Commit 9e3c0066 (ARM: dts: imx6q-arm2: add pinctrl for uart and enet)
defines NANDF_CS pins as gpio in 'hog', assuming these two pins are
always used by usdhc3 in gpio mode as card-detection and
write-protection on ARM2 board. But it's not true. These pins are
shared by usdhc3 and gpmi-nand. We should have the pins functional
for gpmi-nand when usdhc3 is disabled.
Move the pins out of 'hog', so that pins only work in gpio mode as CD
and WP when usdhc3 is enabled, and otherwise they are available for
gpmi-nand.
Reported-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the DT node for gpmi nand.
Add the pinmux support for gpmi nand.
The gpmi nand may conflicts with other modules, such as MMC.
So we do not enable the gpmi nand for mx6q-arm2 board, just add the
node for the board.
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Changes in the dt2 branch move stuff around that gets changed
in the drivers/mmc branch. I chose a non-obvious resolution by
adding the new bus-width property into all the tegra sdhci device
nodes.
Conflicts:
arch/arm/boot/dts/tegra-cardhu.dts
arch/arm/boot/dts/tegra-harmony.dts
arch/arm/boot/dts/tegra-ventana.dts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch unifies the current DT MMC bindings documentation and code,
adds generic MMC DT bindings documentation, and updates .dts files for
consistency.
[cjb: typo fixes, addition of max-frequency property]
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Do not hardcode the local mac address.
Let bootloader retrieve it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It has been pointed out by device tree maintainer for several times
that the generic names 'serial' and 'ethernet' should be used for
those devices per ePAPR. Renames imx uart and fec device tree nodes
to stop them being bad examples.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove bootargs field as this information is retrieved from the bootloader.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The Sabreauto board was renamed to Armadillo2 recently. To avoid
confusion, rename Sabreauto to Armadillo2/arm2.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2011-12-14 21:25:46 +08:00
Renamed from arch/arm/boot/dts/imx6q-sabreauto.dts (Browse further)
