Avoid data corruption by rejecting pass-through commands where
T_LENGTH is zero (No data is transferred) and the dma direction
is not DMA_NONE.
Cc: <stable@vger.kernel.org>
Reported-by: syzkaller<syzkaller@googlegroups.com>
Signed-off-by: George Kennedy<george.kennedy@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
The ASMedia 1092 has a configuration mode which will present a
dummy device; sadly the implementation falsely claims to provide
a device with 100M which doesn't actually exist.
So disable this device to avoid errors during boot.
Cc: stable@vger.kernel.org
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
ATA IDENTIFY command returns an array of le16 words. Accessing it as a
u16 array triggers the following sparse warning:
drivers/ata/ahci_ceva.c:107:33: warning: invalid assignment: &=
drivers/ata/ahci_ceva.c:107:33: left side has type unsigned short
drivers/ata/ahci_ceva.c:107:33: right side has type restricted __le16
Use a local variable to explicitly cast the id array to __le16 to avoid
this warning.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
coccinelle report：
./drivers/ata/libata-sata.c:830:8-16:
WARNING: use scnprintf or sprintf
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Guang <yang.guang5@zte.com.cn>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Trying to remove the fsl-sata module in the PPC64 GNU/Linux
leads to the following warning:
------------[ cut here ]------------
remove_proc_entry: removing non-empty directory 'irq/69',
leaking at least 'fsl-sata[ff0221000.sata]'
WARNING: CPU: 3 PID: 1048 at fs/proc/generic.c:722
.remove_proc_entry+0x20c/0x220
IRQMASK: 0
NIP [c00000000033826c] .remove_proc_entry+0x20c/0x220
LR [c000000000338268] .remove_proc_entry+0x208/0x220
Call Trace:
.remove_proc_entry+0x208/0x220 (unreliable)
.unregister_irq_proc+0x104/0x140
.free_desc+0x44/0xb0
.irq_free_descs+0x9c/0xf0
.irq_dispose_mapping+0x64/0xa0
.sata_fsl_remove+0x58/0xa0 [sata_fsl]
.platform_drv_remove+0x40/0x90
.device_release_driver_internal+0x160/0x2c0
.driver_detach+0x64/0xd0
.bus_remove_driver+0x70/0xf0
.driver_unregister+0x38/0x80
.platform_driver_unregister+0x14/0x30
.fsl_sata_driver_exit+0x18/0xa20 [sata_fsl]
---[ end trace 0ea876d4076908f5 ]---
The driver creates the mapping by calling irq_of_parse_and_map(),
so it also has to dispose the mapping. But the easy way out is to
simply use platform_get_irq() instead of irq_of_parse_map(). Also
we should adapt return value checking and propagate error values.
In this case the mapping is not managed by the device but by
the of core, so the device has not to dispose the mapping.
Fixes: faf0b2e5af ("drivers/ata: add support to Freescale 3.0Gbps SATA Controller")
Cc: stable@vger.kernel.org
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
When the `rmmod sata_fsl.ko` command is executed in the PPC64 GNU/Linux,
a bug is reported:
==================================================================
BUG: Unable to handle kernel data access on read at 0x80000800805b502c
Oops: Kernel access of bad area, sig: 11 [#1]
NIP [c0000000000388a4] .ioread32+0x4/0x20
LR [80000000000c6034] .sata_fsl_port_stop+0x44/0xe0 [sata_fsl]
Call Trace:
.free_irq+0x1c/0x4e0 (unreliable)
.ata_host_stop+0x74/0xd0 [libata]
.release_nodes+0x330/0x3f0
.device_release_driver_internal+0x178/0x2c0
.driver_detach+0x64/0xd0
.bus_remove_driver+0x70/0xf0
.driver_unregister+0x38/0x80
.platform_driver_unregister+0x14/0x30
.fsl_sata_driver_exit+0x18/0xa20 [sata_fsl]
.__se_sys_delete_module+0x1ec/0x2d0
.system_call_exception+0xfc/0x1f0
system_call_common+0xf8/0x200
==================================================================
The triggering of the BUG is shown in the following stack:
driver_detach
device_release_driver_internal
__device_release_driver
drv->remove(dev) --> platform_drv_remove/platform_remove
drv->remove(dev) --> sata_fsl_remove
iounmap(host_priv->hcr_base); <---- unmap
kfree(host_priv); <---- free
devres_release_all
release_nodes
dr->node.release(dev, dr->data) --> ata_host_stop
ap->ops->port_stop(ap) --> sata_fsl_port_stop
ioread32(hcr_base + HCONTROL) <---- UAF
host->ops->host_stop(host)
The iounmap(host_priv->hcr_base) and kfree(host_priv) functions should
not be executed in drv->remove. These functions should be executed in
host_stop after port_stop. Therefore, we move these functions to the
new function sata_fsl_host_stop and bind the new function to host_stop.
