[ Upstream commit e8d1b41e69 ]
With the to-be-fixed commit, the reset_work handler cleared 'host->mrq'
outside of the spinlock protected critical section. That leaves a small
race window during execution of 'tmio_mmc_reset()' where the done_work
handler could grab a pointer to the now invalid 'host->mrq'. Both would
use it to call mmc_request_done() causing problems (see link below).
However, 'host->mrq' cannot simply be cleared earlier inside the
critical section. That would allow new mrqs to come in asynchronously
while the actual reset of the controller still needs to be done. So,
like 'tmio_mmc_set_ios()', an ERR_PTR is used to prevent new mrqs from
coming in but still avoiding concurrency between work handlers.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Closes: https://lore.kernel.org/all/20240220061356.3001761-1-dirk.behme@de.bosch.com/
Fixes: df3ef2d3c9 ("mmc: protect the tmio_mmc driver against a theoretical race")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Dirk Behme <dirk.behme@de.bosch.com>
Cc: stable@vger.kernel.org # 3.0+
Link: https://lore.kernel.org/r/20240305104423.3177-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae5004a40a ]
This looks strange to call release_mem_region() in a remove function
without any request_mem_region() in the probe or "struct resource"
somewhere.
So remove the corresponding code.
Fixes: 3a96dff0f8 ("mmc: SD/MMC Host Controller for Wondermedia WM8505/WM8650")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/bb0bb1ed1e18de55e8c0547625bde271e64b8c31.1708983064.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ff3206d218 upstream.
Initializing an eMMC that's connected via a 1-bit bus is current failing,
if the HW (DT) informs that 4-bit bus is supported. In fact this is a
regression, as we were earlier capable of falling back to 1-bit mode, when
switching to 4/8-bit bus failed. Therefore, let's restore the behaviour.
Log for Samsung eMMC 5.1 chip connected via 1bit bus (only D0 pin)
Before patch:
[134509.044225] mmc0: switch to bus width 4 failed
[134509.044509] mmc0: new high speed MMC card at address 0001
[134509.054594] mmcblk0: mmc0:0001 BGUF4R 29.1 GiB
[134509.281602] mmc0: switch to bus width 4 failed
[134509.282638] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.282657] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.284598] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.284602] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.284609] ldm_validate_partition_table(): Disk read failed.
[134509.286495] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.286500] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.288303] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.288308] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.289540] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.289544] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.289553] mmcblk0: unable to read partition table
[134509.289728] mmcblk0boot0: mmc0:0001 BGUF4R 31.9 MiB
[134509.290283] mmcblk0boot1: mmc0:0001 BGUF4R 31.9 MiB
[134509.294577] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[134509.295835] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.295841] Buffer I/O error on dev mmcblk0, logical block 0, async page read
After patch:
[134551.089613] mmc0: switch to bus width 4 failed
[134551.090377] mmc0: new high speed MMC card at address 0001
[134551.102271] mmcblk0: mmc0:0001 BGUF4R 29.1 GiB
[134551.113365] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21
[134551.114262] mmcblk0boot0: mmc0:0001 BGUF4R 31.9 MiB
[134551.114925] mmcblk0boot1: mmc0:0001 BGUF4R 31.9 MiB
Fixes: 577fb13199 ("mmc: rework selection of bus speed mode")
Cc: stable@vger.kernel.org
Signed-off-by: Ivan Semenov <ivan@semenov.dev>
Link: https://lore.kernel.org/r/20240206172845.34316-1-ivan@semenov.dev
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 09f164d393 ]
The sdhci_omap is specific to older TI SoCs, update the
dependencies for those SoCs and compile testing. While we're
at it update the text to reflect the wider range of
supported TI SoCS the driver now supports.
Fixes: 7d326930d3 ("mmc: sdhci-omap: Add OMAP SDHCI driver")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20231220135950.433588-2-pbrobinson@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e7794c14fd upstream.
When RPMB was converted to a character device, it added support for
multiple RPMB partitions (Commit 97548575be ("mmc: block: Convert RPMB to
a character device").
