEDS_GPIO related options
ARM: mxs_defconfig: Turn off CONFIG_DEBUG_GPIO
ARM: imx: replace imx6q_restart() with mxc_restart()
ARM: mach-imx: mm-imx5: Retrieve iomuxc base address from dt
ARM: mach-imx: mm-imx5: Retrieve tzic base address from dt
...
This branch contains code cleanups, moves and removals for 3.13.
Qualcomm msm targets had a bunch of code removal for legacy non-DT
platforms. Nomadik saw more device tree conversions and cleanup of old
code. Tegra has some code refactoring, etc.
One longish patch series from Sebastian Hasselbarth changes the init_time
hooks and tries to use a generic implementation for most platforms,
since they were all doing more or less the same things.
Finally the "shark" platform is removed in this release. It's been
abandoned for a while and nobody seems to care enough to keep it
around. If someone comes along and wants to resurrect it, the removal
can easily be reverted and code brought back.
Beyond this, mostly a bunch of removals of stale content across the
board, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=SHZQ
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.13.
Qualcomm msm targets had a bunch of code removal for legacy non-DT
platforms. Nomadik saw more device tree conversions and cleanup of
old code. Tegra has some code refactoring, etc.
One longish patch series from Sebastian Hasselbarth changes the
init_time hooks and tries to use a generic implementation for most
platforms, since they were all doing more or less the same things.
Finally the "shark" platform is removed in this release. It's been
abandoned for a while and nobody seems to care enough to keep it
around. If someone comes along and wants to resurrect it, the removal
can easily be reverted and code brought back.
Beyond this, mostly a bunch of removals of stale content across the
board, etc"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (79 commits)
ARM: gemini: convert to GENERIC_CLOCKEVENTS
ARM: EXYNOS: remove CONFIG_MACH_EXYNOS[4, 5]_DT config options
ARM: OMAP3: control: add API for setting IVA bootmode
ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
ARM: OMAP3: McBSP: do not access CM register directly
ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
MAINTAINERS: Add patterns for DTS files for AT91
ARM: at91: remove init_machine() as default is suitable
ARM: at91/dt: split sama5d3 peripheral definitions
ARM: at91/dt: split sam9x5 peripheral definitions
ARM: Remove temporary sched_clock.h header
ARM: clps711x: Use linux/sched_clock.h
MAINTAINERS: Add DTS files to patterns for Samsung platform
ARM: EXYNOS: remove unnecessary header inclusions from exynos4/5 dt machine file
ARM: tegra: fix ARCH_TEGRA_114_SOC select sort order
clk: nomadik: fix missing __init on nomadik_src_init
ARM: drop explicit selection of HAVE_CLK and CLKDEV_LOOKUP
ARM: S3C64XX: Kill CONFIG_PLAT_S3C64XX
ASoC: samsung: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
...
A set of fixes for various platforms that weren't considered bad enough
to include in 3.12 (nor -stable). Mostly simple typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=70+h
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC low-priority fixes from Olof Johansson:
"A set of fixes for various platforms that weren't considered bad
enough to include in 3.12 (nor -stable). Mostly simple typo fixes,
etc"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP2+: irq, AM33XX add missing register check
ARM: OMAP2+: wakeupgen: AM43x adaptation
ARM: OMAP1: Fix a bunch of GPIO related section warnings after initdata got corrected
ARM: dts: fix PL330 MDMA1 address in DT for Universal C210 board
ARM: dts: Work around lack of cpufreq regulator lookup for exynos4210-origen and trats boards
ARM: dts: Fix typo earlyprintk in exynos5440-sd5v1 and ssdk5440 boards
ARM: dts: Correct typo in use of samsung,pin-drv for exynos5250
ARM: rockchip: remove obsolete rockchip,config properties
ARM: rockchip: fix wrong use of non-existent CONFIG_LOCAL_TIMERS
ARM: mach-omap1: Fix omap1510_fpga_init_irq() implicit declarations.
ARM: OMAP1: fix incorrect placement of __initdata tag
ARM: OMAP: remove deprecated IRQF_DISABLED
ARM: OMAP2+: throw the die id into the entropy pool
OMAP NAND driver support multiple ECC scheme, which can used in different
flavours, depending on in-build Hardware engines present on SoC.