Fixes: faf0b2e5af ("drivers/ata: add support to Freescale 3.0Gbps SATA Controller")
Cc: stable@vger.kernel.org
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
The zero day bot reported some sparse complaints in pata_falcon.c. E.g.
drivers/ata/pata_falcon.c:58:41: warning: cast removes address space '__iomem' of expression
drivers/ata/pata_falcon.c:58:41: warning: incorrect type in argument 1 (different address spaces)
drivers/ata/pata_falcon.c:58:41: expected unsigned short volatile [noderef] [usertype] __iomem *port
drivers/ata/pata_falcon.c:58:41: got unsigned short [usertype] *
The same thing shows up in 8 places, all told. Avoid this by removing
unnecessary type casts.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Since ata_ncq_sdev_attrs is a local struct, declare it static. This
avoids a sparse warning at compile time.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
The StorageD3Enable _DSD is used for the vendor to indicate that the disk
should be opted into or out of a different behavior based upon the platform
design.
For AMD's Renoir and Green Sardine platforms it's important that any
attached SATA storage has transitioned into DevSlp when s2idle is used.
If the disk is left in active/partial/slumber, then the system is not able
to resume properly.
When the StorageD3Enable _DSD is detected, check the system is using s2idle
and DevSlp is enabled and if so explicitly wait long enough for the disk to
enter DevSlp.
Cc: Nehal-bakulchandra Shah <Nehal-bakulchandra.Shah@amd.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214091
Link: https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/power-management-for-storage-hardware-devices-intro
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
AMD requires that the SATA controller be configured for devsleep in order
for S0i3 entry to work properly.
commit b1a9585cc3 ("ata: ahci: Enable DEVSLP by default on x86 with
SLP_S0") sets up a kernel policy to enable devsleep on Intel mobile
platforms that are using s0ix. Add the PCI ID for the SATA controller in
Green Sardine platforms to extend this policy by default for AMD based
systems using s0i3 as well.
Cc: Nehal-bakulchandra Shah <Nehal-bakulchandra.Shah@amd.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214091
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
ata_dev_config_ncq_prio() and ata_dev_config_devslp() both access pages
of the IDENTIFY DEVICE data log. Before calling ata_read_log_page(),
make sure to check for the existence of the IDENTIFY DEVICE data log and
of the log page accessed using ata_identify_page_supported(). This
avoids useless error messages from ata_read_log_page() and failures with
some LLDD scsi drivers using libsas.
Reported-by: Nikolay <knv418@gmail.com>
Cc: stable@kernel.org # 5.15
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Tested-by: Matthew Perkowski <mgperkow@gmail.com>
If ata_read_log_page() fails to read a log page, the ata_dev_err() error
message only print the page number, omitting the log number. In case of
error, facilitate debugging by also printing the log number.
Cc: stable@kernel.org # 5.15
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Tested-by: Matthew Perkowski <mgperkow@gmail.com>
ahci_shost_attr_group is referenced only in drivers/ata/libahci.c.
Declare it as static.
Fixes: c3f69c7f62 ("scsi: ata: Switch to attribute groups")
Cc: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
ACS-3 introduced the ATA Identify Device Data log as mandatory. A
warning message currently signals to the user if a device does not
report supporting this log page in the log directory page, regardless
of the ATA version of the device. Furthermore, this warning will appear
for all attempts at accessing this missing log page during device
revalidation.
Since it is useless to constantly access the log directory and warn
about this lack of support once we have discovered that the device
does not support this log page, introduce the horkage flag
ATA_HORKAGE_NO_ID_DEV_LOG to mark a device as lacking support for
the Identify Device Data log page. Set this flag when
ata_log_supported() returns false in ata_identify_page_supported().