One of the changes in this commit was transforming the variable target_part
defined in __mmc_blk_ioctl_cmd into a bitmask. This inadvertently regressed
the validation check done in mmc_blk_part_switch_pre() and
mmc_blk_part_switch_post(), so let's fix it.
Fixes: 97548575be ("mmc: block: Convert RPMB to a character device")
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231201153143.1449753-1-jorge@foundries.io
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c616696a90 upstream.
STOP command does not guarantee to wait while busy, but subsequent command
MMC_CMDQ_TASK_MGMT to discard the queue will fail if the card is busy, so
be sure to wait by employing mmc_poll_for_busy().
Fixes: 72a5af554d ("mmc: core: Add support for handling CQE requests")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Christian Loehle <christian.loehle@arm.com>
Link: https://lore.kernel.org/r/20231103084720.6886-4-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8155d1fa3a ]
It is important that MMC_CMDQ_TASK_MGMT command to discard the queue is
successful because otherwise a subsequent reset might fail to flush the
cache first. Retry it and the previous STOP command.
Fixes: 72a5af554d ("mmc: core: Add support for handling CQE requests")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20231103084720.6886-5-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1de1b77982 ]
If a task completion notification (TCN) is received when there is no
outstanding task, the cqhci driver issues a "spurious TCN" warning. This
was observed to happen right after CQE error recovery.
When an error interrupt is received the driver runs recovery logic.
It halts the controller, clears all pending tasks, and then re-enables
it. On some platforms, like Intel Jasper Lake, a stale task completion
event was observed, regardless of the CQHCI_CLEAR_ALL_TASKS bit being set.
This results in either:
a) Spurious TC completion event for an empty slot.
b) Corrupted data being passed up the stack, as a result of premature
completion for a newly added task.
Rather than add a quirk for affected controllers, ensure tasks are cleared
by toggling CQHCI_ENABLE, which would happen anyway if
cqhci_clear_all_tasks() timed out. This is simpler and should be safe and
effective for all controllers.
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Cc: stable@vger.kernel.org
Reported-by: Kornel Dulęba <korneld@chromium.org>
Tested-by: Kornel Dulęba <korneld@chromium.org>
Co-developed-by: Kornel Dulęba <korneld@chromium.org>
Signed-off-by: Kornel Dulęba <korneld@chromium.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20231103084720.6886-7-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35597bdb04 ]
A correctly operating controller should successfully halt and clear tasks.
Failure may result in errors elsewhere, so promote messages from debug to
warnings.
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20231103084720.6886-6-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b578d5d18e ]
Failing to halt complicates the recovery. Additionally, unless the card or
controller are stuck, which is expected to be very rare, then the halt
should succeed, so it is better to wait. Set a large timeout.
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20231103084720.6886-3-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 174925d340 upstream.
During CQE error recovery, error-free data commands get requeued if there
is any data left to transfer, but non-data commands are completed even
though they have not been processed. Requeue them instead.
Note the only non-data command is cache flush, which would have resulted in
a cache flush being lost if it was queued at the time of CQE recovery.
Fixes: 1e8e55b670 ("mmc: block: Add CQE support")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20231103084720.6886-2-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57925e16c9 upstream.
For the t7 and older SoC families, the CMD_CFG_ERROR has no effect.
Starting from SoC family C3, setting this bit without SG LINK data
address will cause the controller to generate an IRQ and stop working.
To fix it, don't set the bit CMD_CFG_ERROR anymore.
Fixes: 18f92bc02f ("mmc: meson-gx: make sure the descriptor is stopped on errors")
Signed-off-by: Rong Chen <rong.chen@amlogic.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231026073156.2868310-1-rong.chen@amlogic.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 32a9cdb886 ]
tuning only support in 4-bit mode or 8 bit mode, so in 1-bit mode,
need to hold retuning.
Find this issue when use manual tuning method on imx93. When system
resume back, SDIO WIFI try to switch back to 4 bit mode, first will
trigger retuning, and all tuning command failed.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: dfa13ebbe3 ("mmc: host: Add facility to support re-tuning")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230830093922.3095850-1-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ebc581c3f ]
It looks like the original idea behind always doing a re-initialization of
a removable SDIO card during system resume in mmc_sdio_resume(), is to try
to play safe to detect whether the card has been removed.
