A host running in VHE mode gets the EL2 physical timer as its time
source (accessed using the EL1 sysreg accessors, which get re-directed
to the EL2 sysregs by VHE).
The EL1 physical timer remains unused by the host kernel, allowing us to
pass that on directly to a KVM guest and saves us from emulating this
timer for the guest on VHE systems.
Store the EL1 Physical Timer's IRQ number in
struct arch_timer_kvm_info on VHE systems to allow KVM to use it.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
The current delay implementation uses the yield instruction, which is a
hint that it is beneficial to schedule another thread. As this is a hint,
it may be implemented as a NOP, causing all delays to be busy loops. This
is the case for many existing CPUs.
Taking advantage of the generic timer sending periodic events to all
cores, we can use WFE during delays to reduce power consumption. This is
beneficial only for delays longer than the period of the timer event
stream.
If timer event stream is not enabled, delays will behave as yield/busy
loops.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The arch timer configuration for a CPU might get reset after suspending
said CPU.
In order to reliably use the event stream in the kernel (e.g. for delays),
we keep track of the state where we can safely consider the event stream as
properly configured. After writing to cntkctl, we issue an ISB to ensure
that subsequent delay loops can rely on the event stream being enabled.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In preparation for ACPI GTDT support, this patch adds structs to
describe the MMIO timers indepedent of the firmware interface.
Subsequent patches will use these to split the FW/HW probing logic, so
that the HW probing logic can be shared by ACPI and DT.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
This patch add a new enum "arch_timer_spi_nr" and use it in the driver.
Just for code's readability, no functional change.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
To support the arm_arch_timer via ACPI we need to share defines and enums
between the driver and the ACPI parser code.
So we split out the relevant defines and enums into arm_arch_timer.h.
No functional change.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
The only call of arch_timer_get_timecounter (in KVM) has been removed.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Currently, the firmware table is parsed by the virtual timer code in
order to retrieve the virtual timer interrupt. However, this is already
done by the arch timer driver.
To avoid code duplication, extend arch_timer_kvm_info to get the virtual
IRQ.
Note that the KVM code will be modified in a subsequent patch.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Introduce a structure which are filled up by the arch timer driver and
used by the virtual timer in KVM.
The first member of this structure will be the timecounter. More members
will be added later.
A stub for the new helper isn't introduced because KVM requires the arch
timer for both ARM64 and ARM32.
The function arch_timer_get_timecounter is kept for the time being and
will be dropped in a subsequent patch.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The timecounter code has almost nothing to do with the clocksource
code. Let it live in its own file. This will help isolate the
timecounter users from the clocksource users in the source tree.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ARM architected timer can generate events (used for waking up
CPUs executing the wfe instruction) at a frequency represented as a
power-of-2 divisor of the clock rate.
An event stream might be used:
- To implement wfe-based timeouts for userspace locking implementations.
- To impose a timeout on a wfe for safeguarding against any programming
error in case an expected event is not generated.
This patch computes the event stream frequency aiming for a period
of 100us between events. It uses ARM/ARM64 specific backends to configure
and enable the event stream.
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
[sudeep: moving ARM/ARM64 changes into separate patches
and adding Kconfig option]
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Add macros to describe the bitfields in the ARM architected timer
control register to make code easy to understand.
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Add support for the memory mapped timers by filling in the
read/write functions and adding some parsing code. Note that we
only register one clocksource, preferring the cp15 based
clocksource over the mmio one.
To keep things simple we register one global clockevent. This
covers the case of UP and SMP systems with only mmio hardware and
systems where the memory mapped timers are used as the broadcast
timer in low power modes.
The DT binding allows for per-CPU memory mapped timers in case we
want to support that in the future, but the code isn't added
here. We also don't do much for hypervisor support, although it
should be possible to support it by searching for at least two
frames where one frame has the virtual capability and then
updating KVM timers to support it.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <Marc.Zyngier@arm.com>
Cc: Rob Herring <robherring2@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Using an enum for the register we wish to access allows newer
compilers to determine if we've forgotten a case in our switch
statement. This allows us to remove the BUILD_BUG() instances in
the arm64 port, avoiding problems where optimizations may not
happen.
To try and force better code generation we're currently marking
the accessor functions as inline, but newer compilers can ignore
the inline keyword unless it's marked __always_inline. Luckily on
arm and arm64 inline is __always_inline, but let's make
everything __always_inline to be explicit.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <Marc.Zyngier@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Switching between reading the virtual or physical counters is
problematic, as some core code wants a view of time before we're fully
set up. Using a function pointer and switching the source after the
first read can make time appear to go backwards, and having a check in
the read function is an unfortunate block on what we want to be a fast
path.
Instead, this patch makes us always use the virtual counters. If we're a
guest, or don't have hyp mode, we'll use the virtual timers, and as such
don't care about CNTVOFF as long as it doesn't change in such a way as
to make time appear to travel backwards. As the guest will use the
virtual timers, a (potential) KVM host must use the physical timers
(which can wake up the host even if they fire while a guest is
executing), and hence a host must have CNTVOFF set to zero so as to have
a consistent view of time between the physical timers and virtual
counters.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rob Herring <rob.herring@calxeda.com>
This converts arm and arm64 to use CLKSRC_OF DT based initialization for
the arch timer. A new function arch_timer_arch_init is added to allow for
arch specific setup.
This has a side effect of enabling sched_clock on omap5 and exynos5. There
should not be any reason not to use the arch timers for sched_clock.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Fixes:
In file included from arch/arm/include/asm/arch_timer.h:10:0,
from arch/arm/mach-shmobile/timer.c:23:
include/clocksource/arm_arch_timer.h:56:28: warning: 'arch_timer_get_timecounter' defined but not used [-Wunused-function]
Signed-off-by: Olof Johansson <olof@lixom.net>
The core functionality of the arch_timer driver is not directly tied to
anything under arch/arm, and can be split out.
This patch factors out the core of the arch_timer driver, so it can be
shared with other architectures. A couple of functions are added so
that architecture-specific code can interact with the driver without
needing to touch its internals.
The ARM_ARCH_TIMER config variable is moved out to
drivers/clocksource/Kconfig, existing uses in arch/arm are replaced with
HAVE_ARM_ARCH_TIMER, which selects it.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