The warning is printed only if the device ATA level is 10 or above
(ACS-3 or above), and only once on device scan. With this flag set, the
log directory page is not accessed again to test for Identify Device
Data log page support.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
The print function dev_err() is redundant because
platform_get_irq() already prints an error.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Some ATA drives are very slow to respond to READ_LOG_EXT and
READ_LOG_DMA_EXT commands issued from ata_dev_configure() when the
device is revalidated right after resuming a system or inserting the
ATA adapter driver (e.g. ahci). The default 5s timeout
(ATA_EH_CMD_DFL_TIMEOUT) used for these commands is too short, causing
errors during the device configuration. Ex:
...
ata9: SATA max UDMA/133 abar m524288@0x9d200000 port 0x9d200400 irq 209
ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata9.00: ATA-9: XXX XXXXXXXXXXXXXXX, XXXXXXXX, max UDMA/133
ata9.00: qc timeout (cmd 0x2f)
ata9.00: Read log page 0x00 failed, Emask 0x4
ata9.00: Read log page 0x00 failed, Emask 0x40
ata9.00: NCQ Send/Recv Log not supported
ata9.00: Read log page 0x08 failed, Emask 0x40
ata9.00: 27344764928 sectors, multi 16: LBA48 NCQ (depth 32), AA
ata9.00: Read log page 0x00 failed, Emask 0x40
ata9.00: ATA Identify Device Log not supported
ata9.00: failed to set xfermode (err_mask=0x40)
ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata9.00: configured for UDMA/133
...
The timeout error causes a soft reset of the drive link, followed in
most cases by a successful revalidation as that give enough time to the
drive to become fully ready to quickly process the read log commands.
However, in some cases, this also fails resulting in the device being
dropped.
Fix this by using adding the ata_eh_revalidate_timeouts entries for the
READ_LOG_EXT and READ_LOG_DMA_EXT commands. This defines a timeout
increased to 15s, retriable one time.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
This series consists of the usual driver updates (ufs, smartpqi, lpfc,
target, megaraid_sas, hisi_sas, qla2xxx) and minor updates and bug
fixes. Notable core changes are the removal of scsi->tag which caused
some churn in obsolete drivers and a sweep through all drivers to call
scsi_done() directly instead of scsi->done() which removes a pointer
indirection from the hot path and a move to register core sysfs files
earlier, which means they're available to KOBJ_ADD processing, which
necessitates switching all drivers to using attribute groups.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYYUfBCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbUJAQDZt4oc
vUx9JpyrdHxxTCuOzVFd8W1oJn0k5ltCBuz4yAD8DNbGhGm93raMSJ3FOOlzLEbP
RG8vBdpxMudlvxAPi/A=
=BSFz
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This consists of the usual driver updates (ufs, smartpqi, lpfc,
target, megaraid_sas, hisi_sas, qla2xxx) and minor updates and bug
fixes.
Notable core changes are the removal of scsi->tag which caused some
churn in obsolete drivers and a sweep through all drivers to call
scsi_done() directly instead of scsi->done() which removes a pointer
indirection from the hot path and a move to register core sysfs files
earlier, which means they're available to KOBJ_ADD processing, which
necessitates switching all drivers to using attribute groups"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (279 commits)
scsi: lpfc: Update lpfc version to 14.0.0.3
scsi: lpfc: Allow fabric node recovery if recovery is in progress before devloss
scsi: lpfc: Fix link down processing to address NULL pointer dereference
scsi: lpfc: Allow PLOGI retry if previous PLOGI was aborted
scsi: lpfc: Fix use-after-free in lpfc_unreg_rpi() routine
scsi: lpfc: Correct sysfs reporting of loop support after SFP status change
scsi: lpfc: Wait for successful restart of SLI3 adapter during host sg_reset
scsi: lpfc: Revert LOG_TRACE_EVENT back to LOG_INIT prior to driver_resource_setup()
scsi: ufs: ufshcd-pltfrm: Fix memory leak due to probe defer
scsi: ufs: mediatek: Avoid sched_clock() misuse
scsi: mpt3sas: Make mpt3sas_dev_attrs static
scsi: scsi_transport_sas: Add 22.5 Gbps link rate definitions
scsi: target: core: Stop using bdevname()
scsi: aha1542: Use memcpy_{from,to}_bvec()
scsi: sr: Add error handling support for add_disk()
scsi: sd: Add error handling support for add_disk()
scsi: target: Perform ALUA group changes in one step
scsi: target: Replace lun_tg_pt_gp_lock with rcu in I/O path
scsi: target: Fix alua_tg_pt_gps_count tracking
scsi: target: Fix ordered tag handling
...