However, this seems like a really a bad idea as it will most likely screw
things up, especially when the card is expected to remain powered on during
system suspend by the SDIO func driver.
Let's fix this, simply by trusting that the detect work checks if the card
is alive and inserted, which is being scheduled at the PM_POST_SUSPEND
notification anyway.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Stable-dep-of: 32a9cdb886 ("mmc: core: sdio: hold retuning if sdio in 1-bit mode")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 84ee19bffc upstream.
The OEMID is an 8-bit binary number rather than 16-bit as the current code
parses for. The OEMID occupies bits [111:104] in the CID register, see the
eMMC spec JESD84-B51 paragraph 7.2.3. It seems that the 16-bit comes from
the legacy MMC specs (v3.31 and before).
Let's fix the parsing by simply move to use 8-bit instead of 16-bit. This
means we ignore the impact on some of those old MMC cards that may be out
there, but on the other hand this shouldn't be a problem as the OEMID seems
not be an important feature for these cards.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230927071500.1791882-1-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4a5c59a95 upstream.
au1xmmc is split somewhat awkwardly into the main mmc subsystem driver,
and callbacks in platform_data that sit under arch/mips/ and are
always built in. The latter than call mmc_detect_change through
symbol_get. Remove the use of symbol_get by requiring the driver
to be built in. In the future the interrupt handlers for card
insert/eject detection should probably be moved into the main driver,
and which point it can be built modular again.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
[mcgrof: squashed in depends on MMC=y suggested by Arnd]
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b430d4ac9 upstream.
For a completed request, after the mmc_blk_mq_complete_rq(mq, req)
function is executed, the bitmap_tags corresponding to the
request will be cleared, that is, the request will be regarded as
idle. If the request is acquired by a different type of process at
this time, the issue_type of the request may change. It further
caused the value of mq->in_flight[issue_type] to be abnormal,
and a large number of requests could not be sent.
p1: p2:
mmc_blk_mq_complete_rq
blk_mq_free_request
blk_mq_get_request
blk_mq_rq_ctx_init
mmc_blk_mq_dec_in_flight
mmc_issue_type(mq, req)
This strategy can ensure the consistency of issue_type
before and after executing mmc_blk_mq_complete_rq.
Fixes: 81196976ed ("mmc: block: Add blk-mq support")
Cc: stable@vger.kernel.org
Signed-off-by: Yibin Ding <yibin.ding@unisoc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230802023023.1318134-1-yunlong.xing@unisoc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d830354337 upstream.
mmc_free_host() has already be called in wbsd_free_mmc(),
remove the mmc_free_host() in error path in wbsd_init().
Fixes: dc5b9b50fc ("mmc: wbsd: fix return value check of mmc_add_host()")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230807124443.3431366-1-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c2df53c580 ]
The driver overrides the error codes and IRQ0 returned by platform_get_irq()
to -EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the error
codes upstream. Since commit ce753ad154 ("platform: finally disallow IRQ0
in platform_get_irq() and its ilk") IRQ0 is no longer returned by those APIs,
so we now can safely ignore it...
Fixes: 2408a08583 ("mmc: sunxi-mmc: Handle return value of platform_get_irq")
Cc: stable@vger.kernel.org # v5.19+
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230617203622.6812-12-s.shtylyov@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71150ac125 ]
The driver overrides the error codes and IRQ0 returned by platform_get_irq()
to -EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the error
codes upstream. Since commit ce753ad154 ("platform: finally disallow IRQ0
in platform_get_irq() and its ilk") IRQ0 is no longer returned by those APIs,
so we now can safely ignore it...
Fixes: 660fc733bd ("mmc: bcm2835: Add new driver for the sdhost controller.")
Cc: stable@vger.kernel.org # v5.19+
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20230617203622.6812-2-s.shtylyov@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0196c8db83 ]
tmio_mmc_set_clock() is full of quirks because different SoC vendors
extended this in different ways.
The original IP defines the divisor range 1/2 ... 1/512.
bit 7 is set: 1/512
bit 6 is set: 1/256
...
bit 0 is set: 1/4
all bits clear: 1/2
It is platform-dependent how to achieve the 1/1 clock.