This patch updates following in DT bindings related to sectionion of ecc-schemes
- ti,elm-id: replaces elm_id (maintains backward compatibility)
- ti,nand-ecc-opts: selection of h/w or s/w implementation of an ecc-scheme
depends on ti,elm-id. (supported values ham1, bch4, and bch8)
- maintain backward compatibility to deprecated DT bindings (sw, hw, hw-romcode)
Below table shows different flavours of ecc-schemes supported by OMAP devices
+---------------------------------------+---------------+---------------+
| ECC scheme |ECC calculation|Error detection|
+---------------------------------------+---------------+---------------+
|OMAP_ECC_HAM1_CODE_HW |H/W (GPMC) |S/W |
+---------------------------------------+---------------+---------------+
|OMAP_ECC_BCH8_CODE_HW_DETECTION_SW |H/W (GPMC) |S/W |
|(requires CONFIG_MTD_NAND_ECC_BCH) | | |
+---------------------------------------+---------------+---------------+
|OMAP_ECC_BCH8_CODE_HW |H/W (GPMC) |H/W (ELM) |
|(requires CONFIG_MTD_NAND_OMAP_BCH && | | |
| ti,elm-id in DT) | | |
+---------------------------------------+---------------+---------------+
To optimize footprint of omap2-nand driver, selection of some ECC schemes
also require enabling following Kconfigs, in addition to setting appropriate
DT bindings
- Kconfig:CONFIG_MTD_NAND_ECC_BCH error detection done in software
- Kconfig:CONFIG_MTD_NAND_OMAP_BCH error detection done by h/w engine
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Move some of the OMAP2+ CM and System Control Module direct
register accesses into CM- and System Control
Module-specific "drivers" underneath arch/arm/mach-omap2/. This
is a prerequisite for moving this code out of arch/arm/mach-omap2/ into
drivers/.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/cm_scm_cleanup_a_v3.13/20131019101809/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=L37r
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/cm-scm-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Paul Walmsley <paul@pwsan.com> via Tony Lindgren:
Move some of the OMAP2+ CM and System Control Module direct
register accesses into CM- and System Control
Module-specific "drivers" underneath arch/arm/mach-omap2/. This
is a prerequisite for moving this code out of arch/arm/mach-omap2/ into
drivers/.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/cm_scm_cleanup_a_v3.13/20131019101809/
* tag 'omap-for-v3.13/cm-scm-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: control: add API for setting IVA bootmode
ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
ARM: OMAP3: McBSP: do not access CM register directly
ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
+ Linux 3.12-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
Since Operating Performance Points (OPP) functions are specific
to device specific power management, be specific and rename opp.h
to pm_opp.h
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since Operating Performance Points (OPP) data structures are specific
to device specific power management, be specific and rename opp_* data
structures in OPP library with dev_pm_opp_* equivalent.
Affected structures are:
struct opp
enum opp_event
Minor checkpatch warning resulting of this change was fixed as well.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since Operating Performance Points (OPP) functions are specific to
device specific power management, be specific and rename opp_*
accessors in OPP library with dev_pm_opp_* equivalent.
Affected functions are:
opp_get_voltage
opp_get_freq
opp_get_opp_count
opp_find_freq_exact
opp_find_freq_floor
opp_find_freq_ceil
opp_add
opp_enable
opp_disable
opp_get_notifier
opp_init_cpufreq_table
opp_free_cpufreq_table
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch moves the handling of the chip's enable pin from the board
code into the driver. It also updates all board-code files using the
driver to incorporate this change.
This is needed for device tree support of the enable pin.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=LDY7
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.13
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
dpll4_m3_ck and dpll4_m4_ck have divider bit fields which are 6 bits
wide. However, only values from 1 to 32 are allowed. This means we have
to add a divider tables and list the dividers explicitly.
I believe the same issue is there for other dpll4_mx_ck clocks, but as
I'm not familiar with them, I didn't touch them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Set CLK_SET_RATE_PARENT flag for dss1_alwon_fck_3430es2,
dss1_alwon_fck_3430es1 and dpll4_m4x2_ck so that the DSS's fclk can be
configured without the need to get the parent's parent of the fclk.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Set CLK_SET_RATE_PARENT flag for dss_dss_clk so that the DSS's fclk can
be configured without the need to get the parent of the fclk.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
With OMAP3+ and AM33xx supported SoC having defined CPU device tree
entries with operating-points and clock nodes defined, we can now use
the SoC generic cpufreq-cpu0 driver by registering appropriate device.
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM335x, AM43xx, OMAP5 and DRA7 have missing late init hook. Introduce
SoC specific hook with a call to OMAP2+ generic lateinit hook. This
allows the generic late initializations such as cpufreq hooks to be
active.
Based on out-of-tree patches that need to be introduced in
mainline, this introduction allows us to provide the foundation for
further SoC specific features as they are developed.
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3+ supports both device tree and non-device tree boot.
Device tree bindings for OMAP3+ is supposed to be added via dts following:
Documentation/devicetree/bindings/power/opp.txt
Since we now have device tree entries for OMAP3+ cpu OPPs,
The current code wrongly adds duplicate OPPs. So, dont register OPPs
when booting using device tree.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
am33xx has a INTC_PENDING_IRQ3 register that is not checked for pending
interrupts. This patch adds AM33XX to the ifdef of SOCs that have to
check this register.
Cc: stable@vger.kernel.org
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