Changes in libata for 5.16 include the following:
* Remove duplicated AHCI adapter PCI device IDs (from Krzysztof)
* Cleanup of device DMA state checking to consistantly use
ata_dma_enabled() (from Reimar)
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSRPv8tYSvhwAzJdzjdoc3SxdoYdgUCYYDUiwAKCRDdoc3SxdoY
dgcUAP9G6Bf5Yar37Nd+2eoROAh01jkc4J2ez0p/pr+kDlp0MQD/f6Cfj1oFpoqn
kZXd3dIyf6uOtkJRXbyc1YLMzdr8Xw8=
=EaHo
-----END PGP SIGNATURE-----
Merge tag 'libata-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull libata updates from Damien Le Moal:
- Remove duplicated AHCI adapter PCI device IDs (from Krzysztof)
- Cleanup of device DMA state checking to consistantly use
ata_dma_enabled() (from Reimar)
* tag 'libata-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
pata_radisys: fix checking of DMA state
pata_optidma: fix checking of DMA state
pata_amd: fix checking of DMA state
pata_ali: fix checking of DMA state
libata-scsi: fix checking of DMA state
libata: fix checking of DMA state
Add AHCI support for ASM1062+JBM575 cards
ahci: remove duplicated PCI device IDs
-----BEGIN PGP SIGNATURE-----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=w6Kz
-----END PGP SIGNATURE-----
Merge tag 'for-5.16/scsi-ma-2021-10-29' of git://git.kernel.dk/linux-block
Pull SCSI multi-actuator support from Jens Axboe:
"This adds SCSI support for the recently merged block multi-actuator
support. Since this was sitting on top of the block tree, the SCSI
side asked me to queue it up."
* tag 'for-5.16/scsi-ma-2021-10-29' of git://git.kernel.dk/linux-block:
doc: Fix typo in request queue sysfs documentation
doc: document sysfs queue/independent_access_ranges attributes
libata: support concurrent positioning ranges log
scsi: sd: add concurrent positioning ranges support
Add support to discover if an ATA device supports the Concurrent
Positioning Ranges data log (address 0x47), indicating that the device
is capable of seeking to multiple different locations in parallel using
multiple actuators serving different LBA ranges.
Also add support to translate the concurrent positioning ranges log
into its equivalent Concurrent Positioning Ranges VPD page B9h in
libata-scsi.c.
The format of the Concurrent Positioning Ranges Log is defined in ACS-5
r9.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Link: https://lore.kernel.org/r/20211027022223.183838-4-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
mv_init_host() propagates the value returned by mv_chip_id() which in turn
gets propagated by mv_pci_init_one() and hits local_pci_probe().
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Since this is a bug rather than a recoverable runtime error we should
use dev_alert() instead of dev_err().
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
struct device supports attribute groups directly but does not support
struct device_attribute directly. Hence switch to attribute groups.
Link: https://lore.kernel.org/r/20211012233558.4066756-3-bvanassche@acm.org
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Conditional statements are faster than indirect calls. Hence call
scsi_done() directly.
Link: https://lore.kernel.org/r/20211007202923.2174984-4-bvanassche@acm.org
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I got a null-ptr-deref report:
KASAN: null-ptr-deref in range [0x0000000000000090-0x0000000000000097]
...
RIP: 0010:regulator_enable+0x84/0x260
...
Call Trace:
ahci_platform_enable_regulators+0xae/0x320
ahci_platform_enable_resources+0x1a/0x120
ahci_probe+0x4f/0x1b9
platform_probe+0x10b/0x280
...
entry_SYSCALL_64_after_hwframe+0x44/0xae
If devm_regulator_get() in ahci_platform_get_resources() fails,
hpriv->phy_regulator will point to NULL, when enabling or disabling it,
null-ptr-deref will occur.
ahci_probe()
ahci_platform_get_resources()
devm_regulator_get(, "phy") // failed, let phy_regulator = NULL
ahci_platform_enable_resources()
ahci_platform_enable_regulators()
regulator_enable(hpriv->phy_regulator) // null-ptr-deref
commit 962399bb7f ("ata: libahci_platform: Fix regulator_get_optional()
misuse") replaces devm_regulator_get_optional() with devm_regulator_get(),
but PHY regulator omits to delete "hpriv->phy_regulator = NULL;" like AHCI.