I guess the TMIO-MFD variant uses the clock selector outside of this IP,
as far as I see tmio_core_mmc_clk_div() in drivers/mfd/tmio_core.c
I guess bit[7:0]=0xff is Renesas-specific extension.
Socionext (and Panasonic) uses bit 10 (CLKSEL) for 1/1. Also, newer
versions of UniPhier SoC variants use bit 16 for 1/1024.
host->clk_update() is only used by the Renesas variants, whereas
host->set_clk_div() is only used by the TMIO-MFD variants.
To cope with this mess, promote tmio_mmc_set_clock() to a new
platform hook ->set_clock(), and melt the old two hooks into it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Stable-dep-of: 71150ac125 ("mmc: bcm2835: fix deferred probing")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83076d2268 ]
The spinlock is only used within the irq handler so it does not
seem very useful.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Stable-dep-of: 3c40eb8145 ("mmc: meson-gx: remove redundant mmc_request_done() call from irq context")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d442632221 upstream.
Conversion from big-endian to native is done in a common function
mmc_app_send_scr(). Converting in moxart_transfer_pio() is extra.
Double conversion on a LE system returns an incorrect SCR value,
leads to errors:
mmc0: unrecognised SCR structure version 8
Fixes: 1b66e94e6b ("mmc: moxart: Add MOXA ART SD/MMC driver")
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230627120549.2400325-1-saproj@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbfbddcddc upstream.
It seems that Micron MTFC4GACAJCN-1M despite advertising TRIM support does
not work when the core is trying to use REQ_OP_WRITE_ZEROES.
We are seeing the following errors in OpenWrt under 6.1 on Qnap Qhora 301W
that we did not previously have and tracked it down to REQ_OP_WRITE_ZEROES:
[ 18.085950] I/O error, dev loop0, sector 596 op 0x9:(WRITE_ZEROES) flags 0x800 phys_seg 0 prio class 2
Disabling TRIM makes the error go away, so lets add a quirk for this eMMC
to disable TRIM.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230530213259.1776512-1-robimarko@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1738a1f81 upstream.
It seems that Kingston EMMC04G-M627 despite advertising TRIM support does
not work when the core is trying to use REQ_OP_WRITE_ZEROES.
We are seeing I/O errors in OpenWrt under 6.1 on Zyxel NBG7815 that we did
not previously have and tracked it down to REQ_OP_WRITE_ZEROES.
Trying to use fstrim seems to also throw errors like:
[93010.835112] I/O error, dev loop0, sector 16902 op 0x3:(DISCARD) flags 0x800 phys_seg 1 prio class 2
Disabling TRIM makes the error go away, so lets add a quirk for this eMMC
to disable TRIM.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230619193621.437358-1-robimarko@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f649ab728 upstream.
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 413db49973 ]
The driver overrides the error codes returned by platform_get_irq_byname()
to -ENODEV, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating error
codes upstream.
Fixes: 9ec36cafe4 ("of/irq: do irq resolution in platform_get_irq")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20230617203622.6812-13-s.shtylyov@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b465dea5e1 ]
The driver overrides the error codes returned by platform_get_irq() to
-EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Fixes: 1b7ba57ecc ("mmc: sdhci-acpi: Handle return value of platform_get_irq")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230617203622.6812-9-s.shtylyov@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb51b74a57 ]
The driver overrides the error codes returned by platform_get_irq() to
-ENXIO, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Fixes: 9ec36cafe4 ("of/irq: do irq resolution in platform_get_irq")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20230617203622.6812-7-s.shtylyov@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aedf4ba1ad ]
The driver overrides the error codes returned by platform_get_irq() to
-ENXIO, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Fixes: 9ec36cafe4 ("of/irq: do irq resolution in platform_get_irq")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20230617203622.6812-6-s.shtylyov@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d84064da0 ]
The driver overrides the error codes returned by platform_get_irq() to
-ENXIO, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Fixes: 9ec36cafe4 ("of/irq: do irq resolution in platform_get_irq")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20230617203622.6812-5-s.shtylyov@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c4dc0f054 ]
The driver overrides the error codes returned by platform_get_irq() to
-EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Fixes: 208489032b ("mmc: mediatek: Add Mediatek MMC driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20230617203622.6812-4-s.shtylyov@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 003fb0a511 upstream.