Delete it like AHCI regulator to fix this bug.
Fixes: commit 962399bb7f ("ata: libahci_platform: Fix regulator_get_optional() misuse")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Checking if DMA is enabled should be done via the
ata_dma_enabled helper function, since the init state
0xff indicates disabled.
Change based on code review, not tested due to lack of hardware.
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Checking if DMA is enabled should be done via the
ata_dma_enabled helper function, since the init state
0xff indicates disabled.
Change based on code review, not tested due to lack of hardware.
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Checking if DMA is enabled should be done via the
ata_dma_enabled helper function, since the init state
0xff indicates disabled.
Change based on code review, not tested due to lack of hardware.
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Checking if DMA is enabled should be done via the
ata_dma_enabled helper function, since the init state
0xff indicates disabled.
Change based on code review, not tested due to lack of hardware.
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Checking if DMA is enabled should be done via the
ata_dma_enabled helper function, since the init state
0xff indicates disabled.
Change based on code review, not tested due to lack of hardware.
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Checking if DMA is enabled should be done via the
ata_dma_enabled helper function, since the init state
0xff indicates disabled.
This meant that ATA_CMD_READ_LOG_DMA_EXT was used and probed
for before DMA was enabled, which caused hangs for some combinations
of controllers and devices.
It might also have caused it to be incorrectly disabled as broken,
but there have been no reports of that.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=195895
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Add support for PCIe SATA expander cards based on ASMedia 1062 + JBM575
controllers.
These cards can provide up to 10 or more SATA ports on one PCIe card.
Signed-off-by: István Pongrácz <pongracz.istvan@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
The last byte of "pad" is used without being initialized.
Fixes: 55dba3120f ("libata: update ->data_xfer hook for ATAPI")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Intel devices 0x2822, 0x2823, 0x2826 and 0x2827 are already on the list
as Lewisburg AHCI/RAID. They use same configuration except 0x2822 which
has board_ahci_nosntf (for ICH8).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Many users are reporting that the Samsung 860 and 870 SSD are having
various issues when combined with AMD/ATI (vendor ID 0x1002) SATA
controllers and only completely disabling NCQ helps to avoid these
issues.
Always disabling NCQ for Samsung 860/870 SSDs regardless of the host
SATA adapter vendor will cause I/O performance degradation with well
behaved adapters. To limit the performance impact to ATI adapters,
introduce the ATA_HORKAGE_NO_NCQ_ON_ATI flag to force disable NCQ
only for these adapters.
Also, two libata.force parameters (noncqati and ncqati) are introduced
to disable and enable the NCQ for the system which equipped with ATI
SATA adapter and Samsung 860 and 870 SSDs. The user can determine NCQ
function to be enabled or disabled according to the demand.
After verifying the chipset from the user reports, the issue appears
on AMD/ATI SB7x0/SB8x0/SB9x0 SATA Controllers and does not appear on
recent AMD SATA adapters. The vendor ID of ATI should be 0x1002.
Therefore, ATA_HORKAGE_NO_NCQ_ON_AMD was modified to
ATA_HORKAGE_NO_NCQ_ON_ATI.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201693
Signed-off-by: Kate Hsuan <hpa@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210903094411.58749-1-hpa@redhat.com
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit ca6bfcb2f6 ("libata: Enable queued TRIM for Samsung SSD 860")
limited the existing ATA_HORKAGE_NO_NCQ_TRIM quirk from "Samsung SSD 8*",
covering all Samsung 800 series SSDs, to only apply to "Samsung SSD 840*"
and "Samsung SSD 850*" series based on information from Samsung.
But there is a large number of users which is still reporting issues
with the Samsung 860 and 870 SSDs combined with Intel, ASmedia or
Marvell SATA controllers and all reporters also report these problems
going away when disabling queued trims.
Note that with AMD SATA controllers users are reporting even worse
issues and only completely disabling NCQ helps there, this will be
addressed in a separate patch.