Requests to the mmc layer usually come through a block device IO.
The exceptions are the ioctl interface, RPMB chardev ioctl
and debugfs, which issue their own blk_mq requests through
blk_execute_rq and do not query the BLK_STS error but the
mmcblk-internal drv_op_result. This patch ensures that drv_op_result
defaults to an error and has to be overwritten by the operation
to be considered successful.
The behavior leads to a bug where the request never propagates
the error, e.g. by directly erroring out at mmc_blk_mq_issue_rq if
mmc_blk_part_switch fails. The ioctl caller of the rpmb chardev then
can never see an error (BLK_STS_IOERR, but drv_op_result is unchanged)
and thus may assume that their call executed successfully when it did not.
While always checking the blk_execute_rq return value would be
advised, let's eliminate the error by always setting
drv_op_result as -EIO to be overwritten on success (or other error)
Fixes: 614f0388f5 ("mmc: block: move single ioctl() commands to block requests")
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/59c17ada35664b818b7bd83752119b2d@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a99d21cefd upstream.
We may get an empty response with zero length at the beginning of
the driver start and get following UBSAN error. Since there is no
content(SDRT_NONE) for the response, just return and skip the response
handling to avoid this problem.
Test pass : SDIO wifi throughput test with this patch
[ 126.980684] UBSAN: array-index-out-of-bounds in drivers/mmc/host/vub300.c:1719:12
[ 126.980709] index -1 is out of range for type 'u32 [4]'
[ 126.980729] CPU: 4 PID: 9 Comm: kworker/u16:0 Tainted: G E 6.3.0-rc4-mtk-local-202304272142 #1
[ 126.980754] Hardware name: Intel(R) Client Systems NUC8i7BEH/NUC8BEB, BIOS BECFL357.86A.0081.2020.0504.1834 05/04/2020
[ 126.980770] Workqueue: kvub300c vub300_cmndwork_thread [vub300]
[ 126.980833] Call Trace:
[ 126.980845] <TASK>
[ 126.980860] dump_stack_lvl+0x48/0x70
[ 126.980895] dump_stack+0x10/0x20
[ 126.980916] ubsan_epilogue+0x9/0x40
[ 126.980944] __ubsan_handle_out_of_bounds+0x70/0x90
[ 126.980979] vub300_cmndwork_thread+0x58e7/0x5e10 [vub300]
[ 126.981018] ? _raw_spin_unlock+0x18/0x40
[ 126.981042] ? finish_task_switch+0x175/0x6f0
[ 126.981070] ? __switch_to+0x42e/0xda0
[ 126.981089] ? __switch_to_asm+0x3a/0x80
[ 126.981129] ? __pfx_vub300_cmndwork_thread+0x10/0x10 [vub300]
[ 126.981174] ? __kasan_check_read+0x11/0x20
[ 126.981204] process_one_work+0x7ee/0x13d0
[ 126.981246] worker_thread+0x53c/0x1240
[ 126.981291] kthread+0x2b8/0x370
[ 126.981312] ? __pfx_worker_thread+0x10/0x10
[ 126.981336] ? __pfx_kthread+0x10/0x10
[ 126.981359] ret_from_fork+0x29/0x50
[ 126.981400] </TASK>
Fixes: 88095e7b47 ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/048cd6972c50c33c2e8f81d5228fed928519918b.1683987673.git.deren.wu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eca5bd666b ]
This commit fixes a race between completion of stop command and start of a
new command.
Previously the command ready interrupt was enabled before stop command
was written to the command register. This caused the command ready
interrupt to fire immediately since the CMDRDY flag is asserted constantly
while there is no command in progress.
Consequently the command state machine will immediately advance to the
next state when the tasklet function is executed again, no matter
actual completion state of the stop command.
Thus a new command can then be dispatched immediately, interrupting and
corrupting the stop command on the CMD line.