Fixes: ca6bfcb2f6 ("libata: Enable queued TRIM for Samsung SSD 860")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203475
Cc: stable@vger.kernel.org
Cc: Kate Hsuan <hpa@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20210823095220.30157-1-hdegoede@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This series consists of the usual driver updates (ufs, qla2xxx,
target, smartpqi, lpfc, mpt3sas). The core change causing the most
churn was replacing the command request field request with a macro,
allowing us to offset map to it and remove the redundant field; the
same was also done for the tag field. The most impactful change is
the final removal of scsi_ioctl, which has been deprecated for over a
decade.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYTD/TiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdUkAQCjb3Ux
4K9438mMelHlzM4er1S1IJ0WNnvObaVMNO9LBwD+JUz+rHsrKvuEX9j3g3C3u6JH
hC3BUEW8f2LLnujWanQ=
=lC5o
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series consists of the usual driver updates (ufs, qla2xxx,
target, smartpqi, lpfc, mpt3sas).
The core change causing the most churn was replacing the command
request field request with a macro, allowing us to offset map to it
and remove the redundant field; the same was also done for the tag
field.
The most impactful change is the final removal of scsi_ioctl, which
has been deprecated for over a decade"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (293 commits)
scsi: ufs: Fix ufshcd_request_sense_async() for Samsung KLUFG8RHDA-B2D1
scsi: ufs: ufs-exynos: Fix static checker warning
scsi: mpt3sas: Use the proper SCSI midlayer interfaces for PI
scsi: lpfc: Use the proper SCSI midlayer interfaces for PI
scsi: lpfc: Copyright updates for 14.0.0.1 patches
scsi: lpfc: Update lpfc version to 14.0.0.1
scsi: lpfc: Add bsg support for retrieving adapter cmf data
scsi: lpfc: Add cmf_info sysfs entry
scsi: lpfc: Add debugfs support for cm framework buffers
scsi: lpfc: Add support for maintaining the cm statistics buffer
scsi: lpfc: Add rx monitoring statistics
scsi: lpfc: Add support for the CM framework
scsi: lpfc: Add cmfsync WQE support
scsi: lpfc: Add support for cm enablement buffer
scsi: lpfc: Add cm statistics buffer support
scsi: lpfc: Add EDC ELS support
scsi: lpfc: Expand FPIN and RDF receive logging
scsi: lpfc: Add MIB feature enablement support
scsi: lpfc: Add SET_HOST_DATA mbox cmd to pass date/time info to firmware
scsi: fc: Add EDC ELS definition
...
These are updates for drivers that are tied to a particular SoC,
including the correspondig device tree bindings:
- A couple of reset controller changes for unisoc, uniphier, renesas
and zte platforms
- memory controller driver fixes for omap and tegra
- Rockchip io domain driver updates
- Lots of updates for qualcomm platforms, mostly touching their
firmware and power management drivers
- Tegra FUSE and firmware driver updateѕ
- Support for virtio transports in the SCMI firmware framework
- cleanup of ixp4xx drivers, towards enabling multiplatform
support and bringing it up to date with modern platforms
- Minor updates for keystone, mediatek, omap, renesas.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iD8DBQBhLz215t5GS2LDRf4RAjlHAJ473D0PymaTzv68EuPHThG+DEPifQCdGjLq
QGBB6JidIP8rtEdC+LWBB8I=
=M5+N
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are updates for drivers that are tied to a particular SoC,
including the correspondig device tree bindings:
- A couple of reset controller changes for unisoc, uniphier, renesas
and zte platforms
- memory controller driver fixes for omap and tegra
- Rockchip io domain driver updates
- Lots of updates for qualcomm platforms, mostly touching their
firmware and power management drivers
- Tegra FUSE and firmware driver updateѕ
- Support for virtio transports in the SCMI firmware framework
- cleanup of ixp4xx drivers, towards enabling multiplatform support
and bringing it up to date with modern platforms
- Minor updates for keystone, mediatek, omap, renesas"
* tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (96 commits)
reset: simple: remove ZTE details in Kconfig help
soc: rockchip: io-domain: Remove unneeded semicolon
soc: rockchip: io-domain: add rk3568 support
dt-bindings: power: add rk3568-pmu-io-domain support
bus: ixp4xx: return on error in ixp4xx_exp_probe()
soc: renesas: Prefer memcpy() over strcpy()
firmware: tegra: Stop using seq_get_buf()
soc/tegra: fuse: Enable fuse clock on suspend for Tegra124
soc/tegra: fuse: Add runtime PM support
soc/tegra: fuse: Clear fuse->clk on driver probe failure
soc/tegra: pmc: Prevent racing with cpuilde driver
soc/tegra: bpmp: Remove unused including <linux/version.h>
dt-bindings: soc: ti: pruss: Add dma-coherent property
soc: ti: Remove pm_runtime_irq_safe() usage for smartreflex
soc: ti: pruss: Enable support for ICSSG subsystems on K3 AM64x SoCs
dt-bindings: soc: ti: pruss: Update bindings for K3 AM64x SoCs
firmware: arm_scmi: Use WARN_ON() to check configured transports
firmware: arm_scmi: Fix boolconv.cocci warnings
soc: mediatek: mmsys: Fix missing UFOE component in mt8173 table routing
soc: mediatek: mmsys: add MT8365 support
...