Fix that by dropping the command ready interrupt enable before calling
atmci_send_stop_cmd. atmci_send_stop_cmd does already enable the
command ready interrupt, no further writes to ATMCI_IER are necessary.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20221230194315.809903-2-t.schramm@manjaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 605d9fb955 upstream.
If sdio_add_func() or sdio_init_func() fails, sdio_remove_func() can
not release the resources, because the sdio function is not presented
in these two cases, it won't call of_node_put() or put_device().
To fix these leaks, make sdio_func_present() only control whether
device_del() needs to be called or not, then always call of_node_put()
and put_device().
In error case in sdio_init_func(), the reference of 'card->dev' is
not get, to avoid redundant put in sdio_free_func_cis(), move the
get_device() to sdio_alloc_func() and put_device() to sdio_release_func(),
it can keep the get/put function be balanced.
Without this patch, while doing fault inject test, it can get the
following leak reports, after this fix, the leak is gone.
unreferenced object 0xffff888112514000 (size 2048):
comm "kworker/3:2", pid 65, jiffies 4294741614 (age 124.774s)
hex dump (first 32 bytes):
00 e0 6f 12 81 88 ff ff 60 58 8d 06 81 88 ff ff ..o.....`X......
10 40 51 12 81 88 ff ff 10 40 51 12 81 88 ff ff .@Q......@Q.....
backtrace:
[<000000009e5931da>] kmalloc_trace+0x21/0x110
[<000000002f839ccb>] mmc_alloc_card+0x38/0xb0 [mmc_core]
[<0000000004adcbf6>] mmc_sdio_init_card+0xde/0x170 [mmc_core]
[<000000007538fea0>] mmc_attach_sdio+0xcb/0x1b0 [mmc_core]
[<00000000d4fdeba7>] mmc_rescan+0x54a/0x640 [mmc_core]
unreferenced object 0xffff888112511000 (size 2048):
comm "kworker/3:2", pid 65, jiffies 4294741623 (age 124.766s)
hex dump (first 32 bytes):
00 40 51 12 81 88 ff ff e0 58 8d 06 81 88 ff ff .@Q......X......
10 10 51 12 81 88 ff ff 10 10 51 12 81 88 ff ff ..Q.......Q.....
backtrace:
[<000000009e5931da>] kmalloc_trace+0x21/0x110
[<00000000fcbe706c>] sdio_alloc_func+0x35/0x100 [mmc_core]
[<00000000c68f4b50>] mmc_attach_sdio.cold.18+0xb1/0x395 [mmc_core]
[<00000000d4fdeba7>] mmc_rescan+0x54a/0x640 [mmc_core]
Fixes: 3d10a1ba0d ("sdio: fix reference counting in sdio_remove_func()")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230130125808.3471254-1-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8509419758 upstream.
If the controller is suspended by runtime PM, the clock is already
disabled, so do not try to disable it again during removal. Use
pm_runtime_disable() to flush any pending runtime PM transitions.
Fixes: 9a8e1e8cc2 ("mmc: sunxi: Add runtime_pm support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220810022509.43743-1-samuel@sholland.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit aae9d3a440 ]
There is a case where the timeout clock is not supplied to the capability.
Add a quirk for that.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Link: https://lore.kernel.org/r/20221111081033.3813-7-hayashi.kunihiko@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b38a20f29a ]
mmc_add_host() may return error, if we ignore its return value,
it will lead two issues:
1. The memory that allocated in mmc_alloc_host() is leaked.
2. In the remove() path, mmc_remove_host() will be called to
delete device, but it's not added yet, it will lead a kernel
crash because of null-ptr-deref in device_del().
So fix this by checking the return value and goto error path which
will call mmc_free_host().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221109133539.3275664-1-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc5b9b50fc ]
mmc_add_host() may return error, if we ignore its return value,
it will lead two issues:
1. The memory that allocated in mmc_alloc_host() is leaked.
2. In the remove() path, mmc_remove_host() will be called to
delete device, but it's not added yet, it will lead a kernel
crash because of null-ptr-deref in device_del().
So fix this by checking the return value and goto error path which
will call mmc_free_host(), besides, other resources also need be
released.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221109133237.3273558-1-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