Currently, the only way a user can determine if a SATA device supports
NCQ priority is to try to enable the use of this feature using the
ncq_prio_enable sysfs device attribute. If enabling the feature fails,
it is because the device does not support NCQ priority. Otherwise, the
feature is enabled and success indicates that the device supports NCQ
priority.
Improve this odd interface by introducing the read-only
ncq_prio_supported sysfs device attribute to indicate if a SATA device
supports NCQ priority. The value of this attribute reflects the status
of device flag ATA_DFLAG_NCQ_PRIO, which is set only for devices
supporting NCQ priority.
Add this new sysfs attribute to the device attributes group of libahci
and libata-sata.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Link: https://lore.kernel.org/r/20210816014456.2191776-10-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Print a list of features supported by a drive when it is configured in
ata_dev_configure() using the new function ata_dev_print_features().
The features printed are not already advertized and are: trusted
send-recev support, device attention support, device sleep support,
NCQ send-recv support and NCQ priority support.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20210816014456.2191776-9-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Support for the READ LOG PAGE DMA EXT command is indicated by words 119
and 120 of a device identify data. This is tested in
ata_read_log_page() with ata_id_has_read_log_dma_ext() and the
READ LOG PAGE DMA command used if the device reports supports for it.
However, some devices lie about this support and using the DMA version
of the command fails, generating the warning message "READ LOG DMA EXT
failed, trying PIO". Since READ LOG PAGE DMA EXT is an optional command,
this warning is not at all important but may be scary for the user.
Change ata_read_log_page() to suppres this warning and to print an
error message if both DMA and PIO attempts failed.
With this change, there is no need to print again an error message when
ata_read_log_page() returns an error. So simplify the users of this
function.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20210816014456.2191776-8-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The ata device flag ATA_DFLAG_NCQ_PRIO indicates if a device supports
the NCQ Priority feature while the ATA_DFLAG_NCQ_PRIO_ENABLE device
flag indicates if the feature is enabled. Enabling NCQ priority use is
controlled by the user through the device sysfs attribute
ncq_prio_enable. As a result, the ATA_DFLAG_NCQ_PRIO flag should not be
cleared when ATA_DFLAG_NCQ_PRIO_ENABLE is not set as the device still
supports the feature even after the user disables it. This leads to the
following cleanups:
- In ata_build_rw_tf(), set a command high priority bit based on the
ATA_DFLAG_NCQ_PRIO_ENABLE flag, not on the ATA_DFLAG_NCQ flag. That
is, set a command high priority only if the user enabled NCQ priority
use.
- In ata_dev_config_ncq_prio(), ATA_DFLAG_NCQ_PRIO should not be cleared
if ATA_DFLAG_NCQ_PRIO_ENABLE is not set. If the device does not
support NCQ priority, both ATA_DFLAG_NCQ_PRIO and
ATA_DFLAG_NCQ_PRIO_ENABLE must be cleared.
With the above ata_dev_config_ncq_prio() change, ATA_DFLAG_NCQ_PRIO flag
is set on device scan and revalidation. There is no need to trigger a
device revalidation in ata_ncq_prio_enable_store() when the user enables
the use of NCQ priority. Remove the revalidation code from that funciton
to simplify it. Also change the return value from -EIO to -EINVAL when a
user tries to enable NCQ priority for a device that does not support
this feature. While at it, also simplify ata_ncq_prio_enable_show().
Overall, there is no functional change introduced by this patch.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20210816014456.2191776-7-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Introduce the helper functions ata_dev_config_lba() and
ata_dev_config_chs() to configure the addressing capabilities of a
device. To control message printing in these new helpers, as well as
in ata_dev_configure() and in ata_hpa_resize(), add the helper function
ata_dev_print_info() to avoid open coding for the eh context
ATA_EHI_PRINTINFO flag in multiple functions.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20210816014456.2191776-6-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the code to retrieve the device sleep capability and timings out of
ata_dev_configure() into the helper function ata_dev_config_devslp().
While at it, mark the device as supporting the device sleep capability
only if the sata settings page was retrieved successfully to ensure that
the timing information is correctly initialized.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20210816014456.2191776-5-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Sparse complains about context imbalance in ata_scsi_rbuf_get() and
ata_scsi_rbuf_put() due to these functions respectively only taking
and releasing the ata_scsi_rbuf_lock spinlock. Since these functions are
only called from ata_scsi_rbuf_fill() with ata_scsi_rbuf_get() being
called with a copy_in argument always false, the code can be simplified
and ata_scsi_rbuf_{get|put} removed. This change both simplifies the
code and fixes the sparse warning.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20210816014456.2191776-4-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The loop on entry of ata_host_start() may not initialize host->ops to a
non NULL value. The test on the host_stop field of host->ops must then
be preceded by a check that host->ops is not NULL.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20210816014456.2191776-3-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Prepare for removal of the request pointer by using scsi_cmd_to_rq()
instead. This patch does not change any functionality.
Link: https://lore.kernel.org/r/20210809230355.8186-8-bvanassche@acm.org
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
taregeted for v5.15:
- Add DT bindings to the expansion bus and PATA libata driver.
- Add a new expansion bus driver.
- Rewrite the watchdog driver to use the watchdog core and
spawn from the timer (clocksource) driver.
- Refactor the PATA/libata driver to probe from the device
tree and use the expansion bus driver to manipulate chip
select timings directly.
-----BEGIN PGP SIGNATURE-----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=v2E7
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=2bLl
-----END PGP SIGNATURE-----
Merge tag 'ixp4xx-drivers-arm-soc-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/drivers
IXP4xx driver updates for modernizing the IXP4xx platforms,
taregeted for v5.15:
- Add DT bindings to the expansion bus and PATA libata driver.
- Add a new expansion bus driver.
- Rewrite the watchdog driver to use the watchdog core and
spawn from the timer (clocksource) driver.
- Refactor the PATA/libata driver to probe from the device
tree and use the expansion bus driver to manipulate chip
select timings directly.
* tag 'ixp4xx-drivers-arm-soc-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
pata: ixp4xx: Rewrite to use device tree
pata: ixp4xx: Add DT bindings
pata: ixp4xx: Refer to cmd and ctl rather than csN
pata: ixp4xx: Use IS_ENABLED() to determine endianness
pata: ixp4xx: Use local dev variable
watchdog: ixp4xx: Rewrite driver to use core
bus: ixp4xx: Add a driver for IXP4xx expansion bus
bus: ixp4xx: Add DT bindings for the IXP4xx expansion bus
Link: https://lore.kernel.org/r/CACRpkdZaCosXsgp02nuUbd_nEvdxm5-z0+d0oSA97UTWQ0RQQg@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This rewrites the IXP4xx CF (IDE) libata driver to use the
device tree exclusively to look up its resources:
- Probe exclusively from the device tree and look up all
resources from there.
- Allocate a local state container with devres and pass
this around in .private_data.
- Initialize with struct ata_port_info.
- Use the .set_piomode() callback instead of the much
wider .set_mode(), we only support PIO after all.
- Bump driver version number from 0.2 to 1.0 to reflect this
wider change.
- Get a handle on the expansion bus syscon regmap to alter
the timings on the chip select.
- Put in the more elaborate timing adjustment code for PIO0
to PIO4 in 8 and 16bit mode from the downstream OpenWrt
patch.
The board file initialization path and platform data include
is dropped because the board files will be deleted at the same
time as this patch is merged.
The platform data file is not deleted right now so as not to
conflict with the removal of board files.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The two "cs0" and "cs1" are "chip selects" but on some
platforms such as GW2358 they are actually both in CS3
making this terminology very confusing. Call the
addresses "cmd" and "ctl" after function instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
